* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix 27-rc crash on vsmp due to paravirt during module load
x86, oprofile: BUG scheduling while atomic
AMD IOMMU: protect completion wait loop with iommu lock
AMD IOMMU: set iommu sunc flag after command queuing
Thomas Graf <tgraf@suug.ch>
Tony Luck <tony.luck@intel.com>
Tsuneo Yoshioka <Tsuneo.Yoshioka@f-secure.com>
+Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
+Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
--- /dev/null
+What: /sys/class/gpio/
+Date: July 2008
+KernelVersion: 2.6.27
+Contact: David Brownell <dbrownell@users.sourceforge.net>
+Description:
+
+ As a Kconfig option, individual GPIO signals may be accessed from
+ userspace. GPIOs are only made available to userspace by an explicit
+ "export" operation. If a given GPIO is not claimed for use by
+ kernel code, it may be exported by userspace (and unexported later).
+ Kernel code may export it for complete or partial access.
+
+ GPIOs are identified as they are inside the kernel, using integers in
+ the range 0..INT_MAX. See Documentation/gpio.txt for more information.
+
+ /sys/class/gpio
+ /export ... asks the kernel to export a GPIO to userspace
+ /unexport ... to return a GPIO to the kernel
+ /gpioN ... for each exported GPIO #N
+ /value ... always readable, writes fail for input GPIOs
+ /direction ... r/w as: in, out (default low); write: high, low
+ /gpiochipN ... for each gpiochip; #N is its first GPIO
+ /base ... (r/o) same as N
+ /label ... (r/o) descriptive, not necessarily unique
+ /ngpio ... (r/o) number of GPIOs; numbered N to N + (ngpio - 1)
+
dma_addr_t dma_handle;
dma_handle = pci_map_single(pdev, addr, size, direction);
- if (pci_dma_mapping_error(dma_handle)) {
+ if (pci_dma_mapping_error(pdev, dma_handle)) {
/*
* reduce current DMA mapping usage,
* delay and try again later or
There is an exception to the above. If hotplug functionality is used
to remove all the CPUs that are currently assigned to a cpuset,
-then the kernel will automatically update the cpus_allowed of all
-tasks attached to CPUs in that cpuset to allow all CPUs. When memory
-hotplug functionality for removing Memory Nodes is available, a
-similar exception is expected to apply there as well. In general,
-the kernel prefers to violate cpuset placement, over starving a task
-that has had all its allowed CPUs or Memory Nodes taken offline. User
-code should reconfigure cpusets to only refer to online CPUs and Memory
-Nodes when using hotplug to add or remove such resources.
+then all the tasks in that cpuset will be moved to the nearest ancestor
+with non-empty cpus. But the moving of some (or all) tasks might fail if
+cpuset is bound with another cgroup subsystem which has some restrictions
+on task attaching. In this failing case, those tasks will stay
+in the original cpuset, and the kernel will automatically update
+their cpus_allowed to allow all online CPUs. When memory hotplug
+functionality for removing Memory Nodes is available, a similar exception
+is expected to apply there as well. In general, the kernel prefers to
+violate cpuset placement, over starving a task that has had all
+its allowed CPUs or Memory Nodes taken offline.
There is a second exception to the above. GFP_ATOMIC requests are
kernel internal allocations that must be satisfied, immediately.
controlled by a kernel/module/sysfs/sysctl parameter.
Who: Krzysztof Piotr Oledzki <ole@ans.pl>
+---------------------------
+
+What: ide-scsi (BLK_DEV_IDESCSI)
+When: 2.6.29
+Why: The 2.6 kernel supports direct writing to ide CD drives, which
+ eliminates the need for ide-scsi. The new method is more
+ efficient in every way.
+Who: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
- (bit 1) anonymous shared memory
- (bit 2) file-backed private memory
- (bit 3) file-backed shared memory
+ - (bit 4) ELF header pages in file-backed private memory areas (it is
+ effective only if the bit 2 is cleared)
Note that MMIO pages such as frame buffer are never dumped and vDSO pages
are always dumped regardless of the bitmask status.
softlockup_thresh:
-This value can be used to lower the softlockup tolerance
-threshold. The default threshold is 10s. If a cpu is locked up
-for 10s, the kernel complains. Valid values are 1-60s.
+This value can be used to lower the softlockup tolerance threshold. The
+default threshold is 60 seconds. If a cpu is locked up for 60 seconds,
+the kernel complains. Valid values are 1-60 seconds. Setting this
+tunable to zero will disable the softlockup detection altogether.
==============================================================
S: Supported
ACPI WMI DRIVER
-P: Carlos Corbacho
-M: carlos@strangeworlds.co.uk
-L: linux-acpi@vger.kernel.org
-W: http://www.lesswatts.org/projects/acpi/
-S: Maintained
+P: Carlos Corbacho
+M: carlos@strangeworlds.co.uk
+L: linux-acpi@vger.kernel.org
+W: http://www.lesswatts.org/projects/acpi/
+S: Maintained
AD1889 ALSA SOUND DRIVER
-P: Kyle McMartin
-M: kyle@mcmartin.ca
-P: Thibaut Varene
-M: T-Bone@parisc-linux.org
-W: http://wiki.parisc-linux.org/AD1889
-L: linux-parisc@vger.kernel.org
-S: Maintained
+P: Kyle McMartin
+M: kyle@mcmartin.ca
+P: Thibaut Varene
+M: T-Bone@parisc-linux.org
+W: http://wiki.parisc-linux.org/AD1889
+L: linux-parisc@vger.kernel.org
+S: Maintained
ADM1025 HARDWARE MONITOR DRIVER
P: Jean Delvare
S: Maintained
ARM/ATMEL AT91RM9200 ARM ARCHITECTURE
-P: Andrew Victor
-M: linux@maxim.org.za
-L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
-W: http://maxim.org.za/at91_26.html
-S: Maintained
+P: Andrew Victor
+M: linux@maxim.org.za
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+W: http://maxim.org.za/at91_26.html
+S: Maintained
ARM/CIRRUS LOGIC EP93XX ARM ARCHITECTURE
P: Lennert Buytenhek
S: Maintained
ARM/HP JORNADA 7XX MACHINE SUPPORT
-P: Kristoffer Ericson
-M: kristoffer.ericson@gmail.com
-W: www.jlime.com
-S: Maintained
+P: Kristoffer Ericson
+M: kristoffer.ericson@gmail.com
+W: www.jlime.com
+S: Maintained
ARM/INTEL IOP32X ARM ARCHITECTURE
P: Lennert Buytenhek
S: Maintained
CAFE CMOS INTEGRATED CAMERA CONTROLLER DRIVER
-P: Jonathan Corbet
+P: Jonathan Corbet
M: corbet@lwn.net
L: video4linux-list@redhat.com
S: Maintained
M: Eng.Linux@digi.com
L: Eng.Linux@digi.com
W: http://www.digi.com
-S: Orphaned
+S: Orphan
DIRECTORY NOTIFICATION
P: Stephen Rothwell
S: Supported
DOCUMENTATION (/Documentation directory)
-P: Michael Kerrisk
-M: mtk.manpages@gmail.com
-P: Randy Dunlap
-M: rdunlap@xenotime.net
-L: linux-doc@vger.kernel.org
-S: Maintained
+P: Michael Kerrisk
+M: mtk.manpages@gmail.com
+P: Randy Dunlap
+M: rdunlap@xenotime.net
+L: linux-doc@vger.kernel.org
+S: Maintained
DOUBLETALK DRIVER
P: James R. Van Zandt
DVB SUBSYSTEM AND DRIVERS
P: LinuxTV.org Project
M: v4l-dvb-maintainer@linuxtv.org
-L: linux-dvb@linuxtv.org (subscription required)
+L: linux-dvb@linuxtv.org (subscription required)
W: http://linuxtv.org/
T: git kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb.git
S: Maintained
P: Rik Faith
M: faith@cs.unc.edu
L: linux-scsi@vger.kernel.org
-S: Odd fixes (e.g., new signatures)
+S: Odd Fixes (e.g., new signatures)
GDT SCSI DISK ARRAY CONTROLLER DRIVER
P: Achim Leubner
HARDWARE MONITORING
L: lm-sensors@lm-sensors.org
W: http://www.lm-sensors.org/
-S: Orphaned
+S: Orphan
HARDWARE RANDOM NUMBER GENERATOR CORE
-S: Orphaned
+S: Orphan
HARD DRIVE ACTIVE PROTECTION SYSTEM (HDAPS) DRIVER
P: Robert Love
P: Sean Hefty
M: sean.hefty@intel.com
P: Hal Rosenstock
-M: hal.rosenstock@gmail.com
+M: hal.rosenstock@gmail.com
L: general@lists.openfabrics.org
W: http://www.openib.org/
T: git kernel.org:/pub/scm/linux/kernel/git/roland/infiniband.git
MARVELL YUKON / SYSKONNECT DRIVER
P: Mirko Lindner
-M: mlindner@syskonnect.de
+M: mlindner@syskonnect.de
P: Ralph Roesler
-M: rroesler@syskonnect.de
-W: http://www.syskonnect.com
-S: Supported
+M: rroesler@syskonnect.de
+W: http://www.syskonnect.com
+S: Supported
MAN-PAGES: MANUAL PAGES FOR LINUX -- Sections 2, 3, 4, 5, and 7
P: Michael Kerrisk
M: mtk.manpages@gmail.com
-W: http://www.kernel.org/doc/man-pages
-S: Supported
+W: http://www.kernel.org/doc/man-pages
+S: Supported
MARVELL LIBERTAS WIRELESS DRIVER
P: Dan Williams
MEGARAID SCSI DRIVERS
P: Neela Syam Kolli
M: megaraidlinux@lsi.com
-S: linux-scsi@vger.kernel.org
+L: linux-scsi@vger.kernel.org
W: http://megaraid.lsilogic.com
S: Maintained
P: David Brownell
M: dbrownell@users.sourceforge.net
L: linux-kernel@vger.kernel.org
-S: Odd fixes
+S: Odd Fixes
MULTISOUND SOUND DRIVER
P: Andrew Veliath
S: Maintained
MUSB MULTIPOINT HIGH SPEED DUAL-ROLE CONTROLLER
-P: Felipe Balbi
-M: felipe.balbi@nokia.com
-L: linux-usb@vger.kernel.org
-S: Maintained
+P: Felipe Balbi
+M: felipe.balbi@nokia.com
+L: linux-usb@vger.kernel.org
+S: Maintained
MYRICOM MYRI-10G 10GbE DRIVER (MYRI10GE)
P: Andrew Gallatin
S: Supported
NATSEMI ETHERNET DRIVER (DP8381x)
-P: Tim Hockin
+P: Tim Hockin
M: thockin@hockin.org
S: Maintained
S: Maintained
OMNIVISION OV7670 SENSOR DRIVER
-P: Jonathan Corbet
+P: Jonathan Corbet
M: corbet@lwn.net
L: video4linux-list@redhat.com
S: Maintained
S: Supported
PCI HOTPLUG CORE
-P: Kristen Carlson Accardi
+P: Kristen Carlson Accardi
M: kristen.c.accardi@intel.com
S: Supported
P: Eric Paris
M: eparis@parisplace.org
L: linux-kernel@vger.kernel.org (kernel issues)
-L: selinux@tycho.nsa.gov (subscribers-only, general discussion)
+L: selinux@tycho.nsa.gov (subscribers-only, general discussion)
W: http://www.nsa.gov/selinux
S: Supported
S: Maintained
SOC-CAMERA V4L2 SUBSYSTEM
-P: Guennadi Liakhovetski
-M: g.liakhovetski@gmx.de
-L: video4linux-list@redhat.com
-S: Maintained
+P: Guennadi Liakhovetski
+M: g.liakhovetski@gmx.de
+L: video4linux-list@redhat.com
+S: Maintained
SOFTWARE RAID (Multiple Disks) SUPPORT
P: Ingo Molnar
SOUND - SOC LAYER / DYNAMIC AUDIO POWER MANAGEMENT
P: Liam Girdwood
-M: liam.girdwood@wolfsonmicro.com
+M: lrg@slimlogic.co.uk
P: Mark Brown
M: broonie@opensource.wolfsonmicro.com
T: git opensource.wolfsonmicro.com/linux-2.6-asoc
L: alsa-devel@alsa-project.org (subscribers-only)
+W: http://alsa-project.org/main/index.php/ASoC
S: Supported
SPI SUBSYSTEM
STARMODE RADIO IP (STRIP) PROTOCOL DRIVER
W: http://mosquitonet.Stanford.EDU/strip.html
-S: Unsupported ?
