Revert "net: ethernet: bcmgenet: use phydev from struct net_device"
This reverts commit 62469c76007e ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a6a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c76007e we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c76007e, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index 6d6f83b..55cbe2e 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -453,25 +453,29 @@
static int bcmgenet_get_settings(struct net_device *dev,
struct ethtool_cmd *cmd)
{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+
if (!netif_running(dev))
return -EINVAL;
- if (!dev->phydev)
+ if (!priv->phydev)
return -ENODEV;
- return phy_ethtool_gset(dev->phydev, cmd);
+ return phy_ethtool_gset(priv->phydev, cmd);
}
static int bcmgenet_set_settings(struct net_device *dev,
struct ethtool_cmd *cmd)
{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+
if (!netif_running(dev))
return -EINVAL;
- if (!dev->phydev)
+ if (!priv->phydev)
return -ENODEV;
- return phy_ethtool_sset(dev->phydev, cmd);
+ return phy_ethtool_sset(priv->phydev, cmd);
}
static int bcmgenet_set_rx_csum(struct net_device *dev,
@@ -937,7 +941,7 @@
e->eee_active = p->eee_active;
e->tx_lpi_timer = bcmgenet_umac_readl(priv, UMAC_EEE_LPI_TIMER);
- return phy_ethtool_get_eee(dev->phydev, e);
+ return phy_ethtool_get_eee(priv->phydev, e);
}
static int bcmgenet_set_eee(struct net_device *dev, struct ethtool_eee *e)
@@ -954,7 +958,7 @@
if (!p->eee_enabled) {
bcmgenet_eee_enable_set(dev, false);
} else {
- ret = phy_init_eee(dev->phydev, 0);
+ ret = phy_init_eee(priv->phydev, 0);
if (ret) {
netif_err(priv, hw, dev, "EEE initialization failed\n");
return ret;
@@ -964,12 +968,14 @@
bcmgenet_eee_enable_set(dev, true);
}
- return phy_ethtool_set_eee(dev->phydev, e);
+ return phy_ethtool_set_eee(priv->phydev, e);
}
static int bcmgenet_nway_reset(struct net_device *dev)
{
- return genphy_restart_aneg(dev->phydev);
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+
+ return genphy_restart_aneg(priv->phydev);
}
/* standard ethtool support functions. */
@@ -996,13 +1002,12 @@
static int bcmgenet_power_down(struct bcmgenet_priv *priv,
enum bcmgenet_power_mode mode)
{
- struct net_device *ndev = priv->dev;
int ret = 0;
u32 reg;
switch (mode) {
case GENET_POWER_CABLE_SENSE:
- phy_detach(ndev->phydev);
+ phy_detach(priv->phydev);
break;
case GENET_POWER_WOL_MAGIC:
@@ -1063,6 +1068,7 @@
/* ioctl handle special commands that are not present in ethtool. */
static int bcmgenet_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
int val = 0;
if (!netif_running(dev))
@@ -1072,10 +1078,10 @@
case SIOCGMIIPHY:
case SIOCGMIIREG:
case SIOCSMIIREG:
- if (!dev->phydev)
+ if (!priv->phydev)
val = -ENODEV;
else
- val = phy_mii_ioctl(dev->phydev, rq, cmd);
+ val = phy_mii_ioctl(priv->phydev, rq, cmd);
break;
default:
@@ -2458,7 +2464,6 @@
{
struct bcmgenet_priv *priv = container_of(
work, struct bcmgenet_priv, bcmgenet_irq_work);
- struct net_device *ndev = priv->dev;
netif_dbg(priv, intr, priv->dev, "%s\n", __func__);
@@ -2471,7 +2476,7 @@
/* Link UP/DOWN event */
if (priv->irq0_stat & UMAC_IRQ_LINK_EVENT) {
- phy_mac_interrupt(ndev->phydev,
+ phy_mac_interrupt(priv->phydev,
!!(priv->irq0_stat & UMAC_IRQ_LINK_UP));
priv->irq0_stat &= ~UMAC_IRQ_LINK_EVENT;
}
@@ -2711,7 +2716,7 @@
/* Monitor link interrupts now */
bcmgenet_link_intr_enable(priv);
- phy_start(dev->phydev);
+ phy_start(priv->phydev);
}
static int bcmgenet_open(struct net_device *dev)
@@ -2810,7 +2815,7 @@
struct bcmgenet_priv *priv = netdev_priv(dev);
netif_tx_stop_all_queues(dev);
- phy_stop(dev->phydev);
+ phy_stop(priv->phydev);
bcmgenet_intr_disable(priv);
