include/configs/aev.h - 3rdparty/u-boot - Gitiles Standalone

 /*
  * (C) Copyright 2003-2006
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * (C) Copyright 2004-2005
  * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_MPC5xxx		1	/* This is an MPC5xxx CPU */
 #define CONFIG_MPC5200		1	/* (more precisely an MPC5200 CPU) */
 #define CONFIG_TQM5200		1	/* ... on TQM5200 module */
 #undef CONFIG_TQM5200_REV100		/*  define for revision 100 modules */
 #define CONFIG_STK52XX		1	/* ... on a STK52XX base board */
 #define CONFIG_STK52XX_REV100	1	/*  define for revision 100 baseboards */
 #define CONFIG_AEVFIFO		1
 #define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */

 #define CONFIG_HIGH_BATS	1	/* High BATs supported */

 #define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH  */
 #define BOOTFLAG_WARM		0x02	/* Software reboot	     */

 /*
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
 #define CONFIG_BAUDRATE		115200	/* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }

 /*
  * PCI Mapping:
  * 0x40000000 - 0x4fffffff - PCI Memory
  * 0x50000000 - 0x50ffffff - PCI IO Space
  */
 #ifdef CONFIG_AEVFIFO
 #define CONFIG_PCI		1
 #define CONFIG_PCI_PNP		1
 /* #define CONFIG_PCI_SCAN_SHOW	1 */
 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE		1

 #define CONFIG_PCI_MEM_BUS	0x40000000
 #define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
 #define CONFIG_PCI_MEM_SIZE	0x10000000

 #define CONFIG_PCI_IO_BUS	0x50000000
 #define CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
 #define CONFIG_PCI_IO_SIZE	0x01000000

 #define CONFIG_NET_MULTI	1
 #define CONFIG_EEPRO100		1
 #define CONFIG_SYS_RX_ETH_BUFFER	8  /* use 8 rx buffer on eepro100  */
 #define CONFIG_NS8382X		1
 #endif	/* CONFIG_AEVFIFO */

 /* Partitions */
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
 #define CONFIG_ISO_PARTITION

 /* POST support */
 #define CONFIG_POST		(CONFIG_SYS_POST_MEMORY   | \
 				 CONFIG_SYS_POST_CPU	   | \
 				 CONFIG_SYS_POST_I2C)

 #ifdef CONFIG_POST
 /* preserve space for the post_word at end of on-chip SRAM */
 #define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
 #endif


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ECHO
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SNTP

 #ifdef CONFIG_POST
 #define CONFIG_CMD_DIAG
 #endif


 #define	CONFIG_TIMESTAMP		/* display image timestamps */

 #if (TEXT_BASE == 0xFC000000)		/* Boot low */
 #   define CONFIG_SYS_LOWBOOT		1
 #endif

 /*
  * Autobooting
  */
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */

 #define CONFIG_PREBOOT	"echo;" \
 	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"

 #undef	CONFIG_BOOTARGS

 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"rootpath=/opt/eldk/ppc_6xx\0"					\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath} "			\
 		"console=ttyS0,${baudrate}\0"				\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"flash_self=run ramargs addip;"					\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"flash_nfs=run nfsargs addip;"					\
 		"bootm ${kernel_addr}\0"				\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"bootfile=/tftpboot/tqm5200/uImage\0"				\
 	"load=tftp 200000 ${u-boot}\0"					\
 	"u-boot=/tftpboot/tqm5200/u-boot.bin\0"				\
 	"update=protect off FC000000 FC05FFFF;"				\
 		"erase FC000000 FC05FFFF;"				\
 		"cp.b 200000 FC000000 ${filesize};"			\
 		"protect on FC000000 FC05FFFF\0"			\
 	""

 #define CONFIG_BOOTCOMMAND	"run net_nfs"

 /*
  * IPB Bus clocking configuration.
  */
 #define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */

 #if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
 /*
  * PCI Bus clocking configuration
  *
  * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
  * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
  * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
  */
 #define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2	/* define for 66MHz speed */
 #endif

 /*
  * I2C configuration
  */
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support */
 #ifdef CONFIG_TQM5200_REV100
 #define CONFIG_SYS_I2C_MODULE		1	/* Select I2C module #1 for rev. 100 board */
 #else
 #define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #2 for all other revs */
 #endif

 /*
  * I2C clock frequency
  *
  * Please notice, that the resulting clock frequency could differ from the
  * configured value. This is because the I2C clock is derived from system
  * clock over a frequency divider with only a few divider values. U-boot
  * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
  * approximation allways lies below the configured value, never above.
  */
 #define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
 #define CONFIG_SYS_I2C_SLAVE		0x7F

