11 years agosh: mach-ecovec24: Remove un-defined settings for VPU
Kuninori Morimoto [Wed, 2 Dec 2009 09:36:18 +0000]
sh: mach-ecovec24: Remove un-defined settings for VPU

The setting of VPU need not be changed from default.
And current setting value is not defined on SH7724

Reported-by:   Goda Yusuke <goda.yusuke@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: mach-ecovec24: LCDC drive ability become high
Kuninori Morimoto [Wed, 2 Dec 2009 09:35:42 +0000]
sh: mach-ecovec24: LCDC drive ability become high

Drive ability for LCDC become high for safety,
became there is strange individual specificity board in mass production

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: fix sh7724 VEU3F resource size
Magnus Damm [Tue, 1 Dec 2009 13:38:52 +0000]
sh: fix sh7724 VEU3F resource size

Fix one-off VEU3F size error for sh7724.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agoserial: sh-sci: Fix too early port disabling.
Guennadi Liakhovetski [Tue, 1 Dec 2009 09:54:46 +0000]
serial: sh-sci: Fix too early port disabling.

Currently serial ports on SH CPUs get disabled too early, because the
sci_tx_empty() routine claims to not be able to detect whether the
transmission has been completed and just always returns TIOCSER_TEMT. This
results in corrupt output of last characters if the port is not open for
reading at the same time. It is however possible to detect whether
transmission has been completed. Use the TEND bit of the status register
for this.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: pfc: pr_info() -> pr_debug() cleanups.
Paul Mundt [Mon, 30 Nov 2009 03:15:04 +0000]
sh: pfc: pr_info() -> pr_debug() cleanups.

For some reason this was using pr_info() nested under an ifdef DEBUG.
While this is appealing in that it circumvents the effort necessary to
change ones loglevel, it's not terribly practical. So, convert it over
to pr_debug().

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
Paul Mundt [Mon, 30 Nov 2009 03:10:41 +0000]
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.

Now that the PFC code is exposed for other architectures, use the common
__raw_xxx() routines instead of the ctrl_xxx() ones. This will be needed
for ARM-based SH-Mobiles amongst others.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Improve kfr2r09 serial port setup code
Magnus Damm [Fri, 27 Nov 2009 09:28:03 +0000]
sh: Improve kfr2r09 serial port setup code

This patch improves the serial port communication quality
of port YC401 on the KFR2R09 board. With this fix serial
console is fine at 115200 - up and down keys now work as
expected. Thanks to Hirohide Yamasaki for this fix.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Break out SuperH PFC code
Magnus Damm [Fri, 27 Nov 2009 07:38:01 +0000]
sh: Break out SuperH PFC code

This file breaks out the SuperH PFC code from
arch/sh/kernel/gpio.c + arch/sh/include/asm/gpio.h
to drivers/sh/pfc.c + include/linux/sh_pfc.h.

Similar to the INTC stuff. The non-SuperH specific
file location makes it possible to share the code
between multiple architectures.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Move KEYSC header file
Magnus Damm [Fri, 27 Nov 2009 07:32:24 +0000]
sh: Move KEYSC header file

This patch moves the KEYSC header file from the
SuperH specific asm directory to a place where
it can be shared by multiple architectures.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
Alexey Dobriyan [Fri, 27 Nov 2009 06:42:16 +0000]
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Add CPG save/restore code for sh7724 R-standby
Magnus Damm [Fri, 27 Nov 2009 05:16:21 +0000]
sh: Add CPG save/restore code for sh7724 R-standby

Add sh7724 code to save and restore CPG state during
R-standby. Only CPG registers IRDACLKCR and SPUCLKCR
require software save and restore.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Add SDHI power control support to Ecovec
Magnus Damm [Fri, 27 Nov 2009 04:36:58 +0000]
sh: Add SDHI power control support to Ecovec

This patch adds support for SDHI power control to the
Ecovec board. Platform data and power control callbacks
for SDHI0 and SDHI1 are added. Power is by default off.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agomfd: Add power control platform data to SDHI driver
Magnus Damm [Fri, 27 Nov 2009 04:31:27 +0000]
mfd: Add power control platform data to SDHI driver

This patch adds platform data with a function for power
control to the SDHI driver. The idea is that board specific
code can provide their own functions so power can be enabled
and disabled for the sd-cards.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: mach-ecovec24: modify address map
Kuninori Morimoto [Thu, 26 Nov 2009 06:00:29 +0000]
sh: mach-ecovec24: modify address map

ecovec24 board expect address map 2 instead of map 1

Signed-off-by: Mizukawa Tatsuo <mizukawa.tatsuo@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agoserial: sh-sci: Depend on HAVE_CLK unconditionally.
Paul Mundt [Wed, 25 Nov 2009 07:23:35 +0000]
serial: sh-sci: Depend on HAVE_CLK unconditionally.

The sh-sci code conditionalized the clock framework support in order to
give the other platforms a chance to catch up. sh64 supported this some
time ago and the forthcoming ARM changes handle this as well, this leaves
h8300 as the odd one out. H8300 has had since 2.5 to merge it's sh-sci
support upstream, and has yet to do so. At this point I will no longer be
holding back the driver to support an unreponsive architecture, 7 years
is quite enough of a grace period. Support is easily implemented on the
architecture if and when it ever decides to merge its changes upstream.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Fix up the FPU emulation build.
Paul Mundt [Wed, 25 Nov 2009 03:07:31 +0000]
sh: Fix up the FPU emulation build.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agoserial: sh-sci: don't use __devexit_p to wrap sci_remove
Uwe Kleine-König [Tue, 24 Nov 2009 21:07:32 +0000]
serial: sh-sci: don't use __devexit_p to wrap sci_remove

The function sci_remove is defined without any section modifier, so
don't use __devexit_p to wrap it.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Magnus Damm <damm@opensource.se>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agortc: don't use __exit_p to wrap ds1302_rtc_remove
Uwe Kleine-König [Tue, 24 Nov 2009 21:07:23 +0000]
rtc: don't use __exit_p to wrap ds1302_rtc_remove

The function ds1302_rtc_remove is defined using __devexit, so don't use
__exit_p but __devexit_p to wrap it.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: linux-kernel@vger.kernel.org
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Apply the sleazy FPU changes for SH-2A FPU as well.
Paul Mundt [Tue, 24 Nov 2009 08:56:17 +0000]
sh: Apply the sleazy FPU changes for SH-2A FPU as well.

