iio: ad_sigma_delta: Properly handle SPI bus locking vs CS assertion
For devices from the SigmaDelta family we need to keep CS low when doing a
conversion, since the device will use the MISO line as a interrupt to
indicate that the conversion is complete.
This is why the driver locks the SPI bus and when the SPI bus is locked
keeps as long as a conversion is going on. The current implementation gets
one small detail wrong though. CS is only de-asserted after the SPI bus is
unlocked. This means it is possible for a different SPI device on the same
bus to send a message which would be wrongfully be addressed to the
SigmaDelta device as well. Make sure that the last SPI transfer that is
done while holding the SPI bus lock de-asserts the CS signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <Alexandru.Ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
diff --git a/drivers/iio/adc/ad_sigma_delta.c b/drivers/iio/adc/ad_sigma_delta.c
index ff5f2da..af6cbc6 100644
--- a/drivers/iio/adc/ad_sigma_delta.c
+++ b/drivers/iio/adc/ad_sigma_delta.c
@@ -62,7 +62,7 @@
struct spi_transfer t = {
.tx_buf = data,
.len = size + 1,
- .cs_change = sigma_delta->bus_locked,
+ .cs_change = sigma_delta->keep_cs_asserted,
};
struct spi_message m;
int ret;
@@ -217,6 +217,7 @@
spi_bus_lock(sigma_delta->spi->master);
sigma_delta->bus_locked = true;
+ sigma_delta->keep_cs_asserted = true;
reinit_completion(&sigma_delta->completion);
ret = ad_sigma_delta_set_mode(sigma_delta, mode);
@@ -234,9 +235,10 @@
ret = 0;
}
out:
+ sigma_delta->keep_cs_asserted = false;
+ ad_sigma_delta_set_mode(sigma_delta, AD_SD_MODE_IDLE);
sigma_delta->bus_locked = false;
spi_bus_unlock(sigma_delta->spi->master);
- ad_sigma_delta_set_mode(sigma_delta, AD_SD_MODE_IDLE);
return ret;
}
@@ -289,6 +291,7 @@
spi_bus_lock(sigma_delta->spi->master);
sigma_delta->bus_locked = true;
+ sigma_delta->keep_cs_asserted = true;
reinit_completion(&sigma_delta->completion);
ad_sigma_delta_set_mode(sigma_delta, AD_SD_MODE_SINGLE);
@@ -298,9 +301,6 @@
ret = wait_for_completion_interruptible_timeout(
&sigma_delta->completion, HZ);
- sigma_delta->bus_locked = false;
- spi_bus_unlock(sigma_delta->spi->master);
-
if (ret == 0)
ret = -EIO;
if (ret < 0)
@@ -321,7 +321,10 @@
sigma_delta->irq_dis = true;
}
+ sigma_delta->keep_cs_asserted = false;
ad_sigma_delta_set_mode(sigma_delta, AD_SD_MODE_IDLE);
+ sigma_delta->bus_locked = false;
+ spi_bus_unlock(sigma_delta->spi->master);
mutex_unlock(&indio_dev->mlock);
if (ret)
@@ -358,6 +361,8 @@
spi_bus_lock(sigma_delta->spi->master);
sigma_delta->bus_locked = true;
+ sigma_delta->keep_cs_asserted = true;
+
ret = ad_sigma_delta_set_mode(sigma_delta, AD_SD_MODE_CONTINUOUS);
if (ret)
goto err_unlock;
@@ -386,6 +391,7 @@
sigma_delta->irq_dis = true;
}
+ sigma_delta->keep_cs_asserted = false;
ad_sigma_delta_set_mode(sigma_delta, AD_SD_MODE_IDLE);
sigma_delta->bus_locked = false;