* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
- * $Id: 8250.c,v 1.90 2002/07/28 10:03:27 rmk Exp $
- *
* A note about mapbase / membase
*
* mapbase is the physical address of the IO port.
#include "8250.h"
+#ifdef CONFIG_SPARC
+#include "suncore.h"
+#endif
+
/*
* Configuration:
* share_irqs - whether we pass IRQF_SHARED to request_irq(). This option
static unsigned int nr_uarts = CONFIG_SERIAL_8250_RUNTIME_UARTS;
+static struct uart_driver serial8250_reg;
+
+static int serial_index(struct uart_port *port)
+{
+ return (serial8250_reg.minor - 64) + port->line;
+}
+
/*
* Debugging.
*/
#define CONFIG_HUB6 1
#include <asm/serial.h>
-
/*
* SERIAL_PORT_DFNS tells us about built-in ports that have no
* standard enumeration mechanism. Platforms that can find all
};
struct irq_info {
- spinlock_t lock;
+ struct hlist_node node;
+ int irq;
+ spinlock_t lock; /* Protects list not the hash */
struct list_head *head;
};
-static struct irq_info irq_lists[NR_IRQS];
+#define NR_IRQ_HASH 32 /* Can be adjusted later */
+static struct hlist_head irq_lists[NR_IRQ_HASH];
+static DEFINE_MUTEX(hash_mutex); /* Used to walk the hash */
/*
* Here we define the default xmit fifo size used for each type of UART.
/*
* FIFO support.
*/
-static inline void serial8250_clear_fifos(struct uart_8250_port *p)
+static void serial8250_clear_fifos(struct uart_8250_port *p)
{
if (p->capabilities & UART_CAP_FIFO) {
serial_outp(p, UART_FCR, UART_FCR_ENABLE_FIFO);
* capability" bit enabled. Note that on XR16C850s, we need to
* reset LCR to write to IER.
*/
-static inline void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
+static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
{
if (p->capabilities & UART_CAP_SLEEP) {
if (p->capabilities & UART_CAP_EFR) {
return;
DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04x, 0x%p): ",
- up->port.line, up->port.iobase, up->port.membase);
+ serial_index(&up->port), up->port.iobase, up->port.membase);
/*
* We really do need global IRQs disabled here - we're going to
if (up->capabilities != uart_config[up->port.type].flags) {
printk(KERN_WARNING
"ttyS%d: detected caps %08x should be %08x\n",
- up->port.line, up->capabilities,
- uart_config[up->port.type].flags);
+ serial_index(&up->port), up->capabilities,
+ uart_config[up->port.type].flags);
}
up->port.fifosize = uart_config[up->port.type].fifo_size;
static void
receive_chars(struct uart_8250_port *up, unsigned int *status)
{
- struct tty_struct *tty = up->port.info->tty;
+ struct tty_struct *tty = up->port.info->port.tty;
unsigned char ch, lsr = *status;
int max_count = 256;
char flag;
do {
- ch = serial_inp(up, UART_RX);
+ if (likely(lsr & UART_LSR_DR))
+ ch = serial_inp(up, UART_RX);
+ else
+ /*
+ * Intel 82571 has a Serial Over Lan device that will
+ * set UART_LSR_BI without setting UART_LSR_DR when
+ * it receives a break. To avoid reading from the
+ * receive buffer without UART_LSR_DR bit set, we
+ * just force the read character to be 0
+ */
+ ch = 0;
+
flag = TTY_NORMAL;
up->port.icount.rx++;
ignore_char:
lsr = serial_inp(up, UART_LSR);
- } while ((lsr & UART_LSR_DR) && (max_count-- > 0));
+ } while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (max_count-- > 0));
spin_unlock(&up->port.lock);
tty_flip_buffer_push(tty);
spin_lock(&up->port.lock);
/*
* This handles the interrupt from one port.