This plugs in the fpu_counter manipulation for the SH-2A side also.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Minor optimisations to FPU handling
Stuart Menefy [Fri, 25 Sep 2009 17:25:10 +0000]
sh: Minor optimisations to FPU handling

A number of small optimisations to FPU handling, in particular:

 - move the task USEDFPU flag from the thread_info flags field (which
   is accessed asynchronously to the thread) to a new status field,
   which is only accessed by the thread itself. This allows locking to
   be removed in most cases, or can be reduced to a preempt_lock().
   This mimics the i386 behaviour.

 - move the modification of regs->sr and thread_info->status flags out
   of save_fpu() to __unlazy_fpu(). This gives the compiler a better
   chance to optimise things, as well as making save_fpu() symmetrical
   with restore_fpu() and init_fpu().

 - implement prepare_to_copy(), so that when creating a thread, we can
   unlazy the FPU prior to copying the thread data structures.

Also make sure that the FPU is disabled while in the kernel, in
particular while booting, and for newly created kernel threads,

In a very artificial benchmark, the execution time for 2500000
context switches was reduced from 50 to 45 seconds.

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Improve performance of SH4 versions of copy/clear_user_highpage
Stuart Menefy [Tue, 27 Oct 2009 15:14:06 +0000]
sh: Improve performance of SH4 versions of copy/clear_user_highpage

The previous implementation of clear_user_highpage and copy_user_highpage
checked to see if there was a D-cache aliasing issue between the user
and kernel mappings of a page, but if there was they always did a
flush with writeback on the dirtied kernel alias.

However as we now have the ability to map a page into kernel space
with the same cache colour as the user mapping, there is no need to
write back this data.

Currently we also invalidate the kernel alias as a precaution, however
I'm not sure if this is actually required.

Also correct the definition of FIX_CMAP_END so that the mappings created
by kmap_coherent() are actually at the correct colour.

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agoMerge branch 'master' into sh/st-integration
Paul Mundt [Tue, 24 Nov 2009 07:32:11 +0000]
Merge branch 'master' into sh/st-integration

11 years agosh: Optimised memset for SH4
Stuart Menefy [Tue, 27 Oct 2009 15:14:06 +0000]
sh: Optimised memset for SH4

Optimised version of memset for the SH4 which uses movca.l.

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: add sleazy FPU optimization
Giuseppe CAVALLARO [Tue, 7 Jul 2009 14:25:10 +0000]
sh: add sleazy FPU optimization

sh port of the sLeAZY-fpu feature currently implemented for some architectures
such us i386.

Right now the SH kernel has a 100% lazy fpu behaviour.
This is of course great for applications that have very sporadic or no FPU use.
However for very frequent FPU users...  you take an extra trap every context
The patch below adds a simple heuristic to this code: after 5 consecutive
context switches of FPU use, the lazy behavior is disabled and the context
gets restored every context switch.
After 256 switches, this is reset and the 100% lazy behavior is returned.

Tests with LMbench showed no regression.
I saw a little improvement due to the prefetching (~2%).

The tests below also show that, with this sLeazy patch, indeed,
the number of FPU exceptions is reduced.
To test this. I hacked the lat_ctx LMBench to use the FPU a little more.

   sLeasy implementation
   switch_to calls            |  79326
   sleasy   calls             |  42577
   do_fpu_state_restore  calls|  59232
   restore_fpu   calls        |  59032

   Exceptions:  0x800 (FPU disabled  ): 16604

   100% Leazy (default implementation)
   switch_to  calls            |  79690
   do_fpu_state_restore calls  |  53299
   restore_fpu  calls          |   53101

   Exceptions: 0x800 (FPU disabled  ):  53273

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agoMerge branch 'i2c-pnx-fixes' of git://git.fluff.org/bjdooks/linux
Linus Torvalds [Fri, 20 Nov 2009 04:29:34 +0000]
Merge branch 'i2c-pnx-fixes' of git://git.fluff.org/bjdooks/linux

* 'i2c-pnx-fixes' of git://git.fluff.org/bjdooks/linux:
  i2c: i2c-pnx: Added missing mach/i2c.h and linux/io.h header file includes
  i2c: i2c-pnx: Made buf type unsigned to prevent sign extension
  i2c: i2c-pnx: Limit minimum jiffie timeout to 2

11 years agoMerge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec...
Linus Torvalds [Fri, 20 Nov 2009 04:29:05 +0000]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jlbec/ocfs2

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  ocfs2: Trivial cleanup of jbd compatibility layer removal
  ocfs2: Refresh documentation
  ocfs2: return f_fsid info in ocfs2_statfs()
  ocfs2: duplicate inline data properly during reflink.
  ocfs2: Move ocfs2_complete_reflink to the right place.
  ocfs2: Return -EINVAL when a device is not ocfs2.

11 years agoi2c: i2c-pnx: Added missing mach/i2c.h and linux/io.h header file includes
Kevin Wells [Wed, 11 Nov 2009 23:25:52 +0000]
i2c: i2c-pnx: Added missing mach/i2c.h and linux/io.h header file includes

Added missing mach/i2c.h and linux/io.h header file includes

Signed-off-by: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

11 years agoi2c: i2c-pnx: Made buf type unsigned to prevent sign extension
Kevin Wells [Wed, 11 Nov 2009 23:23:00 +0000]
i2c: i2c-pnx: Made buf type unsigned to prevent sign extension

Made buf type unsigned to prevent sign extension

Signed-off-by: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

11 years agoi2c: i2c-pnx: Limit minimum jiffie timeout to 2
Kevin Wells [Wed, 11 Nov 2009 23:28:13 +0000]
i2c: i2c-pnx: Limit minimum jiffie timeout to 2

Limit minimum jiffie timeout to 2 to prevent early timeout on systems
with low tick rates

Signed-off-by: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

11 years agoLinux 2.6.32-rc8
Linus Torvalds [Thu, 19 Nov 2009 22:32:38 +0000]
Linux 2.6.32-rc8

11 years agoMerge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
Linus Torvalds [Thu, 19 Nov 2009 21:43:19 +0000]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  SUNRPC: Address buffer overrun in rpc_uaddr2sockaddr()
  NFSv4: Fix a cache validation bug which causes getcwd() to return ENOENT

11 years agovt: Fix use of "new" in a struct field
Alan Cox [Thu, 19 Nov 2009 13:30:36 +0000]
vt: Fix use of "new" in a struct field

As this struct is exposed to user space and the API was added for this
release it's a bit of a pain for the C++ world and we still have time to
fix it. Rename the fields before we end up with that pain in an actual

Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Olivier Goffart
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoFix handling of the HP/Acer 'DMAR at zero' BIOS error for machines with <4GiB RAM.
David Woodhouse [Thu, 19 Nov 2009 02:18:44 +0000]
Fix handling of the HP/Acer 'DMAR at zero' BIOS error for machines with <4GiB RAM.

