]> nv-tegra.nvidia Code Review - linux-2.6.git/log
13 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
Linus Torvalds [Fri, 5 Feb 2010 19:11:34 +0000 (11:11 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ASoC: pandora: Add APLL supply to fix audio output
  ALSA: ice1724 - aureon - fix wm8770 volume offset
  ALSA: cosmetic: make hda intel interrupt name consistent with others
  ALSA: hda - Delay switching to polling mode if an interrupt was missing
  ALSA: ctxfi - fix PTP address initialization

13 years agoMerge remote branch 'alsa/fixes' into for-linus
Takashi Iwai [Fri, 5 Feb 2010 18:57:23 +0000 (19:57 +0100)]
Merge remote branch 'alsa/fixes' into for-linus

13 years agoMerge branch 'fix/asoc' into for-linus
Takashi Iwai [Fri, 5 Feb 2010 18:57:16 +0000 (19:57 +0100)]
Merge branch 'fix/asoc' into for-linus

13 years agoMerge branch 'fix/hda' into for-linus
Takashi Iwai [Fri, 5 Feb 2010 18:56:55 +0000 (19:56 +0100)]
Merge branch 'fix/hda' into for-linus

13 years agoMerge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzi...
Linus Torvalds [Fri, 5 Feb 2010 15:58:21 +0000 (07:58 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] Call flush_dcache_page after PIO data transfers in libata-sff.c
  ahci: add Acer G725 to broken suspend list
  libata: fix ata_id_logical_per_physical_sectors
  libata-scsi passthru: fix bug which truncated LBA48 return values

13 years agoCS5536: apply pci quirk for BIOS SMBUS bug
Andres Salomon [Fri, 5 Feb 2010 06:42:43 +0000 (01:42 -0500)]
CS5536: apply pci quirk for BIOS SMBUS bug

The new cs5535-* drivers use PCI header config info rather than MSRs to
determine the memory region to use for things like GPIOs and MFGPTs.  As
anticipated, we've run into a buggy BIOS:

[    0.081818] pci 0000:00:14.0: reg 10: [io  0x6000-0x7fff]
[    0.081906] pci 0000:00:14.0: reg 14: [io  0x6100-0x61ff]
[    0.082015] pci 0000:00:14.0: reg 18: [io  0x6200-0x63ff]
[    0.082917] pci 0000:00:14.2: reg 20: [io  0xe000-0xe00f]
[    0.083551] pci 0000:00:15.0: reg 10: [mem 0xa0010000-0xa0010fff]
[    0.084436] pci 0000:00:15.1: reg 10: [mem 0xa0011000-0xa0011fff]
[    0.088816] PCI: pci_cache_line_size set to 32 bytes
[    0.088938] pci 0000:00:14.0: address space collision: [io 0x6100-0x61ff] already in use
[    0.089052] pci 0000:00:14.0: can't reserve [io  0x6100-0x61ff]

This is a Soekris board, and its BIOS sets the size of the PCI ISA bridge
device's BAR0 to 8k.  In reality, it should be 8 bytes (BAR0 is used for
SMBus stuff).  This quirk checks for an incorrect size, and resets it

Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Tested-by: Leigh Porter <leigh@leighporter.org>
Tested-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agopercpu: add __percpu for sparse
Stephen Rothwell [Fri, 5 Feb 2010 05:09:11 +0000 (16:09 +1100)]
percpu: add __percpu for sparse

This is to make the annotation of percpu variables during the next merge
window less painfull.

Extracted from a patch by Rusty Russell.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoMerge branch 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied...
Linus Torvalds [Fri, 5 Feb 2010 15:24:01 +0000 (07:24 -0800)]
Merge branch 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: fix r300 vram width calculations
  drm/radeon/kms: rs400/480 MC setup is different than r300.
  drm/radeon/kms: make initial state of load detect property correct.
  drm/radeon/kms: disable HDMI audio for now on rv710/rv730
  drm/radeon/kms: don't call suspend path before cleaning up GPU
  drivers/gpu/drm/radeon/radeon_combios.c: fix warning
  ati_pcigart: fix printk format warning
  drm/r100/kms: Emit cache flush to the end of command buffer. (v2)
  drm/radeon/kms: fix regression rendering issue on R6XX/R7XX
  drm/radeon/kms: move blit initialization after we disabled VGA

13 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable
Linus Torvalds [Fri, 5 Feb 2010 15:23:03 +0000 (07:23 -0800)]
Merge git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: apply updated fallocate i_size fix
  Btrfs: do not try and lookup the file extent when finishing ordered io
  Btrfs: Fix oopsen when dropping empty tree.
  Btrfs: remove BUG_ON() due to mounting bad filesystem
  Btrfs: make error return negative in btrfs_sync_file()
  Btrfs: fix race between allocate and release extent buffer.

13 years agoASoC: pandora: Add APLL supply to fix audio output
Grazvydas Ignotas [Thu, 4 Feb 2010 22:55:33 +0000 (00:55 +0200)]
ASoC: pandora: Add APLL supply to fix audio output

Pandora's external DAC is using 256*Fs output from the TWL4030
codec, and TWL4030 needs to have APLL enabled for it's 256*Fs
output to function.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
13 years agoALSA: ice1724 - aureon - fix wm8770 volume offset
Jaroslav Kysela [Fri, 5 Feb 2010 09:19:41 +0000 (10:19 +0100)]
ALSA: ice1724 - aureon - fix wm8770 volume offset

The volume register is from 0..0x7f and 0..0x1a range is mute.
Also, fix mute combining in wm_vol_put(). The wrong behaviour was
noticed by Peter Christensen.

Signed-off-by: Jaroslav Kysela <perex@perex.cz>
13 years agoALSA: cosmetic: make hda intel interrupt name consistent with others
Maxim Levitsky [Thu, 4 Feb 2010 20:26:37 +0000 (22:26 +0200)]
ALSA: cosmetic: make hda intel interrupt name consistent with others

This renames the interrupt name in /proc/interrupt.
HDA Intel -> hda_intel

This also eliminates space from the name, probably helping some
Don't think anybody depends on this name in userspace

Signed-off-by: Takashi Iwai <tiwai@suse.de>
13 years agoALSA: hda - Delay switching to polling mode if an interrupt was missing
Maxim Levitsky [Thu, 4 Feb 2010 20:21:47 +0000 (22:21 +0200)]
ALSA: hda - Delay switching to polling mode if an interrupt was missing

My sound codec seems sometimes (very rarely) to omit interrupts (ALC268)
However, interrupt mode still works.
Thus if we get timeout, poll the codec once.

If we get 3 such polls in a row, then switch to polling mode.

This patch is maybe an bandaid, but this might be a workaround for hardware bug.

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
13 years agodrm/radeon/kms: fix r300 vram width calculations
Dave Airlie [Fri, 5 Feb 2010 03:57:03 +0000 (13:57 +1000)]
drm/radeon/kms: fix r300 vram width calculations

This was incorrect according to the docs and the UMS driver does
it like this.

Signed-off-by: Dave Airlie <airlied@redhat.com>
13 years agodrm/radeon/kms: rs400/480 MC setup is different than r300.
Dave Airlie [Fri, 5 Feb 2010 03:41:54 +0000 (13:41 +1000)]
drm/radeon/kms: rs400/480 MC setup is different than r300.

Boot testing on my rs480 laptop found the MC idle never happened
on startup, a quick check with AMD found the idle bit is in a different
place on the rs4xx than r300.

Implement a new rs400 mc idle function to fix this.

Signed-off-by: Dave Airlie <airlied@redhat.com>
13 years agodrm/radeon/kms: make initial state of load detect property correct.
Dave Airlie [Wed, 27 Jan 2010 06:07:15 +0000 (16:07 +1000)]
drm/radeon/kms: make initial state of load detect property correct.

this was incorrect on my rs480.