+S: Orphan
STRADIS MPEG-2 DECODER DRIVER
P: Nathan Laredo
S: Maintained
TI FLASH MEDIA INTERFACE DRIVER
-P: Alex Dubov
-M: oakad@yahoo.com
-S: Maintained
+P: Alex Dubov
+M: oakad@yahoo.com
+S: Maintained
TI OMAP MMC INTERFACE DRIVER
P: Carlos Aguiar, Anderson Briglia and Syed Khasim
P: Pete Zaitcev
M: zaitcev@redhat.com
L: linux-kernel@vger.kernel.org
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Supported
USB CDC ETHERNET DRIVER
P: Greg Kroah-Hartman
M: greg@kroah.com
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Maintained
W: http://www.kroah.com/linux-usb/
USB EHCI DRIVER
P: David Brownell
M: dbrownell@users.sourceforge.net
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Odd Fixes
USB ET61X[12]51 DRIVER
P: Luca Risolia
M: luca.risolia@studio.unibo.it
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
L: video4linux-list@redhat.com
W: http://www.linux-projects.org
S: Maintained
USB GADGET/PERIPHERAL SUBSYSTEM
P: David Brownell
M: dbrownell@users.sourceforge.net
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
W: http://www.linux-usb.org/gadget
S: Maintained
USB HID/HIDBP DRIVERS (USB KEYBOARDS, MICE, REMOTE CONTROLS, ...)
P: Jiri Kosina
M: jkosina@suse.cz
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
T: git kernel.org:/pub/scm/linux/kernel/git/jikos/hid.git
S: Maintained
USB ISP116X DRIVER
P: Olav Kongas
M: ok@artecdesign.ee
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Maintained
USB KAWASAKI LSI DRIVER
P: Oliver Neukum
M: oliver@neukum.name
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Maintained
USB MASS STORAGE DRIVER
P: Matthew Dharm
M: mdharm-usb@one-eyed-alien.net
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
L: usb-storage@lists.one-eyed-alien.net
S: Maintained
W: http://www.one-eyed-alien.net/~mdharm/linux-usb/
USB OHCI DRIVER
P: David Brownell
M: dbrownell@users.sourceforge.net
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Odd Fixes
USB OPTION-CARD DRIVER
P: Matthias Urlichs
M: smurf@smurf.noris.de
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Maintained
USB OV511 DRIVER
P: Mark McClelland
M: mmcclell@bigfoot.com
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
W: http://alpha.dyndns.org/ov511/
S: Maintained
USB PEGASUS DRIVER
P: Petko Manolov
M: petkan@users.sourceforge.net
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
L: netdev@vger.kernel.org
W: http://pegasus2.sourceforge.net/
S: Maintained
USB PRINTER DRIVER (usblp)
P: Pete Zaitcev
M: zaitcev@redhat.com
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Supported
USB RTL8150 DRIVER
P: Petko Manolov
M: petkan@users.sourceforge.net
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
L: netdev@vger.kernel.org
W: http://pegasus2.sourceforge.net/
S: Maintained
USB SE401 DRIVER
P: Jeroen Vreeken
M: pe1rxq@amsat.org
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
W: http://www.chello.nl/~j.vreeken/se401/
S: Maintained
USB SERIAL BELKIN F5U103 DRIVER
P: William Greathouse
M: wgreathouse@smva.com
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Maintained
USB SERIAL CYPRESS M8 DRIVER
P: Lonnie Mendez
M: dignome@gmail.com
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Maintained
W: http://geocities.com/i0xox0i
W: http://firstlight.net/cvs
P: Peter Berger and Al Borchers
M: pberger@brimson.com
M: alborchers@steinerpoint.com
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Maintained
USB SERIAL DRIVER
P: Greg Kroah-Hartman
M: gregkh@suse.de
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Supported
USB SERIAL EMPEG EMPEG-CAR MARK I/II DRIVER
P: Gary Brubaker
M: xavyer@ix.netcom.com
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Maintained
USB SERIAL KEYSPAN DRIVER
P: Greg Kroah-Hartman
M: greg@kroah.com
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
W: http://www.kroah.com/linux/
S: Maintained
USB SERIAL WHITEHEAT DRIVER
P: Support Department
M: support@connecttech.com
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
W: http://www.connecttech.com
S: Supported
USB SN9C1xx DRIVER
P: Luca Risolia
M: luca.risolia@studio.unibo.it
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
L: video4linux-list@redhat.com
W: http://www.linux-projects.org
S: Maintained
USB SUBSYSTEM
P: Greg Kroah-Hartman
M: gregkh@suse.de
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
W: http://www.linux-usb.org
T: quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/
S: Supported
USB UHCI DRIVER
P: Alan Stern
M: stern@rowland.harvard.edu
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
S: Maintained
USB "USBNET" DRIVER FRAMEWORK
USB VIDEO CLASS
P: Laurent Pinchart
M: laurent.pinchart@skynet.be
-L: linx-uvc-devel@berlios.de
+L: linux-uvc-devel@lists.berlios.de
L: video4linux-list@redhat.com
W: http://linux-uvc.berlios.de
S: Maintained
USB W996[87]CF DRIVER
P: Luca Risolia
M: luca.risolia@studio.unibo.it
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
L: video4linux-list@redhat.com
W: http://www.linux-projects.org
S: Maintained
USB ZC0301 DRIVER
P: Luca Risolia
M: luca.risolia@studio.unibo.it
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
L: video4linux-list@redhat.com
W: http://www.linux-projects.org
S: Maintained
USB ZD1201 DRIVER
P: Jeroen Vreeken
M: pe1rxq@amsat.org
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
W: http://linux-lc100020.sourceforge.net
S: Maintained
USB ZR364XX DRIVER
P: Antoine Jacquet
M: royale@zerezo.com
-L: linux-usb@vger.kernel.org
+L: linux-usb@vger.kernel.org
L: video4linux-list@redhat.com
W: http://royale.zerezo.com/zr364xx/
S: Maintained
VERSION = 2
PATCHLEVEL = 6
SUBLEVEL = 27
-EXTRAVERSION = -rc6
+EXTRAVERSION = -rc7
NAME = Rotary Wombat
# *DOCUMENTATION*
* The networking and block device layers use this boolean for bounce
* buffer decisions.
*/
-#define PCI_DMA_BUS_IS_PHYS (0)
+#define PCI_DMA_BUS_IS_PHYS (1)
/*
* Whether pci_unmap_{single,page} is a nop depends upon the
{
u32 epcpr, ptcmd, ptstat, pdstat, pdctl1, mdstat, mdctl, mdstat_mask;
- if (id < 0)
- return;
-
mdctl = davinci_readl(DAVINCI_PWR_SLEEP_CNTRL_BASE + MDCTL + 4 * id);
if (enable)
mdctl |= 0x00000003; /* Enable Module */
};
static struct imxuart_platform_data uart_pdata = {
- .flags = 0,
+ .flags = IMXUART_HAVE_RTSCTS,
};
static struct platform_device *devices[] __initdata = {
#include <asm/mach/sharpsl_param.h>
#include "generic.h"
+#include "clock.h"
#include "devices.h"
static unsigned long tosa_pin_config[] = {
.wakeup = 1,
.active_low = 1,
},
+ {
+ .type = EV_SW,
+ .code = SW_HEADPHONE_INSERT,
+ .gpio = TOSA_GPIO_EAR_IN,
+ .desc = "HeadPhone insert",
+ .active_low = 1,
+ .debounce_interval = 300,
+ },
};
static struct gpio_keys_platform_data tosa_gpio_keys_platform_data = {
pxa_set_i2c_info(NULL);
platform_scoop_config = &tosa_pcmcia_config;
+ clk_add_alias("CLK_CK3P6MI", &tc6393xb_device.dev, "GPIO11_CLK", NULL);
+
platform_add_devices(devices, ARRAY_SIZE(devices));
}
/*
* arch/arm/mach-sa1100/include/mach/jornada720.h
*
- * This file contains SSP/MCU communication definitions for HP Jornada 710/720/728
+ * SSP/MCU communication definitions for HP Jornada 710/720/728
*
- * Copyright (C) 2007 Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
- * Copyright (C) 2000 John Ankcorn <jca@lcs.mit.edu>
+ * Copyright 2007,2008 Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
+ * Copyright 2000 John Ankcorn <jca@lcs.mit.edu>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
#define PWMOFF 0xDF
#define TXDUMMY 0x11
#define ERRORCODE 0x00
+
+extern void jornada_ssp_start(void);
+extern void jornada_ssp_end(void);
+extern int jornada_ssp_inout(u8 byte);
+extern int jornada_ssp_byte(u8 byte);
#include <linux/slab.h>
#include <mach/hardware.h>
-#include <asm/hardware/ssp.h>
#include <mach/jornada720.h>
+#include <asm/hardware/ssp.h>
static DEFINE_SPINLOCK(jornada_ssp_lock);
static unsigned long jornada_ssp_flags;
* jornada_ssp_start - enable mcu
*
*/
-int jornada_ssp_start()
+void jornada_ssp_start(void)
{
spin_lock_irqsave(&jornada_ssp_lock, jornada_ssp_flags);
GPCR = GPIO_GPIO25;
udelay(50);
- return 0;
+ return;
};
EXPORT_SYMBOL(jornada_ssp_start);
* jornada_ssp_end - disable mcu and turn off lock
*
*/
-int jornada_ssp_end()
+void jornada_ssp_end(void)
{
GPSR = GPIO_GPIO25;
spin_unlock_irqrestore(&jornada_ssp_lock, jornada_ssp_flags);
- return 0;
+ return;
};
EXPORT_SYMBOL(jornada_ssp_end);
#include <mach/tc.h>
#include <mach/board.h>
+#include <mach/mmc.h>
#include <mach/mux.h>
#include <mach/gpio.h>
#include <mach/menelaus.h>
/*-------------------------------------------------------------------------*/
-#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \
+ defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
-#ifdef CONFIG_ARCH_OMAP24XX
+#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
#define OMAP_MMC1_BASE 0x4809c000
-#define OMAP_MMC1_INT INT_24XX_MMC_IRQ
+#define OMAP_MMC1_END (OMAP_MMC1_BASE + 0x1fc)
+#define OMAP_MMC1_INT INT_24XX_MMC_IRQ
+
+#define OMAP_MMC2_BASE 0x480b4000
+#define OMAP_MMC2_END (OMAP_MMC2_BASE + 0x1fc)
+#define OMAP_MMC2_INT INT_24XX_MMC2_IRQ
+
#else
+
#define OMAP_MMC1_BASE 0xfffb7800
+#define OMAP_MMC1_END (OMAP_MMC1_BASE + 0x7f)
#define OMAP_MMC1_INT INT_MMC
-#endif
+
#define OMAP_MMC2_BASE 0xfffb7c00 /* omap16xx only */
+#define OMAP_MMC2_END (OMAP_MMC2_BASE + 0x7f)
+#define OMAP_MMC2_INT INT_1610_MMC2
+
+#endif
-static struct omap_mmc_conf mmc1_conf;
+static struct omap_mmc_platform_data mmc1_data;
static u64 mmc1_dmamask = 0xffffffff;
static struct resource mmc1_resources[] = {
{
.start = OMAP_MMC1_BASE,
- .end = OMAP_MMC1_BASE + 0x7f,
+ .end = OMAP_MMC1_END,
.flags = IORESOURCE_MEM,
},
{
.id = 1,
.dev = {
.dma_mask = &mmc1_dmamask,
- .platform_data = &mmc1_conf,
+ .platform_data = &mmc1_data,
},
.num_resources = ARRAY_SIZE(mmc1_resources),
.resource = mmc1_resources,
};
-#ifdef CONFIG_ARCH_OMAP16XX
+#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \
+ defined(CONFIG_ARCH_OMAP34XX)
-static struct omap_mmc_conf mmc2_conf;
+static struct omap_mmc_platform_data mmc2_data;
static u64 mmc2_dmamask = 0xffffffff;
static struct resource mmc2_resources[] = {
{
.start = OMAP_MMC2_BASE,
- .end = OMAP_MMC2_BASE + 0x7f,
+ .end = OMAP_MMC2_END,
.flags = IORESOURCE_MEM,
},
{
- .start = INT_1610_MMC2,
+ .start = OMAP_MMC2_INT,
.flags = IORESOURCE_IRQ,
},
};
.id = 2,
.dev = {
.dma_mask = &mmc2_dmamask,
- .platform_data = &mmc2_conf,
+ .platform_data = &mmc2_data,
},
.num_resources = ARRAY_SIZE(mmc2_resources),
.resource = mmc2_resources,
};
#endif
-static void __init omap_init_mmc(void)
+static inline void omap_init_mmc_conf(const struct omap_mmc_config *mmc_conf)
{
- const struct omap_mmc_config *mmc_conf;
- const struct omap_mmc_conf *mmc;
-
- /* NOTE: assumes MMC was never (wrongly) enabled */
- mmc_conf = omap_get_config(OMAP_TAG_MMC, struct omap_mmc_config);