Commit 86cf898e1d0fca245173980e3897580db38569a8 ("intel-iommu: Check for
'DMAR at zero' BIOS error earlier.") was supposed to work by pretending
not to detect an IOMMU if it was actually being reported by the BIOS at
physical address zero.

However, the intel_iommu_init() function is called unconditionally, as
are the corresponding functions for other IOMMU hardware.

So the patch only worked if you have RAM above the 4GiB boundary. It
caused swiotlb to be initialised when no IOMMU was detected during early
boot, and thus the later IOMMU init would refuse to run.

But if you have less RAM than that, swiotlb wouldn't get set up and the
IOMMU _would_ still end up being initialised, even though we never
claimed to detect it.

This patch also sets the dmar_disabled flag when the error is detected
during the initial detection phase -- so that the later call to
intel_iommu_init() will return without doing anything, regardless of
whether swiotlb is used or not.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoMerge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
Linus Torvalds [Thu, 19 Nov 2009 02:49:49 +0000]
Merge branch 'fixes' of git://git./linux/kernel/git/davej/cpufreq

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Fix stale cpufreq_cpu_governor pointer
  [CPUFREQ] Resolve time unit thinko in ondemand/conservative govs
  [CPUFREQ] speedstep-ich: fix error caused by 394122ab144dae4b276d74644a2f11c44a60ac5c
  [CPUFREQ] Fix use after free on governor restore
  [CPUFREQ] acpi-cpufreq: blacklist Intel 0f68: Fix HT detection and put in notification message
  [CPUFREQ] powernow-k8: Fix test in get_transition_latency()
  [CPUFREQ] longhaul: select Longhaul version 2 for capable CPUs

11 years agostrcmp: fix overflow and possibly signedness error
Linus Torvalds [Wed, 18 Nov 2009 21:31:52 +0000]
strcmp: fix overflow and possibly signedness error

Doing the strcmp return value as

signed char __res = *cs - *ct;

is wrong for two reasons.  The subtraction can overflow because __res
doesn't use a type big enough.  Moreover the compared bytes should be
interpreted as unsigned char as specified by POSIX.

The same problem is fixed in strncmp.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoMerge branch 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied...
Linus Torvalds [Thu, 19 Nov 2009 01:08:16 +0000]
Merge branch 'agp-fixes' of git://git./linux/kernel/git/airlied/agp-2.6

* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
  agp/intel-agp: Set dma_mask for capable chipsets before agp_add_bridge()

11 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris...
Linus Torvalds [Thu, 19 Nov 2009 00:58:34 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  ima: replace GFP_KERNEL with GFP_NOFS

11 years agoagp/intel-agp: Set dma_mask for capable chipsets before agp_add_bridge()
David Woodhouse [Wed, 18 Nov 2009 10:22:46 +0000]
agp/intel-agp: Set dma_mask for capable chipsets before agp_add_bridge()

We should set this before calling agp_add_bridge() so that it's done
before we map the scratch page too.

This should probably fix the regression reported as k.o. bug #14627.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

11 years agoMerge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Wed, 18 Nov 2009 23:00:21 +0000]
Merge branch 'omap-fixes-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  OMAP: cs should be positive in gpmc_cs_free()
  omap: fix unlikely(x) < y
  omap3: clock: Fixed dpll3_m2x2 rate calculation
  omap3: clock: Fix the DPLL freqsel computations
  omap: Fix keymap for zoom2 according to matrix keypad framwork

11 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
Linus Torvalds [Wed, 18 Nov 2009 22:59:49 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ASoC: tlv320aic23 fix rate selection
  ASoC: OMAP3 Pandora: update for TWL4030 codec changes
  ASoC: Modifying the license string GPLv2 for OMAP3 EVM
  ALSA: hda - Fix quirk for VAIO type G
  ALSA: usb - Quirk to disable master volume control in PCM2702

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Wed, 18 Nov 2009 22:54:45 +0000]
Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
  cxgb3: fix premature page unmap
  ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
  vlan: Fix register_vlan_dev() error path
  gro: Fix illegal merging of trailer trash
  sungem: Fix Serdes detection.
  net: fix mdio section mismatch warning
  ppp: fix BUG on non-linear SKB (multilink receive)
  ixgbe: Fixing EEH handler to handle more than one error
  net: Fix the rollback test in dev_change_name()
  Revert "isdn: isdn_ppp: Use SKB list facilities instead of home-grown implementation."
  TI Davinci EMAC : Fix Console Hang when bringing the interface down
  smsc911x: Fix Console Hang when bringing the interface down.
  mISDN: fix error return in HFCmulti_init()
  forcedeth: mac address fix
  r6040: fix version printing
  Bluetooth: Fix regression with L2CAP configuration in Basic Mode
  Bluetooth: Select Basic Mode as default for SOCK_SEQPACKET
  Bluetooth: Set general bonding security for ACL by default
  r8169: Fix receive buffer length when MTU is between 1515 and 1536
  can: add the missing netlink get_xstats_size callback

11 years agoima: replace GFP_KERNEL with GFP_NOFS
Mimi Zohar [Wed, 18 Nov 2009 21:16:06 +0000]
ima: replace GFP_KERNEL with GFP_NOFS

While running fsstress tests on the NFSv4 mounted ext3 and ext4
filesystem, the following call trace was generated on the nfs
server machine.

Replace GFP_KERNEL with GFP_NOFS in ima_iint_insert() to avoid a
potential deadlock.