Signed-off-by: Dave Airlie <airlied@redhat.com>
13 years agodrm/radeon/kms: disable HDMI audio for now on rv710/rv730
Dave Airlie [Fri, 5 Feb 2010 01:57:42 +0000 (11:57 +1000)]
drm/radeon/kms: disable HDMI audio for now on rv710/rv730

Support isn't correct yet and we are getting green tinges on the

Signed-off-by: Dave Airlie <airlied@redhat.com>
13 years agodrm/radeon/kms: don't call suspend path before cleaning up GPU
Jerome Glisse [Tue, 2 Feb 2010 10:51:45 +0000 (11:51 +0100)]
drm/radeon/kms: don't call suspend path before cleaning up GPU

In suspend path we unmap the GART table while in cleaning up
path we will unbind buffer and thus try to write to unmapped
GART leading to oops. In order to avoid this we don't call the
suspend path in cleanup path. Cleanup path is clever enough
to desactive GPU like the suspend path is doing, thus this was

Tested on: RV370, R420, RV515, RV570, RV610, RV770 (all PCIE)

Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
13 years agodrivers/gpu/drm/radeon/radeon_combios.c: fix warning
Andrew Morton [Tue, 2 Feb 2010 22:40:29 +0000 (14:40 -0800)]
drivers/gpu/drm/radeon/radeon_combios.c: fix warning

drivers/gpu/drm/radeon/radeon_combios.c: In function 'radeon_combios_get_lvds_info':
drivers/gpu/drm/radeon/radeon_combios.c:893: warning: comparison is always false due to limited range of data type

Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
13 years agoati_pcigart: fix printk format warning
Randy Dunlap [Tue, 2 Feb 2010 22:40:33 +0000 (14:40 -0800)]
ati_pcigart: fix printk format warning

Fix ati_pcigart printk format warning:

drivers/gpu/drm/ati_pcigart.c:115: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'dma_addr_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
13 years agodrm/r100/kms: Emit cache flush to the end of command buffer. (v2)
Pauli Nieminen [Thu, 4 Feb 2010 17:20:53 +0000 (19:20 +0200)]
drm/r100/kms: Emit cache flush to the end of command buffer. (v2)

Cache flush is required in case CPU is accessing rendered data.

This fixes glean/readPixSanity test case and random rendering
errors in sauerbraten and warzone2100.

v2 Fix comment ordering in r100_fence_ring_emit and remove extra
   defines added in first version.

Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
13 years agodrm/radeon/kms: fix regression rendering issue on R6XX/R7XX
Jerome Glisse [Thu, 4 Feb 2010 19:36:39 +0000 (20:36 +0100)]
drm/radeon/kms: fix regression rendering issue on R6XX/R7XX

It seems that some R6XX/R7XX silently ignore HDP flush when
programmed through ring, this patch addback an ioctl callback
to allow R6XX/R7XX hw to perform such flush through MMIO in
order to fix a regression. For more details see:


Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
13 years agodrm/radeon/kms: move blit initialization after we disabled VGA
Jerome Glisse [Thu, 4 Feb 2010 16:27:27 +0000 (17:27 +0100)]
drm/radeon/kms: move blit initialization after we disabled VGA

VGA might be overwritting VRAM and corrupt our blit shader leading
to corruption, it likely won't happen if you load fbcon right after
radeon. Thanks to Shawn Starr and Andre Maasikas for tracking down
this issue.

Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
13 years agoMerge master.kernel.org:/home/rmk/linux-2.6-arm
Linus Torvalds [Fri, 5 Feb 2010 00:09:01 +0000 (16:09 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: Fix wrong register in proc-arm6_7.S data abort handler
  ARM: 5909/1: ARM: Correct the FPSCR bits setting when raising exceptions
  ARM: 5904/1: ARM: Always generate the IT instruction when compiling for Thumb-2
  ARM: 5907/1: ARM: Fix the reset on the RealView PBX Development board
  mx35: add a missing comma in a pad definition
  mx25: make the FEC AHB clk secondary of the IPG
  mx25: fix time accounting
  mx25: properly initialize clocks
  mx25: remove unused mx25_clocks_init() argument
  i.MX25: implement secondary clocks for uarts and fec
  i.MX25: Allow secondary clocks in DEFINE_CLOCK
  ARM: MX3: Fixed typo in declared enum type name.
  MXC: Add AUDMUXv2 register decode to debugfs
  mx31ads: Provide an IRQ range to the WM835x on the 1133-EV1 module
  mx31ads: Provide a name for EXPIO interrupt chip
  mx31ads: Allow enable/disable of switchable supplies

13 years agoMerge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Fri, 5 Feb 2010 00:08:42 +0000 (16:08 -0800)]
Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  omap: Disable serial port autoidle by default
  omap: Fix access to already released memory in clk_debugfs_register_one()
  omap: Fix arch/arm/mach-omap2/mux.c: Off by one error
  omap: Fix 3630 mux errors
  OMAP2/3: GPMC: ensure valid clock pointer
  OMAP2/3: IRQ: ensure valid base address
  omap: Remove old unused defines for OMAP_32KSYNCT_BASE
  omap: define _toggle_gpio_edge_triggering only for OMAP1

13 years agoMerge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
Linus Torvalds [Fri, 5 Feb 2010 00:08:15 +0000 (16:08 -0800)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: Don't clobber the attribute type in nfs_update_inode()
  NFS: Fix a umount race
  NFS: Fix an Oops when truncating a file
  NFS: Ensure that we handle NFS4ERR_STALE_STATEID correctly
  NFSv4.1: Don't call nfs4_schedule_state_recovery() unnecessarily
  NFSv4: Don't allow posix locking against servers that don't support it
  NFSv4: Ensure that the NFSv4 locking can recover from stateid errors
  NFS: Avoid warnings when CONFIG_NFS_V4=n
  NFS: Make nfs_commitdata_release static
  NFS: Try to commit unstable writes in nfs_release_page()
  NFS: Fix a reference leak in nfs_wb_cancel_page()

13 years agoMerge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Fri, 5 Feb 2010 00:07:41 +0000 (16:07 -0800)]
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  futex: Handle futex value corruption gracefully
  futex: Handle user space corruption gracefully
  futex_lock_pi() key refcnt fix
  softlockup: Add sched_clock_tick() to avoid kernel warning on kgdb resume

13 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes
Linus Torvalds [Fri, 5 Feb 2010 00:06:48 +0000 (16:06 -0800)]
Merge git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
  GFS2: Extend umount wait coverage to full glock lifetime
  GFS2: Wait for unlock completion on umount

13 years agoidr: revert misallocation bug fix
Tejun Heo [Thu, 4 Feb 2010 08:57:37 +0000 (17:57 +0900)]
idr: revert misallocation bug fix

Commit 859ddf09743a8cc680af33f7259ccd0fd36bfe9d tried to fix
misallocation bug but broke full bit marking by not clearing
pa[idp->layers] and also is causing X failures due to lookup failure
in drm code.  The cause of the latter hasn't been found yet.  Revert
the fix for now.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoALSA: ctxfi - fix PTP address initialization
Jaroslav Kysela [Tue, 2 Feb 2010 18:58:25 +0000 (19:58 +0100)]
ALSA: ctxfi - fix PTP address initialization

After hours of debugging, I finally found the reason why some source
and runtime combination does not work. The PTP (page table pages)
address must be aligned. I am not sure how much, but alignment to
PAGE_SIZE is sufficient. Also, use ALSA's page allocation routines
to ensure proper virtual -> physical address translation.

Cc: <stable@kernel.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
13 years agoBtrfs: apply updated fallocate i_size fix
Aneesh Kumar K.V [Thu, 4 Feb 2010 16:33:03 +0000 (11:33 -0500)]
Btrfs: apply updated fallocate i_size fix

This version of the i_size fix for fallocate makes sure we only update
the i_size when the current fallocate is really operating outside of

Signed-off-by: Chris Mason <chris.mason@oracle.com>
13 years agoBtrfs: do not try and lookup the file extent when finishing ordered io
Josef Bacik [Tue, 2 Feb 2010 20:50:10 +0000 (20:50 +0000)]
Btrfs: do not try and lookup the file extent when finishing ordered io

When running the following fio job


you would see long stalls where no work was being done.  That is because we were
doing all this extra work to read in the file extent outside of the transaction,
however in the random io case this ends up hurting us because the file extents
are not there to begin with.  So axe this logic, since we end up reading in the
file extent when we go to update it anyway.  This took the fio job from 11 mb/s
with several ~10 second stalls to 24 mb/s to a couple of 1-2 second stalls.

Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
13 years agoBtrfs: Fix oopsen when dropping empty tree.
Yan, Zheng [Mon, 1 Feb 2010 02:41:17 +0000 (02:41 +0000)]
Btrfs: Fix oopsen when dropping empty tree.

When dropping a empty tree, walk_down_tree() skips checking
extent information for the tree root. This will triggers a
BUG_ON in walk_up_proc().

Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
13 years agoBtrfs: remove BUG_ON() due to mounting bad filesystem
Miao Xie [Tue, 2 Feb 2010 08:46:44 +0000 (08:46 +0000)]
Btrfs: remove BUG_ON() due to mounting bad filesystem

Mounting a bad filesystem caused a BUG_ON(). The following is steps to
reproduce it.
 # mkfs.btrfs /dev/sda2
 # mount /dev/sda2 /mnt
 # mkfs.btrfs /dev/sda1 /dev/sda2
 (the program says that /dev/sda2 was mounted, and then exits. )
 # umount /mnt
 # mount /dev/sda1 /mnt

At the third step, mkfs.btrfs exited in the way of make filesystem. So the
initialization of the filesystem didn't finish. So the filesystem was bad, and
it caused BUG_ON() when mounting it. But BUG_ON() should be called by the wrong
code, not user's operation, so I think it is a bug of btrfs.

This patch fixes it.

Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
13 years agoBtrfs: make error return negative in btrfs_sync_file()
Roel Kluin [Fri, 29 Jan 2010 10:42:11 +0000 (10:42 +0000)]
Btrfs: make error return negative in btrfs_sync_file()

It appears the error return should be negative

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
13 years agoBtrfs: fix race between allocate and release extent buffer.
Yan, Zheng [Thu, 4 Feb 2010 08:46:56 +0000 (08:46 +0000)]
Btrfs: fix race between allocate and release extent buffer.

Increase extent buffer's reference count while holding the lock.
Otherwise it can race with try_release_extent_buffer.

Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
13 years ago[libata] Call flush_dcache_page after PIO data transfers in libata-sff.c
Catalin Marinas [Thu, 4 Feb 2010 06:04:50 +0000 (01:04 -0500)]
[libata] Call flush_dcache_page after PIO data transfers in libata-sff.c

flush_dcache_page() must be called after (!ATA_TFLAG_WRITE) the
data copying to avoid D-cache aliasing with user space or I-D cache
coherency issues (when reading data from an ATA device using PIO,
the kernel dirties the D-cache but there is no flush_dcache_page()
required on Harvard architectures).

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
13 years agoahci: add Acer G725 to broken suspend list
Tejun Heo [Thu, 28 Jan 2010 07:04:15 +0000 (16:04 +0900)]
ahci: add Acer G725 to broken suspend list

Acer G725 shares the same suspend problem with the HP laptops which
lose ATA devices on resume.  New firmware which fixes the problem is
already available.  Add G725 with old firmwares to the broken suspend

This problem has been reported in bko#15104.


Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jani-Matti Hätinen <jani-matti.hatinen@iki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
13 years agolibata: fix ata_id_logical_per_physical_sectors
Christoph Hellwig [Thu, 28 Jan 2010 12:30:11 +0000 (13:30 +0100)]
libata: fix ata_id_logical_per_physical_sectors

The value we get from the low byte of the ATA_ID_SECTOR_SIZE word is not not
a plain multiple, but the log of it, so fix the helper to give the correct
answer.  Without this we'll get an incorrect minimal I/O size in the block
limits VPD page for 4k sector drives.

Also change the return value of ata_id_logical_per_physical_sectors to u16
for the unlikely case of very large logical sectors.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
13 years agolibata-scsi passthru: fix bug which truncated LBA48 return values
Douglas Gilbert [Mon, 1 Feb 2010 18:11:38 +0000 (13:11 -0500)]
libata-scsi passthru: fix bug which truncated LBA48 return values

Fix assignment which overwrote SAT ATA PASS-THROUGH command EXTEND
bit setting (ATA_TFLAG_LBA48)

Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
13 years agoMerge branch 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze
Linus Torvalds [Thu, 4 Feb 2010 00:08:50 +0000 (16:08 -0800)]
Merge branch 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze

* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: fix interrupt state restore
  microblaze: Defconfig update

13 years agoMerge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab...
Linus Torvalds [Thu, 4 Feb 2010 00:08:36 +0000 (16:08 -0800)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  saa7146: stop DMA before de-allocating DMA scatter/gather page buffers
  V4L/DVB: saa7134: remove stray unlock_kernel

13 years agoomap: Disable serial port autoidle by default
Tony Lindgren [Mon, 1 Feb 2010 20:34:31 +0000 (12:34 -0800)]
omap: Disable serial port autoidle by default

Currently the omap serial clocks are autoidled after 5 seconds.
However, this causes lost characters on the serial ports. As this
is considered non-standard behaviour for Linux, disable the timeout.

Note that this will also cause blocking of any deeper omap sleep

To enable the autoidling of the serial ports, do something like
this for each serial port:

# echo 5 > /sys/devices/platform/serial8250.0/sleep_timeout
# echo 5 > /sys/devices/platform/serial8250.1/sleep_timeout

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
13 years agoomap: Fix access to already released memory in clk_debugfs_register_one()
Marek Skuczynski [Sun, 31 Jan 2010 10:00:54 +0000 (10:00 +0000)]
omap: Fix access to already released memory in clk_debugfs_register_one()

I have found an access to already released memory in
clk_debugfs_register_one() function.

Signed-off-by: Marek Skuczynski <mareksk7@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
13 years agoomap: Fix arch/arm/mach-omap2/mux.c: Off by one error
Tony Lindgren [Mon, 1 Feb 2010 21:03:42 +0000 (13:03 -0800)]
omap: Fix arch/arm/mach-omap2/mux.c: Off by one error

David Binderman ran the sourceforge tool cppcheck over the source code of the
new Linux kernel 2.6.33-rc6:

[./arm/mach-omap2/mux.c:492]: (error) Buffer access out-of-bounds

13 characters + 1 digit + 1 zero byte is more than 14 characters.

Also add a comment on mode0 name length in case new omaps
start using longer names.

Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
13 years agoomap: Fix 3630 mux errors
Tony Lindgren [Mon, 1 Feb 2010 19:22:54 +0000 (11:22 -0800)]
omap: Fix 3630 mux errors

3630 has more mux signals than 34xx. The additional pins
exist in omap36xx_cbp_subset, but are not initialized
as the superset is missing these offsets. This causes
the following errors during the boot:

mux: Unknown entry offset 0x236
mux: Unknown entry offset 0x22e
mux: Unknown entry offset 0x1ec
mux: Unknown entry offset 0x1ee
mux: Unknown entry offset 0x1f4
mux: Unknown entry offset 0x1f6
mux: Unknown entry offset 0x1f8
mux: Unknown entry offset 0x1fa
mux: Unknown entry offset 0x1fc
mux: Unknown entry offset 0x22a
mux: Unknown entry offset 0x226
mux: Unknown entry offset 0x230
mux: Unknown entry offset 0x22c
mux: Unknown entry offset 0x228

Fix this by adding the missing offsets to omap3 superset.
Note that additionally the uninitialized pins need to be
skipped on 34xx.

Based on an earlier patch by Allen Pais <allen.pais@ti.com>.

