* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: Fix wrong condition check in while loop for mailbox and iommu2
omap: rng: Use resource_size instead of manual calculation
omap: Fix MMC gpio_wp for BeagleBoard C2 and above
omap: Fix matrix_keymap_data usage
omap: Fix a OMAP_MPUIO_VBASE typo for 850
omap: Fix wrong jtag_id for 850
omap: iovmm: Fix compiler warning
omap: mailbox: Flush posted write when acking mailbox irq
omap: mailbox: Execute softreset at startup
omap: Add missing mux pin for EHCI phy reset line
omap: Fix 44xx compile
omap: Fix mcspi compile for 2420
omap: Fix compile for arch/arm/mach-omap2
--- /dev/null
+ARM TCM (Tightly-Coupled Memory) handling in Linux
+----
+Written by Linus Walleij <linus.walleij@stericsson.com>
+
+Some ARM SoC:s have a so-called TCM (Tightly-Coupled Memory).
+This is usually just a few (4-64) KiB of RAM inside the ARM
+processor.
+
+Due to being embedded inside the CPU The TCM has a
+Harvard-architecture, so there is an ITCM (instruction TCM)
+and a DTCM (data TCM). The DTCM can not contain any
+instructions, but the ITCM can actually contain data.
+The size of DTCM or ITCM is minimum 4KiB so the typical
+minimum configuration is 4KiB ITCM and 4KiB DTCM.
+
+ARM CPU:s have special registers to read out status, physical
+location and size of TCM memories. arch/arm/include/asm/cputype.h
+defines a CPUID_TCM register that you can read out from the
+system control coprocessor. Documentation from ARM can be found
+at http://infocenter.arm.com, search for "TCM Status Register"
+to see documents for all CPUs. Reading this register you can
+determine if ITCM (bit 0) and/or DTCM (bit 16) is present in the
+machine.
+
+There is further a TCM region register (search for "TCM Region
+Registers" at the ARM site) that can report and modify the location
+size of TCM memories at runtime. This is used to read out and modify
+TCM location and size. Notice that this is not a MMU table: you
+actually move the physical location of the TCM around. At the
+place you put it, it will mask any underlying RAM from the
+CPU so it is usually wise not to overlap any physical RAM with
+the TCM. The TCM memory exists totally outside the MMU and will
+override any MMU mappings.
+
+Code executing inside the ITCM does not "see" any MMU mappings
+and e.g. register accesses must be made to physical addresses.
+
+TCM is used for a few things:
+
+- FIQ and other interrupt handlers that need deterministic
+ timing and cannot wait for cache misses.
+
+- Idle loops where all external RAM is set to self-refresh
+ retention mode, so only on-chip RAM is accessible by
+ the CPU and then we hang inside ITCM waiting for an
+ interrupt.
+
+- Other operations which implies shutting off or reconfiguring
+ the external RAM controller.
+
+There is an interface for using TCM on the ARM architecture
+in <asm/tcm.h>. Using this interface it is possible to:
+
+- Define the physical address and size of ITCM and DTCM.
+
+- Tag functions to be compiled into ITCM.
+
+- Tag data and constants to be allocated to DTCM and ITCM.
+
+- Have the remaining TCM RAM added to a special
+ allocation pool with gen_pool_create() and gen_pool_add()
+ and provice tcm_alloc() and tcm_free() for this
+ memory. Such a heap is great for things like saving
+ device state when shutting off device power domains.
+
+A machine that has TCM memory shall select HAVE_TCM in
+arch/arm/Kconfig for itself, and then the
+rest of the functionality will depend on the physical
+location and size of ITCM and DTCM to be defined in
+mach/memory.h for the machine. Code that needs to use
+TCM shall #include <asm/tcm.h> If the TCM is not located
+at the place given in memory.h it will be moved using
+the TCM Region registers.
+
+Functions to go into itcm can be tagged like this:
+int __tcmfunc foo(int bar);
+
+Variables to go into dtcm can be tagged like this:
+int __tcmdata foo;
+
+Constants can be tagged like this:
+int __tcmconst foo;
+
+To put assembler into TCM just use
+.section ".tcm.text" or .section ".tcm.data"
+respectively.
+
+Example code:
+
+#include <asm/tcm.h>
+
+/* Uninitialized data */
+static u32 __tcmdata tcmvar;
+/* Initialized data */
+static u32 __tcmdata tcmassigned = 0x2BADBABEU;
+/* Constant */
+static const u32 __tcmconst tcmconst = 0xCAFEBABEU;
+
+static void __tcmlocalfunc tcm_to_tcm(void)
+{
+ int i;
+ for (i = 0; i < 100; i++)
+ tcmvar ++;
+}
+
+static void __tcmfunc hello_tcm(void)
+{
+ /* Some abstract code that runs in ITCM */
+ int i;
+ for (i = 0; i < 100; i++) {
+ tcmvar ++;
+ }
+ tcm_to_tcm();
+}
+
+static void __init test_tcm(void)
+{
+ u32 *tcmem;
+ int i;
+
+ hello_tcm();
+ printk("Hello TCM executed from ITCM RAM\n");
+
+ printk("TCM variable from testrun: %u @ %p\n", tcmvar, &tcmvar);
+ tcmvar = 0xDEADBEEFU;
+ printk("TCM variable: 0x%x @ %p\n", tcmvar, &tcmvar);
+
+ printk("TCM assigned variable: 0x%x @ %p\n", tcmassigned, &tcmassigned);
+
+ printk("TCM constant: 0x%x @ %p\n", tcmconst, &tcmconst);
+
+ /* Allocate some TCM memory from the pool */
+ tcmem = tcm_alloc(20);
+ if (tcmem) {
+ printk("TCM Allocated 20 bytes of TCM @ %p\n", tcmem);
+ tcmem[0] = 0xDEADBEEFU;
+ tcmem[1] = 0x2BADBABEU;
+ tcmem[2] = 0xCAFEBABEU;
+ tcmem[3] = 0xDEADBEEFU;
+ tcmem[4] = 0x2BADBABEU;
+ for (i = 0; i < 5; i++)
+ printk("TCM tcmem[%d] = %08x\n", i, tcmem[i]);
+ tcm_free(tcmem, 20);
+ }
+}
Not all bits in the mask can be modified. Not all bits that can be
modified do anything. Not all hot keys can be individually controlled
-by the mask. Some models do not support the mask at all, and in those
-models, hot keys cannot be controlled individually. The behaviour of
-the mask is, therefore, highly dependent on the ThinkPad model.
+by the mask. Some models do not support the mask at all. The behaviour
+of the mask is, therefore, highly dependent on the ThinkPad model.
+
+The driver will filter out any unmasked hotkeys, so even if the firmware
+doesn't allow disabling an specific hotkey, the driver will not report
+events for unmasked hotkeys.
Note that unmasking some keys prevents their default behavior. For
example, if Fn+F5 is unmasked, that key will no longer enable/disable
-Bluetooth by itself.
+Bluetooth by itself in firmware.
-Note also that not all Fn key combinations are supported through ACPI.
-For example, on the X40, the brightness, volume and "Access IBM" buttons
-do not generate ACPI events even with this driver. They *can* be used
-through the "ThinkPad Buttons" utility, see http://www.nongnu.org/tpb/
+Note also that not all Fn key combinations are supported through ACPI
+depending on the ThinkPad model and firmware version. On those
+ThinkPads, it is still possible to support some extra hotkeys by
+polling the "CMOS NVRAM" at least 10 times per second. The driver
+attempts to enables this functionality automatically when required.
procfs notes:
1: does nothing
hotkey_mask:
- bit mask to enable driver-handling (and depending on
+ bit mask to enable reporting (and depending on
the firmware, ACPI event generation) for each hot key
(see above). Returns the current status of the hot keys
mask, and allows one to modify it.
- Note: when NVRAM polling is active, the firmware mask
- will be different from the value returned by
- hotkey_mask. The driver will retain enabled bits for
- hotkeys that are under NVRAM polling even if the
- firmware refuses them, and will not set these bits on
- the firmware hot key mask.
-
hotkey_all_mask:
bit mask that should enable event reporting for all
supported hot keys, when echoed to hotkey_mask above.
bit mask that should enable event reporting for all
supported hot keys, except those which are always
handled by the firmware anyway. Echo it to
- hotkey_mask above, to use.
+ hotkey_mask above, to use. This is the default mask
+ used by the driver.
hotkey_source_mask:
bit mask that selects which hot keys will the driver
based on the capabilities reported by the ACPI firmware,
but it can be overridden at runtime.
- Hot keys whose bits are set in both hotkey_source_mask
- and also on hotkey_mask are polled for in NVRAM. Only a
- few hot keys are available through CMOS NVRAM polling.
+ Hot keys whose bits are set in hotkey_source_mask are
+ polled for in NVRAM, and reported as hotkey events if
+ enabled in hotkey_mask. Only a few hot keys are
+ available through CMOS NVRAM polling.
Warning: when in NVRAM mode, the volume up/down/mute
keys are synthesized according to changes in the mixer,
0x2305 System is waking up from suspend to eject bay
0x2404 System is waking up from hibernation to undock
0x2405 System is waking up from hibernation to eject bay
+0x5010 Brightness level changed/control event
The above events are never propagated by the driver.
0x4003 Undocked (see 0x2x04), can sleep again
0x500B Tablet pen inserted into its storage bay
0x500C Tablet pen removed from its storage bay
-0x5010 Brightness level changed (newer Lenovo BIOSes)
The above events are propagated by the driver.
2. Do *NOT* load up ACPI video, enable the hotkeys in thinkpad-acpi,
and map them to KEY_BRIGHTNESS_UP and KEY_BRIGHTNESS_DOWN. Process
these keys on userspace somehow (e.g. by calling xbacklight).
+ The driver will do this automatically if it detects that ACPI video
+ has been disabled.
Bluetooth
0x020400: Marker for 16 LEDs support. Also, LEDs that are known
to not exist in a given model are not registered with
the LED sysfs class anymore.
+
+0x020500: Updated hotkey driver, hotkey_mask is always available
+ and it is always able to disable hot keys. Very old
+ thinkpads are properly supported. hotkey_bios_mask
+ is deprecated and marked for removal.
