12 years agoPNP: whitespace/coding style fixes
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:02 +0000]
PNP: whitespace/coding style fixes

No functional change; just make a couple declarations
consistent with the rest of the file.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>

12 years agoPNP: add pnp_possible_config() -- can a device could be configured this way?
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:01 +0000]
PNP: add pnp_possible_config() -- can a device could be configured this way?

As part of a heuristic to identify modem devices, 8250_pnp.c
checks to see whether a device can be configured at any of the
legacy COM port addresses.

This patch moves the code that traverses the PNP "possible resource
options" from 8250_pnp.c to the PNP subsystem.  This encapsulation
is important because a future patch will change the implementation
of those resource options.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>

12 years agoPNP: dont sort by type in /sys/.../resources
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:00 +0000]
PNP: dont sort by type in /sys/.../resources

Rather than stepping through all IO resources, then stepping through
all MMIO resources, etc., we can just iterate over the resource list
once directly.

This can change the order in /sys, e.g.,

    # cat /sys/devices/pnp0/00:07/resources     # OLD
    state = active
    io 0x3f8-0x3ff
    irq 4

    # cat /sys/devices/pnp0/00:07/resources     # NEW
    state = active
    irq 4
    io 0x3f8-0x3ff

The old code artificially sorted resources by type; the new code
just lists them in the order we read them from the ISAPNP hardware
or the BIOS.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoPNP: remove ratelimit on add resource failures
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:59 +0000]
PNP: remove ratelimit on add resource failures

We used to have a fixed-size resource table.  If a device had
twenty resources when the table only had space for ten, we didn't
need ten warnings, so we added the ratelimit.

Now that we can dynamically allocate new resources, we should
only get failures if the allocation fails.  That should be
rare enough that we don't need to ratelimit the messages.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoPNPACPI: keep disabled resources when parsing current config
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:58 +0000]
PNPACPI: keep disabled resources when parsing current config

When we parse a device's _CRS data (the current resource settings),
we should keep track of everything we find, even if it's currently
disabled or invalid.

This is what we already do for ISAPNP and PNPBIOS, and it helps
keep things matched up when we subsequently re-encode resources.
For example, consider a device with (mem, irq0, irq1, io), where
irq0 is disabled.  If we drop irq0 when parsing the _CRS, we will
mistakenly put irq1 in the irq0 slot when we encode resources
for an _SRS call.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoPNP: replace pnp_resource_table with dynamically allocated resources
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:57 +0000]
PNP: replace pnp_resource_table with dynamically allocated resources

PNP used to have a fixed-size pnp_resource_table for tracking the
resources used by a device.  This table often overflowed, so we've
had to increase the table size, which wastes memory because most
devices have very few resources.

This patch replaces the table with a linked list of resources where
the entries are allocated on demand.

This removes messages like these:

    pnpacpi: exceeded the max number of IO resources
    00:01: too many I/O port resources

References:

    http://bugzilla.kernel.org/show_bug.cgi?id=9535
    http://bugzilla.kernel.org/show_bug.cgi?id=9740
    http://lkml.org/lkml/2007/11/30/110

This patch also changes the way PNP uses the IORESOURCE_UNSET,
IORESOURCE_AUTO, and IORESOURCE_DISABLED flags.

Prior to this patch, the pnp_resource_table entries used the flags
like this:

    IORESOURCE_UNSET
This table entry is unused and available for use.  When this flag
is set, we shouldn't look at anything else in the resource structure.
This flag is set when a resource table entry is initialized.

    IORESOURCE_AUTO
This resource was assigned automatically by pnp_assign_{io,mem,etc}().

This flag is set when a resource table entry is initialized and
cleared whenever we discover a resource setting by reading an ISAPNP
config register, parsing a PNPBIOS resource data stream, parsing an
ACPI _CRS list, or interpreting a sysfs "set" command.

Resources marked IORESOURCE_AUTO are reinitialized and marked as
IORESOURCE_UNSET by pnp_clean_resource_table() in these cases:

    - before we attempt to assign resources automatically,
    - if we fail to assign resources automatically,
    - after disabling a device

    IORESOURCE_DISABLED
Set by pnp_assign_{io,mem,etc}() when automatic assignment fails.
Also set by PNPBIOS and PNPACPI for:

    - invalid IRQs or GSI registration failures
    - invalid DMA channels
    - I/O ports above 0x10000
    - mem ranges with negative length

After this patch, there is no pnp_resource_table, and the resource list
entries use the flags like this:

    IORESOURCE_UNSET
This flag is no longer used in PNP.  Instead of keeping
IORESOURCE_UNSET entries in the resource list, we remove
entries from the list and free them.

    IORESOURCE_AUTO
No change in meaning: it still means the resource was assigned
automatically by pnp_assign_{port,mem,etc}(), but these functions
now set the bit explicitly.

We still "clean" a device's resource list in the same places,
but rather than reinitializing IORESOURCE_AUTO entries, we
just remove them from the list.

Note that IORESOURCE_AUTO entries are always at the end of the
list, so removing them doesn't reorder other list entries.
This is because non-IORESOURCE_AUTO entries are added by the
ISAPNP, PNPBIOS, or PNPACPI "get resources" methods and by the
sysfs "set" command.  In each of these cases, we completely free
the resource list first.

