--- /dev/null
+* ARM L2 Cache Controller
+
+ARM cores often have a separate level 2 cache controller. There are various
+implementations of the L2 cache controller with compatible programming models.
+The ARM L2 cache representation in the device tree should be done as follows:
+
+Required properties:
+
+- compatible : should be one of:
+ "arm,pl310-cache"
+ "arm,l220-cache"
+ "arm,l210-cache"
+- cache-unified : Specifies the cache is a unified cache.
+- cache-level : Should be set to 2 for a level 2 cache.
+- reg : Physical base address and size of cache controller's memory mapped
+ registers.
+
+Optional properties:
+
+- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
+ read, write and setup latencies. Minimum valid values are 1. Controllers
+ without setup latency control should use a value of 0.
+- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
+ read, write and setup latencies. Controllers without setup latency control
+ should use 0. Controllers without separate read and write Tag RAM latency
+ values should only use the first cell.
+- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
+- arm,filter-ranges : <start length> Starting address and length of window to
+ filter. Addresses in the filter window are directed to the M1 port. Other
+ addresses will go to the M0 port.
+- interrupts : 1 combined interrupt.
+
+Example:
+
+L2: cache-controller {
+ compatible = "arm,pl310-cache";
+ reg = <0xfff12000 0x1000>;
+ arm,data-latency = <1 1 1>;
+ arm,tag-latency = <2 2 2>;
+ arm,filter-latency = <0x80000000 0x8000000>;
+ cache-unified;
+ cache-level = <2>;
+ interrupts = <45>;
+};
select CLKDEV_LOOKUP
select HAVE_MACH_CLKDEV
select GENERIC_GPIO
+ select ARCH_REQUIRE_GPIOLIB
help
Support for ST-Ericsson U300 series mobile platforms.
*/
#include <linux/device.h>
+#include <linux/gpio.h>
#include <linux/string.h>
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/io.h>
-#include <asm/gpio.h>
#include <asm/hardware/scoop.h>
/* PCMCIA to Scoop linkage
/* Private internal data */
const char *card_desc; /* Card description */
- CONST unsigned int podaddr; /* Base Linux address for card */
CONST loader_t loader; /* loader program */
u64 dma_mask;
};
/* not all ARM platforms necessarily support this API ... */
#include <mach/gpio.h>
+#ifndef __ARM_GPIOLIB_COMPLEX
+/* Note: this may rely upon the value of ARCH_NR_GPIOS set in mach/gpio.h */
+#include <asm-generic/gpio.h>
+
+/* The trivial gpiolib dispatchers */
+#define gpio_get_value __gpio_get_value
+#define gpio_set_value __gpio_set_value
+#define gpio_cansleep __gpio_cansleep
+#endif
+
+/*
+ * Provide a default gpio_to_irq() which should satisfy every case.
+ * However, some platforms want to do this differently, so allow them
+ * to override it.
+ */
+#ifndef gpio_to_irq
+#define gpio_to_irq __gpio_to_irq
+#endif
+
#endif /* _ARCH_ARM_GPIO_H */
#define L2X0_LOCKDOWN_WAY_D_BASE 0x900
#define L2X0_LOCKDOWN_WAY_I_BASE 0x904
#define L2X0_LOCKDOWN_STRIDE 0x08
+#define L2X0_ADDR_FILTER_START 0xC00
+#define L2X0_ADDR_FILTER_END 0xC04
#define L2X0_TEST_OPERATION 0xF00
#define L2X0_LINE_DATA 0xF10
#define L2X0_LINE_TAG 0xF30
#define L2X0_CACHE_ID_PART_MASK (0xf << 6)
#define L2X0_CACHE_ID_PART_L210 (1 << 6)
#define L2X0_CACHE_ID_PART_L310 (3 << 6)
+#define L2X0_CACHE_ID_RTL_MASK 0x3f
+#define L2X0_CACHE_ID_RTL_R0P0 0x0
+#define L2X0_CACHE_ID_RTL_R1P0 0x2
+#define L2X0_CACHE_ID_RTL_R2P0 0x4
+#define L2X0_CACHE_ID_RTL_R3P0 0x5
+#define L2X0_CACHE_ID_RTL_R3P1 0x6
+#define L2X0_CACHE_ID_RTL_R3P2 0x8
#define L2X0_AUX_CTRL_MASK 0xc0000fff
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT 0
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK 0x7
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT 3
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK (0x7 << 3)
+#define L2X0_AUX_CTRL_TAG_LATENCY_SHIFT 6
+#define L2X0_AUX_CTRL_TAG_LATENCY_MASK (0x7 << 6)
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT 9
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_MASK (0x7 << 9)
#define L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT 16
#define L2X0_AUX_CTRL_WAY_SIZE_SHIFT 17
#define L2X0_AUX_CTRL_WAY_SIZE_MASK (0x7 << 17)
#define L2X0_AUX_CTRL_INSTR_PREFETCH_SHIFT 29
#define L2X0_AUX_CTRL_EARLY_BRESP_SHIFT 30
+#define L2X0_LATENCY_CTRL_SETUP_SHIFT 0
+#define L2X0_LATENCY_CTRL_RD_SHIFT 4
+#define L2X0_LATENCY_CTRL_WR_SHIFT 8
+
+#define L2X0_ADDR_FILTER_EN 1
+
#ifndef __ASSEMBLY__
extern void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask);
+extern int l2x0_of_init(__u32 aux_val, __u32 aux_mask);
+
+struct l2x0_regs {
+ unsigned long phy_base;
+ unsigned long aux_ctrl;
+ /*
+ * Whether the following registers need to be saved/restored
+ * depends on platform
+ */
+ unsigned long tag_latency;
+ unsigned long data_latency;
+ unsigned long filter_start;
+ unsigned long filter_end;
+ unsigned long prefetch_ctrl;
+ unsigned long pwr_ctrl;
+};
+
+extern struct l2x0_regs l2x0_saved_regs;
+
#endif
#endif
#include <mach/hardware.h>
#include <asm-generic/gpio.h>
+#define __ARM_GPIOLIB_COMPLEX
+
#define IOP3XX_N_GPIOS 8
static inline int gpio_get_value(unsigned gpio)
#include <mach/io.h>
/*
+ * This is the limit of PC card/PCI/ISA IO space, which is by default
+ * 64K if we have PC card, PCI or ISA support. Otherwise, default to
+ * zero to prevent ISA/PCI drivers claiming IO space (and potentially
+ * oopsing.)
+ *
+ * Only set this larger if you really need inb() et.al. to operate over
+ * a larger address space. Note that SOC_COMMON ioremaps each sockets
+ * IO space area, and so inb() et.al. must be defined to operate as per
+ * readb() et.al. on such platforms.
+ */
+#ifndef IO_SPACE_LIMIT
+#if defined(CONFIG_PCMCIA_SOC_COMMON) || defined(CONFIG_PCMCIA_SOC_COMMON_MODULE)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffffffff)
+#elif defined(CONFIG_PCI) || defined(CONFIG_ISA) || defined(CONFIG_PCCARD)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffff)
+#else
+#define IO_SPACE_LIMIT ((resource_size_t)0)
+#endif
+#endif
+
+/*
* IO port access primitives
* -------------------------
*
void (*sync)(void);
#endif
void (*set_debug)(unsigned long);
+ void (*resume)(void);
};
#ifdef CONFIG_OUTER_CACHE
outer_cache.disable();
}
+static inline void outer_resume(void)
+{
+ if (outer_cache.resume)
+ outer_cache.resume();
+}
+
#else
static inline void outer_inv_range(phys_addr_t start, phys_addr_t end)
#include <asm/thread_info.h>
#include <asm/memory.h>
#include <asm/procinfo.h>
+#include <asm/hardware/cache-l2x0.h>
#include <linux/kbuild.h>
/*
DEFINE(S_OLD_R0, offsetof(struct pt_regs, ARM_ORIG_r0));
DEFINE(S_FRAME_SIZE, sizeof(struct pt_regs));
BLANK();
+#ifdef CONFIG_CACHE_L2X0
+ DEFINE(L2X0_R_PHY_BASE, offsetof(struct l2x0_regs, phy_base));
+ DEFINE(L2X0_R_AUX_CTRL, offsetof(struct l2x0_regs, aux_ctrl));
+ DEFINE(L2X0_R_TAG_LATENCY, offsetof(struct l2x0_regs, tag_latency));
+ DEFINE(L2X0_R_DATA_LATENCY, offsetof(struct l2x0_regs, data_latency));
+ DEFINE(L2X0_R_FILTER_START, offsetof(struct l2x0_regs, filter_start));
+ DEFINE(L2X0_R_FILTER_END, offsetof(struct l2x0_regs, filter_end));
+ DEFINE(L2X0_R_PREFETCH_CTRL, offsetof(struct l2x0_regs, prefetch_ctrl));
+ DEFINE(L2X0_R_PWR_CTRL, offsetof(struct l2x0_regs, pwr_ctrl));
+ BLANK();
+#endif
#ifdef CONFIG_CPU_HAS_ASID
DEFINE(MM_CONTEXT_ID, offsetof(struct mm_struct, context.id));
BLANK();
memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (IO_SIZE / PGDIR_SIZE));
- src_pgd = pgd_offset(mm, EASI_BASE);
+ src_pgd = pgd_offset(mm, (unsigned long)EASI_BASE);
dst_pgd = pgd_offset(mm, EASI_START);
memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE));
#define ecard_probeirqhw() (0)
#endif
-#ifndef IO_EC_MEMC8_BASE
-#define IO_EC_MEMC8_BASE 0
-#endif
-
-static unsigned int __ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
+static void __iomem *__ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
{
- unsigned long address = 0;
+ void __iomem *address = NULL;
int slot = ec->slot_no;
if (ec->slot_no == 8)
- return IO_EC_MEMC8_BASE;
+ return ECARD_MEMC8_BASE;
ectcr &= ~(1 << slot);
switch (type) {
case ECARD_MEMC:
if (slot < 4)
- address = IO_EC_MEMC_BASE + (slot << 12);
+ address = ECARD_MEMC_BASE + (slot << 14);
break;
case ECARD_IOC:
if (slot < 4)
- address = IO_EC_IOC_BASE + (slot << 12);
-#ifdef IO_EC_IOC4_BASE
+ address = ECARD_IOC_BASE + (slot << 14);
else
- address = IO_EC_IOC4_BASE + ((slot - 4) << 12);
-#endif
+ address = ECARD_IOC4_BASE + ((slot - 4) << 14);
if (address)
- address += speed << 17;
+ address += speed << 19;
break;
-#ifdef IO_EC_EASI_BASE
case ECARD_EASI:
- address = IO_EC_EASI_BASE + (slot << 22);
+ address = ECARD_EASI_BASE + (slot << 24);
if (speed == ECARD_FAST)
ectcr |= 1 << slot;
break;
-#endif
+
default:
break;
}
ecard_t **ecp;
ecard_t *ec;
struct ex_ecid cid;
+ void __iomem *addr;
int i, rc;
ec = ecard_alloc_card(type, slot);
}
rc = -ENODEV;
- if ((ec->podaddr = __ecard_address(ec, type, ECARD_SYNC)) == 0)
+ if ((addr = __ecard_address(ec, type, ECARD_SYNC)) == NULL)
goto nodev;
cid.r_zero = 1;
ec->cid.fiqmask = cid.r_fiqmask;
ec->cid.fiqoff = ecard_gets24(cid.r_fiqoff);
ec->fiqaddr =
- ec->irqaddr = (void __iomem *)ioaddr(ec->podaddr);
+ ec->irqaddr = addr;
if (ec->cid.is) {
ec->irqmask = ec->cid.irqmask;
set_irq_flags(ec->irq, IRQF_VALID);
}
-#ifdef IO_EC_MEMC8_BASE
if (slot == 8)
ec->irq = 11;
-#endif
#ifdef CONFIG_ARCH_RPC
/* On RiscPC, only first two slots have DMA capability */
if (slot < 2)
ecard_probe(slot, ECARD_IOC);
}
-#ifdef IO_EC_MEMC8_BASE
ecard_probe(8, ECARD_IOC);
-#endif
irqhw = ecard_probeirqhw();
#include <asm/mach/irq.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <mach/board.h>
#include <mach/cpu.h>
-#include <mach/gpio.h>
#include <mach/at91cap9.h>
#include <mach/at91cap9_matrix.h>
#include <mach/at91sam9_smc.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200.h>
#include <mach/at91rm9200_mc.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include <mach/at91sam9260.h>
#include <mach/at91sam9260_matrix.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <video/atmel_lcdc.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9261.h>
#include <mach/at91sam9261_matrix.h>
#include <mach/at91sam9_smc.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <video/atmel_lcdc.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9263.h>
#include <mach/at91sam9263_matrix.h>
#include <mach/at91sam9_smc.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <linux/atmel-mci.h>
#include <video/atmel_lcdc.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9g45.h>
#include <mach/at91sam9g45_matrix.h>
#include <mach/at91sam9_smc.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <video/atmel_lcdc.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9rl.h>
#include <mach/at91sam9rl_matrix.h>
#include <mach/at91sam9_smc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/map.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91cap9_matrix.h>
#include <mach/at91sam9_smc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91sam9260_matrix.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200_mc.h>
#include <mach/cpu.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include "generic.h"
#include <linux/types.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include <mach/at91rm9200_mc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200_mc.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200_mc.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200_mc.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200_mc.h>
#include <mach/cpu.h>
#include <linux/clk.h>
#include <linux/errno.h>
+#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/debugfs.h>
#include <mach/hardware.h>
#include <mach/at91_pio.h>
-#include <mach/gpio.h>
-
-#include <asm/gpio.h>
#include "generic.h"
*/
#include <asm/errno.h>
-#include <asm-generic/gpio.h> /* cansleep wrappers */
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
#define gpio_to_irq(gpio) (gpio)
#define irq_to_gpio(irq) (irq)
* 2 of the License, or (at your option) any later version.