ARM/INTEL IXP4XX ARM ARCHITECTURE
M: Imre Kaloz <kaloz@openwrt.org>
M: Krzysztof Halasa <khc@pm.waw.pl>
-L: linux-arm-kernel@lists.infradead.org
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/mach-ixp4xx/
M: Dirk Opfer <dirk@opfer-online.de>
S: Maintained
-ARM/PALMTX,PALMT5,PALMLD,PALMTE2 SUPPORT
-M: Marek Vasut <marek.vasut@gmail.com>
+ARM/PALMTX,PALMT5,PALMLD,PALMTE2,PALMTC SUPPORT
+P: Marek Vasut
+M: marek.vasut@gmail.com
+L: linux-arm-kernel@lists.infradead.org
W: http://hackndev.com
S: Maintained
ARM/PALM TREO 680 SUPPORT
M: Tomas Cech <sleep_walker@suse.cz>
+L: linux-arm-kernel@lists.infradead.org
W: http://hackndev.com
S: Maintained
ARM/PALMZ72 SUPPORT
M: Sergey Lapin <slapin@ossfans.org>
+L: linux-arm-kernel@lists.infradead.org
W: http://hackndev.com
S: Maintained
VERSION = 2
PATCHLEVEL = 6
-SUBLEVEL = 31
-EXTRAVERSION =
+SUBLEVEL = 32
+EXTRAVERSION = -rc2
NAME = Man-Eating Seals of Antiquity
# *DOCUMENTATION*
struct task_struct init_task = INIT_TASK(init_task);
EXPORT_SYMBOL(init_task);
-union thread_union init_thread_union
- __attribute__((section(".data.init_thread")))
- = { INIT_THREAD_INFO(init_task) };
+union thread_union init_thread_union __init_task_data =
+ { INIT_THREAD_INFO(init_task) };
#include <asm-generic/vmlinux.lds.h>
+#include <asm/thread_info.h>
#include <asm/page.h>
OUTPUT_FORMAT("elf64-alpha")
} :kernel
RODATA
-
- /* Exception table */
- . = ALIGN(16);
- __ex_table : {
- __start___ex_table = .;
- *(__ex_table)
- __stop___ex_table = .;
- }
+ EXCEPTION_TABLE(16)
/* Will be freed after init */
- . = ALIGN(PAGE_SIZE);
- /* Init code and data */
- __init_begin = .;
- .init.text : {
- _sinittext = .;
- INIT_TEXT
- _einittext = .;
- }
- .init.data : {
- INIT_DATA
- }
-
- . = ALIGN(16);
- .init.setup : {
- __setup_start = .;
- *(.init.setup)
- __setup_end = .;
- }
-
- . = ALIGN(8);
- .initcall.init : {
- __initcall_start = .;
- INITCALLS
- __initcall_end = .;
- }
-
-#ifdef CONFIG_BLK_DEV_INITRD
- . = ALIGN(PAGE_SIZE);
- .init.ramfs : {
- __initramfs_start = .;
- *(.init.ramfs)
- __initramfs_end = .;
- }
-#endif
-
- . = ALIGN(8);
- .con_initcall.init : {
- __con_initcall_start = .;
- *(.con_initcall.init)
- __con_initcall_end = .;
- }
-
- . = ALIGN(8);
- SECURITY_INIT
-
+ __init_begin = ALIGN(PAGE_SIZE);
+ INIT_TEXT_SECTION(PAGE_SIZE)
+ INIT_DATA_SECTION(16)
PERCPU(PAGE_SIZE)
-
- . = ALIGN(2 * PAGE_SIZE);
+ /* Align to THREAD_SIZE rather than PAGE_SIZE here so any padding page
+ needed for the THREAD_SIZE aligned init_task gets freed after init */
+ . = ALIGN(THREAD_SIZE);
__init_end = .;
/* Freed after init ends here */
- /* Note 2 page alignment above. */
- .data.init_thread : {
- *(.data.init_thread)
- }
-
- . = ALIGN(PAGE_SIZE);
- .data.page_aligned : {
- *(.data.page_aligned)
- }
-
- . = ALIGN(64);
- .data.cacheline_aligned : {
- *(.data.cacheline_aligned)
- }
-
_data = .;
- /* Data */
- .data : {
- DATA_DATA
- CONSTRUCTORS
- }
+ RW_DATA_SECTION(64, PAGE_SIZE, THREAD_SIZE)
.got : {
*(.got)
}
_edata = .; /* End of data section */
- __bss_start = .;
- .sbss : {
- *(.sbss)
- *(.scommon)
- }
- .bss : {
- *(.bss)
- *(COMMON)
- }
- __bss_stop = .;
+ BSS_SECTION(0, 0, 0)
_end = .;
.mdebug 0 : {
depends on GENERIC_CLOCKEVENTS
default y if SMP && !LOCAL_TIMERS
+config HAVE_TCM
+ bool
+ select GENERIC_ALLOCATOR
+
config NO_IOPORT
bool
bool "ST-Ericsson U300 Series"
depends on MMU
select CPU_ARM926T
+ select HAVE_TCM
select ARM_AMBA
select ARM_VIC
select GENERIC_TIME
spin_unlock_irqrestore(&lchip->lock, flags);
}
+EXPORT_SYMBOL(locomo_gpio_set_dir);
int locomo_gpio_read_level(struct device *dev, unsigned int bits)
{
ret &= bits;
return ret;
}
+EXPORT_SYMBOL(locomo_gpio_read_level);
int locomo_gpio_read_output(struct device *dev, unsigned int bits)
{
ret &= bits;
return ret;
}
+EXPORT_SYMBOL(locomo_gpio_read_output);
void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set)
{
spin_unlock_irqrestore(&lchip->lock, flags);
}
+EXPORT_SYMBOL(locomo_gpio_write);
static void locomo_m62332_sendbit(void *mapbase, int bit)
{
spin_unlock_irqrestore(&lchip->lock, flags);
}
+EXPORT_SYMBOL(locomo_m62332_senddata);
/*
* Frontlight control
*/
-static struct locomo *locomo_chip_driver(struct locomo_dev *ldev);
-
void locomo_frontlight_set(struct locomo_dev *dev, int duty, int vr, int bpwf)
{
unsigned long flags;
driver->drv.bus = &locomo_bus_type;
return driver_register(&driver->drv);
}
+EXPORT_SYMBOL(locomo_driver_register);
void locomo_driver_unregister(struct locomo_driver *driver)
{
driver_unregister(&driver->drv);
}
+EXPORT_SYMBOL(locomo_driver_unregister);
static int __init locomo_init(void)
{
MODULE_DESCRIPTION("Sharp LoCoMo core driver");
MODULE_LICENSE("GPL");
MODULE_AUTHOR("John Lenz <lenz@cs.wisc.edu>");
-
-EXPORT_SYMBOL(locomo_driver_register);
-EXPORT_SYMBOL(locomo_driver_unregister);
-EXPORT_SYMBOL(locomo_gpio_set_dir);
-EXPORT_SYMBOL(locomo_gpio_read_level);
-EXPORT_SYMBOL(locomo_gpio_read_output);
-EXPORT_SYMBOL(locomo_gpio_write);
-EXPORT_SYMBOL(locomo_m62332_senddata);
#include <linux/list.h>
#include <linux/io.h>
#include <linux/sysdev.h>
+#include <linux/device.h>
#include <linux/amba/bus.h>
#include <asm/mach/irq.h>
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.24-rc5
-# Fri Dec 21 11:06:19 2007
-#
-CONFIG_ARM=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_TIME=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ZONE_DMA=y
-CONFIG_ARCH_MTD_XIP=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# General setup
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_LOCK_KERNEL=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
-# CONFIG_RELAY is not set
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_SYSCTL=y
-# CONFIG_EMBEDDED is not set
-CONFIG_UID16=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_ALL is not set
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
-CONFIG_EPOLL=y
-CONFIG_SIGNALFD=y
-CONFIG_EVENTFD=y
-CONFIG_SHMEM=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLAB=y
-# CONFIG_SLUB is not set
-# CONFIG_SLOB is not set
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_MODVERSIONS is not set
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-# CONFIG_BLK_DEV_BSG is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_DEFAULT_AS is not set
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-
-#
-# System Type
-#
-# CONFIG_ARCH_AAEC2000 is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_REALVIEW is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_NETX is not set
-# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP13XX is not set
-# CONFIG_ARCH_IOP32X is not set
-# CONFIG_ARCH_IOP33X is not set
-# CONFIG_ARCH_IXP23XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_L7200 is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
-# CONFIG_ARCH_MXC is not set
-# CONFIG_ARCH_PNX4008 is not set
-CONFIG_ARCH_PXA=y
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-# CONFIG_ARCH_DAVINCI is not set
-# CONFIG_ARCH_OMAP is not set
-
-#
-# Intel PXA2xx/PXA3xx Implementations
-#
-
-#
-# Supported PXA3xx Processor Variants
-#
-CONFIG_CPU_PXA300=y
-CONFIG_CPU_PXA310=y
-# CONFIG_CPU_PXA320 is not set
-# CONFIG_ARCH_LUBBOCK is not set
-# CONFIG_MACH_LOGICPD_PXA270 is not set
-# CONFIG_MACH_MAINSTONE is not set
-# CONFIG_ARCH_PXA_IDP is not set
-# CONFIG_PXA_SHARPSL is not set
-# CONFIG_MACH_TRIZEPS4 is not set
-# CONFIG_MACH_EM_X270 is not set
-# CONFIG_MACH_ZYLONITE is not set
-CONFIG_MACH_LITTLETON=y
-# CONFIG_MACH_ARMCORE is not set
-CONFIG_PXA3xx=y
-CONFIG_PXA_SSP=y
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
-
-#
-# Processor Type
-#
-CONFIG_CPU_32=y
-CONFIG_CPU_XSC3=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_IO_36=y
-
-#
-# Processor Features
-#
-# CONFIG_ARM_THUMB is not set
-# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
-CONFIG_IWMMXT=y
-
-#
-# Bus support
-#
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-CONFIG_TICK_ONESHOT=y
-# CONFIG_NO_HZ is not set
-# CONFIG_HIGH_RES_TIMERS is not set
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_PREEMPT=y
-CONFIG_HZ=100
-CONFIG_AEABI=y
-CONFIG_OABI_COMPAT=y
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
-CONFIG_VIRT_TO_BUS=y
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS2,38400 mem=64M"
-# CONFIG_XIP_KERNEL is not set
-# CONFIG_KEXEC is not set
-
-#
-# CPU Frequency scaling
-#
-# CONFIG_CPU_FREQ is not set
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-CONFIG_FPE_NWFPE=y
-# CONFIG_FPE_NWFPE_XP is not set
-# CONFIG_FPE_FASTFPE is not set
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_AOUT is not set
-# CONFIG_BINFMT_MISC is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-CONFIG_SUSPEND_UP_POSSIBLE=y
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-CONFIG_XFRM=y
-# CONFIG_XFRM_USER is not set
-# CONFIG_XFRM_SUB_POLICY is not set
-# CONFIG_XFRM_MIGRATE is not set
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-# CONFIG_IP_PNP_DHCP is not set
-# CONFIG_IP_PNP_BOOTP is not set
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_INET_XFRM_MODE_TRANSPORT=y
-CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
-# CONFIG_INET_LRO is not set
-CONFIG_INET_DIAG=y
-CONFIG_INET_TCP_DIAG=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
-# CONFIG_IP_DCCP is not set
-# CONFIG_IP_SCTP is not set
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
-# CONFIG_RFKILL is not set
-# CONFIG_NET_9P is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-# CONFIG_STANDALONE is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-CONFIG_FW_LOADER=y
-# CONFIG_DEBUG_DRIVER is not set
-# CONFIG_DEBUG_DEVRES is not set
-# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
-# CONFIG_PARPORT is not set
-# CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SCSI_NETLINK is not set
-# CONFIG_ATA is not set
-# CONFIG_MD is not set
-CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_MACVLAN is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-# CONFIG_VETH is not set
-# CONFIG_PHYLIB is not set
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_AX88796 is not set
-CONFIG_SMC91X=y
-# CONFIG_DM9000 is not set
-# CONFIG_SMC911X is not set
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_B44 is not set
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_ISDN is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-# CONFIG_INPUT_POLLDEV is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TABLET is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_PXA=y
-CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_IPMI_HANDLER is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-# CONFIG_WATCHDOG is not set
-
-#
-# Sonics Silicon Backplane
-#
-CONFIG_SSB_POSSIBLE=y
-# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_SM501 is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_DAB is not set
-
-#
-# Graphics support
-#
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-CONFIG_FB=y
-# CONFIG_FIRMWARE_EDID is not set
-# CONFIG_FB_DDC is not set
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
-# CONFIG_FB_SYS_FILLRECT is not set
-# CONFIG_FB_SYS_COPYAREA is not set
-# CONFIG_FB_SYS_IMAGEBLIT is not set
-# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
-# CONFIG_FB_SVGALIB is not set
-# CONFIG_FB_MACMODES is not set
-# CONFIG_FB_BACKLIGHT is not set
-# CONFIG_FB_MODE_HELPERS is not set
-# CONFIG_FB_TILEBLITTING is not set
-
-#
-# Frame buffer hardware drivers
-#
-# CONFIG_FB_S1D13XXX is not set
-CONFIG_FB_PXA=y
-# CONFIG_FB_PXA_PARAMETERS is not set
-# CONFIG_FB_MBX is not set
-# CONFIG_FB_VIRTUAL is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FONTS=y
-# CONFIG_FONT_8x8 is not set
-CONFIG_FONT_8x16=y
-# CONFIG_FONT_6x11 is not set
-# CONFIG_FONT_7x14 is not set
-# CONFIG_FONT_PEARL_8x8 is not set
-# CONFIG_FONT_ACORN_8x8 is not set
-# CONFIG_FONT_MINI_4x6 is not set
-# CONFIG_FONT_SUN8x16 is not set
-# CONFIG_FONT_SUN12x22 is not set
-# CONFIG_FONT_10x18 is not set
-CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_MONO=y
-CONFIG_LOGO_LINUX_VGA16=y
-CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
-
-#
-# File systems
-#
-# CONFIG_EXT2_FS is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_INOTIFY is not set
-# CONFIG_QUOTA is not set
-# CONFIG_DNOTIFY is not set
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-CONFIG_NETWORK_FILESYSTEMS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_DIRECTIO=y
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_NFS_ACL_SUPPORT=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-CONFIG_SUNRPC_GSS=y
-# CONFIG_SUNRPC_BIND34 is not set
-CONFIG_RPCSEC_GSS_KRB5=y
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_NLS is not set
-# CONFIG_DLM is not set
-# CONFIG_INSTRUMENTATION is not set
-
-#
-# Kernel hacking
-#
-CONFIG_PRINTK_TIME=y
-CONFIG_ENABLE_WARN_DEPRECATED=y
-CONFIG_ENABLE_MUST_CHECK=y
-CONFIG_MAGIC_SYSRQ=y
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_DETECT_SOFTLOCKUP=y
-CONFIG_SCHED_DEBUG=y
-# CONFIG_SCHEDSTATS is not set
-# CONFIG_TIMER_STATS is not set
-# CONFIG_DEBUG_SLAB is not set
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_DEBUG_RT_MUTEXES is not set
-# CONFIG_RT_MUTEX_TESTER is not set
-# CONFIG_DEBUG_SPINLOCK is not set
-# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_LOCK_ALLOC is not set
-# CONFIG_PROVE_LOCKING is not set
-# CONFIG_LOCK_STAT is not set
-# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
-# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
-# CONFIG_DEBUG_KOBJECT is not set
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_DEBUG_INFO=y
-# CONFIG_DEBUG_VM is not set
-# CONFIG_DEBUG_LIST is not set
-# CONFIG_DEBUG_SG is not set
-CONFIG_FRAME_POINTER=y
-CONFIG_FORCED_INLINING=y
-# CONFIG_BOOT_PRINTK_DELAY is not set
-# CONFIG_RCU_TORTURE_TEST is not set
-# CONFIG_FAULT_INJECTION is not set
-# CONFIG_SAMPLES is not set