    [ INFO: inconsistent lock state ]
    2.6.31-31.el6.x86_64 #1
    inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
    kswapd2/75 [HC0[0]:SC0[0]:HE1:SE1] takes:
     (jbd2_handle){+.+.?.}, at: [<ffffffff811edd5e>] jbd2_journal_start+0xfe/0x13f
    {RECLAIM_FS-ON-W} state was registered at:
      [<ffffffff81091e40>] mark_held_locks+0x65/0x99
      [<ffffffff81091f31>] lockdep_trace_alloc+0xbd/0xf5
      [<ffffffff81126fdd>] kmem_cache_alloc+0x40/0x185
      [<ffffffff812344d7>] ima_iint_insert+0x3d/0xf1
      [<ffffffff812345b0>] ima_inode_alloc+0x25/0x44
      [<ffffffff811484ac>] inode_init_always+0xec/0x271
      [<ffffffff81148682>] alloc_inode+0x51/0xa1
      [<ffffffff81148700>] new_inode+0x2e/0x94
      [<ffffffff811b2f08>] ext4_new_inode+0xb8/0xdc9
      [<ffffffff811be611>] ext4_create+0xcf/0x175
      [<ffffffff8113e2cd>] vfs_create+0x82/0xb8
      [<ffffffff8113f337>] do_filp_open+0x32c/0x9ee
      [<ffffffff811309b9>] do_sys_open+0x6c/0x12c
      [<ffffffff81130adc>] sys_open+0x2e/0x44
      [<ffffffff81011e42>] system_call_fastpath+0x16/0x1b
      [<ffffffffffffffff>] 0xffffffffffffffff
    irq event stamp: 90371
    hardirqs last  enabled at (90371): [<ffffffff8112708d>]
    hardirqs last disabled at (90370): [<ffffffff81127026>]
    softirqs last  enabled at (89492): [<ffffffff81068ecf>]
    softirqs last disabled at (89477): [<ffffffff8101312c>] call_softirq+0x1c/0x30

    other info that might help us debug this:
    2 locks held by kswapd2/75:
     #0:  (shrinker_rwsem){++++..}, at: [<ffffffff810f98ba>] shrink_slab+0x44/0x177
     #1:  (&type->s_umount_key#25){++++..}, at: [<ffffffff811450ba>]

Reported-by: Muni P. Beerakam <mbeeraka@in.ibm.com>
Reported-by: Amit K. Arora <amitarora@in.ibm.com>
Cc: stable@kernel.org
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>

11 years agoOMAP: cs should be positive in gpmc_cs_free()
Roel Kluin [Tue, 17 Nov 2009 22:39:06 +0000]
OMAP: cs should be positive in gpmc_cs_free()

The index `cs' is signed, test whether it is negative before we release

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

11 years agoomap: fix unlikely(x) < y
Roel Kluin [Tue, 17 Nov 2009 22:39:03 +0000]
omap: fix unlikely(x) < y

The closing parenthesis was not in the right location.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

11 years agoMerge branch 'fix/asoc' into for-linus
Takashi Iwai [Wed, 18 Nov 2009 15:38:58 +0000]
Merge branch 'fix/asoc' into for-linus

11 years agoMerge branch 'fix/hda' into for-linus
Takashi Iwai [Wed, 18 Nov 2009 15:38:49 +0000]
Merge branch 'fix/hda' into for-linus

11 years agoMerge branch 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal...
Linus Torvalds [Wed, 18 Nov 2009 15:38:19 +0000]
Merge branch 'sh/for-2.6.32' of git://git./linux/kernel/git/lethal/sh-2.6

* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Fixup last users of irq_chip->typename
  uio: pm_runtime_disable is needed if failed

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
Linus Torvalds [Wed, 18 Nov 2009 15:37:51 +0000]
Merge git://git./linux/kernel/git/gregkh/usb-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: option.c: add support for D-Link DWM-162-U5
  USB: usbmon: fix bug in mon_buff_area_shrink
  USB: xhci: Fix scratchpad deallocation.
  USB: xhci: Fix TRB physical to virtual address translation.
  USB: xhci: Fix bug memory free after failed initialization.
  USB: cdc_acm: Fix memory leak after hangup
  USB: cdc_acm: Fix race condition when opening tty
  USB: ohci: quirk AMD prefetch for USB 1.1 ISO transfer

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
Linus Torvalds [Wed, 18 Nov 2009 15:37:38 +0000]
Merge git://git./linux/kernel/git/gregkh/tty-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  tty: cp210x: Fix carrier handling
  tty_port: If we are opened non blocking we still need to raise the carrier

11 years agoASoC: tlv320aic23 fix rate selection
Troy Kisky [Tue, 17 Nov 2009 20:51:01 +0000]
ASoC: tlv320aic23 fix rate selection

Fix the ordering of sr_valid_mask array.
The lower bit of the index represents USB
not bosr.

Reported-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

11 years agoASoC: OMAP3 Pandora: update for TWL4030 codec changes
Grazvydas Ignotas [Sat, 7 Nov 2009 21:16:12 +0000]
ASoC: OMAP3 Pandora: update for TWL4030 codec changes

A while ago TWL4030 had it's playback stream name changed, but
pandora needs it for it's playback path. Update to correct stream
name so that playback works again.

Also mark VIBRA output as not connected.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

11 years agoASoC: Modifying the license string GPLv2 for OMAP3 EVM
Anuj Aggarwal [Tue, 17 Nov 2009 16:13:42 +0000]
ASoC: Modifying the license string GPLv2 for OMAP3 EVM

Correcting the license string from GPLv2 -> GPL v2.
Found the problem while building OMAP3 ASoC driver as

Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

11 years agocxgb3: fix premature page unmap
Divy Le Ray [Tue, 17 Nov 2009 16:38:28 +0000]
cxgb3: fix premature page unmap

unmap Rx page only when guaranteed that this page won't be
used anymore to allocate rx page chunks.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

11 years agoibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
Dave Mitchell [Tue, 17 Nov 2009 14:56:55 +0000]
ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts

The TRT bit shifts were reversed for EMAC4 and non-EMAC4 during the
port from ibm_emac to ibm_newemac. This patch corrects that error.

Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Feng Kan <fkan@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

11 years ago[CPUFREQ] Fix stale cpufreq_cpu_governor pointer
Prarit Bhargava [Thu, 12 Nov 2009 14:18:46 +0000]
[CPUFREQ] Fix stale cpufreq_cpu_governor pointer


Attached is an update of my patch against the cpufreq fixes branch.