*/
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <mach/board.h>
-#include <mach/gpio.h>
/* ------------------------------------------------------------------------- */
* (at your option) any later version.
*/
+#include <linux/gpio.h>
#include <linux/suspend.h>
#include <linux/sched.h>
#include <linux/proc_fs.h>
#include <asm/mach/irq.h>
#include <mach/at91_pmc.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include "generic.h"
# Common objects
obj-y := time.o clock.o serial.o io.o psc.o \
- gpio.o dma.o usb.o common.o sram.o aemif.o
+ dma.o usb.o common.o sram.o aemif.o
obj-$(CONFIG_DAVINCI_MUX) += mux.o
obj-$(CONFIG_ARCH_DAVINCI_DA830) += da830.o devices-da8xx.o
obj-$(CONFIG_ARCH_DAVINCI_DA850) += da850.o devices-da8xx.o
obj-$(CONFIG_ARCH_DAVINCI_TNETV107X) += tnetv107x.o devices-tnetv107x.o
-obj-$(CONFIG_ARCH_DAVINCI_TNETV107X) += gpio-tnetv107x.o
obj-$(CONFIG_AINTC) += irq.o
obj-$(CONFIG_CP_INTC) += cp_intc.o
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <mach/common.h>
#include <mach/time.h>
#include <mach/da8xx.h>
-#include <mach/gpio.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <mach/da8xx.h>
#include <mach/cpufreq.h>
#include <mach/pm.h>
-#include <mach/gpio.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <mach/common.h>
#include <mach/asp.h>
#include <mach/spi.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <asm/mach/map.h>
#include <mach/asp.h>
#include <mach/keyscan.h>
#include <mach/spi.h>
-
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
#include <linux/clk.h>
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
-#include <linux/gpio.h>
#include <asm/mach/map.h>
#include <mach/serial.h>
#include <mach/common.h>
#include <mach/asp.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
#include <linux/clk.h>
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
-#include <linux/gpio.h>
#include <asm/mach/map.h>
#include <mach/serial.h>
#include <mach/common.h>
#include <mach/asp.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
--- /dev/null
+/*
+ * TI DaVinci GPIO Support
+ *
+ * Copyright (c) 2006 David Brownell
+ * Copyright (c) 2007, MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __DAVINCI_DAVINCI_GPIO_H
+#define __DAVINCI_DAVINCI_GPIO_H
+
+#include <linux/io.h>
+#include <linux/spinlock.h>
+
+#include <asm-generic/gpio.h>
+
+#include <mach/irqs.h>
+#include <mach/common.h>
+
+#define DAVINCI_GPIO_BASE 0x01C67000
+
+enum davinci_gpio_type {
+ GPIO_TYPE_DAVINCI = 0,
+ GPIO_TYPE_TNETV107X,
+};
+
+/*
+ * basic gpio routines
+ *
+ * board-specific init should be done by arch/.../.../board-XXX.c (maybe
+ * initializing banks together) rather than boot loaders; kexec() won't
+ * go through boot loaders.
+ *
+ * the gpio clock will be turned on when gpios are used, and you may also
+ * need to pay attention to PINMUX registers to be sure those pins are
+ * used as gpios, not with other peripherals.
+ *
+ * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1). For documentation,
+ * and maybe for later updates, code may write GPIO(N). These may be
+ * all 1.8V signals, all 3.3V ones, or a mix of the two. A given chip
+ * may not support all the GPIOs in that range.
+ *
+ * GPIOs can also be on external chips, numbered after the ones built-in
+ * to the DaVinci chip. For now, they won't be usable as IRQ sources.
+ */
+#define GPIO(X) (X) /* 0 <= X <= (DAVINCI_N_GPIO - 1) */
+
+/* Convert GPIO signal to GPIO pin number */
+#define GPIO_TO_PIN(bank, gpio) (16 * (bank) + (gpio))
+
+struct davinci_gpio_controller {
+ struct gpio_chip chip;
+ int irq_base;
+ spinlock_t lock;
+ void __iomem *regs;
+ void __iomem *set_data;
+ void __iomem *clr_data;
+ void __iomem *in_data;
+};
+
+/* The __gpio_to_controller() and __gpio_mask() functions inline to constants
+ * with constant parameters; or in outlined code they execute at runtime.
+ *
+ * You'd access the controller directly when reading or writing more than
+ * one gpio value at a time, and to support wired logic where the value
+ * being driven by the cpu need not match the value read back.
+ *
+ * These are NOT part of the cross-platform GPIO interface
+ */
+static inline struct davinci_gpio_controller *
+__gpio_to_controller(unsigned gpio)
+{
+ struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs;
+ int index = gpio / 32;
+
+ if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num)
+ return NULL;
+
+ return ctlrs + index;
+}
+
+static inline u32 __gpio_mask(unsigned gpio)
+{
+ return 1 << (gpio % 32);
+}
+
+#endif /* __DAVINCI_DAVINCI_GPIO_H */
#ifndef __DAVINCI_GPIO_H
#define __DAVINCI_GPIO_H
-#include <linux/io.h>
-#include <linux/spinlock.h>
-
#include <asm-generic/gpio.h>
-#include <mach/irqs.h>
-#include <mach/common.h>
-
-#define DAVINCI_GPIO_BASE 0x01C67000
-
-enum davinci_gpio_type {
- GPIO_TYPE_DAVINCI = 0,
- GPIO_TYPE_TNETV107X,
-};
-
-/*
- * basic gpio routines
- *
- * board-specific init should be done by arch/.../.../board-XXX.c (maybe
- * initializing banks together) rather than boot loaders; kexec() won't
- * go through boot loaders.
- *
- * the gpio clock will be turned on when gpios are used, and you may also
- * need to pay attention to PINMUX registers to be sure those pins are
- * used as gpios, not with other peripherals.
- *
- * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1). For documentation,
- * and maybe for later updates, code may write GPIO(N). These may be
- * all 1.8V signals, all 3.3V ones, or a mix of the two. A given chip
- * may not support all the GPIOs in that range.
- *
- * GPIOs can also be on external chips, numbered after the ones built-in
- * to the DaVinci chip. For now, they won't be usable as IRQ sources.
- */
-#define GPIO(X) (X) /* 0 <= X <= (DAVINCI_N_GPIO - 1) */
-
-/* Convert GPIO signal to GPIO pin number */
-#define GPIO_TO_PIN(bank, gpio) (16 * (bank) + (gpio))
-
-struct davinci_gpio_controller {
- struct gpio_chip chip;
- int irq_base;
- spinlock_t lock;
- void __iomem *regs;
- void __iomem *set_data;
- void __iomem *clr_data;
- void __iomem *in_data;
-};
-
-/* The __gpio_to_controller() and __gpio_mask() functions inline to constants
- * with constant parameters; or in outlined code they execute at runtime.
- *
- * You'd access the controller directly when reading or writing more than
- * one gpio value at a time, and to support wired logic where the value
- * being driven by the cpu need not match the value read back.
- *
- * These are NOT part of the cross-platform GPIO interface
- */
-static inline struct davinci_gpio_controller *
-__gpio_to_controller(unsigned gpio)
-{
- struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs;
- int index = gpio / 32;
-
- if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num)
- return NULL;
-
- return ctlrs + index;
-}
-
-static inline u32 __gpio_mask(unsigned gpio)
-{
- return 1 << (gpio % 32);
-}
+/* The inline versions use the static inlines in the driver header */
+#include "gpio-davinci.h"
/*
* The get/set/clear functions will inline when called with constant
return __gpio_cansleep(gpio);
}
-static inline int gpio_to_irq(unsigned gpio)
-{
- return __gpio_to_irq(gpio);
-}
-
static inline int irq_to_gpio(unsigned irq)
{
/* don't support the reverse mapping */
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <mach/psc.h>
#include <mach/cp_intc.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
#include <mach/hardware.h>
#include <mach/tnetv107x.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffff
-
u8 __inb8(unsigned int port);
void __outb8(u8 val, unsigned int port);
#include <mach/fb.h>
#include <mach/ep93xx_keypad.h>
#include <mach/ep93xx_spi.h>
+#include <mach/gpio-ep93xx.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
#include <mach/hardware.h>
#include <mach/fb.h>
#include <mach/ep93xx_spi.h>
+#include <mach/gpio-ep93xx.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-/*
- * arch/arm/mach-ep93xx/include/mach/gpio.h
- */
+/* Include file for the EP93XX GPIO controller machine specifics */
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
+#ifndef __GPIO_EP93XX_H
+#define __GPIO_EP93XX_H
/* GPIO port A. */
#define EP93XX_GPIO_LINE_A(x) ((x) + 0)
/* maximum value for irq capable line identifiers */
#define EP93XX_GPIO_LINE_MAX_IRQ EP93XX_GPIO_LINE_F(7)
-/* new generic GPIO API - see Documentation/gpio.txt */
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-
-/*
- * Map GPIO A0..A7 (0..7) to irq 64..71,
- * B0..B7 (7..15) to irq 72..79, and
- * F0..F7 (16..24) to irq 80..87.
- */
-#define gpio_to_irq(gpio) \
- (((gpio) <= EP93XX_GPIO_LINE_MAX_IRQ) ? (64 + (gpio)) : -EINVAL)
-
-#define irq_to_gpio(irq) ((irq) - gpio_to_irq(0))
-
-#endif
+#endif /* __GPIO_EP93XX_H */
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/gpio.h>
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
#include <mach/hardware.h>
#include <mach/fb.h>
+#include <mach/gpio-ep93xx.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/io.h>
-#include <linux/gpio.h>
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
#include <linux/fb.h>
#include <mach/hardware.h>
#include <mach/fb.h>
+#include <mach/gpio-ep93xx.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#ifndef __ASM_ARCH_GPIO_H
#define __ASM_ARCH_GPIO_H __FILE__
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* Practically, GPIO banks up to GPZ are the configurable gpio banks */
/* GPIO bank sizes */
#define ARCH_NR_GPIOS (EXYNOS4_GPZ(EXYNOS4_GPIO_Z_NR) + \
CONFIG_SAMSUNG_GPIO_EXTRA + 1)
-#include <asm-generic/gpio.h>
-
#endif /* __ASM_ARCH_GPIO_H */
#define PCIO_SIZE 0x00100000
#define PCIO_BASE MMU_IO(0xff000000, 0x7c000000)
-#define IO_SPACE_LIMIT 0xffff
-
/*
* Translation of various region addresses to virtual addresses
*/
#define __MACH_GPIO_H__
#include <mach/irqs.h>
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
#define gpio_to_irq(x) ((x) + GPIO_IRQ_BASE)
#define irq_to_gpio(x) ((x) - GPIO_IRQ_BASE)
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/spinlock.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <mach/hardware.h>
-#include <mach/gpio.h>
#include <mach/iomux-mx3.h>
/*
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
-
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/map.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <mach/iomux-mx27.h>
#include "devices-imx27.h"
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffff
-
/*
* WARNING: this has to mirror definitions in platform.h
*/
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/spinlock.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ixp2000.h>
static DEFINE_SPINLOCK(ixp2000_slowport_lock);
static unsigned long ixp2000_slowport_irq_flags;
*
* Copyright (C) 2002 Intel Corporation.
