ARM: gpio: at91: convert drivers to use asm/gpio.h rather than mach/gpio.h
[linux-2.6.git] / drivers / ata / pata_at91.c
index 41c94b1..3f4c261 100644 (file)
@@ -3,6 +3,7 @@
  * with CompactFlash interface in True IDE mode
  *
  * Copyright (C) 2009 Matyukevich Sergey
+ *               2011 Igor Plyatov
  *
  * Based on:
  *      * generic platform driver by Paul Mundt: drivers/ata/pata_platform.c
@@ -19,6 +20,7 @@
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/blkdev.h>
+#include <linux/gfp.h>
 #include <scsi/scsi_host.h>
 #include <linux/ata.h>
 #include <linux/clk.h>
 
 #include <mach/at91sam9_smc.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
 
+#define DRV_NAME               "pata_at91"
+#define DRV_VERSION            "0.3"
 
-#define DRV_NAME "pata_at91"
-#define DRV_VERSION "0.1"
-
-#define CF_IDE_OFFSET      0x00c00000
-#define CF_ALT_IDE_OFFSET   0x00e00000
-#define CF_IDE_RES_SIZE     0x08
+#define CF_IDE_OFFSET          0x00c00000
+#define CF_ALT_IDE_OFFSET      0x00e00000
+#define CF_IDE_RES_SIZE                0x08
+#define CS_PULSE_MAXIMUM       319
+#define ER_SMC_CALC            1
+#define ER_SMC_RECALC          2
 
 struct at91_ide_info {
        unsigned long mode;
        unsigned int cs;
-
        struct clk *mck;
-
        void __iomem *ide_addr;
        void __iomem *alt_addr;
 };
 