Reported-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
13 years agoOMAP2/3: GPMC: ensure valid clock pointer
Kevin Hilman [Fri, 29 Jan 2010 22:20:06 +0000 (14:20 -0800)]
OMAP2/3: GPMC: ensure valid clock pointer

Ensure valid clock pointer during GPMC init.  Fixes compiler
warning about potential use of uninitialized variable.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
13 years agoOMAP2/3: IRQ: ensure valid base address
Kevin Hilman [Fri, 29 Jan 2010 22:20:06 +0000 (14:20 -0800)]
OMAP2/3: IRQ: ensure valid base address

Ensure valid base address during IRQ init.  Fixes compiler warning
about potential use of uninitialized variable.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sriram [Fri, 29 Jan 2010 22:20:05 +0000 (14:20 -0800)]

OMAP platforms(like OMAP3530) include DSP or other co-processors
for media acceleration. when carving out memory for the
accelerators we can end up creating a hole in the memory map
of sort:
<kernel memory><hole(memory for accelerator)><kernel memory>

To handle such a memory configuration ARCH_HAS_HOLES_MEMORYMODEL
has to be enabled. For further information refer discussion at:

Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
13 years agoomap: Remove old unused defines for OMAP_32KSYNCT_BASE
Tony Lindgren [Fri, 29 Jan 2010 22:20:05 +0000 (14:20 -0800)]
omap: Remove old unused defines for OMAP_32KSYNCT_BASE

Remove old unused defines for OMAP_32KSYNCT_BASE

Signed-off-by: Tony Lindgren <tony@atomide.com>
13 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke...
Linus Torvalds [Wed, 3 Feb 2010 16:47:15 +0000 (08:47 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix potential leak of dirty data on umount

13 years agoARM: Fix wrong register in proc-arm6_7.S data abort handler
Russell King [Wed, 3 Feb 2010 15:48:03 +0000 (15:48 +0000)]
ARM: Fix wrong register in proc-arm6_7.S data abort handler

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
13 years agofutex: Handle futex value corruption gracefully
Thomas Gleixner [Wed, 3 Feb 2010 08:33:05 +0000 (09:33 +0100)]
futex: Handle futex value corruption gracefully

The WARN_ON in lookup_pi_state which complains about a mismatch
between pi_state->owner->pid and the pid which we retrieved from the
user space futex is completely bogus.

The code just emits the warning and then continues despite the fact
that it detected an inconsistent state of the futex. A conveniant way
for user space to spam the syslog.

Replace the WARN_ON by a consistency check. If the values do not match
return -EINVAL and let user space deal with the mess it created.

This also fixes the missing task_pid_vnr() when we compare the
pi_state->owner pid with the futex value.

Reported-by: Jermome Marchand <jmarchan@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Darren Hart <dvhltc@us.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <stable@kernel.org>
13 years agofutex: Handle user space corruption gracefully
Thomas Gleixner [Tue, 2 Feb 2010 10:40:27 +0000 (11:40 +0100)]
futex: Handle user space corruption gracefully

If the owner of a PI futex dies we fix up the pi_state and set
pi_state->owner to NULL. When a malicious or just sloppy programmed
user space application sets the futex value to 0 e.g. by calling
pthread_mutex_init(), then the futex can be acquired again. A new
waiter manages to enqueue itself on the pi_state w/o damage, but on
unlock the kernel dereferences pi_state->owner and oopses.

Prevent this by checking pi_state->owner in the unlock path. If
pi_state->owner is not current we know that user space manipulated the
futex value. Ignore the mess and return -EINVAL.

This catches the above case and also the case where a task hijacks the
futex by setting the tid value and then tries to unlock it.

Reported-by: Jermome Marchand <jmarchan@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Darren Hart <dvhltc@us.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <stable@kernel.org>
13 years agofutex_lock_pi() key refcnt fix
Mikael Pettersson [Sat, 23 Jan 2010 21:36:29 +0000 (22:36 +0100)]
futex_lock_pi() key refcnt fix

This fixes a futex key reference count bug in futex_lock_pi(),
where a key's reference count is incremented twice but decremented
only once, causing the backing object to not be released.

If the futex is created in a temporary file in an ext3 file system,
this bug causes the file's inode to become an "undead" orphan,
which causes an oops from a BUG_ON() in ext3_put_super() when the
file system is unmounted. glibc's test suite is known to trigger this,
see <http://bugzilla.kernel.org/show_bug.cgi?id=14256>.

The bug is a regression from 2.6.28-git3, namely Peter Zijlstra's
38d47c1b7075bd7ec3881141bb3629da58f88dab "[PATCH] futex: rely on
get_user_pages() for shared futexes". That commit made get_futex_key()
also increment the reference count of the futex key, and updated its
callers to decrement the key's reference count before returning.
Unfortunately the normal exit path in futex_lock_pi() wasn't corrected:
the reference count is incremented by get_futex_key() and queue_lock(),
but the normal exit path only decrements once, via unqueue_me_pi().
The fix is to put_futex_key() after unqueue_me_pi(), since 2.6.31
this is easily done by 'goto out_put_key' rather than 'goto out'.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Darren Hart <dvhltc@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
13 years agoNFS: Don't clobber the attribute type in nfs_update_inode()
Trond Myklebust [Wed, 3 Feb 2010 13:27:35 +0000 (08:27 -0500)]
NFS: Don't clobber the attribute type in nfs_update_inode()

If the NFS_ATTR_FATTR_TYPE field isn't set in fattr->valid, then we should
not set the S_IFMT part of inode->i_mode.

Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
13 years agoNFS: Fix a umount race
Trond Myklebust [Wed, 3 Feb 2010 13:27:35 +0000 (08:27 -0500)]
NFS: Fix a umount race

Ensure that we unregister the bdi before kill_anon_super() calls
ida_remove() on our device name.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
13 years agoNFS: Fix an Oops when truncating a file
Trond Myklebust [Wed, 3 Feb 2010 13:27:22 +0000 (08:27 -0500)]
NFS: Fix an Oops when truncating a file

The VM/VFS does not allow mapping->a_ops->invalidatepage() to fail.
Unfortunately, nfs_wb_page_cancel() may fail if a fatal signal occurs.
Since the NFS code assumes that the page stays mapped for as long as the
writeback is active, we can end up Oopsing (among other things).

The only safe fix here is to convert nfs_wait_on_request(), so as to make
it uninterruptible (as is already the case with wait_on_page_writeback()).

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
13 years agomicroblaze: fix interrupt state restore
Steven J. Magnani [Mon, 1 Feb 2010 12:34:45 +0000 (06:34 -0600)]
microblaze: fix interrupt state restore

Interrupts must be disabled while an interrupt state restore
(prep for interrupt return) is in progress.
Code to do this was lost in the port to the mainline kernel.

Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
13 years agoGFS2: Extend umount wait coverage to full glock lifetime
Steven Whitehouse [Fri, 29 Jan 2010 15:21:27 +0000 (15:21 +0000)]
GFS2: Extend umount wait coverage to full glock lifetime

Although all glocks are, by the time of the umount glock wait,
scheduled for demotion, some of them haven't made it far
enough through the process for the original set of waiting
code to wait for them.

This extends the ref count to the whole glock lifetime in order
to ensure that the waiting does catch all glocks. It does make
it a bit more invasive, but it seems the only sensible solution
at the moment.

Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
13 years agoGFS2: Wait for unlock completion on umount
Steven Whitehouse [Mon, 25 Jan 2010 11:20:19 +0000 (11:20 +0000)]
GFS2: Wait for unlock completion on umount

This patch adds a wait on umount between the point at which we
dispose of all glocks and the point at which we unmount the
lock protocol. This ensures that we've received all the replies
to our unlock requests before we stop the locking.

Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Reported-by: Fabio M. Di Nitto <fdinitto@redhat.com>
13 years agomicroblaze: Defconfig update
Michal Simek [Wed, 3 Feb 2010 09:18:20 +0000 (10:18 +0100)]
microblaze: Defconfig update

There were several changes in Microblaze defconfig that's why
is good to update defconfigs.