*
- * This program is free software, you can redistribute it and/or modify
+ * This program is free software, you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/*
* IXP2000 GPIO in/out, edge/level detection for IRQs:
* IRQs are generated on Falling-edge, Rising-Edge, Level-low, Level-High
- * or both Falling-edge and Rising-edge.
+ * or both Falling-edge and Rising-edge.
* This must be called *before* the corresponding IRQ is registerd.
* Use this instead of directly setting the GPIO registers.
* GPIOs may also be used as GPIOs (e.g. for emulating i2c/smb)
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <asm/mach/flash.h>
#include <asm/mach/arch.h>
-#include <mach/gpio.h>
-
+#include <mach/gpio-ixp2000.h>
/*************************************************************************
* IXDP2x00 IRQ Initialization
* Author: Rod Whitby <rod@whitby.id.au>
* Maintainers: http://www.nslu2-linux.org/
*/
-
+#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/jiffies.h>
#include <linux/timer.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/time.h>
-#include <asm/gpio.h>
#define DSMG600_SDA_PIN 5
#define DSMG600_SCL_PIN 4
* Maintainers: http://www.nslu2-linux.org/
*
*/
-
+#include <linux/gpio.h>
#include <linux/if_ether.h>
#include <linux/irq.h>
#include <linux/serial.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
-#include <asm/gpio.h>
#define FSG_SDA_PIN 12
#define FSG_SCL_PIN 13
#include <linux/kernel.h>
#include <mach/hardware.h>
+#define __ARM_GPIOLIB_COMPLEX
+
static inline int gpio_request(unsigned gpio, const char *label)
{
return 0;
#include <asm-generic/gpio.h> /* cansleep wrappers */
extern int gpio_to_irq(int gpio);
+#define gpio_to_irq gpio_to_irq
extern int irq_to_gpio(unsigned int irq);
#endif
#include <mach/hardware.h>
-#define IO_SPACE_LIMIT 0x0000ffff
-
extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data);
extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data);
* Maintainers: http://www.nslu2-linux.org/
*
*/
-
+#include <linux/gpio.h>
#include <linux/if_ether.h>
#include <linux/irq.h>
#include <linux/jiffies.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
-#include <asm/gpio.h>
#define NAS100D_SDA_PIN 5
#define NAS100D_SCL_PIN 6
* Maintainers: http://www.nslu2-linux.org/
*
*/
-
+#include <linux/gpio.h>
#include <linux/if_ether.h>
#include <linux/irq.h>
#include <linux/serial.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/time.h>
-#include <asm/gpio.h>
#define NSLU2_SDA_PIN 7
#define NSLU2_SCL_PIN 6
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/irq.h>
#include <linux/io.h>
#include <mach/bridge-regs.h>
#include <plat/irq.h>
-#include <asm/gpio.h>
#include "common.h"
static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mbus.h>
#include <linux/io.h>
-#include <asm/gpio.h>
#include <mach/hardware.h>
#include <plat/mpp.h>
#include "common.h"
# Makefile for KS8695 architecture support
#
-obj-y := cpu.o irq.o time.o gpio.o devices.o
+obj-y := cpu.o irq.o time.o devices.o
obj-m :=
obj-n :=
obj- :=
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <asm/mach/irq.h>
#include <mach/devices.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
#include "generic.h"
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <asm/mach/irq.h>
#include <mach/devices.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
#include "generic.h"
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
#include <mach/devices.h>
#include "generic.h"
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <mach/irqs.h>
--- /dev/null
+/*
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MACH_KS8659_GPIO_H
+#define __MACH_KS8659_GPIO_H
+
+#include <linux/kernel.h>
+
+#define KS8695_GPIO_0 0
+#define KS8695_GPIO_1 1
+#define KS8695_GPIO_2 2
+#define KS8695_GPIO_3 3
+#define KS8695_GPIO_4 4
+#define KS8695_GPIO_5 5
+#define KS8695_GPIO_6 6
+#define KS8695_GPIO_7 7
+#define KS8695_GPIO_8 8
+#define KS8695_GPIO_9 9
+#define KS8695_GPIO_10 10
+#define KS8695_GPIO_11 11
+#define KS8695_GPIO_12 12
+#define KS8695_GPIO_13 13
+#define KS8695_GPIO_14 14
+#define KS8695_GPIO_15 15
+
+/*
+ * Configure GPIO pin as external interrupt source.
+ */
+extern int ks8695_gpio_interrupt(unsigned int pin, unsigned int type);
+
+/* Register the GPIOs */
+extern void ks8695_register_gpios(void);
+
+#endif /* __MACH_KS8659_GPIO_H */
#ifndef __ASM_ARCH_GPIO_H_
#define __ASM_ARCH_GPIO_H_
-#include <linux/kernel.h>
-
-#define KS8695_GPIO_0 0
-#define KS8695_GPIO_1 1
-#define KS8695_GPIO_2 2
-#define KS8695_GPIO_3 3
-#define KS8695_GPIO_4 4
-#define KS8695_GPIO_5 5
-#define KS8695_GPIO_6 6
-#define KS8695_GPIO_7 7
-#define KS8695_GPIO_8 8
-#define KS8695_GPIO_9 9
-#define KS8695_GPIO_10 10
-#define KS8695_GPIO_11 11
-#define KS8695_GPIO_12 12
-#define KS8695_GPIO_13 13
-#define KS8695_GPIO_14 14
-#define KS8695_GPIO_15 15
-
-/*
- * Configure GPIO pin as external interrupt source.
- */
-extern int ks8695_gpio_interrupt(unsigned int pin, unsigned int type);
-
/*
* Map IRQ number to GPIO line.
*/
extern int irq_to_gpio(unsigned int irq);
-#include <asm-generic/gpio.h>
-
-/* If it turns out that we need to optimise GPIO access for the
- * Micrel's GPIOs, then these can be changed to check their argument
- * directly as static inlines. However for now it's probably not
- * worthwhile.
- */
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_to_irq __gpio_to_irq
-
-/* Register the GPIOs */
-extern void ks8695_register_gpios(void);
-
#endif
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <asm/leds.h>
#include <mach/devices.h>
-#include <mach/gpio.h>
static inline void ks8695_led_on(unsigned int led)
#
obj-y := timer.o irq.o common.o serial.o clock.o
-obj-y += gpiolib.o pm.o suspend.o
+obj-y += pm.o suspend.o
obj-y += phy3250.o
--- /dev/null
+/*
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MACH_GPIO_LPC32XX_H
+#define __MACH_GPIO_LPC32XX_H
+
+/*
+ * Note!
+ * Muxed GP pins need to be setup to the GP state in the board level
+ * code prior to using this driver.
+ * GPI pins : 28xP3 group
+ * GPO pins : 24xP3 group
+ * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group
+ */
+
+#define LPC32XX_GPIO_P0_MAX 8
+#define LPC32XX_GPIO_P1_MAX 24
+#define LPC32XX_GPIO_P2_MAX 13
+#define LPC32XX_GPIO_P3_MAX 6
+#define LPC32XX_GPI_P3_MAX 28
+#define LPC32XX_GPO_P3_MAX 24
+
+#define LPC32XX_GPIO_P0_GRP 0
+#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX)
+#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX)
+#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX)
+#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX)
+#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX)
+
+/*
+ * A specific GPIO can be selected with this macro
+ * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
+ * See the LPC32x0 User's guide for GPIO group numbers
+ */
+#define LPC32XX_GPIO(x, y) ((x) + (y))
+
+#endif /* __MACH_GPIO_LPC32XX_H */
-/*
- * arch/arm/mach-lpc32xx/include/mach/gpio.h
- *
- * Author: Kevin Wells <kevin.wells@nxp.com>
- *
- * Copyright (C) 2010 NXP Semiconductors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
-
-#include <asm-generic/gpio.h>
-
-/*
- * Note!
- * Muxed GP pins need to be setup to the GP state in the board level
- * code prior to using this driver.
- * GPI pins : 28xP3 group
- * GPO pins : 24xP3 group
- * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group
- */
-
-#define LPC32XX_GPIO_P0_MAX 8
-#define LPC32XX_GPIO_P1_MAX 24
-#define LPC32XX_GPIO_P2_MAX 13
-#define LPC32XX_GPIO_P3_MAX 6
-#define LPC32XX_GPI_P3_MAX 28
-#define LPC32XX_GPO_P3_MAX 24
-
-#define LPC32XX_GPIO_P0_GRP 0
-#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX)
-#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX)
-#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX)
-#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX)
-#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX)
-
-/*
- * A specific GPIO can be selected with this macro
- * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
- * See the LPC32x0 User's guide for GPIO group numbers
- */
-#define LPC32XX_GPIO(x, y) ((x) + (y))
-
-static inline int gpio_get_value(unsigned gpio)
-{
- return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
- __gpio_set_value(gpio, value);
-}
-
-static inline int gpio_cansleep(unsigned gpio)
-{
- return __gpio_cansleep(gpio);
-}
-
-static inline int gpio_to_irq(unsigned gpio)
-{
- return __gpio_to_irq(gpio);
-}
-
-#endif
#include <mach/hardware.h>
#include <mach/platform.h>
+#include <mach/gpio-lpc32xx.h>
#include "common.h"
/*
* it under the terms of the GNU General Public License version 2 as
* publishhed by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
#include <linux/interrupt.h>
+#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/addr-map.h>
#include <mach/mfp-pxa168.h>
#include <mach/pxa168.h>
-#include <mach/gpio.h>
#include <video/pxa168fb.h>
#include <linux/input.h>
#include <plat/pxa27x_keypad.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/io.h>
-#include <linux/gpio.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/max8649.h>
#include <linux/regulator/fixed.h>
*/
#include <linux/init.h>
+#include <linux/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
-#include <mach/gpio.h>
#include <mach/pxa168.h>
#include <mach/mfp-pxa168.h>
--- /dev/null
+#ifndef __ASM_MACH_GPIO_PXA_H
+#define __ASM_MACH_GPIO_PXA_H
+
+#include <mach/addr-map.h>
+#include <mach/irqs.h>
+
+#define GPIO_REGS_VIRT (APB_VIRT_BASE + 0x19000)
+
+#define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
+#define GPIO_REG(x) (*((volatile u32 *)(GPIO_REGS_VIRT + (x))))
+
+#define NR_BUILTIN_GPIO IRQ_GPIO_NUM
+
+#define gpio_to_bank(gpio) ((gpio) >> 5)
+
+/* NOTE: these macros are defined here to make optimization of
+ * gpio_{get,set}_value() to work when 'gpio' is a constant.
+ * Usage of these macros otherwise is no longer recommended,
+ * use generic GPIO API whenever possible.