-static const struct ata_timing initial_timing =
-       {XFER_PIO_0, 70, 290, 240, 600, 165, 150, 600, 0};
+/**
+ * struct smc_range - range of valid values for SMC register.
+ */
+struct smc_range {
+       int min;
+       int max;
+};
+
+/**
+ * adjust_smc_value - adjust value for one of SMC registers.
+ * @value: adjusted value
+ * @range: array of SMC ranges with valid values
+ * @size: SMC ranges array size
+ *
+ * This returns the difference between input and output value or negative
+ * in case of invalid input value.
+ * If negative returned, then output value = maximal possible from ranges.
+ */
+static int adjust_smc_value(int *value, struct smc_range *range, int size)
+{
+       int maximum = (range + size - 1)->max;
+       int remainder;
+
+       do {
+               if (*value < range->min) {
+                       remainder = range->min - *value;
+                       *value = range->min; /* nearest valid value */
+                       return remainder;
+               } else if ((range->min <= *value) && (*value <= range->max))
+                       return 0;
+
+               range++;
+       } while (--size);
+       *value = maximum;
+
+       return -1; /* invalid value */
+}
+
+/**
+ * calc_smc_vals - calculate SMC register values
+ * @dev: ATA device
+ * @setup: SMC_SETUP register value
+ * @pulse: SMC_PULSE register value
+ * @cycle: SMC_CYCLE register value
+ *
+ * This returns negative in case of invalid values for SMC registers:
+ * -ER_SMC_RECALC - recalculation required for SMC values,
+ * -ER_SMC_CALC - calculation failed (invalid input values).
+ *
+ * SMC use special coding scheme, see "Coding and Range of Timing
+ * Parameters" table from AT91SAM9 datasheets.
+ *
+ *     SMC_SETUP = 128*setup[5] + setup[4:0]
+ *     SMC_PULSE = 256*pulse[6] + pulse[5:0]
+ *     SMC_CYCLE = 256*cycle[8:7] + cycle[6:0]
+ */
+static int calc_smc_vals(struct device *dev,
+               int *setup, int *pulse, int *cycle, int *cs_pulse)
+{
+       int ret_val;
+       int err = 0;
+       struct smc_range range_setup[] = {      /* SMC_SETUP valid values */
+               {.min = 0,      .max = 31},     /* first  range */
+               {.min = 128,    .max = 159}     /* second range */
+       };
+       struct smc_range range_pulse[] = {      /* SMC_PULSE valid values */
+               {.min = 0,      .max = 63},     /* first  range */
+               {.min = 256,    .max = 319}     /* second range */
+       };
+       struct smc_range range_cycle[] = {      /* SMC_CYCLE valid values */
+               {.min = 0,      .max = 127},    /* first  range */
+               {.min = 256,    .max = 383},    /* second range */
+               {.min = 512,    .max = 639},    /* third  range */
+               {.min = 768,    .max = 895}     /* fourth range */
+       };
+
+       ret_val = adjust_smc_value(setup, range_setup, ARRAY_SIZE(range_setup));
+       if (ret_val < 0)
+               dev_warn(dev, "maximal SMC Setup value\n");
+       else
+               *cycle += ret_val;
+
+       ret_val = adjust_smc_value(pulse, range_pulse, ARRAY_SIZE(range_pulse));
+       if (ret_val < 0)
+               dev_warn(dev, "maximal SMC Pulse value\n");
+       else
+               *cycle += ret_val;
+
+       ret_val = adjust_smc_value(cycle, range_cycle, ARRAY_SIZE(range_cycle));
+       if (ret_val < 0)
+               dev_warn(dev, "maximal SMC Cycle value\n");
+
+       *cs_pulse = *cycle;
+       if (*cs_pulse > CS_PULSE_MAXIMUM) {
+               dev_err(dev, "unable to calculate valid SMC settings\n");
+               return -ER_SMC_CALC;
+       }
+
+       ret_val = adjust_smc_value(cs_pulse, range_pulse,
+                                       ARRAY_SIZE(range_pulse));
+       if (ret_val < 0) {
+               dev_warn(dev, "maximal SMC CS Pulse value\n");
+       } else if (ret_val != 0) {
+               *cycle = *cs_pulse;
+               dev_warn(dev, "SMC Cycle extended\n");
+               err = -ER_SMC_RECALC;
+       }
+
+       return err;
+}
+
+/**
+ * to_smc_format - convert values into SMC format
+ * @setup: SETUP value of SMC Setup Register
+ * @pulse: PULSE value of SMC Pulse Register
+ * @cycle: CYCLE value of SMC Cycle Register
+ * @cs_pulse: NCS_PULSE value of SMC Pulse Register
+ */
+static void to_smc_format(int *setup, int *pulse, int *cycle, int *cs_pulse)
+{
+       *setup = (*setup & 0x1f) | ((*setup & 0x80) >> 2);
+       *pulse = (*pulse & 0x3f) | ((*pulse & 0x100) >> 2);
+       *cycle = (*cycle & 0x7f) | ((*cycle & 0x300) >> 1);
+       *cs_pulse = (*cs_pulse & 0x3f) | ((*cs_pulse & 0x100) >> 2);
+}
 
 static unsigned long calc_mck_cycles(unsigned long ns, unsigned long mck_hz)
 {
@@ -68,80 +193,77 @@ static unsigned long calc_mck_cycles(unsigned long ns, unsigned long mck_hz)
        return (ns * mul + 65536) >> 16;    /* rounding */
 }
 