Signed-off-by: Michal Simek <monstr@monstr.eu>
13 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris...
Linus Torvalds [Wed, 3 Feb 2010 02:12:22 +0000 (18:12 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  kernel/cred.c: use kmem_cache_free

13 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Wed, 3 Feb 2010 02:11:52 +0000 (18:11 -0800)]
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
  connector: Delete buggy notification code.
  be2net: use eq-id to calculate cev-isr reg offset
  Bluetooth: Use the control channel for raw HID reports
  Bluetooth: Add DFU driver for Atheros Bluetooth chipset AR3011
  Bluetooth: Redo checks in IRQ handler for shared IRQ support
  Bluetooth: Fix memory leak in L2CAP
  Bluetooth: Remove double free of SKB pointer in L2CAP
  cdc_ether: Partially revert "usbnet: Set link down initially ..."
  be2net: Fix memset() arg ordering.
  bonding: bond_open error return value
  ixgbe: if ixgbe_copy_dcb_cfg is going to fail learn about it early
  ixgbe: set the correct DCB bit for pg tx settings
  igbvf: fix issue w/ mapped_as_page being left set after unmap
  drivers/net: ks8851_mll ethernet network driver
  be2net: Bug fix to support newer generation of BE ASIC
  starfire: clean up properly if firmware loading fails
  mac80211: fix NULL pointer dereference when ftrace is enabled
  netfilter: ctnetlink: fix expectation mask dump
  ipv6: conntrack: Add member of user to nf_ct_frag6_queue structure
  ath9k: fix eeprom INI values override for 2GHz-only cards

13 years agopktcdvd: removing device does not remove its sysfs dir
Thadeu Lima de Souza Cascardo [Tue, 2 Feb 2010 21:44:17 +0000 (13:44 -0800)]
pktcdvd: removing device does not remove its sysfs dir

This is the counterpart to cba767175becadc5c4016cceb7bfdd2c7fe722f4
("pktcdvd: remove broken dev_t export of class devices").  Device is not
registered using dev_t, so it should not be destroyed using device_destroy
which looks up the device by dev_t.  This will fail and adding the device
again will fail with the "duplicate name" error.  This is fixed using
device_unregister instead of device_destroy.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomemory hotplug: fix a bug on /dev/mem for 64-bit kernels
Shaohui Zheng [Tue, 2 Feb 2010 21:44:16 +0000 (13:44 -0800)]
memory hotplug: fix a bug on /dev/mem for 64-bit kernels

Newly added memory can not be accessed via /dev/mem, because we do not
update the variables high_memory, max_pfn and max_low_pfn.

Add a function update_end_of_memory_vars() to update these variables for
64-bit kernels.

[akpm@linux-foundation.org: simplify comment]
Signed-off-by: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Li Haicheng <haicheng.li@intel.com>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agofault injection: correct function names in documentation
Anton Blanchard [Tue, 2 Feb 2010 21:44:15 +0000 (13:44 -0800)]
fault injection: correct function names in documentation

init_fault_attr_entries() should be init_fault_attr_dentries().

cleanup_fault_attr_entries() should be cleanup_fault_attr_dentries().

Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agohugetlb: fix section mismatches
Jeff Mahoney [Tue, 2 Feb 2010 21:44:14 +0000 (13:44 -0800)]
hugetlb: fix section mismatches

hugetlb_sysfs_add_hstate is called by hugetlb_register_node directly
during init and also indirectly via sysfs after init.

This patch removes the __init tag from hugetlb_sysfs_add_hstate.

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agouartlite: fix crash when using as console
Richard Röjfors [Tue, 2 Feb 2010 21:44:12 +0000 (13:44 -0800)]
uartlite: fix crash when using as console

Move the ulite_console_setup to the .devinit section since it might be
called on probe, which is in devinit.  Fixes the crash below where the
uartlite hw is probed after the .init section is freed from the kernel.

uartlite: ttyUL0 at MMIO 0xc8000100 (irq = 30) is a uartlite
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c176720e>] ulite_console_setup+0x6f/0xa8
*pdpt = 0000000036fb0001 *pde = 0000000000000000
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1f.1/host0/uevent
Modules linked in: puffin(+) serio_raw

Pid: 151, comm: modprobe Not tainted ( #1) POULSBO
EIP: 0060:[<c176720e>] EFLAGS: 00010246 CPU: 0
EIP is at ulite_console_setup+0x6f/0xa8
EAX: c16ec824 EBX: c16ec824 ECX: c176719f EDX: 00000000
ESI: 00000000 EDI: c17b42c4 EBP: f6fd1cf0 ESP: f6fd1cd8
 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process modprobe (pid: 151, ti=f6fd0000 task=f6fa1020 task.ti=f6fd0000)
 c1031f51 00000000 00000000 00000246 c182237c f7742000 f6fd1d5c c11fd316
<0> c16ec85c f77420d4 0000001e 00000000 00000000 c1633e78 4f494d4d 63783020
<0> 30303038 00303031 f6fd1d3c c10e0786 f6fd1d48 00000000 f6fd1d48 00000000
Call Trace:
 [<c1031f51>] ? register_console+0xf6/0x1fc
 [<c11fd316>] ? uart_add_one_port+0x237/0x2bb
 [<c10e0786>] ? sysfs_add_one+0x13/0xd3
 [<c10e142f>] ? sysfs_do_create_link+0xba/0xfc
 [<c146f200>] ? ulite_probe+0x198/0x1eb
 [<c12064ee>] ? platform_drv_probe+0xc/0xe
 [<c120597b>] ? driver_probe_device+0x79/0x105
 [<c1205a8e>] ? __device_attach+0x28/0x30
 [<c120511f>] ? bus_for_each_drv+0x3d/0x67
 [<c1205af9>] ? device_attach+0x44/0x58
 [<c1205a66>] ? __device_attach+0x0/0x30
 [<c1204fb8>] ? bus_probe_device+0x1f/0x34
 [<c1203e68>] ? device_add+0x385/0x4c0
 [<c148491f>] ? _write_unlock+0x8/0x1f
 [<c1206aac>] ? platform_device_add+0xd9/0x11c
 [<c120c685>] ? mfd_add_devices+0x165/0x1bc
 [<f831b378>] ? puffin_probe+0x2d0/0x390 [puffin]
 [<c11a08ef>] ? pci_match_device+0xa0/0xa7
 [<c11a07bc>] ? local_pci_probe+0xe/0x10
 [<c11a11db>] ? pci_device_probe+0x43/0x66
 [<c120597b>] ? driver_probe_device+0x79/0x105
 [<c1205a4a>] ? __driver_attach+0x43/0x5f
 [<c120535d>] ? bus_for_each_dev+0x3d/0x67
 [<c1205852>] ? driver_attach+0x14/0x16
 [<c1205a07>] ? __driver_attach+0x0/0x5f
 [<c1204dea>] ? bus_add_driver+0xf9/0x220
 [<c1205c8f>] ? driver_register+0x8b/0xeb
 [<c11a1518>] ? __pci_register_driver+0x43/0x9f
 [<c10477ef>] ? __blocking_notifier_call_chain+0x40/0x4c
 [<f831f000>] ? puffin_init+0x0/0x48 [puffin]
 [<f831f017>] ? puffin_init+0x17/0x48 [puffin]
 [<c1001139>] ? do_one_initcall+0x4c/0x131
 [<c105607b>] ? sys_init_module+0xa7/0x1b7
 [<c1002a61>] ? syscall_call+0x7/0xb
 Code: 6e 74 00 00 00 92 33 00 00 18 00 0e 01 73 79 6e 63 65 2d 72 65 67 69 73 74 72 79 0c 00 49 32
00 00 14 00 09 01 61 6c 73 61 2d 69 <6e> 66 6f 00 00 00 42 37 00 00 10 00 07 01 6b 69 6c 6c 61 6c 6c
EIP: [<c176720e>] ulite_console_setup+0x6f/0xa8 SS:ESP 0068:f6fd1cd8
CR2: 0000000000000000

Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoimxfb: correct location of callbacks in suspend and resume
Uwe Kleine-König [Tue, 2 Feb 2010 21:44:10 +0000 (13:44 -0800)]
imxfb: correct location of callbacks in suspend and resume

The probe function passes a pointer to a struct fb_info to
platform_set_drvdata(), so don't interpret the return value of
platform_get_drvdata() as a pointer to struct imxfb_info.

