/*
- * linux/drivers/ide/pci/siimage.c Version 1.15 Jun 29 2007
+ * linux/drivers/ide/pci/siimage.c Version 1.18 Oct 18 2007
*
* Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2003 Red Hat <alan@redhat.com>
*
* If you have strange problems with nVidia chipset systems please
* see the SI support documentation and update your system BIOS
- * if neccessary
+ * if necessary
*
* The Dell DRAC4 has some interesting features including effectively hot
* unplugging/replugging the virtual CD interface when the DRAC is reset.
static int pdev_is_sata(struct pci_dev *pdev)
{
- switch(pdev->device)
- {
+#ifdef CONFIG_BLK_DEV_IDE_SATA
+ switch(pdev->device) {
case PCI_DEVICE_ID_SII_3112:
case PCI_DEVICE_ID_SII_1210SA:
return 1;
return 0;
}
BUG();
+#endif
return 0;
}
-
+
/**
* is_sata - check if hwif is SATA
* @hwif: interface to check
* SI3112 SATA controller life is a bit simpler.
*/
-static u8 sil_udma_filter(ide_drive_t *drive)
+static u8 sil_pata_udma_filter(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
unsigned long base = (unsigned long) hwif->hwif_data;
else
pci_read_config_byte(hwif->pci_dev, 0x8A, &scsc);
- if (is_sata(hwif)) {
- mask = strstr(drive->id->model, "Maxtor") ? 0x3f : 0x7f;
- goto out;
- }
-
if ((scsc & 0x30) == 0x10) /* 133 */
- mask = 0x7f;
+ mask = ATA_UDMA6;
else if ((scsc & 0x30) == 0x20) /* 2xPCI */
- mask = 0x7f;
+ mask = ATA_UDMA6;
else if ((scsc & 0x30) == 0x00) /* 100 */
- mask = 0x3f;
+ mask = ATA_UDMA5;
else /* Disabled ? */
BUG();
-out:
+
return mask;
}
+static u8 sil_sata_udma_filter(ide_drive_t *drive)
+{
+ return strstr(drive->id->model, "Maxtor") ? ATA_UDMA5 : ATA_UDMA6;
+}
+
/**
- * sil_tune_pio - tune a drive
- * @drive: drive to tune
- * @pio: the desired PIO mode
+ * sil_set_pio_mode - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
* Load the timing settings for this device mode into the
* controller. If we are in PIO mode 3 or 4 turn on IORDY
* monitoring (bit 9). The TF timing is bits 31:16
*/
-static void sil_tune_pio(ide_drive_t *drive, u8 pio)
+static void sil_set_pio_mode(ide_drive_t *drive, u8 pio)
{
const u16 tf_speed[] = { 0x328a, 0x2283, 0x1281, 0x10c3, 0x10c1 };
const u16 data_speed[] = { 0x328a, 0x2283, 0x1104, 0x10c3, 0x10c1 };
ide_hwif_t *hwif = HWIF(drive);
- ide_drive_t *pair = &hwif->drives[drive->dn ^ 1];
+ ide_drive_t *pair = ide_get_paired_drive(drive);
u32 speedt = 0;
u16 speedp = 0;
unsigned long addr = siimage_seldev(drive, 0x04);
unsigned long tfaddr = siimage_selreg(hwif, 0x02);
+ unsigned long base = (unsigned long)hwif->hwif_data;
u8 tf_pio = pio;
+ u8 addr_mask = hwif->channel ? (hwif->mmio ? 0xF4 : 0x84)
+ : (hwif->mmio ? 0xB4 : 0x80);
+ u8 mode = 0;
+ u8 unit = drive->select.b.unit;
/* trim *taskfile* PIO to the slowest of the master/slave */
if (pair->present) {
hwif->OUTW(hwif->INW(tfaddr-2)|0x200, tfaddr-2);
else
hwif->OUTW(hwif->INW(tfaddr-2)&~0x200, tfaddr-2);
+
+ mode = hwif->INB(base + addr_mask);
+ mode &= ~(unit ? 0x30 : 0x03);
+ mode |= (unit ? 0x10 : 0x01);
+ hwif->OUTB(mode, base + addr_mask);
} else {
pci_write_config_word(hwif->pci_dev, addr, speedp);
pci_write_config_word(hwif->pci_dev, tfaddr, speedt);
if (pio > 2)
speedp |= 0x200;
pci_write_config_word(hwif->pci_dev, tfaddr-2, speedp);
- }
-}
-static void sil_tuneproc(ide_drive_t *drive, u8 pio)
-{
- pio = ide_get_best_pio_mode(drive, pio, 4);
- sil_tune_pio(drive, pio);
- (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
+ pci_read_config_byte(hwif->pci_dev, addr_mask, &mode);
+ mode &= ~(unit ? 0x30 : 0x03);
+ mode |= (unit ? 0x10 : 0x01);
+ pci_write_config_byte(hwif->pci_dev, addr_mask, mode);
+ }
}
/**
- * siimage_tune_chipset - set controller timings
- * @drive: Drive to set up
- * @xferspeed: speed we want to achieve
+ * sil_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
- * Tune the SII chipset for the desired mode. If we can't achieve
- * the desired mode then tune for a lower one, but ultimately
- * make the thing work.