- if (!mmc_conf)
+ if (cpu_is_omap2430() || cpu_is_omap34xx())
return;
- /* block 1 is always available and has just one pinout option */
- mmc = &mmc_conf->mmc[0];
- if (mmc->enabled) {
+ if (mmc_conf->mmc[0].enabled) {
if (cpu_is_omap24xx()) {
omap_cfg_reg(H18_24XX_MMC_CMD);
omap_cfg_reg(H15_24XX_MMC_CLKI);
omap_cfg_reg(P20_1710_MMC_DATDIR0);
}
}
- if (mmc->wire4) {
+ if (mmc_conf->mmc[0].wire4) {
if (cpu_is_omap24xx()) {
omap_cfg_reg(H14_24XX_MMC_DAT1);
omap_cfg_reg(E19_24XX_MMC_DAT2);
} else {
omap_cfg_reg(MMC_DAT1);
/* NOTE: DAT2 can be on W10 (here) or M15 */
- if (!mmc->nomux)
+ if (!mmc_conf->mmc[0].nomux)
omap_cfg_reg(MMC_DAT2);
omap_cfg_reg(MMC_DAT3);
}
}
- mmc1_conf = *mmc;
- (void) platform_device_register(&mmc_omap_device1);
}
#ifdef CONFIG_ARCH_OMAP16XX
/* block 2 is on newer chips, and has many pinout options */
- mmc = &mmc_conf->mmc[1];
- if (mmc->enabled) {
- if (!mmc->nomux) {
+ if (mmc_conf->mmc[1].enabled) {
+ if (!mmc_conf->mmc[1].nomux) {
omap_cfg_reg(Y8_1610_MMC2_CMD);
omap_cfg_reg(Y10_1610_MMC2_CLK);
omap_cfg_reg(R18_1610_MMC2_CLKIN);
omap_cfg_reg(W8_1610_MMC2_DAT0);
- if (mmc->wire4) {
+ if (mmc_conf->mmc[1].wire4) {
omap_cfg_reg(V8_1610_MMC2_DAT1);
omap_cfg_reg(W15_1610_MMC2_DAT2);
omap_cfg_reg(R10_1610_MMC2_DAT3);
if (cpu_is_omap1710())
omap_writel(omap_readl(MOD_CONF_CTRL_1) | (1 << 24),
MOD_CONF_CTRL_1);
- mmc2_conf = *mmc;
+ }
+#endif
+}
+
+static void __init omap_init_mmc(void)
+{
+ const struct omap_mmc_config *mmc_conf;
+
+ /* NOTE: assumes MMC was never (wrongly) enabled */
+ mmc_conf = omap_get_config(OMAP_TAG_MMC, struct omap_mmc_config);
+ if (!mmc_conf)
+ return;
+
+ omap_init_mmc_conf(mmc_conf);
+
+ if (mmc_conf->mmc[0].enabled) {
+ mmc1_data.conf = mmc_conf->mmc[0];
+ (void) platform_device_register(&mmc_omap_device1);
+ }
+
+#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \
+ defined(CONFIG_ARCH_OMAP34XX)
+ if (mmc_conf->mmc[1].enabled) {
+ mmc2_data.conf = mmc_conf->mmc[1];
(void) platform_device_register(&mmc_omap_device2);
}
#endif
- return;
}
+
+void omap_set_mmc_info(int host, const struct omap_mmc_platform_data *info)
+{
+ switch (host) {
+ case 1:
+ mmc1_data = *info;
+ break;
+#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \
+ defined(CONFIG_ARCH_OMAP34XX)
+ case 2:
+ mmc2_data = *info;
+ break;
+#endif
+ default:
+ BUG();
+ }
+}
+
#else
static inline void omap_init_mmc(void) {}
+void omap_set_mmc_info(int host, const struct omap_mmc_platform_data *info) {}
#endif
/*-------------------------------------------------------------------------*/
#ifdef CONFIG_BOARD_ATSTK100X_SPI1
at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
#endif
-#ifndef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM
+#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
at32_add_device_mci(0, MCI_PDATA);
#endif
#ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM
--- /dev/null
+uImage
+uImage.srec
+vmlinux.cso
+sfdwarf.log
--- /dev/null
+vmlinux.lds
EXPORT_SYMBOL(find_next_zero_bit);
EXPORT_SYMBOL(find_first_bit);
EXPORT_SYMBOL(find_next_bit);
+EXPORT_SYMBOL(generic_find_next_le_bit);
EXPORT_SYMBOL(generic_find_next_zero_le_bit);
/* I/O primitives (lib/io-*.S) */
rcall sys_epoll_pwait
sub sp, -4
popm pc
+
+ .global __sys_sync_file_range
+ .type __sys_sync_file_range,@function
+__sys_sync_file_range:
+ pushm lr
+ st.w --sp, ARG6
+ rcall sys_sync_file_range
+ sub sp, -4
+ popm pc
.long sys_set_robust_list
.long sys_get_robust_list /* 260 */
.long __sys_splice
- .long sys_sync_file_range
+ .long __sys_sync_file_range
.long sys_tee
.long sys_vmsplice
.long __sys_epoll_pwait /* 265 */
switch (ret) {
case NOTIFY_OK:
case NOTIFY_STOP:
- return;
+ break;
case NOTIFY_BAD:
die("Fatal Non-Maskable Interrupt", regs, SIGINT);
default:
+ printk(KERN_ALERT "Got NMI, but nobody cared. Disabling...\n");
+ nmi_disable();
break;
}
-
- printk(KERN_ALERT "Got NMI, but nobody cared. Disabling...\n");
- nmi_disable();
+ nmi_exit();
}
asmlinkage void do_critical_exception(unsigned long ecr, struct pt_regs *regs)
brgt 1b
retal r11
+ENTRY(generic_find_next_le_bit)
+ lsr r8, r10, 5
+ sub r9, r11, r10
+ retle r11
+
+ lsl r8, 2
+ add r12, r8
+ andl r10, 31, COH
+ breq 1f
+
+ /* offset is not word-aligned. Handle the first (32 - r10) bits */
+ ldswp.w r8, r12[0]
+ sub r12, -4
+ lsr r8, r8, r10
+ brne .L_found
+
+ /* r9 = r9 - (32 - r10) = r9 + r10 - 32 */
+ add r9, r10
+ sub r9, 32
+ retle r11
+
+ /* Main loop. offset must be word-aligned */
+1: ldswp.w r8, r12[0]
+ cp.w r8, 0
+ brne .L_found
+ sub r12, -4
+ sub r9, 32
+ brgt 1b
+ retal r11
+
ENTRY(generic_find_next_zero_le_bit)
lsr r8, r10, 5
sub r9, r11, r10
} \
} while (0)
+/*
+ * format for entries in the Global Offset Table
+ */
+struct got_entry {
+ uint64_t val;
+};
+
+/*
+ * Layout of the Function Descriptor
+ */
+struct fdesc {
+ uint64_t ip;
+ uint64_t gp;
+};
+
#endif /* _ASM_IA64_ELF_H */
* David Mosberger-Tang <davidm@hpl.hp.com>
*/
+#include <linux/elf.h>
+#include <linux/uaccess.h>
#include <asm-generic/sections.h>
extern char __per_cpu_start[], __per_cpu_end[], __phys_per_cpu_start[];
extern char __start_ivt_text[], __end_ivt_text[];
#undef dereference_function_descriptor
-void *dereference_function_descriptor(void *);
+static inline void *dereference_function_descriptor(void *ptr)
+{
+ struct fdesc *desc = ptr;
+ void *p;
+
+ if (!probe_kernel_address(&desc->ip, p))
+ ptr = p;
+ return ptr;
+}
+
#endif /* _ASM_IA64_SECTIONS_H */
* until the transfer is complete. In order to get the asynch
* version of bte_copy, you must perform this check yourself.
*/
-#define BTE_UNALIGNED_COPY(src, dest, len, mode) \
- (((len & L1_CACHE_MASK) || (src & L1_CACHE_MASK) || \
- (dest & L1_CACHE_MASK)) ? \
- bte_unaligned_copy(src, dest, len, mode) : \
+#define BTE_UNALIGNED_COPY(src, dest, len, mode) \
+ (((len & (L1_CACHE_BYTES - 1)) || \
+ (src & (L1_CACHE_BYTES - 1)) || \
+ (dest & (L1_CACHE_BYTES - 1))) ? \
+ bte_unaligned_copy(src, dest, len, mode) : \
bte_copy(src, dest, len, mode, NULL))
if (md->attribute & EFI_MEMORY_WP) {
name = "System ROM";
flags |= IORESOURCE_READONLY;
- } else {
+ } else if (md->attribute == EFI_MEMORY_UC)
+ name = "Uncached RAM";
+ else
name = "System RAM";
- }
break;
case EFI_ACPI_MEMORY_NVS:
#include <linux/elf.h>
#include <linux/moduleloader.h>
#include <linux/string.h>
-#include <linux/uaccess.h>
#include <linux/vmalloc.h>
#include <asm/patch.h>
-#include <asm/sections.h>
#include <asm/unaligned.h>
#define ARCH_MODULE_DEBUG 0
#undef N
-struct got_entry {
- uint64_t val;
-};
-
-struct fdesc {
- uint64_t ip;
- uint64_t gp;
-};
-
/* Opaque struct for insns, to protect against derefs. */
struct insn;
if (mod->arch.core_unw_table)
unw_remove_unwind_table(mod->arch.core_unw_table);
}
-
-void *dereference_function_descriptor(void *ptr)
-{
- struct fdesc *desc = ptr;
- void *p;
-
- if (!probe_kernel_address(&desc->ip, p))
- ptr = p;
- return ptr;
-}
ia64_mca_init();
platform_setup(cmdline_p);
+#ifndef CONFIG_IA64_HP_SIM
check_sal_cache_flush();
+#endif
paging_init();
}
return -EBUSY;
}
- cpu_clear(cpu, cpu_online_map);
-
if (migrate_platform_irqs(cpu)) {
cpu_set(cpu, cpu_online_map);
return (-EBUSY);
}
remove_siblinginfo(cpu);
- cpu_clear(cpu, cpu_online_map);
fixup_irqs();
+ cpu_clear(cpu, cpu_online_map);
local_flush_tlb_all();
cpu_clear(cpu, cpu_callin_map);
return 0;
#include <asm/cacheflush.h>
#include <asm/div64.h>
#include <asm/tlb.h>
+#include <asm/elf.h>
#include "misc.h"
#include "vti.h"
{ NULL }
};
-
-struct fdesc{
- unsigned long ip;
- unsigned long gp;
-};
-
static void kvm_flush_icache(unsigned long start, unsigned long len)
{
int l;
entry = find_next_zero_bit(map, mapsize, last_entry);
}
- if (entry > mapsize)
+ if (entry > mapsize) {
+ kfree(ca_dmamap);
goto map_return;
+ }
for (i = 0; i < entries; i++)
set_bit(entry + i, map);
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:00 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
CONFIG_ZORRO_NAMES=y
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
#
# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
+CONFIG_IDE_ATAPI=y
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDEDOUBLER=y
CONFIG_BLK_DEV_BUDDHA=y
# CONFIG_BLK_DEV_IDEDMA is not set
-# CONFIG_BLK_DEV_HD_ONLY is not set
-# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
CONFIG_GVP11_SCSI=y
CONFIG_SCSI_A4000T=y
CONFIG_SCSI_ZORRO7XX=y
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
CONFIG_SOUND=m
CONFIG_DMASOUND_PAULA=m
CONFIG_DMASOUND=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
-CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=m
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:01 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_PROC_HARDWARE=y
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
CONFIG_SCSI_LOWLEVEL=y
CONFIG_ISCSI_TCP=m
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
# CONFIG_PHYLIB is not set
CONFIG_NET_ETHERNET=y
# CONFIG_MII is not set
-CONFIG_APOLLO_ELPLUS=y
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
CONFIG_LOGO_LINUX_MONO=y
# CONFIG_LOGO_LINUX_VGA16 is not set
# CONFIG_LOGO_LINUX_CLUT224 is not set
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:02 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_PROC_HARDWARE=y
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
#
# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
+CONFIG_IDE_ATAPI=y
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_BLK_DEV_PLATFORM is not set
CONFIG_BLK_DEV_FALCON_IDE=y
# CONFIG_BLK_DEV_IDEDMA is not set
-# CONFIG_BLK_DEV_HD_ONLY is not set
-# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
CONFIG_ATARI_SCSI=y
# CONFIG_ATARI_SCSI_TOSHIBA_DELAY is not set
# CONFIG_ATARI_SCSI_RESET_BOOT is not set
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
CONFIG_SOUND=m
CONFIG_DMASOUND_ATARI=m
CONFIG_DMASOUND=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set
# Character devices
#
CONFIG_ATARI_MFPSER=m
-CONFIG_ATARI_SCC=y
-CONFIG_ATARI_SCC_DMA=y
CONFIG_ATARI_MIDI=m
CONFIG_ATARI_DSP56K=m
-# CONFIG_SERIAL_CONSOLE is not set
#
# File systems
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
-# CONFIG_EXT4DEV_FS is not set
+CONFIG_EXT4DEV_FS=y
+# CONFIG_EXT4DEV_FS_XATTR is not set
CONFIG_JBD=y
+CONFIG_JBD2=y
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
-CONFIG_SUNRPC_BIND34=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=y
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:03 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_PROC_HARDWARE=y
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
CONFIG_53C700_BE_BUS=y
# CONFIG_SCSI_DEBUG is not set
CONFIG_BVME6000_SCSI=y
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=m
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:04 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_PROC_HARDWARE=y