The original imxfb_info *fbi backlight_power was NULL but in imxfb_suspend
it was 4 resulting in an oops as imxfb_suspend calls
imxfb_disable_controller(fbi) which in turn has

if (fbi->backlight_power)

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agocgroups: fix to return errno in a failure path
Li Zefan [Tue, 2 Feb 2010 21:44:10 +0000 (13:44 -0800)]
cgroups: fix to return errno in a failure path

In cgroup_create(), if alloc_css_id() returns failure, the errno is not
propagated to userspace, so mkdir will fail silently.

To trigger this bug, we mount blkio (or memory subsystem), and create more
then 65534 cgroups.  (The number of cgroups is limited to 65535 if a
subsystem has use_id == 1)

 # mount -t cgroup -o blkio xxx /mnt
 # for ((i = 0; i < 65534; i++)); do mkdir /mnt/$i; done
 # mkdir /mnt/65534
 (should return ENOSPC)

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Paul Menage <menage@google.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomarkup_oops.pl: fix $func_offset error with x86_64
Hui Zhu [Tue, 2 Feb 2010 21:44:09 +0000 (13:44 -0800)]
markup_oops.pl: fix $func_offset error with x86_64

When I use markup_oops.pl parse a x8664 oops, I got:

objdump: --start-address: bad number: NaN
No matching code found
This is because:
main::(./m.pl:228): open(FILE, "objdump -dS --adjust-vma=$vmaoffset --start-address=$decodestart --stop-address=$decodestop $filename |") || die "Cannot start objdump";
  DB<3> p $decodestart

This NaN is from:
main::(./m.pl:176): my $decodestart = Math::BigInt->from_hex("0x$target") - Math::BigInt->from_hex("0x$func_offset");
  DB<2> p $func_offset

There is already a "0x" in $func_offset, another 0x makes it a NaN.

The $func_offset is from line:

if ($line =~ /RIP: 0010:\[\<[0-9a-f]+\>\]  \[\<[0-9a-f]+\>\] ([a-zA-Z0-9\_]+)\+(0x[0-9a-f]+)\/0x[a-f0-9]/) {
$function = $1;
$func_offset = $2;

I make a patch to change "(0x[0-9a-f]+)\/0x[a-f0-9]/)" to "0x([0-9a-f]+)\/0x[a-f0-9]/)".

Signed-off-by: Hui Zhu <teawater@gmail.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoget_maintainer.pl: teach git log to use --no-color
Richard Kennedy [Tue, 2 Feb 2010 21:44:07 +0000 (13:44 -0800)]
get_maintainer.pl: teach git log to use --no-color

When git has been set to always use color in .gitconfig then I get the
warning message

        Bad divisor in main::vcs_assign: 0

This is caused by vcs_file_signoffs not matching any commits due to the
pattern not understand the colour codes.  Fix this by telling git log to
never use colour.

Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Acked-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agodevmem: fix kmem write bug on memory holes
Wu Fengguang [Tue, 2 Feb 2010 21:44:06 +0000 (13:44 -0800)]
devmem: fix kmem write bug on memory holes

write_kmem() used to assume vwrite() always return the full buffer length.
However now vwrite() could return 0 to indicate memory hole.  This
creates a bug that "buf" is not advanced accordingly.

Fix it to simply ignore the return value, hence the memory hole.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <tj@kernel.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agodevmem: check vmalloc address on kmem read/write
KAMEZAWA Hiroyuki [Tue, 2 Feb 2010 21:44:05 +0000 (13:44 -0800)]
devmem: check vmalloc address on kmem read/write

Otherwise vmalloc_to_page() will BUG().

This also makes the kmem read/write implementation aligned with mem(4):
"References to nonexistent locations cause errors to be returned." Here we
return -ENXIO (inspired by Hugh) if no bytes have been transfered to/from
user space, otherwise return partial read/write results.

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomm: flush dcache before writing into page to avoid alias
anfei zhou [Tue, 2 Feb 2010 21:44:02 +0000 (13:44 -0800)]
mm: flush dcache before writing into page to avoid alias

The cache alias problem will happen if the changes of user shared mapping
is not flushed before copying, then user and kernel mapping may be mapped
into two different cache line, it is impossible to guarantee the coherence
after iov_iter_copy_from_user_atomic.  So the right steps should be:

write to page;

More precisely, we might create two new APIs flush_dcache_user_page and
flush_dcache_kern_page to replace the two flush_dcache_page accordingly.

Here is a snippet tested on omap2430 with VIPT cache, and I think it is
not ARM-specific:

int val = 0x11111111;
fd = open("abc", O_RDWR);
addr = mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_SHARED, fd, 0);
*(addr+0) = 0x44444444;
tmp = *(addr+0);
*(addr+1) = 0x77777777;
write(fd, &val, sizeof(int));

The results are not always 0x11111111 0x77777777 at the beginning as expected.  Sometimes we see 0x44444444 0x77777777.

Signed-off-by: Anfei <anfei.zhou@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: <linux-arch@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agokfifo: fix kernel-doc notation
Randy Dunlap [Tue, 2 Feb 2010 21:44:01 +0000 (13:44 -0800)]
kfifo: fix kernel-doc notation

Fix kfifo kernel-doc warnings:

Warning(kernel/kfifo.c:361): No description found for parameter 'total'
Warning(kernel/kfifo.c:402): bad line:  @ @lenout: pointer to output variable with copied data
Warning(kernel/kfifo.c:412): No description found for parameter 'lenout'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agortc-fm3130: add missing braces
Sergey Matyukevich [Tue, 2 Feb 2010 21:43:59 +0000 (13:43 -0800)]
rtc-fm3130: add missing braces

Add missing braces for multiline 'if' statements in fm3130_probe.

Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomx3fb: some debug and initialisation fixes
Alberto Panizzo [Tue, 2 Feb 2010 21:43:59 +0000 (13:43 -0800)]
mx3fb: some debug and initialisation fixes

Fix the kernel oops when dev_dbg is called with mx3_fbi->txd == NULL

Fix the late initialisation of mx3fb->backlight_level.  If not, in the
chain of function started by init_fb_chan(), in __blank() call
sdc_set_brightness(mx3fb, mx3fb->backlight_level) that will shut down the

Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski <at> gmx.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoidr: fix a critical misallocation bug
Tejun Heo [Tue, 2 Feb 2010 21:43:58 +0000 (13:43 -0800)]
idr: fix a critical misallocation bug

Eric Paris located a bug in idr.  With IDR_BITS of 6, it grows to three
layers when id 4096 is first allocated.  When that happens, idr wraps
incorrectly and searches the idr array ignoring the high bits.  The
following test code from Eric demonstrates the bug nicely.