+ */
+#define GPIO_bit(gpio) (1 << ((gpio) & 0x1f))
+
+#define GPLR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x00)
+#define GPDR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x0c)
+#define GPSR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x18)
+#define GPCR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x24)
+
+#include <plat/gpio-pxa.h>
+
+#endif /* __ASM_MACH_GPIO_PXA_H */
#ifndef __ASM_MACH_GPIO_H
#define __ASM_MACH_GPIO_H
-#include <mach/addr-map.h>
-#include <mach/irqs.h>
#include <asm-generic/gpio.h>
-#define GPIO_REGS_VIRT (APB_VIRT_BASE + 0x19000)
-
-#define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
-#define GPIO_REG(x) (*((volatile u32 *)(GPIO_REGS_VIRT + (x))))
-
-#define NR_BUILTIN_GPIO IRQ_GPIO_NUM
-
-#define gpio_to_bank(gpio) ((gpio) >> 5)
#define gpio_to_irq(gpio) (IRQ_GPIO_START + (gpio))
#define irq_to_gpio(irq) ((irq) - IRQ_GPIO_START)
-
#define __gpio_is_inverted(gpio) (0)
#define __gpio_is_occupied(gpio) (0)
-/* NOTE: these macros are defined here to make optimization of
- * gpio_{get,set}_value() to work when 'gpio' is a constant.
- * Usage of these macros otherwise is no longer recommended,
- * use generic GPIO API whenever possible.
- */
-#define GPIO_bit(gpio) (1 << ((gpio) & 0x1f))
-
-#define GPLR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x00)
-#define GPDR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x0c)
-#define GPSR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x18)
-#define GPCR(x) GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x24)
-
#include <plat/gpio.h>
#endif /* __ASM_MACH_GPIO_H */
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/io.h>
-#include <linux/gpio.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/max8649.h>
#include <linux/mfd/max8925.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <mach/irqs.h>
#include <mach/dma.h>
#include <mach/mfp.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
#include <mach/devices.h>
#include <mach/mmp2.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <mach/regs-apbc.h>
#include <mach/regs-apmu.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
#include <mach/dma.h>
#include <mach/devices.h>
#include <mach/mfp.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <mach/regs-apmu.h>
#include <mach/cputype.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
#include <mach/dma.h>
#include <mach/mfp.h>
#include <mach/devices.h>
* it under the terms of the GNU General Public License version 2 as
* publishhed by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/smc91x.h>
+#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/addr-map.h>
#include <mach/mfp-pxa910.h>
#include <mach/pxa910.h>
-#include <mach/gpio.h>
#include "common.h"
* GNU General Public License for more details.
*
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <mach/vreg.h>
#include <mach/mpp.h>
-#include <mach/gpio.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
* 02110-1301, USA.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/irq.h>
#include <linux/gpio.h>
#include <asm/memory.h>
#include <asm/setup.h>
-#include <mach/gpio.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>
#include <mach/dma.h>
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
* 02110-1301, USA.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/irq.h>
#include <linux/gpio.h>
#include <mach/board.h>
#include <mach/irqs.h>
#include <mach/sirc.h>
-#include <mach/gpio.h>
#include <mach/vreg.h>
#include <mach/mmc.h>
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
-#include <asm/gpio.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
/* linux/arch/arm/mach-msm/board-trout-mmc.c
** Author: Brian Swetland <swetland@google.com>
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/err.h>
#include <linux/debugfs.h>
-#include <asm/gpio.h>
#include <asm/io.h>
#include <mach/vreg.h>
/* linux/arch/arm/mach-msm/board-trout-mddi.c
** Author: Brian Swetland <swetland@google.com>
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/err.h>
#include <asm/io.h>
-#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <mach/msm_fb.h>
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2009-2010, Code Aurora Forum. All rights reserved.
- * Author: Mike Lockwood <lockwood@android.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-#ifndef __ASM_ARCH_MSM_GPIO_H
-#define __ASM_ARCH_MSM_GPIO_H
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
-#endif /* __ASM_ARCH_MSM_GPIO_H */
+/* empty */
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/irq.h>
-#include <asm/gpio.h>
#include <mach/bridge-regs.h>
#include <plat/irq.h>
#include "common.h"
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mbus.h>
#include <linux/io.h>
#include <plat/mpp.h>
-#include <asm/gpio.h>
#include <mach/hardware.h>
#include "common.h"
#include "mpp.h"
#ifndef __MACH_MXS_GPIO_H__
#define __MACH_MXS_GPIO_H__
-#include <asm-generic/gpio.h>
-
#define MXS_GPIO_NR(bank, nr) ((bank) * 32 + (nr))
-/* use gpiolib dispatchers */
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
#define irq_to_gpio(irq) ((irq) - MXS_GPIO_IRQ_START)
#endif /* __MACH_MXS_GPIO_H__ */
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>
+#include <plat/gpio-nomadik.h>
#include <plat/mtu.h>
#include <mach/setup.h>
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/platform_device.h>
-#include <linux/gpio.h>
+#include <plat/gpio-nomadik.h>
#include <mach/hardware.h>
#include <mach/irqs.h>
#include <asm/mach/map.h>
#include <linux/i2c.h>
#include <linux/i2c-algo-bit.h>
#include <linux/i2c-gpio.h>
-#include <linux/gpio.h>
#include <linux/platform_device.h>
+#include <plat/gpio-nomadik.h>
/*
* There are two busses in the 8815NHK.
#ifndef __ASM_ARCH_GPIO_H
#define __ASM_ARCH_GPIO_H
-#include <plat/gpio.h>
-
#endif /* __ASM_ARCH_GPIO_H */
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/input.h>
#include <plat/io.h>
#include <plat/board-ams-delta.h>
-#include <mach/gpio.h>
#include <plat/keypad.h>
#include <plat/mux.h>
#include <plat/usb.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/map.h>
#include <plat/tc.h>
-#include <mach/gpio.h>
#include <plat/mux.h>
#include <plat/flash.h>
#include <plat/fpga.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/mux.h>
#include <plat/usb.h>
#include <plat/board.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c/tps65010.h>
#include <plat/mmc.h>
-#include <mach/gpio.h>
#include "board-h2.h"
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/smc91x.h>
#include <mach/hardware.h>
-#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c/tps65010.h>
#include <plat/mmc.h>
-#include <mach/gpio.h>
#include "board-h3.h"
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/types.h>
#include <linux/init.h>
#include <linux/major.h>
#include <asm/setup.h>
#include <asm/page.h>
#include <mach/hardware.h>
-#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
* 02110-1301, USA.
*
*/
-
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <plat/mux.h>
#include <plat/flash.h>
#include <plat/fpga.h>
-#include <mach/gpio.h>
#include <plat/tc.h>
#include <plat/usb.h>
#include <plat/keypad.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mutex.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/mux.h>
#include <plat/usb.h>
#include <plat/board.h>
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c/tps65010.h>
#include <mach/hardware.h>
-#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/input.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/usb.h>
*/
#include <linux/delay.h>
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/map.h>
#include <plat/led.h>
-#include <mach/gpio.h>
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/usb.h>
*/
#include <linux/delay.h>
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/usb.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/map.h>
#include <plat/tc.h>
-#include <mach/gpio.h>
#include <plat/mux.h>
#include <plat/fpga.h>
#include <plat/flash.h>
* published by the Free Software Foundation.
*/
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <mach/hardware.h>
#include <plat/mmc.h>
-#include <mach/gpio.h>
#include <plat/board-sx1.h>
#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/input.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/dma.h>
*/
#include <linux/delay.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <plat/board-voiceblue.h>
#include <plat/common.h>
-#include <mach/gpio.h>
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/tc.h>
*/
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <plat/tc.h>
#include <plat/board.h>
#include <plat/mux.h>
-#include <mach/gpio.h>
#include <plat/mmc.h>
#include <plat/omap7xx.h>
#include <plat/mcbsp.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/device.h>
#include <asm/mach/irq.h>
#include <plat/fpga.h>
-#include <mach/gpio.h>
static void fpga_mask_irq(struct irq_data *d)
{
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/sched.h>
#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
-#include <mach/gpio.h>
#include <plat/cpu.h>
#define IRQ_BANK(irq) ((irq) >> 5)
* The "surfer" expansion board and H2 sample board also have two-color
* green+red LEDs (in parallel), used here for timer and idle indicators.
*/
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/kernel_stat.h>
#include <linux/sched.h>
#include <asm/mach-types.h>
#include <plat/fpga.h>
-#include <mach/gpio.h>
#include "leds.h"
*
* LED driver for OSK with optional Mistral QVGA board
*/
+#include <linux/gpio.h>
#include <linux/init.h>
#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
-#include <mach/gpio.h>
-
#include "leds.h"
*
* OMAP LEDs dispatcher
*/
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/leds.h>
#include <asm/mach-types.h>
-#include <mach/gpio.h>
#include <plat/mux.h>
#include "leds.h"
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <plat/board.h>
#include <plat/mux.h>
-#include <mach/gpio.h>
#include <plat/fpga.h>
#include "pm.h"
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/device.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/usb.h>
#include <plat/board.h>
#include <plat/common.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/usb.h>
#include <plat/board.h>
#include <plat/common.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/map.h>
#include <plat/mcspi.h>
-#include <mach/gpio.h>
#include <plat/board.h>
#include <plat/common.h>
#include <plat/gpmc.h>
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <plat/tc.h>
#include <plat/board.h>
#include <plat/mcbsp.h>
-#include <mach/gpio.h>
#include <plat/mmc.h>
#include <plat/dma.h>
#include <plat/omap_hwmod.h>
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mv643xx_eth.h>
#include <linux/i2c.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
* License, or (at your option) any later version.
*
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/phy.h>
#include <linux/marvell_phy.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/irq.h>
#include <linux/io.h>
-#include <asm/gpio.h>
#include <mach/bridge-regs.h>
#include <plat/irq.h>
#include "common.h"
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/serial_reg.h>
#include <linux/ata_platform.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/ata_platform.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <mach/orion5x.h>
#include "common.h"
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/ethtool.h>
#include <net/dsa.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/leds.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <net/dsa.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/leds.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/ata_platform.h>
#include <linux/i2c.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/leds.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/ethtool.h>
#include <net/dsa.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/leds.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/serial_reg.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/serial_reg.h>
#include <linux/ata_platform.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/serial_reg.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/ethtool.h>
#include <net/dsa.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/input.h>
#include <net/dsa.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
-
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <mach/platform.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pnx4008.h>
/* register definitions */
#define PIO_VA_BASE IO_ADDRESS(PNX4008_PIO_BASE)
/*
- * arch/arm/mach-pnx4008/include/mach/gpio.h
+ * arch/arm/mach-pnx4008/include/mach/gpio-pnx4008.h
*
* PNX4008 GPIO driver - header file
*
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/io.h>
#include <linux/serial_core.h>
#include <linux/serial_reg.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pnx4008.h>
#include <mach/clock.h>
#define UART_3 0
#include <linux/platform_device.h>
#include <linux/irq.h>
-#include <linux/gpio.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/nand-gpio.h>
* initialization stuff for PXA machines which can be overridden later if
* need be.