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
CONFIG_SCSI_LOWLEVEL=y
CONFIG_ISCSI_TCP=m
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:06 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_PROC_HARDWARE=y
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
#
# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
+CONFIG_IDE_ATAPI=y
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_BLK_DEV_PLATFORM is not set
CONFIG_BLK_DEV_MAC_IDE=y
# CONFIG_BLK_DEV_IDEDMA is not set
-# CONFIG_BLK_DEV_HD_ONLY is not set
-# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
# CONFIG_SCSI_DEBUG is not set
CONFIG_MAC_SCSI=y
CONFIG_SCSI_MAC_ESP=y
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_MACINTOSH_DRIVERS=y
CONFIG_INPUT_ADBHID=y
CONFIG_MAC_EMUMOUSEBTN=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_LOGO_MAC_CLUT224=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
-CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=m
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:07 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
CONFIG_ZORRO_NAMES=y
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
#
# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
+CONFIG_IDE_ATAPI=y
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_MAC_IDE=y
CONFIG_BLK_DEV_Q40IDE=y
# CONFIG_BLK_DEV_IDEDMA is not set
-# CONFIG_BLK_DEV_HD_ONLY is not set
-# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
CONFIG_MVME16x_SCSI=y
CONFIG_BVME6000_SCSI=y
CONFIG_SUN3X_ESP=y
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_MACINTOSH_DRIVERS=y
CONFIG_INPUT_ADBHID=y
CONFIG_MAC_EMUMOUSEBTN=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
CONFIG_HYDRA=m
CONFIG_ZORRO8390=m
CONFIG_APNE=m
-CONFIG_APOLLO_ELPLUS=y
CONFIG_MAC8390=y
CONFIG_MAC89x0=m
CONFIG_MACSONIC=m
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_LOGO_MAC_CLUT224=y
-
-#
-# Sound
-#
CONFIG_SOUND=m
CONFIG_DMASOUND_ATARI=m
CONFIG_DMASOUND_PAULA=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set
# Character devices
#
CONFIG_ATARI_MFPSER=m
-CONFIG_ATARI_SCC=y
-CONFIG_ATARI_SCC_DMA=y
CONFIG_ATARI_MIDI=m
CONFIG_ATARI_DSP56K=m
CONFIG_AMIGA_BUILTIN_SERIAL=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
-# CONFIG_EXT4DEV_FS is not set
+CONFIG_EXT4DEV_FS=y
+# CONFIG_EXT4DEV_FS_XATTR is not set
CONFIG_JBD=y
+CONFIG_JBD2=y
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=y
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:08 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_PROC_HARDWARE=y
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
CONFIG_ISCSI_TCP=m
# CONFIG_SCSI_DEBUG is not set
CONFIG_MVME147_SCSI=y
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:09 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_PROC_HARDWARE=y
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
CONFIG_53C700_BE_BUS=y
# CONFIG_SCSI_DEBUG is not set
CONFIG_MVME16x_SCSI=y
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:10 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_GENERIC_ISA_DMA=y
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
#
# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
+CONFIG_IDE_ATAPI=y
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_BLK_DEV_PLATFORM is not set
CONFIG_BLK_DEV_Q40IDE=y
# CONFIG_BLK_DEV_IDEDMA is not set
-# CONFIG_BLK_DEV_HD_ONLY is not set
-# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
CONFIG_SOUND=m
CONFIG_DMASOUND_Q40=m
CONFIG_DMASOUND=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:11 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_PROC_HARDWARE=y
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
CONFIG_ISCSI_TCP=m
# CONFIG_SCSI_DEBUG is not set
CONFIG_SUN3_SCSI=y
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_B44 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
# Sonics Silicon Backplane
#
-CONFIG_SSB_POSSIBLE=y
-# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed May 28 22:47:35 2008
+# Linux kernel version: 2.6.27-rc6
+# Wed Sep 10 09:02:12 2008
#
CONFIG_M68K=y
CONFIG_MMU=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
# CONFIG_HAVE_OPROFILE is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_PROC_HARDWARE=y
CONFIG_ZONE_DMA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+# CONFIG_WIRELESS_EXT_SYSFS is not set
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=m
# CONFIG_MTD is not set
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
CONFIG_ISCSI_TCP=m
# CONFIG_SCSI_DEBUG is not set
CONFIG_SUN3X_ESP=y
+# CONFIG_SCSI_DH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
-CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-CONFIG_DM_MULTIPATH_EMC=m
-CONFIG_DM_MULTIPATH_RDAC=m
-CONFIG_DM_MULTIPATH_HP=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
CONFIG_MACVLAN=m
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
#
# Multimedia devices
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
+# CONFIG_OCFS2_FS_STATS is not set
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_DNOTIFY=y
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
CONFIG_HPFS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_SAMPLES is not set
#
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_GENERIC_FIND_NEXT_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
local_irq_enable();
}
-/*
- * There is a race when WAIT instruction executed with interrupt
- * enabled.
- * But it is implementation-dependent wheter the pipelie restarts when
- * a non-enabled interrupt is requested.
- */
-static void r4k_wait(void)
-{
- __asm__(" .set mips3 \n"
- " wait \n"
- " .set mips0 \n");
-}
+extern void r4k_wait(void);
/*
* This variant is preferable as it allows testing need_resched and going to
__setup("nowait", wait_disable);
-static inline void check_wait(void)
+void __init check_wait(void)
{
struct cpuinfo_mips *c = ¤t_cpu_data;
void __init check_bugs32(void)
{
- check_wait();
check_errata();
}
#include <asm/stackframe.h>
#include <asm/war.h>
#include <asm/page.h>
+#include <asm/thread_info.h>
#define PANIC_PIC(msg) \
.set push; \
__FINIT
+ .align 5 /* 32 byte rollback region */
+LEAF(r4k_wait)
+ .set push
+ .set noreorder
+ /* start of rollback region */
+ LONG_L t0, TI_FLAGS($28)
+ nop
+ andi t0, _TIF_NEED_RESCHED
+ bnez t0, 1f
+ nop
+ nop
+ nop
+ .set mips3
+ wait
+ /* end of rollback region (the region size must be power of two) */
+ .set pop
+1:
+ jr ra
+ END(r4k_wait)
+
+ .macro BUILD_ROLLBACK_PROLOGUE handler
+ FEXPORT(rollback_\handler)
+ .set push
+ .set noat
+ MFC0 k0, CP0_EPC
+ PTR_LA k1, r4k_wait
+ ori k0, 0x1f /* 32 byte rollback region */
+ xori k0, 0x1f
+ bne k0, k1, 9f
+ MTC0 k0, CP0_EPC
+9:
+ .set pop
+ .endm
+
.align 5
+BUILD_ROLLBACK_PROLOGUE handle_int
NESTED(handle_int, PT_SIZE, sp)
#ifdef CONFIG_TRACE_IRQFLAGS
/*
* This prototype is copied to ebase + n*IntCtl.VS and patched
* to invoke the handler
*/
+BUILD_ROLLBACK_PROLOGUE except_vec_vi
NESTED(except_vec_vi, 0, sp)
SAVE_SOME
SAVE_AT
clear_tsk_thread_flag(p, TIF_USEDFPU);
#ifdef CONFIG_MIPS_MT_FPAFF
+ clear_tsk_thread_flag(p, TIF_FPUBOUND);
+
/*
* FPU affinity support is cleaner if we track the
* user-visible CPU affinity from the very beginning.
#include <asm/types.h>
#include <asm/stacktrace.h>
+extern void check_wait(void);
+extern asmlinkage void r4k_wait(void);
+extern asmlinkage void rollback_handle_int(void);
extern asmlinkage void handle_int(void);
extern asmlinkage void handle_tlbm(void);
extern asmlinkage void handle_tlbl(void);
extern char except_vec_vi, except_vec_vi_lui;
extern char except_vec_vi_ori, except_vec_vi_end;
+ extern char rollback_except_vec_vi;
+ char *vec_start = (cpu_wait == r4k_wait) ?
+ &rollback_except_vec_vi : &except_vec_vi;
#ifdef CONFIG_MIPS_MT_SMTC
/*
* We need to provide the SMTC vectored interrupt handler
* Status.IM bit to be masked before going there.
*/
extern char except_vec_vi_mori;
- const int mori_offset = &except_vec_vi_mori - &except_vec_vi;
+ const int mori_offset = &except_vec_vi_mori - vec_start;
#endif /* CONFIG_MIPS_MT_SMTC */
- const int handler_len = &except_vec_vi_end - &except_vec_vi;
- const int lui_offset = &except_vec_vi_lui - &except_vec_vi;
- const int ori_offset = &except_vec_vi_ori - &except_vec_vi;
+ const int handler_len = &except_vec_vi_end - vec_start;
+ const int lui_offset = &except_vec_vi_lui - vec_start;
+ const int ori_offset = &except_vec_vi_ori - vec_start;
if (handler_len > VECTORSPACING) {
/*
panic("VECTORSPACING too small");
}
- memcpy(b, &except_vec_vi, handler_len);
+ memcpy(b, vec_start, handler_len);
#ifdef CONFIG_MIPS_MT_SMTC
BUG_ON(n > 7); /* Vector index %d exceeds SMTC maximum. */
extern char except_vec3_generic, except_vec3_r4000;
extern char except_vec4;
unsigned long i;
+ int rollback;
+
+ check_wait();
+ rollback = (cpu_wait == r4k_wait);
#if defined(CONFIG_KGDB)
if (kgdb_early_setup)
if (board_be_init)
board_be_init();
- set_except_vector(0, handle_int);
+ set_except_vector(0, rollback ? rollback_handle_int : handle_int);
set_except_vector(1, handle_tlbm);
set_except_vector(2, handle_tlbl);
set_except_vector(3, handle_tlbs);
SCHED_TEXT
LOCK_TEXT
KPROBES_TEXT
+ *(.text.*)
*(.fixup)
*(.gnu.warning)
} :text = 0
#ifdef USE_DOUBLE
#define LOAD ld
+#define LOAD32 lwu
#define ADD daddu
#define NBYTES 8
#else
#define LOAD lw
+#define LOAD32 lw
#define ADD addu
#define NBYTES 4
ADD sum, v1; \
.set pop
+#define ADDC32(sum,reg) \
+ .set push; \
+ .set noat; \
+ addu sum, reg; \
+ sltu v1, sum, reg; \
+ addu sum, v1; \
+ .set pop
+
#define CSUM_BIGCHUNK1(src, offset, sum, _t0, _t1, _t2, _t3) \
LOAD _t0, (offset + UNIT(0))(src); \
LOAD _t1, (offset + UNIT(1))(src); \
beqz t8, .Lqword_align
andi t8, src, 0x8
- lw t0, 0x00(src)
+ LOAD32 t0, 0x00(src)
LONG_SUBU a1, a1, 0x4
ADDC(sum, t0)
PTR_ADDU src, src, 0x4
LONG_SRL t8, t8, 0x2
.Lend_words:
- lw t0, (src)
+ LOAD32 t0, (src)
LONG_SUBU t8, t8, 0x1
ADDC(sum, t0)
.set reorder /* DADDI_WAR */
/* Still a full word to go */
ulw t1, (src)
PTR_ADDIU src, 4
+#ifdef USE_DOUBLE
+ dsll t1, t1, 32 /* clear lower 32bit */
+#endif
ADDC(sum, t1)
1: move t1, zero
1:
.set reorder
/* Add the passed partial csum. */
- ADDC(sum, a2)
+ ADDC32(sum, a2)
jr ra
.set noreorder
END(csum_partial)
.set pop
1:
.set reorder
- ADDC(sum, psum)
+ ADDC32(sum, psum)
jr ra
.set noreorder
cascade = irq_cascade + irq;
if (cascade->get_irq != NULL) {
unsigned int source_irq = irq;
+ int ret;
desc = irq_desc + source_irq;
if (desc->chip->mask_ack)
desc->chip->mask_ack(source_irq);
desc->chip->mask(source_irq);
desc->chip->ack(source_irq);
}
- irq = cascade->get_irq(irq);
- if (irq < 0)
+ ret = cascade->get_irq(irq);
+ irq = ret;
+ if (ret < 0)
atomic_inc(&irq_err_count);
else
irq_dispatch(irq);
* If we're in an interrupt or have no user
* context, we must not take the fault..