#include <linux/idr.h>
#include <linux/kernel.h>
#include <linux/module.h>

static DEFINE_IDR(test_idr);

int init_module(void)
int ret, forty95, forty96;
void *addr;

/* add 2 entries both with 4095 as the start address */
if (!idr_pre_get(&test_idr, GFP_KERNEL))
return -ENOMEM;
ret = idr_get_new_above(&test_idr, (void *)4095, 4095, &forty95);
if (ret) {
if (ret == -EAGAIN)
goto again1;
return ret;
if (forty95 != 4095)
printk(KERN_ERR "hmmm, forty95=%d\n", forty95);

if (!idr_pre_get(&test_idr, GFP_KERNEL))
return -ENOMEM;
ret = idr_get_new_above(&test_idr, (void *)4096, 4095, &forty96);
if (ret) {
if (ret == -EAGAIN)
goto again2;
return ret;
if (forty96 != 4096)
printk(KERN_ERR "hmmm, forty96=%d\n", forty96);

/* try to find the 2 entries, noticing that 4096 broke */
addr = idr_find(&test_idr, forty95);
if ((int)addr != forty95)
printk(KERN_ERR "hmmm, after find forty95=%d addr=%d\n", forty95, (int)addr);
addr = idr_find(&test_idr, forty96);
if ((int)addr != forty96)
printk(KERN_ERR "hmmm, after find forty96=%d addr=%d\n", forty96, (int)addr);
/* really weird, the entry which should be at 4096 is actually at 0!! */
addr = idr_find(&test_idr, 0);
if ((int)addr)
printk(KERN_ERR "found an entry at id=0 for addr=%d\n", (int)addr);

idr_remove(&test_idr, forty95);
idr_remove(&test_idr, forty96);

return 0;

void cleanup_module(void)

MODULE_AUTHOR("Eric Paris <eparis@redhat.com>");
MODULE_DESCRIPTION("Simple idr test");

This happens because when sub_alloc() back tracks it doesn't always do it
step-by-step while the over-the-limit detection assumes step-by-step
backtracking.  The logic in sub_alloc() looks like the following.

    clear pa[top level + 1] for end cond detection
    l = top level
    while (true) {
search for empty slot at this level
if (not found) {
    push id to the next possible value
A:     if (pa[l] is clear)
        failed, return asking caller to grow the tree
    if (going up 1 level gives more slots to search)
        continue the while loop above with the incremented l
C:         goto restart
adjust id accordingly to the found slot
if (l == 0)
    return found id;
create lower level if not there yet
record pa[l] and l--

Test A is the fail exit condition but this assumes that failure is
propagated upwared one level at a time but the B optimization path breaks
the assumption and restarts the whole thing with a start value which is
above the possible limit with the current layers.  sub_alloc() assumes the
start id value is inside the limit when called and test A is the only exit
condition check, so it ends up searching for empty slot while ignoring
high set bit.

So, for 4095->4096 test, level0 search fails but pa[1] contains a valid
pointer.  However, going up 1 level wouldn't give any more empty slot so
it takes C and when the whole thing restarts nobody notices the high bit
set beyond the top level.

This patch fixes the bug by changing the fail exit condition check to full
id limit check.

Based-on-patch-from: Eric Paris <eparis@redhat.com>
Reported-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoconnector: Delete buggy notification code.
Evgeniy Polyakov [Tue, 2 Feb 2010 23:58:48 +0000 (15:58 -0800)]
connector: Delete buggy notification code.

On Tue, Feb 02, 2010 at 02:57:14PM -0800, Greg KH (gregkh@suse.de) wrote:
> > There are at least two ways to fix it: using a big cannon and a small
> > one. The former way is to disable notification registration, since it is
> > not used by anyone at all. Second way is to check whether calling
> > process is root and its destination group is -1 (kind of priveledged
> > one) before command is dispatched to workqueue.
> Well if no one is using it, removing it makes the most sense, right?
> No objection from me, care to make up a patch either way for this?

Getting it is not used, let's drop support for notifications about
(un)registered events from connector.
Another option was to check credentials on receiving, but we can always
restore it without bugs if needed, but genetlink has a wider code base
and none complained, that userspace can not get notification when some
other clients were (un)registered.

Kudos for Sebastian Krahmer <krahmer@suse.de>, who found a bug in the

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agokernel/cred.c: use kmem_cache_free
Julia Lawall [Tue, 2 Feb 2010 22:31:36 +0000 (09:31 +1100)]
kernel/cred.c: use kmem_cache_free

Free memory allocated using kmem_cache_zalloc using kmem_cache_free rather
than kfree.

The semantic patch that makes this change is as follows:

// <smpl>
expression x,E,c;

 x = \(kmem_cache_alloc\|kmem_cache_zalloc\|kmem_cache_alloc_node\)(c,...)
 ... when != x = E
     when != &x
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: Steve Dickson <steved@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
13 years agoMerge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
Linus Torvalds [Tue, 2 Feb 2010 20:54:37 +0000 (12:54 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  cfq-iosched: Do not idle on async queues
  blk-cgroup: Fix potential deadlock in blk-cgroup
  block: fix bugs in bio-integrity mempool usage
  block: fix bio_add_page for non trivial merge_bvec_fn case
  drbd: null dereference bug
  drbd: fix max_segment_size initialization

13 years agomm: purge fragmented percpu vmap blocks
Nick Piggin [Mon, 1 Feb 2010 11:25:57 +0000 (22:25 +1100)]
mm: purge fragmented percpu vmap blocks

Improve handling of fragmented per-CPU vmaps.  We previously don't free
up per-CPU maps until all its addresses have been used and freed.  So
fragmented blocks could fill up vmalloc space even if they actually had
no active vmap regions within them.

Add some logic to allow all CPUs to have these blocks purged in the case
of failure to allocate a new vm area, and also put some logic to trim
such blocks of a current CPU if we hit them in the allocation path (so
as to avoid a large build up of them).

Christoph reported some vmap allocation failures when using the per CPU
vmap APIs in XFS, which cannot be reproduced after this patch and the
previous bug fix.

Cc: linux-mm@kvack.org
Cc: stable@kernel.org
Tested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agomm: percpu-vmap fix RCU list walking
Nick Piggin [Mon, 1 Feb 2010 11:24:18 +0000 (22:24 +1100)]
mm: percpu-vmap fix RCU list walking

RCU list walking of the per-cpu vmap cache was broken.  It did not use
RCU primitives, and also the union of free_list and rcu_head is
obviously wrong (because free_list is indeed the list we are RCU

While we are there, remove a couple of unused fields from an earlier

These APIs aren't actually used anywhere, because of problems with the
XFS conversion.  Christoph has now verified that the problems are solved
with these patches.  Also it is an exported interface, so I think it
will be good to be merged now (and Christoph wants to get the XFS
changes into their local tree).

Cc: stable@kernel.org
Cc: linux-mm@kvack.org
Tested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Linus Torvalds [Tue, 2 Feb 2010 20:48:49 +0000 (12:48 -0800)]
Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  random: Remove unused inode variable
  crypto: padlock-sha - Add import/export support
  random: drop weird m_time/a_time manipulation

13 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes
Linus Torvalds [Tue, 2 Feb 2010 20:48:26 +0000 (12:48 -0800)]
Merge git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
  GFS2: Use GFP_NOFS for alloc structure
  GFS2: Fix previous patch
  GFS2: Don't withdraw on partial rindex entries
  GFS2: Fix refcnt leak on gfs2_follow_link() error path

13 years agoMerge branch 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal...
Linus Torvalds [Tue, 2 Feb 2010 20:47:51 +0000 (12:47 -0800)]
Merge branch 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Fix access to released memory in clk_debugfs_register_one()
  sh: Fix access to released memory in dwarf_unwinder_cleanup()
  usb: r8a66597-hdc disable interrupts fix
  spi: spi_sh_msiof: Fixed data sampling on the correct edge

13 years agoMerge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
Linus Torvalds [Tue, 2 Feb 2010 20:45:33 +0000 (12:45 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: 64-bit: Detect virtual memory size
  MIPS: AR7: Fix USB slave mem range typo
  MIPS: Alchemy: Fix dbdma ring destruction memory debugcheck.

13 years agoFix 'flush_old_exec()/setup_new_exec()' split
Linus Torvalds [Tue, 2 Feb 2010 20:37:44 +0000 (12:37 -0800)]
Fix 'flush_old_exec()/setup_new_exec()' split

Commit 221af7f87b9 ("Split 'flush_old_exec' into two functions") split
the function at the point of no return - ie right where there were no
more error cases to check.  That made sense from a technical standpoint,
but when we then also combined it with the actual personality setting
going in between flush_old_exec() and setup_new_exec(), it needs to be a
bit more careful.

