blob: e7caefa0b9c2687475e1458098c3ebb6dbbf66bf [file] [log] [blame]
MediaTek XS-PHY binding
The XS-PHY controller supports physical layer functionality for USB3.1
GEN2 controller on MediaTek SoCs.
Required properties (controller (parent) node):
- compatible : should be "mediatek,<soc-model>-xsphy", "mediatek,xsphy",
soc-model is the name of SoC, such as mt3611 etc;
when using "mediatek,xsphy" compatible string, you need SoC specific
ones in addition, one of:
- "mediatek,mt3611-xsphy"
- #address-cells, #size-cells : should use the same values as the root node
- ranges: must be present
Optional properties (controller (parent) node):
- reg : offset and length of register shared by multiple U3 ports,
exclude port's private register, if only U2 ports provided,
shouldn't use the property.
- mediatek,src-ref-clk-mhz : u32, frequency of reference clock for slew rate
- mediatek,src-coef : u32, coefficient for slew rate calibrate, depends on
SoC process
Required nodes : a sub-node is required for each port the controller
provides. Address range information including the usual
'reg' property is used inside these nodes to describe
the controller's topology.
Required properties (port (child) node):
- reg : address and length of the register set for the port.
- clocks : a list of phandle + clock-specifier pairs, one for each
entry in clock-names
- clock-names : must contain
"ref": 48M reference clock for HighSpeed analog phy; and 26M
reference clock for SuperSpeedPlus analog phy, sometimes is
24M, 25M or 27M, depended on platform.
- #phy-cells : should be 1
cell after port phandle is phy type from:
The following optional properties are only for debug or HQA test
Optional properties (PHY_TYPE_USB2 port (child) node):
- mediatek,eye-src : u32, the value of slew rate calibrate
- mediatek,eye-vrt : u32, the selection of VRT reference voltage
- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage
- mediatek,efuse-intr : u32, the selection of Internal Resistor
Optional properties (PHY_TYPE_USB3 port (child) node):
- mediatek,efuse-intr : u32, the selection of Internal Resistor
- mediatek,efuse-tx-imp : u32, the selection of TX Impedance
- mediatek,efuse-rx-imp : u32, the selection of RX Impedance
Banks layout of xsphy
port offset bank
u2 port0 0x0000 MISC
0x0100 FMREG
0x0300 U2PHY_COM
u2 port1 0x1000 MISC
0x1100 FMREG
0x1300 U2PHY_COM
u2 port2 0x2000 MISC
u31 common 0x3000 DIG_GLB
0x3100 PHYA_GLB
u31 port0 0x3400 DIG_LN_TOP
0x3500 DIG_LN_TX0
0x3600 DIG_LN_RX0
0x3700 DIG_LN_DAIF
0x3800 PHYA_LN
u31 port1 0x3a00 DIG_LN_TOP
0x3b00 DIG_LN_TX0
0x3c00 DIG_LN_RX0
0x3d00 DIG_LN_DAIF
0x3e00 PHYA_LN
DIG_GLB & PHYA_GLB are shared by U31 ports.
u3phy: usb-phy@11c40000 {
compatible = "mediatek,mt3611-xsphy", "mediatek,xsphy";
reg = <0 0x11c43000 0 0x0200>;
mediatek,src-ref-clk-mhz = <26>;
mediatek,src-coef = <17>;
#address-cells = <2>;
#size-cells = <2>;
u2port0: usb-phy@11c40000 {
reg = <0 0x11c40000 0 0x0400>;
clocks = <&clk48m>;
clock-names = "ref";
mediatek,eye-src = <4>;
#phy-cells = <1>;
u3port0: usb-phy@11c43000 {
reg = <0 0x11c43400 0 0x0500>;
clocks = <&clk26m>;
clock-names = "ref";
mediatek,efuse-intr = <28>;
#phy-cells = <1>;