 /*
  * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
  * also). For other EEPROMs configuration should be verified. On Mini-FAP the
  * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
  * same configuration could be used.
  */
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5	/* =32 Bytes per write */
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20

 /*
  * Flash configuration
  */
 #define CONFIG_SYS_FLASH_BASE		TEXT_BASE /* 0xFC000000 */

 /* use CFI flash driver if no module variant is spezified */
 #define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
 #define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_BOOTCS_START }
 #define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_FLASH_SIZE		0x04000000 /* 64 MByte */
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* max num of sects on one chip */
 #undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE	/* not supported yet for AMD */

 #if !defined(CONFIG_SYS_LOWBOOT)
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000)
 #else	/* CONFIG_SYS_LOWBOOT */
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00060000)
 #endif	/* CONFIG_SYS_LOWBOOT */
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks
 					   (= chip selects) */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)	*/
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/


 /*
  * Environment settings
  */
 #define CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_SIZE		0x10000
 #define CONFIG_ENV_SECT_SIZE	0x20000
 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 #define	CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

 /*
  * Memory map
  */
 #define CONFIG_SYS_MBAR		0xF0000000
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_DEFAULT_MBAR	0x80000000

 /* Use ON-Chip SRAM until RAM will be available */
 #define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
 #ifdef CONFIG_POST
 /* preserve space for the post_word at end of on-chip SRAM */
 #define CONFIG_SYS_INIT_RAM_END	MPC5XXX_SRAM_POST_SIZE
 #else
 #define CONFIG_SYS_INIT_RAM_END	MPC5XXX_SRAM_SIZE
 #endif


 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT		1
 #endif

 #define CONFIG_SYS_MONITOR_LEN		(384 << 10)	/* Reserve 384 kB for Monitor	*/
 #define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

 /*
  * Ethernet configuration
  */
 #define CONFIG_MPC5xxx_FEC	1
 /*
  * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
  */
 /* #define CONFIG_FEC_10MBIT 1 */
 #define CONFIG_PHY_ADDR		0x00

 /*
  * GPIO configuration
  *
  * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
  *	Bit 0 (mask: 0x80000000): 1
  * use ALT CAN position: Bits 2-3 (mask: 0x30000000):
  *	00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
  *	01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
  *	      Use for REV200 STK52XX boards. Do not use with REV100 modules
  *	      (because, there I2C1 is used as I2C bus)
  * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
  * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030)
  *	000 -> All PSC2 pins are GIOPs
  *	001 -> CAN1/2 on PSC2 pins
  *	       Use for REV100 STK52xx boards
  * use PSC6:
  *   on STK52xx:
  *	use as UART. Pins PSC6_0 to PSC6_3 are used.
  *	Bits 9:11 (mask: 0x00700000):
  *	   101 -> PSC6 : Extended POST test is not available
  *   on MINI-FAP and TQM5200_IB:
  *	use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000):
  *	   000 -> PSC6 could not be used as UART, CODEC or IrDA
  *   GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
  *   tests.
  */
 #define CONFIG_SYS_GPS_PORT_CONFIG	0x81500014

 /*
  * RTC configuration
  */
 #define CONFIG_RTC_MPC5200	1	/* use internal MPC5200 RTC */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
 #define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt   */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

 /* Enable an alternate, more extensive memory test */
 #define CONFIG_SYS_ALT_MEMTEST

 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/

 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */

 #define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks */

 #define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
 #if defined(CONFIG_CMD_KGDB)
 #  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif

 /*
  * Enable loopw command.
  */
 #define CONFIG_LOOPW

 /*
  * Various low-level settings
  */
 #if defined(CONFIG_MPC5200)
 #define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL		HID0_ICE
 #else
 #define CONFIG_SYS_HID0_INIT		0
 #define CONFIG_SYS_HID0_FINAL		0
 #endif

 #define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
 #ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
 #define CONFIG_SYS_BOOTCS_CFG		0x0008DF30 /* for pci_clk  = 66 MHz */
 #else
 #define CONFIG_SYS_BOOTCS_CFG		0x0004DF30 /* for pci_clk = 33 MHz */
 #endif
 #define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE

 #define CONFIG_LAST_STAGE_INIT

 /*
  * SRAM - Do not map below 2 GB in address space, because this area is used
  * for SDRAM autosizing.
  */
 #define CONFIG_SYS_CS2_START		0xE5000000
 #define CONFIG_SYS_CS2_SIZE		0x80000		/* 512 kByte */
 #define CONFIG_SYS_CS2_CFG		0x0004D930