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-CONFIG_DEBUG_LL=y
-# CONFIG_DEBUG_ICEDCC is not set
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_MANAGER=y
-# CONFIG_CRYPTO_HMAC is not set
-# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
-# CONFIG_CRYPTO_SHA1 is not set
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
-# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_ECB is not set
-CONFIG_CRYPTO_CBC=y
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_AES is not set
-# CONFIG_CRYPTO_CAST5 is not set
-# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
-# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_SEED is not set
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
-CONFIG_CRYPTO_HW=y
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-CONFIG_CRC_CCITT=y
-# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
-CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.31-rc1
+# Mon Jul 13 22:48:49 2009
+#
+CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+# CONFIG_CLASSIC_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=18
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+
+#
+# Performance Counters
+#
+CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
+CONFIG_COMPAT_BRK=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+# CONFIG_MODULE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+
+#
+# Intel PXA2xx/PXA3xx Implementations
+#
+
+#
+# Supported PXA3xx Processor Variants
+#
+CONFIG_CPU_PXA300=y
+CONFIG_CPU_PXA310=y
+CONFIG_CPU_PXA320=y
+CONFIG_CPU_PXA930=y
+CONFIG_CPU_PXA935=y
+# CONFIG_ARCH_GUMSTIX is not set
+# CONFIG_MACH_INTELMOTE2 is not set
+# CONFIG_MACH_STARGATE2 is not set
+# CONFIG_ARCH_LUBBOCK is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_MACH_MP900C is not set
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_PXA_SHARPSL is not set
+# CONFIG_ARCH_VIPER is not set
+# CONFIG_ARCH_PXA_ESERIES is not set
+# CONFIG_TRIZEPS_PXA is not set
+# CONFIG_MACH_H5000 is not set
+# CONFIG_MACH_EM_X270 is not set
+# CONFIG_MACH_EXEDA is not set
+# CONFIG_MACH_COLIBRI is not set
+# CONFIG_MACH_COLIBRI300 is not set
+# CONFIG_MACH_COLIBRI320 is not set
+CONFIG_MACH_ZYLONITE=y
+CONFIG_MACH_LITTLETON=y
+CONFIG_MACH_TAVOREVB=y
+CONFIG_MACH_SAAR=y
+# CONFIG_MACH_ARMCORE is not set
+# CONFIG_MACH_CM_X300 is not set
+# CONFIG_MACH_H4700 is not set
+# CONFIG_MACH_MAGICIAN is not set
+# CONFIG_MACH_HIMALAYA is not set
+# CONFIG_MACH_MIOA701 is not set
+# CONFIG_MACH_PCM027 is not set
+# CONFIG_ARCH_PXA_PALM is not set
+# CONFIG_MACH_CSB726 is not set
+# CONFIG_PXA_EZX is not set
+CONFIG_PXA3xx=y
+CONFIG_PXA_SSP=y
+CONFIG_PXA_HAVE_BOARD_IRQS=y
+CONFIG_PLAT_PXA=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_XSC3=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_IO_36=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_OUTER_CACHE=y
+CONFIG_CACHE_XSC3L2=y
+CONFIG_IWMMXT=y
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PREEMPT=y
+CONFIG_HZ=100
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=64M debug"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_VERIFY_WRITE=y
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_H1900 is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_SHARPSL is not set
+CONFIG_MTD_NAND_PXA3xx=y
+CONFIG_MTD_NAND_PXA3xx_BUILTIN=y
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+CONFIG_MTD_ONENAND=y
+CONFIG_MTD_ONENAND_VERIFY_WRITE=y
+CONFIG_MTD_ONENAND_GENERIC=y
+# CONFIG_MTD_ONENAND_OTP is not set
+# CONFIG_MTD_ONENAND_2X_PROGRAM is not set
+# CONFIG_MTD_ONENAND_SIM is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+CONFIG_SMC91X=y
+# CONFIG_DM9000 is not set
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+CONFIG_KEYBOARD_PXA27x=y
+CONFIG_KEYBOARD_PXA930_ROTARY=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_ELANTECH is not set
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_MOUSE_GPIO is not set
+CONFIG_MOUSE_PXA930_TRKBALL=y
+# CONFIG_MOUSE_SYNAPTICS_I2C is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_TOUCHSCREEN_ADS7846 is not set
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+CONFIG_TOUCHSCREEN_DA9034=y
+# CONFIG_TOUCHSCREEN_EETI is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_CHARDEV is not set
+# CONFIG_I2C_HELPER_AUTO is not set
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_PXA=y
+# CONFIG_I2C_PXA_SLAVE is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_PXA2XX=y
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+CONFIG_GPIO_MAX732X=y
+CONFIG_GPIO_PCA953X=y
+CONFIG_GPIO_PCF857X=y
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+CONFIG_GPIO_MAX7301=y
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_W1 is not set
+CONFIG_POWER_SUPPLY=y
+CONFIG_POWER_SUPPLY_DEBUG=y
+CONFIG_PDA_POWER=y
+# CONFIG_BATTERY_DS2760 is not set
+# CONFIG_BATTERY_BQ27x00 is not set
+CONFIG_BATTERY_DA9030=y
+# CONFIG_BATTERY_MAX17040 is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+CONFIG_PMIC_DA903X=y
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_PXA=y
+# CONFIG_FB_PXA_OVERLAY is not set
+# CONFIG_FB_PXA_SMARTPANEL is not set
+# CONFIG_FB_PXA_PARAMETERS is not set
+# CONFIG_FB_MBX is not set
+# CONFIG_FB_W100 is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_LCD_LTV350QV is not set
+# CONFIG_LCD_ILI9320 is not set
+CONFIG_LCD_TDO24M=y
+# CONFIG_LCD_VGG2432A4 is not set
+# CONFIG_LCD_PLATFORM is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_BACKLIGHT_DA903X=y
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+CONFIG_FONTS=y
+# CONFIG_FONT_8x8 is not set
+# CONFIG_FONT_8x16 is not set
+CONFIG_FONT_6x11=y
+# CONFIG_FONT_7x14 is not set
+# CONFIG_FONT_PEARL_8x8 is not set
+# CONFIG_FONT_ACORN_8x8 is not set
+# CONFIG_FONT_MINI_4x6 is not set
+# CONFIG_FONT_SUN8x16 is not set
+# CONFIG_FONT_SUN12x22 is not set
+# CONFIG_FONT_10x18 is not set
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+CONFIG_MMC_PXA=y
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_SPI is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=m
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=m
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP5521 is not set
+# CONFIG_LEDS_PCA955X is not set
+CONFIG_LEDS_DA903X=m
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_PWM is not set
+# CONFIG_LEDS_BD2802 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=m
+CONFIG_LEDS_TRIGGER_BACKLIGHT=m
+CONFIG_LEDS_TRIGGER_GPIO=m
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+CONFIG_RTC_LIB=y
+# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_DEBUG=y
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+CONFIG_REGULATOR_DA903X=y
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+CONFIG_FS_POSIX_ACL=y
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+# CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+# CONFIG_TMPFS is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_FS_WBUF_VERIFY=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RTIME=y
+CONFIG_JFFS2_RUBIN=y
+# CONFIG_JFFS2_CMODE_NONE is not set
+CONFIG_JFFS2_CMODE_PRIORITY=y
+# CONFIG_JFFS2_CMODE_SIZE is not set
+# CONFIG_JFFS2_CMODE_FAVOURLZO is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_ACL_SUPPORT=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_SHIRQ=y
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=1
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+CONFIG_DEBUG_PREEMPT=y
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+CONFIG_DEBUG_SPINLOCK=y
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+CONFIG_DEBUG_SPINLOCK_SLEEP=y
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_DEBUG_USER=y
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=y
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.31-rc6
+# Thu Aug 20 09:02:37 2009
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=".xcep-itech"
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EMBEDDED=y
+# CONFIG_UID16 is not set
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+# CONFIG_SHMEM is not set
+CONFIG_AIO=y
+
+#
+# Performance Counters
+#
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_STRIP_ASM_SYMS=y
+# CONFIG_COMPAT_BRK is not set
+# CONFIG_SLAB is not set
+# CONFIG_SLUB is not set
+CONFIG_SLOB=y
+# CONFIG_PROFILING is not set
+CONFIG_TRACEPOINTS=y
+CONFIG_MARKERS=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_KPROBES=y
+CONFIG_KRETPROBES=y
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLOCK is not set
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+
+#
+# Intel PXA2xx/PXA3xx Implementations
+#
+# CONFIG_ARCH_GUMSTIX is not set
+# CONFIG_MACH_INTELMOTE2 is not set
+# CONFIG_MACH_STARGATE2 is not set
+# CONFIG_ARCH_LUBBOCK is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_MACH_MP900C is not set
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_PXA_SHARPSL is not set
+# CONFIG_ARCH_VIPER is not set
+# CONFIG_ARCH_PXA_ESERIES is not set
+# CONFIG_TRIZEPS_PXA is not set
+# CONFIG_MACH_H5000 is not set
+# CONFIG_MACH_EM_X270 is not set
+# CONFIG_MACH_EXEDA is not set
+# CONFIG_MACH_COLIBRI is not set
+# CONFIG_MACH_COLIBRI300 is not set
+# CONFIG_MACH_COLIBRI320 is not set
+# CONFIG_MACH_ZYLONITE is not set
+# CONFIG_MACH_LITTLETON is not set
+# CONFIG_MACH_TAVOREVB is not set
+# CONFIG_MACH_SAAR is not set
+# CONFIG_MACH_ARMCORE is not set
+# CONFIG_MACH_CM_X300 is not set
+# CONFIG_MACH_H4700 is not set
+# CONFIG_MACH_MAGICIAN is not set
+# CONFIG_MACH_HIMALAYA is not set
+# CONFIG_MACH_MIOA701 is not set
+# CONFIG_MACH_PCM027 is not set
+# CONFIG_ARCH_PXA_PALM is not set
+# CONFIG_MACH_CSB726 is not set
+# CONFIG_PXA_EZX is not set
+CONFIG_MACH_XCEP=y
+CONFIG_PXA25x=y
+CONFIG_PXA_SSP=y
+CONFIG_PLAT_PXA=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_XSCALE=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+CONFIG_IWMMXT=y
+CONFIG_XSCALE_PMU=y
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT is not set
+CONFIG_HZ=100
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=mtd4 rootfstype=jffs2 ro console=ttyS0,115200"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=m
+CONFIG_PACKET_MMAP=y
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_NET_KEY=y
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_LRO=y
+# CONFIG_INET_DIAG is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_NET_TCPPROBE is not set
+# CONFIG_NET_DROP_MONITOR is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+# CONFIG_MTD_XIP is not set
+
+#
+# Mapping drivers for chip access
+#
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+# CONFIG_MTD_PHYSMAP_COMPAT is not set
+CONFIG_MTD_PXA2XX=y
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+
+#
+# SCSI device support
+#
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+CONFIG_SMC91X=y
+# CONFIG_DM9000 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+# CONFIG_DEVKMEM is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=m
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_PXA=m
+# CONFIG_I2C_PXA_SLAVE is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+# CONFIG_SPI is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=m
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7414 is not set
+# CONFIG_SENSORS_AD7418 is not set
+CONFIG_SENSORS_ADM1021=m
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7462 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ADT7475 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_G760A is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_LTC4215 is not set
+# CONFIG_SENSORS_LTC4245 is not set
+# CONFIG_SENSORS_LM95241 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+CONFIG_SENSORS_MAX6650=m
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_SHT15 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
+# CONFIG_NEW_LEDS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=m
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+CONFIG_RTC_DRV_SA1100=m
+# CONFIG_RTC_DRV_PXA is not set
+CONFIG_DMADEVICES=y
+
+#
+# DMA Devices
+#
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+CONFIG_FILE_LOCKING=y
+# CONFIG_FSNOTIFY is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_INOTIFY_USER is not set
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_FS_WBUF_VERIFY=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=m
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=m
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+CONFIG_NLS=m
+CONFIG_NLS_DEFAULT="utf8"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=m
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+CONFIG_FRAME_POINTER=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_KPROBES_SANITY_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_ARM_UNWIND is not set
+# CONFIG_DEBUG_USER is not set
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=m
+CONFIG_CRYPTO_ALGAPI2=m
+CONFIG_CRYPTO_HASH=m
+CONFIG_CRYPTO_HASH2=m
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23
-# Tue Oct 23 13:33:20 2007
-#
-CONFIG_ARM=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_TIME=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ZONE_DMA=y
-CONFIG_ARCH_MTD_XIP=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# General setup
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_LOG_BUF_SHIFT=18
-# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
-# CONFIG_RELAY is not set
-# CONFIG_BLK_DEV_INITRD is not set
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_SYSCTL=y
-# CONFIG_EMBEDDED is not set
-CONFIG_UID16=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
-CONFIG_EPOLL=y
-CONFIG_SIGNALFD=y
-CONFIG_EVENTFD=y
-CONFIG_SHMEM=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLUB_DEBUG=y
-# CONFIG_SLAB is not set
-CONFIG_SLUB=y
-# CONFIG_SLOB is not set
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-CONFIG_MODULES=y
-# CONFIG_MODULE_UNLOAD is not set
-# CONFIG_MODVERSIONS is not set
