[SPARC]: Add sun4m LED driver.

[linux-3.10.git] / arch / sparc / Kconfig

diff --git a/arch/sparc/Kconfig b/arch/sparc/Kconfig
index aba05394d30a05603685e2bcc62cc9c2b85b4d3b..3cfb8be3ff6d0f9fe5be0c600a9f035787f767d4 100644 (file)
--- a/arch/sparc/Kconfig
+++ b/arch/sparc/Kconfig
@@ -25,62 +25,6 @@ source "init/Kconfig"
 
 menu "General machine setup"
 
-config VT
-       bool
-       select INPUT
-       default y
-       ---help---
-         If you say Y here, you will get support for terminal devices with
-         display and keyboard devices. These are called "virtual" because you
-         can run several virtual terminals (also called virtual consoles) on
-         one physical terminal. This is rather useful, for example one
-         virtual terminal can collect system messages and warnings, another
-         one can be used for a text-mode user session, and a third could run
-         an X session, all in parallel. Switching between virtual terminals
-         is done with certain key combinations, usually Alt-<function key>.
-
-         The setterm command ("man setterm") can be used to change the
-         properties (such as colors or beeping) of a virtual terminal. The
-         man page console_codes(4) ("man console_codes") contains the special
-         character sequences that can be used to change those properties
-         directly. The fonts used on virtual terminals can be changed with
-         the setfont ("man setfont") command and the key bindings are defined
-         with the loadkeys ("man loadkeys") command.
-
-         You need at least one virtual terminal device in order to make use
-         of your keyboard and monitor. Therefore, only people configuring an
-         embedded system would want to say N here in order to save some
-         memory; the only way to log into such a system is then via a serial
-         or network connection.
-
-         If unsure, say Y, or else you won't be able to do much with your new
-         shiny Linux system :-)
-
-config VT_CONSOLE
-       bool
-       default y
-       ---help---
-         The system console is the device which receives all kernel messages
-         and warnings and which allows logins in single user mode. If you
-         answer Y here, a virtual terminal (the device used to interact with
-         a physical terminal) can be used as system console. This is the most
-         common mode of operations, so you should say Y here unless you want
-         the kernel messages be output only to a serial port (in which case
-         you should say Y to "Console on serial port", below).
-
-         If you do say Y here, by default the currently visible virtual
-         terminal (/dev/tty0) will be used as system console. You can change
-         that with a kernel command line option such as "console=tty3" which
-         would use the third virtual terminal as system console. (Try "man
-         bootparam" or see the documentation of your boot loader (lilo or
-         loadlin) about how to pass options to the kernel at boot time.)
-
-         If unsure, say Y.
-
-config HW_CONSOLE
-       bool
-       default y
-
 config SMP
        bool "Symmetric multi-processing support (does not work on sun4/sun4c)"
        depends on BROKEN
@@ -257,6 +201,14 @@ config SUN_OPENPROMFS
          Only choose N if you know in advance that you will not need to modify
          OpenPROM settings on the running system.
 
+config SPARC_LED
+       tristate "Sun4m LED driver"
+       help
+         This driver toggles the front-panel LED on sun4m systems
+         in a user-specifyable manner.  It's state can be probed
+         by reading /proc/led and it's blinking mode can be changed
+         via writes to /proc/led
+
 source "fs/Kconfig.binfmt"
 
 config SUNOS_EMUL