    IORESOURCE_DISABLED
In addition to the cases where we used to set this flag, ISAPNP now
adds an IORESOURCE_DISABLED resource when it reads a configuration
register with a "disabled" value.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoPNP: make pnp_{port,mem,etc}_start(), et al work for invalid resources
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:56 +0000]
PNP: make pnp_{port,mem,etc}_start(), et al work for invalid resources

Some callers use pnp_port_start() and similar functions without
making sure the resource is valid.  This patch makes us fall
back to returning the initial values if the resource is not
valid or not even present.

This mostly preserves the previous behavior, where we would just
return the initial values set by pnp_init_resource_table().  The
original 2.6.25 code didn't range-check the "bar", so it would
return garbage if the bar exceeded the table size.  This code
returns sensible values instead.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoPNP: add pnp_resource_type_name() helper function
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:55 +0000]
PNP: add pnp_resource_type_name() helper function

This patch adds a "pnp_resource_type_name(struct resource *)" that
returns the string resource type.  This will be used by the sysfs
"show resources" function and the debug resource dump function.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoPNP: add pnp_resource_type() internal interface
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:54 +0000]
PNP: add pnp_resource_type() internal interface

Given a struct resource, this returns the type (IO, MEM, IRQ, DMA).

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoPNP: remove pnp_resource.index
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:53 +0000]
PNP: remove pnp_resource.index

We used pnp_resource.index to keep track of which ISAPNP configuration
register a resource should be written to.  We needed this only to
handle the case where a register is disabled but a subsequent register
in the same set is enabled.

Rather than explicitly maintaining the pnp_resource.index, this patch
adds a resource every time we read an ISAPNP configuration register
and marks the resource as IORESOURCE_DISABLED when appropriate.  This
makes the position in the pnp_resource_table always correspond to the
config register index.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoPNP: add detail to debug resource dump
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:52 +0000]
PNP: add detail to debug resource dump

In the debug resource dump, decode the flags and indicate when
a resource is disabled or has been automatically assigned.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI: video: fix brightness allocation
Julia Jomantaite [Mon, 23 Jun 2008 21:50:42 +0000]
ACPI: video: fix brightness allocation

Fix use of uninitialized device->brightness.

Signed-off-by: Julia Jomantaite <julia.jomantaite@gmail.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

12 years agoACPI: Andi Kleen maintains the ACPI sub-system
Len Brown [Fri, 27 Jun 2008 15:31:50 +0000]
ACPI: Andi Kleen maintains the ACPI sub-system

...while Len is on sabbatical from Intel

Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI: Zhang Rui maintains ACPI THERMAL and FAN
Len Brown [Fri, 27 Jun 2008 15:22:46 +0000]
ACPI: Zhang Rui maintains ACPI THERMAL and FAN

Reflect that Zhang-Rui has been the sub-maintainer for
ACPI THERMAL and FAN for some time now.

Also, the Chinese custom is to speak family name first,
so rather than "Rui Zhang", write "Zhang Rui",
as he does on e-mail.

Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI: Disable MWAIT via DMI on broken Compal board
Zhao Yakui [Tue, 24 Jun 2008 10:02:57 +0000]
ACPI: Disable MWAIT via DMI on broken Compal board

If a system matches in this DMI table,
Linux will disable MWAIT support for idle.
ie. "idle=nomwait" is automatically invoked
and C1_FFH and C2C3_FFH access mode are disabled.

http://bugzilla.kernel.org/show_bug.cgi?id=10807
http://bugzilla.kernel.org/show_bug.cgi?id=10914

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI : Create "idle=nomwait" bootparam
Zhao Yakui [Tue, 24 Jun 2008 10:01:09 +0000]
ACPI : Create "idle=nomwait" bootparam

"idle=nomwait" disables the use of the MWAIT
instruction from both C1 (C1_FFH) and deeper (C2C3_FFH)
C-states.

When MWAIT is unavailable, the BIOS and OS generally
negotiate to use the HALT instruction for C1,
and use IO accesses for deeper C-states.

This option is useful for power and performance
comparisons, and also to work around BIOS bugs
where broken MWAIT support is advertised.

http://bugzilla.kernel.org/show_bug.cgi?id=10807
http://bugzilla.kernel.org/show_bug.cgi?id=10914

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI: Create "idle=halt" bootparam
Zhao Yakui [Tue, 24 Jun 2008 09:58:53 +0000]
ACPI: Create "idle=halt" bootparam

"idle=halt" limits the idle loop to using
the halt instruction.  No MWAIT, no IO accesses,
no C-states deeper than C1.

If something is broken in the idle code,
"idle=halt" is a less severe workaround
than "idle=poll" which disables all power savings.

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI: Disable the C2C3_FFH access mode HW has no MWAIT support
Zhao Yakui [Tue, 17 Jun 2008 06:39:59 +0000]
ACPI: Disable the C2C3_FFH access mode HW has no MWAIT support

991528d7348667924176f3e29addea0675298944
(ACPI: Processor native C-states using MWAIT)
started passing C2C3_FFH to _PDC to tell the BIOS
that Linux supports MWAIT for deep C-states.

However, we should first double check with the hardware
that it actually supports MWAIT before potentially exposing
a BIOS bug of an MWAIT _CST on HW that doesn't support MWAIT.

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI: Enhance /sys/firmware/interrupts to allow enable/disable/clear from user-space
Zhang Rui [Fri, 20 Jun 2008 01:42:47 +0000]
ACPI: Enhance /sys/firmware/interrupts to allow enable/disable/clear from user-space

Allow users to enable/disable/clear a specific & valid GPE/Fixed Event
in user space.

This is useful for debugging, especially for some
interrupt storm issues.

All wakeup GPEs are disabled and they can not be enabled at runtime,
and we mark them as invalid.

