ARM: dts: Move move WiFi bindings to logicpd-torpedo-37xx-devkit
The newly added OMAP35xx Torpedo does not have a WiFi option, so
this patch moves the WL1283 binding and pin muxing to the
logicpd-torpedo-37xx-devkit since it's only applicable on that SOM
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
index b5404f0..234afd6 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
+++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
@@ -14,4 +14,64 @@
/ {
model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit";
compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3";
+
+ wl12xx_vmmc: wl12xx_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1271";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio5 29 0>; /* gpio157 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ vin-supply = <&vmmc2>;
+ };
+};
+
+/*
+ * Only found on the wireless SOM. For the SOM without wireless, the pins for
+ * MMC3 can be routed with jumpers to the second MMC slot on the devkit and
+ * gpio157 is not connected. So this should be OK to keep common for now,
+ * probably device tree overlays is the way to go with the various SOM and
+ * jumpering combinations for the long run.
+ */
+&mmc3 {
+ interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
+ pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
+ pinctrl-names = "default";
+ vmmc-supply = <&wl12xx_vmmc>;
+ non-removable;
+ bus-width = <4>;
+ cap-power-off-card;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1283";
+ reg = <2>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
+ ref-clock-frequency = <26000000>;
+ tcxo-clock-frequency = <26000000>;
+ };
+};
+
+&omap3_pmx_core {
+ mmc3_pins: pinmux_mm3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
+ OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
+ OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
+ OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
+ OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
+ OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */
+ >;
+ };
+};
+
+&omap3_pmx_core2 {
+ mmc3_core2_pins: pinmux_mmc3_core2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */
+ OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */
+ >;
+ };
};