*/
- if (in_interrupt() || !mm)
+ if (in_atomic() || !mm)
goto no_context;
down_read(&mm->mmap_sem);
image-$(CONFIG_PPC_CHRP) += zImage.chrp
image-$(CONFIG_PPC_EFIKA) += zImage.chrp
image-$(CONFIG_PPC_PMAC) += zImage.pmac
-image-$(CONFIG_PPC_HOLLY) += zImage.holly
+image-$(CONFIG_PPC_HOLLY) += dtbImage.holly
image-$(CONFIG_PPC_PRPMC2800) += dtbImage.prpmc2800
image-$(CONFIG_PPC_ISERIES) += zImage.iseries
image-$(CONFIG_DEFAULT_UIMAGE) += uImage
cell-index = <0>;
reg = <0x0 0x80>;
interrupt-parent = <&mpic>;
- interrupts = <60 2>;
+ interrupts = <76 2>;
};
dma-channel@1 {
compatible = "fsl,mpc8610-dma-channel",
cell-index = <1>;
reg = <0x80 0x80>;
interrupt-parent = <&mpic>;
- interrupts = <61 2>;
+ interrupts = <77 2>;
};
dma-channel@2 {
compatible = "fsl,mpc8610-dma-channel",
cell-index = <2>;
reg = <0x100 0x80>;
interrupt-parent = <&mpic>;
- interrupts = <62 2>;
+ interrupts = <78 2>;
};
dma-channel@3 {
compatible = "fsl,mpc8610-dma-channel",
cell-index = <3>;
reg = <0x180 0x80>;
interrupt-parent = <&mpic>;
- interrupts = <63 2>;
+ interrupts = <79 2>;
};
};
/* Keep this the last entry. */
#define R_PPC64_NUM 107
+/* There's actually a third entry here, but it's unused */
+struct ppc64_opd_entry
+{
+ unsigned long funcaddr;
+ unsigned long r2;
+};
+
#ifdef __KERNEL__
#ifdef CONFIG_SPU_BASE
#define _ASM_POWERPC_SECTIONS_H
#ifdef __KERNEL__
+#include <linux/elf.h>
+#include <linux/uaccess.h>
#include <asm-generic/sections.h>
#ifdef __powerpc64__
}
#undef dereference_function_descriptor
-void *dereference_function_descriptor(void *);
+static inline void *dereference_function_descriptor(void *ptr)
+{
+ struct ppc64_opd_entry *desc = ptr;
+ void *p;
+
+ if (!probe_kernel_address(&desc->funcaddr, p))
+ ptr = p;
+ return ptr;
+}
#endif
#include <linux/err.h>
#include <linux/vmalloc.h>
#include <linux/bug.h>
-#include <linux/uaccess.h>
#include <asm/module.h>
-#include <asm/sections.h>
#include <asm/firmware.h>
#include <asm/code-patching.h>
#include <linux/sort.h>
#define DEBUGP(fmt , ...)
#endif
-/* There's actually a third entry here, but it's unused */
-struct ppc64_opd_entry
-{
- unsigned long funcaddr;
- unsigned long r2;
-};
-
/* Like PPC32, we need little trampolines to do > 24-bit jumps (into
the kernel itself). But on PPC64, these need to be used for every
jump, actually, to reset r2 (TOC+0x8000). */
return 0;
}
-
-void *dereference_function_descriptor(void *ptr)
-{
- struct ppc64_opd_entry *desc = ptr;
- void *p;
-
- if (!probe_kernel_address(&desc->funcaddr, p))
- ptr = p;
- return ptr;
-}
return of_bus_default_map(addr, range, na, ns, pna);
}
-static unsigned int of_bus_sbus_get_flags(const u32 *addr)
+static unsigned long of_bus_sbus_get_flags(const u32 *addr, unsigned long flags)
{
return IORESOURCE_MEM;
}
*/
[REGSET_GENERAL] = {
.core_note_type = NT_PRSTATUS,
- .n = 38 * sizeof(u32),
+ .n = 38,
.size = sizeof(u32), .align = sizeof(u32),
.get = genregs32_get, .set = genregs32_set
},
*/
[REGSET_FP] = {
.core_note_type = NT_PRFPREG,
- .n = 99 * sizeof(u32),
+ .n = 99,
.size = sizeof(u32), .align = sizeof(u32),
.get = fpregs32_get, .set = fpregs32_set
},
#include <linux/module.h>
#include <linux/sched.h>
+#include <linux/linkage.h>
#include <linux/ptrace.h>
#include <linux/errno.h>
#include <linux/kernel_stat.h>
: "g1", "g2");
}
-void init_irqwork_curcpu(void)
+void notrace init_irqwork_curcpu(void)
{
int cpu = hard_smp_processor_id();
}
}
-void __cpuinit sun4v_register_mondo_queues(int this_cpu)
+void __cpuinit notrace sun4v_register_mondo_queues(int this_cpu)
{
struct trap_per_cpu *tb = &trap_block[this_cpu];
static int of_bus_pci_match(struct device_node *np)
{
- if (!strcmp(np->type, "pci") || !strcmp(np->type, "pciex")) {
+ if (!strcmp(np->name, "pci")) {
const char *model = of_get_property(np, "model", NULL);
if (model && !strcmp(model, "SUNW,simba"))
/* Treat PCI busses lacking ranges property just like
* simba.
*/
- if (!strcmp(np->type, "pci") || !strcmp(np->type, "pciex")) {
+ if (!strcmp(np->name, "pci")) {
if (!of_find_property(np, "ranges", NULL))
return 1;
}
* it lacks a ranges property, and this will include
* cases like Simba.
*/
- if (!strcmp(pp->type, "pci") || !strcmp(pp->type, "pciex"))
+ if (!strcmp(pp->name, "pci"))
return 0;
return 1;
break;
}
} else {
- if (!strcmp(pp->type, "pci") ||
- !strcmp(pp->type, "pciex")) {
+ if (!strcmp(pp->name, "pci")) {
unsigned int this_orig_irq = irq;
irq = pci_irq_swizzle(dp, pp, irq);
dev->current_state = 4; /* unknown power state */
dev->error_state = pci_channel_io_normal;
- if (!strcmp(type, "pci") || !strcmp(type, "pciex")) {
+ if (!strcmp(node->name, "pci")) {
/* a PCI-PCI bridge */
dev->hdr_type = PCI_HEADER_TYPE_BRIDGE;
dev->rom_base_reg = PCI_ROM_ADDRESS1;
{
unsigned long csr_reg, csr, csr_error_bits;
irqreturn_t ret = IRQ_NONE;
- u16 stat;
+ u16 stat, *addr;
if (is_pbm_a) {
csr_reg = pbm->controller_regs + PSYCHO_PCIA_CTRL;
printk("%s: PCI SERR signal asserted.\n", pbm->name);
ret = IRQ_HANDLED;
}
- pci_read_config_word(pbm->pci_bus->self, PCI_STATUS, &stat);
+ addr = psycho_pci_config_mkaddr(pbm, pbm->pci_first_busno,
+ 0, PCI_STATUS);
+ pci_config_read16(addr, &stat);
if (stat & (PCI_STATUS_PARITY |
PCI_STATUS_SIG_TARGET_ABORT |
PCI_STATUS_REC_TARGET_ABORT |
PCI_STATUS_SIG_SYSTEM_ERROR)) {
printk("%s: PCI bus error, PCI_STATUS[%04x]\n",
pbm->name, stat);
- pci_write_config_word(pbm->pci_bus->self, PCI_STATUS, 0xffff);
+ pci_config_write16(addr, 0xffff);
ret = IRQ_HANDLED;
}
return ret;
* the second will just error out since we do not pass in
* IRQF_SHARED.
*/
- err = request_irq(op->irqs[1], psycho_ue_intr, 0,
+ err = request_irq(op->irqs[1], psycho_ue_intr, IRQF_SHARED,
"PSYCHO_UE", pbm);
- err = request_irq(op->irqs[2], psycho_ce_intr, 0,
+ err = request_irq(op->irqs[2], psycho_ce_intr, IRQF_SHARED,
"PSYCHO_CE", pbm);
/* This one, however, ought not to fail. We can just warn
* about it since the system can still operate properly even
* if this fails.
*/
- err = request_irq(op->irqs[0], psycho_pcierr_intr, 0,
+ err = request_irq(op->irqs[0], psycho_pcierr_intr, IRQF_SHARED,
"PSYCHO_PCIERR", pbm);
if (err)
printk(KERN_WARNING "%s: Could not register PCIERR, "
return PSYCHO_IMAP_B_SLOT0 + (slot * 8);
}
-#define PSYCHO_IMAP_SCSI 0x1000UL
-#define PSYCHO_IMAP_ETH 0x1008UL
-#define PSYCHO_IMAP_BPP 0x1010UL
-#define PSYCHO_IMAP_AU_REC 0x1018UL
-#define PSYCHO_IMAP_AU_PLAY 0x1020UL
-#define PSYCHO_IMAP_PFAIL 0x1028UL
-#define PSYCHO_IMAP_KMS 0x1030UL
-#define PSYCHO_IMAP_FLPY 0x1038UL
-#define PSYCHO_IMAP_SHW 0x1040UL
-#define PSYCHO_IMAP_KBD 0x1048UL
-#define PSYCHO_IMAP_MS 0x1050UL
-#define PSYCHO_IMAP_SER 0x1058UL
-#define PSYCHO_IMAP_TIM0 0x1060UL
-#define PSYCHO_IMAP_TIM1 0x1068UL
-#define PSYCHO_IMAP_UE 0x1070UL
-#define PSYCHO_IMAP_CE 0x1078UL
-#define PSYCHO_IMAP_A_ERR 0x1080UL
-#define PSYCHO_IMAP_B_ERR 0x1088UL
-#define PSYCHO_IMAP_PMGMT 0x1090UL
-#define PSYCHO_IMAP_GFX 0x1098UL
-#define PSYCHO_IMAP_EUPA 0x10a0UL
-
-static unsigned long __psycho_onboard_imap_off[] = {
-/*0x20*/ PSYCHO_IMAP_SCSI,
-/*0x21*/ PSYCHO_IMAP_ETH,
-/*0x22*/ PSYCHO_IMAP_BPP,
-/*0x23*/ PSYCHO_IMAP_AU_REC,
-/*0x24*/ PSYCHO_IMAP_AU_PLAY,
-/*0x25*/ PSYCHO_IMAP_PFAIL,
-/*0x26*/ PSYCHO_IMAP_KMS,
-/*0x27*/ PSYCHO_IMAP_FLPY,
-/*0x28*/ PSYCHO_IMAP_SHW,
-/*0x29*/ PSYCHO_IMAP_KBD,
-/*0x2a*/ PSYCHO_IMAP_MS,
-/*0x2b*/ PSYCHO_IMAP_SER,
-/*0x2c*/ PSYCHO_IMAP_TIM0,
-/*0x2d*/ PSYCHO_IMAP_TIM1,
-/*0x2e*/ PSYCHO_IMAP_UE,
-/*0x2f*/ PSYCHO_IMAP_CE,
-/*0x30*/ PSYCHO_IMAP_A_ERR,
-/*0x31*/ PSYCHO_IMAP_B_ERR,
-/*0x32*/ PSYCHO_IMAP_PMGMT,
-/*0x33*/ PSYCHO_IMAP_GFX,
-/*0x34*/ PSYCHO_IMAP_EUPA,
-};
+#define PSYCHO_OBIO_IMAP_BASE 0x1000UL
+
#define PSYCHO_ONBOARD_IRQ_BASE 0x20
-#define PSYCHO_ONBOARD_IRQ_LAST 0x34
#define psycho_onboard_imap_offset(__ino) \
- __psycho_onboard_imap_off[(__ino) - PSYCHO_ONBOARD_IRQ_BASE]
+ (PSYCHO_OBIO_IMAP_BASE + (((__ino) & 0x1f) << 3))
#define PSYCHO_ICLR_A_SLOT0 0x1400UL
#define PSYCHO_ICLR_SCSI 0x1800UL
imap_off = psycho_pcislot_imap_offset(ino);
} else {
/* Onboard device */
- if (ino > PSYCHO_ONBOARD_IRQ_LAST) {
- prom_printf("psycho_irq_build: Wacky INO [%x]\n", ino);
- prom_halt();
- }
imap_off = psycho_onboard_imap_offset(ino);
}
#define SABRE_IMAP_A_SLOT0 0x0c00UL
#define SABRE_IMAP_B_SLOT0 0x0c20UL
-#define SABRE_IMAP_SCSI 0x1000UL
-#define SABRE_IMAP_ETH 0x1008UL
-#define SABRE_IMAP_BPP 0x1010UL
-#define SABRE_IMAP_AU_REC 0x1018UL
-#define SABRE_IMAP_AU_PLAY 0x1020UL
-#define SABRE_IMAP_PFAIL 0x1028UL
-#define SABRE_IMAP_KMS 0x1030UL
-#define SABRE_IMAP_FLPY 0x1038UL
-#define SABRE_IMAP_SHW 0x1040UL
-#define SABRE_IMAP_KBD 0x1048UL
-#define SABRE_IMAP_MS 0x1050UL
-#define SABRE_IMAP_SER 0x1058UL
-#define SABRE_IMAP_UE 0x1070UL
-#define SABRE_IMAP_CE 0x1078UL
-#define SABRE_IMAP_PCIERR 0x1080UL
-#define SABRE_IMAP_GFX 0x1098UL
-#define SABRE_IMAP_EUPA 0x10a0UL
#define SABRE_ICLR_A_SLOT0 0x1400UL
#define SABRE_ICLR_B_SLOT0 0x1480UL
#define SABRE_ICLR_SCSI 0x1800UL
return SABRE_IMAP_B_SLOT0 + (slot * 8);
}
-static unsigned long __sabre_onboard_imap_off[] = {
-/*0x20*/ SABRE_IMAP_SCSI,
-/*0x21*/ SABRE_IMAP_ETH,
-/*0x22*/ SABRE_IMAP_BPP,
-/*0x23*/ SABRE_IMAP_AU_REC,
-/*0x24*/ SABRE_IMAP_AU_PLAY,
-/*0x25*/ SABRE_IMAP_PFAIL,
-/*0x26*/ SABRE_IMAP_KMS,
-/*0x27*/ SABRE_IMAP_FLPY,
-/*0x28*/ SABRE_IMAP_SHW,
-/*0x29*/ SABRE_IMAP_KBD,
-/*0x2a*/ SABRE_IMAP_MS,
-/*0x2b*/ SABRE_IMAP_SER,
-/*0x2c*/ 0 /* reserved */,
-/*0x2d*/ 0 /* reserved */,
-/*0x2e*/ SABRE_IMAP_UE,
-/*0x2f*/ SABRE_IMAP_CE,
-/*0x30*/ SABRE_IMAP_PCIERR,
-/*0x31*/ 0 /* reserved */,
-/*0x32*/ 0 /* reserved */,
-/*0x33*/ SABRE_IMAP_GFX,
-/*0x34*/ SABRE_IMAP_EUPA,
-};
-#define SABRE_ONBOARD_IRQ_BASE 0x20
-#define SABRE_ONBOARD_IRQ_LAST 0x30
+#define SABRE_OBIO_IMAP_BASE 0x1000UL
+#define SABRE_ONBOARD_IRQ_BASE 0x20
#define sabre_onboard_imap_offset(__ino) \
- __sabre_onboard_imap_off[(__ino) - SABRE_ONBOARD_IRQ_BASE]
+ (SABRE_OBIO_IMAP_BASE + (((__ino) & 0x1f) << 3))
#define sabre_iclr_offset(ino) \
((ino & 0x20) ? (SABRE_ICLR_SCSI + (((ino) & 0x1f) << 3)) : \
imap_off = sabre_pcislot_imap_offset(ino);
} else {
/* onboard device */
- if (ino > SABRE_ONBOARD_IRQ_LAST) {
- prom_printf("sabre_irq_build: Wacky INO [%x]\n", ino);
- prom_halt();
- }
imap_off = sabre_onboard_imap_offset(ino);
}
*/
[REGSET_GENERAL] = {
.core_note_type = NT_PRSTATUS,
- .n = 36 * sizeof(u64),
+ .n = 36,
.size = sizeof(u64), .align = sizeof(u64),
.get = genregs64_get, .set = genregs64_set
},
*/
[REGSET_FP] = {
.core_note_type = NT_PRFPREG,
- .n = 35 * sizeof(u64),
+ .n = 35,
.size = sizeof(u64), .align = sizeof(u64),
.get = fpregs64_get, .set = fpregs64_set
},
*/
[REGSET_GENERAL] = {
.core_note_type = NT_PRSTATUS,
- .n = 38 * sizeof(u32),
+ .n = 38,
.size = sizeof(u32), .align = sizeof(u32),
.get = genregs32_get, .set = genregs32_set
},
*/
[REGSET_FP] = {
.core_note_type = NT_PRFPREG,
- .n = 99 * sizeof(u32),
+ .n = 99,
.size = sizeof(u32), .align = sizeof(u32),
.get = fpregs32_get, .set = fpregs32_set
},
#include <linux/module.h>
#include <linux/sched.h>
+#include <linux/linkage.h>
#include <linux/kernel.h>
#include <linux/signal.h>
#include <linux/smp.h>
/* This can get invoked before sched_init() so play it super safe
* and use hard_smp_processor_id().