*/
-static inline void
-serial8250_handle_port(struct uart_8250_port *up)
+static void serial8250_handle_port(struct uart_8250_port *up)
{
unsigned int status;
unsigned long flags;
DEBUG_INTR("status = %x...", status);
- if (status & UART_LSR_DR)
+ if (status & (UART_LSR_DR | UART_LSR_BI))
receive_chars(up, &status);
check_modem_status(up);
if (status & UART_LSR_THRE)
BUG_ON(i->head != &up->list);
i->head = NULL;
}
-
spin_unlock_irq(&i->lock);
+ /* List empty so throw away the hash node */
+ if (i->head == NULL) {
+ hlist_del(&i->node);
+ kfree(i);
+ }
}
static int serial_link_irq_chain(struct uart_8250_port *up)
{
- struct irq_info *i = irq_lists + up->port.irq;
+ struct hlist_head *h;
+ struct hlist_node *n;
+ struct irq_info *i;
int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? IRQF_SHARED : 0;
+ mutex_lock(&hash_mutex);
+
+ h = &irq_lists[up->port.irq % NR_IRQ_HASH];
+
+ hlist_for_each(n, h) {
+ i = hlist_entry(n, struct irq_info, node);
+ if (i->irq == up->port.irq)
+ break;
+ }
+
+ if (n == NULL) {
+ i = kzalloc(sizeof(struct irq_info), GFP_KERNEL);
+ if (i == NULL) {
+ mutex_unlock(&hash_mutex);
+ return -ENOMEM;
+ }
+ spin_lock_init(&i->lock);
+ i->irq = up->port.irq;
+ hlist_add_head(&i->node, h);
+ }
+ mutex_unlock(&hash_mutex);
+
spin_lock_irq(&i->lock);
if (i->head) {
static void serial_unlink_irq_chain(struct uart_8250_port *up)
{
- struct irq_info *i = irq_lists + up->port.irq;
+ struct irq_info *i;
+ struct hlist_node *n;
+ struct hlist_head *h;
+
+ mutex_lock(&hash_mutex);
+
+ h = &irq_lists[up->port.irq % NR_IRQ_HASH];
+
+ hlist_for_each(n, h) {
+ i = hlist_entry(n, struct irq_info, node);
+ if (i->irq == up->port.irq)
+ break;
+ }
+ BUG_ON(n == NULL);
BUG_ON(i->head == NULL);
if (list_empty(i->head))
free_irq(up->port.irq, i);
serial_do_unlink(i, up);
+ mutex_unlock(&hash_mutex);
}
/* Base timer interval for polling */
/*
* Wait for transmitter & holding register to empty
*/
-static inline void wait_for_xmitr(struct uart_8250_port *up, int bits)
+static void wait_for_xmitr(struct uart_8250_port *up, int bits)
{
unsigned int status, tmout = 10000;
*/
if (!(up->port.flags & UPF_BUGGY_UART) &&
(serial_inp(up, UART_LSR) == 0xff)) {
- printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
+ printk(KERN_INFO "ttyS%d: LSR safety check engaged!\n",
+ serial_index(&up->port));
return -ENODEV;
}
}
if (is_real_interrupt(up->port.irq)) {
+ unsigned char iir1;
/*
* Test for UARTs that do not reassert THRE when the
* transmitter is idle and the interrupt has already
* allow register changes to become visible.
*/
spin_lock_irqsave(&up->port.lock, flags);
+ if (up->port.flags & UPF_SHARE_IRQ)
+ disable_irq_nosync(up->port.irq);
wait_for_xmitr(up, UART_LSR_THRE);
serial_out_sync(up, UART_IER, UART_IER_THRI);
udelay(1); /* allow THRE to set */
- serial_in(up, UART_IIR);
+ iir1 = serial_in(up, UART_IIR);
serial_out(up, UART_IER, 0);
serial_out_sync(up, UART_IER, UART_IER_THRI);
udelay(1); /* allow a working UART time to re-assert THRE */
iir = serial_in(up, UART_IIR);
serial_out(up, UART_IER, 0);
+ if (up->port.flags & UPF_SHARE_IRQ)
+ enable_irq(up->port.irq);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* If the interrupt is not reasserted, setup a timer to
* kick the UART on a regular basis.