*/
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/mach-types.h>
#include <mach/reset.h>
-#include <mach/gpio.h>
#include <mach/smemc.h>
#include <mach/pxa3xx-regs.h>
--- /dev/null
+/*
+ * Written by Philipp Zabel <philipp.zabel@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+#ifndef __MACH_PXA_GPIO_PXA_H
+#define __MACH_PXA_GPIO_PXA_H
+
+#include <mach/irqs.h>
+#include <mach/hardware.h>
+
+#define GPIO_REGS_VIRT io_p2v(0x40E00000)
+
+#define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
+#define GPIO_REG(x) (*(volatile u32 *)(GPIO_REGS_VIRT + (x)))
+
+/* GPIO Pin Level Registers */
+#define GPLR0 GPIO_REG(BANK_OFF(0) + 0x00)
+#define GPLR1 GPIO_REG(BANK_OFF(1) + 0x00)
+#define GPLR2 GPIO_REG(BANK_OFF(2) + 0x00)
+#define GPLR3 GPIO_REG(BANK_OFF(3) + 0x00)
+
+/* GPIO Pin Direction Registers */
+#define GPDR0 GPIO_REG(BANK_OFF(0) + 0x0c)
+#define GPDR1 GPIO_REG(BANK_OFF(1) + 0x0c)
+#define GPDR2 GPIO_REG(BANK_OFF(2) + 0x0c)
+#define GPDR3 GPIO_REG(BANK_OFF(3) + 0x0c)
+
+/* GPIO Pin Output Set Registers */
+#define GPSR0 GPIO_REG(BANK_OFF(0) + 0x18)
+#define GPSR1 GPIO_REG(BANK_OFF(1) + 0x18)
+#define GPSR2 GPIO_REG(BANK_OFF(2) + 0x18)
+#define GPSR3 GPIO_REG(BANK_OFF(3) + 0x18)
+
+/* GPIO Pin Output Clear Registers */
+#define GPCR0 GPIO_REG(BANK_OFF(0) + 0x24)
+#define GPCR1 GPIO_REG(BANK_OFF(1) + 0x24)
+#define GPCR2 GPIO_REG(BANK_OFF(2) + 0x24)
+#define GPCR3 GPIO_REG(BANK_OFF(3) + 0x24)
+
+/* GPIO Rising Edge Detect Registers */
+#define GRER0 GPIO_REG(BANK_OFF(0) + 0x30)
+#define GRER1 GPIO_REG(BANK_OFF(1) + 0x30)
+#define GRER2 GPIO_REG(BANK_OFF(2) + 0x30)
+#define GRER3 GPIO_REG(BANK_OFF(3) + 0x30)
+
+/* GPIO Falling Edge Detect Registers */
+#define GFER0 GPIO_REG(BANK_OFF(0) + 0x3c)
+#define GFER1 GPIO_REG(BANK_OFF(1) + 0x3c)
+#define GFER2 GPIO_REG(BANK_OFF(2) + 0x3c)
+#define GFER3 GPIO_REG(BANK_OFF(3) + 0x3c)
+
+/* GPIO Edge Detect Status Registers */
+#define GEDR0 GPIO_REG(BANK_OFF(0) + 0x48)
+#define GEDR1 GPIO_REG(BANK_OFF(1) + 0x48)
+#define GEDR2 GPIO_REG(BANK_OFF(2) + 0x48)
+#define GEDR3 GPIO_REG(BANK_OFF(3) + 0x48)
+
+/* GPIO Alternate Function Select Registers */
+#define GAFR0_L GPIO_REG(0x0054)
+#define GAFR0_U GPIO_REG(0x0058)
+#define GAFR1_L GPIO_REG(0x005C)
+#define GAFR1_U GPIO_REG(0x0060)
+#define GAFR2_L GPIO_REG(0x0064)
+#define GAFR2_U GPIO_REG(0x0068)
+#define GAFR3_L GPIO_REG(0x006C)
+#define GAFR3_U GPIO_REG(0x0070)
+
+/* More handy macros. The argument is a literal GPIO number. */
+
+#define GPIO_bit(x) (1 << ((x) & 0x1f))
+
+#define GPLR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x00)
+#define GPDR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x0c)
+#define GPSR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x18)
+#define GPCR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x24)
+#define GRER(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x30)
+#define GFER(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x3c)
+#define GEDR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x48)
+#define GAFR(x) GPIO_REG(0x54 + (((x) & 0x70) >> 2))
+
+
+#define NR_BUILTIN_GPIO PXA_GPIO_IRQ_NUM
+
+#define gpio_to_bank(gpio) ((gpio) >> 5)
+
+#ifdef CONFIG_CPU_PXA26x
+/* GPIO86/87/88/89 on PXA26x have their direction bits in GPDR2 inverted,
+ * as well as their Alternate Function value being '1' for GPIO in GAFRx.
+ */
+static inline int __gpio_is_inverted(unsigned gpio)
+{
+ return cpu_is_pxa25x() && gpio > 85;
+}
+#else
+static inline int __gpio_is_inverted(unsigned gpio) { return 0; }
+#endif
+
+/*
+ * On PXA25x and PXA27x, GAFRx and GPDRx together decide the alternate
+ * function of a GPIO, and GPDRx cannot be altered once configured. It
+ * is attributed as "occupied" here (I know this terminology isn't
+ * accurate, you are welcome to propose a better one :-)
+ */
+static inline int __gpio_is_occupied(unsigned gpio)
+{
+ if (cpu_is_pxa27x() || cpu_is_pxa25x()) {
+ int af = (GAFR(gpio) >> ((gpio & 0xf) * 2)) & 0x3;
+ int dir = GPDR(gpio) & GPIO_bit(gpio);
+
+ if (__gpio_is_inverted(gpio))
+ return af != 1 || dir == 0;
+ else
+ return af != 0 || dir != 0;
+ } else
+ return GPDR(gpio) & GPIO_bit(gpio);
+}
+
+#include <plat/gpio-pxa.h>
+#endif /* __MACH_PXA_GPIO_PXA_H */
#ifndef __ASM_ARCH_PXA_GPIO_H
#define __ASM_ARCH_PXA_GPIO_H
-#include <mach/irqs.h>
-#include <mach/hardware.h>
#include <asm-generic/gpio.h>
+/* The defines for the driver are needed for the accelerated accessors */
+#include "gpio-pxa.h"
-#define GPIO_REGS_VIRT io_p2v(0x40E00000)
-
-#define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
-#define GPIO_REG(x) (*(volatile u32 *)(GPIO_REGS_VIRT + (x)))
-
-/* GPIO Pin Level Registers */
-#define GPLR0 GPIO_REG(BANK_OFF(0) + 0x00)
-#define GPLR1 GPIO_REG(BANK_OFF(1) + 0x00)
-#define GPLR2 GPIO_REG(BANK_OFF(2) + 0x00)
-#define GPLR3 GPIO_REG(BANK_OFF(3) + 0x00)
-
-/* GPIO Pin Direction Registers */
-#define GPDR0 GPIO_REG(BANK_OFF(0) + 0x0c)
-#define GPDR1 GPIO_REG(BANK_OFF(1) + 0x0c)
-#define GPDR2 GPIO_REG(BANK_OFF(2) + 0x0c)
-#define GPDR3 GPIO_REG(BANK_OFF(3) + 0x0c)
-
-/* GPIO Pin Output Set Registers */
-#define GPSR0 GPIO_REG(BANK_OFF(0) + 0x18)
-#define GPSR1 GPIO_REG(BANK_OFF(1) + 0x18)
-#define GPSR2 GPIO_REG(BANK_OFF(2) + 0x18)
-#define GPSR3 GPIO_REG(BANK_OFF(3) + 0x18)
-
-/* GPIO Pin Output Clear Registers */
-#define GPCR0 GPIO_REG(BANK_OFF(0) + 0x24)
-#define GPCR1 GPIO_REG(BANK_OFF(1) + 0x24)
-#define GPCR2 GPIO_REG(BANK_OFF(2) + 0x24)
-#define GPCR3 GPIO_REG(BANK_OFF(3) + 0x24)
-
-/* GPIO Rising Edge Detect Registers */
-#define GRER0 GPIO_REG(BANK_OFF(0) + 0x30)
-#define GRER1 GPIO_REG(BANK_OFF(1) + 0x30)
-#define GRER2 GPIO_REG(BANK_OFF(2) + 0x30)
-#define GRER3 GPIO_REG(BANK_OFF(3) + 0x30)
-
-/* GPIO Falling Edge Detect Registers */
-#define GFER0 GPIO_REG(BANK_OFF(0) + 0x3c)
-#define GFER1 GPIO_REG(BANK_OFF(1) + 0x3c)
-#define GFER2 GPIO_REG(BANK_OFF(2) + 0x3c)
-#define GFER3 GPIO_REG(BANK_OFF(3) + 0x3c)
-
-/* GPIO Edge Detect Status Registers */
-#define GEDR0 GPIO_REG(BANK_OFF(0) + 0x48)
-#define GEDR1 GPIO_REG(BANK_OFF(1) + 0x48)
-#define GEDR2 GPIO_REG(BANK_OFF(2) + 0x48)
-#define GEDR3 GPIO_REG(BANK_OFF(3) + 0x48)
-
-/* GPIO Alternate Function Select Registers */
-#define GAFR0_L GPIO_REG(0x0054)
-#define GAFR0_U GPIO_REG(0x0058)
-#define GAFR1_L GPIO_REG(0x005C)
-#define GAFR1_U GPIO_REG(0x0060)
-#define GAFR2_L GPIO_REG(0x0064)
-#define GAFR2_U GPIO_REG(0x0068)
-#define GAFR3_L GPIO_REG(0x006C)
-#define GAFR3_U GPIO_REG(0x0070)
-
-/* More handy macros. The argument is a literal GPIO number. */
-
-#define GPIO_bit(x) (1 << ((x) & 0x1f))
-
-#define GPLR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x00)
-#define GPDR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x0c)
-#define GPSR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x18)
-#define GPCR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x24)
-#define GRER(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x30)
-#define GFER(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x3c)
-#define GEDR(x) GPIO_REG(BANK_OFF((x) >> 5) + 0x48)
-#define GAFR(x) GPIO_REG(0x54 + (((x) & 0x70) >> 2))
-
-
-#define NR_BUILTIN_GPIO PXA_GPIO_IRQ_NUM
-
-#define gpio_to_bank(gpio) ((gpio) >> 5)
#define gpio_to_irq(gpio) IRQ_GPIO(gpio)
static inline int irq_to_gpio(unsigned int irq)
return -1;
}
-#ifdef CONFIG_CPU_PXA26x
-/* GPIO86/87/88/89 on PXA26x have their direction bits in GPDR2 inverted,
- * as well as their Alternate Function value being '1' for GPIO in GAFRx.
- */
-static inline int __gpio_is_inverted(unsigned gpio)
-{
- return cpu_is_pxa25x() && gpio > 85;
-}
-#else
-static inline int __gpio_is_inverted(unsigned gpio) { return 0; }
-#endif
-
-/*
- * On PXA25x and PXA27x, GAFRx and GPDRx together decide the alternate
- * function of a GPIO, and GPDRx cannot be altered once configured. It
- * is attributed as "occupied" here (I know this terminology isn't
- * accurate, you are welcome to propose a better one :-)
- */
-static inline int __gpio_is_occupied(unsigned gpio)
-{
- if (cpu_is_pxa27x() || cpu_is_pxa25x()) {
- int af = (GAFR(gpio) >> ((gpio & 0xf) * 2)) & 0x3;
- int dir = GPDR(gpio) & GPIO_bit(gpio);
-
- if (__gpio_is_inverted(gpio))
- return af != 1 || dir == 0;
- else
- return af != 0 || dir != 0;
- } else
- return GPDR(gpio) & GPIO_bit(gpio);
-}
-
#include <plat/gpio.h>
#endif
#ifndef __ASM_ARCH_LITTLETON_H
#define __ASM_ARCH_LITTLETON_H
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
#define LITTLETON_ETH_PHYS 0x30000000
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
#include <linux/init.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <mach/hardware.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
#include "generic.h"
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/syscore_ops.h>
#include <asm/mach/flash.h>
#include <mach/pxa27x.h>
-#include <mach/gpio.h>
#include <mach/lpd270.h>
#include <mach/audio.h>
#include <mach/pxafb.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/hardware/sa1111.h>
#include <mach/pxa25x.h>
-#include <mach/gpio.h>
#include <mach/audio.h>
#include <mach/lubbock.h>
#include <mach/udc.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/syscore_ops.h>
#include <asm/mach/flash.h>
#include <mach/pxa27x.h>
-#include <mach/gpio.h>
#include <mach/mainstone.h>
#include <mach/audio.h>
#include <mach/pxafb.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/syscore_ops.h>
-#include <mach/gpio.h>
#include <mach/pxa2xx-regs.h>
#include <mach/mfp-pxa2xx.h>
+#include <mach/gpio-pxa.h>
#include "generic.h"
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <media/soc_camera.h>
-#include <asm/gpio.h>
#include <mach/camera.h>
#include <asm/mach/map.h>
#include <mach/pxa27x.h>
* initialization stuff for PXA machines which can be overridden later if
* need be.