All GPEs that don't have a _Lxx/_Exx method are marked as invalid.

All Fixed Events that don't have an event handler are marked as invalid
and they can't be enabled until an event handler is registered.

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Ling Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Update version to 20080609
Bob Moore [Tue, 10 Jun 2008 06:37:53 +0000]
ACPICA: Update version to 20080609

Update version to 20080609.

Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Fix mutex debug code for wrong loop termination value
Bob Moore [Tue, 10 Jun 2008 06:30:04 +0000]
ACPICA: Fix mutex debug code for wrong loop termination value

Loop was terminating one iteration early, missing one of the
debugger handshake mutexes. Linn Crosetto.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Cleanup of _PRT parsing code
Bob Moore [Tue, 10 Jun 2008 06:27:55 +0000]
ACPICA: Cleanup of _PRT parsing code

Removed extraneous else clauses, other general cleanup.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Cleanup debug operand dump mechanism
Bob Moore [Tue, 10 Jun 2008 06:25:05 +0000]
ACPICA: Cleanup debug operand dump mechanism

Eliminated unnecessary operands; eliminated use of negative index
in loop.  Operands now displayed in correct order, not backwards.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Fix for invalid large array index on 64-bit systems
Bob Moore [Tue, 10 Jun 2008 06:21:05 +0000]
ACPICA: Fix for invalid large array index on 64-bit systems

This problem was introduced in 20080514 as a result of the
elimination of the acpi_native_uint type. Code uses a negative
array index, which should be eliminated.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Update disassembler for DMAR table changes
Bob Moore [Tue, 10 Jun 2008 06:19:32 +0000]
ACPICA: Update disassembler for DMAR table changes

Now supports the 2007 intel Virtualization Technology for Directed
I/O specification.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Update DMAR and SRAT table definitions
Bob Moore [Tue, 10 Jun 2008 07:54:40 +0000]
ACPICA: Update DMAR and SRAT table definitions

Synchronized tables with current specifications.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Workaround for reversed _PRT entries from BIOS
Bob Moore [Tue, 10 Jun 2008 06:16:47 +0000]
ACPICA: Workaround for reversed _PRT entries from BIOS

Some BIOSs erroneously reverse the _PRT SourceName and the
SourceIndex.  Detect and repair this problem. MS ACPI also allows
and repairs this problem, thus ACPICA must also.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Update version to 20080514
Bob Moore [Tue, 10 Jun 2008 06:15:05 +0000]
ACPICA: Update version to 20080514

Update version to 20080514

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Add const qualifier for appropriate string constants
Bob Moore [Tue, 10 Jun 2008 05:55:53 +0000]
ACPICA: Add const qualifier for appropriate string constants

Mostly MODULE_NAME and printf format strings.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Several lint changes, no functional changes
Bob Moore [Tue, 10 Jun 2008 05:44:48 +0000]
ACPICA: Several lint changes, no functional changes

Remove pointer cast warnings and fix for a debug printf.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Removed unused include files from source files
Bob Moore [Tue, 10 Jun 2008 05:43:34 +0000]
ACPICA: Removed unused include files from source files

From lint.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Eliminate acpi_native_uint type v2
Bob Moore [Tue, 10 Jun 2008 05:42:13 +0000]
ACPICA: Eliminate acpi_native_uint type v2

No longer needed; replaced mostly with u32, but also acpi_size
where a type that changes 32/64 bit on 32/64-bit platforms is
required.

v2: Fix a cast of a 32-bit int to a pointer in ACPI to avoid a compiler warning.
from David Howells

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Fix possible negative array index in acpi_ut_validate_exception
Bob Moore [Tue, 10 Jun 2008 04:53:01 +0000]
ACPICA: Fix possible negative array index in acpi_ut_validate_exception

Added NULL fields to the exception string arrays to eliminate
the -1 subtraction on the SubStatus field.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Update tracking macros to reduce code/data size
Jan Beulich [Tue, 10 Jun 2008 04:49:56 +0000]
ACPICA: Update tracking macros to reduce code/data size

Changed ACPI_MODULE_NAME and ACPI_FUNCTION_NAME to use arrays of
strings instead of pointers to static strings. Jan Beulich and
Bob Moore.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Fix for hang on GPE method invocation
Bob Moore [Tue, 10 Jun 2008 04:38:10 +0000]
ACPICA: Fix for hang on GPE method invocation

Fixes problem where the new method argument count validation mechanism
will enter an infinite loop when a GPE method is dispatched.
Problem fixed be removing the obsolete code that passes GPE block
information to the notify handler via the control method parameter pointer.

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: Add argument count checking to control method invocation via acpi_evaluate_object
Bob Moore [Tue, 10 Jun 2008 04:25:42 +0000]
ACPICA: Add argument count checking to control method invocation via acpi_evaluate_object

Error if too few arguments, warning if too many. This applies
only to external programmatic control method execution, not
method-to-method calls within the AML.

Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agofujitsu-laptop: depends on INPUT
Randy Dunlap [Fri, 27 Jun 2008 02:27:21 +0000]
fujitsu-laptop: depends on INPUT

fujitsu-laptop uses input_* functions, so it should depend on INPUT.

drivers/built-in.o: In function `acpi_fujitsu_add':
fujitsu-laptop.c:(.text+0xaaec7): undefined reference to `input_allocate_device'
fujitsu-laptop.c:(.text+0xaaf39): undefined reference to `input_register_device'
fujitsu-laptop.c:(.text+0xab025): undefined reference to `input_free_device'
drivers/built-in.o: In function `acpi_fujitsu_notify':
fujitsu-laptop.c:(.text+0xab0d8): undefined reference to `input_event'
fujitsu-laptop.c:(.text+0xab0e5): undefined reference to `input_event'
fujitsu-laptop.c:(.text+0xab0f5): undefined reference to `input_event'
fujitsu-laptop.c:(.text+0xab102): undefined reference to `input_event'
drivers/built-in.o: In function `acpi_fujitsu_hotkey_notify':
fujitsu-laptop.c:(.text+0xab261): undefined reference to `input_event'
drivers/built-in.o:fujitsu-laptop.c:(.text+0xab26e): more undefined references to `input_event' follow
drivers/built-in.o: In function `acpi_fujitsu_hotkey_add':
fujitsu-laptop.c:(.text+0xab49c): undefined reference to `input_allocate_device'
fujitsu-laptop.c:(.text+0xab51a): undefined reference to `input_register_device'
fujitsu-laptop.c:(.text+0xab5e4): undefined reference to `input_free_device'
make[1]: *** [.tmp_vmlinux1] Error 1

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>

12 years agosnapshot: Use pm_mutex for mutual exclusion
Rafael J. Wysocki [Wed, 11 Jun 2008 20:09:45 +0000]
snapshot: Use pm_mutex for mutual exclusion

We can avoid taking the BKL in snapshot_ioctl() if pm_mutex is used to prevent
the ioctls from being executed concurrently.

In addition, although it is only possible to open /dev/snapshot once, the task
which has done that may spawn a child that will inherit the open descriptor,
so in theory they can call snapshot_write(), snapshot_read() and
snapshot_release() concurrently.  pm_mutex can also be used for mutual
exclusion in such cases.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>

12 years agosnapshot: Push BKL down into ioctl handlers
Alan Cox [Wed, 11 Jun 2008 20:07:52 +0000]
snapshot: Push BKL down into ioctl handlers

Push BKL down into ioctl handlers - snapshot device.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoFreezer: Introduce PF_FREEZER_NOSIG
Rafael J. Wysocki [Wed, 11 Jun 2008 20:04:29 +0000]
Freezer: Introduce PF_FREEZER_NOSIG

The freezer currently attempts to distinguish kernel threads from
user space tasks by checking if their mm pointer is unset and it
does not send fake signals to kernel threads.  However, there are
kernel threads, mostly related to networking, that behave like
user space tasks and may want to be sent a fake signal to be frozen.

Introduce the new process flag PF_FREEZER_NOSIG that will be set
by default for all kernel threads and make the freezer only send
fake signals to the tasks having PF_FREEZER_NOSIG unset.  Provide
the set_freezable_with_signal() function to be called by the kernel
threads that want to be sent a fake signal for freezing.

This patch should not change the freezer's observable behavior.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>

12 years agoAPM emulation: Notify about all suspend events, not just APM invoked ones (v2)
Johannes Berg [Wed, 11 Jun 2008 20:03:10 +0000]
APM emulation: Notify about all suspend events, not just APM invoked ones (v2)

This revamps the apm-emulation code to get suspend notifications
regardless of what way pm_suspend() was invoked, whether via the
apm ioctl or via /sys/power/state. Also do some code cleanup and
add comments while at it.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI PM: Remove obsolete Toshiba workaround
Rafael J. Wysocki [Wed, 4 Jun 2008 23:17:28 +0000]
ACPI PM: Remove obsolete Toshiba workaround

Remove the obsolete workaround for a Toshiba Satellite 4030cdt
S1 problem from drivers/acpi/sleep/main.c .

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>

12 years agoPCI ACPI: Drop the second argument of platform_pci_choose_state
Rafael J. Wysocki [Wed, 4 Jun 2008 23:16:37 +0000]
PCI ACPI: Drop the second argument of platform_pci_choose_state

Since the second argument of acpi_pci_choose_state() and
platform_pci_choose_state() is never used, remove it.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>

12 years agoACPI PM: acpi_pm_device_sleep_state() cleanup
David Brownell [Wed, 4 Jun 2008 23:15:40 +0000]
ACPI PM: acpi_pm_device_sleep_state() cleanup

Get rid of a superfluous acpi_pm_device_sleep_state() parameter.  The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do.  (However, this
does not address the fact that ACPI still doesn't set up those flags.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>

12 years agodock: bay: Don't call acpi_walk_namespace() when ACPI is disabled.
Len Brown [Wed, 25 Jun 2008 02:57:12 +0000]
dock: bay: Don't call acpi_walk_namespace() when ACPI is disabled.

Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI: don't walk tables if ACPI was disabled
Vegard Nossum [Fri, 20 Jun 2008 13:39:09 +0000]
ACPI: don't walk tables if ACPI was disabled

Ingo Molnar wrote:
> -tip auto-testing started triggering this spinlock corruption message
> yesterday:
>
> [    3.976213] calling  acpi_rtc_init+0x0/0xd3
> [    3.980213] ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread F7C50000 could not acquire Mutex [3] [20080321]
> [    3.992213] BUG: spinlock bad magic on CPU#0, swapper/1
> [    3.992213]  lock: c2508dc4, .magic: 00000000, .owner: swapper/1, .owner_cpu: 0

This is apparently because some parts of ACPI, including mutexes, are not
initialized when acpi=off is passed to the kernel.

Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoacer-wmi: Remove version number
Carlos Corbacho [Sat, 21 Jun 2008 08:09:58 +0000]
acer-wmi: Remove version number

It doesn't make much sense these days.

Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoacer-wmi: Add debugfs file for device detection
Carlos Corbacho [Sat, 21 Jun 2008 08:09:53 +0000]
acer-wmi: Add debugfs file for device detection

Add a debugfs file for showing the full results of the method we use to
detect devices on WMID laptops.

This should be useful in the case that a Linux user gets an Acer laptop
with 3G support (and/ or people who enjoy ripping their wireless cards out)
so we can get some feedback on how this value changes in these cases.

(At the moment, we always enable the wireless and 3G control. In the case
of the former, this is fairly safe. In the case of the latter though,
trying to toggle this device if it doesn't exist on a laptop causes ACPI
warnings/ errors).

To summarise: If you have an Acer laptop with a built in 3G card, please
report back the value from this file.

Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoacer-wmi: Disable device autodetection on Fujitsu Siemens Amilo Li2732
Carlos Corbacho [Sat, 21 Jun 2008 08:09:48 +0000]
acer-wmi: Disable device autodetection on Fujitsu Siemens Amilo Li2732

The AMW0 (V1) device detection method doesn't work properly on this laptop,
so disable it, and for other laptops that may have this problem, by
switching on a strange GUID.

Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoacer-wmi: Add EC quirk for Fujitsu Siemens Amilo Li 1718
Carlos Corbacho [Sat, 21 Jun 2008 08:09:38 +0000]
acer-wmi: Add EC quirk for Fujitsu Siemens Amilo Li 1718

This laptop needs a different EC quirk from the standard Acer one to read
the wireless status.

Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoacer-wmi: Respect framebuffer blanking in backlight
Carlos Corbacho [Sat, 21 Jun 2008 08:09:27 +0000]
acer-wmi: Respect framebuffer blanking in backlight

If the framebuffer has requested blanking, turn the backlight down. Also
offer the user the option to do this.

Reported-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoacer-wmi: Blacklist backlight on Acer Aspire 1520 & 1360 series
Carlos Corbacho [Sat, 21 Jun 2008 08:09:22 +0000]
acer-wmi: Blacklist backlight on Acer Aspire 1520 & 1360 series

A newer BIOS for these laptops adds ACPI-WMI support to them. However, it does
not add support for the backlight via the EC, and we have no way to detect
this on older machines, so blacklist it from them.

Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoacer-wmi: Remove LED colour comment from documentation
Carlos Corbacho [Sat, 21 Jun 2008 08:09:08 +0000]
acer-wmi: Remove LED colour comment from documentation

This should have been removed when the colour was removed from the LED
device name.

Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoeeepc-laptop: static
Adrian Bunk [Wed, 25 Jun 2008 16:25:47 +0000]
eeepc-laptop: static

make the needlessly global cm_{g,s}etv[] static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPICA: fix mutex names in debug code.
Vegard Nossum [Fri, 20 Jun 2008 11:56:56 +0000]
ACPICA: fix mutex names in debug code.

Reorder the mutex names to match the preceding #defines

Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoMake GPE disable more robust
Bob Moore [Fri, 13 Jun 2008 00:28:55 +0000]
Make GPE disable more robust

Implemented another change for the GPE disable. We now perform a
read-change-write of the enable register instead of simply writing out the
cached enable mask. This will prevent inadvertent enabling of GPEs if a rogue
GPE is received during initialization (before GPE handlers are installed.)

http://bugzilla.kernel.org/show_bug.cgi?id=6217

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agocompal-laptop: remove unnecessary lcd_level attribute
Cezary Jackiewicz [Thu, 12 Jun 2008 20:08:59 +0000]
compal-laptop: remove unnecessary lcd_level attribute

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoacpi: fix printk format warning
Randy Dunlap [Tue, 17 Jun 2008 16:43:41 +0000]
acpi: fix printk format warning

Fix printk format warning:

linux-next-20080617/drivers/acpi/processor_throttling.c:1258: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI: fix processor throttling set error
Yi Yang [Sat, 14 Jun 2008 04:54:37 +0000]
ACPI: fix processor throttling set error

http://bugzilla.kernel.org/show_bug.cgi?id=9704

When echo some invalid values to /proc/acpi/processor/*/throttling,
there isn't any error info returned, on the contray, it sets
throttling value to some T* successfully, obviously, this is incorrect,
a correct way should be to let it fail and return error info.

This patch fixed the aforementioned issue, it also enables
/proc/acpi/processor/*/throttling to accept such values as 't0' and 'T0',
it also strictly limits /proc/acpi/processor/*/throttling only to accept
 "*", "t*" and "T*", "*" is the throttling state value the processor can
support, current, it is 0 - 7.

Before applying this patch, the test result is below:

[root@localhost acpi]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T1
state available: T0 to T7
states:
    T0:                  100%
   *T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost acpi]# echo "1xxxxxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost acpi]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T1
state available: T0 to T7
states:
    T0:                  100%
   *T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost acpi]# echo "0" > /proc/acpi/processor/CPU0/throttling
[root@localhost acpi]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost acpi]# cd /
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "T0" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "T7" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "T100" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "xxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "2xxxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T2
state available: T0 to T7
states:
    T0:                  100%
    T1:                  87%
   *T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost /]# echo "7777" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost /]# echo "7xxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T7
state available: T0 to T7
states:
    T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
   *T7:                  12%
[root@localhost /]#

After applying this patch, the test result is below:

[root@localhost linux-2.6.24-rc6]# echo > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "0" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo "t0" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo "T0" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T0
state available: T0 to T7
states:
   *T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
    T7:                  12%
[root@localhost linux-2.6.24-rc6]# echo "T7" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T7
state available: T0 to T7
states:
    T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
   *T7:                  12%
[root@localhost linux-2.6.24-rc6]# echo "T8" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# vi drivers/acpi/processor_throttling.c
[root@localhost linux-2.6.24-rc6]# echo "T8" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "t7" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo "t70" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "70" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "7000" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "70" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo "xxx" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo -n > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo -n "" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo $?
0
[root@localhost linux-2.6.24-rc6]# echo -n "" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T7
state available: T0 to T7
states:
    T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
   *T7:                  12%
[root@localhost linux-2.6.24-rc6]# echo -n "" > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# cat /proc/acpi/processor/CPU0/throttling
state count:             8
active state:            T7
state available: T0 to T7
states:
    T0:                  100%
    T1:                  87%
    T2:                  75%
    T3:                  62%
    T4:                  50%
    T5:                  37%
    T6:                  25%
   *T7:                  12%
[root@localhost linux-2.6.24-rc6]# echo t0 > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo T0 > /proc/acpi/processor/CPU0/throttling
[root@localhost linux-2.6.24-rc6]# echo Tt0 > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]# echo T > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost linux-2.6.24-rc6]#

Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI: fix acpi fan state set error
Yi Yang [Sat, 14 Jun 2008 04:52:06 +0000]
ACPI: fix acpi fan state set error

Under /proc/acpi, there is a fan control interface, a user can
set 0 or 3 to /proc/acpi/fan/*/state, 0 denotes D0 state, 3
denotes D3 state, but in current implementation, a user can
set a fan to D1 state by any char excluding '1', '2' and '3'.

For example:

[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost acpi]# echo "3" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "xxxxx" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  on

Obviously, such inputs as "" and "xxxxx" are invalid for fan state.

This patch fixes this issue, it strictly limits fan state only to
accept 0, 1, 2 and 3, any other inputs are invalid.

Before applying this patch, the test result is:

[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost acpi]# echo "3" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "xxxxx" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost acpi]# echo "3" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "3x" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost acpi]# echo "-1x" > /proc/acpi/fan/C31B/state
[root@localhost acpi]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost acpi]#

After applying this patch, the test result is:

[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "" > /proc/acpi/fan/C31B/state
-bash: echo: write error: Invalid argument
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "3" > /proc/acpi/fan/C31B/state
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "xxxxx" > /proc/acpi/fan/C31B/state
-bash: echo: write error: Invalid argument
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "-1x" > /proc/acpi/fan/C31B/state
-bash: echo: write error: Invalid argument
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "0" > //proc/acpi/fan/C31B/state
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost ~]# echo "4" > //proc/acpi/fan/C31B/state
-bash: echo: write error: Invalid argument
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost ~]# echo "3" > //proc/acpi/fan/C31B/state
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  off
[root@localhost ~]# echo "0" > //proc/acpi/fan/C31B/state
[root@localhost ~]# cat /proc/acpi/fan/C31B/state
status:                  on
[root@localhost ~]# echo "3x" > //proc/acpi/fan/C31B/state
-bash: echo: write error: Invalid argument
[root@localhost ~]#

Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

12 years agoACPI: fix checkpatch.pl complaints in scan.c
Alok N Kataria [Fri, 13 Jun 2008 16:54:24 +0000]
ACPI: fix checkpatch.pl complaints in scan.c

http://bugzilla.kernel.org/show_bug.cgi?id=9772

Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoFujitsu-laptop update
Jonathan Woithe [Wed, 11 Jun 2008 00:44:56 +0000]
Fujitsu-laptop update

Add additional capabilities to the Fujitsu-laptop driver.

 * Brightness hotkey actions are sent to userspace. This can be disabled
   using a module parameter if it causes issues with models which handle
   these keys transparently in the BIOS.

 * Actions of additional hotkeys found on some Fujitsu models (eg: the
   suspend key and the dedicated "power on passphrase" keys) are broadcast
   to userspace.

 * An alternative brightness control method used by some Fujitsu models
   (for example, the S6410) is now supported, enabling software brightness
   controls on models using this method.

 * DMI-based module aliases are configured for the S6410 and S7020.

 * The current LCD brightness after booting should now be reflected in the
   standard backlight interface sysfs file (previously it was always set to
   0).  The platform brightness sysfs interface has always been fine.

Thanks go to Peter Gruber who provided a significant portion of this code
and tested various iterations of the patch on his S6410.

Signed-off-by: Peter Gruber <nokos@gmx.net>
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoACPI: change processors from array to per_cpu variable
Mike Travis [Mon, 9 Jun 2008 23:22:23 +0000]
ACPI: change processors from array to per_cpu variable

Change processors from an array sized by NR_CPUS to a per_cpu variable.

Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agomisc,acpi,backlight: compal Laptop Extras
Cezary Jackiewicz [Mon, 9 Jun 2008 23:22:22 +0000]
misc,acpi,backlight: compal Laptop Extras

This is driver for Compal Laptop: FL90/IFL90, based on MSI driver.