*/
- if (iir & UART_IIR_NO_INT) {
- pr_debug("ttyS%d - using backup timer\n", port->line);
- up->timer.function = serial8250_backup_timeout;
- up->timer.data = (unsigned long)up;
- mod_timer(&up->timer, jiffies +
- poll_timeout(up->port.timeout) + HZ / 5);
+ if (!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) {
+ up->bugs |= UART_BUG_THRE;
+ pr_debug("ttyS%d - using backup timer\n",
+ serial_index(port));
}
}
+ /*
+ * The above check will only give an accurate result the first time
+ * the port is opened so this value needs to be preserved.
+ */
+ if (up->bugs & UART_BUG_THRE) {
+ up->timer.function = serial8250_backup_timeout;
+ up->timer.data = (unsigned long)up;
+ mod_timer(&up->timer, jiffies +
+ poll_timeout(up->port.timeout) + HZ / 5);
+ }
+
/*
* If the "interrupt" for this port doesn't correspond with any
* hardware interrupt, we use a timer-based system. The original
if (!(up->bugs & UART_BUG_TXEN)) {
up->bugs |= UART_BUG_TXEN;
pr_debug("ttyS%d - enabling bad tx status workarounds\n",
- port->line);
+ serial_index(port));
}
} else {
up->bugs &= ~UART_BUG_TXEN;
serial_outp(up, UART_EFR, efr);
}
-#ifdef CONFIG_ARCH_OMAP15XX
+#ifdef CONFIG_ARCH_OMAP
/* Workaround to enable 115200 baud on OMAP1510 internal ports */
- if (cpu_is_omap1510() && is_omap_port((unsigned int)up->port.membase)) {
+ if (cpu_is_omap1510() && is_omap_port(up)) {
if (baud == 115200) {
quot = 1;
serial_out(up, UART_OMAP_OSC_12M_SEL, 1);
}
serial8250_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
- tty_termios_encode_baud_rate(termios, baud, baud);
+ /* Don't rewrite B0 */
+ if (tty_termios_baud_rate(termios))
+ tty_termios_encode_baud_rate(termios, baud, baud);
}
static void
p->pm(port, state, oldstate);
}
+static unsigned int serial8250_port_size(struct uart_8250_port *pt)
+{
+ if (pt->port.iotype == UPIO_AU)
+ return 0x100000;
+#ifdef CONFIG_ARCH_OMAP
+ if (is_omap_port(pt))
+ return 0x16 << pt->port.regshift;
+#endif
+ return 8 << pt->port.regshift;
+}
+
/*
* Resource handling.