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-# CONFIG_BLK_DEV_BSG is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_DEFAULT_AS is not set
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-
-#
-# System Type
-#
-# CONFIG_ARCH_AAEC2000 is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_REALVIEW is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_NETX is not set
-# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP13XX is not set
-# CONFIG_ARCH_IOP32X is not set
-# CONFIG_ARCH_IOP33X is not set
-# CONFIG_ARCH_IXP23XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_L7200 is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
-# CONFIG_ARCH_MXC is not set
-# CONFIG_ARCH_PNX4008 is not set
-CONFIG_ARCH_PXA=y
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-# CONFIG_ARCH_DAVINCI is not set
-# CONFIG_ARCH_OMAP is not set
-
-#
-# Intel PXA2xx/PXA3xx Implementations
-#
-
-#
-# Supported PXA3xx Processor Variants
-#
-CONFIG_CPU_PXA300=y
-CONFIG_CPU_PXA310=y
-CONFIG_CPU_PXA320=y
-# CONFIG_ARCH_LUBBOCK is not set
-# CONFIG_MACH_LOGICPD_PXA270 is not set
-# CONFIG_MACH_MAINSTONE is not set
-# CONFIG_ARCH_PXA_IDP is not set
-# CONFIG_PXA_SHARPSL is not set
-# CONFIG_MACH_TRIZEPS4 is not set
-# CONFIG_MACH_EM_X270 is not set
-CONFIG_MACH_ZYLONITE=y
-# CONFIG_MACH_ARMCORE is not set
-CONFIG_PXA3xx=y
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
-
-#
-# Processor Type
-#
-CONFIG_CPU_32=y
-CONFIG_CPU_XSC3=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_IO_36=y
-
-#
-# Processor Features
-#
-# CONFIG_ARM_THUMB is not set
-# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
-CONFIG_IWMMXT=y
-
-#
-# Bus support
-#
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-# CONFIG_TICK_ONESHOT is not set
-# CONFIG_NO_HZ is not set
-# CONFIG_HIGH_RES_TIMERS is not set
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-# CONFIG_PREEMPT is not set
-CONFIG_HZ=100
-CONFIG_AEABI=y
-CONFIG_OABI_COMPAT=y
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
-CONFIG_VIRT_TO_BUS=y
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfs/rootfs/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS0,38400 mem=64M debug"
-# CONFIG_XIP_KERNEL is not set
-# CONFIG_KEXEC is not set
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-CONFIG_FPE_NWFPE=y
-# CONFIG_FPE_NWFPE_XP is not set
-# CONFIG_FPE_FASTFPE is not set
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_AOUT is not set
-# CONFIG_BINFMT_MISC is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-CONFIG_SUSPEND_UP_POSSIBLE=y
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
-# CONFIG_IP_DCCP is not set
-# CONFIG_IP_SCTP is not set
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
-# CONFIG_RFKILL is not set
-# CONFIG_NET_9P is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=y
-# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
-# CONFIG_PARPORT is not set
-# CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SCSI_NETLINK is not set
-# CONFIG_ATA is not set
-# CONFIG_MD is not set
-CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_MACVLAN is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-# CONFIG_VETH is not set
-# CONFIG_PHYLIB is not set
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_AX88796 is not set
-CONFIG_SMC91X=y
-# CONFIG_DM9000 is not set
-# CONFIG_SMC911X is not set
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_B44 is not set
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_ISDN is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-# CONFIG_INPUT_POLLDEV is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TABLET is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_PXA=y
-CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_IPMI_HANDLER is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-
-#
-# Sonics Silicon Backplane
-#
-CONFIG_SSB_POSSIBLE=y
-# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_SM501 is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_DAB is not set
-
-#
-# Graphics support
-#
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-CONFIG_FB=y
-# CONFIG_FIRMWARE_EDID is not set
-# CONFIG_FB_DDC is not set
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
-# CONFIG_FB_SYS_FILLRECT is not set
-# CONFIG_FB_SYS_COPYAREA is not set
-# CONFIG_FB_SYS_IMAGEBLIT is not set
-# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
-# CONFIG_FB_SVGALIB is not set
-# CONFIG_FB_MACMODES is not set
-# CONFIG_FB_BACKLIGHT is not set
-# CONFIG_FB_MODE_HELPERS is not set
-# CONFIG_FB_TILEBLITTING is not set
-
-#
-# Frame buffer hardware drivers
-#
-# CONFIG_FB_S1D13XXX is not set
-CONFIG_FB_PXA=y
-# CONFIG_FB_PXA_PARAMETERS is not set
-# CONFIG_FB_MBX is not set
-# CONFIG_FB_VIRTUAL is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FONTS=y
-# CONFIG_FONT_8x8 is not set
-# CONFIG_FONT_8x16 is not set
-CONFIG_FONT_6x11=y
-# CONFIG_FONT_7x14 is not set
-# CONFIG_FONT_PEARL_8x8 is not set
-# CONFIG_FONT_ACORN_8x8 is not set
-# CONFIG_FONT_MINI_4x6 is not set
-# CONFIG_FONT_SUN8x16 is not set
-# CONFIG_FONT_SUN12x22 is not set
-# CONFIG_FONT_10x18 is not set
-CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_MONO=y
-CONFIG_LOGO_LINUX_VGA16=y
-CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
-
-#
-# File systems
-#
-# CONFIG_EXT2_FS is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_INOTIFY is not set
-# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-CONFIG_NETWORK_FILESYSTEMS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_DIRECTIO=y
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_NFS_ACL_SUPPORT=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-CONFIG_SUNRPC_GSS=y
-# CONFIG_SUNRPC_BIND34 is not set
-CONFIG_RPCSEC_GSS_KRB5=y
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_NLS is not set
-# CONFIG_DLM is not set
-# CONFIG_INSTRUMENTATION is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_PRINTK_TIME is not set
-CONFIG_ENABLE_MUST_CHECK=y
-# CONFIG_MAGIC_SYSRQ is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-# CONFIG_DEBUG_KERNEL is not set
-# CONFIG_SLUB_DEBUG_ON is not set
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_FRAME_POINTER=y
-# CONFIG_SAMPLES is not set
-CONFIG_DEBUG_USER=y
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_MANAGER=y
-# CONFIG_CRYPTO_HMAC is not set
-# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
-# CONFIG_CRYPTO_SHA1 is not set
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
-# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_ECB is not set
-CONFIG_CRYPTO_CBC=y
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_AES is not set
-# CONFIG_CRYPTO_CAST5 is not set
-# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
-# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_SEED is not set
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
-# CONFIG_CRYPTO_HW is not set
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-# CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
-CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y
#ifdef __KERNEL__
+/*
+ * On ARM, ordinary assignment (str instruction) doesn't clear the local
+ * strex/ldrex monitor on some implementations. The reason we can use it for
+ * atomic_set() is the clrex or dummy strex done on every exception return.
+ */
#define atomic_read(v) ((v)->counter)
+#define atomic_set(v,i) (((v)->counter) = (i))
#if __LINUX_ARM_ARCH__ >= 6
/*
* ARMv6 UP and SMP safe atomic ops. We use load exclusive and
* store exclusive to ensure that these are atomic. We may loop
- * to ensure that the update happens. Writing to 'v->counter'
- * without using the following operations WILL break the atomic
- * nature of these ops.
+ * to ensure that the update happens.
*/
-static inline void atomic_set(atomic_t *v, int i)
-{
- unsigned long tmp;
-
- __asm__ __volatile__("@ atomic_set\n"
-"1: ldrex %0, [%1]\n"
-" strex %0, %2, [%1]\n"
-" teq %0, #0\n"
-" bne 1b"
- : "=&r" (tmp)
- : "r" (&v->counter), "r" (i)
- : "cc");
-}
-
static inline void atomic_add(int i, atomic_t *v)
{
unsigned long tmp;
#error SMP not supported on pre-ARMv6 CPUs
#endif
-#define atomic_set(v,i) (((v)->counter) = (i))
-
static inline int atomic_add_return(int i, atomic_t *v)
{
unsigned long flags;
#ifndef __ASMARM_CACHE_H
#define __ASMARM_CACHE_H
-#define L1_CACHE_SHIFT 5
+#define L1_CACHE_SHIFT CONFIG_ARM_L1_CACHE_SHIFT
#define L1_CACHE_BYTES (1 << L1_CACHE_SHIFT)
/*
return read_cpuid(CPUID_CACHETYPE);
}
+static inline unsigned int __attribute_const__ read_cpuid_tcmstatus(void)
+{
+ return read_cpuid(CPUID_TCM);
+}
+
/*
* Intel's XScale3 core supports some v6 features (supersections, L2)
* but advertises itself as v5 as it does not support the v6 ISA. For
#else
static inline int cpu_is_xsc3(void)
{
- if ((read_cpuid_id() & 0xffffe000) == 0x69056000)
+ unsigned int id;
+ id = read_cpuid_id() & 0xffffe000;
+ /* It covers both Intel ID and Marvell ID */
+ if ((id == 0x69056000) || (id == 0x56056000))
return 1;
return 0;
--- /dev/null
+/*
+ *
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ *
+ */
+#ifndef __ASMARM_TCM_H
+#define __ASMARM_TCM_H
+
+#ifndef CONFIG_HAVE_TCM
+#error "You should not be including tcm.h unless you have a TCM!"
+#endif
+
+#include <linux/compiler.h>
+
+/* Tag variables with this */
+#define __tcmdata __section(.tcm.data)
+/* Tag constants with this */
+#define __tcmconst __section(.tcm.rodata)
+/* Tag functions inside TCM called from outside TCM with this */
+#define __tcmfunc __attribute__((long_call)) __section(.tcm.text) noinline
+/* Tag function inside TCM called from inside TCM with this */
+#define __tcmlocalfunc __section(.tcm.text)
+
+void *tcm_alloc(size_t len);
+void tcm_free(void *addr, size_t len);
+
+#endif
#define ARM(x...)
#define THUMB(x...) x
+#ifdef __ASSEMBLY__
#define W(instr) instr.w
+#endif
#define BSYM(sym) sym + 1
#else /* !CONFIG_THUMB2_KERNEL */
#define ARM(x...) x
#define THUMB(x...)
+#ifdef __ASSEMBLY__
#define W(instr) instr
+#endif
#define BSYM(sym) sym
#endif /* CONFIG_THUMB2_KERNEL */
obj-$(CONFIG_ARM_THUMBEE) += thumbee.o
obj-$(CONFIG_KGDB) += kgdb.o
obj-$(CONFIG_ARM_UNWIND) += unwind.o
+obj-$(CONFIG_HAVE_TCM) += tcm.o
obj-$(CONFIG_CRUNCH) += crunch.o crunch-bits.o
AFLAGS_crunch-bits.o := -Wa,-mcpu=ep9312
@
@ r0 - instruction
@
+#ifndef CONFIG_THUMB2_KERNEL
ldr r0, [r2, #-4]
+#else
+ ldrh r0, [r2, #-2] @ Thumb instruction at LR - 2
+ and r9, r0, #0xf800
+ cmp r9, #0xe800 @ 32-bit instruction if xx >= 0
+ ldrhhs r9, [r2] @ bottom 16 bits
+ orrhs r0, r9, r0, lsl #16
+#endif
adr r9, BSYM(1f)
bl call_fpe
.word no_fp
.previous
-no_fp: mov pc, lr
+ENTRY(no_fp)
+ mov pc, lr
+ENDPROC(no_fp)
__und_usr_unknown:
enable_irq
#ifdef CONFIG_MMU
ldr r6, [r2, #TI_CPU_DOMAIN]
#endif
-#if __LINUX_ARM_ARCH__ >= 6
-#ifdef CONFIG_CPU_32v6K
- clrex
-#else
- strex r5, r4, [ip] @ Clear exclusive monitor
-#endif
-#endif
#if defined(CONFIG_HAS_TLS_REG)
mcr p15, 0, r3, c13, c0, 3 @ set TLS register
#elif !defined(CONFIG_TLS_REG_EMUL)
#ifndef CONFIG_THUMB2_KERNEL
.macro svc_exit, rpsr
msr spsr_cxsf, \rpsr
+#if defined(CONFIG_CPU_32v6K)
+ clrex @ clear the exclusive monitor
ldmia sp, {r0 - pc}^ @ load r0 - pc, cpsr
+#elif defined (CONFIG_CPU_V6)
+ ldr r0, [sp]
+ strex r1, r2, [sp] @ clear the exclusive monitor
+ ldmib sp, {r1 - pc}^ @ load r1 - pc, cpsr
+#else
+ ldmia sp, {r0 - pc}^ @ load r0 - pc, cpsr
+#endif
.endm
.macro restore_user_regs, fast = 0, offset = 0
ldr r1, [sp, #\offset + S_PSR] @ get calling cpsr
ldr lr, [sp, #\offset + S_PC]! @ get pc
msr spsr_cxsf, r1 @ save in spsr_svc
+#if defined(CONFIG_CPU_32v6K)
+ clrex @ clear the exclusive monitor
+#elif defined (CONFIG_CPU_V6)
+ strex r1, r2, [sp] @ clear the exclusive monitor
+#endif
.if \fast
ldmdb sp, {r1 - lr}^ @ get calling r1 - lr
.else
.endm
#else /* CONFIG_THUMB2_KERNEL */
.macro svc_exit, rpsr
+ clrex @ clear the exclusive monitor
ldr r0, [sp, #S_SP] @ top of the stack
ldr r1, [sp, #S_PC] @ return address
tst r0, #4 @ orig stack 8-byte aligned?
.endm
.macro restore_user_regs, fast = 0, offset = 0
+ clrex @ clear the exclusive monitor
mov r2, sp
load_user_sp_lr r2, r3, \offset + S_SP @ calling sp, lr
ldr r1, [sp, #\offset + S_PSR] @ get calling cpsr
#include <linux/kernel.h>
#include <linux/kprobes.h>
#include <linux/module.h>
+#include <linux/stop_machine.h>
#include <linux/stringify.h>
#include <asm/traps.h>
#include <asm/cacheflush.h>
flush_insns(p->addr, 1);
}
+/*
+ * The actual disarming is done here on each CPU and synchronized using
+ * stop_machine. This synchronization is necessary on SMP to avoid removing
+ * a probe between the moment the 'Undefined Instruction' exception is raised
+ * and the moment the exception handler reads the faulting instruction from
+ * memory.
+ */
+int __kprobes __arch_disarm_kprobe(void *p)
+{
+ struct kprobe *kp = p;
+ *kp->addr = kp->opcode;
+ flush_insns(kp->addr, 1);
+ return 0;
+}
+
void __kprobes arch_disarm_kprobe(struct kprobe *p)
{
- *p->addr = p->opcode;
- flush_insns(p->addr, 1);
+ stop_machine(__arch_disarm_kprobe, p, &cpu_online_map);
}
void __kprobes arch_remove_kprobe(struct kprobe *p)
#include "compat.h"
#include "atags.h"
+#include "tcm.h"
#ifndef MEM_SIZE
#define MEM_SIZE (16*1024*1024)
#endif
cpu_init();
+ tcm_init();
/*
* Set up various architecture-specific pointers
--- /dev/null
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * TCM memory handling for ARM systems
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/stddef.h>
+#include <linux/ioport.h>
+#include <linux/genalloc.h>
+#include <linux/string.h> /* memcpy */
+#include <asm/page.h> /* PAGE_SHIFT */
+#include <asm/cputype.h>
+#include <asm/mach/map.h>
+#include <mach/memory.h>
+#include "tcm.h"
+
+/* Scream and warn about misuse */
+#if !defined(ITCM_OFFSET) || !defined(ITCM_END) || \
+ !defined(DTCM_OFFSET) || !defined(DTCM_END)
+#error "TCM support selected but offsets not defined!"