Before applying the patch I compiled and booted the tree to see if the panic
was still there -- to my surprise it was not.  This is because of the conversion
of cpufreq_cpu_governor to a char[].

While the panic is kaput, the problem of stale data continues and my patch is
still valid.  It is possible to end up with the wrong governor after hotplug
events because CPUFREQ_DEFAULT_GOVERNOR is statically linked to a default,
while the cpu siblings may have had a different governor assigned by a user.

ie) the patch is still needed in order to keep the governors assigned
properly when hotplugging devices

Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>

11 years ago[CPUFREQ] Resolve time unit thinko in ondemand/conservative govs
Pallipadi, Venkatesh [Thu, 12 Nov 2009 00:50:29 +0000]
[CPUFREQ] Resolve time unit thinko in ondemand/conservative govs

ondemand and conservative governors are messing up time units in the
code path where NO_HZ is not enabled and ignore_nice is set. The walltime
idletime stored is in jiffies and nice time calculation is happening in

The problem was reported and diagnosed by Alexander here.

The patch below fixes this thinko.

Reported-by: Alexander Miller <Miller@fmi.uni-stuttgart.de>
Tested-by: Alexander Miller <Miller@fmi.uni-stuttgart.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>

11 years ago[CPUFREQ] speedstep-ich: fix error caused by 394122ab144dae4b276d74644a2f11c44a60ac5c
Rusty Russell [Tue, 3 Nov 2009 07:35:30 +0000]
[CPUFREQ] speedstep-ich: fix error caused by 394122ab144dae4b276d74644a2f11c44a60ac5c

"[CPUFREQ] cpumask: avoid playing with cpus_allowed in speedstep-ich.c"
changed the code to mistakenly pass the current cpu as the "processor"
argument of speedstep_get_frequency(), whereas it should be the type of
the processor.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=14340

Based on a patch by Dave Mueller.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Dominik Brodowski <linux@brodo.de>
Reported-by: Dave Mueller <dave.mueller@gmx.ch>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>

11 years ago[CPUFREQ] Fix use after free on governor restore
Dmitry Monakhov [Sun, 4 Oct 2009 20:38:55 +0000]
[CPUFREQ] Fix use after free on governor restore

Currently on governer backup/restore path we storing governor's pointer.
This is wrong because one may unload governor's module after cpu goes
offline. As result use-after-free will take place on restored cpu.
It is not easy to exploit this bug, but still we have to close this
issue ASAP. Issue was introduced by following commit

#!/bin/sh -x
modprobe acpi_cpufreq
# Any non default governor, in may case it is "ondemand"
modprobe cpufreq_ondemand
echo ondemand > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
rmmod acpi_cpufreq
rmmod cpufreq_ondemand
modprobe acpi_cpufreq  # << use-after-free here.

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Dave Jones <davej@redhat.com>

11 years ago[CPUFREQ] acpi-cpufreq: blacklist Intel 0f68: Fix HT detection and put in notificatio...
John Villalovos [Fri, 25 Sep 2009 17:30:08 +0000]
[CPUFREQ] acpi-cpufreq: blacklist Intel 0f68: Fix HT detection and put in notification message

Removing the SMT/HT check, since the Errata doesn't mention

Adding in a printk, so that the user knows why acpi-cpufreq refuses to
load.  Also, once system is blacklisted, don't repeat checks to see if
blacklisted.  This also causes the message to only be printed once,
rather than for each CPU.

Signed-off-by: John L. Villalovos <john.l.villalovos@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>

11 years ago[CPUFREQ] powernow-k8: Fix test in get_transition_latency()
Roel Kluin [Tue, 6 Oct 2009 15:36:53 +0000]
[CPUFREQ] powernow-k8: Fix test in get_transition_latency()

Not makes it a bool before the comparison.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>

11 years ago[CPUFREQ] longhaul: select Longhaul version 2 for capable CPUs
Krzysztof Helt [Sat, 24 Oct 2009 15:25:38 +0000]
[CPUFREQ] longhaul: select Longhaul version 2 for capable CPUs

There is a typo in the longhaul detection code so only Longhaul v1 or Longhaul v3
is selected. The Longhaul v2 is not selected even for CPUs which are capable of.

Tested on PCChips Giga Pro board. Frequency changes work and the Longhaul v2
detects that the board is not capable of changing CPU voltage.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Dave Jones <davej@redhat.com>

11 years agoMerge branch 'sh/stable-updates'
Paul Mundt [Wed, 18 Nov 2009 01:53:52 +0000]
Merge branch 'sh/stable-updates'

11 years agosh: Fixup last users of irq_chip->typename
Thomas Gleixner [Tue, 17 Nov 2009 22:50:45 +0000]
sh: Fixup last users of irq_chip->typename

The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agofcntl: rename F_OWNER_GID to F_OWNER_PGRP
Peter Zijlstra [Tue, 17 Nov 2009 22:06:24 +0000]
fcntl: rename F_OWNER_GID to F_OWNER_PGRP

This is for consistency with various ioctl() operations that include the
suffix "PGRP" in their names, and also for consistency with PRIO_PGRP,
used with setpriority() and getpriority().  Also, using PGRP instead of
GID avoids confusion with the common abbreviation of "group ID".

I'm fine with anything that makes it more consistent, and if PGRP is what
is the predominant abbreviation then I see no need to further confuse
matters by adding a third one.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoprocfs: fix /proc/<pid>/stat stack pointer for kernel threads
Stefani Seibold [Tue, 17 Nov 2009 22:06:23 +0000]
procfs: fix /proc/<pid>/stat stack pointer for kernel threads

Fix a small issue for the stack pointer in /proc/<pid>/stat.  In case of a
kernel thread the value of the printed stack pointer should be 0.

Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agomm: allow memory hotplug and hibernation in the same kernel
Andi Kleen [Tue, 17 Nov 2009 22:06:22 +0000]
mm: allow memory hotplug and hibernation in the same kernel

Allow memory hotplug and hibernation in the same kernel

Memory hotplug and hibernation were exclusive in Kconfig.  This is
obviously a problem for distribution kernels who want to support both in
the same image.

After some discussions with Rafael and others the only problem is with
parallel memory hotadd or removal while a hibernation operation is in
process.  It was also working for s390 before.