*/
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/suspend.h>
#include <linux/syscore_ops.h>
#include <linux/irq.h>
+#include <linux/gpio.h>
#include <asm/mach/map.h>
#include <asm/suspend.h>
#include <mach/hardware.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
#include <mach/pxa25x.h>
#include <mach/reset.h>
#include <mach/pm.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/i2c/pxa-i2c.h>
+#include <linux/gpio.h>
#include <asm/mach/map.h>
#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/suspend.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
#include <mach/pxa27x.h>
#include <mach/reset.h>
#include <mach/ohci.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/mach/map.h>
#include <asm/suspend.h>
#include <mach/hardware.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
#include <mach/pxa3xx-regs.h>
#include <mach/reset.h>
#include <mach/ohci.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/syscore_ops.h>
#include <mach/hardware.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pxa.h>
#include <mach/pxa3xx-regs.h>
#include <mach/pxa930.h>
#include <mach/reset.h>
* it under the terms of the GNU General Public License version 2 as
* publishhed by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/i2c.h>
#include <linux/i2c/pxa-i2c.h>
#include <linux/mfd/88pm860x.h>
+#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/hardware.h>
#include <mach/mfp.h>
#include <mach/mfp-pxa930.h>
-#include <mach/gpio.h>
#include "generic.h"
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
+/* empty */
#define EASI_SIZE 0x08000000 /* EASI I/O */
#define EASI_START 0x08000000
-#define EASI_BASE 0xe5000000
+#define EASI_BASE IOMEM(0xe5000000)
#define IO_START 0x03000000 /* I/O */
#define IO_SIZE 0x01000000
/*
* IO Addresses
*/
-#define VIDC_BASE IOMEM(0xe0400000)
-#define EXPMASK_BASE 0xe0360000
-#define IOMD_BASE IOMEM(0xe0200000)
-#define IOC_BASE IOMEM(0xe0200000)
-#define PCIO_BASE IOMEM(0xe0010000)
-#define FLOPPYDMA_BASE IOMEM(0xe002a000)
+#define ECARD_EASI_BASE (EASI_BASE)
+#define VIDC_BASE (IO_BASE + 0x00400000)
+#define EXPMASK_BASE (IO_BASE + 0x00360000)
+#define ECARD_IOC4_BASE (IO_BASE + 0x00270000)
+#define ECARD_IOC_BASE (IO_BASE + 0x00240000)
+#define IOMD_BASE (IO_BASE + 0x00200000)
+#define IOC_BASE (IO_BASE + 0x00200000)
+#define ECARD_MEMC8_BASE (IO_BASE + 0x0002b000)
+#define FLOPPYDMA_BASE (IO_BASE + 0x0002a000)
+#define PCIO_BASE (IO_BASE + 0x00010000)
+#define ECARD_MEMC_BASE (IO_BASE + 0x00000000)
#define vidc_writel(val) __raw_writel(val, VIDC_BASE)
-#define IO_EC_EASI_BASE 0x81400000
-#define IO_EC_IOC4_BASE 0x8009c000
-#define IO_EC_IOC_BASE 0x80090000
-#define IO_EC_MEMC8_BASE 0x8000ac00
-#define IO_EC_MEMC_BASE 0x80000000
-
#define NETSLOT_BASE 0x0302b000
#define NETSLOT_SIZE 0x00001000
#include <mach/hardware.h>
-#define IO_SPACE_LIMIT 0xffffffff
+#define IO_SPACE_LIMIT 0xffff
/*
- * We use two different types of addressing - PC style addresses, and ARM
- * addresses. PC style accesses the PC hardware with the normal PC IO
- * addresses, eg 0x3f8 for serial#1. ARM addresses are 0x80000000+
- * and are translated to the start of IO. Note that all addresses are
- * shifted left!
- */
-#define __PORT_PCIO(x) (!((x) & 0x80000000))
-
-/*
- * Dynamic IO functions.
- */
-static inline void __outb (unsigned int value, unsigned int port)
-{
- unsigned long temp;
- __asm__ __volatile__(
- "tst %2, #0x80000000\n\t"
- "mov %0, %4\n\t"
- "addeq %0, %0, %3\n\t"
- "strb %1, [%0, %2, lsl #2] @ outb"
- : "=&r" (temp)
- : "r" (value), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
- : "cc");
-}
-
-static inline void __outw (unsigned int value, unsigned int port)
-{
- unsigned long temp;
- __asm__ __volatile__(
- "tst %2, #0x80000000\n\t"
- "mov %0, %4\n\t"
- "addeq %0, %0, %3\n\t"
- "str %1, [%0, %2, lsl #2] @ outw"
- : "=&r" (temp)
- : "r" (value|value<<16), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
- : "cc");
-}
-
-static inline void __outl (unsigned int value, unsigned int port)
-{
- unsigned long temp;
- __asm__ __volatile__(
- "tst %2, #0x80000000\n\t"
- "mov %0, %4\n\t"
- "addeq %0, %0, %3\n\t"
- "str %1, [%0, %2, lsl #2] @ outl"
- : "=&r" (temp)
- : "r" (value), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
- : "cc");
-}
-
-#define DECLARE_DYN_IN(sz,fnsuffix,instr) \
-static inline unsigned sz __in##fnsuffix (unsigned int port) \
-{ \
- unsigned long temp, value; \
- __asm__ __volatile__( \
- "tst %2, #0x80000000\n\t" \
- "mov %0, %4\n\t" \
- "addeq %0, %0, %3\n\t" \
- "ldr" instr " %1, [%0, %2, lsl #2] @ in" #fnsuffix \
- : "=&r" (temp), "=r" (value) \
- : "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE) \
- : "cc"); \
- return (unsigned sz)value; \
-}
-
-static inline void __iomem *__deprecated __ioaddr(unsigned int port)
-{
- void __iomem *ret;
- if (__PORT_PCIO(port))
- ret = PCIO_BASE;
- else
- ret = IO_BASE;
- return ret + (port << 2);
-}
-
-#define DECLARE_IO(sz,fnsuffix,instr) \
- DECLARE_DYN_IN(sz,fnsuffix,instr)
-
-DECLARE_IO(char,b,"b")
-DECLARE_IO(short,w,"")
-DECLARE_IO(int,l,"")
-
-#undef DECLARE_IO
-#undef DECLARE_DYN_IN
-
-/*
- * Constant address IO functions
+ * We need PC style IO addressing for:
+ * - floppy (at 0x3f2,0x3f4,0x3f5,0x3f7)
+ * - parport (at 0x278-0x27a, 0x27b-0x27f, 0x778-0x77a)
+ * - 8250 serial (only for compile)
*
- * These have to be macros for the 'J' constraint to work -
- * +/-4096 immediate operand.
+ * These peripherals are found in an area of MMIO which looks very much
+ * like an ISA bus, but with registers at the low byte of each word.
*/
-#define __outbc(value,port) \
-({ \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "strb %0, [%1, %2] @ outbc" \
- : : "r" (value), "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "strb %0, [%1, %2] @ outbc" \
- : : "r" (value), "r" (IO_BASE), "r" ((port) << 2)); \
-})
-
-#define __inbc(port) \
-({ \
- unsigned char result; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "ldrb %0, [%1, %2] @ inbc" \
- : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "ldrb %0, [%1, %2] @ inbc" \
- : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \
- result; \
-})
-
-#define __outwc(value,port) \
-({ \
- unsigned long __v = value; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outwc" \
- : : "r" (__v|__v<<16), "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outwc" \
- : : "r" (__v|__v<<16), "r" (IO_BASE), "r" ((port) << 2)); \
-})
-
-#define __inwc(port) \
-({ \
- unsigned short result; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inwc" \
- : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inwc" \
- : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \
- result & 0xffff; \
-})
-
-#define __outlc(value,port) \
-({ \
- unsigned long __v = value; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outlc" \
- : : "r" (__v), "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outlc" \
- : : "r" (__v), "r" (IO_BASE), "r" ((port) << 2)); \
-})
-
-#define __inlc(port) \
-({ \
- unsigned long result; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inlc" \
- : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inlc" \
- : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \
- result; \
-})
-
-#define inb(p) (__builtin_constant_p((p)) ? __inbc(p) : __inb(p))
-#define inw(p) (__builtin_constant_p((p)) ? __inwc(p) : __inw(p))
-#define inl(p) (__builtin_constant_p((p)) ? __inlc(p) : __inl(p))
-#define outb(v,p) (__builtin_constant_p((p)) ? __outbc(v,p) : __outb(v,p))
-#define outw(v,p) (__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p))
-#define outl(v,p) (__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p))
-
-/* the following macro is deprecated */
-#define ioaddr(port) ((unsigned long)__ioaddr((port)))
-
-#define insb(p,d,l) __raw_readsb(__ioaddr(p),d,l)
-#define insw(p,d,l) __raw_readsw(__ioaddr(p),d,l)
-
-#define outsb(p,d,l) __raw_writesb(__ioaddr(p),d,l)
-#define outsw(p,d,l) __raw_writesw(__ioaddr(p),d,l)
+#define __io(a) (PCIO_BASE + ((a) << 2))
/*
* 1:1 mapping for ioremapped regions.
.length = IO_SIZE ,
.type = MT_DEVICE
}, { /* EASI space */
- .virtual = EASI_BASE,
+ .virtual = (unsigned long)EASI_BASE,
.pfn = __phys_to_pfn(EASI_START),
.length = EASI_SIZE,
.type = MT_DEVICE
* published by the Free Software Foundation.
*/
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* some boards require extra gpio capacity to support external
* devices that need GPIO.
*/
#define ARCH_NR_GPIOS (256 + CONFIG_S3C24XX_GPIO_EXTRA)
#endif
-#include <asm-generic/gpio.h>
#include <mach/gpio-nrs.h>
#include <mach/gpio-fns.h>
#ifndef __ASM_ARCH_H1940_LATCH_H
#define __ASM_ARCH_H1940_LATCH_H
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#define H1940_LATCH_GPIO(x) (S3C_GPIO_END + (x))
#define outw(v,p) (__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p))
#define outl(v,p) (__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p))
#define __ioaddr(p) (__builtin_constant_p((p)) ? __ioaddr(p) : __ioaddrc(p))
-/* the following macro is deprecated */
-#define ioaddr(port) __ioaddr((port))
#define insb(p,d,l) __raw_readsb(__ioaddr(p),d,l)
#define insw(p,d,l) __raw_readsw(__ioaddr(p),d,l)
* published by the Free Software Foundation.
*/
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* GPIO bank sizes */
#define S3C64XX_GPIO_A_NR (8)
#define S3C64XX_GPIO_B_NR (7)
#define BOARD_NR_GPIOS 16
#define ARCH_NR_GPIOS (GPIO_BOARD_START + BOARD_NR_GPIOS)
-
-#include <asm-generic/gpio.h>
#ifndef __ASM_ARCH_GPIO_H
#define __ASM_ARCH_GPIO_H __FILE__
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* GPIO bank sizes */
#define S5P6440_GPIO_A_NR (6)
#define ARCH_NR_GPIOS (S5P64X0_GPIO_END + CONFIG_SAMSUNG_GPIO_EXTRA)
-#include <asm-generic/gpio.h>
-
#endif /* __ASM_ARCH_GPIO_H */
#ifndef __ASM_ARCH_GPIO_H
#define __ASM_ARCH_GPIO_H __FILE__
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* GPIO bank sizes */
#define S5PC100_GPIO_A0_NR (8)
#define S5PC100_GPIO_A1_NR (5)
/* define the number of gpios we need to the one after the MP04() range */
#define ARCH_NR_GPIOS (S5PC100_GPIO_END + 1)
-#include <asm-generic/gpio.h>
-
#endif /* __ASM_ARCH_GPIO_H */
#ifndef __ASM_ARCH_GPIO_H
#define __ASM_ARCH_GPIO_H __FILE__
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* Practically, GPIO banks up to MP03 are the configurable gpio banks */
/* GPIO bank sizes */
#define ARCH_NR_GPIOS (S5PV210_MP05(S5PV210_GPIO_MP05_NR) + \
CONFIG_SAMSUNG_GPIO_EXTRA + 1)
-#include <asm-generic/gpio.h>
-
#endif /* __ASM_ARCH_GPIO_H */
#
# Common support
-obj-y := clock.o generic.o gpio.o irq.o dma.o time.o #nmi-oopser.o
+obj-y := clock.o generic.o irq.o dma.o time.o #nmi-oopser.o
obj-m :=
obj-n :=
obj- :=
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
#include <asm/irq.h>
-#include <asm/gpio.h>
#include "generic.h"
#include <asm/irq.h>
#include <asm-generic/gpio.h>
+#define __ARM_GPIOLIB_COMPLEX
+
static inline int gpio_get_value(unsigned gpio)
{
if (__builtin_constant_p(gpio) && (gpio <= GPIO_MAX))
#define gpio_to_irq(gpio) ((gpio < 11) ? (IRQ_GPIO0 + gpio) : \
(IRQ_GPIO11 - 11 + gpio))
-#define irq_to_gpio(irq) ((irq < IRQ_GPIO11_27) ? (irq - IRQ_GPIO0) : \
- (irq - IRQ_GPIO11 + 11))
#endif
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffffffff
-
/*
- * We don't actually have real ISA nor PCI buses, but there is so many
- * drivers out there that might just work if we fake them...