This driver exports a few files in /sys/devices/platform/compal-laptop/:
 lcd_level - screen brightness: contains a single integer in the range 0..7 (rw)
 wlan - wlan subsystem state: contains 0 or 1 (rw)
 bluetooth - bluetooth subsystem state: contains 0 or 1 (rw)
 raw - raw value taken from embedded controller register (ro)

In addition to these platform device attributes the driver registers itself
in the Linux backlight control subsystem and is available to userspace under
/sys/class/backlight/compal-laptop/.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Len Brown <lenb@kernel.org>
Cc: Alexey Starikovskiy <aystarik@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>

12 years agocreate sysfs link from acpi device to sysdev for cpu
Zhang Rui [Tue, 29 Apr 2008 06:36:07 +0000]
create sysfs link from acpi device to sysdev for cpu

Sys I/F under acpi device node and sysdev device node are both
needed for cpu hot-removal. User space need this link so that
they know they are poking the sys I/F for the same cpu.
http://bugzilla.kernel.org/show_bug.cgi?id=9772

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoforce offline the processor during hot-removal
Zhang Rui [Tue, 29 Apr 2008 06:35:56 +0000]
force offline the processor during hot-removal

The ACPI device node for the cpu has already been unregistered
when acpi_processor_handle_eject is called.
Thus we should offline the cpu and continue, rather than a failure here.
http://bugzilla.kernel.org/show_bug.cgi?id=9772

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agofix a deadlock issue when poking "eject" file
Zhang Rui [Tue, 29 Apr 2008 06:35:48 +0000]
fix a deadlock issue when poking "eject" file

"/sys/devices/LNXSYSTM:00/.../eject" is used to evaluate _EJx method
and eject a device in user space.
But system hangs when poking the "eject" file because that
the device hot-removal code invoke the driver .remove method which will
try to remove the "eject" file as a result.

Queues the hot-removal function for deferred execution in this patch.
http://bugzilla.kernel.org/show_bug.cgi?id=9772

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>

12 years agoMerge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
Linus Torvalds [Wed, 16 Jul 2008 18:47:35 +0000]
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (44 commits)
  hwmon: (w83l786ng) Convert to a new-style i2c driver
  hwmon: (w83l785ts) Convert to a new-style i2c driver
  hwmon: (w83793) Convert to a new-style i2c driver
  hwmon: (w83792d) Convert to a new-style i2c driver
  hwmon: (w83791d) Convert to a new-style i2c driver
  hwmon: (thmc50) Convert to a new-style i2c driver
  hwmon: (smsc47m192) Convert to a new-style i2c driver
  hwmon: (max6650) Convert to a new-style i2c driver
  hwmon: (max1619) Convert to a new-style i2c driver
  hwmon: (lm93) Convert to a new-style i2c driver
  hwmon: (lm92) Convert to a new-style i2c driver
  hwmon: (lm90) Convert to a new-style i2c driver
  hwmon: (lm87) Convert to a new-style i2c driver
  hwmon: (lm83) Convert to a new-style i2c driver
  hwmon: (lm80) Convert to a new-style i2c driver
  hwmon: (lm77) Convert to a new-style i2c driver
  hwmon: (lm63) Convert to a new-style i2c driver
  hwmon: (gl520sm) Convert to a new-style i2c driver
  hwmon: (gl518sm) Convert to a new-style i2c driver
  hwmon: (fscpos) Convert to a new-style i2c driver
  ...

12 years agoFix compile issues in fs/compat_ioctl.c when CONFIG_BLOCK is disabled
Randy Dunlap [Wed, 16 Jul 2008 13:52:00 +0000]
Fix compile issues in fs/compat_ioctl.c when CONFIG_BLOCK is disabled

Fix fs/compat_ioctl.c to handle CONFIG_BLOCK=n, CONFIG_SCSI=n to avoid
build errors:

In file included from include/scsi/scsi.h:12,
                 from fs/compat_ioctl.c:71:
include/scsi/scsi_cmnd.h:27:25: warning: "BLK_MAX_CDB" is not defined
include/scsi/scsi_cmnd.h:28:3: error: #error MAX_COMMAND_SIZE can not be bigger than BLK_MAX_CDB
In file included from include/scsi/scsi.h:12,
                 from fs/compat_ioctl.c:71:
include/scsi/scsi_cmnd.h: In function 'scsi_bidi_cmnd':
include/scsi/scsi_cmnd.h:182: error: implicit declaration of function 'blk_bidi_rq'
include/scsi/scsi_cmnd.h:183: error: dereferencing pointer to incomplete type
include/scsi/scsi_cmnd.h: In function 'scsi_in':
include/scsi/scsi_cmnd.h:189: error: dereferencing pointer to incomplete type

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

12 years agopowerpc/ep8248e: Fix compile problem if !CONFIG_FS_ENET
Kumar Gala [Wed, 16 Jul 2008 13:39:12 +0000]
powerpc/ep8248e: Fix compile problem if !CONFIG_FS_ENET

If we don't enable FS_ENET we get build issues:

arch/powerpc/platforms/built-in.o: In function `ep8248e_mdio_probe':
arch/powerpc/platforms/82xx/ep8248e.c:129: undefined reference to `alloc_mdio_bitbang'
arch/powerpc/platforms/82xx/ep8248e.c:143: undefined reference to `mdiobus_register'

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

12 years agoFix MIPS cross-compile problem
Ralf Baechle [Wed, 16 Jul 2008 12:02:24 +0000]
Fix MIPS cross-compile problem

Crosscompiling on a Fedora 9 machine running gcc 4.3.0 as its host compiler
and gcc 3.4.6 for the mips-linux target results in the following build
error:

$ make malta_defconfig
$ make
cc1: error: unrecognized command line option "-fno-stack-protector"
scripts/kconfig/conf -s arch/mips/Kconfig
cc1: error: unrecognized command line option "-fno-stack-protector"