In particular, we need to make sure that we really flush the old
personality bits in the 'flush' stage, rather than later in the 'setup'
stage, since otherwise we might be flushing the _new_ personality state
that we're just setting up.

So this moves the flags and personality flushing (and 'flush_thread()',
which is the arch-specific function that generally resets lazy FP state
etc) of the old process into flush_old_exec(), so that it doesn't affect
any state that execve() is setting up for the new process environment.

This was reported by Michal Simek as breaking his Microblaze qemu

Reported-and-tested-by: Michal Simek <michal.simek@petalogix.com>
Cc: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
13 years agocfq-iosched: Do not idle on async queues
Vivek Goyal [Tue, 2 Feb 2010 19:45:46 +0000 (20:45 +0100)]
cfq-iosched: Do not idle on async queues

Few weeks back, Shaohua Li had posted similar patch. I am reposting it
with more test results.

This patch does two things.

- Do not idle on async queues.

- It also changes the write queue depth CFQ drives (cfq_may_dispatch()).
  Currently, we seem to driving queue depth of 1 always for WRITES. This is
  true even if there is only one write queue in the system and all the logic
  of infinite queue depth in case of single busy queue as well as slowly
  increasing queue depth based on last delayed sync request does not seem to
  be kicking in at all.

This patch will allow deeper WRITE queue depths (subjected to the other
WRITE queue depth contstraints like cfq_quantum and last delayed sync

Shaohua Li had reported getting more out of his SSD. For me, I have got
one Lun exported from an HP EVA and when pure buffered writes are on, I
can get more out of the system. Following are test results of pure
buffered writes (with end_fsync=1) with vanilla and patched kernel. These
results are average of 3 sets of run with increasing number of threads.

job       Set NR  ReadBW(KB/s)   MaxClat(us)    WriteBW(KB/s)  MaxClat(us)
---       --- --  ------------   -----------    -------------  -----------
bufwfs    3   1   0              0              95349          474141
bufwfs    3   2   0              0              100282         806926
bufwfs    3   4   0              0              109989         2.7301e+06
bufwfs    3   8   0              0              116642         3762231
bufwfs    3   16  0              0              118230         6902970

AVERAGE[bufwfs] [patched kernel]
bufwfs    3   1   0              0              270722         404352
bufwfs    3   2   0              0              206770         1.06552e+06
bufwfs    3   4   0              0              195277         1.62283e+06
bufwfs    3   8   0              0              260960         2.62979e+06
bufwfs    3   16  0              0              299260         1.70731e+06

I also ran buffered writes along with some sequential reads and some
buffered reads going on in the system on a SATA disk because the potential
risk could be that we should not be driving queue depth higher in presence
of sync IO going to keep the max clat low.

With some random and sequential reads going on in the system on one SATA
disk I did not see any significant increase in max clat. So it looks like
other WRITE queue depth control logic is doing its job. Here are the

AVERAGE[brr, bsr, bufw together] [vanilla]
job       Set NR  ReadBW(KB/s)   MaxClat(us)    WriteBW(KB/s)  MaxClat(us)
---       --- --  ------------   -----------    -------------  -----------
brr       3   1   850            546345         0              0
bsr       3   1   14650          729543         0              0
bufw      3   1   0              0              23908          8274517

brr       3   2   981.333        579395         0              0
bsr       3   2   14149.7        1175689        0              0
bufw      3   2   0              0              21921          1.28108e+07

brr       3   4   898.333        1.75527e+06    0              0
bsr       3   4   12230.7        1.40072e+06    0              0
bufw      3   4   0              0              19722.3        2.4901e+07

brr       3   8   900            3160594        0              0
bsr       3   8   9282.33        1.91314e+06    0              0
bufw      3   8   0              0              18789.3        23890622

AVERAGE[brr, bsr, bufw mixed] [patched kernel]
job       Set NR  ReadBW(KB/s)   MaxClat(us)    WriteBW(KB/s)  MaxClat(us)
---       --- --  ------------   -----------    -------------  -----------
brr       3   1   837            417973         0              0
bsr       3   1   14357.7        591275         0              0
bufw      3   1   0              0              24869.7        8910662

brr       3   2   1038.33        543434         0              0
bsr       3   2   13351.3        1205858        0              0
bufw      3   2   0              0              18626.3        13280370

brr       3   4   913            1.86861e+06    0              0
bsr       3   4   12652.3        1430974        0              0
bufw      3   4   0              0              15343.3        2.81305e+07

brr       3   8   890            2.92695e+06    0              0
bsr       3   8   9635.33        1.90244e+06    0              0
bufw      3   8   0              0              17200.3        24424392

So looks like it might make sense to include this patch.


Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
13 years agoMIPS: 64-bit: Detect virtual memory size
Guenter Roeck [Tue, 2 Feb 2010 16:52:20 +0000 (08:52 -0800)]
MIPS: 64-bit: Detect virtual memory size

Linux kernel 2.6.32 and later allocate address space from the top of the
kernel virtual memory address space.

This patch implements virtual memory size detection for 64 bit MIPS CPUs
to avoid resulting crashes.

Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/935/
Reviewed-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
13 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6
David S. Miller [Tue, 2 Feb 2010 17:04:58 +0000 (09:04 -0800)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6

13 years agobe2net: use eq-id to calculate cev-isr reg offset
Sathya Perla [Tue, 2 Feb 2010 15:48:40 +0000 (07:48 -0800)]
be2net: use eq-id to calculate cev-isr reg offset

cev-isr reg offset for each function is better calculated using (any) eq-id
alloted to that function instead of using pci-func number(which
does not work in some configurations...)

Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agosh: Fix access to released memory in clk_debugfs_register_one()
Marek Skuczynski [Sat, 30 Jan 2010 21:29:32 +0000 (22:29 +0100)]
sh: Fix access to released memory in clk_debugfs_register_one()

Signed-off-by: Marek Skuczynski <mareksk7@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
13 years agosh: Fix access to released memory in dwarf_unwinder_cleanup()
Marek Skuczynski [Sat, 30 Jan 2010 21:27:41 +0000 (22:27 +0100)]
sh: Fix access to released memory in dwarf_unwinder_cleanup()

Signed-off-by: Marek Skuczynski <mareksk7@gmail.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
13 years agousb: r8a66597-hdc disable interrupts fix
Magnus Damm [Wed, 27 Jan 2010 07:41:19 +0000 (07:41 +0000)]
usb: r8a66597-hdc disable interrupts fix

This patch improves disable_controller() in the r8a66597-hdc
driver to disable all interrupts and clear status flags. It
also makes sure that disable_controller() is called during
probe(). This fixes the relatively rare case of unexpected
pending interrupts after kexec reboot.

Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
13 years agospi: spi_sh_msiof: Fixed data sampling on the correct edge
Markus Pietrek [Tue, 2 Feb 2010 02:29:15 +0000 (11:29 +0900)]
spi: spi_sh_msiof: Fixed data sampling on the correct edge

The spi_sh_msiof.c driver presently misconfigures REDG and TEDG. TEDG==0
outputs data at the **rising edge** of the clock and REDG==0 samples data
at the **falling edge** of the clock. Therefore for SPI, TEDG must be
equal to REDG, otherwise the last byte received is not sampled in SPI
mode 3.

This brings the driver in line with the SH7723 HW Reference Manual
settings documented in Figures 20.20 and 20.21 ("SPI Clock and data

Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
13 years agosaa7146: stop DMA before de-allocating DMA scatter/gather page buffers
Mauro Carvalho Chehab [Mon, 1 Feb 2010 23:23:46 +0000 (21:23 -0200)]
saa7146: stop DMA before de-allocating DMA scatter/gather page buffers

Thanks-to: Hartmut <e9hack@googlemail.com> for pointing me the problem
and testing the fix.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
13 years agoMerge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6
Russell King [Mon, 1 Feb 2010 20:06:40 +0000 (20:06 +0000)]
Merge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6