microblaze: Fix ASM optimized code for LE
[linux-2.6.git] / drivers / usb / host / xhci-ring.c
1 /*
2  * xHCI host controller driver
3  *
4  * Copyright (C) 2008 Intel Corp.
5  *
6  * Author: Sarah Sharp
7  * Some code borrowed from the Linux EHCI driver.
8  *
9  * This program is free software; you can redistribute it and/or modify
10  * it under the terms of the GNU General Public License version 2 as
11  * published by the Free Software Foundation.
12  *
13  * This program is distributed in the hope that it will be useful, but
14  * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
15  * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
16  * for more details.
17  *
18  * You should have received a copy of the GNU General Public License
19  * along with this program; if not, write to the Free Software Foundation,
20  * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
21  */
22
23 /*
24  * Ring initialization rules:
25  * 1. Each segment is initialized to zero, except for link TRBs.
26  * 2. Ring cycle state = 0.  This represents Producer Cycle State (PCS) or
27  *    Consumer Cycle State (CCS), depending on ring function.
28  * 3. Enqueue pointer = dequeue pointer = address of first TRB in the segment.
29  *
30  * Ring behavior rules:
31  * 1. A ring is empty if enqueue == dequeue.  This means there will always be at
32  *    least one free TRB in the ring.  This is useful if you want to turn that
33  *    into a link TRB and expand the ring.
34  * 2. When incrementing an enqueue or dequeue pointer, if the next TRB is a
35  *    link TRB, then load the pointer with the address in the link TRB.  If the
36  *    link TRB had its toggle bit set, you may need to update the ring cycle
37  *    state (see cycle bit rules).  You may have to do this multiple times
38  *    until you reach a non-link TRB.
39  * 3. A ring is full if enqueue++ (for the definition of increment above)
40  *    equals the dequeue pointer.
41  *
42  * Cycle bit rules:
43  * 1. When a consumer increments a dequeue pointer and encounters a toggle bit
44  *    in a link TRB, it must toggle the ring cycle state.
45  * 2. When a producer increments an enqueue pointer and encounters a toggle bit
46  *    in a link TRB, it must toggle the ring cycle state.
47  *
48  * Producer rules:
49  * 1. Check if ring is full before you enqueue.
50  * 2. Write the ring cycle state to the cycle bit in the TRB you're enqueuing.
51  *    Update enqueue pointer between each write (which may update the ring
52  *    cycle state).
53  * 3. Notify consumer.  If SW is producer, it rings the doorbell for command
54  *    and endpoint rings.  If HC is the producer for the event ring,
55  *    and it generates an interrupt according to interrupt modulation rules.
56  *
57  * Consumer rules:
58  * 1. Check if TRB belongs to you.  If the cycle bit == your ring cycle state,
59  *    the TRB is owned by the consumer.
60  * 2. Update dequeue pointer (which may update the ring cycle state) and
61  *    continue processing TRBs until you reach a TRB which is not owned by you.
62  * 3. Notify the producer.  SW is the consumer for the event ring, and it
63  *   updates event ring dequeue pointer.  HC is the consumer for the command and
64  *   endpoint rings; it generates events on the event ring for these.
65  */
66
67 #include <linux/scatterlist.h>
68 #include <linux/slab.h>
69 #include "xhci.h"
70
71 static int handle_cmd_in_cmd_wait_list(struct xhci_hcd *xhci,
72                 struct xhci_virt_device *virt_dev,
73                 struct xhci_event_cmd *event);
74
75 /*
76  * Returns zero if the TRB isn't in this segment, otherwise it returns the DMA
77  * address of the TRB.
78  */
79 dma_addr_t xhci_trb_virt_to_dma(struct xhci_segment *seg,
80                 union xhci_trb *trb)
81 {
82         unsigned long segment_offset;
83
84         if (!seg || !trb || trb < seg->trbs)
85                 return 0;
86         /* offset in TRBs */
87         segment_offset = trb - seg->trbs;
88         if (segment_offset > TRBS_PER_SEGMENT)
89                 return 0;
90         return seg->dma + (segment_offset * sizeof(*trb));
91 }
92
93 /* Does this link TRB point to the first segment in a ring,
94  * or was the previous TRB the last TRB on the last segment in the ERST?
95  */
96 static inline bool last_trb_on_last_seg(struct xhci_hcd *xhci, struct xhci_ring *ring,
97                 struct xhci_segment *seg, union xhci_trb *trb)
98 {
99         if (ring == xhci->event_ring)
100                 return (trb == &seg->trbs[TRBS_PER_SEGMENT]) &&
101                         (seg->next == xhci->event_ring->first_seg);
102         else
103                 return trb->link.control & LINK_TOGGLE;
104 }
105
106 /* Is this TRB a link TRB or was the last TRB the last TRB in this event ring
107  * segment?  I.e. would the updated event TRB pointer step off the end of the
108  * event seg?
109  */
110 static inline int last_trb(struct xhci_hcd *xhci, struct xhci_ring *ring,
111                 struct xhci_segment *seg, union xhci_trb *trb)
112 {
113         if (ring == xhci->event_ring)
114                 return trb == &seg->trbs[TRBS_PER_SEGMENT];
115         else
116                 return (trb->link.control & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK);
117 }
118
119 static inline int enqueue_is_link_trb(struct xhci_ring *ring)
120 {
121         struct xhci_link_trb *link = &ring->enqueue->link;
122         return ((link->control & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK));
123 }
124
125 /* Updates trb to point to the next TRB in the ring, and updates seg if the next
126  * TRB is in a new segment.  This does not skip over link TRBs, and it does not
127  * effect the ring dequeue or enqueue pointers.
128  */
129 static void next_trb(struct xhci_hcd *xhci,
130                 struct xhci_ring *ring,
131                 struct xhci_segment **seg,
132                 union xhci_trb **trb)
133 {
134         if (last_trb(xhci, ring, *seg, *trb)) {
135                 *seg = (*seg)->next;
136                 *trb = ((*seg)->trbs);
137         } else {
138                 (*trb)++;
139         }
140 }
141
142 /*
143  * See Cycle bit rules. SW is the consumer for the event ring only.
144  * Don't make a ring full of link TRBs.  That would be dumb and this would loop.
145  */
146 static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer)
147 {
148         union xhci_trb *next = ++(ring->dequeue);
149         unsigned long long addr;
150
151         ring->deq_updates++;
152         /* Update the dequeue pointer further if that was a link TRB or we're at
153          * the end of an event ring segment (which doesn't have link TRBS)
154          */
155         while (last_trb(xhci, ring, ring->deq_seg, next)) {
156                 if (consumer && last_trb_on_last_seg(xhci, ring, ring->deq_seg, next)) {
157                         ring->cycle_state = (ring->cycle_state ? 0 : 1);
158                         if (!in_interrupt())
159                                 xhci_dbg(xhci, "Toggle cycle state for ring %p = %i\n",
160                                                 ring,
161                                                 (unsigned int) ring->cycle_state);
162                 }
163                 ring->deq_seg = ring->deq_seg->next;
164                 ring->dequeue = ring->deq_seg->trbs;
165                 next = ring->dequeue;
166         }
167         addr = (unsigned long long) xhci_trb_virt_to_dma(ring->deq_seg, ring->dequeue);
168         if (ring == xhci->event_ring)
169                 xhci_dbg(xhci, "Event ring deq = 0x%llx (DMA)\n", addr);
170         else if (ring == xhci->cmd_ring)
171                 xhci_dbg(xhci, "Command ring deq = 0x%llx (DMA)\n", addr);
172         else
173                 xhci_dbg(xhci, "Ring deq = 0x%llx (DMA)\n", addr);
174 }
175
176 /*
177  * See Cycle bit rules. SW is the consumer for the event ring only.
178  * Don't make a ring full of link TRBs.  That would be dumb and this would loop.
179  *
180  * If we've just enqueued a TRB that is in the middle of a TD (meaning the
181  * chain bit is set), then set the chain bit in all the following link TRBs.
182  * If we've enqueued the last TRB in a TD, make sure the following link TRBs
183  * have their chain bit cleared (so that each Link TRB is a separate TD).
184  *
185  * Section 6.4.4.1 of the 0.95 spec says link TRBs cannot have the chain bit
186  * set, but other sections talk about dealing with the chain bit set.  This was
187  * fixed in the 0.96 specification errata, but we have to assume that all 0.95
188  * xHCI hardware can't handle the chain bit being cleared on a link TRB.
189  *
190  * @more_trbs_coming:   Will you enqueue more TRBs before calling
191  *                      prepare_transfer()?
192  */
193 static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring,
194                 bool consumer, bool more_trbs_coming)
195 {
196         u32 chain;
197         union xhci_trb *next;
198         unsigned long long addr;
199
200         chain = ring->enqueue->generic.field[3] & TRB_CHAIN;
201         next = ++(ring->enqueue);
202
203         ring->enq_updates++;
204         /* Update the dequeue pointer further if that was a link TRB or we're at
205          * the end of an event ring segment (which doesn't have link TRBS)
206          */
207         while (last_trb(xhci, ring, ring->enq_seg, next)) {
208                 if (!consumer) {
209                         if (ring != xhci->event_ring) {
210                                 /*
211                                  * If the caller doesn't plan on enqueueing more
212                                  * TDs before ringing the doorbell, then we
213                                  * don't want to give the link TRB to the
214                                  * hardware just yet.  We'll give the link TRB
215                                  * back in prepare_ring() just before we enqueue
216                                  * the TD at the top of the ring.
217                                  */
218                                 if (!chain && !more_trbs_coming)
219                                         break;
220
221                                 /* If we're not dealing with 0.95 hardware,
222                                  * carry over the chain bit of the previous TRB
223                                  * (which may mean the chain bit is cleared).
224                                  */
225                                 if (!xhci_link_trb_quirk(xhci)) {
226                                         next->link.control &= ~TRB_CHAIN;
227                                         next->link.control |= chain;
228                                 }
229                                 /* Give this link TRB to the hardware */
230                                 wmb();
231                                 next->link.control ^= TRB_CYCLE;
232                         }
233                         /* Toggle the cycle bit after the last ring segment. */
234                         if (last_trb_on_last_seg(xhci, ring, ring->enq_seg, next)) {
235                                 ring->cycle_state = (ring->cycle_state ? 0 : 1);
236                                 if (!in_interrupt())
237                                         xhci_dbg(xhci, "Toggle cycle state for ring %p = %i\n",
238                                                         ring,
239                                                         (unsigned int) ring->cycle_state);
240                         }
241                 }
242                 ring->enq_seg = ring->enq_seg->next;
243                 ring->enqueue = ring->enq_seg->trbs;
244                 next = ring->enqueue;
245         }
246         addr = (unsigned long long) xhci_trb_virt_to_dma(ring->enq_seg, ring->enqueue);
247         if (ring == xhci->event_ring)
248                 xhci_dbg(xhci, "Event ring enq = 0x%llx (DMA)\n", addr);
249         else if (ring == xhci->cmd_ring)
250                 xhci_dbg(xhci, "Command ring enq = 0x%llx (DMA)\n", addr);
251         else
252                 xhci_dbg(xhci, "Ring enq = 0x%llx (DMA)\n", addr);
253 }
254
255 /*
256  * Check to see if there's room to enqueue num_trbs on the ring.  See rules
257  * above.
258  * FIXME: this would be simpler and faster if we just kept track of the number
259  * of free TRBs in a ring.
260  */
261 static int room_on_ring(struct xhci_hcd *xhci, struct xhci_ring *ring,
262                 unsigned int num_trbs)
263 {
264         int i;
265         union xhci_trb *enq = ring->enqueue;
266         struct xhci_segment *enq_seg = ring->enq_seg;
267         struct xhci_segment *cur_seg;
268         unsigned int left_on_ring;
269
270         /* If we are currently pointing to a link TRB, advance the
271          * enqueue pointer before checking for space */
272         while (last_trb(xhci, ring, enq_seg, enq)) {
273                 enq_seg = enq_seg->next;
274                 enq = enq_seg->trbs;
275         }
276
277         /* Check if ring is empty */
278         if (enq == ring->dequeue) {
279                 /* Can't use link trbs */
280                 left_on_ring = TRBS_PER_SEGMENT - 1;
281                 for (cur_seg = enq_seg->next; cur_seg != enq_seg;
282                                 cur_seg = cur_seg->next)
283                         left_on_ring += TRBS_PER_SEGMENT - 1;
284
285                 /* Always need one TRB free in the ring. */
286                 left_on_ring -= 1;
287                 if (num_trbs > left_on_ring) {
288                         xhci_warn(xhci, "Not enough room on ring; "
289                                         "need %u TRBs, %u TRBs left\n",
290                                         num_trbs, left_on_ring);
291                         return 0;
292                 }
293                 return 1;
294         }
295         /* Make sure there's an extra empty TRB available */
296         for (i = 0; i <= num_trbs; ++i) {
297                 if (enq == ring->dequeue)
298                         return 0;
299                 enq++;
300                 while (last_trb(xhci, ring, enq_seg, enq)) {
301                         enq_seg = enq_seg->next;
302                         enq = enq_seg->trbs;
303                 }
304         }
305         return 1;
306 }
307
308 /* Ring the host controller doorbell after placing a command on the ring */
309 void xhci_ring_cmd_db(struct xhci_hcd *xhci)
310 {
311         u32 temp;
312
313         xhci_dbg(xhci, "// Ding dong!\n");
314         temp = xhci_readl(xhci, &xhci->dba->doorbell[0]) & DB_MASK;
315         xhci_writel(xhci, temp | DB_TARGET_HOST, &xhci->dba->doorbell[0]);
316         /* Flush PCI posted writes */
317         xhci_readl(xhci, &xhci->dba->doorbell[0]);
318 }
319
320 void xhci_ring_ep_doorbell(struct xhci_hcd *xhci,
321                 unsigned int slot_id,
322                 unsigned int ep_index,
323                 unsigned int stream_id)
324 {
325         struct xhci_virt_ep *ep;
326         unsigned int ep_state;
327         u32 field;
328         __u32 __iomem *db_addr = &xhci->dba->doorbell[slot_id];
329
330         ep = &xhci->devs[slot_id]->eps[ep_index];
331         ep_state = ep->ep_state;
332         /* Don't ring the doorbell for this endpoint if there are pending
333          * cancellations because the we don't want to interrupt processing.
334          * We don't want to restart any stream rings if there's a set dequeue
335          * pointer command pending because the device can choose to start any
336          * stream once the endpoint is on the HW schedule.
337          * FIXME - check all the stream rings for pending cancellations.
338          */
339         if (!(ep_state & EP_HALT_PENDING) && !(ep_state & SET_DEQ_PENDING)
340                         && !(ep_state & EP_HALTED)) {
341                 field = xhci_readl(xhci, db_addr) & DB_MASK;
342                 field |= EPI_TO_DB(ep_index) | STREAM_ID_TO_DB(stream_id);
343                 xhci_writel(xhci, field, db_addr);
344         }
345 }
346
347 /* Ring the doorbell for any rings with pending URBs */
348 static void ring_doorbell_for_active_rings(struct xhci_hcd *xhci,
349                 unsigned int slot_id,
350                 unsigned int ep_index)
351 {
352         unsigned int stream_id;
353         struct xhci_virt_ep *ep;
354
355         ep = &xhci->devs[slot_id]->eps[ep_index];
356
357         /* A ring has pending URBs if its TD list is not empty */
358         if (!(ep->ep_state & EP_HAS_STREAMS)) {
359                 if (!(list_empty(&ep->ring->td_list)))
360                         xhci_ring_ep_doorbell(xhci, slot_id, ep_index, 0);
361                 return;
362         }
363
364         for (stream_id = 1; stream_id < ep->stream_info->num_streams;
365                         stream_id++) {
366                 struct xhci_stream_info *stream_info = ep->stream_info;
367                 if (!list_empty(&stream_info->stream_rings[stream_id]->td_list))
368                         xhci_ring_ep_doorbell(xhci, slot_id, ep_index,
369                                                 stream_id);
370         }
371 }
372
373 /*
374  * Find the segment that trb is in.  Start searching in start_seg.
375  * If we must move past a segment that has a link TRB with a toggle cycle state
376  * bit set, then we will toggle the value pointed at by cycle_state.