bcmgenet_disable_rx_napi(priv);
bcmgenet_disable_tx_napi(priv);
@@ -2836,7 +2841,7 @@
bcmgenet_netif_stop(dev);
/* Really kill the PHY state machine and disconnect from it */
- phy_disconnect(dev->phydev);
+ phy_disconnect(priv->phydev);
/* Disable MAC receive */
umac_enable_set(priv, CMD_RX_EN, false);
@@ -3395,7 +3400,7 @@
bcmgenet_netif_stop(dev);
- phy_suspend(dev->phydev);
+ phy_suspend(priv->phydev);
netif_device_detach(dev);
@@ -3459,7 +3464,7 @@
if (priv->wolopts)
clk_disable_unprepare(priv->clk_wol);
- phy_init_hw(dev->phydev);
+ phy_init_hw(priv->phydev);
/* Speed settings must be restored */
bcmgenet_mii_config(priv->dev);
@@ -3492,7 +3497,7 @@
netif_device_attach(dev);
- phy_resume(dev->phydev);
+ phy_resume(priv->phydev);
if (priv->eee.eee_enabled)
bcmgenet_eee_enable_set(dev, true);
diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.h b/drivers/net/ethernet/broadcom/genet/bcmgenet.h
index 0f0868c..1e2dc34 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.h
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.h
@@ -597,6 +597,7 @@
/* MDIO bus variables */
wait_queue_head_t wq;
+ struct phy_device *phydev;
bool internal_phy;
struct device_node *phy_dn;
struct device_node *mdio_dn;
diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
index e907acd..457c3bc 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -86,7 +86,7 @@
void bcmgenet_mii_setup(struct net_device *dev)
{
struct bcmgenet_priv *priv = netdev_priv(dev);
- struct phy_device *phydev = dev->phydev;
+ struct phy_device *phydev = priv->phydev;
u32 reg, cmd_bits = 0;
bool status_changed = false;
@@ -183,9 +183,9 @@
if (GENET_IS_V4(priv))
return;
- if (dev->phydev) {
- phy_init_hw(dev->phydev);
- phy_start_aneg(dev->phydev);
+ if (priv->phydev) {
+ phy_init_hw(priv->phydev);
+ phy_start_aneg(priv->phydev);
}
}
@@ -236,7 +236,6 @@
static void bcmgenet_moca_phy_setup(struct bcmgenet_priv *priv)
{
- struct net_device *ndev = priv->dev;
u32 reg;
/* Speed settings are set in bcmgenet_mii_setup() */
@@ -245,14 +244,14 @@
bcmgenet_sys_writel(priv, reg, SYS_PORT_CTRL);
if (priv->hw_params->flags & GENET_HAS_MOCA_LINK_DET)
- fixed_phy_set_link_update(ndev->phydev,
+ fixed_phy_set_link_update(priv->phydev,
bcmgenet_fixed_phy_link_update);
}
int bcmgenet_mii_config(struct net_device *dev)
{
struct bcmgenet_priv *priv = netdev_priv(dev);
- struct phy_device *phydev = dev->phydev;
+ struct phy_device *phydev = priv->phydev;
struct device *kdev = &priv->pdev->dev;
const char *phy_name = NULL;
u32 id_mode_dis = 0;
@@ -303,7 +302,7 @@
* capabilities, use that knowledge to also configure the
* Reverse MII interface correctly.
*/
- if ((phydev->supported & PHY_BASIC_FEATURES) ==
+ if ((priv->phydev->supported & PHY_BASIC_FEATURES) ==
PHY_BASIC_FEATURES)
port_ctrl = PORT_MODE_EXT_RVMII_25;
else
@@ -372,7 +371,7 @@
return -ENODEV;
}
} else {
- phydev = dev->phydev;
+ phydev = priv->phydev;
phydev->dev_flags = phy_flags;
ret = phy_connect_direct(dev, phydev, bcmgenet_mii_setup,
@@ -383,6 +382,8 @@
}
}
+ priv->phydev = phydev;
+
/* Configure port multiplexer based on what the probed PHY device since
* reading the 'max-speed' property determines the maximum supported
* PHY speed which is needed for bcmgenet_mii_config() to configure
@@ -390,7 +391,7 @@
*/
ret = bcmgenet_mii_config(dev);
if (ret) {
- phy_disconnect(phydev);
+ phy_disconnect(priv->phydev);
return ret;
}
@@ -400,7 +401,7 @@
* Ethernet MAC ISRs
*/
if (priv->internal_phy)
- phydev->irq = PHY_IGNORE_INTERRUPT;
+ priv->phydev->irq = PHY_IGNORE_INTERRUPT;
return 0;
}
@@ -605,6 +606,7 @@
}
+ priv->phydev = phydev;
priv->phy_interface = pd->phy_interface;
return 0;