*/
-void init_cur_cpu_trap(struct thread_info *t)
+void notrace init_cur_cpu_trap(struct thread_info *t)
{
int cpu = hard_smp_processor_id();
struct trap_per_cpu *p = &trap_block[cpu];
u64 *spte;
int young = 0;
+ /* always return old for EPT */
+ if (!shadow_accessed_mask)
+ return 0;
+
spte = rmap_next(kvm, rmapp, NULL);
while (spte) {
int _young;
module_param(npt, int, S_IRUGO);
static void kvm_reput_irq(struct vcpu_svm *svm);
+static void svm_flush_tlb(struct kvm_vcpu *vcpu);
static inline struct vcpu_svm *to_svm(struct kvm_vcpu *vcpu)
{
static void svm_set_cr4(struct kvm_vcpu *vcpu, unsigned long cr4)
{
unsigned long host_cr4_mce = read_cr4() & X86_CR4_MCE;
+ unsigned long old_cr4 = to_svm(vcpu)->vmcb->save.cr4;
+
+ if (npt_enabled && ((old_cr4 ^ cr4) & X86_CR4_PGE))
+ force_new_asid(vcpu);
vcpu->arch.cr4 = cr4;
if (!npt_enabled)
KVMTRACE_3D(TDP_FAULT, &svm->vcpu, error_code,
(u32)fault_address, (u32)(fault_address >> 32),
handler);
+ /*
+ * FIXME: Tis shouldn't be necessary here, but there is a flush
+ * missing in the MMU code. Until we find this bug, flush the
+ * complete TLB here on an NPF
+ */
+ if (npt_enabled)
+ svm_flush_tlb(&svm->vcpu);
if (event_injection)
kvm_mmu_unprotect_page_virt(&svm->vcpu, fault_address);
kvm_mmu_set_base_ptes(VMX_EPT_READABLE_MASK |
VMX_EPT_WRITABLE_MASK |
VMX_EPT_DEFAULT_MT << VMX_EPT_MT_EPTE_SHIFT);
- kvm_mmu_set_mask_ptes(0ull, VMX_EPT_FAKE_ACCESSED_MASK,
- VMX_EPT_FAKE_DIRTY_MASK, 0ull,
+ kvm_mmu_set_mask_ptes(0ull, 0ull, 0ull, 0ull,
VMX_EPT_EXECUTABLE_MASK);
kvm_enable_tdp();
} else
#define VMX_EPT_READABLE_MASK 0x1ull
#define VMX_EPT_WRITABLE_MASK 0x2ull
#define VMX_EPT_EXECUTABLE_MASK 0x4ull
-#define VMX_EPT_FAKE_ACCESSED_MASK (1ull << 62)
-#define VMX_EPT_FAKE_DIRTY_MASK (1ull << 63)
#define VMX_EPT_IDENTITY_PAGETABLE_ADDR 0xfffbc000ul
}
EXPORT_SYMBOL(blk_verify_command);
+#if 0
/* and now, the sysfs stuff */
static ssize_t rcf_cmds_show(struct blk_cmd_filter *filter, char *page,
int rw)
kobject_put(disk->holder_dir->parent);
}
EXPORT_SYMBOL(blk_unregister_filter);
+#endif
* off.
*/
if (pdev->vendor == PCI_VENDOR_ID_INTEL && pdev->device == 0x2652) {
- int rc = piix_disable_ahci(pdev);
+ rc = piix_disable_ahci(pdev);
if (rc)
return rc;
}
PORT_SCR = 0x20,
/* HOST_CTL bits */
+ HCTL_LEDEN = (1 << 3), /* enable LED operation */
HCTL_IRQOFF = (1 << 8), /* global IRQ off */
HCTL_FTHD0 = (1 << 10), /* fifo threshold 0 */
HCTL_FTHD1 = (1 << 11), /* fifo threshold 1*/
void __iomem *port_base = inic_port_base(ap);
/* fire up the ADMA engine */
- writew(HCTL_FTHD0, port_base + HOST_CTL);
+ writew(HCTL_FTHD0 | HCTL_LEDEN, port_base + HOST_CTL);
writew(IDMA_CTL_GO, port_base + PORT_IDMA_CTL);
writeb(0, port_base + PORT_CPB_PTQFIFO);
/* Number of monotonicity checks to perform during initialization */
#define ACPI_PM_MONOTONICITY_CHECKS 10
+/* Number of reads we try to get two different values */
+#define ACPI_PM_READ_CHECKS 10000
static int __init init_acpi_pm_clocksource(void)
{
cycle_t value1, value2;
- unsigned int i, j, good = 0;
+ unsigned int i, j = 0;
if (!pmtmr_ioport)
return -ENODEV;
/* "verify" this timing source: */
for (j = 0; j < ACPI_PM_MONOTONICITY_CHECKS; j++) {
+ udelay(100 * j);
value1 = clocksource_acpi_pm.read();
- for (i = 0; i < 10000; i++) {
+ for (i = 0; i < ACPI_PM_READ_CHECKS; i++) {
value2 = clocksource_acpi_pm.read();
if (value2 == value1)
continue;
if (value2 > value1)
- good++;
break;
if ((value2 < value1) && ((value2) < 0xFFF))
- good++;
break;
printk(KERN_INFO "PM-Timer had inconsistent results:"
" 0x%#llx, 0x%#llx - aborting.\n",
value1, value2);
return -EINVAL;
}
- udelay(300 * i);
- }
-
- if (good != ACPI_PM_MONOTONICITY_CHECKS) {
- printk(KERN_INFO "PM-Timer failed consistency check "
- " (0x%#llx) - aborting.\n", value1);
- return -ENODEV;
+ if (i == ACPI_PM_READ_CHECKS) {
+ printk(KERN_INFO "PM-Timer failed consistency check "
+ " (0x%#llx) - aborting.\n", value1);
+ return -ENODEV;
+ }
}
if (verify_pmtmr_rate() != 0)
edesc->desc.hdr = ctx->desc_hdr_template | DESC_HDR_MODE0_ENCRYPT;
memcpy(req->giv, ctx->iv, crypto_aead_ivsize(authenc));
+ /* avoid consecutive packets going out with same IV */
+ *(__be64 *)req->giv ^= cpu_to_be64(req->seq);
return ipsec_esp(edesc, areq, req->giv, req->seq,
ipsec_esp_encrypt_done);
priv->ofdev = ofdev;
+ INIT_LIST_HEAD(&priv->alg_list);
+
tasklet_init(&priv->done_task, talitos_done, (unsigned long)dev);
tasklet_init(&priv->error_task, talitos_error, (unsigned long)dev);
}
/* register crypto algorithms the device supports */
- INIT_LIST_HEAD(&priv->alg_list);
-
for (i = 0; i < ARRAY_SIZE(driver_algs); i++) {
if (hw_supports(dev, driver_algs[i].desc_hdr_template)) {
struct talitos_crypto_alg *t_alg;
return i2c_smbus_write_byte_data(client, reg, value);
}
-struct ad7414_data *ad7414_update_device(struct device *dev)
+static struct ad7414_data *ad7414_update_device(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct ad7414_data *data = i2c_get_clientdata(client);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("System voltages control via Attansic ATXP1");
-MODULE_VERSION("0.6.2");
+MODULE_VERSION("0.6.3");
MODULE_AUTHOR("Sebastian Witt <se.witt@gmx.net>");
#define ATXP1_VID 0x00
if (!((i2c_smbus_read_byte_data(new_client, 0x3e) == 0) &&
(i2c_smbus_read_byte_data(new_client, 0x3f) == 0) &&
(i2c_smbus_read_byte_data(new_client, 0xfe) == 0) &&
- (i2c_smbus_read_byte_data(new_client, 0xff) == 0) )) {
+ (i2c_smbus_read_byte_data(new_client, 0xff) == 0)))
+ return -ENODEV;
- /* No vendor ID, now checking if registers 0x10,0x11 (non-existent)
- * showing the same as register 0x00 */
- temp = i2c_smbus_read_byte_data(new_client, 0x00);
+ /* No vendor ID, now checking if registers 0x10,0x11 (non-existent)
+ * showing the same as register 0x00 */
+ temp = i2c_smbus_read_byte_data(new_client, 0x00);
- if (!((i2c_smbus_read_byte_data(new_client, 0x10) == temp) &&
- (i2c_smbus_read_byte_data(new_client, 0x11) == temp) ))
- return -ENODEV;
- }
+ if (!((i2c_smbus_read_byte_data(new_client, 0x10) == temp) &&
+ (i2c_smbus_read_byte_data(new_client, 0x11) == temp)))
+ return -ENODEV;
/* Get VRM */
temp = vid_which_vrm();
static inline int has_16bit_fans(const struct it87_data *data)
{
/* IT8705F Datasheet 0.4.1, 3h == Version G.
- IT8712F Datasheet 0.9.1, section 8.3.5 indicates 7h == Version I.
+ IT8712F Datasheet 0.9.1, section 8.3.5 indicates 8h == Version J.