377  */
378 static struct xhci_segment *find_trb_seg(
379                 struct xhci_segment *start_seg,
380                 union xhci_trb  *trb, int *cycle_state)
381 {
382         struct xhci_segment *cur_seg = start_seg;
383         struct xhci_generic_trb *generic_trb;
384
385         while (cur_seg->trbs > trb ||
386                         &cur_seg->trbs[TRBS_PER_SEGMENT - 1] < trb) {
387                 generic_trb = &cur_seg->trbs[TRBS_PER_SEGMENT - 1].generic;
388                 if ((generic_trb->field[3] & TRB_TYPE_BITMASK) ==
389                                 TRB_TYPE(TRB_LINK) &&
390                                 (generic_trb->field[3] & LINK_TOGGLE))
391                         *cycle_state = ~(*cycle_state) & 0x1;
392                 cur_seg = cur_seg->next;
393                 if (cur_seg == start_seg)
394                         /* Looped over the entire list.  Oops! */
395                         return NULL;
396         }
397         return cur_seg;
398 }
399
400
401 static struct xhci_ring *xhci_triad_to_transfer_ring(struct xhci_hcd *xhci,
402                 unsigned int slot_id, unsigned int ep_index,
403                 unsigned int stream_id)
404 {
405         struct xhci_virt_ep *ep;
406
407         ep = &xhci->devs[slot_id]->eps[ep_index];
408         /* Common case: no streams */
409         if (!(ep->ep_state & EP_HAS_STREAMS))
410                 return ep->ring;
411
412         if (stream_id == 0) {
413                 xhci_warn(xhci,
414                                 "WARN: Slot ID %u, ep index %u has streams, "
415                                 "but URB has no stream ID.\n",
416                                 slot_id, ep_index);
417                 return NULL;
418         }
419
420         if (stream_id < ep->stream_info->num_streams)
421                 return ep->stream_info->stream_rings[stream_id];
422
423         xhci_warn(xhci,
424                         "WARN: Slot ID %u, ep index %u has "
425                         "stream IDs 1 to %u allocated, "
426                         "but stream ID %u is requested.\n",
427                         slot_id, ep_index,
428                         ep->stream_info->num_streams - 1,
429                         stream_id);
430         return NULL;
431 }
432
433 /* Get the right ring for the given URB.
434  * If the endpoint supports streams, boundary check the URB's stream ID.
435  * If the endpoint doesn't support streams, return the singular endpoint ring.
436  */
437 static struct xhci_ring *xhci_urb_to_transfer_ring(struct xhci_hcd *xhci,
438                 struct urb *urb)
439 {
440         return xhci_triad_to_transfer_ring(xhci, urb->dev->slot_id,
441                 xhci_get_endpoint_index(&urb->ep->desc), urb->stream_id);
442 }
443
444 /*
445  * Move the xHC's endpoint ring dequeue pointer past cur_td.
446  * Record the new state of the xHC's endpoint ring dequeue segment,
447  * dequeue pointer, and new consumer cycle state in state.
448  * Update our internal representation of the ring's dequeue pointer.
449  *
450  * We do this in three jumps:
451  *  - First we update our new ring state to be the same as when the xHC stopped.
452  *  - Then we traverse the ring to find the segment that contains
453  *    the last TRB in the TD.  We toggle the xHC's new cycle state when we pass
454  *    any link TRBs with the toggle cycle bit set.
455  *  - Finally we move the dequeue state one TRB further, toggling the cycle bit
456  *    if we've moved it past a link TRB with the toggle cycle bit set.
457  */
458 void xhci_find_new_dequeue_state(struct xhci_hcd *xhci,
459                 unsigned int slot_id, unsigned int ep_index,
460                 unsigned int stream_id, struct xhci_td *cur_td,
461                 struct xhci_dequeue_state *state)
462 {
463         struct xhci_virt_device *dev = xhci->devs[slot_id];
464         struct xhci_ring *ep_ring;
465         struct xhci_generic_trb *trb;
466         struct xhci_ep_ctx *ep_ctx;
467         dma_addr_t addr;
468
469         ep_ring = xhci_triad_to_transfer_ring(xhci, slot_id,
470                         ep_index, stream_id);
471         if (!ep_ring) {
472                 xhci_warn(xhci, "WARN can't find new dequeue state "
473                                 "for invalid stream ID %u.\n",
474                                 stream_id);
475                 return;
476         }
477         state->new_cycle_state = 0;
478         xhci_dbg(xhci, "Finding segment containing stopped TRB.\n");
479         state->new_deq_seg = find_trb_seg(cur_td->start_seg,
480                         dev->eps[ep_index].stopped_trb,
481                         &state->new_cycle_state);
482         if (!state->new_deq_seg)
483                 BUG();
484         /* Dig out the cycle state saved by the xHC during the stop ep cmd */
485         xhci_dbg(xhci, "Finding endpoint context\n");
486         ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index);
487         state->new_cycle_state = 0x1 & ep_ctx->deq;
488
489         state->new_deq_ptr = cur_td->last_trb;
490         xhci_dbg(xhci, "Finding segment containing last TRB in TD.\n");
491         state->new_deq_seg = find_trb_seg(state->new_deq_seg,
492                         state->new_deq_ptr,
493                         &state->new_cycle_state);
494         if (!state->new_deq_seg)
495                 BUG();
496
497         trb = &state->new_deq_ptr->generic;
498         if ((trb->field[3] & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK) &&
499                                 (trb->field[3] & LINK_TOGGLE))
500                 state->new_cycle_state = ~(state->new_cycle_state) & 0x1;
501         next_trb(xhci, ep_ring, &state->new_deq_seg, &state->new_deq_ptr);
502
503         /* Don't update the ring cycle state for the producer (us). */
504         xhci_dbg(xhci, "New dequeue segment = %p (virtual)\n",
505                         state->new_deq_seg);
506         addr = xhci_trb_virt_to_dma(state->new_deq_seg, state->new_deq_ptr);
507         xhci_dbg(xhci, "New dequeue pointer = 0x%llx (DMA)\n",
508                         (unsigned long long) addr);
509         xhci_dbg(xhci, "Setting dequeue pointer in internal ring state.\n");
510         ep_ring->dequeue = state->new_deq_ptr;
511         ep_ring->deq_seg = state->new_deq_seg;
512 }
513
514 static void td_to_noop(struct xhci_hcd *xhci, struct xhci_ring *ep_ring,
515                 struct xhci_td *cur_td)
516 {
517         struct xhci_segment *cur_seg;
518         union xhci_trb *cur_trb;
519
520         for (cur_seg = cur_td->start_seg, cur_trb = cur_td->first_trb;
521                         true;
522                         next_trb(xhci, ep_ring, &cur_seg, &cur_trb)) {
523                 if ((cur_trb->generic.field[3] & TRB_TYPE_BITMASK) ==
524                                 TRB_TYPE(TRB_LINK)) {
525                         /* Unchain any chained Link TRBs, but
526                          * leave the pointers intact.
527                          */
528                         cur_trb->generic.field[3] &= ~TRB_CHAIN;
529                         xhci_dbg(xhci, "Cancel (unchain) link TRB\n");
530                         xhci_dbg(xhci, "Address = %p (0x%llx dma); "
531                                         "in seg %p (0x%llx dma)\n",
532                                         cur_trb,
533                                         (unsigned long long)xhci_trb_virt_to_dma(cur_seg, cur_trb),
534                                         cur_seg,
535                                         (unsigned long long)cur_seg->dma);
536                 } else {
537                         cur_trb->generic.field[0] = 0;
538                         cur_trb->generic.field[1] = 0;
539                         cur_trb->generic.field[2] = 0;
540                         /* Preserve only the cycle bit of this TRB */
541                         cur_trb->generic.field[3] &= TRB_CYCLE;
542                         cur_trb->generic.field[3] |= TRB_TYPE(TRB_TR_NOOP);
543                         xhci_dbg(xhci, "Cancel TRB %p (0x%llx dma) "
544                                         "in seg %p (0x%llx dma)\n",
545                                         cur_trb,
546                                         (unsigned long long)xhci_trb_virt_to_dma(cur_seg, cur_trb),
547                                         cur_seg,
548                                         (unsigned long long)cur_seg->dma);
549                 }
550                 if (cur_trb == cur_td->last_trb)
551                         break;
552         }
553 }
554
555 static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id,
556                 unsigned int ep_index, unsigned int stream_id,
557                 struct xhci_segment *deq_seg,
558                 union xhci_trb *deq_ptr, u32 cycle_state);
559
560 void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci,
561                 unsigned int slot_id, unsigned int ep_index,
562                 unsigned int stream_id,
563                 struct xhci_dequeue_state *deq_state)
564 {
565         struct xhci_virt_ep *ep = &xhci->devs[slot_id]->eps[ep_index];
566
567         xhci_dbg(xhci, "Set TR Deq Ptr cmd, new deq seg = %p (0x%llx dma), "
568                         "new deq ptr = %p (0x%llx dma), new cycle = %u\n",
569                         deq_state->new_deq_seg,
570                         (unsigned long long)deq_state->new_deq_seg->dma,
571                         deq_state->new_deq_ptr,
572                         (unsigned long long)xhci_trb_virt_to_dma(deq_state->new_deq_seg, deq_state->new_deq_ptr),
573                         deq_state->new_cycle_state);
574         queue_set_tr_deq(xhci, slot_id, ep_index, stream_id,
575                         deq_state->new_deq_seg,
576                         deq_state->new_deq_ptr,
577                         (u32) deq_state->new_cycle_state);
578         /* Stop the TD queueing code from ringing the doorbell until
579          * this command completes.  The HC won't set the dequeue pointer
580          * if the ring is running, and ringing the doorbell starts the
581          * ring running.
582          */
583         ep->ep_state |= SET_DEQ_PENDING;
584 }
585
586 static inline void xhci_stop_watchdog_timer_in_irq(struct xhci_hcd *xhci,
587                 struct xhci_virt_ep *ep)
588 {
589         ep->ep_state &= ~EP_HALT_PENDING;
590         /* Can't del_timer_sync in interrupt, so we attempt to cancel.  If the
591          * timer is running on another CPU, we don't decrement stop_cmds_pending
592          * (since we didn't successfully stop the watchdog timer).
593          */
594         if (del_timer(&ep->stop_cmd_timer))
595                 ep->stop_cmds_pending--;
596 }
597
598 /* Must be called with xhci->lock held in interrupt context */
599 static void xhci_giveback_urb_in_irq(struct xhci_hcd *xhci,
600                 struct xhci_td *cur_td, int status, char *adjective)
601 {
602         struct usb_hcd *hcd = xhci_to_hcd(xhci);
603         struct urb      *urb;
604         struct urb_priv *urb_priv;
605
606         urb = cur_td->urb;
607         urb_priv = urb->hcpriv;
608         urb_priv->td_cnt++;
609
610         /* Only giveback urb when this is the last td in urb */
611         if (urb_priv->td_cnt == urb_priv->length) {
612                 usb_hcd_unlink_urb_from_ep(hcd, urb);
613                 xhci_dbg(xhci, "Giveback %s URB %p\n", adjective, urb);
614
615                 spin_unlock(&xhci->lock);
616                 usb_hcd_giveback_urb(hcd, urb, status);
617                 xhci_urb_free_priv(xhci, urb_priv);
618                 spin_lock(&xhci->lock);
619                 xhci_dbg(xhci, "%s URB given back\n", adjective);
620         }
621 }
622
623 /*
624  * When we get a command completion for a Stop Endpoint Command, we need to
625  * unlink any cancelled TDs from the ring.  There are two ways to do that:
626  *
627  *  1. If the HW was in the middle of processing the TD that needs to be
628  *     cancelled, then we must move the ring's dequeue pointer past the last TRB
629  *     in the TD with a Set Dequeue Pointer Command.
630  *  2. Otherwise, we turn all the TRBs in the TD into No-op TRBs (with the chain
631  *     bit cleared) so that the HW will skip over them.
632  */
633 static void handle_stopped_endpoint(struct xhci_hcd *xhci,
634                 union xhci_trb *trb, struct xhci_event_cmd *event)
635 {
636         unsigned int slot_id;
637         unsigned int ep_index;
638         struct xhci_virt_device *virt_dev;
639         struct xhci_ring *ep_ring;
640         struct xhci_virt_ep *ep;
641         struct list_head *entry;
642         struct xhci_td *cur_td = NULL;
643         struct xhci_td *last_unlinked_td;
644
645         struct xhci_dequeue_state deq_state;
646
647         if (unlikely(TRB_TO_SUSPEND_PORT(
648                         xhci->cmd_ring->dequeue->generic.field[3]))) {
649                 slot_id = TRB_TO_SLOT_ID(
650                         xhci->cmd_ring->dequeue->generic.field[3]);
651                 virt_dev = xhci->devs[slot_id];
652                 if (virt_dev)
653                         handle_cmd_in_cmd_wait_list(xhci, virt_dev,
654                                 event);
655                 else
656                         xhci_warn(xhci, "Stop endpoint command "
657                                 "completion for disabled slot %u\n",
658                                 slot_id);
659                 return;
660         }
661
662         memset(&deq_state, 0, sizeof(deq_state));
663         slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]);
664         ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]);
665         ep = &xhci->devs[slot_id]->eps[ep_index];
666
667         if (list_empty(&ep->cancelled_td_list)) {
668                 xhci_stop_watchdog_timer_in_irq(xhci, ep);
669                 ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
670                 return;
671         }
672
673         /* Fix up the ep ring first, so HW stops executing cancelled TDs.
674          * We have the xHCI lock, so nothing can modify this list until we drop
675          * it.  We're also in the event handler, so we can't get re-interrupted
676          * if another Stop Endpoint command completes
677          */
678         list_for_each(entry, &ep->cancelled_td_list) {
679                 cur_td = list_entry(entry, struct xhci_td, cancelled_td_list);
680                 xhci_dbg(xhci, "Cancelling TD starting at %p, 0x%llx (dma).\n",
681                                 cur_td->first_trb,
682                                 (unsigned long long)xhci_trb_virt_to_dma(cur_td->start_seg, cur_td->first_trb));
683                 ep_ring = xhci_urb_to_transfer_ring(xhci, cur_td->urb);
684                 if (!ep_ring) {
685                         /* This shouldn't happen unless a driver is mucking
686                          * with the stream ID after submission.  This will
687                          * leave the TD on the hardware ring, and the hardware
688                          * will try to execute it, and may access a buffer
689                          * that has already been freed.  In the best case, the
690                          * hardware will execute it, and the event handler will
691                          * ignore the completion event for that TD, since it was
692                          * removed from the td_list for that endpoint.  In
693                          * short, don't muck with the stream ID after
694                          * submission.
695                          */
696                         xhci_warn(xhci, "WARN Cancelled URB %p "
697                                         "has invalid stream ID %u.\n",
698                                         cur_td->urb,
699                                         cur_td->urb->stream_id);
700                         goto remove_finished_td;
701                 }
702                 /*
703                  * If we stopped on the TD we need to cancel, then we have to
704                  * move the xHC endpoint ring dequeue pointer past this TD.
705                  */
706                 if (cur_td == ep->stopped_td)
707                         xhci_find_new_dequeue_state(xhci, slot_id, ep_index,
708                                         cur_td->urb->stream_id,
709                                         cur_td, &deq_state);
710                 else
711                         td_to_noop(xhci, ep_ring, cur_td);
712 remove_finished_td:
713                 /*
714                  * The event handler won't see a completion for this TD anymore,
715                  * so remove it from the endpoint ring's TD list.  Keep it in
716                  * the cancelled TD list for URB completion later.
717                  */
718                 list_del(&cur_td->td_list);
719         }
720         last_unlinked_td = cur_td;
721         xhci_stop_watchdog_timer_in_irq(xhci, ep);
722
723         /* If necessary, queue a Set Transfer Ring Dequeue Pointer command */
724         if (deq_state.new_deq_ptr && deq_state.new_deq_seg) {
725                 xhci_queue_new_dequeue_state(xhci,
726                                 slot_id, ep_index,
727                                 ep->stopped_td->urb->stream_id,
728                                 &deq_state);
729                 xhci_ring_cmd_db(xhci);
730         } else {
731                 /* Otherwise ring the doorbell(s) to restart queued transfers */
732                 ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
733         }
734         ep->stopped_td = NULL;
735         ep->stopped_trb = NULL;
736
737         /*
738          * Drop the lock and complete the URBs in the cancelled TD list.