+ * Tune the SiI chipset for the desired DMA mode.
*/
-
-static int siimage_tune_chipset (ide_drive_t *drive, byte xferspeed)
+
+static void sil_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
u8 ultra6[] = { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 };
u8 ultra5[] = { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01 };
ide_hwif_t *hwif = HWIF(drive);
u16 ultra = 0, multi = 0;
u8 mode = 0, unit = drive->select.b.unit;
- u8 speed = ide_rate_filter(drive, xferspeed);
unsigned long base = (unsigned long)hwif->hwif_data;
u8 scsc = 0, addr_mask = ((hwif->channel) ?
((hwif->mmio) ? 0xF4 : 0x84) :
scsc = is_sata(hwif) ? 1 : scsc;
switch(speed) {
- case XFER_PIO_4:
- case XFER_PIO_3:
- case XFER_PIO_2:
- case XFER_PIO_1:
- case XFER_PIO_0:
- sil_tune_pio(drive, speed - XFER_PIO_0);
- mode |= ((unit) ? 0x10 : 0x01);
- break;
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_MW_DMA_0:
mode |= ((unit) ? 0x30 : 0x03);
break;
default:
- return 1;
+ return;
}
if (hwif->mmio) {
pci_write_config_word(hwif->pci_dev, ma, multi);
pci_write_config_word(hwif->pci_dev, ua, ultra);
}
- return (ide_config_drive_speed(drive, speed));
-}
-
-/**
- * siimage_configure_drive_for_dma - set up for DMA transfers
- * @drive: drive we are going to set up
- *
- * Set up the drive for DMA, tune the controller and drive as
- * required. If the drive isn't suitable for DMA or we hit
- * other problems then we will drop down to PIO and set up
- * PIO appropriately
- */
-
-static int siimage_config_drive_for_dma (ide_drive_t *drive)
-{
- if (ide_tune_dma(drive))
- return 0;
-
- if (ide_use_fast_pio(drive))
- sil_tuneproc(drive, 255);
-
- return -1;
}
/* returns 1 if dma irq issued, 0 otherwise */
static int siimage_mmio_ide_dma_test_irq (ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
- unsigned long base = (unsigned long)hwif->hwif_data;
unsigned long addr = siimage_selreg(hwif, 0x1);
if (SATA_ERROR_REG) {
+ unsigned long base = (unsigned long)hwif->hwif_data;
+
u32 ext_stat = readl((void __iomem *)(base + 0x10));
u8 watchdog = 0;
if (ext_stat & ((hwif->channel) ? 0x40 : 0x10)) {
}
/**
- * siimage_busproc - bus isolation ioctl
+ * sil_sata_busproc - bus isolation IOCTL
* @drive: drive to isolate/restore
* @state: bus state to set
*
* SATA controller the work required is quite limited, we
* just have to clean up the statistics
*/
-
-static int siimage_busproc (ide_drive_t * drive, int state)
+
+static int sil_sata_busproc(ide_drive_t * drive, int state)
{
ide_hwif_t *hwif = HWIF(drive);
u32 stat_config = 0;
}
/**
- * siimage_reset_poll - wait for sata reset
+ * sil_sata_reset_poll - wait for SATA reset
* @drive: drive we are resetting
*
* Poll the SATA phy and see whether it has come back from the dead
* yet.