-static void set_smc_mode(struct at91_ide_info *info)
-{
-       at91_sys_write(AT91_SMC_MODE(info->cs), info->mode);
-       return;
-}
-
-static void set_smc_timing(struct device *dev,
+/**
+ * set_smc_timing - SMC timings setup.
+ * @dev: device
+ * @info: AT91 IDE info
+ * @ata: ATA timings
+ *
+ * Its assumed that write timings are same as read timings,
+ * cs_setup = 0 and cs_pulse = cycle.
+ */
+static void set_smc_timing(struct device *dev, struct ata_device *adev,
                struct at91_ide_info *info, const struct ata_timing *ata)
 {
-       unsigned long read_cycle, write_cycle, active, recover;
-       unsigned long nrd_setup, nrd_pulse, nrd_recover;
-       unsigned long nwe_setup, nwe_pulse;
-
-       unsigned long ncs_write_setup, ncs_write_pulse;
-       unsigned long ncs_read_setup, ncs_read_pulse;
-
-       unsigned long mck_hz;
-
-       read_cycle  = ata->cyc8b;
-       nrd_setup   = ata->setup;
-       nrd_pulse   = ata->act8b;
-       nrd_recover = ata->rec8b;
-
+       int ret = 0;
+       int use_iordy;
+       unsigned int t6z;         /* data tristate time in ns */
+       unsigned int cycle;       /* SMC Cycle width in MCK ticks */
+       unsigned int setup;       /* SMC Setup width in MCK ticks */
+       unsigned int pulse;       /* CFIOR and CFIOW pulse width in MCK ticks */
+       unsigned int cs_setup = 0;/* CS4 or CS5 setup width in MCK ticks */
+       unsigned int cs_pulse;    /* CS4 or CS5 pulse width in MCK ticks*/
+       unsigned int tdf_cycles;  /* SMC TDF MCK ticks */
+       unsigned long mck_hz;     /* MCK frequency in Hz */
+
+       t6z = (ata->mode < XFER_PIO_5) ? 30 : 20;
        mck_hz = clk_get_rate(info->mck);
+       cycle = calc_mck_cycles(ata->cyc8b, mck_hz);
+       setup = calc_mck_cycles(ata->setup, mck_hz);
+       pulse = calc_mck_cycles(ata->act8b, mck_hz);
+       tdf_cycles = calc_mck_cycles(t6z, mck_hz);
+
+       do {
+               ret = calc_smc_vals(dev, &setup, &pulse, &cycle, &cs_pulse);
+       } while (ret == -ER_SMC_RECALC);
+
+       if (ret == -ER_SMC_CALC)
+               dev_err(dev, "Interface may not operate correctly\n");
+
+       dev_dbg(dev, "SMC Setup=%u, Pulse=%u, Cycle=%u, CS Pulse=%u\n",
+               setup, pulse, cycle, cs_pulse);
+       to_smc_format(&setup, &pulse, &cycle, &cs_pulse);
+       /* disable or enable waiting for IORDY signal */
+       use_iordy = ata_pio_need_iordy(adev);
+       if (use_iordy)
+               info->mode |= AT91_SMC_EXNWMODE_READY;
+
+       if (tdf_cycles > 15) {
+               tdf_cycles = 15;
+               dev_warn(dev, "maximal SMC TDF Cycles value\n");
+       }
 
-       read_cycle  = calc_mck_cycles(read_cycle, mck_hz);
-       nrd_setup   = calc_mck_cycles(nrd_setup, mck_hz);
-       nrd_pulse   = calc_mck_cycles(nrd_pulse, mck_hz);
-       nrd_recover = calc_mck_cycles(nrd_recover, mck_hz);
-
-       active  = nrd_setup + nrd_pulse;
-       recover = read_cycle - active;
-
-       /* Need at least two cycles recovery */
-       if (recover < 2)
-               read_cycle = active + 2;
-
-       /* (CS0, CS1, DIR, OE) <= (CFCE1, CFCE2, CFRNW, NCSX) timings */
-       ncs_read_setup = 1;
-       ncs_read_pulse = read_cycle - 2;
-
-       /* Write timings same as read timings */
-       write_cycle = read_cycle;
-       nwe_setup = nrd_setup;
-       nwe_pulse = nrd_pulse;
-       ncs_write_setup = ncs_read_setup;
-       ncs_write_pulse = ncs_read_pulse;
-
-       dev_dbg(dev, "ATA timings: nrd_setup = %lu nrd_pulse = %lu nrd_cycle = %lu\n",
-                       nrd_setup, nrd_pulse, read_cycle);
-       dev_dbg(dev, "ATA timings: nwe_setup = %lu nwe_pulse = %lu nwe_cycle = %lu\n",
-                       nwe_setup, nwe_pulse, write_cycle);
-       dev_dbg(dev, "ATA timings: ncs_read_setup = %lu ncs_read_pulse = %lu\n",
-                       ncs_read_setup, ncs_read_pulse);
-       dev_dbg(dev, "ATA timings: ncs_write_setup = %lu ncs_write_pulse = %lu\n",
-                       ncs_write_setup, ncs_write_pulse);
+       dev_dbg(dev, "Use IORDY=%u, TDF Cycles=%u\n", use_iordy, tdf_cycles);
+       info->mode |= AT91_SMC_TDF_(tdf_cycles);
 