739          * New TDs to be cancelled might be added to the end of the list before
740          * we can complete all the URBs for the TDs we already unlinked.
741          * So stop when we've completed the URB for the last TD we unlinked.
742          */
743         do {
744                 cur_td = list_entry(ep->cancelled_td_list.next,
745                                 struct xhci_td, cancelled_td_list);
746                 list_del(&cur_td->cancelled_td_list);
747
748                 /* Clean up the cancelled URB */
749                 /* Doesn't matter what we pass for status, since the core will
750                  * just overwrite it (because the URB has been unlinked).
751                  */
752                 xhci_giveback_urb_in_irq(xhci, cur_td, 0, "cancelled");
753
754                 /* Stop processing the cancelled list if the watchdog timer is
755                  * running.
756                  */
757                 if (xhci->xhc_state & XHCI_STATE_DYING)
758                         return;
759         } while (cur_td != last_unlinked_td);
760
761         /* Return to the event handler with xhci->lock re-acquired */
762 }
763
764 /* Watchdog timer function for when a stop endpoint command fails to complete.
765  * In this case, we assume the host controller is broken or dying or dead.  The
766  * host may still be completing some other events, so we have to be careful to
767  * let the event ring handler and the URB dequeueing/enqueueing functions know
768  * through xhci->state.
769  *
770  * The timer may also fire if the host takes a very long time to respond to the
771  * command, and the stop endpoint command completion handler cannot delete the
772  * timer before the timer function is called.  Another endpoint cancellation may
773  * sneak in before the timer function can grab the lock, and that may queue
774  * another stop endpoint command and add the timer back.  So we cannot use a
775  * simple flag to say whether there is a pending stop endpoint command for a
776  * particular endpoint.
777  *
778  * Instead we use a combination of that flag and a counter for the number of
779  * pending stop endpoint commands.  If the timer is the tail end of the last
780  * stop endpoint command, and the endpoint's command is still pending, we assume
781  * the host is dying.
782  */
783 void xhci_stop_endpoint_command_watchdog(unsigned long arg)
784 {
785         struct xhci_hcd *xhci;
786         struct xhci_virt_ep *ep;
787         struct xhci_virt_ep *temp_ep;
788         struct xhci_ring *ring;
789         struct xhci_td *cur_td;
790         int ret, i, j;
791
792         ep = (struct xhci_virt_ep *) arg;
793         xhci = ep->xhci;
794
795         spin_lock(&xhci->lock);
796
797         ep->stop_cmds_pending--;
798         if (xhci->xhc_state & XHCI_STATE_DYING) {
799                 xhci_dbg(xhci, "Stop EP timer ran, but another timer marked "
800                                 "xHCI as DYING, exiting.\n");
801                 spin_unlock(&xhci->lock);
802                 return;
803         }
804         if (!(ep->stop_cmds_pending == 0 && (ep->ep_state & EP_HALT_PENDING))) {
805                 xhci_dbg(xhci, "Stop EP timer ran, but no command pending, "
806                                 "exiting.\n");
807                 spin_unlock(&xhci->lock);
808                 return;
809         }
810
811         xhci_warn(xhci, "xHCI host not responding to stop endpoint command.\n");
812         xhci_warn(xhci, "Assuming host is dying, halting host.\n");
813         /* Oops, HC is dead or dying or at least not responding to the stop
814          * endpoint command.
815          */
816         xhci->xhc_state |= XHCI_STATE_DYING;
817         /* Disable interrupts from the host controller and start halting it */
818         xhci_quiesce(xhci);
819         spin_unlock(&xhci->lock);
820
821         ret = xhci_halt(xhci);
822
823         spin_lock(&xhci->lock);
824         if (ret < 0) {
825                 /* This is bad; the host is not responding to commands and it's
826                  * not allowing itself to be halted.  At least interrupts are
827                  * disabled, so we can set HC_STATE_HALT and notify the
828                  * USB core.  But if we call usb_hc_died(), it will attempt to
829                  * disconnect all device drivers under this host.  Those
830                  * disconnect() methods will wait for all URBs to be unlinked,
831                  * so we must complete them.
832                  */
833                 xhci_warn(xhci, "Non-responsive xHCI host is not halting.\n");
834                 xhci_warn(xhci, "Completing active URBs anyway.\n");
835                 /* We could turn all TDs on the rings to no-ops.  This won't
836                  * help if the host has cached part of the ring, and is slow if
837                  * we want to preserve the cycle bit.  Skip it and hope the host
838                  * doesn't touch the memory.
839                  */
840         }
841         for (i = 0; i < MAX_HC_SLOTS; i++) {
842                 if (!xhci->devs[i])
843                         continue;
844                 for (j = 0; j < 31; j++) {
845                         temp_ep = &xhci->devs[i]->eps[j];
846                         ring = temp_ep->ring;
847                         if (!ring)
848                                 continue;
849                         xhci_dbg(xhci, "Killing URBs for slot ID %u, "
850                                         "ep index %u\n", i, j);
851                         while (!list_empty(&ring->td_list)) {
852                                 cur_td = list_first_entry(&ring->td_list,
853                                                 struct xhci_td,
854                                                 td_list);
855                                 list_del(&cur_td->td_list);
856                                 if (!list_empty(&cur_td->cancelled_td_list))
857                                         list_del(&cur_td->cancelled_td_list);
858                                 xhci_giveback_urb_in_irq(xhci, cur_td,
859                                                 -ESHUTDOWN, "killed");
860                         }
861                         while (!list_empty(&temp_ep->cancelled_td_list)) {
862                                 cur_td = list_first_entry(
863                                                 &temp_ep->cancelled_td_list,
864                                                 struct xhci_td,
865                                                 cancelled_td_list);
866                                 list_del(&cur_td->cancelled_td_list);
867                                 xhci_giveback_urb_in_irq(xhci, cur_td,
868                                                 -ESHUTDOWN, "killed");
869                         }
870                 }
871         }
872         spin_unlock(&xhci->lock);
873         xhci_to_hcd(xhci)->state = HC_STATE_HALT;
874         xhci_dbg(xhci, "Calling usb_hc_died()\n");
875         usb_hc_died(xhci_to_hcd(xhci));
876         xhci_dbg(xhci, "xHCI host controller is dead.\n");
877 }
878
879 /*
880  * When we get a completion for a Set Transfer Ring Dequeue Pointer command,
881  * we need to clear the set deq pending flag in the endpoint ring state, so that
882  * the TD queueing code can ring the doorbell again.  We also need to ring the
883  * endpoint doorbell to restart the ring, but only if there aren't more
884  * cancellations pending.
885  */
886 static void handle_set_deq_completion(struct xhci_hcd *xhci,
887                 struct xhci_event_cmd *event,
888                 union xhci_trb *trb)
889 {
890         unsigned int slot_id;
891         unsigned int ep_index;
892         unsigned int stream_id;
893         struct xhci_ring *ep_ring;
894         struct xhci_virt_device *dev;
895         struct xhci_ep_ctx *ep_ctx;
896         struct xhci_slot_ctx *slot_ctx;
897
898         slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]);
899         ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]);
900         stream_id = TRB_TO_STREAM_ID(trb->generic.field[2]);
901         dev = xhci->devs[slot_id];
902
903         ep_ring = xhci_stream_id_to_ring(dev, ep_index, stream_id);
904         if (!ep_ring) {
905                 xhci_warn(xhci, "WARN Set TR deq ptr command for "
906                                 "freed stream ID %u\n",
907                                 stream_id);
908                 /* XXX: Harmless??? */
909                 dev->eps[ep_index].ep_state &= ~SET_DEQ_PENDING;
910                 return;
911         }
912
913         ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index);
914         slot_ctx = xhci_get_slot_ctx(xhci, dev->out_ctx);
915
916         if (GET_COMP_CODE(event->status) != COMP_SUCCESS) {
917                 unsigned int ep_state;
918                 unsigned int slot_state;
919
920                 switch (GET_COMP_CODE(event->status)) {
921                 case COMP_TRB_ERR:
922                         xhci_warn(xhci, "WARN Set TR Deq Ptr cmd invalid because "
923                                         "of stream ID configuration\n");
924                         break;
925                 case COMP_CTX_STATE:
926                         xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed due "
927                                         "to incorrect slot or ep state.\n");
928                         ep_state = ep_ctx->ep_info;
929                         ep_state &= EP_STATE_MASK;
930                         slot_state = slot_ctx->dev_state;
931                         slot_state = GET_SLOT_STATE(slot_state);
932                         xhci_dbg(xhci, "Slot state = %u, EP state = %u\n",
933                                         slot_state, ep_state);
934                         break;
935                 case COMP_EBADSLT:
936                         xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed because "
937                                         "slot %u was not enabled.\n", slot_id);
938                         break;
939                 default:
940                         xhci_warn(xhci, "WARN Set TR Deq Ptr cmd with unknown "
941                                         "completion code of %u.\n",
942                                         GET_COMP_CODE(event->status));
943                         break;
944                 }
945                 /* OK what do we do now?  The endpoint state is hosed, and we
946                  * should never get to this point if the synchronization between
947                  * queueing, and endpoint state are correct.  This might happen
948                  * if the device gets disconnected after we've finished
949                  * cancelling URBs, which might not be an error...
950                  */
951         } else {
952                 xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq = @%08llx\n",
953                                 ep_ctx->deq);
954         }
955
956         dev->eps[ep_index].ep_state &= ~SET_DEQ_PENDING;
957         /* Restart any rings with pending URBs */
958         ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
959 }
960
961 static void handle_reset_ep_completion(struct xhci_hcd *xhci,
962                 struct xhci_event_cmd *event,
963                 union xhci_trb *trb)
964 {
965         int slot_id;
966         unsigned int ep_index;
967
968         slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]);
969         ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]);
970         /* This command will only fail if the endpoint wasn't halted,
971          * but we don't care.
972          */
973         xhci_dbg(xhci, "Ignoring reset ep completion code of %u\n",
974                         (unsigned int) GET_COMP_CODE(event->status));
975
976         /* HW with the reset endpoint quirk needs to have a configure endpoint
977          * command complete before the endpoint can be used.  Queue that here
978          * because the HW can't handle two commands being queued in a row.
979          */
980         if (xhci->quirks & XHCI_RESET_EP_QUIRK) {
981                 xhci_dbg(xhci, "Queueing configure endpoint command\n");
982                 xhci_queue_configure_endpoint(xhci,
983                                 xhci->devs[slot_id]->in_ctx->dma, slot_id,
984                                 false);
985                 xhci_ring_cmd_db(xhci);
986         } else {
987                 /* Clear our internal halted state and restart the ring(s) */
988                 xhci->devs[slot_id]->eps[ep_index].ep_state &= ~EP_HALTED;
989                 ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
990         }
991 }
992
993 /* Check to see if a command in the device's command queue matches this one.
994  * Signal the completion or free the command, and return 1.  Return 0 if the
995  * completed command isn't at the head of the command list.
996  */
997 static int handle_cmd_in_cmd_wait_list(struct xhci_hcd *xhci,
998                 struct xhci_virt_device *virt_dev,
999                 struct xhci_event_cmd *event)
1000 {
1001         struct xhci_command *command;
1002
1003         if (list_empty(&virt_dev->cmd_list))
1004                 return 0;
1005
1006         command = list_entry(virt_dev->cmd_list.next,
1007                         struct xhci_command, cmd_list);
1008         if (xhci->cmd_ring->dequeue != command->command_trb)
1009                 return 0;
1010
1011         command->status =
1012                 GET_COMP_CODE(event->status);
1013         list_del(&command->cmd_list);
1014         if (command->completion)
1015                 complete(command->completion);
1016         else
1017                 xhci_free_command(xhci, command);
1018         return 1;
1019 }
1020
1021 static void handle_cmd_completion(struct xhci_hcd *xhci,
1022                 struct xhci_event_cmd *event)
1023 {
1024         int slot_id = TRB_TO_SLOT_ID(event->flags);
1025         u64 cmd_dma;
1026         dma_addr_t cmd_dequeue_dma;
1027         struct xhci_input_control_ctx *ctrl_ctx;
1028         struct xhci_virt_device *virt_dev;
1029         unsigned int ep_index;
1030         struct xhci_ring *ep_ring;
1031         unsigned int ep_state;
1032
1033         cmd_dma = event->cmd_trb;
1034         cmd_dequeue_dma = xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg,
1035                         xhci->cmd_ring->dequeue);
1036         /* Is the command ring deq ptr out of sync with the deq seg ptr? */
1037         if (cmd_dequeue_dma == 0) {
1038                 xhci->error_bitmask |= 1 << 4;
1039                 return;
1040         }
1041         /* Does the DMA address match our internal dequeue pointer address? */
1042         if (cmd_dma != (u64) cmd_dequeue_dma) {
1043                 xhci->error_bitmask |= 1 << 5;
1044                 return;
1045         }
1046         switch (xhci->cmd_ring->dequeue->generic.field[3] & TRB_TYPE_BITMASK) {
1047         case TRB_TYPE(TRB_ENABLE_SLOT):
1048                 if (GET_COMP_CODE(event->status) == COMP_SUCCESS)
1049                         xhci->slot_id = slot_id;
1050                 else
1051                         xhci->slot_id = 0;
1052                 complete(&xhci->addr_dev);
1053                 break;
1054         case TRB_TYPE(TRB_DISABLE_SLOT):
1055                 if (xhci->devs[slot_id])
1056                         xhci_free_virt_device(xhci, slot_id);
1057                 break;
1058         case TRB_TYPE(TRB_CONFIG_EP):
1059                 virt_dev = xhci->devs[slot_id];
1060                 if (handle_cmd_in_cmd_wait_list(xhci, virt_dev, event))
1061                         break;
1062                 /*
1063                  * Configure endpoint commands can come from the USB core
1064                  * configuration or alt setting changes, or because the HW
1065                  * needed an extra configure endpoint command after a reset
1066                  * endpoint command or streams were being configured.
1067                  * If the command was for a halted endpoint, the xHCI driver
1068                  * is not waiting on the configure endpoint command.
1069                  */
1070                 ctrl_ctx = xhci_get_input_control_ctx(xhci,
1071                                 virt_dev->in_ctx);
1072                 /* Input ctx add_flags are the endpoint index plus one */
1073                 ep_index = xhci_last_valid_endpoint(ctrl_ctx->add_flags) - 1;
1074                 /* A usb_set_interface() call directly after clearing a halted
1075                  * condition may race on this quirky hardware.  Not worth
1076                  * worrying about, since this is prototype hardware.  Not sure
1077                  * if this will work for streams, but streams support was
1078                  * untested on this prototype.