+#endif
+
+static struct gen_pool *tcm_pool;
+
+/* TCM section definitions from the linker */
+extern char __itcm_start, __sitcm_text, __eitcm_text;
+extern char __dtcm_start, __sdtcm_data, __edtcm_data;
+
+/*
+ * TCM memory resources
+ */
+static struct resource dtcm_res = {
+ .name = "DTCM RAM",
+ .start = DTCM_OFFSET,
+ .end = DTCM_END,
+ .flags = IORESOURCE_MEM
+};
+
+static struct resource itcm_res = {
+ .name = "ITCM RAM",
+ .start = ITCM_OFFSET,
+ .end = ITCM_END,
+ .flags = IORESOURCE_MEM
+};
+
+static struct map_desc dtcm_iomap[] __initdata = {
+ {
+ .virtual = DTCM_OFFSET,
+ .pfn = __phys_to_pfn(DTCM_OFFSET),
+ .length = (DTCM_END - DTCM_OFFSET + 1),
+ .type = MT_UNCACHED
+ }
+};
+
+static struct map_desc itcm_iomap[] __initdata = {
+ {
+ .virtual = ITCM_OFFSET,
+ .pfn = __phys_to_pfn(ITCM_OFFSET),
+ .length = (ITCM_END - ITCM_OFFSET + 1),
+ .type = MT_UNCACHED
+ }
+};
+
+/*
+ * Allocate a chunk of TCM memory
+ */
+void *tcm_alloc(size_t len)
+{
+ unsigned long vaddr;
+
+ if (!tcm_pool)
+ return NULL;
+
+ vaddr = gen_pool_alloc(tcm_pool, len);
+ if (!vaddr)
+ return NULL;
+
+ return (void *) vaddr;
+}
+EXPORT_SYMBOL(tcm_alloc);
+
+/*
+ * Free a chunk of TCM memory
+ */
+void tcm_free(void *addr, size_t len)
+{
+ gen_pool_free(tcm_pool, (unsigned long) addr, len);
+}
+EXPORT_SYMBOL(tcm_free);
+
+
+static void __init setup_tcm_bank(u8 type, u32 offset, u32 expected_size)
+{
+ const int tcm_sizes[16] = { 0, -1, -1, 4, 8, 16, 32, 64, 128,
+ 256, 512, 1024, -1, -1, -1, -1 };
+ u32 tcm_region;
+ int tcm_size;
+
+ /* Read the special TCM region register c9, 0 */
+ if (!type)
+ asm("mrc p15, 0, %0, c9, c1, 0"
+ : "=r" (tcm_region));
+ else
+ asm("mrc p15, 0, %0, c9, c1, 1"
+ : "=r" (tcm_region));
+
+ tcm_size = tcm_sizes[(tcm_region >> 2) & 0x0f];
+ if (tcm_size < 0) {
+ pr_err("CPU: %sTCM of unknown size!\n",
+ type ? "I" : "D");
+ } else {
+ pr_info("CPU: found %sTCM %dk @ %08x, %senabled\n",
+ type ? "I" : "D",
+ tcm_size,
+ (tcm_region & 0xfffff000U),
+ (tcm_region & 1) ? "" : "not ");
+ }
+
+ if (tcm_size != expected_size) {
+ pr_crit("CPU: %sTCM was detected %dk but expected %dk!\n",
+ type ? "I" : "D",
+ tcm_size,
+ expected_size);
+ /* Adjust to the expected size? what can we do... */
+ }
+
+ /* Force move the TCM bank to where we want it, enable */
+ tcm_region = offset | (tcm_region & 0x00000ffeU) | 1;
+
+ if (!type)
+ asm("mcr p15, 0, %0, c9, c1, 0"
+ : /* No output operands */
+ : "r" (tcm_region));
+ else
+ asm("mcr p15, 0, %0, c9, c1, 1"
+ : /* No output operands */
+ : "r" (tcm_region));
+
+ pr_debug("CPU: moved %sTCM %dk to %08x, enabled\n",
+ type ? "I" : "D",
+ tcm_size,
+ (tcm_region & 0xfffff000U));
+}
+
+/*
+ * This initializes the TCM memory
+ */
+void __init tcm_init(void)
+{
+ u32 tcm_status = read_cpuid_tcmstatus();
+ char *start;
+ char *end;
+ char *ram;
+
+ /* Setup DTCM if present */
+ if (tcm_status & (1 << 16)) {
+ setup_tcm_bank(0, DTCM_OFFSET,
+ (DTCM_END - DTCM_OFFSET + 1) >> 10);
+ request_resource(&iomem_resource, &dtcm_res);
+ iotable_init(dtcm_iomap, 1);
+ /* Copy data from RAM to DTCM */
+ start = &__sdtcm_data;
+ end = &__edtcm_data;
+ ram = &__dtcm_start;
+ memcpy(start, ram, (end-start));
+ pr_debug("CPU DTCM: copied data from %p - %p\n", start, end);
+ }
+
+ /* Setup ITCM if present */
+ if (tcm_status & 1) {
+ setup_tcm_bank(1, ITCM_OFFSET,
+ (ITCM_END - ITCM_OFFSET + 1) >> 10);
+ request_resource(&iomem_resource, &itcm_res);
+ iotable_init(itcm_iomap, 1);
+ /* Copy code from RAM to ITCM */
+ start = &__sitcm_text;
+ end = &__eitcm_text;
+ ram = &__itcm_start;
+ memcpy(start, ram, (end-start));
+ pr_debug("CPU ITCM: copied code from %p - %p\n", start, end);
+ }
+}
+
+/*
+ * This creates the TCM memory pool and has to be done later,
+ * during the core_initicalls, since the allocator is not yet
+ * up and running when the first initialization runs.
+ */
+static int __init setup_tcm_pool(void)
+{
+ u32 tcm_status = read_cpuid_tcmstatus();
+ u32 dtcm_pool_start = (u32) &__edtcm_data;
+ u32 itcm_pool_start = (u32) &__eitcm_text;
+ int ret;
+
+ /*
+ * Set up malloc pool, 2^2 = 4 bytes granularity since
+ * the TCM is sometimes just 4 KiB. NB: pages and cache
+ * line alignments does not matter in TCM!
+ */
+ tcm_pool = gen_pool_create(2, -1);
+
+ pr_debug("Setting up TCM memory pool\n");
+
+ /* Add the rest of DTCM to the TCM pool */
+ if (tcm_status & (1 << 16)) {
+ if (dtcm_pool_start < DTCM_END) {
+ ret = gen_pool_add(tcm_pool, dtcm_pool_start,
+ DTCM_END - dtcm_pool_start + 1, -1);
+ if (ret) {
+ pr_err("CPU DTCM: could not add DTCM " \
+ "remainder to pool!\n");
+ return ret;
+ }
+ pr_debug("CPU DTCM: Added %08x bytes @ %08x to " \
+ "the TCM memory pool\n",
+ DTCM_END - dtcm_pool_start + 1,
+ dtcm_pool_start);
+ }
+ }
+
+ /* Add the rest of ITCM to the TCM pool */
+ if (tcm_status & 1) {
+ if (itcm_pool_start < ITCM_END) {
+ ret = gen_pool_add(tcm_pool, itcm_pool_start,
+ ITCM_END - itcm_pool_start + 1, -1);
+ if (ret) {
+ pr_err("CPU ITCM: could not add ITCM " \
+ "remainder to pool!\n");
+ return ret;
+ }
+ pr_debug("CPU ITCM: Added %08x bytes @ %08x to " \
+ "the TCM memory pool\n",
+ ITCM_END - itcm_pool_start + 1,
+ itcm_pool_start);
+ }
+ }
+ return 0;
+}
+
+core_initcall(setup_tcm_pool);
--- /dev/null
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * TCM memory handling for ARM systems
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ */
+
+#ifdef CONFIG_HAVE_TCM
+void __init tcm_init(void);
+#else
+/* No TCM support, just blank inlines to be optimized out */
+inline void tcm_init(void)
+{
+}
+#endif
}
_edata_loc = __data_loc + SIZEOF(.data);
+#ifdef CONFIG_HAVE_TCM
+ /*
+ * We align everything to a page boundary so we can
+ * free it after init has commenced and TCM contents have
+ * been copied to its destination.
+ */
+ .tcm_start : {
+ . = ALIGN(PAGE_SIZE);
+ __tcm_start = .;
+ __itcm_start = .;
+ }
+
+ /*
+ * Link these to the ITCM RAM
+ * Put VMA to the TCM address and LMA to the common RAM
+ * and we'll upload the contents from RAM to TCM and free
+ * the used RAM after that.
+ */
+ .text_itcm ITCM_OFFSET : AT(__itcm_start)
+ {
+ __sitcm_text = .;
+ *(.tcm.text)
+ *(.tcm.rodata)
+ . = ALIGN(4);
+ __eitcm_text = .;
+ }
+
+ /*
+ * Reset the dot pointer, this is needed to create the
+ * relative __dtcm_start below (to be used as extern in code).
+ */
+ . = ADDR(.tcm_start) + SIZEOF(.tcm_start) + SIZEOF(.text_itcm);
+
+ .dtcm_start : {
+ __dtcm_start = .;
+ }
+
+ /* TODO: add remainder of ITCM as well, that can be used for data! */
+ .data_dtcm DTCM_OFFSET : AT(__dtcm_start)
+ {
+ . = ALIGN(4);
+ __sdtcm_data = .;
+ *(.tcm.data)
+ . = ALIGN(4);
+ __edtcm_data = .;
+ }
+
+ /* Reset the dot pointer or the linker gets confused */
+ . = ADDR(.dtcm_start) + SIZEOF(.data_dtcm);
+
+ /* End marker for freeing TCM copy in linked object */
+ .tcm_end : AT(ADDR(.dtcm_start) + SIZEOF(.data_dtcm)){
+ . = ALIGN(PAGE_SIZE);
+ __tcm_end = .;
+ }
+#endif
+
.bss : {
__bss_start = .; /* BSS */
*(.bss)
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <asm/asm-offsets.h>
+#include <asm/cache.h>
-#define COPY_COUNT (PAGE_SZ/64 PLD( -1 ))
+#define COPY_COUNT (PAGE_SZ / (2 * L1_CACHE_BYTES) PLD( -1 ))
.text
.align 5
ENTRY(copy_page)
stmfd sp!, {r4, lr} @ 2
PLD( pld [r1, #0] )
- PLD( pld [r1, #32] )
+ PLD( pld [r1, #L1_CACHE_BYTES] )
mov r2, #COPY_COUNT @ 1
ldmia r1!, {r3, r4, ip, lr} @ 4+1
-1: PLD( pld [r1, #64] )
- PLD( pld [r1, #96] )
-2: stmia r0!, {r3, r4, ip, lr} @ 4
- ldmia r1!, {r3, r4, ip, lr} @ 4+1
- stmia r0!, {r3, r4, ip, lr} @ 4
- ldmia r1!, {r3, r4, ip, lr} @ 4+1
+1: PLD( pld [r1, #2 * L1_CACHE_BYTES])
+ PLD( pld [r1, #3 * L1_CACHE_BYTES])
+2:
+ .rept (2 * L1_CACHE_BYTES / 16 - 1)
stmia r0!, {r3, r4, ip, lr} @ 4
ldmia r1!, {r3, r4, ip, lr} @ 4
+ .endr
subs r2, r2, #1 @ 1
stmia r0!, {r3, r4, ip, lr} @ 4
ldmgtia r1!, {r3, r4, ip, lr} @ 4
* AC97
* -------------------------------------------------------------------- */
-#if defined(CONFIG_SND_AT91_AC97) || defined(CONFIG_SND_AT91_AC97_MODULE)
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
static u64 ac97_dmamask = DMA_BIT_MASK(32);
-static struct atmel_ac97_data ac97_data;
+static struct ac97c_platform_data ac97_data;
static struct resource ac97_resources[] = {
[0] = {
};
static struct platform_device at91cap9_ac97_device = {
- .name = "ac97c",
+ .name = "atmel_ac97c",
.id = 1,
.dev = {
.dma_mask = &ac97_dmamask,
.num_resources = ARRAY_SIZE(ac97_resources),
};
-void __init at91_add_device_ac97(struct atmel_ac97_data *data)
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
{
if (!data)
return;
platform_device_register(&at91cap9_ac97_device);
}
#else
-void __init at91_add_device_ac97(struct atmel_ac97_data *data) {}
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
#endif
void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
#endif
+/* --------------------------------------------------------------------
+ * CAN Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_CAN_AT91) || defined(CONFIG_CAN_AT91_MODULE)
+static struct resource can_resources[] = {
+ [0] = {
+ .start = AT91SAM9263_BASE_CAN,
+ .end = AT91SAM9263_BASE_CAN + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9263_ID_CAN,
+ .end = AT91SAM9263_ID_CAN,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9263_can_device = {
+ .name = "at91_can",
+ .id = -1,
+ .resource = can_resources,
+ .num_resources = ARRAY_SIZE(can_resources),
+};
+
+void __init at91_add_device_can(struct at91_can_data *data)
+{
+ at91_set_A_periph(AT91_PIN_PA13, 0); /* CANTX */
+ at91_set_A_periph(AT91_PIN_PA14, 0); /* CANRX */
+ at91sam9263_can_device.dev.platform_data = data;
+
+ platform_device_register(&at91sam9263_can_device);
+}
+#else
+void __init at91_add_device_can(struct at91_can_data *data) {}
+#endif
/* --------------------------------------------------------------------
* LCD Controller
#include <mach/at91sam9g45.h>
#include <mach/at91sam9g45_matrix.h>
#include <mach/at91sam9_smc.h>
+#include <mach/at_hdmac.h>
#include "generic.h"
+/* --------------------------------------------------------------------
+ * HDMAC - AHB DMA Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
+static u64 hdmac_dmamask = DMA_BIT_MASK(32);