+       /* write SMC Setup Register */
        at91_sys_write(AT91_SMC_SETUP(info->cs),
-                       AT91_SMC_NWESETUP_(nwe_setup) |
-                       AT91_SMC_NRDSETUP_(nrd_setup) |
-                       AT91_SMC_NCS_WRSETUP_(ncs_write_setup) |
-                       AT91_SMC_NCS_RDSETUP_(ncs_read_setup));
-
+                       AT91_SMC_NWESETUP_(setup) |
+                       AT91_SMC_NRDSETUP_(setup) |
+                       AT91_SMC_NCS_WRSETUP_(cs_setup) |
+                       AT91_SMC_NCS_RDSETUP_(cs_setup));
+       /* write SMC Pulse Register */
        at91_sys_write(AT91_SMC_PULSE(info->cs),
-                       AT91_SMC_NWEPULSE_(nwe_pulse) |
-                       AT91_SMC_NRDPULSE_(nrd_pulse) |
-                       AT91_SMC_NCS_WRPULSE_(ncs_write_pulse) |
-                       AT91_SMC_NCS_RDPULSE_(ncs_read_pulse));
-
+                       AT91_SMC_NWEPULSE_(pulse) |
+                       AT91_SMC_NRDPULSE_(pulse) |
+                       AT91_SMC_NCS_WRPULSE_(cs_pulse) |
+                       AT91_SMC_NCS_RDPULSE_(cs_pulse));
+       /* write SMC Cycle Register */
        at91_sys_write(AT91_SMC_CYCLE(info->cs),
-                       AT91_SMC_NWECYCLE_(write_cycle) |
-                       AT91_SMC_NRDCYCLE_(read_cycle));
-
-       return;
+                       AT91_SMC_NWECYCLE_(cycle) |
+                       AT91_SMC_NRDCYCLE_(cycle));
+       /* write SMC Mode Register*/
+       at91_sys_write(AT91_SMC_MODE(info->cs), info->mode);
 }
 
 static void pata_at91_set_piomode(struct ata_port *ap, struct ata_device *adev)
@@ -153,17 +275,11 @@ static void pata_at91_set_piomode(struct ata_port *ap, struct ata_device *adev)
        /* Compute ATA timing and set it to SMC */
        ret = ata_timing_compute(adev, adev->pio_mode, &timing, 1000, 0);
        if (ret) {
-               dev_warn(ap->dev, "Failed to compute ATA timing %d, \
-                               set PIO_0 timing\n", ret);
-               set_smc_timing(ap->dev, info, &initial_timing);
-       } else {
-               set_smc_timing(ap->dev, info, &timing);
+               dev_warn(ap->dev, "Failed to compute ATA timing %d, "
+                        "set PIO_0 timing\n", ret);
+               timing = *ata_timing_find_mode(XFER_PIO_0);
        }
-
-       /* Setup SMC mode */
-       set_smc_mode(info);
-
-       return;
+       set_smc_timing(ap->dev, adev, info, &timing);
 }
 
 static unsigned int pata_at91_data_xfer_noirq(struct ata_device *dev,
@@ -201,7 +317,6 @@ static struct ata_port_operations pata_at91_port_ops = {
        .sff_data_xfer  = pata_at91_data_xfer_noirq,
        .set_piomode    = pata_at91_set_piomode,
        .cable_detect   = ata_cable_40wire,
-       .port_start     = ATA_OP_NULL,
 };
 
 static int __devinit pata_at91_probe(struct platform_device *pdev)
@@ -330,7 +445,7 @@ static int __devexit pata_at91_remove(struct platform_device *pdev)
 static struct platform_driver pata_at91_driver = {
        .probe          = pata_at91_probe,
        .remove         = __devexit_p(pata_at91_remove),
-       .driver         = {
+       .driver         = {
                .name           = DRV_NAME,
                .owner          = THIS_MODULE,
        },