1079                  */
1080                 if (xhci->quirks & XHCI_RESET_EP_QUIRK &&
1081                                 ep_index != (unsigned int) -1 &&
1082                                 ctrl_ctx->add_flags - SLOT_FLAG ==
1083                                         ctrl_ctx->drop_flags) {
1084                         ep_ring = xhci->devs[slot_id]->eps[ep_index].ring;
1085                         ep_state = xhci->devs[slot_id]->eps[ep_index].ep_state;
1086                         if (!(ep_state & EP_HALTED))
1087                                 goto bandwidth_change;
1088                         xhci_dbg(xhci, "Completed config ep cmd - "
1089                                         "last ep index = %d, state = %d\n",
1090                                         ep_index, ep_state);
1091                         /* Clear internal halted state and restart ring(s) */
1092                         xhci->devs[slot_id]->eps[ep_index].ep_state &=
1093                                 ~EP_HALTED;
1094                         ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
1095                         break;
1096                 }
1097 bandwidth_change:
1098                 xhci_dbg(xhci, "Completed config ep cmd\n");
1099                 xhci->devs[slot_id]->cmd_status =
1100                         GET_COMP_CODE(event->status);
1101                 complete(&xhci->devs[slot_id]->cmd_completion);
1102                 break;
1103         case TRB_TYPE(TRB_EVAL_CONTEXT):
1104                 virt_dev = xhci->devs[slot_id];
1105                 if (handle_cmd_in_cmd_wait_list(xhci, virt_dev, event))
1106                         break;
1107                 xhci->devs[slot_id]->cmd_status = GET_COMP_CODE(event->status);
1108                 complete(&xhci->devs[slot_id]->cmd_completion);
1109                 break;
1110         case TRB_TYPE(TRB_ADDR_DEV):
1111                 xhci->devs[slot_id]->cmd_status = GET_COMP_CODE(event->status);
1112                 complete(&xhci->addr_dev);
1113                 break;
1114         case TRB_TYPE(TRB_STOP_RING):
1115                 handle_stopped_endpoint(xhci, xhci->cmd_ring->dequeue, event);
1116                 break;
1117         case TRB_TYPE(TRB_SET_DEQ):
1118                 handle_set_deq_completion(xhci, event, xhci->cmd_ring->dequeue);
1119                 break;
1120         case TRB_TYPE(TRB_CMD_NOOP):
1121                 ++xhci->noops_handled;
1122                 break;
1123         case TRB_TYPE(TRB_RESET_EP):
1124                 handle_reset_ep_completion(xhci, event, xhci->cmd_ring->dequeue);
1125                 break;
1126         case TRB_TYPE(TRB_RESET_DEV):
1127                 xhci_dbg(xhci, "Completed reset device command.\n");
1128                 slot_id = TRB_TO_SLOT_ID(
1129                                 xhci->cmd_ring->dequeue->generic.field[3]);
1130                 virt_dev = xhci->devs[slot_id];
1131                 if (virt_dev)
1132                         handle_cmd_in_cmd_wait_list(xhci, virt_dev, event);
1133                 else
1134                         xhci_warn(xhci, "Reset device command completion "
1135                                         "for disabled slot %u\n", slot_id);
1136                 break;
1137         case TRB_TYPE(TRB_NEC_GET_FW):
1138                 if (!(xhci->quirks & XHCI_NEC_HOST)) {
1139                         xhci->error_bitmask |= 1 << 6;
1140                         break;
1141                 }
1142                 xhci_dbg(xhci, "NEC firmware version %2x.%02x\n",
1143                                 NEC_FW_MAJOR(event->status),
1144                                 NEC_FW_MINOR(event->status));
1145                 break;
1146         default:
1147                 /* Skip over unknown commands on the event ring */
1148                 xhci->error_bitmask |= 1 << 6;
1149                 break;
1150         }
1151         inc_deq(xhci, xhci->cmd_ring, false);
1152 }
1153
1154 static void handle_vendor_event(struct xhci_hcd *xhci,
1155                 union xhci_trb *event)
1156 {
1157         u32 trb_type;
1158
1159         trb_type = TRB_FIELD_TO_TYPE(event->generic.field[3]);
1160         xhci_dbg(xhci, "Vendor specific event TRB type = %u\n", trb_type);
1161         if (trb_type == TRB_NEC_CMD_COMP && (xhci->quirks & XHCI_NEC_HOST))
1162                 handle_cmd_completion(xhci, &event->event_cmd);
1163 }
1164
1165 static void handle_port_status(struct xhci_hcd *xhci,
1166                 union xhci_trb *event)
1167 {
1168         struct usb_hcd *hcd = xhci_to_hcd(xhci);
1169         u32 port_id;
1170         u32 temp, temp1;
1171         u32 __iomem *addr;
1172         int ports;
1173         int slot_id;
1174
1175         /* Port status change events always have a successful completion code */
1176         if (GET_COMP_CODE(event->generic.field[2]) != COMP_SUCCESS) {
1177                 xhci_warn(xhci, "WARN: xHC returned failed port status event\n");
1178                 xhci->error_bitmask |= 1 << 8;
1179         }
1180         port_id = GET_PORT_ID(event->generic.field[0]);
1181         xhci_dbg(xhci, "Port Status Change Event for port %d\n", port_id);
1182
1183         ports = HCS_MAX_PORTS(xhci->hcs_params1);
1184         if ((port_id <= 0) || (port_id > ports)) {
1185                 xhci_warn(xhci, "Invalid port id %d\n", port_id);
1186                 goto cleanup;
1187         }
1188
1189         addr = &xhci->op_regs->port_status_base + NUM_PORT_REGS * (port_id - 1);
1190         temp = xhci_readl(xhci, addr);
1191         if ((temp & PORT_CONNECT) && (hcd->state == HC_STATE_SUSPENDED)) {
1192                 xhci_dbg(xhci, "resume root hub\n");
1193                 usb_hcd_resume_root_hub(hcd);
1194         }
1195
1196         if ((temp & PORT_PLC) && (temp & PORT_PLS_MASK) == XDEV_RESUME) {
1197                 xhci_dbg(xhci, "port resume event for port %d\n", port_id);
1198
1199                 temp1 = xhci_readl(xhci, &xhci->op_regs->command);
1200                 if (!(temp1 & CMD_RUN)) {
1201                         xhci_warn(xhci, "xHC is not running.\n");
1202                         goto cleanup;
1203                 }
1204
1205                 if (DEV_SUPERSPEED(temp)) {
1206                         xhci_dbg(xhci, "resume SS port %d\n", port_id);
1207                         temp = xhci_port_state_to_neutral(temp);
1208                         temp &= ~PORT_PLS_MASK;
1209                         temp |= PORT_LINK_STROBE | XDEV_U0;
1210                         xhci_writel(xhci, temp, addr);
1211                         slot_id = xhci_find_slot_id_by_port(xhci, port_id);
1212                         if (!slot_id) {
1213                                 xhci_dbg(xhci, "slot_id is zero\n");
1214                                 goto cleanup;
1215                         }
1216                         xhci_ring_device(xhci, slot_id);
1217                         xhci_dbg(xhci, "resume SS port %d finished\n", port_id);
1218                         /* Clear PORT_PLC */
1219                         temp = xhci_readl(xhci, addr);
1220                         temp = xhci_port_state_to_neutral(temp);
1221                         temp |= PORT_PLC;
1222                         xhci_writel(xhci, temp, addr);
1223                 } else {
1224                         xhci_dbg(xhci, "resume HS port %d\n", port_id);
1225                         xhci->resume_done[port_id - 1] = jiffies +
1226                                 msecs_to_jiffies(20);
1227                         mod_timer(&hcd->rh_timer,
1228                                   xhci->resume_done[port_id - 1]);
1229                         /* Do the rest in GetPortStatus */
1230                 }
1231         }
1232
1233 cleanup:
1234         /* Update event ring dequeue pointer before dropping the lock */
1235         inc_deq(xhci, xhci->event_ring, true);
1236
1237         spin_unlock(&xhci->lock);
1238         /* Pass this up to the core */
1239         usb_hcd_poll_rh_status(xhci_to_hcd(xhci));
1240         spin_lock(&xhci->lock);
1241 }
1242
1243 /*
1244  * This TD is defined by the TRBs starting at start_trb in start_seg and ending
1245  * at end_trb, which may be in another segment.  If the suspect DMA address is a
1246  * TRB in this TD, this function returns that TRB's segment.  Otherwise it
1247  * returns 0.
1248  */
1249 struct xhci_segment *trb_in_td(struct xhci_segment *start_seg,
1250                 union xhci_trb  *start_trb,
1251                 union xhci_trb  *end_trb,
1252                 dma_addr_t      suspect_dma)
1253 {
1254         dma_addr_t start_dma;
1255         dma_addr_t end_seg_dma;
1256         dma_addr_t end_trb_dma;
1257         struct xhci_segment *cur_seg;
1258
1259         start_dma = xhci_trb_virt_to_dma(start_seg, start_trb);
1260         cur_seg = start_seg;
1261
1262         do {
1263                 if (start_dma == 0)
1264                         return NULL;
1265                 /* We may get an event for a Link TRB in the middle of a TD */
1266                 end_seg_dma = xhci_trb_virt_to_dma(cur_seg,
1267                                 &cur_seg->trbs[TRBS_PER_SEGMENT - 1]);
1268                 /* If the end TRB isn't in this segment, this is set to 0 */
1269                 end_trb_dma = xhci_trb_virt_to_dma(cur_seg, end_trb);
1270
1271                 if (end_trb_dma > 0) {
1272                         /* The end TRB is in this segment, so suspect should be here */
1273                         if (start_dma <= end_trb_dma) {
1274                                 if (suspect_dma >= start_dma && suspect_dma <= end_trb_dma)
1275                                         return cur_seg;
1276                         } else {
1277                                 /* Case for one segment with
1278                                  * a TD wrapped around to the top
1279                                  */
1280                                 if ((suspect_dma >= start_dma &&
1281                                                         suspect_dma <= end_seg_dma) ||
1282                                                 (suspect_dma >= cur_seg->dma &&
1283                                                  suspect_dma <= end_trb_dma))
1284                                         return cur_seg;
1285                         }
1286                         return NULL;
1287                 } else {
1288                         /* Might still be somewhere in this segment */
1289                         if (suspect_dma >= start_dma && suspect_dma <= end_seg_dma)
1290                                 return cur_seg;
1291                 }
1292                 cur_seg = cur_seg->next;
1293                 start_dma = xhci_trb_virt_to_dma(cur_seg, &cur_seg->trbs[0]);
1294         } while (cur_seg != start_seg);
1295
1296         return NULL;
1297 }
1298
1299 static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci,
1300                 unsigned int slot_id, unsigned int ep_index,
1301                 unsigned int stream_id,
1302                 struct xhci_td *td, union xhci_trb *event_trb)
1303 {
1304         struct xhci_virt_ep *ep = &xhci->devs[slot_id]->eps[ep_index];
1305         ep->ep_state |= EP_HALTED;
1306         ep->stopped_td = td;
1307         ep->stopped_trb = event_trb;
1308         ep->stopped_stream = stream_id;
1309
1310         xhci_queue_reset_ep(xhci, slot_id, ep_index);
1311         xhci_cleanup_stalled_ring(xhci, td->urb->dev, ep_index);
1312
1313         ep->stopped_td = NULL;
1314         ep->stopped_trb = NULL;
1315         ep->stopped_stream = 0;
1316
1317         xhci_ring_cmd_db(xhci);
1318 }
1319
1320 /* Check if an error has halted the endpoint ring.  The class driver will
1321  * cleanup the halt for a non-default control endpoint if we indicate a stall.
1322  * However, a babble and other errors also halt the endpoint ring, and the class
1323  * driver won't clear the halt in that case, so we need to issue a Set Transfer
1324  * Ring Dequeue Pointer command manually.
1325  */
1326 static int xhci_requires_manual_halt_cleanup(struct xhci_hcd *xhci,
1327                 struct xhci_ep_ctx *ep_ctx,
1328                 unsigned int trb_comp_code)
1329 {
1330         /* TRB completion codes that may require a manual halt cleanup */
1331         if (trb_comp_code == COMP_TX_ERR ||
1332                         trb_comp_code == COMP_BABBLE ||
1333                         trb_comp_code == COMP_SPLIT_ERR)
1334                 /* The 0.96 spec says a babbling control endpoint
1335                  * is not halted. The 0.96 spec says it is.  Some HW
1336                  * claims to be 0.95 compliant, but it halts the control
1337                  * endpoint anyway.  Check if a babble halted the
1338                  * endpoint.
1339                  */
1340                 if ((ep_ctx->ep_info & EP_STATE_MASK) == EP_STATE_HALTED)
1341                         return 1;
1342
1343         return 0;
1344 }
1345
1346 int xhci_is_vendor_info_code(struct xhci_hcd *xhci, unsigned int trb_comp_code)
1347 {
1348         if (trb_comp_code >= 224 && trb_comp_code <= 255) {
1349                 /* Vendor defined "informational" completion code,
1350                  * treat as not-an-error.
1351                  */
1352                 xhci_dbg(xhci, "Vendor defined info completion code %u\n",
1353                                 trb_comp_code);
1354                 xhci_dbg(xhci, "Treating code as success.\n");
1355                 return 1;
1356         }
1357         return 0;
1358 }
1359
1360 /*
1361  * Finish the td processing, remove the td from td list;
1362  * Return 1 if the urb can be given back.
1363  */
1364 static int finish_td(struct xhci_hcd *xhci, struct xhci_td *td,
1365         union xhci_trb *event_trb, struct xhci_transfer_event *event,
1366         struct xhci_virt_ep *ep, int *status, bool skip)
1367 {
1368         struct xhci_virt_device *xdev;
1369         struct xhci_ring *ep_ring;
1370         unsigned int slot_id;
1371         int ep_index;
1372         struct urb *urb = NULL;
1373         struct xhci_ep_ctx *ep_ctx;
1374         int ret = 0;
1375         struct urb_priv *urb_priv;
1376         u32 trb_comp_code;
1377
1378         slot_id = TRB_TO_SLOT_ID(event->flags);
1379         xdev = xhci->devs[slot_id];
1380         ep_index = TRB_TO_EP_ID(event->flags) - 1;
1381         ep_ring = xhci_dma_to_transfer_ring(ep, event->buffer);
1382         ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
1383         trb_comp_code = GET_COMP_CODE(event->transfer_len);
1384
1385         if (skip)
1386                 goto td_cleanup;
1387
1388         if (trb_comp_code == COMP_STOP_INVAL ||
1389                         trb_comp_code == COMP_STOP) {
1390                 /* The Endpoint Stop Command completion will take care of any
1391                  * stopped TDs.  A stopped TD may be restarted, so don't update
1392                  * the ring dequeue pointer or take this TD off any lists yet.
1393                  */
1394                 ep->stopped_td = td;
1395                 ep->stopped_trb = event_trb;
1396                 return 0;
1397         } else {
1398                 if (trb_comp_code == COMP_STALL) {
1399                         /* The transfer is completed from the driver's
1400                          * perspective, but we need to issue a set dequeue
1401                          * command for this stalled endpoint to move the dequeue
1402                          * pointer past the TD.  We can't do that here because
1403                          * the halt condition must be cleared first.  Let the
1404                          * USB class driver clear the stall later.
1405                          */
1406                         ep->stopped_td = td;
1407                         ep->stopped_trb = event_trb;
1408                         ep->stopped_stream = ep_ring->stream_id;
1409                 } else if (xhci_requires_manual_halt_cleanup(xhci,
1410                                         ep_ctx, trb_comp_code)) {
1411                         /* Other types of errors halt the endpoint, but the
1412                          * class driver doesn't call usb_reset_endpoint() unless
1413                          * the error is -EPIPE.  Clear the halted status in the
1414                          * xHCI hardware manually.
1415                          */
1416                         xhci_cleanup_halted_endpoint(xhci,
1417                                         slot_id, ep_index, ep_ring->stream_id,
1418                                         td, event_trb);
1419                 } else {
1420                         /* Update ring dequeue pointer */
1421                         while (ep_ring->dequeue != td->last_trb)
1422                                 inc_deq(xhci, ep_ring, false);
1423                         inc_deq(xhci, ep_ring, false);
1424                 }
1425
1426 td_cleanup:
1427                 /* Clean up the endpoint's TD list */
1428                 urb = td->urb;
1429                 urb_priv = urb->hcpriv;
1430
1431                 /* Do one last check of the actual transfer length.
1432                  * If the host controller said we transferred more data than
1433                  * the buffer length, urb->actual_length will be a very big
1434                  * number (since it's unsigned).  Play it safe and say we didn't
1435                  * transfer anything.
1436                  */
1437                 if (urb->actual_length > urb->transfer_buffer_length) {
1438                         xhci_warn(xhci, "URB transfer length is wrong, "
1439                                         "xHC issue? req. len = %u, "
1440                                         "act. len = %u\n",
1441                                         urb->transfer_buffer_length,
1442                                         urb->actual_length);
1443                         urb->actual_length = 0;
1444                         if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1445                                 *status = -EREMOTEIO;
1446                         else
1447                                 *status = 0;
1448                 }
1449                 list_del(&td->td_list);
1450                 /* Was this TD slated to be cancelled but completed anyway? */
1451                 if (!list_empty(&td->cancelled_td_list))
1452                         list_del(&td->cancelled_td_list);
1453
1454                 urb_priv->td_cnt++;
1455                 /* Giveback the urb when all the tds are completed */
1456                 if (urb_priv->td_cnt == urb_priv->length)
1457                         ret = 1;
1458         }
1459
1460         return ret;
1461 }
1462
1463 /*
1464  * Process control tds, update urb status and actual_length.