 /*
  * Grafic controller - Do not map below 2 GB in address space, because this
  * area is used for SDRAM autosizing.
  */
 #define SM501_FB_BASE           0xE0000000
 #define CONFIG_SYS_CS1_START           (SM501_FB_BASE)
 #define CONFIG_SYS_CS1_SIZE            0x4000000       /* 64 MByte */
 #define CONFIG_SYS_CS1_CFG             0x8F48FF70
 #define SM501_MMIO_BASE         CONFIG_SYS_CS1_START + 0x03E00000

 #define CONFIG_SYS_CS_BURST            0x00000000
 #define CONFIG_SYS_CS_DEADCYCLE        0x33333311      /* 1 dead cycle for flash and SM501 */

 #define CONFIG_SYS_RESET_ADDRESS	0xff000000

 #endif /* __CONFIG_H */
	/*
	* (C) Copyright 2003-2006
	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	*
	* (C) Copyright 2004-2005
	* Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
	#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
	#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
	#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */
	#define CONFIG_STK52XX 1 /* ... on a STK52XX base board */
	#define CONFIG_STK52XX_REV100 1 /* define for revision 100 baseboards */
	#define CONFIG_AEVFIFO 1
	#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */

	#define CONFIG_HIGH_BATS 1 /* High BATs supported */

	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	/*
	* Serial console configuration
	*/
	#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
	#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }

	/*
	* PCI Mapping:
	* 0x40000000 - 0x4fffffff - PCI Memory
	* 0x50000000 - 0x50ffffff - PCI IO Space
	*/
	#ifdef CONFIG_AEVFIFO
	#define CONFIG_PCI 1
	#define CONFIG_PCI_PNP 1
	/* #define CONFIG_PCI_SCAN_SHOW 1 */
	#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1

	#define CONFIG_PCI_MEM_BUS 0x40000000
	#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
	#define CONFIG_PCI_MEM_SIZE 0x10000000

	#define CONFIG_PCI_IO_BUS 0x50000000
	#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
	#define CONFIG_PCI_IO_SIZE 0x01000000

	#define CONFIG_NET_MULTI 1
	#define CONFIG_EEPRO100 1
	#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
	#define CONFIG_NS8382X 1
	#endif /* CONFIG_AEVFIFO */

	/* Partitions */
	#define CONFIG_MAC_PARTITION
	#define CONFIG_DOS_PARTITION
	#define CONFIG_ISO_PARTITION

	/* POST support */
	#define CONFIG_POST (CONFIG_SYS_POST_MEMORY \| \
	CONFIG_SYS_POST_CPU \| \
	CONFIG_SYS_POST_I2C)

	#ifdef CONFIG_POST
	/* preserve space for the post_word at end of on-chip SRAM */
	#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
	#endif


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_ASKENV
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_ECHO
	#define CONFIG_CMD_EEPROM
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_NFS
	#define CONFIG_CMD_PCI
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_REGINFO
	#define CONFIG_CMD_SNTP

	#ifdef CONFIG_POST
	#define CONFIG_CMD_DIAG
	#endif


	#define CONFIG_TIMESTAMP /* display image timestamps */

	#if (TEXT_BASE == 0xFC000000) /* Boot low */
	# define CONFIG_SYS_LOWBOOT 1
	#endif

	/*
	* Autobooting
	*/
	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */

	#define CONFIG_PREBOOT "echo;" \
	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
	"echo"

	#undef CONFIG_BOOTARGS

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"rootpath=/opt/eldk/ppc_6xx\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath} " \
	"console=ttyS0,${baudrate}\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"flash_self=run ramargs addip;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"flash_nfs=run nfsargs addip;" \
	"bootm ${kernel_addr}\0" \
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
	"bootfile=/tftpboot/tqm5200/uImage\0" \
	"load=tftp 200000 ${u-boot}\0" \
	"u-boot=/tftpboot/tqm5200/u-boot.bin\0" \
	"update=protect off FC000000 FC05FFFF;" \
	"erase FC000000 FC05FFFF;" \
	"cp.b 200000 FC000000 ${filesize};" \
	"protect on FC000000 FC05FFFF\0" \
	""

	#define CONFIG_BOOTCOMMAND "run net_nfs"

	/*
	* IPB Bus clocking configuration.
	*/
	#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */

	#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
	/*
	* PCI Bus clocking configuration
	*
	* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
	* CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
	* of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
	*/
	#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
	#endif

	/*
	* I2C configuration
	*/
	#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
	#ifdef CONFIG_TQM5200_REV100
	#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */
	#else
	#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */
	#endif

	/*
	* I2C clock frequency
	*
	* Please notice, that the resulting clock frequency could differ from the
	* configured value. This is because the I2C clock is derived from system
	* clock over a frequency divider with only a few divider values. U-boot
	* calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
	* approximation allways lies below the configured value, never above.
	*/
	#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
	#define CONFIG_SYS_I2C_SLAVE 0x7F