+
+static struct at_dma_platform_data atdma_pdata = {
+ .nr_channels = 8,
+};
+
+static struct resource hdmac_resources[] = {
+ [0] = {
+ .start = AT91_BASE_SYS + AT91_DMA,
+ .end = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = AT91SAM9G45_ID_DMA,
+ .end = AT91SAM9G45_ID_DMA,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at_hdmac_device = {
+ .name = "at_hdmac",
+ .id = -1,
+ .dev = {
+ .dma_mask = &hdmac_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &atdma_pdata,
+ },
+ .resource = hdmac_resources,
+ .num_resources = ARRAY_SIZE(hdmac_resources),
+};
+
+void __init at91_add_device_hdmac(void)
+{
+ dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
+ dma_cap_set(DMA_SLAVE, atdma_pdata.cap_mask);
+ platform_device_register(&at_hdmac_device);
+}
+#else
+void __init at91_add_device_hdmac(void) {}
+#endif
+
+
/* --------------------------------------------------------------------
* USB Host (OHCI)
* -------------------------------------------------------------------- */
#endif
+/* --------------------------------------------------------------------
+ * AC97
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
+static u64 ac97_dmamask = DMA_BIT_MASK(32);
+static struct ac97c_platform_data ac97_data;
+
+static struct resource ac97_resources[] = {
+ [0] = {
+ .start = AT91SAM9G45_BASE_AC97C,
+ .end = AT91SAM9G45_BASE_AC97C + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9G45_ID_AC97C,
+ .end = AT91SAM9G45_ID_AC97C,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9g45_ac97_device = {
+ .name = "atmel_ac97c",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ac97_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &ac97_data,
+ },
+ .resource = ac97_resources,
+ .num_resources = ARRAY_SIZE(ac97_resources),
+};
+
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
+{
+ if (!data)
+ return;
+
+ at91_set_A_periph(AT91_PIN_PD8, 0); /* AC97FS */
+ at91_set_A_periph(AT91_PIN_PD9, 0); /* AC97CK */
+ at91_set_A_periph(AT91_PIN_PD7, 0); /* AC97TX */
+ at91_set_A_periph(AT91_PIN_PD6, 0); /* AC97RX */
+
+ /* reset */
+ if (data->reset_pin)
+ at91_set_gpio_output(data->reset_pin, 0);
+
+ ac97_data = *data;
+ platform_device_register(&at91sam9g45_ac97_device);
+}
+#else
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
+#endif
+
+
/* --------------------------------------------------------------------
* LCD Controller
* -------------------------------------------------------------------- */
*/
static int __init at91_add_standard_devices(void)
{
+ at91_add_device_hdmac();
at91_add_device_rtc();
at91_add_device_rtt();
at91_add_device_watchdog();
#include <mach/at91sam9rl.h>
#include <mach/at91sam9rl_matrix.h>
#include <mach/at91sam9_smc.h>
+#include <mach/at_hdmac.h>
#include "generic.h"
+/* --------------------------------------------------------------------
+ * HDMAC - AHB DMA Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
+static u64 hdmac_dmamask = DMA_BIT_MASK(32);
+
+static struct at_dma_platform_data atdma_pdata = {
+ .nr_channels = 2,
+};
+
+static struct resource hdmac_resources[] = {
+ [0] = {
+ .start = AT91_BASE_SYS + AT91_DMA,
+ .end = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = AT91SAM9RL_ID_DMA,
+ .end = AT91SAM9RL_ID_DMA,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at_hdmac_device = {
+ .name = "at_hdmac",
+ .id = -1,
+ .dev = {
+ .dma_mask = &hdmac_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &atdma_pdata,
+ },
+ .resource = hdmac_resources,
+ .num_resources = ARRAY_SIZE(hdmac_resources),
+};
+
+void __init at91_add_device_hdmac(void)
+{
+ dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
+ platform_device_register(&at_hdmac_device);
+}
+#else
+void __init at91_add_device_hdmac(void) {}
+#endif
+
/* --------------------------------------------------------------------
* USB HS Device (Gadget)
* -------------------------------------------------------------------- */
#endif
+/* --------------------------------------------------------------------
+ * AC97
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
+static u64 ac97_dmamask = DMA_BIT_MASK(32);
+static struct ac97c_platform_data ac97_data;
+
+static struct resource ac97_resources[] = {
+ [0] = {
+ .start = AT91SAM9RL_BASE_AC97C,
+ .end = AT91SAM9RL_BASE_AC97C + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9RL_ID_AC97C,
+ .end = AT91SAM9RL_ID_AC97C,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9rl_ac97_device = {
+ .name = "atmel_ac97c",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ac97_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &ac97_data,
+ },
+ .resource = ac97_resources,
+ .num_resources = ARRAY_SIZE(ac97_resources),
+};
+
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
+{
+ if (!data)
+ return;
+
+ at91_set_A_periph(AT91_PIN_PD1, 0); /* AC97FS */
+ at91_set_A_periph(AT91_PIN_PD2, 0); /* AC97CK */
+ at91_set_A_periph(AT91_PIN_PD3, 0); /* AC97TX */
+ at91_set_A_periph(AT91_PIN_PD4, 0); /* AC97RX */
+
+ /* reset */
+ if (data->reset_pin)
+ at91_set_gpio_output(data->reset_pin, 0);
+
+ ac97_data = *data;
+ platform_device_register(&at91sam9rl_ac97_device);
+}
+#else
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
+#endif
+
+
/* --------------------------------------------------------------------
* LCD Controller
* -------------------------------------------------------------------- */
*/
static int __init at91_add_standard_devices(void)
{
+ at91_add_device_hdmac();
at91_add_device_rtc();
at91_add_device_rtt();
at91_add_device_watchdog();
/*
* AC97
*/
-static struct atmel_ac97_data cap9adk_ac97_data = {
+static struct ac97c_platform_data cap9adk_ac97_data = {
// .reset_pin = ... not connected
};
/*
* AC97
*/
-static struct atmel_ac97_data neocore926_ac97_data = {
+static struct ac97c_platform_data neocore926_ac97_data = {
.reset_pin = AT91_PIN_PA13,
};
}
};
+/*
+ * CAN
+ */
+static void sam9263ek_transceiver_switch(int on)
+{
+ if (on) {
+ at91_set_gpio_output(AT91_PIN_PA18, 1); /* CANRXEN */
+ at91_set_gpio_output(AT91_PIN_PA19, 0); /* CANRS */
+ } else {
+ at91_set_gpio_output(AT91_PIN_PA18, 0); /* CANRXEN */
+ at91_set_gpio_output(AT91_PIN_PA19, 1); /* CANRS */
+ }
+}
+
+static struct at91_can_data ek_can_data = {
+ .transceiver_switch = sam9263ek_transceiver_switch,
+};
static void __init ek_board_init(void)
{
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
+ /* CAN */
+ at91_add_device_can(&ek_can_data);
}
MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
#endif
+/*
+ * AC97
+ * reset_pin is not connected: NRST
+ */
+static struct ac97c_platform_data ek_ac97_data = {
+};
+
+
/*
* LEDs ... these could all be PWM-driven, for variable brightness
*/
at91_add_device_lcdc(&ek_lcdc_data);
/* Push Buttons */
ek_add_device_buttons();
+ /* AC97 */
+ at91_add_device_ac97(&ek_ac97_data);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
#endif
+/*
+ * AC97
+ * reset_pin is not connected: NRST
+ */
+static struct ac97c_platform_data ek_ac97_data = {
+};
+
+
/*
* LEDs
*/
at91_add_device_mmc(0, &ek_mmc_data);
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
+ /* AC97 */
+ at91_add_device_ac97(&ek_ac97_data);
/* Touch Screen Controller */
at91_add_device_tsadcc();
/* LEDs */
/* Touchscreen Controller */
extern void __init at91_add_device_tsadcc(void);
+/* CAN */
+struct at91_can_data {
+ void (*transceiver_switch)(int on);
+};
+extern void __init at91_add_device_can(struct at91_can_data *data);
+
/* LEDs */
extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
extern void __init at91_gpio_leds(struct gpio_led *leds, int nr);
#include <linux/amba/bus.h>
#include <linux/amba/kmi.h>
#include <linux/amba/clcd.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <asm/clkdev.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/irq.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
return status & 8;
}
-static struct mmc_platform_data mmc_data = {
+static struct mmci_platform_data mmc_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = mmc_status,
.gpio_wp = -1,
config CPU_PXA935
bool "PXA935 (codename Tavor-P65)"
+ select CPU_PXA930
+
+config CPU_PXA950
+ bool "PXA950 (codename Tavor-PV2)"
+ select CPU_PXA930
endmenu
bool "Nec Mobilepro 900/c"
select PXA25x
+config MACH_BALLOON3
+ bool "Balloon 3 board"
+ select PXA27x
+ select IWMMXT
+ select PXA_HAVE_BOARD_IRQS
+
config ARCH_PXA_IDP
bool "Accelent Xscale IDP"
select PXA25x
Say Y here if you intend to run this kernel on a Palm Tungsten|E2
handheld computer.
+config MACH_PALMTC
+ bool "Palm Tungsten|C"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA25x
+ help
+ Say Y here if you intend to run this kernel on a Palm Tungsten|C
+ handheld computer.
+
config MACH_PALMT5
bool "Palm Tungsten|T5"
default y
select PXA27x
select IWMMXT
select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
config MACH_EZX_A780
bool "Motorola EZX A780"
default y
depends on PXA_EZX
+config MACH_XCEP
+ bool "Iskratel Electronics XCEP"
+ select PXA25x
+ select MTD
+ select MTD_PARTITIONS
+ select MTD_PHYSMAP
+ select MTD_CFI_INTELEXT
+ select MTD_CFI
+ select MTD_CHAR
+ select SMC91X
+ select PXA_SSP
+ help
+ PXA255 based Single Board Computer with SMC 91C111 ethernet chip and 64 MB of flash.
+ Tuned for usage in Libera instruments for particle accelerators.
+
endmenu
config PXA25x
obj-$(CONFIG_ARCH_LUBBOCK) += lubbock.o
obj-$(CONFIG_MACH_LOGICPD_PXA270) += lpd270.o
obj-$(CONFIG_MACH_MAINSTONE) += mainstone.o
+obj-$(CONFIG_MACH_BALLOON3) += balloon3.o
obj-$(CONFIG_MACH_MP900C) += mp900.o
obj-$(CONFIG_ARCH_PXA_IDP) += idp.o
obj-$(CONFIG_MACH_TRIZEPS4) += trizeps4.o
obj-$(CONFIG_MACH_E400) += e400.o
obj-$(CONFIG_MACH_E800) += e800.o
obj-$(CONFIG_MACH_PALMTE2) += palmte2.o
+obj-$(CONFIG_MACH_PALMTC) += palmtc.o
obj-$(CONFIG_MACH_PALMT5) += palmt5.o
obj-$(CONFIG_MACH_PALMTX) += palmtx.o
obj-$(CONFIG_MACH_PALMLD) += palmld.o
obj-$(CONFIG_MACH_CM_X300) += cm-x300.o
obj-$(CONFIG_PXA_EZX) += ezx.o
+obj-$(CONFIG_MACH_XCEP) += xcep.o
+
obj-$(CONFIG_MACH_INTELMOTE2) += imote2.o
obj-$(CONFIG_MACH_STARGATE2) += stargate2.o
obj-$(CONFIG_MACH_CSB726) += csb726.o
--- /dev/null
+/*
+ * linux/arch/arm/mach-pxa/balloon3.c
+ *
+ * Support for Balloonboard.org Balloon3 board.