1465  */
1466 static int process_ctrl_td(struct xhci_hcd *xhci, struct xhci_td *td,
1467         union xhci_trb *event_trb, struct xhci_transfer_event *event,
1468         struct xhci_virt_ep *ep, int *status)
1469 {
1470         struct xhci_virt_device *xdev;
1471         struct xhci_ring *ep_ring;
1472         unsigned int slot_id;
1473         int ep_index;
1474         struct xhci_ep_ctx *ep_ctx;
1475         u32 trb_comp_code;
1476
1477         slot_id = TRB_TO_SLOT_ID(event->flags);
1478         xdev = xhci->devs[slot_id];
1479         ep_index = TRB_TO_EP_ID(event->flags) - 1;
1480         ep_ring = xhci_dma_to_transfer_ring(ep, event->buffer);
1481         ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
1482         trb_comp_code = GET_COMP_CODE(event->transfer_len);
1483
1484         xhci_debug_trb(xhci, xhci->event_ring->dequeue);
1485         switch (trb_comp_code) {
1486         case COMP_SUCCESS:
1487                 if (event_trb == ep_ring->dequeue) {
1488                         xhci_warn(xhci, "WARN: Success on ctrl setup TRB "
1489                                         "without IOC set??\n");
1490                         *status = -ESHUTDOWN;
1491                 } else if (event_trb != td->last_trb) {
1492                         xhci_warn(xhci, "WARN: Success on ctrl data TRB "
1493                                         "without IOC set??\n");
1494                         *status = -ESHUTDOWN;
1495                 } else {
1496                         xhci_dbg(xhci, "Successful control transfer!\n");
1497                         *status = 0;
1498                 }
1499                 break;
1500         case COMP_SHORT_TX:
1501                 xhci_warn(xhci, "WARN: short transfer on control ep\n");
1502                 if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1503                         *status = -EREMOTEIO;
1504                 else
1505                         *status = 0;
1506                 break;
1507         default:
1508                 if (!xhci_requires_manual_halt_cleanup(xhci,
1509                                         ep_ctx, trb_comp_code))
1510                         break;
1511                 xhci_dbg(xhci, "TRB error code %u, "
1512                                 "halted endpoint index = %u\n",
1513                                 trb_comp_code, ep_index);
1514                 /* else fall through */
1515         case COMP_STALL:
1516                 /* Did we transfer part of the data (middle) phase? */
1517                 if (event_trb != ep_ring->dequeue &&
1518                                 event_trb != td->last_trb)
1519                         td->urb->actual_length =
1520                                 td->urb->transfer_buffer_length
1521                                 - TRB_LEN(event->transfer_len);
1522                 else
1523                         td->urb->actual_length = 0;
1524
1525                 xhci_cleanup_halted_endpoint(xhci,
1526                         slot_id, ep_index, 0, td, event_trb);
1527                 return finish_td(xhci, td, event_trb, event, ep, status, true);
1528         }
1529         /*
1530          * Did we transfer any data, despite the errors that might have
1531          * happened?  I.e. did we get past the setup stage?
1532          */
1533         if (event_trb != ep_ring->dequeue) {
1534                 /* The event was for the status stage */
1535                 if (event_trb == td->last_trb) {
1536                         if (td->urb->actual_length != 0) {
1537                                 /* Don't overwrite a previously set error code
1538                                  */
1539                                 if ((*status == -EINPROGRESS || *status == 0) &&
1540                                                 (td->urb->transfer_flags
1541                                                  & URB_SHORT_NOT_OK))
1542                                         /* Did we already see a short data
1543                                          * stage? */
1544                                         *status = -EREMOTEIO;
1545                         } else {
1546                                 td->urb->actual_length =
1547                                         td->urb->transfer_buffer_length;
1548                         }
1549                 } else {
1550                 /* Maybe the event was for the data stage? */
1551                         if (trb_comp_code != COMP_STOP_INVAL) {
1552                                 /* We didn't stop on a link TRB in the middle */
1553                                 td->urb->actual_length =
1554                                         td->urb->transfer_buffer_length -
1555                                         TRB_LEN(event->transfer_len);
1556                                 xhci_dbg(xhci, "Waiting for status "
1557                                                 "stage event\n");
1558                                 return 0;
1559                         }
1560                 }
1561         }
1562
1563         return finish_td(xhci, td, event_trb, event, ep, status, false);
1564 }
1565
1566 /*
1567  * Process isochronous tds, update urb packet status and actual_length.
1568  */
1569 static int process_isoc_td(struct xhci_hcd *xhci, struct xhci_td *td,
1570         union xhci_trb *event_trb, struct xhci_transfer_event *event,
1571         struct xhci_virt_ep *ep, int *status)
1572 {
1573         struct xhci_ring *ep_ring;
1574         struct urb_priv *urb_priv;
1575         int idx;
1576         int len = 0;
1577         int skip_td = 0;
1578         union xhci_trb *cur_trb;
1579         struct xhci_segment *cur_seg;
1580         u32 trb_comp_code;
1581
1582         ep_ring = xhci_dma_to_transfer_ring(ep, event->buffer);
1583         trb_comp_code = GET_COMP_CODE(event->transfer_len);
1584         urb_priv = td->urb->hcpriv;
1585         idx = urb_priv->td_cnt;
1586
1587         if (ep->skip) {
1588                 /* The transfer is partly done */
1589                 *status = -EXDEV;
1590                 td->urb->iso_frame_desc[idx].status = -EXDEV;
1591         } else {
1592                 /* handle completion code */
1593                 switch (trb_comp_code) {
1594                 case COMP_SUCCESS:
1595                         td->urb->iso_frame_desc[idx].status = 0;
1596                         xhci_dbg(xhci, "Successful isoc transfer!\n");
1597                         break;
1598                 case COMP_SHORT_TX:
1599                         if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1600                                 td->urb->iso_frame_desc[idx].status =
1601                                          -EREMOTEIO;
1602                         else
1603                                 td->urb->iso_frame_desc[idx].status = 0;
1604                         break;
1605                 case COMP_BW_OVER:
1606                         td->urb->iso_frame_desc[idx].status = -ECOMM;
1607                         skip_td = 1;
1608                         break;
1609                 case COMP_BUFF_OVER:
1610                 case COMP_BABBLE:
1611                         td->urb->iso_frame_desc[idx].status = -EOVERFLOW;
1612                         skip_td = 1;
1613                         break;
1614                 case COMP_STALL:
1615                         td->urb->iso_frame_desc[idx].status = -EPROTO;
1616                         skip_td = 1;
1617                         break;
1618                 case COMP_STOP:
1619                 case COMP_STOP_INVAL:
1620                         break;
1621                 default:
1622                         td->urb->iso_frame_desc[idx].status = -1;
1623                         break;
1624                 }
1625         }
1626
1627         /* calc actual length */
1628         if (ep->skip) {
1629                 td->urb->iso_frame_desc[idx].actual_length = 0;
1630                 /* Update ring dequeue pointer */
1631                 while (ep_ring->dequeue != td->last_trb)
1632                         inc_deq(xhci, ep_ring, false);
1633                 inc_deq(xhci, ep_ring, false);
1634                 return finish_td(xhci, td, event_trb, event, ep, status, true);
1635         }
1636
1637         if (trb_comp_code == COMP_SUCCESS || skip_td == 1) {
1638                 td->urb->iso_frame_desc[idx].actual_length =
1639                         td->urb->iso_frame_desc[idx].length;
1640                 td->urb->actual_length +=
1641                         td->urb->iso_frame_desc[idx].length;
1642         } else {
1643                 for (cur_trb = ep_ring->dequeue,
1644                      cur_seg = ep_ring->deq_seg; cur_trb != event_trb;
1645                      next_trb(xhci, ep_ring, &cur_seg, &cur_trb)) {
1646                         if ((cur_trb->generic.field[3] &
1647                          TRB_TYPE_BITMASK) != TRB_TYPE(TRB_TR_NOOP) &&
1648                             (cur_trb->generic.field[3] &
1649                          TRB_TYPE_BITMASK) != TRB_TYPE(TRB_LINK))
1650                                 len +=
1651                                     TRB_LEN(cur_trb->generic.field[2]);
1652                 }
1653                 len += TRB_LEN(cur_trb->generic.field[2]) -
1654                         TRB_LEN(event->transfer_len);
1655
1656                 if (trb_comp_code != COMP_STOP_INVAL) {
1657                         td->urb->iso_frame_desc[idx].actual_length = len;
1658                         td->urb->actual_length += len;
1659                 }
1660         }
1661
1662         if ((idx == urb_priv->length - 1) && *status == -EINPROGRESS)
1663                 *status = 0;
1664
1665         return finish_td(xhci, td, event_trb, event, ep, status, false);
1666 }
1667
1668 /*
1669  * Process bulk and interrupt tds, update urb status and actual_length.
1670  */
1671 static int process_bulk_intr_td(struct xhci_hcd *xhci, struct xhci_td *td,
1672         union xhci_trb *event_trb, struct xhci_transfer_event *event,
1673         struct xhci_virt_ep *ep, int *status)
1674 {
1675         struct xhci_ring *ep_ring;
1676         union xhci_trb *cur_trb;
1677         struct xhci_segment *cur_seg;
1678         u32 trb_comp_code;
1679
1680         ep_ring = xhci_dma_to_transfer_ring(ep, event->buffer);
1681         trb_comp_code = GET_COMP_CODE(event->transfer_len);
1682
1683         switch (trb_comp_code) {
1684         case COMP_SUCCESS:
1685                 /* Double check that the HW transferred everything. */
1686                 if (event_trb != td->last_trb) {
1687                         xhci_warn(xhci, "WARN Successful completion "
1688                                         "on short TX\n");
1689                         if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1690                                 *status = -EREMOTEIO;
1691                         else
1692                                 *status = 0;
1693                 } else {
1694                         if (usb_endpoint_xfer_bulk(&td->urb->ep->desc))
1695                                 xhci_dbg(xhci, "Successful bulk "
1696                                                 "transfer!\n");
1697                         else
1698                                 xhci_dbg(xhci, "Successful interrupt "
1699                                                 "transfer!\n");
1700                         *status = 0;
1701                 }
1702                 break;
1703         case COMP_SHORT_TX:
1704                 if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1705                         *status = -EREMOTEIO;
1706                 else
1707                         *status = 0;
1708                 break;
1709         default:
1710                 /* Others already handled above */
1711                 break;
1712         }
1713         dev_dbg(&td->urb->dev->dev,
1714                         "ep %#x - asked for %d bytes, "
1715                         "%d bytes untransferred\n",
1716                         td->urb->ep->desc.bEndpointAddress,
1717                         td->urb->transfer_buffer_length,
1718                         TRB_LEN(event->transfer_len));
1719         /* Fast path - was this the last TRB in the TD for this URB? */
1720         if (event_trb == td->last_trb) {
1721                 if (TRB_LEN(event->transfer_len) != 0) {
1722                         td->urb->actual_length =
1723                                 td->urb->transfer_buffer_length -
1724                                 TRB_LEN(event->transfer_len);
1725                         if (td->urb->transfer_buffer_length <
1726                                         td->urb->actual_length) {
1727                                 xhci_warn(xhci, "HC gave bad length "
1728                                                 "of %d bytes left\n",
1729                                                 TRB_LEN(event->transfer_len));
1730                                 td->urb->actual_length = 0;
1731                                 if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1732                                         *status = -EREMOTEIO;
1733                                 else
1734                                         *status = 0;
1735                         }
1736                         /* Don't overwrite a previously set error code */
1737                         if (*status == -EINPROGRESS) {
1738                                 if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1739                                         *status = -EREMOTEIO;
1740                                 else
1741                                         *status = 0;
1742                         }
1743                 } else {
1744                         td->urb->actual_length =
1745                                 td->urb->transfer_buffer_length;
1746                         /* Ignore a short packet completion if the
1747                          * untransferred length was zero.
1748                          */
1749                         if (*status == -EREMOTEIO)
1750                                 *status = 0;
1751                 }
1752         } else {
1753                 /* Slow path - walk the list, starting from the dequeue
1754                  * pointer, to get the actual length transferred.
1755                  */
1756                 td->urb->actual_length = 0;
1757                 for (cur_trb = ep_ring->dequeue, cur_seg = ep_ring->deq_seg;
1758                                 cur_trb != event_trb;
1759                                 next_trb(xhci, ep_ring, &cur_seg, &cur_trb)) {
1760                         if ((cur_trb->generic.field[3] &
1761                          TRB_TYPE_BITMASK) != TRB_TYPE(TRB_TR_NOOP) &&
1762                             (cur_trb->generic.field[3] &
1763                          TRB_TYPE_BITMASK) != TRB_TYPE(TRB_LINK))
1764                                 td->urb->actual_length +=
1765                                         TRB_LEN(cur_trb->generic.field[2]);
1766                 }
1767                 /* If the ring didn't stop on a Link or No-op TRB, add
1768                  * in the actual bytes transferred from the Normal TRB
1769                  */
1770                 if (trb_comp_code != COMP_STOP_INVAL)
1771                         td->urb->actual_length +=
1772                                 TRB_LEN(cur_trb->generic.field[2]) -
1773                                 TRB_LEN(event->transfer_len);
1774         }
1775
1776         return finish_td(xhci, td, event_trb, event, ep, status, false);
1777 }
1778
1779 /*
1780  * If this function returns an error condition, it means it got a Transfer
1781  * event with a corrupted Slot ID, Endpoint ID, or TRB DMA address.
1782  * At this point, the host controller is probably hosed and should be reset.
1783  */
1784 static int handle_tx_event(struct xhci_hcd *xhci,
1785                 struct xhci_transfer_event *event)
1786 {
1787         struct xhci_virt_device *xdev;
1788         struct xhci_virt_ep *ep;
1789         struct xhci_ring *ep_ring;
1790         unsigned int slot_id;
1791         int ep_index;
1792         struct xhci_td *td = NULL;
1793         dma_addr_t event_dma;
1794         struct xhci_segment *event_seg;
1795         union xhci_trb *event_trb;
1796         struct urb *urb = NULL;
1797         int status = -EINPROGRESS;
1798         struct urb_priv *urb_priv;
1799         struct xhci_ep_ctx *ep_ctx;
1800         u32 trb_comp_code;
1801         int ret = 0;
1802
1803         slot_id = TRB_TO_SLOT_ID(event->flags);
1804         xdev = xhci->devs[slot_id];
1805         if (!xdev) {
1806                 xhci_err(xhci, "ERROR Transfer event pointed to bad slot\n");
1807                 return -ENODEV;
1808         }
1809
1810         /* Endpoint ID is 1 based, our index is zero based */
1811         ep_index = TRB_TO_EP_ID(event->flags) - 1;
1812         xhci_dbg(xhci, "%s - ep index = %d\n", __func__, ep_index);
1813         ep = &xdev->eps[ep_index];
1814         ep_ring = xhci_dma_to_transfer_ring(ep, event->buffer);
1815         ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
1816         if (!ep_ring ||
1817                 (ep_ctx->ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) {
1818                 xhci_err(xhci, "ERROR Transfer event for disabled endpoint "
1819                                 "or incorrect stream ring\n");
1820                 return -ENODEV;
1821         }
1822
1823         event_dma = event->buffer;
1824         trb_comp_code = GET_COMP_CODE(event->transfer_len);
1825         /* Look for common error cases */
1826         switch (trb_comp_code) {
1827         /* Skip codes that require special handling depending on
1828          * transfer type
1829          */
1830         case COMP_SUCCESS:
1831         case COMP_SHORT_TX:
1832                 break;
1833         case COMP_STOP:
1834                 xhci_dbg(xhci, "Stopped on Transfer TRB\n");
1835                 break;
1836         case COMP_STOP_INVAL:
1837                 xhci_dbg(xhci, "Stopped on No-op or Link TRB\n");
1838                 break;
1839         case COMP_STALL:
1840                 xhci_warn(xhci, "WARN: Stalled endpoint\n");
1841                 ep->ep_state |= EP_HALTED;
1842                 status = -EPIPE;
1843                 break;
1844         case COMP_TRB_ERR:
1845                 xhci_warn(xhci, "WARN: TRB error on endpoint\n");
1846                 status = -EILSEQ;
1847                 break;
1848         case COMP_SPLIT_ERR:
1849         case COMP_TX_ERR:
1850                 xhci_warn(xhci, "WARN: transfer error on endpoint\n");
1851                 status = -EPROTO;
1852                 break;
1853         case COMP_BABBLE:
1854                 xhci_warn(xhci, "WARN: babble error on endpoint\n");
1855                 status = -EOVERFLOW;
1856                 break;
1857         case COMP_DB_ERR:
1858                 xhci_warn(xhci, "WARN: HC couldn't access mem fast enough\n");
1859                 status = -ENOSR;
1860                 break;
1861         case COMP_BW_OVER:
1862                 xhci_warn(xhci, "WARN: bandwidth overrun event on endpoint\n");
1863                 break;
1864         case COMP_BUFF_OVER:
1865                 xhci_warn(xhci, "WARN: buffer overrun event on endpoint\n");
1866                 break;
1867         case COMP_UNDERRUN:
1868                 /*
1869                  * When the Isoch ring is empty, the xHC will generate
1870                  * a Ring Overrun Event for IN Isoch endpoint or Ring
1871                  * Underrun Event for OUT Isoch endpoint.
