bnx2x: GPIO accessories
A GPIO is used with the 8726 PHY. Adding the GPIO related functions in this
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c
index 9c40b02..95f8e58 100644
--- a/drivers/net/bnx2x_main.c
+++ b/drivers/net/bnx2x_main.c
@@ -626,8 +626,8 @@
if (IS_E1HMF(bp)) {
val = (0xee0f | (1 << (BP_E1HVN(bp) + 4)));
if (bp->port.pmf)
- /* enable nig attention */
- val |= 0x0100;
+ /* enable nig and gpio3 attention */
+ val |= 0x1100;
} else
val = 0xffff;
@@ -1836,6 +1836,36 @@
mutex_unlock(&bp->port.phy_mutex);
}
+int bnx2x_get_gpio(struct bnx2x *bp, int gpio_num, u8 port)
+{
+ /* The GPIO should be swapped if swap register is set and active */
+ int gpio_port = (REG_RD(bp, NIG_REG_PORT_SWAP) &&
+ REG_RD(bp, NIG_REG_STRAP_OVERRIDE)) ^ port;
+ int gpio_shift = gpio_num +
+ (gpio_port ? MISC_REGISTERS_GPIO_PORT_SHIFT : 0);
+ u32 gpio_mask = (1 << gpio_shift);
+ u32 gpio_reg;
+ int value;
+
+ if (gpio_num > MISC_REGISTERS_GPIO_3) {
+ BNX2X_ERR("Invalid GPIO %d\n", gpio_num);
+ return -EINVAL;
+ }
+
+ /* read GPIO value */
+ gpio_reg = REG_RD(bp, MISC_REG_GPIO);
+
+ /* get the requested pin value */
+ if ((gpio_reg & gpio_mask) == gpio_mask)
+ value = 1;
+ else
+ value = 0;
+
+ DP(NETIF_MSG_LINK, "pin %d value 0x%x\n", gpio_num, value);
+
+ return value;
+}
+
int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode, u8 port)
{
/* The GPIO should be swapped if swap register is set and active */
@@ -1889,6 +1919,52 @@
return 0;
}
+int bnx2x_set_gpio_int(struct bnx2x *bp, int gpio_num, u32 mode, u8 port)
+{
+ /* The GPIO should be swapped if swap register is set and active */
+ int gpio_port = (REG_RD(bp, NIG_REG_PORT_SWAP) &&
+ REG_RD(bp, NIG_REG_STRAP_OVERRIDE)) ^ port;
+ int gpio_shift = gpio_num +
+ (gpio_port ? MISC_REGISTERS_GPIO_PORT_SHIFT : 0);
+ u32 gpio_mask = (1 << gpio_shift);
+ u32 gpio_reg;
+
+ if (gpio_num > MISC_REGISTERS_GPIO_3) {
+ BNX2X_ERR("Invalid GPIO %d\n", gpio_num);
+ return -EINVAL;
+ }
+
+ bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_GPIO);
+ /* read GPIO int */
+ gpio_reg = REG_RD(bp, MISC_REG_GPIO_INT);
+
+ switch (mode) {
+ case MISC_REGISTERS_GPIO_INT_OUTPUT_CLR:
+ DP(NETIF_MSG_LINK, "Clear GPIO INT %d (shift %d) -> "
+ "output low\n", gpio_num, gpio_shift);
+ /* clear SET and set CLR */
+ gpio_reg &= ~(gpio_mask << MISC_REGISTERS_GPIO_INT_SET_POS);
+ gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_INT_CLR_POS);
+ break;
+
+ case MISC_REGISTERS_GPIO_INT_OUTPUT_SET:
+ DP(NETIF_MSG_LINK, "Set GPIO INT %d (shift %d) -> "
+ "output high\n", gpio_num, gpio_shift);
+ /* clear CLR and set SET */
+ gpio_reg &= ~(gpio_mask << MISC_REGISTERS_GPIO_INT_CLR_POS);
+ gpio_reg |= (gpio_mask << MISC_REGISTERS_GPIO_INT_SET_POS);
+ break;
+
+ default:
+ break;
+ }
+
+ REG_WR(bp, MISC_REG_GPIO_INT, gpio_reg);
+ bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_GPIO);
+
+ return 0;
+}
+
static int bnx2x_set_spio(struct bnx2x *bp, int spio_num, u32 mode)
{
u32 spio_mask = (1 << spio_num);