The arch Makefile is included too late so the host compiler is feature
tested, not the crosscompiler as intended and thus the Makefile applies
adds -fno-stack-protector to crosscompiler's flags which fails for gcc
3.4.6.  The bug was introduced by e06b8b98da071f7dd78fb7822991694288047df0
in 2.6.25; 35bb5b1e0e84cfa1a8906f7e6a77f391ff315791 did add more flags
testing before the arch Makefile inclusion.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

12 years agohwmon: (w83l786ng) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:18 +0000]
hwmon: (w83l786ng) Convert to a new-style i2c driver

The new-style w83l786ng driver implements the optional detect()
callback to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Kevin Lo <kevlo@kevlo.org>

12 years agohwmon: (w83l785ts) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:18 +0000]
hwmon: (w83l785ts) Convert to a new-style i2c driver

The new-style w83l785ts driver implements the optional detect()
callback to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (w83793) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:17 +0000]
hwmon: (w83793) Convert to a new-style i2c driver

The new-style w83793 driver implements the optional detect()
callback to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (w83792d) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:17 +0000]
hwmon: (w83792d) Convert to a new-style i2c driver

The new-style w83792d driver implements the optional detect()
callback to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (w83791d) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:17 +0000]
hwmon: (w83791d) Convert to a new-style i2c driver

The new-style w83791d driver implements the optional detect()
callback to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>

12 years agohwmon: (thmc50) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:16 +0000]
hwmon: (thmc50) Convert to a new-style i2c driver

The new-style thmc50 driver implements the optional detect()
callback to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>

12 years agohwmon: (smsc47m192) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:16 +0000]
hwmon: (smsc47m192) Convert to a new-style i2c driver

The new-style smsc47m192 driver implements the optional detect()
callback to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hartmut Rick <linux@rick.claranet.de>

12 years agohwmon: (max6650) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:16 +0000]
hwmon: (max6650) Convert to a new-style i2c driver

The new-style max6650 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans J. Koch <hjk@linutronix.de>

12 years agohwmon: (max1619) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:15 +0000]
hwmon: (max1619) Convert to a new-style i2c driver

The new-style max1619 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alexey Fisher <fishor@mail.ru>

12 years agohwmon: (lm93) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:15 +0000]
hwmon: (lm93) Convert to a new-style i2c driver

The new-style lm93 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Eric J. Bowersox <ericb@aspsys.com>
Cc: Carsten Emde <cbe@osadl.org>
Cc: Hans J. Koch <hjk@linutronix.de>

12 years agohwmon: (lm92) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:15 +0000]
hwmon: (lm92) Convert to a new-style i2c driver

The new-style lm92 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm90) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:15 +0000]
hwmon: (lm90) Convert to a new-style i2c driver

The new-style lm90 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm87) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:14 +0000]
hwmon: (lm87) Convert to a new-style i2c driver

The new-style lm87 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>

12 years agohwmon: (lm83) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:14 +0000]
hwmon: (lm83) Convert to a new-style i2c driver

The new-style lm83 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm80) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:14 +0000]
hwmon: (lm80) Convert to a new-style i2c driver

The new-style lm80 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm77) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:13 +0000]
hwmon: (lm77) Convert to a new-style i2c driver

The new-style lm77 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andras Bali <drewie@freemail.hu>

12 years agohwmon: (lm63) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:13 +0000]
hwmon: (lm63) Convert to a new-style i2c driver

The new-style lm63 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (gl520sm) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:13 +0000]
hwmon: (gl520sm) Convert to a new-style i2c driver

The new-style gl520sm driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Maarten Deprez <maartendeprez@users.sourceforge.net>

12 years agohwmon: (gl518sm) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:13 +0000]
hwmon: (gl518sm) Convert to a new-style i2c driver

The new-style gl518sm driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (fscpos) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:12 +0000]
hwmon: (fscpos) Convert to a new-style i2c driver

The new-style fscpos driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (fschmd) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:12 +0000]
hwmon: (fschmd) Convert to a new-style i2c driver

The new-style fschmd driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <j.w.r.degoede@hhs.nl>

12 years agohwmon: (fscher) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:12 +0000]
hwmon: (fscher) Convert to a new-style i2c driver

The new-style fscher driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Reinhard Nissl <rnissl@gmx.de>

12 years agohwmon: (f75375s) Drop legacy i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:11 +0000]
hwmon: (f75375s) Drop legacy i2c driver

Drop the legacy f75375s i2c driver, and add a detect callback to the
new-style i2c driver to achieve the same functionality.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Riku Voipio <riku.voipio@movial.fi>

12 years agohwmon: (ds1621) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:11 +0000]
hwmon: (ds1621) Convert to a new-style i2c driver

The new-style ds1621 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (atxp1) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:11 +0000]
hwmon: (atxp1) Convert to a new-style i2c driver

The new-style atxp1 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (asb100) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:11 +0000]
hwmon: (asb100) Convert to a new-style i2c driver

The new-style asb100 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (adt7473) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:10 +0000]
hwmon: (adt7473) Convert to a new-style i2c driver

The new-style adt7473 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>

12 years agohwmon: (adt7470) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:10 +0000]
hwmon: (adt7470) Convert to a new-style i2c driver

The new-style adt7470 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>

12 years agohwmon: (ads7828) Convert to a new-style i2c driver
Jean Delvare [Wed, 16 Jul 2008 17:30:10 +0000]
hwmon: (ads7828) Convert to a new-style i2c driver

The new-style ads7828 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>