+ *
+ * Author: Nick Bane, Wookey, Jonathan McDowell
+ * Created: June, 2006
+ * Copyright: Toby Churchill Ltd
+ * Derived from mainstone.c, by Nico Pitre
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/bitops.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/ioport.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/types.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+#include <asm/sizes.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/flash.h>
+
+#include <mach/pxa27x.h>
+#include <mach/balloon3.h>
+#include <mach/audio.h>
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
+#include <mach/udc.h>
+#include <mach/pxa27x-udc.h>
+#include <mach/irda.h>
+#include <mach/ohci.h>
+
+#include <plat/i2c.h>
+
+#include "generic.h"
+#include "devices.h"
+
+static unsigned long balloon3_irq_enabled;
+
+static unsigned long balloon3_features_present =
+ (1 << BALLOON3_FEATURE_OHCI) | (1 << BALLOON3_FEATURE_CF) |
+ (1 << BALLOON3_FEATURE_AUDIO) |
+ (1 << BALLOON3_FEATURE_TOPPOLY);
+
+int balloon3_has(enum balloon3_features feature)
+{
+ return (balloon3_features_present & (1 << feature)) ? 1 : 0;
+}
+EXPORT_SYMBOL_GPL(balloon3_has);
+
+int __init parse_balloon3_features(char *arg)
+{
+ if (!arg)
+ return 0;
+
+ return strict_strtoul(arg, 0, &balloon3_features_present);
+}
+early_param("balloon3_features", parse_balloon3_features);
+
+static void balloon3_mask_irq(unsigned int irq)
+{
+ int balloon3_irq = (irq - BALLOON3_IRQ(0));
+ balloon3_irq_enabled &= ~(1 << balloon3_irq);
+ __raw_writel(~balloon3_irq_enabled, BALLOON3_INT_CONTROL_REG);
+}
+
+static void balloon3_unmask_irq(unsigned int irq)
+{
+ int balloon3_irq = (irq - BALLOON3_IRQ(0));
+ balloon3_irq_enabled |= (1 << balloon3_irq);
+ __raw_writel(~balloon3_irq_enabled, BALLOON3_INT_CONTROL_REG);
+}
+
+static struct irq_chip balloon3_irq_chip = {
+ .name = "FPGA",
+ .ack = balloon3_mask_irq,
+ .mask = balloon3_mask_irq,
+ .unmask = balloon3_unmask_irq,
+};
+
+static void balloon3_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+ unsigned long pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
+ balloon3_irq_enabled;
+
+ do {
+ /* clear useless edge notification */
+ if (desc->chip->ack)
+ desc->chip->ack(BALLOON3_AUX_NIRQ);
+ while (pending) {
+ irq = BALLOON3_IRQ(0) + __ffs(pending);
+ generic_handle_irq(irq);
+ pending &= pending - 1;
+ }
+ pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
+ balloon3_irq_enabled;
+ } while (pending);
+}
+
+static void __init balloon3_init_irq(void)
+{
+ int irq;
+
+ pxa27x_init_irq();
+ /* setup extra Balloon3 irqs */
+ for (irq = BALLOON3_IRQ(0); irq <= BALLOON3_IRQ(7); irq++) {
+ set_irq_chip(irq, &balloon3_irq_chip);
+ set_irq_handler(irq, handle_level_irq);
+ set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+ }
+
+ set_irq_chained_handler(BALLOON3_AUX_NIRQ, balloon3_irq_handler);
+ set_irq_type(BALLOON3_AUX_NIRQ, IRQ_TYPE_EDGE_FALLING);
+
+ pr_debug("%s: chained handler installed - irq %d automatically "
+ "enabled\n", __func__, BALLOON3_AUX_NIRQ);
+}
+
+static void balloon3_backlight_power(int on)
+{
+ pr_debug("%s: power is %s\n", __func__, on ? "on" : "off");
+ gpio_set_value(BALLOON3_GPIO_RUN_BACKLIGHT, on);
+}
+
+static unsigned long balloon3_lcd_pin_config[] = {
+ /* LCD - 16bpp Active TFT */
+ GPIO58_LCD_LDD_0,
+ GPIO59_LCD_LDD_1,
+ GPIO60_LCD_LDD_2,
+ GPIO61_LCD_LDD_3,
+ GPIO62_LCD_LDD_4,
+ GPIO63_LCD_LDD_5,
+ GPIO64_LCD_LDD_6,
+ GPIO65_LCD_LDD_7,
+ GPIO66_LCD_LDD_8,
+ GPIO67_LCD_LDD_9,
+ GPIO68_LCD_LDD_10,
+ GPIO69_LCD_LDD_11,
+ GPIO70_LCD_LDD_12,
+ GPIO71_LCD_LDD_13,
+ GPIO72_LCD_LDD_14,
+ GPIO73_LCD_LDD_15,
+ GPIO74_LCD_FCLK,
+ GPIO75_LCD_LCLK,
+ GPIO76_LCD_PCLK,
+ GPIO77_LCD_BIAS,
+
+ GPIO99_GPIO, /* Backlight */
+};
+
+static struct pxafb_mode_info balloon3_lcd_modes[] = {
+ {
+ .pixclock = 38000,
+ .xres = 480,
+ .yres = 640,
+ .bpp = 16,
+ .hsync_len = 8,
+ .left_margin = 8,
+ .right_margin = 8,
+ .vsync_len = 2,
+ .upper_margin = 4,
+ .lower_margin = 5,
+ .sync = 0,
+ },
+};
+
+static struct pxafb_mach_info balloon3_pxafb_info = {
+ .modes = balloon3_lcd_modes,
+ .num_modes = ARRAY_SIZE(balloon3_lcd_modes),
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+ .pxafb_backlight_power = balloon3_backlight_power,
+};
+
+static unsigned long balloon3_mmc_pin_config[] = {
+ GPIO32_MMC_CLK,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+ GPIO112_MMC_CMD,
+};
+
+static void balloon3_mci_setpower(struct device *dev, unsigned int vdd)
+{
+ struct pxamci_platform_data *p_d = dev->platform_data;
+
+ if ((1 << vdd) & p_d->ocr_mask) {
+ pr_debug("%s: on\n", __func__);
+ /* FIXME something to prod here? */
+ } else {
+ pr_debug("%s: off\n", __func__);
+ /* FIXME something to prod here? */
+ }
+}
+
+static struct pxamci_platform_data balloon3_mci_platform_data = {
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .setpower = balloon3_mci_setpower,
+};
+
+static int balloon3_udc_is_connected(void)
+{
+ pr_debug("%s: udc connected\n", __func__);
+ return 1;
+}
+
+static void balloon3_udc_command(int cmd)
+{
+ switch (cmd) {
+ case PXA2XX_UDC_CMD_CONNECT:
+ UP2OCR |= (UP2OCR_DPPUE + UP2OCR_DPPUBE);
+ pr_debug("%s: connect\n", __func__);
+ break;
+ case PXA2XX_UDC_CMD_DISCONNECT:
+ UP2OCR &= ~UP2OCR_DPPUE;
+ pr_debug("%s: disconnect\n", __func__);
+ break;
+ }
+}
+
+static struct pxa2xx_udc_mach_info balloon3_udc_info = {
+ .udc_is_connected = balloon3_udc_is_connected,
+ .udc_command = balloon3_udc_command,
+};
+
+static struct pxaficp_platform_data balloon3_ficp_platform_data = {
+ .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
+};
+
+static unsigned long balloon3_ohci_pin_config[] = {
+ GPIO88_USBH1_PWR,
+ GPIO89_USBH1_PEN,
+};
+
+static struct pxaohci_platform_data balloon3_ohci_platform_data = {
+ .port_mode = PMM_PERPORT_MODE,
+ .flags = ENABLE_PORT_ALL | POWER_CONTROL_LOW | POWER_SENSE_LOW,
+};
+
+static unsigned long balloon3_pin_config[] __initdata = {
+ /* Select BTUART 'COM1/ttyS0' as IO option for pins 42/43/44/45 */
+ GPIO42_BTUART_RXD,
+ GPIO43_BTUART_TXD,
+ GPIO44_BTUART_CTS,
+ GPIO45_BTUART_RTS,
+
+ /* Wakeup GPIO */
+ GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,
+
+ /* NAND & IDLE LED GPIOs */
+ GPIO9_GPIO,
+ GPIO10_GPIO,
+};
+
+static struct gpio_led balloon3_gpio_leds[] = {
+ {
+ .name = "balloon3:green:idle",
+ .default_trigger = "heartbeat",
+ .gpio = BALLOON3_GPIO_LED_IDLE,
+ .active_low = 1,
+ },
+ {
+ .name = "balloon3:green:nand",
+ .default_trigger = "nand-disk",
+ .gpio = BALLOON3_GPIO_LED_NAND,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_led_platform_data balloon3_gpio_leds_platform_data = {
+ .leds = balloon3_gpio_leds,
+ .num_leds = ARRAY_SIZE(balloon3_gpio_leds),
+};
+
+static struct platform_device balloon3led_device = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &balloon3_gpio_leds_platform_data,
+ },
+};
+
+static void __init balloon3_init(void)
+{
+ pr_info("Initialising Balloon3\n");
+
+ /* system bus arbiter setting
+ * - Core_Park
+ * - LCD_wt:DMA_wt:CORE_Wt = 2:3:4
+ */
+ ARB_CNTRL = ARB_CORE_PARK | 0x234;
+
+ pxa_set_i2c_info(NULL);
+ if (balloon3_has(BALLOON3_FEATURE_AUDIO))
+ pxa_set_ac97_info(NULL);
+
+ if (balloon3_has(BALLOON3_FEATURE_TOPPOLY)) {
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_lcd_pin_config));
+ gpio_request(BALLOON3_GPIO_RUN_BACKLIGHT,
+ "LCD Backlight Power");
+ gpio_direction_output(BALLOON3_GPIO_RUN_BACKLIGHT, 1);
+ set_pxa_fb_info(&balloon3_pxafb_info);
+ }
+
+ if (balloon3_has(BALLOON3_FEATURE_MMC)) {
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_mmc_pin_config));
+ pxa_set_mci_info(&balloon3_mci_platform_data);
+ }
+ pxa_set_ficp_info(&balloon3_ficp_platform_data);
+ if (balloon3_has(BALLOON3_FEATURE_OHCI)) {
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_ohci_pin_config));
+ pxa_set_ohci_info(&balloon3_ohci_platform_data);
+ }
+ pxa_set_udc_info(&balloon3_udc_info);
+
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_pin_config));
+
+ platform_device_register(&balloon3led_device);
+}
+
+static struct map_desc balloon3_io_desc[] __initdata = {
+ { /* CPLD/FPGA */
+ .virtual = BALLOON3_FPGA_VIRT,
+ .pfn = __phys_to_pfn(BALLOON3_FPGA_PHYS),
+ .length = BALLOON3_FPGA_LENGTH,
+ .type = MT_DEVICE,
+ },
+};
+
+static void __init balloon3_map_io(void)
+{
+ pxa_map_io();
+ iotable_init(balloon3_io_desc, ARRAY_SIZE(balloon3_io_desc));
+}
+
+MACHINE_START(BALLOON3, "Balloon3")
+ /* Maintainer: Nick Bane. */
+ .phys_io = 0x40000000,
+ .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
+ .map_io = balloon3_map_io,
+ .init_irq = balloon3_init_irq,
+ .timer = &pxa_timer,
+ .init_machine = balloon3_init,
+ .boot_params = PHYS_OFFSET + 0x100,
+MACHINE_END
unsigned int cken;
unsigned int delay;
unsigned int enabled;
- struct clk *other;
};
#define INIT_CLKREG(_clk,_devname,_conname) \
#include <linux/sysdev.h>
#include <linux/irq.h>
#include <linux/gpio.h>
+#include <linux/delay.h>
#include <linux/rtc-v3020.h>
#include <video/mbxfb.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/libertas_spi.h>
+
#include <mach/pxa27x.h>
#include <mach/ohci.h>
#include <mach/mmc.h>
+#include <mach/pxa2xx_spi.h>
#include "generic.h"
/* MMC power enable */
#define GPIO105_MMC_POWER (105)
+/* WLAN GPIOS */
+#define GPIO19_WLAN_STRAP (19)
+#define GPIO102_WLAN_RST (102)
+
static unsigned long cmx270_pin_config[] = {
/* AC'97 */
GPIO28_AC97_BITCLK,
GPIO26_SSP1_RXD,
/* SSP2 */
- GPIO19_SSP2_SCLK,
- GPIO14_SSP2_SFRM,
+ GPIO19_GPIO, /* SSP2 clock is used as GPIO for Libertas pin-strap */
+ GPIO14_GPIO,
GPIO87_SSP2_TXD,
GPIO88_SSP2_RXD,
GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH,
GPIO105_GPIO | MFP_LPM_DRIVE_HIGH, /* MMC/SD power */
GPIO53_GPIO, /* PC card reset */
+ GPIO102_GPIO, /* WLAN reset */
/* NAND controls */
GPIO11_GPIO | MFP_LPM_DRIVE_HIGH, /* NAND CE# */
/* interrupts */
GPIO10_GPIO, /* DM9000 interrupt */
GPIO83_GPIO, /* MMC card detect */
+ GPIO95_GPIO, /* WLAN interrupt */
};
/* V3020 RTC */
#endif
#if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE)
-static int cmx270_mci_init(struct device *dev,
- irq_handler_t cmx270_detect_int,
- void *data)
+static struct pxamci_platform_data cmx270_mci_platform_data = {
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = GPIO83_MMC_IRQ,
+ .gpio_card_ro = -1,
+ .gpio_power = GPIO105_MMC_POWER,
+ .gpio_power_invert = 1,
+};
+
+static void __init cmx270_init_mmc(void)
{
- int err;
+ pxa_set_mci_info(&cmx270_mci_platform_data);
+}
+#else
+static inline void cmx270_init_mmc(void) {}
+#endif
+