This patch removes the Kconfig level exclusion, and simply makes the
memory add / remove functions grab the pm_mutex to exclude against

Fixes a regression - old kernels didn't exclude memory hotadd and

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoworkqueue: fix race condition in schedule_on_each_cpu()
Tejun Heo [Tue, 17 Nov 2009 22:06:20 +0000]
workqueue: fix race condition in schedule_on_each_cpu()

Commit 65a64464349883891e21e74af16c05d6e1eeb4e9 ("HWPOISON: Allow
schedule_on_each_cpu() from keventd") which allows schedule_on_each_cpu()
to be called from keventd added a race condition.  schedule_on_each_cpu()
may race with cpu hotplug and end up executing the function twice on a

Fix it by moving direct execution into the section protected with
get/put_online_cpus().  While at it, update code such that direct
execution is done after works have been scheduled for all other cpus and
drop unnecessary cpu != orig test from flush loop.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agomm/memory_hotplug: fix section mismatch
Hidetoshi Seto [Tue, 17 Nov 2009 22:06:18 +0000]
mm/memory_hotplug: fix section mismatch

With CONFIG_MEMORY_HOTPLUG I got following warning:

WARNING: vmlinux.o(.text+0x1276b0): Section mismatch in reference from
the function hotadd_new_pgdat() to the function
The function hotadd_new_pgdat() references
the function __meminit free_area_init_node().
This is often because hotadd_new_pgdat lacks a __meminit
annotation or the annotation of free_area_init_node is wrong.

Use __ref to fix this.

Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoMAINTAINERS: KMEMCHECK: add file patterns, use M: for Pekka's name and address
Joe Perches [Tue, 17 Nov 2009 22:06:15 +0000]
MAINTAINERS: KMEMCHECK: add file patterns, use M: for Pekka's name and address

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agodrivers/video/da8xx-fb.c: fix error return
Roel Kluin [Tue, 17 Nov 2009 22:06:15 +0000]
drivers/video/da8xx-fb.c: fix error return

The return should be negative on errors

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agospi: error status should be negative
Roel Kluin [Tue, 17 Nov 2009 22:06:14 +0000]
spi: error status should be negative

Return a negative error value instead of a positive

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoUSB: option.c: add support for D-Link DWM-162-U5
Zhang Le [Wed, 4 Nov 2009 15:22:59 +0000]
USB: option.c: add support for D-Link DWM-162-U5

Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.

The device appears first as CD-only 05c6:2100 device and must be
switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.

The MessageContent for usb_modeswitch.conf is:

Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

11 years agoUSB: usbmon: fix bug in mon_buff_area_shrink
Alan Stern [Wed, 4 Nov 2009 16:35:53 +0000]
USB: usbmon: fix bug in mon_buff_area_shrink

This patch (as1299b) fixes a bug in an error-handling path of usbmon's
binary interface.  The storage area for URB data is divided into
fixed-size blocks.  If an URB's data can't be copied, the area
reserved for it should be decreased to the size of the truncated
information (rounded up to a block boundary).  Rounding up the amount
to be removed and subtracting it from the reserved size is definitely
the wrong thing to do.

Also, when the data for an isochronous URB can't be copied, we can
still copy the isoc packet descriptors.  In fact the current code does
copy the descriptors, but then sets the capture length to 0 so they
remain inaccessible.  The capture length should be reduced to the
length of the descriptors, not set to 0.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

11 years agoUSB: xhci: Fix scratchpad deallocation.
Sarah Sharp [Wed, 4 Nov 2009 19:22:19 +0000]
USB: xhci: Fix scratchpad deallocation.

The scratchpad_free() function uses xhci->page_size to free some memory
with pci_free_consistent().  However, the page_size is set to zero before
the call, causing kernel oopses on driver unload.  Call scratchpad_free()
before setting xhci->page_size to zero.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: John Youn <John.Youn@synopsys.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

11 years agoUSB: xhci: Fix TRB physical to virtual address translation.
Sarah Sharp [Wed, 4 Nov 2009 06:02:24 +0000]
USB: xhci: Fix TRB physical to virtual address translation.

The trb_in_td() function in the xHCI driver is supposed to translate a
physical transfer buffer request (TRB) into a virtual pointer to the ring
segment that TRB is in.

Unfortunately, a mistake in this function may cause endless loops as the
driver searches through the linked list of ring segments over and over
again.  Fix a couple bugs that may lead to loops or bad output:

1. Bail out if we get a NULL pointer when translating the segment's
private structure and the starting DMA address of the segment chunk.  If
this happens, we've been handed a starting TRB pointer from a different

2. Make sure the function works when there's multiple segments in the
ring.  In the while loop to search through the ring segments, use the
current segment variable (cur_seg), rather than the starting segment
variable (start_seg) that is passed in.

3. Stop searching the ring if we've run through all the segments in the

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

11 years agoUSB: xhci: Fix bug memory free after failed initialization.
Sarah Sharp [Wed, 4 Nov 2009 06:02:22 +0000]
USB: xhci: Fix bug memory free after failed initialization.

If the xHCI driver fails during the memory initialization, xhci->ir_set
may not be a valid pointer.  Check that it points to valid DMA'able memory
before writing to that address during the memory freeing process.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

11 years agoUSB: cdc_acm: Fix memory leak after hangup
Francesco Lavra [Tue, 3 Nov 2009 10:53:07 +0000]
USB: cdc_acm: Fix memory leak after hangup

Am Donnerstag, 10. September 2009 15:43:53 schrieb Dietmar Hilbrich:
> Hello,
> i have the following problem with the cdc-acm - driver:
> I'm using the driver with an "Ericsson F3507G" on a Thinkpad T400.
> If a disable the device (with the RFKill-Switch) while it is used by a
> programm like ppp, the driver doesn't seem to correctly clean up the tty,
> even after the program has been closed)
> The tty is still active (e.g. there still exists an entry in
> /sys/dev/char/166:0 if ttyACM0 was used) and if a reacticate the device,
> this device entry will be skipped and the Device-Nodes ttyACM1, ttyACM2
> and ttyACM3 will be used.
> This problem was introduced with the commit
10077d4a6674f535abdbe25cdecb1202af7948f1 (before 2.6.31-rc1) and still
> exists in 2.6.31.
> I was able the fix this problem with the following patch:
> diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
> index 2bfc41e..0970d2f 100644
> --- a/drivers/usb/class/cdc-acm.c
> +++ b/drivers/usb/class/cdc-acm.c
> @@ -676,6 +676,7 @@ static void acm_tty_hangup(struct tty_struct *tty)
>         struct acm *acm = tty->driver_data;
>         tty_port_hangup(&acm->port);
>         acm_port_down(acm, 0);
> +       acm_tty_unregister(acm);
>  }

I have the same problem with cdc-acm (I'm using a Samsung SGH-U900): when I
unplug it from the USB port during a PPP connection, the ppp daemon gets the
hangup correctly (and closes the device), but the struct acm corresponding to
the device disconnected is not freed. Hence reconnecting the device results in
creation of /dev/ttyACM(x+1). The same happens when the system is hibernated
during a PPP connection.

