powerpc/eeh: Remove eeh_handle_event()
The function eeh_handle_event(pe) does nothing other than switching
between calling eeh_handle_normal_event(pe) and
eeh_handle_special_event(). However it is only called in two places,
one where pe can't be NULL and the other where it must be NULL (see
eeh_event_handler()) so it does nothing but obscure the flow of
control.
So, remove it.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
diff --git a/arch/powerpc/kernel/eeh_driver.c b/arch/powerpc/kernel/eeh_driver.c
index 0c0b66f..51b21c9 100644
--- a/arch/powerpc/kernel/eeh_driver.c
+++ b/arch/powerpc/kernel/eeh_driver.c
@@ -738,9 +738,22 @@
* Attempts to recover the given PE. If recovery fails or the PE has failed
* too many times, remove the PE.
*
+ * While PHB detects address or data parity errors on particular PCI
+ * slot, the associated PE will be frozen. Besides, DMA's occurring
+ * to wild addresses (which usually happen due to bugs in device
+ * drivers or in PCI adapter firmware) can cause EEH error. #SERR,
+ * #PERR or other misc PCI-related errors also can trigger EEH errors.
+ *
+ * Recovery process consists of unplugging the device driver (which
+ * generated hotplug events to userspace), then issuing a PCI #RST to
+ * the device, then reconfiguring the PCI config space for all bridges
+ * & devices under this slot, and then finally restarting the device
+ * drivers (which cause a second set of hotplug events to go out to
+ * userspace).
+ *
* Returns true if @pe should no longer be used, else false.
*/
-static bool eeh_handle_normal_event(struct eeh_pe *pe)
+bool eeh_handle_normal_event(struct eeh_pe *pe)
{
struct pci_bus *frozen_bus;
struct eeh_dev *edev, *tmp;
@@ -942,7 +955,7 @@
* specific PE. Iterates through possible failures and handles them as
* necessary.
*/
-static void eeh_handle_special_event(void)
+void eeh_handle_special_event(void)
{
struct eeh_pe *pe, *phb_pe;
struct pci_bus *bus;
@@ -1049,28 +1062,3 @@
break;
} while (rc != EEH_NEXT_ERR_NONE);
}
-
-/**
- * eeh_handle_event - Reset a PCI device after hard lockup.
- * @pe: EEH PE
- *
- * While PHB detects address or data parity errors on particular PCI
- * slot, the associated PE will be frozen. Besides, DMA's occurring
- * to wild addresses (which usually happen due to bugs in device
- * drivers or in PCI adapter firmware) can cause EEH error. #SERR,
- * #PERR or other misc PCI-related errors also can trigger EEH errors.
- *
- * Recovery process consists of unplugging the device driver (which
- * generated hotplug events to userspace), then issuing a PCI #RST to
- * the device, then reconfiguring the PCI config space for all bridges
- * & devices under this slot, and then finally restarting the device
- * drivers (which cause a second set of hotplug events to go out to
- * userspace).
- */
-void eeh_handle_event(struct eeh_pe *pe)
-{
- if (pe)
- eeh_handle_normal_event(pe);
- else
- eeh_handle_special_event();
-}