+#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
+static struct pxa2xx_spi_master cm_x270_spi_info = {
+ .num_chipselect = 1,
+ .enable_dma = 1,
+};
+
+static struct pxa2xx_spi_chip cm_x270_libertas_chip = {
+ .rx_threshold = 1,
+ .tx_threshold = 1,
+ .timeout = 1000,
+ .gpio_cs = 14,
+};
+
+static unsigned long cm_x270_libertas_pin_config[] = {
+ /* SSP2 */
+ GPIO19_SSP2_SCLK,
+ GPIO14_GPIO,
+ GPIO87_SSP2_TXD,
+ GPIO88_SSP2_RXD,
+
+};
- err = gpio_request(GPIO105_MMC_POWER, "MMC/SD power");
- if (err) {
- dev_warn(dev, "power gpio unavailable\n");
+static int cm_x270_libertas_setup(struct spi_device *spi)
+{
+ int err = gpio_request(GPIO19_WLAN_STRAP, "WLAN STRAP");
+ if (err)
return err;
- }
- gpio_direction_output(GPIO105_MMC_POWER, 0);
+ err = gpio_request(GPIO102_WLAN_RST, "WLAN RST");
+ if (err)
+ goto err_free_strap;
- err = request_irq(CMX270_MMC_IRQ, cmx270_detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- gpio_free(GPIO105_MMC_POWER);
- dev_err(dev, "cmx270_mci_init: MMC/SD: can't"
- " request MMC card detect IRQ\n");
- }
+ err = gpio_direction_output(GPIO102_WLAN_RST, 0);
+ if (err)
+ goto err_free_strap;
+ msleep(100);
+
+ err = gpio_direction_output(GPIO19_WLAN_STRAP, 1);
+ if (err)
+ goto err_free_strap;
+ msleep(100);
+
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(cm_x270_libertas_pin_config));
+
+ gpio_set_value(GPIO102_WLAN_RST, 1);
+ msleep(100);
+
+ spi->bits_per_word = 16;
+ spi_setup(spi);
+
+ return 0;
+
+err_free_strap:
+ gpio_free(GPIO19_WLAN_STRAP);
return err;
}
-static void cmx270_mci_setpower(struct device *dev, unsigned int vdd)
+static int cm_x270_libertas_teardown(struct spi_device *spi)
{
- struct pxamci_platform_data *p_d = dev->platform_data;
-
- if ((1 << vdd) & p_d->ocr_mask) {
- dev_dbg(dev, "power on\n");
- gpio_set_value(GPIO105_MMC_POWER, 0);
- } else {
- gpio_set_value(GPIO105_MMC_POWER, 1);
- dev_dbg(dev, "power off\n");
- }
-}
+ gpio_set_value(GPIO102_WLAN_RST, 0);
+ gpio_free(GPIO102_WLAN_RST);
+ gpio_free(GPIO19_WLAN_STRAP);
-static void cmx270_mci_exit(struct device *dev, void *data)
-{
- free_irq(CMX270_MMC_IRQ, data);
- gpio_free(GPIO105_MMC_POWER);
+ return 0;
}
-static struct pxamci_platform_data cmx270_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = cmx270_mci_init,
- .setpower = cmx270_mci_setpower,
- .exit = cmx270_mci_exit,
+struct libertas_spi_platform_data cm_x270_libertas_pdata = {
+ .use_dummy_writes = 1,
+ .setup = cm_x270_libertas_setup,
+ .teardown = cm_x270_libertas_teardown,
};
-static void __init cmx270_init_mmc(void)
+static struct spi_board_info cm_x270_spi_devices[] __initdata = {
+ {
+ .modalias = "libertas_spi",
+ .max_speed_hz = 13000000,
+ .bus_num = 2,
+ .irq = gpio_to_irq(95),
+ .chip_select = 0,
+ .controller_data = &cm_x270_libertas_chip,
+ .platform_data = &cm_x270_libertas_pdata,
+ },
+};
+
+static void __init cmx270_init_spi(void)
{
- pxa_set_mci_info(&cmx270_mci_platform_data);
+ pxa2xx_set_spi_info(2, &cm_x270_spi_info);
+ spi_register_board_info(ARRAY_AND_SIZE(cm_x270_spi_devices));
}
#else
-static inline void cmx270_init_mmc(void) {}
+static inline void cmx270_init_spi(void) {}
#endif
void __init cmx270_init(void)
cmx270_init_mmc();
cmx270_init_ohci();
cmx270_init_2700G();
+ cmx270_init_spi();
}
}
static struct pxamci_platform_data cm_x300_mci_platform_data = {
- .detect_delay = 20,
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = cm_x300_mci_init,
- .exit = cm_x300_mci_exit,
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = cm_x300_mci_init,
+ .exit = cm_x300_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
-static int cm_x300_mci2_ro(struct device *dev)
-{
- return gpio_get_value(GPIO85_MMC2_WP);
-}
-
-static int cm_x300_mci2_init(struct device *dev,
- irq_handler_t cm_x300_detect_int,
- void *data)
-{
- int err;
-
- /*
- * setup GPIO for CM-X300 MMC controller
- */
- err = gpio_request(GPIO82_MMC2_IRQ, "mmc card detect");
- if (err)
- goto err_request_cd;
- gpio_direction_input(GPIO82_MMC2_IRQ);
-
- err = gpio_request(GPIO85_MMC2_WP, "mmc write protect");
- if (err)
- goto err_request_wp;
- gpio_direction_input(GPIO85_MMC2_WP);
-
- err = request_irq(CM_X300_MMC2_IRQ, cm_x300_detect_int,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: MMC/SD/SDIO: "
- "can't request card detect IRQ\n", __func__);
- goto err_request_irq;
- }
-
- return 0;
-
-err_request_irq:
- gpio_free(GPIO85_MMC2_WP);
-err_request_wp:
- gpio_free(GPIO82_MMC2_IRQ);
-err_request_cd:
- return err;
-}
-
-static void cm_x300_mci2_exit(struct device *dev, void *data)
-{
- free_irq(CM_X300_MMC2_IRQ, data);
- gpio_free(GPIO82_MMC2_IRQ);
- gpio_free(GPIO85_MMC2_WP);
-}
-
static struct pxamci_platform_data cm_x300_mci2_platform_data = {
- .detect_delay = 20,
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = cm_x300_mci2_init,
- .exit = cm_x300_mci2_exit,
- .get_ro = cm_x300_mci2_ro,
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = GPIO82_MMC2_IRQ,
+ .gpio_card_ro = GPIO85_MMC2_WP,
+ .gpio_power = -1,
};
static void __init cm_x300_init_mmc(void)
{
colibri_pxa300_init_eth();
colibri_pxa300_init_ohci();
+ colibri_pxa3xx_init_nand();
colibri_pxa300_init_lcd();
colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO39_GPIO));
colibri_pxa310_init_ac97();
static inline void colibri_pxa320_init_ac97(void) {}
#endif
+/*
+ * The following configuration is verified to work with the Toradex Orchid
+ * carrier board
+ */
+static mfp_cfg_t colibri_pxa320_uart_pin_config[] __initdata = {
+ /* UART 1 configuration (may be set by bootloader) */
+ GPIO99_UART1_CTS,
+ GPIO104_UART1_RTS,
+ GPIO97_UART1_RXD,
+ GPIO98_UART1_TXD,
+ GPIO101_UART1_DTR,
+ GPIO103_UART1_DSR,
+ GPIO100_UART1_DCD,
+ GPIO102_UART1_RI,
+
+ /* UART 2 configuration */
+ GPIO109_UART2_CTS,
+ GPIO112_UART2_RTS,
+ GPIO110_UART2_RXD,
+ GPIO111_UART2_TXD,
+
+ /* UART 3 configuration */
+ GPIO30_UART3_RXD,
+ GPIO31_UART3_TXD,
+};
+
+static void __init colibri_pxa320_init_uart(void)
+{
+ pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa320_uart_pin_config));
+}
+
void __init colibri_pxa320_init(void)
{
colibri_pxa320_init_eth();
colibri_pxa320_init_ohci();
+ colibri_pxa3xx_init_nand();
colibri_pxa320_init_lcd();
colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO49_GPIO));
colibri_pxa320_init_ac97();
colibri_pxa3xx_init_mmc(ARRAY_AND_SIZE(colibri_pxa320_mmc_pin_config),
mfp_to_gpio(MFP_PIN_GPIO28));
+ colibri_pxa320_init_uart();
}
MACHINE_START(COLIBRI320, "Toradex Colibri PXA320")
#include <mach/colibri.h>
#include <mach/mmc.h>
#include <mach/pxafb.h>
+#include <mach/pxa3xx_nand.h>
#include "generic.h"
#include "devices.h"
}
static struct pxamci_platform_data colibri_pxa3xx_mci_platform_data = {
- .detect_delay = 20,
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .init = colibri_pxa3xx_mci_init,
- .exit = colibri_pxa3xx_mci_exit,
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .init = colibri_pxa3xx_mci_init,
+ .exit = colibri_pxa3xx_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
void __init colibri_pxa3xx_init_mmc(mfp_cfg_t *pins, int len, int detect_pin)
}
#endif
+#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+static struct mtd_partition colibri_nand_partitions[] = {
+ {
+ .name = "bootloader",
+ .offset = 0,
+ .size = SZ_512K,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_4M,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "reserved",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_1M,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "fs",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct pxa3xx_nand_platform_data colibri_nand_info = {
+ .enable_arbiter = 1,
+ .keep_config = 1,
+ .parts = colibri_nand_partitions,
+ .nr_parts = ARRAY_SIZE(colibri_nand_partitions),
+};
+
+void __init colibri_pxa3xx_init_nand(void)
+{
+ pxa3xx_set_nand_info(&colibri_nand_info);
+}
+#endif
+
#include <linux/spi/ads7846.h>
#include <linux/spi/corgi_lcd.h>
#include <linux/mtd/sharpsl.h>
+#include <linux/input/matrix_keypad.h>
#include <video/w100fb.h>
#include <asm/setup.h>
GPIO6_MMC_CLK,
GPIO8_MMC_CS0,
+ /* GPIO Matrix Keypad */
+ GPIO66_GPIO, /* column 0 */
+ GPIO67_GPIO, /* column 1 */
+ GPIO68_GPIO, /* column 2 */
+ GPIO69_GPIO, /* column 3 */
+ GPIO70_GPIO, /* column 4 */
+ GPIO71_GPIO, /* column 5 */
+ GPIO72_GPIO, /* column 6 */
+ GPIO73_GPIO, /* column 7 */
+ GPIO74_GPIO, /* column 8 */
+ GPIO75_GPIO, /* column 9 */
+ GPIO76_GPIO, /* column 10 */
+ GPIO77_GPIO, /* column 11 */
+ GPIO58_GPIO, /* row 0 */
+ GPIO59_GPIO, /* row 1 */
+ GPIO60_GPIO, /* row 2 */
+ GPIO61_GPIO, /* row 3 */
+ GPIO62_GPIO, /* row 4 */
+ GPIO63_GPIO, /* row 5 */
+ GPIO64_GPIO, /* row 6 */
+ GPIO65_GPIO, /* row 7 */
+
/* GPIO */
GPIO9_GPIO, /* CORGI_GPIO_nSD_DETECT */
GPIO7_GPIO, /* CORGI_GPIO_nSD_WP */
/*
* Corgi Keyboard Device
*/
+#define CORGI_KEY_CALENDER KEY_F1
+#define CORGI_KEY_ADDRESS KEY_F2
+#define CORGI_KEY_FN KEY_F3
+#define CORGI_KEY_CANCEL KEY_F4
+#define CORGI_KEY_OFF KEY_SUSPEND
+#define CORGI_KEY_EXOK KEY_F5
+#define CORGI_KEY_EXCANCEL KEY_F6
+#define CORGI_KEY_EXJOGDOWN KEY_F7
+#define CORGI_KEY_EXJOGUP KEY_F8
+#define CORGI_KEY_JAP1 KEY_LEFTCTRL
+#define CORGI_KEY_JAP2 KEY_LEFTALT
+#define CORGI_KEY_MAIL KEY_F10
+#define CORGI_KEY_OK KEY_F11
+#define CORGI_KEY_MENU KEY_F12
+
+static const uint32_t corgikbd_keymap[] = {
+ KEY(0, 1, KEY_1),
+ KEY(0, 2, KEY_3),
+ KEY(0, 3, KEY_5),
+ KEY(0, 4, KEY_6),
+ KEY(0, 5, KEY_7),
+ KEY(0, 6, KEY_9),
+ KEY(0, 7, KEY_0),
+ KEY(0, 8, KEY_BACKSPACE),
+ KEY(1, 1, KEY_2),
+ KEY(1, 2, KEY_4),
+ KEY(1, 3, KEY_R),
+ KEY(1, 4, KEY_Y),
+ KEY(1, 5, KEY_8),
+ KEY(1, 6, KEY_I),
+ KEY(1, 7, KEY_O),
+ KEY(1, 8, KEY_P),
+ KEY(2, 0, KEY_TAB),
+ KEY(2, 1, KEY_Q),
+ KEY(2, 2, KEY_E),
+ KEY(2, 3, KEY_T),
+ KEY(2, 4, KEY_G),
+ KEY(2, 5, KEY_U),
+ KEY(2, 6, KEY_J),
+ KEY(2, 7, KEY_K),
+ KEY(3, 0, CORGI_KEY_CALENDER),
+ KEY(3, 1, KEY_W),
+ KEY(3, 2, KEY_S),
+ KEY(3, 3, KEY_F),
+ KEY(3, 4, KEY_V),
+ KEY(3, 5, KEY_H),
+ KEY(3, 6, KEY_M),
+ KEY(3, 7, KEY_L),
+ KEY(3, 9, KEY_RIGHTSHIFT),
+ KEY(4, 0, CORGI_KEY_ADDRESS),
+ KEY(4, 1, KEY_A),
+ KEY(4, 2, KEY_D),
+ KEY(4, 3, KEY_C),
+ KEY(4, 4, KEY_B),
+ KEY(4, 5, KEY_N),
+ KEY(4, 6, KEY_DOT),
+ KEY(4, 8, KEY_ENTER),
+ KEY(4, 10, KEY_LEFTSHIFT),
+ KEY(5, 0, CORGI_KEY_MAIL),
+ KEY(5, 1, KEY_Z),
+ KEY(5, 2, KEY_X),
+ KEY(5, 3, KEY_MINUS),
+ KEY(5, 4, KEY_SPACE),
+ KEY(5, 5, KEY_COMMA),
+ KEY(5, 7, KEY_UP),
+ KEY(5, 11, CORGI_KEY_FN),
+ KEY(6, 0, KEY_SYSRQ),
+ KEY(6, 1, CORGI_KEY_JAP1),
+ KEY(6, 2, CORGI_KEY_JAP2),
+ KEY(6, 3, CORGI_KEY_CANCE
Code Review / linux-2.6.git / commitdiff