1872                  */
1873                 xhci_dbg(xhci, "underrun event on endpoint\n");
1874                 if (!list_empty(&ep_ring->td_list))
1875                         xhci_dbg(xhci, "Underrun Event for slot %d ep %d "
1876                                         "still with TDs queued?\n",
1877                                 TRB_TO_SLOT_ID(event->flags), ep_index);
1878                 goto cleanup;
1879         case COMP_OVERRUN:
1880                 xhci_dbg(xhci, "overrun event on endpoint\n");
1881                 if (!list_empty(&ep_ring->td_list))
1882                         xhci_dbg(xhci, "Overrun Event for slot %d ep %d "
1883                                         "still with TDs queued?\n",
1884                                 TRB_TO_SLOT_ID(event->flags), ep_index);
1885                 goto cleanup;
1886         case COMP_MISSED_INT:
1887                 /*
1888                  * When encounter missed service error, one or more isoc tds
1889                  * may be missed by xHC.
1890                  * Set skip flag of the ep_ring; Complete the missed tds as
1891                  * short transfer when process the ep_ring next time.
1892                  */
1893                 ep->skip = true;
1894                 xhci_dbg(xhci, "Miss service interval error, set skip flag\n");
1895                 goto cleanup;
1896         default:
1897                 if (xhci_is_vendor_info_code(xhci, trb_comp_code)) {
1898                         status = 0;
1899                         break;
1900                 }
1901                 xhci_warn(xhci, "ERROR Unknown event condition, HC probably "
1902                                 "busted\n");
1903                 goto cleanup;
1904         }
1905
1906         do {
1907                 /* This TRB should be in the TD at the head of this ring's
1908                  * TD list.
1909                  */
1910                 if (list_empty(&ep_ring->td_list)) {
1911                         xhci_warn(xhci, "WARN Event TRB for slot %d ep %d "
1912                                         "with no TDs queued?\n",
1913                                   TRB_TO_SLOT_ID(event->flags), ep_index);
1914                         xhci_dbg(xhci, "Event TRB with TRB type ID %u\n",
1915                           (unsigned int) (event->flags & TRB_TYPE_BITMASK)>>10);
1916                         xhci_print_trb_offsets(xhci, (union xhci_trb *) event);
1917                         if (ep->skip) {
1918                                 ep->skip = false;
1919                                 xhci_dbg(xhci, "td_list is empty while skip "
1920                                                 "flag set. Clear skip flag.\n");
1921                         }
1922                         ret = 0;
1923                         goto cleanup;
1924                 }
1925
1926                 td = list_entry(ep_ring->td_list.next, struct xhci_td, td_list);
1927                 /* Is this a TRB in the currently executing TD? */
1928                 event_seg = trb_in_td(ep_ring->deq_seg, ep_ring->dequeue,
1929                                 td->last_trb, event_dma);
1930                 if (event_seg && ep->skip) {
1931                         xhci_dbg(xhci, "Found td. Clear skip flag.\n");
1932                         ep->skip = false;
1933                 }
1934                 if (!event_seg &&
1935                    (!ep->skip || !usb_endpoint_xfer_isoc(&td->urb->ep->desc))) {
1936                         /* HC is busted, give up! */
1937                         xhci_err(xhci, "ERROR Transfer event TRB DMA ptr not "
1938                                         "part of current TD\n");
1939                         return -ESHUTDOWN;
1940                 }
1941
1942                 if (event_seg) {
1943                         event_trb = &event_seg->trbs[(event_dma -
1944                                          event_seg->dma) / sizeof(*event_trb)];
1945                         /*
1946                          * No-op TRB should not trigger interrupts.
1947                          * If event_trb is a no-op TRB, it means the
1948                          * corresponding TD has been cancelled. Just ignore
1949                          * the TD.
1950                          */
1951                         if ((event_trb->generic.field[3] & TRB_TYPE_BITMASK)
1952                                          == TRB_TYPE(TRB_TR_NOOP)) {
1953                                 xhci_dbg(xhci, "event_trb is a no-op TRB. "
1954                                                 "Skip it\n");
1955                                 goto cleanup;
1956                         }
1957                 }
1958
1959                 /* Now update the urb's actual_length and give back to
1960                  * the core
1961                  */
1962                 if (usb_endpoint_xfer_control(&td->urb->ep->desc))
1963                         ret = process_ctrl_td(xhci, td, event_trb, event, ep,
1964                                                  &status);
1965                 else if (usb_endpoint_xfer_isoc(&td->urb->ep->desc))
1966                         ret = process_isoc_td(xhci, td, event_trb, event, ep,
1967                                                  &status);
1968                 else
1969                         ret = process_bulk_intr_td(xhci, td, event_trb, event,
1970                                                  ep, &status);
1971
1972 cleanup:
1973                 /*
1974                  * Do not update event ring dequeue pointer if ep->skip is set.
1975                  * Will roll back to continue process missed tds.
1976                  */
1977                 if (trb_comp_code == COMP_MISSED_INT || !ep->skip) {
1978                         inc_deq(xhci, xhci->event_ring, true);
1979                 }
1980
1981                 if (ret) {
1982                         urb = td->urb;
1983                         urb_priv = urb->hcpriv;
1984                         /* Leave the TD around for the reset endpoint function
1985                          * to use(but only if it's not a control endpoint,
1986                          * since we already queued the Set TR dequeue pointer
1987                          * command for stalled control endpoints).
1988                          */
1989                         if (usb_endpoint_xfer_control(&urb->ep->desc) ||
1990                                 (trb_comp_code != COMP_STALL &&
1991                                         trb_comp_code != COMP_BABBLE))
1992                                 xhci_urb_free_priv(xhci, urb_priv);
1993
1994                         usb_hcd_unlink_urb_from_ep(xhci_to_hcd(xhci), urb);
1995                         xhci_dbg(xhci, "Giveback URB %p, len = %d, "
1996                                         "status = %d\n",
1997                                         urb, urb->actual_length, status);
1998                         spin_unlock(&xhci->lock);
1999                         usb_hcd_giveback_urb(xhci_to_hcd(xhci), urb, status);
2000                         spin_lock(&xhci->lock);
2001                 }
2002
2003         /*
2004          * If ep->skip is set, it means there are missed tds on the
2005          * endpoint ring need to take care of.
2006          * Process them as short transfer until reach the td pointed by
2007          * the event.
2008          */
2009         } while (ep->skip && trb_comp_code != COMP_MISSED_INT);
2010
2011         return 0;
2012 }
2013
2014 /*
2015  * This function handles all OS-owned events on the event ring.  It may drop
2016  * xhci->lock between event processing (e.g. to pass up port status changes).
2017  */
2018 static void xhci_handle_event(struct xhci_hcd *xhci)
2019 {
2020         union xhci_trb *event;
2021         int update_ptrs = 1;
2022         int ret;
2023
2024         xhci_dbg(xhci, "In %s\n", __func__);
2025         if (!xhci->event_ring || !xhci->event_ring->dequeue) {
2026                 xhci->error_bitmask |= 1 << 1;
2027                 return;
2028         }
2029
2030         event = xhci->event_ring->dequeue;
2031         /* Does the HC or OS own the TRB? */
2032         if ((event->event_cmd.flags & TRB_CYCLE) !=
2033                         xhci->event_ring->cycle_state) {
2034                 xhci->error_bitmask |= 1 << 2;
2035                 return;
2036         }
2037         xhci_dbg(xhci, "%s - OS owns TRB\n", __func__);
2038
2039         /* FIXME: Handle more event types. */
2040         switch ((event->event_cmd.flags & TRB_TYPE_BITMASK)) {
2041         case TRB_TYPE(TRB_COMPLETION):
2042                 xhci_dbg(xhci, "%s - calling handle_cmd_completion\n", __func__);
2043                 handle_cmd_completion(xhci, &event->event_cmd);
2044                 xhci_dbg(xhci, "%s - returned from handle_cmd_completion\n", __func__);
2045                 break;
2046         case TRB_TYPE(TRB_PORT_STATUS):
2047                 xhci_dbg(xhci, "%s - calling handle_port_status\n", __func__);
2048                 handle_port_status(xhci, event);
2049                 xhci_dbg(xhci, "%s - returned from handle_port_status\n", __func__);
2050                 update_ptrs = 0;
2051                 break;
2052         case TRB_TYPE(TRB_TRANSFER):
2053                 xhci_dbg(xhci, "%s - calling handle_tx_event\n", __func__);
2054                 ret = handle_tx_event(xhci, &event->trans_event);
2055                 xhci_dbg(xhci, "%s - returned from handle_tx_event\n", __func__);
2056                 if (ret < 0)
2057                         xhci->error_bitmask |= 1 << 9;
2058                 else
2059                         update_ptrs = 0;
2060                 break;
2061         default:
2062                 if ((event->event_cmd.flags & TRB_TYPE_BITMASK) >= TRB_TYPE(48))
2063                         handle_vendor_event(xhci, event);
2064                 else
2065                         xhci->error_bitmask |= 1 << 3;
2066         }
2067         /* Any of the above functions may drop and re-acquire the lock, so check
2068          * to make sure a watchdog timer didn't mark the host as non-responsive.
2069          */
2070         if (xhci->xhc_state & XHCI_STATE_DYING) {
2071                 xhci_dbg(xhci, "xHCI host dying, returning from "
2072                                 "event handler.\n");
2073                 return;
2074         }
2075
2076         if (update_ptrs)
2077                 /* Update SW event ring dequeue pointer */
2078                 inc_deq(xhci, xhci->event_ring, true);
2079
2080         /* Are there more items on the event ring? */
2081         xhci_handle_event(xhci);
2082 }
2083
2084 /*
2085  * xHCI spec says we can get an interrupt, and if the HC has an error condition,
2086  * we might get bad data out of the event ring.  Section 4.10.2.7 has a list of
2087  * indicators of an event TRB error, but we check the status *first* to be safe.
2088  */
2089 irqreturn_t xhci_irq(struct usb_hcd *hcd)
2090 {
2091         struct xhci_hcd *xhci = hcd_to_xhci(hcd);
2092         u32 status;
2093         union xhci_trb *trb;
2094         u64 temp_64;
2095         union xhci_trb *event_ring_deq;
2096         dma_addr_t deq;
2097
2098         spin_lock(&xhci->lock);
2099         trb = xhci->event_ring->dequeue;
2100         /* Check if the xHC generated the interrupt, or the irq is shared */
2101         status = xhci_readl(xhci, &xhci->op_regs->status);
2102         if (status == 0xffffffff)
2103                 goto hw_died;
2104
2105         if (!(status & STS_EINT)) {
2106                 spin_unlock(&xhci->lock);
2107                 return IRQ_NONE;
2108         }
2109         xhci_dbg(xhci, "op reg status = %08x\n", status);
2110         xhci_dbg(xhci, "Event ring dequeue ptr:\n");
2111         xhci_dbg(xhci, "@%llx %08x %08x %08x %08x\n",
2112                         (unsigned long long)
2113                         xhci_trb_virt_to_dma(xhci->event_ring->deq_seg, trb),
2114                         lower_32_bits(trb->link.segment_ptr),
2115                         upper_32_bits(trb->link.segment_ptr),
2116                         (unsigned int) trb->link.intr_target,
2117                         (unsigned int) trb->link.control);
2118
2119         if (status & STS_FATAL) {
2120                 xhci_warn(xhci, "WARNING: Host System Error\n");
2121                 xhci_halt(xhci);
2122 hw_died:
2123                 xhci_to_hcd(xhci)->state = HC_STATE_HALT;
2124                 spin_unlock(&xhci->lock);
2125                 return -ESHUTDOWN;
2126         }
2127
2128         /*
2129          * Clear the op reg interrupt status first,
2130          * so we can receive interrupts from other MSI-X interrupters.
2131          * Write 1 to clear the interrupt status.
2132          */
2133         status |= STS_EINT;
2134         xhci_writel(xhci, status, &xhci->op_regs->status);
2135         /* FIXME when MSI-X is supported and there are multiple vectors */
2136         /* Clear the MSI-X event interrupt status */
2137
2138         if (hcd->irq != -1) {
2139                 u32 irq_pending;
2140                 /* Acknowledge the PCI interrupt */
2141                 irq_pending = xhci_readl(xhci, &xhci->ir_set->irq_pending);
2142                 irq_pending |= 0x3;
2143                 xhci_writel(xhci, irq_pending, &xhci->ir_set->irq_pending);
2144         }
2145
2146         if (xhci->xhc_state & XHCI_STATE_DYING) {
2147                 xhci_dbg(xhci, "xHCI dying, ignoring interrupt. "
2148                                 "Shouldn't IRQs be disabled?\n");
2149                 /* Clear the event handler busy flag (RW1C);
2150                  * the event ring should be empty.
2151                  */
2152                 temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
2153                 xhci_write_64(xhci, temp_64 | ERST_EHB,
2154                                 &xhci->ir_set->erst_dequeue);
2155                 spin_unlock(&xhci->lock);
2156
2157                 return IRQ_HANDLED;
2158         }
2159
2160         event_ring_deq = xhci->event_ring->dequeue;
2161         /* FIXME this should be a delayed service routine
2162          * that clears the EHB.
2163          */
2164         xhci_handle_event(xhci);
2165
2166         temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
2167         /* If necessary, update the HW's version of the event ring deq ptr. */
2168         if (event_ring_deq != xhci->event_ring->dequeue) {
2169                 deq = xhci_trb_virt_to_dma(xhci->event_ring->deq_seg,
2170                                 xhci->event_ring->dequeue);
2171                 if (deq == 0)
2172                         xhci_warn(xhci, "WARN something wrong with SW event "
2173                                         "ring dequeue ptr.\n");
2174                 /* Update HC event ring dequeue pointer */
2175                 temp_64 &= ERST_PTR_MASK;
2176                 temp_64 |= ((u64) deq & (u64) ~ERST_PTR_MASK);
2177         }
2178
2179         /* Clear the event handler busy flag (RW1C); event ring is empty. */
2180         temp_64 |= ERST_EHB;
2181         xhci_write_64(xhci, temp_64, &xhci->ir_set->erst_dequeue);
2182
2183         spin_unlock(&xhci->lock);
2184
2185         return IRQ_HANDLED;
2186 }
2187
2188 irqreturn_t xhci_msi_irq(int irq, struct usb_hcd *hcd)
2189 {
2190         irqreturn_t ret;
2191
2192         set_bit(HCD_FLAG_SAW_IRQ, &hcd->flags);
2193
2194         ret = xhci_irq(hcd);
2195
2196         return ret;
2197 }
2198
2199 /****           Endpoint Ring Operations        ****/
2200
2201 /*
2202  * Generic function for queueing a TRB on a ring.
2203  * The caller must have checked to make sure there's room on the ring.
2204  *
2205  * @more_trbs_coming:   Will you enqueue more TRBs before calling
2206  *                      prepare_transfer()?
2207  */
2208 static void queue_trb(struct xhci_hcd *xhci, struct xhci_ring *ring,
2209                 bool consumer, bool more_trbs_coming,
2210                 u32 field1, u32 field2, u32 field3, u32 field4)
2211 {
2212         struct xhci_generic_trb *trb;
2213
2214         trb = &ring->enqueue->generic;
2215         trb->field[0] = field1;
2216         trb->field[1] = field2;
2217         trb->field[2] = field3;
2218         trb->field[3] = field4;
2219         inc_enq(xhci, ring, consumer, more_trbs_coming);
2220 }
2221
2222 /*
2223  * Does various checks on the endpoint ring, and makes it ready to queue num_trbs.
2224  * FIXME allocate segments if the ring is full.
