+static int dbgp_ehci_startup(void)
+{
+ u32 ctrl, cmd, status;
+ int loop;
+
+ /* Claim ownership, but do not enable yet */
+ ctrl = readl(&ehci_debug->control);
+ ctrl |= DBGP_OWNER;
+ ctrl &= ~(DBGP_ENABLED | DBGP_INUSE);
+ writel(ctrl, &ehci_debug->control);
+ udelay(1);
+
+ dbgp_ehci_status("EHCI startup");
+ /* Start the ehci running */
+ cmd = readl(&ehci_regs->command);
+ cmd &= ~(CMD_LRESET | CMD_IAAD | CMD_PSE | CMD_ASE | CMD_RESET);
+ cmd |= CMD_RUN;
+ writel(cmd, &ehci_regs->command);
+
+ /* Ensure everything is routed to the EHCI */
+ writel(FLAG_CF, &ehci_regs->configured_flag);
+
+ /* Wait until the controller is no longer halted */
+ loop = 10;
+ do {
+ status = readl(&ehci_regs->status);
+ if (!(status & STS_HALT))
+ break;
+ udelay(1);
+ } while (--loop > 0);
+
+ if (!loop) {
+ dbgp_printk("ehci can not be started\n");
+ return -ENODEV;
+ }
+ dbgp_printk("ehci started\n");
+ return 0;
+}
+
+static int dbgp_ehci_controller_reset(void)
+{
+ int loop = 250 * 1000;
+ u32 cmd;
+
+ /* Reset the EHCI controller */
+ cmd = readl(&ehci_regs->command);
+ cmd |= CMD_RESET;
+ writel(cmd, &ehci_regs->command);
+ do {
+ cmd = readl(&ehci_regs->command);
+ } while ((cmd & CMD_RESET) && (--loop > 0));
+
+ if (!loop) {
+ dbgp_printk("can not reset ehci\n");
+ return -1;
+ }
+ dbgp_ehci_status("ehci reset done");
+ return 0;
+}
+static int ehci_wait_for_port(int port);
+/* Return 0 on success
+ * Return -ENODEV for any general failure
+ * Return -EIO if wait for port fails
+ */
+int dbgp_external_startup(void)
+{
+ int devnum;
+ struct usb_debug_descriptor dbgp_desc;
+ int ret;
+ u32 ctrl, portsc;
+ int dbg_port = dbgp_phys_port;
+ int tries = 3;
+
+ ret = dbgp_ehci_startup();
+ if (ret)
+ return ret;
+
+ /* Wait for a device to show up in the debug port */
+ ret = ehci_wait_for_port(dbg_port);
+ if (ret < 0) {
+ portsc = readl(&ehci_regs->port_status[dbg_port - 1]);
+ dbgp_printk("No device found in debug port\n");
+ return -EIO;
+ }
+ dbgp_ehci_status("wait for port done");
+
+ /* Enable the debug port */
+ ctrl = readl(&ehci_debug->control);
+ ctrl |= DBGP_CLAIM;
+ writel(ctrl, &ehci_debug->control);
+ ctrl = readl(&ehci_debug->control);
+ if ((ctrl & DBGP_CLAIM) != DBGP_CLAIM) {
+ dbgp_printk("No device in debug port\n");
+ writel(ctrl & ~DBGP_CLAIM, &ehci_debug->control);
+ return -ENODEV;
+ }
+ dbgp_ehci_status("debug ported enabled");
+
+ /* Completely transfer the debug device to the debug controller */
+ portsc = readl(&ehci_regs->port_status[dbg_port - 1]);
+ portsc &= ~PORT_PE;
+ writel(portsc, &ehci_regs->port_status[dbg_port - 1]);
+
+ dbgp_mdelay(100);
+
+try_again:
+ /* Find the debug device and make it device number 127 */
+ for (devnum = 0; devnum <= 127; devnum++) {
+ ret = dbgp_control_msg(devnum,
+ USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
+ USB_REQ_GET_DESCRIPTOR, (USB_DT_DEBUG << 8), 0,
+ &dbgp_desc, sizeof(dbgp_desc));
+ if (ret > 0)
+ break;
+ }
+ if (devnum > 127) {
+ dbgp_printk("Could not find attached debug device\n");
+ goto err;
+ }
+ if (ret < 0) {
+ dbgp_printk("Attached device is not a debug device\n");
+ goto err;
+ }
+ dbgp_endpoint_out = dbgp_desc.bDebugOutEndpoint;
+
+ /* Move the device to 127 if it isn't already there */
+ if (devnum != USB_DEBUG_DEVNUM) {
+ ret = dbgp_control_msg(devnum,
+ USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
+ USB_REQ_SET_ADDRESS, USB_DEBUG_DEVNUM, 0, NULL, 0);
+ if (ret < 0) {
+ dbgp_printk("Could not move attached device to %d\n",
+ USB_DEBUG_DEVNUM);
+ goto err;
+ }
+ devnum = USB_DEBUG_DEVNUM;
+ dbgp_printk("debug device renamed to 127\n");
+ }
+
+ /* Enable the debug interface */
+ ret = dbgp_control_msg(USB_DEBUG_DEVNUM,
+ USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE,
+ USB_REQ_SET_FEATURE, USB_DEVICE_DEBUG_MODE, 0, NULL, 0);
+ if (ret < 0) {
+ dbgp_printk(" Could not enable the debug device\n");
+ goto err;
+ }
+ dbgp_printk("debug interface enabled\n");
+ /* Perform a small write to get the even/odd data state in sync
+ */
+ ret = dbgp_bulk_write(USB_DEBUG_DEVNUM, dbgp_endpoint_out, " ", 1);
+ if (ret < 0) {
+ dbgp_printk("dbgp_bulk_write failed: %d\n", ret);
+ goto err;
+ }
+ dbgp_printk("small write doned\n");
+ dbgp_not_safe = 0;
+
+ return 0;
+err:
+ if (tries--)
+ goto try_again;
+ return -ENODEV;
+}
+EXPORT_SYMBOL_GPL(dbgp_external_startup);
+
Code Review / linux-2.6.git / blobdiff