*/
-
-static int siimage_reset_poll (ide_drive_t *drive)
+
+static int sil_sata_reset_poll(ide_drive_t *drive)
{
if (SATA_STATUS_REG) {
ide_hwif_t *hwif = HWIF(drive);
HWGROUP(drive)->polling = 0;
return ide_started;
}
- return 0;
- } else {
- return 0;
}
+
+ return 0;
}
/**
- * siimage_pre_reset - reset hook
+ * sil_sata_pre_reset - reset hook
* @drive: IDE device being reset
*
* For the SATA devices we need to handle recalibration/geometry
* differently
*/
-
-static void siimage_pre_reset (ide_drive_t *drive)
-{
- if (drive->media != ide_disk)
- return;
- if (is_sata(HWIF(drive)))
- {
+static void sil_sata_pre_reset(ide_drive_t *drive)
+{
+ if (drive->media == ide_disk) {
drive->special.b.set_geometry = 0;
drive->special.b.recalibrate = 0;
}
drive->failures++;
}
}
-
}
/**
static unsigned int __devinit init_chipset_siimage(struct pci_dev *dev, const char *name)
{
- u32 class_rev = 0;
- u8 tmpbyte = 0;
- u8 BA5_EN = 0;
+ u8 rev = dev->revision, tmpbyte = 0, BA5_EN = 0;
- pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
- class_rev &= 0xff;
- pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (class_rev) ? 1 : 255);
+ pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, rev ? 1 : 255);
pci_read_config_byte(dev, 0x8A, &BA5_EN);
if ((BA5_EN & 0x01) || (pci_resource_start(dev, 5))) {
hwif->sata_misc[SATA_IEN_OFFSET] = base + 0x148;
}
- hw.irq = hwif->pci_dev->irq;
+ memcpy(hwif->io_ports, hw.io_ports, sizeof(hwif->io_ports));
- memcpy(&hwif->hw, &hw, sizeof(hw));
- memcpy(hwif->io_ports, hwif->hw.io_ports, sizeof(hwif->hw.io_ports));
+ hwif->irq = dev->irq;
- hwif->irq = hw.irq;
-
- base = (unsigned long) addr;
-
- hwif->dma_base = base + (ch ? 0x08 : 0x00);
+ hwif->dma_base = (unsigned long)addr + (ch ? 0x08 : 0x00);
hwif->mmio = 1;
}
static void __devinit init_iops_siimage(ide_hwif_t *hwif)
{
- struct pci_dev *dev = hwif->pci_dev;
- u32 class_rev = 0;
-
- pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
- class_rev &= 0xff;
-
hwif->hwif_data = NULL;
/* Pessimal until we finish probing */
hwif->rqsize = 15;
- if (pci_get_drvdata(dev) == NULL)
+ if (pci_get_drvdata(hwif->pci_dev) == NULL)
return;
+
init_mmio_iops_siimage(hwif);
}
static void __devinit init_hwif_siimage(ide_hwif_t *hwif)
{
- hwif->autodma = 0;
-
+ u8 sata = is_sata(hwif);
+
hwif->resetproc = &siimage_reset;
- hwif->speedproc = &siimage_tune_chipset;
- hwif->tuneproc = &sil_tuneproc;
- hwif->reset_poll = &siimage_reset_poll;
- hwif->pre_reset = &siimage_pre_reset;
- hwif->udma_filter = &sil_udma_filter;
+ hwif->set_pio_mode = &sil_set_pio_mode;
+ hwif->set_dma_mode = &sil_set_dma_mode;
- if(is_sata(hwif)) {
+ if (sata) {
static int first = 1;
- hwif->busproc = &siimage_busproc;
+ hwif->busproc = &sil_sata_busproc;
+ hwif->reset_poll = &sil_sata_reset_poll;
+ hwif->pre_reset = &sil_sata_pre_reset;
+ hwif->udma_filter = &sil_sata_udma_filter;
if (first) {
printk(KERN_INFO "siimage: For full SATA support you should use the libata sata_sil module.\n");
first = 0;
}
- }
-
- hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
+ } else
+ hwif->udma_filter = &sil_pata_udma_filter;
if (hwif->dma_base == 0)
return;
- hwif->ultra_mask = 0x7f;
- hwif->mwdma_mask = 0x07;
-
- if (!is_sata(hwif))
- hwif->atapi_dma = 1;
-
- hwif->ide_dma_check = &siimage_config_drive_for_dma;
+ if (sata)
+ hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
if (hwif->cbl != ATA_CBL_PATA40_SHORT)
hwif->cbl = ata66_siimage(hwif);
} else {
hwif->ide_dma_test_irq = & siimage_io_ide_dma_test_irq;
}
-
- /*
- * The BIOS often doesn't set up DMA on this controller
- * so we always do it.
- */
-
- hwif->autodma = 1;
- hwif->drives[0].autodma = hwif->autodma;
- hwif->drives[1].autodma = hwif->autodma;
}
#define DECLARE_SII_DEV(name_str) \
.init_iops = init_iops_siimage, \
.init_hwif = init_hwif_siimage, \
.fixup = siimage_fixup, \
- .autodma = AUTODMA, \
- .bootable = ON_BOARD, \
+ .host_flags = IDE_HFLAG_BOOTABLE, \
.pio_mask = ATA_PIO4, \
+ .mwdma_mask = ATA_MWDMA2, \
+ .udma_mask = ATA_UDMA6, \
}
-static ide_pci_device_t siimage_chipsets[] __devinitdata = {
+static const struct ide_port_info siimage_chipsets[] __devinitdata = {
/* 0 */ DECLARE_SII_DEV("SiI680"),
/* 1 */ DECLARE_SII_DEV("SiI3112 Serial ATA"),
/* 2 */ DECLARE_SII_DEV("Adaptec AAR-1210SA")
return ide_setup_pci_device(dev, &siimage_chipsets[id->driver_data]);
}
-static struct pci_device_id siimage_pci_tbl[] = {
- { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+static const struct pci_device_id siimage_pci_tbl[] = {
+ { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_680), 0 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
- { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_3112, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
- { PCI_VENDOR_ID_CMD, PCI_DEVICE_ID_SII_1210SA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
+ { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_3112), 1 },
+ { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_1210SA), 2 },
#endif
{ 0, },
};
Code Review / linux-2.6.git / blobdiff