2225  */
2226 static int prepare_ring(struct xhci_hcd *xhci, struct xhci_ring *ep_ring,
2227                 u32 ep_state, unsigned int num_trbs, gfp_t mem_flags)
2228 {
2229         /* Make sure the endpoint has been added to xHC schedule */
2230         xhci_dbg(xhci, "Endpoint state = 0x%x\n", ep_state);
2231         switch (ep_state) {
2232         case EP_STATE_DISABLED:
2233                 /*
2234                  * USB core changed config/interfaces without notifying us,
2235                  * or hardware is reporting the wrong state.
2236                  */
2237                 xhci_warn(xhci, "WARN urb submitted to disabled ep\n");
2238                 return -ENOENT;
2239         case EP_STATE_ERROR:
2240                 xhci_warn(xhci, "WARN waiting for error on ep to be cleared\n");
2241                 /* FIXME event handling code for error needs to clear it */
2242                 /* XXX not sure if this should be -ENOENT or not */
2243                 return -EINVAL;
2244         case EP_STATE_HALTED:
2245                 xhci_dbg(xhci, "WARN halted endpoint, queueing URB anyway.\n");
2246         case EP_STATE_STOPPED:
2247         case EP_STATE_RUNNING:
2248                 break;
2249         default:
2250                 xhci_err(xhci, "ERROR unknown endpoint state for ep\n");
2251                 /*
2252                  * FIXME issue Configure Endpoint command to try to get the HC
2253                  * back into a known state.
2254                  */
2255                 return -EINVAL;
2256         }
2257         if (!room_on_ring(xhci, ep_ring, num_trbs)) {
2258                 /* FIXME allocate more room */
2259                 xhci_err(xhci, "ERROR no room on ep ring\n");
2260                 return -ENOMEM;
2261         }
2262
2263         if (enqueue_is_link_trb(ep_ring)) {
2264                 struct xhci_ring *ring = ep_ring;
2265                 union xhci_trb *next;
2266
2267                 xhci_dbg(xhci, "prepare_ring: pointing to link trb\n");
2268                 next = ring->enqueue;
2269
2270                 while (last_trb(xhci, ring, ring->enq_seg, next)) {
2271
2272                         /* If we're not dealing with 0.95 hardware,
2273                          * clear the chain bit.
2274                          */
2275                         if (!xhci_link_trb_quirk(xhci))
2276                                 next->link.control &= ~TRB_CHAIN;
2277                         else
2278                                 next->link.control |= TRB_CHAIN;
2279
2280                         wmb();
2281                         next->link.control ^= (u32) TRB_CYCLE;
2282
2283                         /* Toggle the cycle bit after the last ring segment. */
2284                         if (last_trb_on_last_seg(xhci, ring, ring->enq_seg, next)) {
2285                                 ring->cycle_state = (ring->cycle_state ? 0 : 1);
2286                                 if (!in_interrupt()) {
2287                                         xhci_dbg(xhci, "queue_trb: Toggle cycle "
2288                                                 "state for ring %p = %i\n",
2289                                                 ring, (unsigned int)ring->cycle_state);
2290                                 }
2291                         }
2292                         ring->enq_seg = ring->enq_seg->next;
2293                         ring->enqueue = ring->enq_seg->trbs;
2294                         next = ring->enqueue;
2295                 }
2296         }
2297
2298         return 0;
2299 }
2300
2301 static int prepare_transfer(struct xhci_hcd *xhci,
2302                 struct xhci_virt_device *xdev,
2303                 unsigned int ep_index,
2304                 unsigned int stream_id,
2305                 unsigned int num_trbs,
2306                 struct urb *urb,
2307                 unsigned int td_index,
2308                 gfp_t mem_flags)
2309 {
2310         int ret;
2311         struct urb_priv *urb_priv;
2312         struct xhci_td  *td;
2313         struct xhci_ring *ep_ring;
2314         struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
2315
2316         ep_ring = xhci_stream_id_to_ring(xdev, ep_index, stream_id);
2317         if (!ep_ring) {
2318                 xhci_dbg(xhci, "Can't prepare ring for bad stream ID %u\n",
2319                                 stream_id);
2320                 return -EINVAL;
2321         }
2322
2323         ret = prepare_ring(xhci, ep_ring,
2324                         ep_ctx->ep_info & EP_STATE_MASK,
2325                         num_trbs, mem_flags);
2326         if (ret)
2327                 return ret;
2328
2329         urb_priv = urb->hcpriv;
2330         td = urb_priv->td[td_index];
2331
2332         INIT_LIST_HEAD(&td->td_list);
2333         INIT_LIST_HEAD(&td->cancelled_td_list);
2334
2335         if (td_index == 0) {
2336                 ret = usb_hcd_link_urb_to_ep(xhci_to_hcd(xhci), urb);
2337                 if (unlikely(ret)) {
2338                         xhci_urb_free_priv(xhci, urb_priv);
2339                         urb->hcpriv = NULL;
2340                         return ret;
2341                 }
2342         }
2343
2344         td->urb = urb;
2345         /* Add this TD to the tail of the endpoint ring's TD list */
2346         list_add_tail(&td->td_list, &ep_ring->td_list);
2347         td->start_seg = ep_ring->enq_seg;
2348         td->first_trb = ep_ring->enqueue;
2349
2350         urb_priv->td[td_index] = td;
2351
2352         return 0;
2353 }
2354
2355 static unsigned int count_sg_trbs_needed(struct xhci_hcd *xhci, struct urb *urb)
2356 {
2357         int num_sgs, num_trbs, running_total, temp, i;
2358         struct scatterlist *sg;
2359
2360         sg = NULL;
2361         num_sgs = urb->num_sgs;
2362         temp = urb->transfer_buffer_length;
2363
2364         xhci_dbg(xhci, "count sg list trbs: \n");
2365         num_trbs = 0;
2366         for_each_sg(urb->sg, sg, num_sgs, i) {
2367                 unsigned int previous_total_trbs = num_trbs;
2368                 unsigned int len = sg_dma_len(sg);
2369
2370                 /* Scatter gather list entries may cross 64KB boundaries */
2371                 running_total = TRB_MAX_BUFF_SIZE -
2372                         (sg_dma_address(sg) & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
2373                 if (running_total != 0)
2374                         num_trbs++;
2375
2376                 /* How many more 64KB chunks to transfer, how many more TRBs? */
2377                 while (running_total < sg_dma_len(sg)) {
2378                         num_trbs++;
2379                         running_total += TRB_MAX_BUFF_SIZE;
2380                 }
2381                 xhci_dbg(xhci, " sg #%d: dma = %#llx, len = %#x (%d), num_trbs = %d\n",
2382                                 i, (unsigned long long)sg_dma_address(sg),
2383                                 len, len, num_trbs - previous_total_trbs);
2384
2385                 len = min_t(int, len, temp);
2386                 temp -= len;
2387                 if (temp == 0)
2388                         break;
2389         }
2390         xhci_dbg(xhci, "\n");
2391         if (!in_interrupt())
2392                 dev_dbg(&urb->dev->dev, "ep %#x - urb len = %d, sglist used, num_trbs = %d\n",
2393                                 urb->ep->desc.bEndpointAddress,
2394                                 urb->transfer_buffer_length,
2395                                 num_trbs);
2396         return num_trbs;
2397 }
2398
2399 static void check_trb_math(struct urb *urb, int num_trbs, int running_total)
2400 {
2401         if (num_trbs != 0)
2402                 dev_dbg(&urb->dev->dev, "%s - ep %#x - Miscalculated number of "
2403                                 "TRBs, %d left\n", __func__,
2404                                 urb->ep->desc.bEndpointAddress, num_trbs);
2405         if (running_total != urb->transfer_buffer_length)
2406                 dev_dbg(&urb->dev->dev, "%s - ep %#x - Miscalculated tx length, "
2407                                 "queued %#x (%d), asked for %#x (%d)\n",
2408                                 __func__,
2409                                 urb->ep->desc.bEndpointAddress,
2410                                 running_total, running_total,
2411                                 urb->transfer_buffer_length,
2412                                 urb->transfer_buffer_length);
2413 }
2414
2415 static void giveback_first_trb(struct xhci_hcd *xhci, int slot_id,
2416                 unsigned int ep_index, unsigned int stream_id, int start_cycle,
2417                 struct xhci_generic_trb *start_trb, struct xhci_td *td)
2418 {
2419         /*
2420          * Pass all the TRBs to the hardware at once and make sure this write
2421          * isn't reordered.
2422          */
2423         wmb();
2424         start_trb->field[3] |= start_cycle;
2425         xhci_ring_ep_doorbell(xhci, slot_id, ep_index, stream_id);
2426 }
2427
2428 /*
2429  * xHCI uses normal TRBs for both bulk and interrupt.  When the interrupt
2430  * endpoint is to be serviced, the xHC will consume (at most) one TD.  A TD
2431  * (comprised of sg list entries) can take several service intervals to
2432  * transmit.
2433  */
2434 int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
2435                 struct urb *urb, int slot_id, unsigned int ep_index)
2436 {
2437         struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci,
2438                         xhci->devs[slot_id]->out_ctx, ep_index);
2439         int xhci_interval;
2440         int ep_interval;
2441
2442         xhci_interval = EP_INTERVAL_TO_UFRAMES(ep_ctx->ep_info);
2443         ep_interval = urb->interval;
2444         /* Convert to microframes */
2445         if (urb->dev->speed == USB_SPEED_LOW ||
2446                         urb->dev->speed == USB_SPEED_FULL)
2447                 ep_interval *= 8;
2448         /* FIXME change this to a warning and a suggestion to use the new API
2449          * to set the polling interval (once the API is added).
2450          */
2451         if (xhci_interval != ep_interval) {
2452                 if (!printk_ratelimit())
2453                         dev_dbg(&urb->dev->dev, "Driver uses different interval"
2454                                         " (%d microframe%s) than xHCI "
2455                                         "(%d microframe%s)\n",
2456                                         ep_interval,
2457                                         ep_interval == 1 ? "" : "s",
2458                                         xhci_interval,
2459                                         xhci_interval == 1 ? "" : "s");
2460                 urb->interval = xhci_interval;
2461                 /* Convert back to frames for LS/FS devices */
2462                 if (urb->dev->speed == USB_SPEED_LOW ||
2463                                 urb->dev->speed == USB_SPEED_FULL)
2464                         urb->interval /= 8;
2465         }
2466         return xhci_queue_bulk_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index);
2467 }
2468
2469 /*
2470  * The TD size is the number of bytes remaining in the TD (including this TRB),
2471  * right shifted by 10.
2472  * It must fit in bits 21:17, so it can't be bigger than 31.
2473  */
2474 static u32 xhci_td_remainder(unsigned int remainder)
2475 {
2476         u32 max = (1 << (21 - 17 + 1)) - 1;
2477
2478         if ((remainder >> 10) >= max)
2479                 return max << 17;
2480         else
2481                 return (remainder >> 10) << 17;
2482 }
2483
2484 static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
2485                 struct urb *urb, int slot_id, unsigned int ep_index)
2486 {
2487         struct xhci_ring *ep_ring;
2488         unsigned int num_trbs;
2489         struct urb_priv *urb_priv;
2490         struct xhci_td *td;
2491         struct scatterlist *sg;
2492         int num_sgs;
2493         int trb_buff_len, this_sg_len, running_total;
2494         bool first_trb;
2495         u64 addr;
2496         bool more_trbs_coming;
2497
2498         struct xhci_generic_trb *start_trb;
2499         int start_cycle;
2500
2501         ep_ring = xhci_urb_to_transfer_ring(xhci, urb);
2502         if (!ep_ring)
2503                 return -EINVAL;
2504
2505         num_trbs = count_sg_trbs_needed(xhci, urb);
2506         num_sgs = urb->num_sgs;
2507
2508         trb_buff_len = prepare_transfer(xhci, xhci->devs[slot_id],
2509                         ep_index, urb->stream_id,
2510                         num_trbs, urb, 0, mem_flags);
2511         if (trb_buff_len < 0)
2512                 return trb_buff_len;
2513
2514         urb_priv = urb->hcpriv;
2515         td = urb_priv->td[0];
2516
2517         /*
2518          * Don't give the first TRB to the hardware (by toggling the cycle bit)
2519          * until we've finished creating all the other TRBs.  The ring's cycle
2520          * state may change as we enqueue the other TRBs, so save it too.
2521          */
2522         start_trb = &ep_ring->enqueue->generic;
2523         start_cycle = ep_ring->cycle_state;
2524
2525         running_total = 0;
2526         /*
2527          * How much data is in the first TRB?
2528          *
2529          * There are three forces at work for TRB buffer pointers and lengths:
2530          * 1. We don't want to walk off the end of this sg-list entry buffer.
2531          * 2. The transfer length that the driver requested may be smaller than
2532          *    the amount of memory allocated for this scatter-gather list.
2533          * 3. TRBs buffers can't cross 64KB boundaries.
2534          */
2535         sg = urb->sg;
2536         addr = (u64) sg_dma_address(sg);
2537         this_sg_len = sg_dma_len(sg);
2538         trb_buff_len = TRB_MAX_BUFF_SIZE -
2539                 (addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
2540         trb_buff_len = min_t(int, trb_buff_len, this_sg_len);
2541         if (trb_buff_len > urb->transfer_buffer_length)
2542                 trb_buff_len = urb->transfer_buffer_length;
2543         xhci_dbg(xhci, "First length to xfer from 1st sglist entry = %u\n",
2544                         trb_buff_len);
2545
2546         first_trb = true;
2547         /* Queue the first TRB, even if it's zero-length */
2548         do {
2549                 u32 field = 0;
2550                 u32 length_field = 0;
2551                 u32 remainder = 0;
2552
2553                 /* Don't change the cycle bit of the first TRB until later */
2554                 if (first_trb)
2555                         first_trb = false;
2556                 else
2557                         field |= ep_ring->cycle_state;
2558
2559                 /* Chain all the TRBs together; clear the chain bit in the last
2560                  * TRB to indicate it's the last TRB in the chain.
2561                  */
2562                 if (num_trbs > 1) {
2563                         field |= TRB_CHAIN;
2564                 } else {
2565                         /* FIXME - add check for ZERO_PACKET flag before this */
2566                         td->last_trb = ep_ring->enqueue;
2567                         field |= TRB_IOC;
2568                 }
2569                 xhci_dbg(xhci, " sg entry: dma = %#x, len = %#x (%d), "
2570                                 "64KB boundary at %#x, end dma = %#x\n",
2571                                 (unsigned int) addr, trb_buff_len, trb_buff_len,
2572                                 (unsigned int) (addr + TRB_MAX_BUFF_SIZE) & ~(TRB_MAX_BUFF_SIZE - 1),
2573                                 (unsigned int) addr + trb_buff_len);
2574                 if (TRB_MAX_BUFF_SIZE -
2575                                 (addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1)) < trb_buff_len) {
2576                         xhci_warn(xhci, "WARN: sg dma xfer crosses 64KB boundaries!\n");
2577                         xhci_dbg(xhci, "Next boundary at %#x, end dma = %#x\n",
2578                                         (unsigned int) (addr + TRB_MAX_BUFF_SIZE) & ~(TRB_MAX_BUFF_SIZE - 1),
2579                                         (unsigned int) addr + trb_buff_len);
2580                 }
2581                 remainder = xhci_td_remainder(urb->transfer_buffer_length -
2582                                 running_total) ;
2583                 length_field = TRB_LEN(trb_buff_len) |
2584                         remainder |
2585                         TRB_INTR_TARGET(0);
2586                 if (num_trbs > 1)
2587                         more_trbs_coming = true;
2588                 else
2589                         more_trbs_coming = false;
2590                 queue_trb(xhci, ep_ring, false, more_trbs_coming,
2591                                 lower_32_bits(addr),
2592                                 upper_32_bits(addr),
2593                                 length_field,
2594                                 /* We always want to know if the TRB was short,
2595                                  * or we won't get an event when it completes.
2596                                  * (Unless we use event data TRBs, which are a
2597                                  * waste of space and HC resources.)
2598                                  */
2599                                 field | TRB_ISP | TRB_TYPE(TRB_NORMAL));
2600                 --num_trbs;
2601                 running_total += trb_buff_len;
2602
2603                 /* Calculate length for next transfer --
2604                  * Are we done queueing all the TRBs for this sg entry?