This memory leak is due to the fact that when the tty is hung up,
tty_port_close_start() returns always zero, and acm_tty_close() never reaches
the point where acm_tty_unregister() is called.

Here is a fix for this.

Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

11 years agoUSB: cdc_acm: Fix race condition when opening tty
Henry Gebhardt [Wed, 4 Nov 2009 10:19:28 +0000]
USB: cdc_acm: Fix race condition when opening tty

If acm_rx_tasklet() gets called before tty_port_block_til_ready()
returns, then bulk IN urbs may not be sent. This fixes it.

Signed-off-by: Henry Gebhardt <gebhardt@astro.uni-tuebingen.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

11 years agoUSB: ohci: quirk AMD prefetch for USB 1.1 ISO transfer
Libin Yang [Wed, 4 Nov 2009 06:55:18 +0000]
USB: ohci: quirk AMD prefetch for USB 1.1 ISO transfer

The following patch in the driver is required to avoid USB 1.1 device
failures that may occur due to requests from USB OHCI controllers may
be overwritten if the latency for any pending request by the USB
controller is very long (in the range of milliseconds).

Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

11 years agotty: cp210x: Fix carrier handling
Alan Cox [Wed, 28 Oct 2009 20:12:33 +0000]
tty: cp210x: Fix carrier handling

Original discussion:

9a68e39d4a701fb3be03cae9b462408664ebd205 broke carrier handling so that a
cp210x setup which needed the carrier lines set up (non CLOCAL) which did
not make a call which set the termios bits left the lines down even if
CLOCAL was not asserted.

Fix this not by reverting but by adding the proper dtr_rts and
carrier_raised methods. This both sets the modem lines properly and also
implements the correct blocking semantics for the port as required by

Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Tested-by:  Karl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

11 years agotty_port: If we are opened non blocking we still need to raise the carrier
Alan Cox [Wed, 28 Oct 2009 20:12:32 +0000]
tty_port: If we are opened non blocking we still need to raise the carrier

Original discussion:

The tty_port code inherited a bug common to various drivers it was based
upon. If the tty is opened O_NONBLOCK we do not wait for the carrier to be
raised but we must still raise our modem lines if appropriate.

(There is a second question here about whether we should do so if CLOCAL is
 set but that can wait)

Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Tested-by:  Karl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

11 years agoomap3: clock: Fixed dpll3_m2x2 rate calculation
Tero Kristo [Mon, 16 Nov 2009 13:36:54 +0000]
omap3: clock: Fixed dpll3_m2x2 rate calculation

Current calculation does not take into account any changes to M2 divisor, and
thus when we change VDD2 OPP, dpll3_m2x2 rate does not change. Fixed by
re-routing dpll3_m2x2 parent to dpll3_m2.

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

11 years agoomap3: clock: Fix the DPLL freqsel computations
Rajendra Nayak [Mon, 16 Nov 2009 13:36:53 +0000]
omap3: clock: Fix the DPLL freqsel computations

Fix the freqsel value computation. Use n instead of (n+1)

The formula in the TRM uses a zero-based N, hence the (n+1); however
at this point in the clock34xx.c code, N is one-based.

Hayati Bayrakdar <h-bayrakdar@ti.com> and Nishanth Menon <nm@ti.com> helped
track down this bug.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: modified commit message]
Cc: Hayati Bayrakdar <h-bayrakdar@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
Linus Torvalds [Tue, 17 Nov 2009 19:01:54 +0000]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] bfa: declare MODULE_FIRMWARE
  [SCSI] gdth: Prevent negative offsets in ioctl CVE-2009-3080
  [SCSI] libsas: do not set res = 0 in sas_ex_discover_dev()
  [SCSI] Fix incorrect reporting of host protection capabilities
  [SCSI] pmcraid: Fix ppc64 driver build for using cpu_to_le32 on U8 data type
  [SCSI] ipr: add workaround for MSI interrupts on P7
  [SCSI] scsi_transport_fc: Fix WARN message for FC passthru failure paths
  [SCSI] bfa: fix test in bfad_os_fc_host_init()

11 years agoMerge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
Linus Torvalds [Tue, 17 Nov 2009 17:42:35 +0000]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: copy li_lsn before dropping AIL lock
  XFS bug in log recover with quota (bugzilla id 855)

11 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Linus Torvalds [Tue, 17 Nov 2009 17:20:50 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: lifebook - fix settings for CF-72
  Input: psmouse - fix breakage introduced by b7802c5c1ea

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6
Linus Torvalds [Tue, 17 Nov 2009 17:20:38 +0000]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: clear server inode number flag while autodisabling

11 years agoMerge master.kernel.org:/home/rmk/linux-2.6-arm
Linus Torvalds [Tue, 17 Nov 2009 17:19:54 +0000]
Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] pxa: ensure mfp is in correct range in mfp_{read,write}
  [ARM] pxa/hx4700: fix hx4700 touchscreen pressure values
  ARM: 5787/1: U300 COH 901 331 fixes
  ARM: Fix warning in sa1100-flash.c
  [ARM] Kirkwood: disable propagation of mbus error to the CPU local bus
  [ARM] pxa: fix incorrect mfp_to_gpio() conversion
  [ARM] pxa/colibri: fix AC97 ifdefs and add missing include
  [ARM] pxa: fix missing underscores in mfp-pxa910.h
  [ARM] pxa: fix interrupts number calculation when CONFIG_PXA_HAVE_ISA_IRQS=y

11 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
Linus Torvalds [Tue, 17 Nov 2009 17:19:27 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/lrg/voltage-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  dereferencing freed memory regulator_fixed_voltage_remove()
  regulator: Fix check of unsigned return value and transmit errors in wm831x_gp_ldo_get_mode()
  regulator: Handle missing constraints in _regulator_disable()