These are the first revisions with 16bit tachometer support. */
return (data->type == it87 && data->revision >= 0x03)
- || (data->type == it8712 && data->revision >= 0x07)
+ || (data->type == it8712 && data->revision >= 0x08)
|| data->type == it8716
|| data->type == it8718;
}
ide_proc_unregister_driver(drive, info->driver);
- blk_unregister_filter(info->disk);
del_gendisk(info->disk);
ide_cd_put(info);
g->fops = &idecd_ops;
g->flags |= GENHD_FL_REMOVABLE;
add_disk(g);
- blk_register_filter(g);
return 0;
out_free_cd:
return 0;
}
+static struct hpt_info *hpt3xx_get_info(struct device *dev)
+{
+ struct ide_host *host = dev_get_drvdata(dev);
+ struct hpt_info *info = (struct hpt_info *)host->host_priv;
+
+ return dev == host->dev[1] ? info + 1 : info;
+}
+
/*
* The Marvell bridge chips used on the HighPoint SATA cards do not seem
* to support the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes...
static u8 hpt3xx_udma_filter(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct ide_host *host = pci_get_drvdata(dev);
- struct hpt_info *info = host->host_priv + (hwif->dev == host->dev[1]);
+ struct hpt_info *info = hpt3xx_get_info(hwif->dev);
u8 mask = hwif->ultra_mask;
switch (info->chip_type) {
static u8 hpt3xx_mdma_filter(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct ide_host *host = pci_get_drvdata(dev);
- struct hpt_info *info = host->host_priv + (hwif->dev == host->dev[1]);
+ struct hpt_info *info = hpt3xx_get_info(hwif->dev);
switch (info->chip_type) {
case HPT372 :
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct ide_host *host = pci_get_drvdata(dev);
- struct hpt_info *info = host->host_priv + (hwif->dev == host->dev[1]);
+ struct hpt_info *info = hpt3xx_get_info(hwif->dev);
struct hpt_timings *t = info->timings;
u8 itr_addr = 0x40 + (drive->dn * 4);
u32 old_itr = 0;
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct ide_host *host = pci_get_drvdata(dev);
- struct hpt_info *info = host->host_priv + (hwif->dev == host->dev[1]);
+ struct hpt_info *info = hpt3xx_get_info(hwif->dev);
if (drive->quirk_list) {
if (info->chip_type >= HPT370) {
static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev)
{
unsigned long io_base = pci_resource_start(dev, 4);
- struct ide_host *host = pci_get_drvdata(dev);
- struct hpt_info *info = host->host_priv + (&dev->dev == host->dev[1]);
+ struct hpt_info *info = hpt3xx_get_info(&dev->dev);
const char *name = DRV_NAME;
u8 pci_clk, dpll_clk = 0; /* PCI and DPLL clock in MHz */
u8 chip_type;
static u8 hpt3xx_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct ide_host *host = pci_get_drvdata(dev);
- struct hpt_info *info = host->host_priv + (hwif->dev == host->dev[1]);
+ struct hpt_info *info = hpt3xx_get_info(hwif->dev);
u8 chip_type = info->chip_type;
u8 scr1 = 0, ata66 = hwif->channel ? 0x01 : 0x02;
static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct ide_host *host = pci_get_drvdata(dev);
- struct hpt_info *info = host->host_priv + (hwif->dev == host->dev[1]);
+ struct hpt_info *info = hpt3xx_get_info(hwif->dev);
int serialize = HPT_SERIALIZE_IO;
u8 chip_type = info->chip_type;
u8 new_mcr, old_mcr = 0;
static void set_fmr_seg(struct mlx4_wqe_fmr_seg *fseg, struct ib_send_wr *wr)
{
struct mlx4_ib_fast_reg_page_list *mfrpl = to_mfrpl(wr->wr.fast_reg.page_list);
+ int i;
+
+ for (i = 0; i < wr->wr.fast_reg.page_list_len; ++i)
+ wr->wr.fast_reg.page_list->page_list[i] =
+ cpu_to_be64(wr->wr.fast_reg.page_list->page_list[i] |
+ MLX4_MTT_FLAG_PRESENT);
fseg->flags = convert_access(wr->wr.fast_reg.access_flags);
fseg->mem_key = cpu_to_be32(wr->wr.fast_reg.rkey);
return ret;
cleanup_retrans_entry(cm_node);
cm_node->state = NES_CM_STATE_CLOSED;
- ret = send_fin(cm_node, NULL);
-
- if (cm_node->accept_pend) {
- BUG_ON(!cm_node->listener);
- atomic_dec(&cm_node->listener->pend_accepts_cnt);
- BUG_ON(atomic_read(&cm_node->listener->pend_accepts_cnt) < 0);
- }
ret = send_reset(cm_node, NULL);
return ret;
atomic_inc(&cm_disconnects);
cm_event.event = IW_CM_EVENT_DISCONNECT;
if (last_ae == NES_AEQE_AEID_LLP_CONNECTION_RESET) {
+ issued_disconnect_reset = 1;
cm_event.status = IW_CM_EVENT_STATUS_RESET;
nes_debug(NES_DBG_CM, "Generating a CM "
"Disconnect Event (status reset) for "
nes_debug(NES_DBG_CM, "Call close API\n");
g_cm_core->api->close(g_cm_core, nesqp->cm_node);
- nesqp->cm_node = NULL;
}
return ret;
cm_node->apbvt_set = 1;
nesqp->cm_node = cm_node;
cm_node->nesqp = nesqp;
+ nes_add_ref(&nesqp->ibqp);
return 0;
}
if (ret)
printk(KERN_ERR "%s[%u] OFA CM event_handler returned, "
"ret=%d\n", __func__, __LINE__, ret);
- nes_rem_ref(&nesqp->ibqp);
cm_id->rem_ref(cm_id);
rem_ref_cm_node(event->cm_node->cm_core, event->cm_node);
struct delayed_work pkey_poll_task;
struct delayed_work mcast_task;
+ struct work_struct carrier_on_task;
struct work_struct flush_light;
struct work_struct flush_normal;
struct work_struct flush_heavy;
void ipoib_dev_cleanup(struct net_device *dev);
void ipoib_mcast_join_task(struct work_struct *work);
+void ipoib_mcast_carrier_on_task(struct work_struct *work);
void ipoib_mcast_send(struct net_device *dev, void *mgid, struct sk_buff *skb);
void ipoib_mcast_restart_task(struct work_struct *work);
INIT_DELAYED_WORK(&priv->pkey_poll_task, ipoib_pkey_poll);
INIT_DELAYED_WORK(&priv->mcast_task, ipoib_mcast_join_task);
+ INIT_WORK(&priv->carrier_on_task, ipoib_mcast_carrier_on_task);
INIT_WORK(&priv->flush_light, ipoib_ib_dev_flush_light);
INIT_WORK(&priv->flush_normal, ipoib_ib_dev_flush_normal);
INIT_WORK(&priv->flush_heavy, ipoib_ib_dev_flush_heavy);
return ret;
}
+void ipoib_mcast_carrier_on_task(struct work_struct *work)
+{
+ struct ipoib_dev_priv *priv = container_of(work, struct ipoib_dev_priv,
+ carrier_on_task);
+
+ /*
+ * Take rtnl_lock to avoid racing with ipoib_stop() and
+ * turning the carrier back on while a device is being
+ * removed.
+ */
+ rtnl_lock();
+ netif_carrier_on(priv->dev);
+ rtnl_unlock();
+}
+
static int ipoib_mcast_join_complete(int status,
struct ib_sa_multicast *multicast)
{
&priv->mcast_task, 0);
mutex_unlock(&mcast_mutex);
- if (mcast == priv->broadcast) {
- /*
- * Take RTNL lock here to avoid racing with
- * ipoib_stop() and turning the carrier back
- * on while a device is being removed.
- */
- rtnl_lock();
- netif_carrier_on(dev);
- rtnl_unlock();
- }
+ /*
+ * Defer carrier on work to ipoib_workqueue to avoid a
+ * deadlock on rtnl_lock here.
+ */
+ if (mcast == priv->broadcast)
+ queue_work(ipoib_workqueue, &priv->carrier_on_task);
return 0;
}
#define BCM5974_WELLSPRING_MODE_REQUEST_VALUE 0x300
#define BCM5974_WELLSPRING_MODE_REQUEST_INDEX 0
#define BCM5974_WELLSPRING_MODE_VENDOR_VALUE 0x01
+#define BCM5974_WELLSPRING_MODE_NORMAL_VALUE 0x08
-static int bcm5974_wellspring_mode(struct bcm5974 *dev)
+static int bcm5974_wellspring_mode(struct bcm5974 *dev, bool on)
{
char *data = kmalloc(8, GFP_KERNEL);
int retval = 0, size;
}
/* apply the mode switch */
- data[0] = BCM5974_WELLSPRING_MODE_VENDOR_VALUE;
+ data[0] = on ?
+ BCM5974_WELLSPRING_MODE_VENDOR_VALUE :
+ BCM5974_WELLSPRING_MODE_NORMAL_VALUE;
/* write configuration */
size = usb_control_msg(dev->udev, usb_sndctrlpipe(dev->udev, 0),
goto out;
}
- dprintk(2, "bcm5974: switched to wellspring mode.\n");
+ dprintk(2, "bcm5974: switched to %s mode.\n",
+ on ? "wellspring" : "normal");
out:
kfree(data);
*/
static int bcm5974_start_traffic(struct bcm5974 *dev)
{
- if (bcm5974_wellspring_mode(dev)) {
+ if (bcm5974_wellspring_mode(dev, true)) {
dprintk(1, "bcm5974: mode switch failed\n");
goto error;
}
{
usb_kill_urb(dev->tp_urb);
usb_kill_urb(dev->bt_urb);
+ bcm5974_wellspring_mode(dev, false);
}
/*
input_dev->id.bustype = BUS_HOST;
input_dev->dev.parent = &pdev->dev;
- input_dev->evbit[0] = BIT(EV_KEY) | BIT(EV_ABS);
- input_dev->keybit[LONG(BTN_TOUCH)] = BIT(BTN_TOUCH);
+ input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
+ input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
input_set_abs_params(input_dev, ABS_X, 270, 3900, 0, 0);
input_set_abs_params(input_dev, ABS_Y, 180, 3700, 0, 0);
* time 'round when curr_resync == 2
*/
continue;
- prepare_to_wait(&resync_wait, &wq, TASK_UNINTERRUPTIBLE);
+ /* We need to wait 'interruptible' so as not to
+ * contribute to the load average, and not to
+ * be caught by 'softlockup'
+ */
+ prepare_to_wait(&resync_wait, &wq, TASK_INTERRUPTIBLE);
if (!kthread_should_stop() &&
mddev2->curr_resync >= mddev->curr_resync) {
printk(KERN_INFO "md: delaying %s of %s"
" share one or more physical units)\n",
desc, mdname(mddev), mdname(mddev2));
mddev_put(mddev2);
+ if (signal_pending(current))
+ flush_signals(current);
schedule();
finish_wait(&resync_wait, &wq);
goto try_again;
config VIDEO_SH_MOBILE_CEU
tristate "SuperH Mobile CEU Interface driver"
- depends on VIDEO_DEV
+ depends on VIDEO_DEV && HAS_DMA
select SOC_CAMERA
select VIDEOBUF_DMA_CONTIG
---help---
}
static struct class memstick_host_class = {
- .name = "memstick_host",
+ .name = "memstick_host",
.dev_release = memstick_free
};
* @sg - TPC argument
*/
void memstick_init_req_sg(struct memstick_request *mrq, unsigned char tpc,
- struct scatterlist *sg)
+ const struct scatterlist *sg)
{
mrq->tpc = tpc;
if (tpc & 8)
* user supplied buffer.