+ * __io() is required to be an equivalent mapping to __mem_pci() for
+ * SOC_COMMON to work.
*/
#define __io(a) __typesafe_io(a)
#define __mem_pci(a) (a)
#ifdef CONFIG_GPIOLIB
-static inline int gpio_get_value(unsigned gpio)
-{
- return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
- __gpio_set_value(gpio, value);
-}
-
-static inline int gpio_cansleep(unsigned gpio)
-{
- return __gpio_cansleep(gpio);
-}
-
-static inline int gpio_to_irq(unsigned gpio)
-{
- return __gpio_to_irq(gpio);
-}
-
static inline int irq_to_gpio(unsigned int irq)
{
return -ENOSYS;
}
+#else
+
+#define __ARM_GPIOLIB_COMPLEX
+
#endif /* CONFIG_GPIOLIB */
#endif /* __ASM_ARCH_GPIO_H */
#include <mach/pinmux.h>
#include "board.h"
+#include "board-harmony.h"
#ifdef CONFIG_TEGRA_PCI
-/* GPIO 3 of the PMIC */
-#define EN_VDD_1V05_GPIO (TEGRA_NR_GPIOS + 2)
-
static int __init harmony_pcie_init(void)
{
struct regulator *regulator = NULL;
if (!machine_is_harmony())
return 0;
- err = gpio_request(EN_VDD_1V05_GPIO, "EN_VDD_1V05");
+ err = gpio_request(TEGRA_GPIO_EN_VDD_1V05_GPIO, "EN_VDD_1V05");
if (err)
return err;
- gpio_direction_output(EN_VDD_1V05_GPIO, 1);
+ gpio_direction_output(TEGRA_GPIO_EN_VDD_1V05_GPIO, 1);
regulator = regulator_get(NULL, "pex_clk");
if (IS_ERR_OR_NULL(regulator))
regulator_disable(regulator);
regulator_put(regulator);
err_reg:
- gpio_free(EN_VDD_1V05_GPIO);
+ gpio_free(TEGRA_GPIO_EN_VDD_1V05_GPIO);
return err;
}
#ifndef _MACH_TEGRA_BOARD_HARMONY_H
#define _MACH_TEGRA_BOARD_HARMONY_H
+#include <mach/gpio-tegra.h>
+
#define HARMONY_GPIO_TPS6586X(_x_) (TEGRA_NR_GPIOS + (_x_))
#define HARMONY_GPIO_WM8903(_x_) (HARMONY_GPIO_TPS6586X(4) + (_x_))
#define TEGRA_GPIO_HP_DET TEGRA_GPIO_PW2
#define TEGRA_GPIO_INT_MIC_EN TEGRA_GPIO_PX0
#define TEGRA_GPIO_EXT_MIC_EN TEGRA_GPIO_PX1
+#define TEGRA_GPIO_EN_VDD_1V05_GPIO HARMONY_GPIO_TPS6586X(2)
void harmony_pinmux_init(void);
int harmony_regulator_init(void);
#ifndef _MACH_TEGRA_BOARD_PAZ00_H
#define _MACH_TEGRA_BOARD_PAZ00_H
+#include <mach/gpio-tegra.h>
+
#define TEGRA_GPIO_SD1_CD TEGRA_GPIO_PV5
#define TEGRA_GPIO_SD1_WP TEGRA_GPIO_PH1
#define TEGRA_GPIO_SD1_POWER TEGRA_GPIO_PT3
#ifndef _MACH_TEGRA_BOARD_SEABOARD_H
#define _MACH_TEGRA_BOARD_SEABOARD_H
+#include <mach/gpio-tegra.h>
+
#define TEGRA_GPIO_SD2_CD TEGRA_GPIO_PI5
#define TEGRA_GPIO_SD2_WP TEGRA_GPIO_PH1
#define TEGRA_GPIO_SD2_POWER TEGRA_GPIO_PI6
* GNU General Public License for more details.
*
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <mach/pinmux.h>
-#include <mach/gpio.h>
#include "gpio-names.h"
#include "board-trimslice.h"
#ifndef _MACH_TEGRA_BOARD_TRIMSLICE_H
#define _MACH_TEGRA_BOARD_TRIMSLICE_H
+#include <mach/gpio-tegra.h>
+
#define TRIMSLICE_GPIO_SD4_CD TEGRA_GPIO_PP1 /* mmc4 cd */
#define TRIMSLICE_GPIO_SD4_WP TEGRA_GPIO_PP2 /* mmc4 wp */
--- /dev/null
+/*
+ * arch/arm/mach-tegra/include/mach/gpio.h
+ *
+ * Copyright (C) 2010 Google, Inc.
+ *
+ * Author:
+ * Erik Gilling <konkers@google.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __MACH_TEGRA_GPIO_TEGRA_H
+#define __MACH_TEGRA_GPIO_TEGRA_H
+
+#include <linux/types.h>
+#include <mach/irqs.h>
+
+#define TEGRA_NR_GPIOS INT_GPIO_NR
+
+#define TEGRA_GPIO_TO_IRQ(gpio) (INT_GPIO_BASE + (gpio))
+
+struct tegra_gpio_table {
+ int gpio; /* GPIO number */
+ bool enable; /* Enable for GPIO at init? */
+};
+
+void tegra_gpio_config(struct tegra_gpio_table *table, int num);
+void tegra_gpio_enable(int gpio);
+void tegra_gpio_disable(int gpio);
+
+#endif
-/*
- * arch/arm/mach-tegra/include/mach/gpio.h
- *
- * Copyright (C) 2010 Google, Inc.
- *
- * Author:
- * Erik Gilling <konkers@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __MACH_TEGRA_GPIO_H
-#define __MACH_TEGRA_GPIO_H
-
-#include <linux/init.h>
-#include <mach/irqs.h>
-
-#define TEGRA_NR_GPIOS INT_GPIO_NR
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-
-#define TEGRA_GPIO_TO_IRQ(gpio) (INT_GPIO_BASE + (gpio))
-#define TEGRA_IRQ_TO_GPIO(irq) ((irq) - INT_GPIO_BASE)
-
-static inline int gpio_to_irq(unsigned int gpio)
-{
- if (gpio < TEGRA_NR_GPIOS)
- return INT_GPIO_BASE + gpio;
- return -EINVAL;
-}
-
-static inline int irq_to_gpio(unsigned int irq)
-{
- if ((irq >= INT_GPIO_BASE) && (irq < INT_GPIO_BASE + INT_GPIO_NR))
- return irq - INT_GPIO_BASE;
- return -EINVAL;
-}
-
-struct tegra_gpio_table {
- int gpio; /* GPIO number */
- bool enable; /* Enable for GPIO at init? */
-};
-
-void tegra_gpio_config(struct tegra_gpio_table *table, int num);
-void tegra_gpio_enable(int gpio);
-void tegra_gpio_disable(int gpio);
-
-#endif
#include <linux/usb/otg.h>
#include <linux/usb/ulpi.h>
#include <asm/mach-types.h>
+#include <mach/gpio-tegra.h>
#include <mach/usb_phy.h>
#include <mach/iomap.h>
config MACH_U300
bool "U300"
+ select GPIO_U300
comment "ST-Ericsson U300/U330/U335/U365 Feature Selections"
#include <mach/hardware.h>
#include <mach/syscon.h>
#include <mach/dma_channels.h>
+#include <mach/gpio-u300.h>
#include "clock.h"
#include "mmc.h"
.end = IRQ_U300_GPIO_PORT2,
.flags = IORESOURCE_IRQ,
},
-#ifdef U300_COH901571_3
+#if defined(CONFIG_MACH_U300_BS365) || defined(CONFIG_MACH_U300_BS335)
{
.name = "gpio3",
.start = IRQ_U300_GPIO_PORT3,
.end = IRQ_U300_GPIO_PORT4,
.flags = IORESOURCE_IRQ,
},
+#endif
#ifdef CONFIG_MACH_U300_BS335
{
.name = "gpio5",
.flags = IORESOURCE_IRQ,
},
#endif /* CONFIG_MACH_U300_BS335 */
-#endif /* U300_COH901571_3 */
};
static struct resource keypad_resources[] = {
.resource = i2c1_resources,
};
+/*
+ * The different variants have a few different versions of the
+ * GPIO block, with different number of ports.
+ */
+static struct u300_gpio_platform u300_gpio_plat = {
+#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330)
+ .variant = U300_GPIO_COH901335,
+ .ports = 3,
+#endif
+#ifdef CONFIG_MACH_U300_BS335
+ .variant = U300_GPIO_COH901571_3_BS335,
+ .ports = 7,
+#endif
+#ifdef CONFIG_MACH_U300_BS365
+ .variant = U300_GPIO_COH901571_3_BS365,
+ .ports = 5,
+#endif
+ .gpio_base = 0,
+ .gpio_irq_base = IRQ_U300_GPIO_BASE,
+};
+
static struct platform_device gpio_device = {
.name = "u300-gpio",
.id = -1,
.num_resources = ARRAY_SIZE(gpio_resources),
.resource = gpio_resources,
+ .dev = {
+ .platform_data = &u300_gpio_plat,
+ },
};
static struct platform_device keypad_device = {
BUG_ON(IS_ERR(clk));
clk_enable(clk);
- for (i = 0; i < NR_IRQS; i++)
+ for (i = 0; i < U300_VIC_IRQS_END; i++)
set_bit(i, (unsigned long *) &mask[0]);
vic_init((void __iomem *) U300_INTCON0_VBASE, 0, mask[0], mask[0]);
vic_init((void __iomem *) U300_INTCON1_VBASE, 32, mask[1], mask[1]);
--- /dev/null
+/*
+ * Copyright (C) 2007-2011 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * GPIO block resgister definitions and inline macros for
+ * U300 GPIO COH 901 335 or COH 901 571/3
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+
+#ifndef __MACH_U300_GPIO_U300_H
+#define __MACH_U300_GPIO_U300_H
+
+/*
+ * Individual pin assignments for the B26/S26. Notice that the
+ * actual usage of these pins depends on the PAD MUX settings, that
+ * is why the same number can potentially appear several times.
+ * In the reference design each pin is only used for one purpose.
+ * These were determined by inspecting the B26/S26 schematic:
+ * 2/1911-ROA 128 1603
+ */
+#ifdef CONFIG_MACH_U300_BS2X
+#define U300_GPIO_PIN_UART_RX 0
+#define U300_GPIO_PIN_UART_TX 1
+#define U300_GPIO_PIN_GPIO02 2 /* Unrouted */
+#define U300_GPIO_PIN_GPIO03 3 /* Unrouted */
+#define U300_GPIO_PIN_CAM_SLEEP 4
+#define U300_GPIO_PIN_CAM_REG_EN 5
+#define U300_GPIO_PIN_GPIO06 6 /* Unrouted */
+#define U300_GPIO_PIN_GPIO07 7 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO08 8 /* Service point SP2321 */
+#define U300_GPIO_PIN_GPIO09 9 /* Service point SP2322 */
+#define U300_GPIO_PIN_PHFSENSE 10 /* Headphone jack sensing */
+#define U300_GPIO_PIN_MMC_CLKRET 11 /* Clock return from MMC/SD card */
+#define U300_GPIO_PIN_MMC_CD 12 /* MMC Card insertion detection */
+#define U300_GPIO_PIN_FLIPSENSE 13 /* Mechanical flip sensing */
+#define U300_GPIO_PIN_GPIO14 14 /* DSP JTAG Port RTCK */
+#define U300_GPIO_PIN_GPIO15 15 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO16 16 /* Unrouted */
+#define U300_GPIO_PIN_GPIO17 17 /* Unrouted */
+#define U300_GPIO_PIN_GPIO18 18 /* Unrouted */
+#define U300_GPIO_PIN_GPIO19 19 /* Unrouted */
+#define U300_GPIO_PIN_GPIO20 20 /* Unrouted */
+#define U300_GPIO_PIN_GPIO21 21 /* Unrouted */
+#define U300_GPIO_PIN_GPIO22 22 /* Unrouted */
+#define U300_GPIO_PIN_GPIO23 23 /* Unrouted */
+#endif
+
+/*
+ * Individual pin assignments for the B330/S330 and B365/S365.