	/*
	* EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
	* also). For other EEPROMs configuration should be verified. On Mini-FAP the
	* EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
	* same configuration could be used.
	*/
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20

	/*
	* Flash configuration
	*/
	#define CONFIG_SYS_FLASH_BASE TEXT_BASE /* 0xFC000000 */

	/* use CFI flash driver if no module variant is spezified */
	#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
	#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
	#define CONFIG_SYS_FLASH_EMPTY_INFO
	#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
	#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */

	#if !defined(CONFIG_SYS_LOWBOOT)
	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000)
	#else /* CONFIG_SYS_LOWBOOT */
	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000)
	#endif /* CONFIG_SYS_LOWBOOT */
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
	(= chip selects) */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */


	/*
	* Environment settings
	*/
	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_SIZE 0x10000
	#define CONFIG_ENV_SECT_SIZE 0x20000
	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)

	/*
	* Memory map
	*/
	#define CONFIG_SYS_MBAR 0xF0000000
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_DEFAULT_MBAR 0x80000000

	/* Use ON-Chip SRAM until RAM will be available */
	#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
	#ifdef CONFIG_POST
	/* preserve space for the post_word at end of on-chip SRAM */
	#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
	#else
	#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE
	#endif


	#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	# define CONFIG_SYS_RAMBOOT 1
	#endif

	#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*
	* Ethernet configuration
	*/
	#define CONFIG_MPC5xxx_FEC 1
	/*
	* Define CONFIG_FEC_10MBIT to force FEC at 10Mb
	*/
	/* #define CONFIG_FEC_10MBIT 1 */
	#define CONFIG_PHY_ADDR 0x00

	/*
	* GPIO configuration
	*
	* use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
	* Bit 0 (mask: 0x80000000): 1
	* use ALT CAN position: Bits 2-3 (mask: 0x30000000):
	* 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
	* 01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
	* Use for REV200 STK52XX boards. Do not use with REV100 modules
	* (because, there I2C1 is used as I2C bus)
	* use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
	* use PSC2 as CAN: Bits 25:27 (mask: 0x00000030)
	* 000 -> All PSC2 pins are GIOPs
	* 001 -> CAN1/2 on PSC2 pins
	* Use for REV100 STK52xx boards
	* use PSC6:
	* on STK52xx:
	* use as UART. Pins PSC6_0 to PSC6_3 are used.
	* Bits 9:11 (mask: 0x00700000):
	* 101 -> PSC6 : Extended POST test is not available
	* on MINI-FAP and TQM5200_IB:
	* use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000):
	* 000 -> PSC6 could not be used as UART, CODEC or IrDA
	* GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
	* tests.
	*/
	#define CONFIG_SYS_GPS_PORT_CONFIG 0x81500014

	/*
	* RTC configuration
	*/
	#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	/* Enable an alternate, more extensive memory test */
	#define CONFIG_SYS_ALT_MEMTEST

	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */

	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */

	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
	#if defined(CONFIG_CMD_KGDB)
	# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif

	/*
	* Enable loopw command.
	*/
	#define CONFIG_LOOPW

	/*
	* Various low-level settings
	*/
	#if defined(CONFIG_MPC5200)
	#define CONFIG_SYS_HID0_INIT HID0_ICE \| HID0_ICFI
	#define CONFIG_SYS_HID0_FINAL HID0_ICE
	#else
	#define CONFIG_SYS_HID0_INIT 0
	#define CONFIG_SYS_HID0_FINAL 0
	#endif

	#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
	#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
	#define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
	#else
	#define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
	#endif
	#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE

	#define CONFIG_LAST_STAGE_INIT

	/*
	* SRAM - Do not map below 2 GB in address space, because this area is used
	* for SDRAM autosizing.
	*/
	#define CONFIG_SYS_CS2_START 0xE5000000
	#define CONFIG_SYS_CS2_SIZE 0x80000 /* 512 kByte */
	#define CONFIG_SYS_CS2_CFG 0x0004D930

	/*
	* Grafic controller - Do not map below 2 GB in address space, because this
	* area is used for SDRAM autosizing.
	*/
	#define SM501_FB_BASE 0xE0000000
	#define CONFIG_SYS_CS1_START (SM501_FB_BASE)
	#define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */
	#define CONFIG_SYS_CS1_CFG 0x8F48FF70
	#define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000

	#define CONFIG_SYS_CS_BURST 0x00000000
	#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */

	#define CONFIG_SYS_RESET_ADDRESS 0xff000000

	#endif /* __CONFIG_H */