*/
void memstick_init_req(struct memstick_request *mrq, unsigned char tpc,
- void *buf, size_t length)
+ const void *buf, size_t length)
{
mrq->tpc = tpc;
if (tpc & 8)
if (!host->card) {
if (memstick_power_on(host))
goto out_power_off;
- } else
+ } else if (host->card->stop)
host->card->stop(host->card);
card = memstick_alloc_card(host);
|| !(host->card->check(host->card))) {
device_unregister(&host->card->dev);
host->card = NULL;
- } else
+ } else if (host->card->start)
host->card->start(host->card);
}
#define MSPRO_BLOCK_SIGNATURE 0xa5c3
#define MSPRO_BLOCK_MAX_ATTRIBUTES 41
+#define MSPRO_BLOCK_PART_SHIFT 3
+
enum {
MSPRO_BLOCK_ID_SYSINFO = 0x10,
MSPRO_BLOCK_ID_MODELNAME = 0x15,
static int mspro_block_disk_release(struct gendisk *disk)
{
struct mspro_block_data *msb = disk->private_data;
- int disk_id = disk->first_minor >> MEMSTICK_PART_SHIFT;
+ int disk_id = disk->first_minor >> MSPRO_BLOCK_PART_SHIFT;
mutex_lock(&mspro_block_disk_lock);
struct mspro_block_data *msb = memstick_get_drvdata(card);
int rc = 0;
+try_again:
if (msb->caps & MEMSTICK_CAP_PAR4)
rc = mspro_block_set_interface(card, MEMSTICK_SYS_PAR4);
else
rc = memstick_set_rw_addr(card);
if (!rc)
rc = mspro_block_set_interface(card, msb->system);
+
+ if (!rc) {
+ msleep(150);
+ rc = mspro_block_wait_for_ced(card);
+ if (rc)
+ return rc;
+
+ if (msb->caps & MEMSTICK_CAP_PAR8) {
+ msb->caps &= ~MEMSTICK_CAP_PAR8;
+ goto try_again;
+ }
+ }
}
return rc;
}
return -EIO;
msb->caps = host->caps;
- rc = mspro_block_switch_interface(card);
+
+ msleep(150);
+ rc = mspro_block_wait_for_ced(card);
if (rc)
return rc;
- msleep(200);
- rc = mspro_block_wait_for_ced(card);
+ rc = mspro_block_switch_interface(card);
if (rc)
return rc;
+
dev_dbg(&card->dev, "card activated\n");
if (msb->system != MEMSTICK_SYS_SERIAL)
msb->caps |= MEMSTICK_CAP_AUTO_GET_INT;
if (rc)
return rc;
- if ((disk_id << MEMSTICK_PART_SHIFT) > 255) {
+ if ((disk_id << MSPRO_BLOCK_PART_SHIFT) > 255) {
rc = -ENOSPC;
goto out_release_id;
}
- msb->disk = alloc_disk(1 << MEMSTICK_PART_SHIFT);
+ msb->disk = alloc_disk(1 << MSPRO_BLOCK_PART_SHIFT);
if (!msb->disk) {
rc = -ENOMEM;
goto out_release_id;
MSPRO_BLOCK_MAX_PAGES * msb->page_size);
msb->disk->major = major;
- msb->disk->first_minor = disk_id << MEMSTICK_PART_SHIFT;
+ msb->disk->first_minor = disk_id << MSPRO_BLOCK_PART_SHIFT;
msb->disk->fops = &ms_block_bdops;
msb->usage_count = 1;
msb->disk->private_data = msb;
static struct memstick_device_id mspro_block_id_tbl[] = {
{MEMSTICK_MATCH_ALL, MEMSTICK_TYPE_PRO, MEMSTICK_CATEGORY_STORAGE_DUO,
- MEMSTICK_CLASS_GENERIC_DUO},
+ MEMSTICK_CLASS_DUO},
{}
};
#define TPC_CODE_SZ_MASK 0x00000700
#define TPC_DATA_SZ_MASK 0x00000007
+#define HOST_CONTROL_TDELAY_EN 0x00040000
+#define HOST_CONTROL_HW_OC_P 0x00010000
#define HOST_CONTROL_RESET_REQ 0x00008000
#define HOST_CONTROL_REI 0x00004000
#define HOST_CONTROL_LED 0x00000400
#define HOST_CONTROL_RESET 0x00000100
#define HOST_CONTROL_POWER_EN 0x00000080
#define HOST_CONTROL_CLOCK_EN 0x00000040
+#define HOST_CONTROL_REO 0x00000008
#define HOST_CONTROL_IF_SHIFT 4
#define HOST_CONTROL_IF_SERIAL 0x0
#define PAD_PU_PD_ON_MS_SOCK1 0x0f0f0000
#define CLOCK_CONTROL_40MHZ 0x00000001
-#define CLOCK_CONTROL_50MHZ 0x00000002
+#define CLOCK_CONTROL_50MHZ 0x0000000a
#define CLOCK_CONTROL_60MHZ 0x00000008
#define CLOCK_CONTROL_62_5MHZ 0x0000000c
#define CLOCK_CONTROL_OFF 0x00000000
+#define PCI_CTL_CLOCK_DLY_ADDR 0x000000b0
+#define PCI_CTL_CLOCK_DLY_MASK_A 0x00000f00
+#define PCI_CTL_CLOCK_DLY_MASK_B 0x0000f000
+
enum {
CMD_READY = 0x01,
FIFO_READY = 0x02,
return host->req->error;
}
- dev_dbg(&msh->dev, "control %08x\n",
- readl(host->addr + HOST_CONTROL));
+ dev_dbg(&msh->dev, "control %08x\n", readl(host->addr + HOST_CONTROL));
dev_dbg(&msh->dev, "status %08x\n", readl(host->addr + INT_STATUS));
dev_dbg(&msh->dev, "hstatus %08x\n", readl(host->addr + STATUS));
ndelay(20);
}
dev_dbg(&host->chip->pdev->dev, "reset_req timeout\n");
- return -EIO;
+ /* return -EIO; */
reset_next:
writel(HOST_CONTROL_RESET | HOST_CONTROL_CLOCK_EN
host_ctl = 7;
host_ctl |= HOST_CONTROL_POWER_EN
- | HOST_CONTROL_CLOCK_EN;
+ | HOST_CONTROL_CLOCK_EN
+ | HOST_CONTROL_HW_OC_P
+ | HOST_CONTROL_TDELAY_EN;
writel(host_ctl, host->addr + HOST_CONTROL);
writel(host->id ? PAD_PU_PD_ON_MS_SOCK1
break;
case MEMSTICK_INTERFACE:
host_ctl &= ~(3 << HOST_CONTROL_IF_SHIFT);
+ pci_read_config_dword(host->chip->pdev,
+ PCI_CTL_CLOCK_DLY_ADDR,
+ &clock_delay);
+ clock_delay &= host->id ? ~PCI_CTL_CLOCK_DLY_MASK_B
+ : ~PCI_CTL_CLOCK_DLY_MASK_A;
if (value == MEMSTICK_SERIAL) {
host_ctl &= ~HOST_CONTROL_FAST_CLK;
+ host_ctl &= ~HOST_CONTROL_REO;
host_ctl |= HOST_CONTROL_IF_SERIAL
<< HOST_CONTROL_IF_SHIFT;
host_ctl |= HOST_CONTROL_REI;
clock_ctl = CLOCK_CONTROL_40MHZ;
- clock_delay = 0;
} else if (value == MEMSTICK_PAR4) {
- host_ctl |= HOST_CONTROL_FAST_CLK;
+ host_ctl |= HOST_CONTROL_FAST_CLK | HOST_CONTROL_REO;
host_ctl |= HOST_CONTROL_IF_PAR4
<< HOST_CONTROL_IF_SHIFT;
host_ctl &= ~HOST_CONTROL_REI;
clock_ctl = CLOCK_CONTROL_40MHZ;
- clock_delay = 4;
+ clock_delay |= host->id ? (4 << 12) : (4 << 8);
} else if (value == MEMSTICK_PAR8) {
host_ctl |= HOST_CONTROL_FAST_CLK;
host_ctl |= HOST_CONTROL_IF_PAR8
<< HOST_CONTROL_IF_SHIFT;
- host_ctl &= ~HOST_CONTROL_REI;
- clock_ctl = CLOCK_CONTROL_60MHZ;
- clock_delay = 0;
+ host_ctl &= ~(HOST_CONTROL_REI | HOST_CONTROL_REO);
+ clock_ctl = CLOCK_CONTROL_50MHZ;
} else
return -EINVAL;
+
writel(host_ctl, host->addr + HOST_CONTROL);
writel(clock_ctl, host->addr + CLOCK_CONTROL);
- writel(clock_delay, host->addr + CLOCK_DELAY);
+ pci_write_config_dword(host->chip->pdev,
+ PCI_CTL_CLOCK_DLY_ADDR,
+ clock_delay);
break;
};
return 0;
int order = get_order(sizeof(struct gru_state) *
GRU_CHIPLETS_PER_BLADE);
+ if (!IS_UV())
+ return;
+
for (i = 0; i < GRU_CHIPLETS_PER_BLADE; i++)
free_irq(IRQ_GRU + i, NULL);
static int __init mmc_blk_init(void)
{
- int res = -ENOMEM;
+ int res;
res = register_blkdev(MMC_BLOCK_MAJOR, "mmc");
if (res)
goto out;
- return mmc_register_driver(&mmc_driver);
+ res = mmc_register_driver(&mmc_driver);
+ if (res)
+ goto out2;
+ return 0;
+ out2:
+ unregister_blkdev(MMC_BLOCK_MAJOR, "mmc");
out:
return res;
}
};
-static struct mutex mmc_test_lock;
+static DEFINE_MUTEX(mmc_test_lock);
static void mmc_test_run(struct mmc_test_card *test, int testcase)
{
if ((card->type != MMC_TYPE_MMC) && (card->type != MMC_TYPE_SD))
return -ENODEV;
- mutex_init(&mmc_test_lock);
-
ret = device_create_file(&card->dev, &dev_attr_test);
if (ret)
return ret;
/* Grab a more or less consistent snapshot */
spin_lock_irq(&host->mmc->lock);
+ clk_enable(host->mck);
memcpy_fromio(buf, host->regs, MCI_REGS_SIZE);
+ clk_disable(host->mck);
spin_unlock_irq(&host->mmc->lock);
seq_printf(s, "MR:\t0x%08x%s%s CLKDIV=%u\n",
atmci_show_status_reg(s, "SR", buf[MCI_SR / 4]);
atmci_show_status_reg(s, "IMR", buf[MCI_IMR / 4]);
+ kfree(buf);
+
return 0;
}
struct mmc_host *mmc;
struct dentry *root;
struct dentry *node;
- struct resource *res;
mmc = host->mmc;
root = mmc->debugfs_root;
if (!node)
goto err;
- res = platform_get_resource(host->pdev, IORESOURCE_MEM, 0);
- node->d_inode->i_size = res->end - res->start + 1;
-
node = debugfs_create_file("req", S_IRUSR, root, host, &atmci_req_fops);
if (!node)
goto err;
host->present = !gpio_get_value(host->detect_pin);
}
}
+
+ if (!gpio_is_valid(host->detect_pin))
+ mmc->caps |= MMC_CAP_NEEDS_POLL;
+
if (gpio_is_valid(host->wp_pin)) {
if (gpio_request(host->wp_pin, "mmc_wp")) {
dev_dbg(&mmc->class_dev, "no WP pin available\n");
#define STATUS_TO_TEXT(a) \
do { \
if (status & TMIO_STAT_##a) \
- printf(#a); \
+ printk(#a); \
} while (0)
-void debug_status(u32 status)
+void pr_debug_status(u32 status)
{
printk(KERN_DEBUG "status: %08x = ", status);
STATUS_TO_TEXT(CARD_REMOVE);
struct bnx2_irq {
irq_handler_t handler;
- u16 vector;
+ unsigned int vector;
u8 requested;
char name[16];
};
nic->flags |= wol_magic;
/* ack any pending wake events, disable PME */
- err = pci_enable_wake(pdev, 0, 0);
- if (err)
- DPRINTK(PROBE, ERR, "Error clearing wake event\n");
+ pci_pme_active(pdev, false);
strcpy(netdev->name, "eth%d");
if((err = register_netdev(netdev))) {
static u8 e1000_calculate_mng_checksum(char *buffer, u32 length);
static s32 e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, u16 duplex);
static s32 e1000_configure_kmrn_for_1000(struct e1000_hw *hw);
+static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
+static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
/* IGP cable length table */
static const
83, 89, 95, 100, 105, 109, 113, 116, 119, 122, 124,
104, 109, 114, 118, 121, 124};
+static DEFINE_SPINLOCK(e1000_eeprom_lock);
+
/******************************************************************************
* Set the phy type member in the hw struct.
*
* words - number of words to read
*****************************************************************************/
s32 e1000_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ s32 ret;
+ spin_lock(&e1000_eeprom_lock);
+ ret = e1000_do_read_eeprom(hw, offset, words, data);
+ spin_unlock(&e1000_eeprom_lock);
+ return ret;
+}
+
+static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
{
struct e1000_eeprom_info *eeprom = &hw->eeprom;
u32 i = 0;
* EEPROM will most likely contain an invalid checksum.
*****************************************************************************/
s32 e1000_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ s32 ret;
+ spin_lock(&e1000_eeprom_lock);
+ ret = e1000_do_write_eeprom(hw, offset, words, data);
+ spin_unlock(&e1000_eeprom_lock);
+ return ret;
+}
+
+
+static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
{
struct e1000_eeprom_info *eeprom = &hw->eeprom;
s32 status = 0;
dev->dev_addr[4] = (np->orig_mac[0] >> 8) & 0xff;
dev->dev_addr[5] = (np->orig_mac[0] >> 0) & 0xff;
writel(txreg|NVREG_TRANSMITPOLL_MAC_ADDR_REV, base + NvRegTransmitPoll);
+ printk(KERN_DEBUG "nv_probe: set workaround bit for reversed mac addr\n");
}
memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
}
}
-static void __devexit nv_remove(struct pci_dev *pci_dev)
+static void nv_restore_mac_addr(struct pci_dev *pci_dev)
{
struct net_device *dev = pci_get_drvdata(pci_dev);
struct fe_priv *np = netdev_priv(dev);
u8 __iomem *base = get_hwbase(dev);
- unregister_netdev(dev);
-
/* special op: write back the misordered MAC address - otherwise
* the next nv_probe would see a wrong address.
*/
writel(np->orig_mac[1], base + NvRegMacAddrB);
writel(readl(base + NvRegTransmitPoll) & ~NVREG_TRANSMITPOLL_MAC_ADDR_REV,
base + NvRegTransmitPoll);
+}
+
+static void __devexit nv_remove(struct pci_dev *pci_dev)
+{
+ struct net_device *dev = pci_get_drvdata(pci_dev);
+
+ unregister_netdev(dev);
+
+ nv_restore_mac_addr(pci_dev);
/* restore any phy related changes */
nv_restore_phy(dev);
Code Review / linux-2.6.git / commitdiff