if ETRAXFS menu "ETRAX FS options" depends on ETRAXFS config ETRAX_DRAM_VIRTUAL_BASE hex depends on ETRAX_ARCH_V32 default "c0000000" config ETRAX_SERIAL_PORTS int default 4 config ETRAX_MEM_GRP1_CONFIG hex "MEM_GRP1_CONFIG" depends on ETRAX_ARCH_V32 default "4044a" help Waitstates for flash. The default value is suitable for the standard flashes used in axis products (120 ns). config ETRAX_MEM_GRP2_CONFIG hex "MEM_GRP2_CONFIG" depends on ETRAX_ARCH_V32 default "0" help Waitstates for SRAM. 0 is a good choice for most Axis products. config ETRAX_MEM_GRP3_CONFIG hex "MEM_GRP3_CONFIG" depends on ETRAX_ARCH_V32 default "0" help Waitstates for CSP0-3. 0 is a good choice for most Axis products. It may need to be changed if external devices such as extra register-mapped LEDs are used. config ETRAX_MEM_GRP4_CONFIG hex "MEM_GRP4_CONFIG" depends on ETRAX_ARCH_V32 default "0" help Waitstates for CSP4-6. 0 is a good choice for most Axis products. config ETRAX_SDRAM_GRP0_CONFIG hex "SDRAM_GRP0_CONFIG" depends on ETRAX_ARCH_V32 default "336" help SDRAM configuration for group 0. The value depends on the hardware configuration. The default value is suitable for 32 MB organized as two 16 bits chips (e.g. Axis part number 18550) connected as one 32 bit device (i.e. in the same group). config ETRAX_SDRAM_GRP1_CONFIG hex "SDRAM_GRP1_CONFIG" depends on ETRAX_ARCH_V32 default "0" help SDRAM configuration for group 1. The defult value is 0 because group 1 is not used in the default configuration, described in the help for SDRAM_GRP0_CONFIG. config ETRAX_SDRAM_TIMING hex "SDRAM_TIMING" depends on ETRAX_ARCH_V32 default "104a" help SDRAM timing parameters. The default value is ok for most hardwares but large SDRAMs may require a faster refresh (a.k.a 8K refresh). The default value implies 100MHz clock and SDR mode. config ETRAX_SDRAM_COMMAND hex "SDRAM_COMMAND" depends on ETRAX_ARCH_V32 default "0" help SDRAM command. Should be 0 unless you really know what you are doing (may be != 0 for unusual address line mappings such as in a MCM).. config ETRAX_DEF_GIO_PA_OE hex "GIO_PA_OE" depends on ETRAX_ARCH_V32 default "1c" help Configures the direction of general port A bits. 1 is out, 0 is in. This is often totally different depending on the product used. There are some guidelines though - if you know that only LED's are connected to port PA, then they are usually connected to bits 2-4 and you can therefore use 1c. On other boards which don't have the LED's at the general ports, these bits are used for all kinds of stuff. If you don't know what to use, it is always safe to put all as inputs, although floating inputs isn't good. config ETRAX_DEF_GIO_PA_OUT hex "GIO_PA_OUT" depends on ETRAX_ARCH_V32 default "00" help Configures the initial data for the general port A bits. Most products should use 00 here. config ETRAX_DEF_GIO_PB_OE hex "GIO_PB_OE" depends on ETRAX_ARCH_V32 default "00000" help Configures the direction of general port B bits. 1 is out, 0 is in. This is often totally different depending on the product used. There are some guidelines though - if you know that only LED's are connected to port PA, then they are usually connected to bits 2-4 and you can therefore use 1c. On other boards which don't have the LED's at the general ports, these bits are used for all kinds of stuff. If you don't know what to use, it is always safe to put all as inputs, although floating inputs isn't good. config ETRAX_DEF_GIO_PB_OUT hex "GIO_PB_OUT" depends on ETRAX_ARCH_V32 default "00000" help Configures the initial data for the general port B bits. Most products should use 00000 here. config ETRAX_DEF_GIO_PC_OE hex "GIO_PC_OE" depends on ETRAX_ARCH_V32 default "00000" help Configures the direction of general port C bits. 1 is out, 0 is in. This is often totally different depending on the product used. There are some guidelines though - if you know that only LED's are connected to port PA, then they are usually connected to bits 2-4 and you can therefore use 1c. On other boards which don't have the LED's at the general ports, these bits are used for all kinds of stuff. If you don't know what to use, it is always safe to put all as inputs, although floating inputs isn't good. config ETRAX_DEF_GIO_PC_OUT hex "GIO_PC_OUT" depends on ETRAX_ARCH_V32 default "00000" help Configures the initial data for the general port C bits. Most products should use 00000 here. config ETRAX_DEF_GIO_PD_OE hex "GIO_PD_OE" depends on ETRAX_ARCH_V32 default "00000" help Configures the direction of general port D bits. 1 is out, 0 is in. This is often totally different depending on the product used. There are some guidelines though - if you know that only LED's are connected to port PA, then they are usually connected to bits 2-4 and you can therefore use 1c. On other boards which don't have the LED's at the general ports, these bits are used for all kinds of stuff. If you don't know what to use, it is always safe to put all as inputs, although floating inputs isn't good. config ETRAX_DEF_GIO_PD_OUT hex "GIO_PD_OUT" depends on ETRAX_ARCH_V32 default "00000" help Configures the initial data for the general port D bits. Most products should use 00000 here. config ETRAX_DEF_GIO_PE_OE hex "GIO_PE_OE" depends on ETRAX_ARCH_V32 default "00000" help Configures the direction of general port E bits. 1 is out, 0 is in. This is often totally different depending on the product used. There are some guidelines though - if you know that only LED's are connected to port PA, then they are usually connected to bits 2-4 and you can therefore use 1c. On other boards which don't have the LED's at the general ports, these bits are used for all kinds of stuff. If you don't know what to use, it is always safe to put all as inputs, although floating inputs isn't good. config ETRAX_DEF_GIO_PE_OUT hex "GIO_PE_OUT" depends on ETRAX_ARCH_V32 default "00000" help Configures the initial data for the general port E bits. Most products should use 00000 here. config ETRAX_DEF_GIO_PV_OE hex "GIO_PV_OE" depends on ETRAX_VIRTUAL_GPIO default "0000" help Configures the direction of virtual general port V bits. 1 is out, 0 is in. This is often totally different depending on the product used. These bits are used for all kinds of stuff. If you don't know what to use, it is always safe to put all as inputs, although floating inputs isn't good. config ETRAX_DEF_GIO_PV_OUT hex "GIO_PV_OUT" depends on ETRAX_VIRTUAL_GPIO default "0000" help Configures the initial data for the virtual general port V bits. Most products should use 0000 here. endmenu endif