11 years agoMerge branch 'for-linus' of git://github.com/at91linux/linux-2.6-at91
Linus Torvalds [Tue, 17 Nov 2009 17:19:13 +0000]
Merge branch 'for-linus' of git://github.com/at91linux/linux-2.6-at91

* 'for-linus' of git://github.com/at91linux/linux-2.6-at91:
  at91: at91sam9g20ek modify dual slot evaluation kit

11 years agoMerge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelv...
Linus Torvalds [Tue, 17 Nov 2009 17:17:40 +0000]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/jdelvare/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (adt7475) Fix sysfs file names
  hwmon: (adt7475) Cache limits for 60 seconds
  hwmon: (adt7475) Fix temperature fault flags
  hwmon: (s3c-hwmon) Ignore invalid divider settings

11 years agoMerge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds
Linus Torvalds [Tue, 17 Nov 2009 17:16:57 +0000]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds

* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
  leds-gpio: fix possible crash on OF device unbinding
  backlight: Fix backlight limiting on spitz/corgi devices
  backlight: lcd - Fix wrong sizeof

11 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
Linus Torvalds [Tue, 17 Nov 2009 17:15:48 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: ice1724 - make some bitfields unsigned
  ALSA: hda - Dell Studio 1557 hd-audio quirk
  ALSA: ice1724 - Fix section mismatch in prodigy_hd2_resume()
  ALSA: hda - Add another Nvidia HDMI codec id (10de:0005)
  ALSA: hda: Use model=mb5 for MacBookPro 5,2

11 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke...
Linus Torvalds [Tue, 17 Nov 2009 17:15:18 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/ryusuke/nilfs2

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: deleted inconsistent comment in nilfs_load_inode_block()
  nilfs2: deleted struct nilfs_dat_group_desc
  nilfs2: fix lock order reversal in chcp operation

11 years agoMerge branch 'hostprogs-wmissing-prototypes' of git://git.kernel.org/pub/scm/linux...
Linus Torvalds [Tue, 17 Nov 2009 17:14:49 +0000]
Merge branch 'hostprogs-wmissing-prototypes' of git://git./linux/kernel/git/josh/linux-misc

* 'hostprogs-wmissing-prototypes' of git://git.kernel.org/pub/scm/linux/kernel/git/josh/linux-misc:
  Makefile: Add -Wmising-prototypes to HOSTCFLAGS
  oss: Mark loadhex static in hex2hex.c
  dtc: Mark various internal functions static
  dtc: Set "noinput" in the lexer to avoid an unused function
  drm: radeon: Mark several functions static in mkregtable
  arch/sparc/boot/*.c: Mark various internal functions static
  arch/powerpc/boot/addRamDisk.c: Mark several internal functions static
  arch/alpha/boot/tools/objstrip.c: Mark "usage" static
  Documentation/vm/page-types.c: Declare checked_open static
  genksyms: Mark is_reserved_word static
  kconfig: Mark various internal functions static
  kconfig: Make zconf.y work with current bison

11 years agofcntl: Use consistent values for F_[GS]ETOWN_EX
Stephen Rothwell [Sat, 14 Nov 2009 09:45:06 +0000]
fcntl: Use consistent values for F_[GS]ETOWN_EX

These values were only introduced during this release cycle, so it is
still early enough to get them right.

alpha uses the same values that are in asm-generic/fcntl.h, so just
remove them.

parisc uses the values interchanged for no apparent reason, so remove
them to give us consistency across all architectures.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoxfs: copy li_lsn before dropping AIL lock
Nathaniel W. Turner [Mon, 16 Nov 2009 19:51:48 +0000]
xfs: copy li_lsn before dropping AIL lock

Access to log items on the AIL is generally protected by m_ail_lock;
this is particularly needed when we're getting or setting the 64-bit
li_lsn on a 32-bit platform.  This patch fixes a couple places where we
were accessing the log item after dropping the AIL lock on 32-bit

This can result in a partially-zeroed log->l_tail_lsn if
xfs_trans_ail_delete is racing with xfs_trans_ail_update, and in at
least some cases, this can leave the l_tail_lsn with a zero cycle
number, which means xlog_space_left will think the log is full (unless
CONFIG_XFS_DEBUG is set, in which case we'll trip an ASSERT), leading to
processes stuck forever in xlog_grant_log_space.

Thanks to Adrian VanderSpek for first spotting the race potential and to
Dave Chinner for debug assistance.

Signed-off-by: Nathaniel W. Turner <nate@houseofnate.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>

11 years agoXFS bug in log recover with quota (bugzilla id 855)
Jan Rekorajski [Mon, 16 Nov 2009 11:57:02 +0000]
XFS bug in log recover with quota (bugzilla id 855)

I was hit by a bug in linux 2.6.31 when XFS is not able to recover the
log after a crash if fs was mounted with quotas. Gory details in XFS
bugzilla: http://oss.sgi.com/bugzilla/show_bug.cgi?id=855.

It looks like wrong struct is used in buffer length check, and the following
patch should fix the problem.

xfs_dqblk_t has a size of 104+32 bytes, while xfs_disk_dquot_t is 104 bytes
long, and this is exactly what I see in system logs - "XFS: dquot too small
(104) in xlog_recover_do_dquot_trans."

Signed-off-by: Jan Rekorajski <baggins@sith.mimuw.edu.pl>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>

11 years agoALSA: hda - Fix quirk for VAIO type G
Takashi Iwai [Tue, 17 Nov 2009 14:58:35 +0000]
ALSA: hda - Fix quirk for VAIO type G

Vaio type G laptop doesn't work with the current quirk setup.
After some tests, it turned out that it should be model=auto as default.

Reported-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

11 years agoALSA: usb - Quirk to disable master volume control in PCM2702
Javier Kohen [Tue, 17 Nov 2009 14:36:13 +0000]
ALSA: usb - Quirk to disable master volume control in PCM2702

Disable the master volume control in the PCM2702 chipset.

The datasheet documents two independent channel volume controls, one
master mute control and one master volume control. All controls are
fully functional except for the master volume control, which returns
USB stalls on all GET requests.

Signed-off-by: Javier Kohen <jkohen@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>