*/
static int serial8250_request_std_resource(struct uart_8250_port *up)
{
- unsigned int size = 8 << up->port.regshift;
+ unsigned int size = serial8250_port_size(up);
int ret = 0;
switch (up->port.iotype) {
case UPIO_AU:
- size = 0x100000;
- /* fall thru */
case UPIO_TSI:
case UPIO_MEM32:
case UPIO_MEM:
}
if (up->port.flags & UPF_IOREMAP) {
- up->port.membase = ioremap(up->port.mapbase, size);
+ up->port.membase = ioremap_nocache(up->port.mapbase,
+ size);
if (!up->port.membase) {
release_mem_region(up->port.mapbase, size);
ret = -ENOMEM;
static void serial8250_release_std_resource(struct uart_8250_port *up)
{
- unsigned int size = 8 << up->port.regshift;
+ unsigned int size = serial8250_port_size(up);
switch (up->port.iotype) {
case UPIO_AU:
- size = 0x100000;
- /* fall thru */
case UPIO_TSI:
case UPIO_MEM32:
case UPIO_MEM:
static int
serial8250_verify_port(struct uart_port *port, struct serial_struct *ser)
{
- if (ser->irq >= NR_IRQS || ser->irq < 0 ||
+ if (ser->irq >= nr_irqs || ser->irq < 0 ||
ser->baud_base < 9600 || ser->type < PORT_UNKNOWN ||
ser->type >= ARRAY_SIZE(uart_config) || ser->type == PORT_CIRRUS ||
ser->type == PORT_STARTECH)
return serial8250_find_port_for_earlycon();
}
-static struct uart_driver serial8250_reg;
static struct console serial8250_console = {
.name = "ttyS",
.write = serial8250_console_write,
static int __init serial8250_console_init(void)
{
+ if (nr_uarts > UART_NR)
+ nr_uarts = UART_NR;
+
serial8250_isa_init_ports();
register_console(&serial8250_console);
return 0;
.dev_name = "ttyS",
.major = TTY_MAJOR,
.minor = 64,
- .nr = UART_NR,
.cons = SERIAL8250_CONSOLE,
};
*/
int __init early_serial_setup(struct uart_port *port)
{
+ struct uart_port *p;
+
if (port->line >= ARRAY_SIZE(serial8250_ports))
return -ENODEV;
serial8250_isa_init_ports();
- serial8250_ports[port->line].port = *port;
- serial8250_ports[port->line].port.ops = &serial8250_pops;
+ p = &serial8250_ports[port->line].port;
+ p->iobase = port->iobase;
+ p->membase = port->membase;
+ p->irq = port->irq;
+ p->uartclk = port->uartclk;
+ p->fifosize = port->fifosize;
+ p->regshift = port->regshift;
+ p->iotype = port->iotype;
+ p->flags = port->flags;
+ p->mapbase = port->mapbase;
+ p->private_data = port->private_data;
return 0;
}
static int __init serial8250_init(void)
{
- int ret, i;
+ int ret;
if (nr_uarts > UART_NR)
nr_uarts = UART_NR;
- printk(KERN_INFO "Serial: 8250/16550 driver $Revision: 1.90 $ "
+ printk(KERN_INFO "Serial: 8250/16550 driver"
"%d ports, IRQ sharing %sabled\n", nr_uarts,
share_irqs ? "en" : "dis");
- for (i = 0; i < NR_IRQS; i++)
- spin_lock_init(&irq_lists[i].lock);
-
+#ifdef CONFIG_SPARC
+ ret = sunserial_register_minors(&serial8250_reg, UART_NR);
+#else
+ serial8250_reg.nr = UART_NR;
ret = uart_register_driver(&serial8250_reg);
+#endif
if (ret)
goto out;
goto out;
platform_device_del(serial8250_isa_devs);
- put_dev:
+put_dev:
platform_device_put(serial8250_isa_devs);
- unreg_uart_drv:
+unreg_uart_drv:
+#ifdef CONFIG_SPARC
+ sunserial_unregister_minors(&serial8250_reg, UART_NR);
+#else
uart_unregister_driver(&serial8250_reg);
- out:
+#endif
+out:
return ret;
}
platform_driver_unregister(&serial8250_isa_driver);
platform_device_unregister(isa_dev);
+#ifdef CONFIG_SPARC
+ sunserial_unregister_minors(&serial8250_reg, UART_NR);
+#else
uart_unregister_driver(&serial8250_reg);
+#endif
}
module_init(serial8250_init);
EXPORT_SYMBOL(serial8250_resume_port);
MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Generic 8250/16x50 serial driver $Revision: 1.90 $");
+MODULE_DESCRIPTION("Generic 8250/16x50 serial driver");
module_param(share_irqs, uint, 0644);
MODULE_PARM_DESC(share_irqs, "Share IRQs with other non-8250/16x50 devices"