+ * Notice that the actual usage of these pins depends on the
+ * PAD MUX settings, that is why the same number can potentially
+ * appear several times. In the reference design each pin is only
+ * used for one purpose. These were determined by inspecting the
+ * S365 schematic.
+ */
+#if defined(CONFIG_MACH_U300_BS330) || defined(CONFIG_MACH_U300_BS365) || \
+ defined(CONFIG_MACH_U300_BS335)
+#define U300_GPIO_PIN_UART_RX 0
+#define U300_GPIO_PIN_UART_TX 1
+#define U300_GPIO_PIN_UART_CTS 2
+#define U300_GPIO_PIN_UART_RTS 3
+#define U300_GPIO_PIN_CAM_MAIN_STANDBY 4 /* Camera MAIN standby */
+#define U300_GPIO_PIN_GPIO05 5 /* Unrouted */
+#define U300_GPIO_PIN_MS_CD 6 /* Memory Stick Card insertion */
+#define U300_GPIO_PIN_GPIO07 7 /* Test point TP2430 */
+
+#define U300_GPIO_PIN_GPIO08 8 /* Test point TP2437 */
+#define U300_GPIO_PIN_GPIO09 9 /* Test point TP2431 */
+#define U300_GPIO_PIN_GPIO10 10 /* Test point TP2432 */
+#define U300_GPIO_PIN_MMC_CLKRET 11 /* Clock return from MMC/SD card */
+#define U300_GPIO_PIN_MMC_CD 12 /* MMC Card insertion detection */
+#define U300_GPIO_PIN_CAM_SUB_STANDBY 13 /* Camera SUB standby */
+#define U300_GPIO_PIN_GPIO14 14 /* Test point TP2436 */
+#define U300_GPIO_PIN_GPIO15 15 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO16 16 /* Test point TP2438 */
+#define U300_GPIO_PIN_PHFSENSE 17 /* Headphone jack sensing */
+#define U300_GPIO_PIN_GPIO18 18 /* Test point TP2439 */
+#define U300_GPIO_PIN_GPIO19 19 /* Routed somewhere */
+#define U300_GPIO_PIN_GPIO20 20 /* Unrouted */
+#define U300_GPIO_PIN_GPIO21 21 /* Unrouted */
+#define U300_GPIO_PIN_GPIO22 22 /* Unrouted */
+#define U300_GPIO_PIN_GPIO23 23 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO24 24 /* Unrouted */
+#define U300_GPIO_PIN_GPIO25 25 /* Unrouted */
+#define U300_GPIO_PIN_GPIO26 26 /* Unrouted */
+#define U300_GPIO_PIN_GPIO27 27 /* Unrouted */
+#define U300_GPIO_PIN_GPIO28 28 /* Unrouted */
+#define U300_GPIO_PIN_GPIO29 29 /* Unrouted */
+#define U300_GPIO_PIN_GPIO30 30 /* Unrouted */
+#define U300_GPIO_PIN_GPIO31 31 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO32 32 /* Unrouted */
+#define U300_GPIO_PIN_GPIO33 33 /* Unrouted */
+#define U300_GPIO_PIN_GPIO34 34 /* Unrouted */
+#define U300_GPIO_PIN_GPIO35 35 /* Unrouted */
+#define U300_GPIO_PIN_GPIO36 36 /* Unrouted */
+#define U300_GPIO_PIN_GPIO37 37 /* Unrouted */
+#define U300_GPIO_PIN_GPIO38 38 /* Unrouted */
+#define U300_GPIO_PIN_GPIO39 39 /* Unrouted */
+
+#ifdef CONFIG_MACH_U300_BS335
+
+#define U300_GPIO_PIN_GPIO40 40 /* Unrouted */
+#define U300_GPIO_PIN_GPIO41 41 /* Unrouted */
+#define U300_GPIO_PIN_GPIO42 42 /* Unrouted */
+#define U300_GPIO_PIN_GPIO43 43 /* Unrouted */
+#define U300_GPIO_PIN_GPIO44 44 /* Unrouted */
+#define U300_GPIO_PIN_GPIO45 45 /* Unrouted */
+#define U300_GPIO_PIN_GPIO46 46 /* Unrouted */
+#define U300_GPIO_PIN_GPIO47 47 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO48 48 /* Unrouted */
+#define U300_GPIO_PIN_GPIO49 49 /* Unrouted */
+#define U300_GPIO_PIN_GPIO50 50 /* Unrouted */
+#define U300_GPIO_PIN_GPIO51 51 /* Unrouted */
+#define U300_GPIO_PIN_GPIO52 52 /* Unrouted */
+#define U300_GPIO_PIN_GPIO53 53 /* Unrouted */
+#define U300_GPIO_PIN_GPIO54 54 /* Unrouted */
+#define U300_GPIO_PIN_GPIO55 55 /* Unrouted */
+#endif
+
+#endif
+
+/**
+ * enum u300_gpio_variant - the type of U300 GPIO employed
+ */
+enum u300_gpio_variant {
+ U300_GPIO_COH901335,
+ U300_GPIO_COH901571_3_BS335,
+ U300_GPIO_COH901571_3_BS365,
+};
+
+/**
+ * struct u300_gpio_platform - U300 GPIO platform data
+ * @variant: IP block variant
+ * @ports: number of GPIO block ports
+ * @gpio_base: first GPIO number for this block (use a free range)
+ * @gpio_irq_base: first GPIO IRQ number for this block (use a free range)
+ */
+struct u300_gpio_platform {
+ enum u300_gpio_variant variant;
+ u8 ports;
+ int gpio_base;
+ int gpio_irq_base;
+};
+
+#endif /* __MACH_U300_GPIO_U300_H */
-/*
- *
- * arch/arm/mach-u300/include/mach/gpio.h
- *
- *
- * Copyright (C) 2007-2009 ST-Ericsson AB
- * License terms: GNU General Public License (GPL) version 2
- * GPIO block resgister definitions and inline macros for
- * U300 GPIO COH 901 335 or COH 901 571/3
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- */
-
-#ifndef __MACH_U300_GPIO_H
-#define __MACH_U300_GPIO_H
-
-#include <linux/kernel.h>
-#include <linux/io.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-
-/* Switch type depending on platform/chip variant */
-#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330)
-#define U300_COH901335
-#endif
-#if defined(CONFIG_MACH_U300_BS365) || defined(CONFIG_MACH_U300_BS335)
-#define U300_COH901571_3
-#endif
-
-/* Get base address for regs here */
-#include "u300-regs.h"
-/* IRQ numbers */
-#include "irqs.h"
-
-/*
- * This is the GPIO block definitions. GPIO (General Purpose I/O) can be
- * used for anything, and often is. The event/enable etc figures are for
- * the lowermost pin (pin 0 on each port), shift this left to match your
- * pin if you're gonna use these values.
- */
-#ifdef U300_COH901335
-#define U300_GPIO_PORTX_SPACING (0x1C)
-/* Port X Pin Data Register 32bit, this is both input and output (R/W) */
-#define U300_GPIO_PXPDIR (0x00)
-#define U300_GPIO_PXPDOR (0x00)
-/* Port X Pin Config Register 32bit (R/W) */
-#define U300_GPIO_PXPCR (0x04)
-#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL)
-#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL)
-#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL)
-/* Port X Interrupt Event Register 32bit (R/W) */
-#define U300_GPIO_PXIEV (0x08)
-#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL)
-/* Port X Interrupt Enable Register 32bit (R/W) */
-#define U300_GPIO_PXIEN (0x0C)
-#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL)
-/* Port X Interrupt Force Register 32bit (R/W) */
-#define U300_GPIO_PXIFR (0x10)
-#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL)
-/* Port X Interrupt Config Register 32bit (R/W) */
-#define U300_GPIO_PXICR (0x14)
-#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL)
-/* Port X Pull-up Enable Register 32bit (R/W) */
-#define U300_GPIO_PXPER (0x18)
-#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
-/* Control Register 32bit (R/W) */
-#define U300_GPIO_CR (0x54)
-#define U300_GPIO_CR_BLOCK_CLOCK_ENABLE (0x00000001UL)
-/* three ports of 8 bits each = GPIO pins 0..23 */
-#define U300_GPIO_NUM_PORTS 3
-#define U300_GPIO_PINS_PER_PORT 8
-#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1)
-#endif
-
-#ifdef U300_COH901571_3
-/*
- * Control Register 32bit (R/W)
- * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
- * gives the number of GPIO pins.
- * bit 8-2 (mask 0x000001FC) contains the core version ID.
- */
-#define U300_GPIO_CR (0x00)
-#define U300_GPIO_CR_SYNC_SEL_ENABLE (0x00000002UL)
-#define U300_GPIO_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL)
-#define U300_GPIO_PORTX_SPACING (0x30)
-/* Port X Pin Data INPUT Register 32bit (R/W) */
-#define U300_GPIO_PXPDIR (0x04)
-/* Port X Pin Data OUTPUT Register 32bit (R/W) */
-#define U300_GPIO_PXPDOR (0x08)
-/* Port X Pin Config Register 32bit (R/W) */
-#define U300_GPIO_PXPCR (0x0C)
-#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL)
-#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL)
-#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL)
-/* Port X Pull-up Enable Register 32bit (R/W) */
-#define U300_GPIO_PXPER (0x10)
-#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
-/* Port X Interrupt Event Register 32bit (R/W) */
-#define U300_GPIO_PXIEV (0x14)
-#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL)
-/* Port X Interrupt Enable Register 32bit (R/W) */
-#define U300_GPIO_PXIEN (0x18)
-#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL)
-/* Port X Interrupt Force Register 32bit (R/W) */
-#define U300_GPIO_PXIFR (0x1C)
-#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL)
-/* Port X Interrupt Config Register 32bit (R/W) */
-#define U300_GPIO_PXICR (0x20)
-#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL)
-#ifdef CONFIG_MACH_U300_BS335
-/* seven ports of 8 bits each = GPIO pins 0..55 */
-#define U300_GPIO_NUM_PORTS 7
-#else
-/* five ports of 8 bits each = GPIO pins 0..39 */
-#define U300_GPIO_NUM_PORTS 5
-#endif
-#define U300_GPIO_PINS_PER_PORT 8
-#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1)
-#endif
-
-/*
- * Individual pin assignments for the B26/S26. Notice that the
- * actual usage of these pins depends on the PAD MUX settings, that
- * is why the same number can potentially appear several times.
- * In the reference design each pin is only used for one purpose.
- * These were determined by inspecting the B26/S26 schematic:
- * 2/1911-ROA 128 1603
- */
-#ifdef CONFIG_MACH_U300_BS2X
-#define U300_GPIO_PIN_UART_RX 0
-#define U300_GPIO_PIN_UART_TX 1
-#define U300_GPIO_PIN_GPIO02 2 /* Unrouted */
-#define U300_GPIO_PIN_GPIO03 3 /* Unrouted */
-#define U300_GPIO_PIN_CAM_SLEEP 4
-#define U300_GPIO_PIN_CAM_REG_EN 5
-#define U300_GPIO_PIN_GPIO06 6 /* Unrouted */
-#define U300_GPIO_PIN_GPIO07 7 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO08 8 /* Service point SP2321 */
-#define U300_GPIO_PIN_GPIO09 9 /* Service point SP2322 */
-#define U300_GPIO_PIN_PHFSENSE 10 /* Headphone jack sensing */
-#define U300_GPIO_PIN_MMC_CLKRET 1