2605                  */
2606                 this_sg_len -= trb_buff_len;
2607                 if (this_sg_len == 0) {
2608                         --num_sgs;
2609                         if (num_sgs == 0)
2610                                 break;
2611                         sg = sg_next(sg);
2612                         addr = (u64) sg_dma_address(sg);
2613                         this_sg_len = sg_dma_len(sg);
2614                 } else {
2615                         addr += trb_buff_len;
2616                 }
2617
2618                 trb_buff_len = TRB_MAX_BUFF_SIZE -
2619                         (addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
2620                 trb_buff_len = min_t(int, trb_buff_len, this_sg_len);
2621                 if (running_total + trb_buff_len > urb->transfer_buffer_length)
2622                         trb_buff_len =
2623                                 urb->transfer_buffer_length - running_total;
2624         } while (running_total < urb->transfer_buffer_length);
2625
2626         check_trb_math(urb, num_trbs, running_total);
2627         giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id,
2628                         start_cycle, start_trb, td);
2629         return 0;
2630 }
2631
2632 /* This is very similar to what ehci-q.c qtd_fill() does */
2633 int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
2634                 struct urb *urb, int slot_id, unsigned int ep_index)
2635 {
2636         struct xhci_ring *ep_ring;
2637         struct urb_priv *urb_priv;
2638         struct xhci_td *td;
2639         int num_trbs;
2640         struct xhci_generic_trb *start_trb;
2641         bool first_trb;
2642         bool more_trbs_coming;
2643         int start_cycle;
2644         u32 field, length_field;
2645
2646         int running_total, trb_buff_len, ret;
2647         u64 addr;
2648
2649         if (urb->num_sgs)
2650                 return queue_bulk_sg_tx(xhci, mem_flags, urb, slot_id, ep_index);
2651
2652         ep_ring = xhci_urb_to_transfer_ring(xhci, urb);
2653         if (!ep_ring)
2654                 return -EINVAL;
2655
2656         num_trbs = 0;
2657         /* How much data is (potentially) left before the 64KB boundary? */
2658         running_total = TRB_MAX_BUFF_SIZE -
2659                 (urb->transfer_dma & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
2660
2661         /* If there's some data on this 64KB chunk, or we have to send a
2662          * zero-length transfer, we need at least one TRB
2663          */
2664         if (running_total != 0 || urb->transfer_buffer_length == 0)
2665                 num_trbs++;
2666         /* How many more 64KB chunks to transfer, how many more TRBs? */
2667         while (running_total < urb->transfer_buffer_length) {
2668                 num_trbs++;
2669                 running_total += TRB_MAX_BUFF_SIZE;
2670         }
2671         /* FIXME: this doesn't deal with URB_ZERO_PACKET - need one more */
2672
2673         if (!in_interrupt())
2674                 dev_dbg(&urb->dev->dev, "ep %#x - urb len = %#x (%d), addr = %#llx, num_trbs = %d\n",
2675                                 urb->ep->desc.bEndpointAddress,
2676                                 urb->transfer_buffer_length,
2677                                 urb->transfer_buffer_length,
2678                                 (unsigned long long)urb->transfer_dma,
2679                                 num_trbs);
2680
2681         ret = prepare_transfer(xhci, xhci->devs[slot_id],
2682                         ep_index, urb->stream_id,
2683                         num_trbs, urb, 0, mem_flags);
2684         if (ret < 0)
2685                 return ret;
2686
2687         urb_priv = urb->hcpriv;
2688         td = urb_priv->td[0];
2689
2690         /*
2691          * Don't give the first TRB to the hardware (by toggling the cycle bit)
2692          * until we've finished creating all the other TRBs.  The ring's cycle
2693          * state may change as we enqueue the other TRBs, so save it too.
2694          */
2695         start_trb = &ep_ring->enqueue->generic;
2696         start_cycle = ep_ring->cycle_state;
2697
2698         running_total = 0;
2699         /* How much data is in the first TRB? */
2700         addr = (u64) urb->transfer_dma;
2701         trb_buff_len = TRB_MAX_BUFF_SIZE -
2702                 (urb->transfer_dma & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
2703         if (urb->transfer_buffer_length < trb_buff_len)
2704                 trb_buff_len = urb->transfer_buffer_length;
2705
2706         first_trb = true;
2707
2708         /* Queue the first TRB, even if it's zero-length */
2709         do {
2710                 u32 remainder = 0;
2711                 field = 0;
2712
2713                 /* Don't change the cycle bit of the first TRB until later */
2714                 if (first_trb)
2715                         first_trb = false;
2716                 else
2717                         field |= ep_ring->cycle_state;
2718
2719                 /* Chain all the TRBs together; clear the chain bit in the last
2720                  * TRB to indicate it's the last TRB in the chain.
2721                  */
2722                 if (num_trbs > 1) {
2723                         field |= TRB_CHAIN;
2724                 } else {
2725                         /* FIXME - add check for ZERO_PACKET flag before this */
2726                         td->last_trb = ep_ring->enqueue;
2727                         field |= TRB_IOC;
2728                 }
2729                 remainder = xhci_td_remainder(urb->transfer_buffer_length -
2730                                 running_total);
2731                 length_field = TRB_LEN(trb_buff_len) |
2732                         remainder |
2733                         TRB_INTR_TARGET(0);
2734                 if (num_trbs > 1)
2735                         more_trbs_coming = true;
2736                 else
2737                         more_trbs_coming = false;
2738                 queue_trb(xhci, ep_ring, false, more_trbs_coming,
2739                                 lower_32_bits(addr),
2740                                 upper_32_bits(addr),
2741                                 length_field,
2742                                 /* We always want to know if the TRB was short,
2743                                  * or we won't get an event when it completes.
2744                                  * (Unless we use event data TRBs, which are a
2745                                  * waste of space and HC resources.)
2746                                  */
2747                                 field | TRB_ISP | TRB_TYPE(TRB_NORMAL));
2748                 --num_trbs;
2749                 running_total += trb_buff_len;
2750
2751                 /* Calculate length for next transfer */
2752                 addr += trb_buff_len;
2753                 trb_buff_len = urb->transfer_buffer_length - running_total;
2754                 if (trb_buff_len > TRB_MAX_BUFF_SIZE)
2755                         trb_buff_len = TRB_MAX_BUFF_SIZE;
2756         } while (running_total < urb->transfer_buffer_length);
2757
2758         check_trb_math(urb, num_trbs, running_total);
2759         giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id,
2760                         start_cycle, start_trb, td);
2761         return 0;
2762 }
2763
2764 /* Caller must have locked xhci->lock */
2765 int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
2766                 struct urb *urb, int slot_id, unsigned int ep_index)
2767 {
2768         struct xhci_ring *ep_ring;
2769         int num_trbs;
2770         int ret;
2771         struct usb_ctrlrequest *setup;
2772         struct xhci_generic_trb *start_trb;
2773         int start_cycle;
2774         u32 field, length_field;
2775         struct urb_priv *urb_priv;
2776         struct xhci_td *td;
2777
2778         ep_ring = xhci_urb_to_transfer_ring(xhci, urb);
2779         if (!ep_ring)
2780                 return -EINVAL;
2781
2782         /*
2783          * Need to copy setup packet into setup TRB, so we can't use the setup
2784          * DMA address.
2785          */
2786         if (!urb->setup_packet)
2787                 return -EINVAL;
2788
2789         if (!in_interrupt())
2790                 xhci_dbg(xhci, "Queueing ctrl tx for slot id %d, ep %d\n",
2791                                 slot_id, ep_index);
2792         /* 1 TRB for setup, 1 for status */
2793         num_trbs = 2;
2794         /*
2795          * Don't need to check if we need additional event data and normal TRBs,
2796          * since data in control transfers will never get bigger than 16MB
2797          * XXX: can we get a buffer that crosses 64KB boundaries?
2798          */
2799         if (urb->transfer_buffer_length > 0)
2800                 num_trbs++;
2801         ret = prepare_transfer(xhci, xhci->devs[slot_id],
2802                         ep_index, urb->stream_id,
2803                         num_trbs, urb, 0, mem_flags);
2804         if (ret < 0)
2805                 return ret;
2806
2807         urb_priv = urb->hcpriv;
2808         td = urb_priv->td[0];
2809
2810         /*
2811          * Don't give the first TRB to the hardware (by toggling the cycle bit)
2812          * until we've finished creating all the other TRBs.  The ring's cycle
2813          * state may change as we enqueue the other TRBs, so save it too.
2814          */
2815         start_trb = &ep_ring->enqueue->generic;
2816         start_cycle = ep_ring->cycle_state;
2817
2818         /* Queue setup TRB - see section 6.4.1.2.1 */
2819         /* FIXME better way to translate setup_packet into two u32 fields? */
2820         setup = (struct usb_ctrlrequest *) urb->setup_packet;
2821         queue_trb(xhci, ep_ring, false, true,
2822                         /* FIXME endianness is probably going to bite my ass here. */
2823                         setup->bRequestType | setup->bRequest << 8 | setup->wValue << 16,
2824                         setup->wIndex | setup->wLength << 16,
2825                         TRB_LEN(8) | TRB_INTR_TARGET(0),
2826                         /* Immediate data in pointer */
2827                         TRB_IDT | TRB_TYPE(TRB_SETUP));
2828
2829         /* If there's data, queue data TRBs */
2830         field = 0;
2831         length_field = TRB_LEN(urb->transfer_buffer_length) |
2832                 xhci_td_remainder(urb->transfer_buffer_length) |
2833                 TRB_INTR_TARGET(0);
2834         if (urb->transfer_buffer_length > 0) {
2835                 if (setup->bRequestType & USB_DIR_IN)
2836                         field |= TRB_DIR_IN;
2837                 queue_trb(xhci, ep_ring, false, true,
2838                                 lower_32_bits(urb->transfer_dma),
2839                                 upper_32_bits(urb->transfer_dma),
2840                                 length_field,
2841                                 /* Event on short tx */
2842                                 field | TRB_ISP | TRB_TYPE(TRB_DATA) | ep_ring->cycle_state);
2843         }
2844
2845         /* Save the DMA address of the last TRB in the TD */
2846         td->last_trb = ep_ring->enqueue;
2847
2848         /* Queue status TRB - see Table 7 and sections 4.11.2.2 and 6.4.1.2.3 */
2849         /* If the device sent data, the status stage is an OUT transfer */
2850         if (urb->transfer_buffer_length > 0 && setup->bRequestType & USB_DIR_IN)
2851                 field = 0;
2852         else
2853                 field = TRB_DIR_IN;
2854         queue_trb(xhci, ep_ring, false, false,
2855                         0,
2856                         0,
2857                         TRB_INTR_TARGET(0),
2858                         /* Event on completion */
2859                         field | TRB_IOC | TRB_TYPE(TRB_STATUS) | ep_ring->cycle_state);
2860
2861         giveback_first_trb(xhci, slot_id, ep_index, 0,
2862                         start_cycle, start_trb, td);
2863         return 0;
2864 }
2865
2866 static int count_isoc_trbs_needed(struct xhci_hcd *xhci,
2867                 struct urb *urb, int i)
2868 {
2869         int num_trbs = 0;
2870         u64 addr, td_len, running_total;
2871
2872         addr = (u64) (urb->transfer_dma + urb->iso_frame_desc[i].offset);
2873         td_len = urb->iso_frame_desc[i].length;
2874
2875         running_total = TRB_MAX_BUFF_SIZE -
2876                         (addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
2877         if (running_total != 0)
2878                 num_trbs++;
2879
2880         while (running_total < td_len) {
2881                 num_trbs++;
2882                 running_total += TRB_MAX_BUFF_SIZE;
2883         }
2884
2885         return num_trbs;
2886 }
2887
2888 /* This is for isoc transfer */
2889 static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
2890                 struct urb *urb, int slot_id, unsigned int ep_index)
2891 {
2892         struct xhci_ring *ep_ring;
2893         struct urb_priv *urb_priv;
2894         struct xhci_td *td;
2895         int num_tds, trbs_per_td;
2896         struct xhci_generic_trb *start_trb;
2897         bool first_trb;
2898         int start_cycle;
2899         u32 field, length_field;
2900         int running_total, trb_buff_len, td_len, td_remain_len, ret;
2901         u64 start_addr, addr;
2902         int i, j;
2903
2904         ep_ring = xhci->devs[slot_id]->eps[ep_index].ring;
2905
2906         num_tds = urb->number_of_packets;
2907         if (num_tds < 1) {
2908                 xhci_dbg(xhci, "Isoc URB with zero packets?\n");
2909                 return -EINVAL;
2910         }
2911
2912         if (!in_interrupt())
2913                 dev_dbg(&urb->dev->dev, "ep %#x - urb len = %#x (%d),"
2914                                 " addr = %#llx, num_tds = %d\n",
2915                                 urb->ep->desc.bEndpointAddress,
2916                                 urb->transfer_buffer_length,
2917                                 urb->transfer_buffer_length,
2918                                 (unsigned long long)urb->transfer_dma,
2919                                 num_tds);
2920
2921         start_addr = (u64) urb->transfer_dma;
2922         start_trb = &ep_ring->enqueue->generic;
2923         start_cycle = ep_ring->cycle_state;
2924
2925         /* Queue the first TRB, even if it's zero-length */
2926         for (i = 0; i < num_tds; i++) {
2927                 first_trb = true;
2928
2929                 running_total = 0;
2930                 addr = start_addr + urb->iso_frame_desc[i].offset;
2931                 td_len = urb->iso_frame_desc[i].length;
2932                 td_remain_len = td_len;
2933
2934                 trbs_per_td = count_isoc_trbs_needed(xhci, urb, i);
2935
2936                 ret = prepare_transfer(xhci, xhci->devs[slot_id], ep_index,
2937                                 urb->stream_id, trbs_per_td, urb, i, mem_flags);
2938                 if (ret < 0)
2939                         return ret;
2940
2941                 urb_priv = urb->hcpriv;
2942                 td = urb_priv->td[i];
2943
2944                 for (j = 0; j < trbs_per_td; j++) {
2945                         u32 remainder = 0;
2946                         field = 0;
2947
2948                         if (first_trb) {
2949                                 /* Queue the isoc TRB */
2950                                 field |= TRB_TYPE(TRB_ISOC);
2951                                 /* Assume URB_ISO_ASAP is set */
2952                                 field |= TRB_SIA;
2953                                 if (i > 0)
2954                                         field |= ep_ring->cycle_state;
2955                                 first_trb = false;
2956                         } else {
2957                                 /* Queue other normal TRBs */
2958                                 field |= TRB_TYPE(TRB_NORMAL);
2959                                 field |= ep_ring->cycle_state;
2960                         }
2961
2962                         /* Chain all the TRBs together; clear the chain bit in
2963                          * the last TRB to indicate it's the last TRB in the
2964                          * chain.
2965                          */
2966                         if (j < trbs_per_td - 1) {
2967                                 field |= TRB_CHAIN;
2968                         } else {
2969                                 td->last_trb = ep_ring->enqueue;
2970                                 field |= TRB_IOC;
2971                         }
2972
2973                         /* Calculate TRB length */
2974                         trb_buff_len = TRB_MAX_BUFF_SIZE -
2975                                 (addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
2976                         if (trb_buff_len > td_remain_len)
2977                                 trb_buff_len = td_remain_len;
2978
2979                         remainder = xhci_td_remainder(td_len - running_total);
2980                         length_field = TRB_LEN(trb_buff_len) |
2981                                 remainder |
2982                                 TRB_INTR_TARGET(0);
2983                         queue_trb(xhci, ep_ring, false, false,
2984                                 lower_32_bits(addr),
2985                                 upper_32_bits(addr),
2986                                 length_field,
2987                                 /* We always want to know if the TRB was short,
2988                                  * or we won't get an event when it completes.
2989                                  * (Unless we use event data TRBs, which are a
2990                                  * waste of space and HC resources.)
2991                                  */
2992                                 field | TRB_ISP);
2993                         running_total += trb_buff_len;
2994
2995                         addr += trb_buff_len;
2996                         td_remain_len -= trb_buff_len;
2997                 }
2998
2999                 /* Check TD length */
3000                 if (running_total != td_len) {
3001                         xhci_err(xhci, "ISOC TD length unmatch\n");
3002                         return -EINVAL;
3003                 }
3004         }
3005
3006         wmb();
3007         start_trb->field[3] |= start_cycle;
3008
3009         xhci_ring_ep_doorbell(xhci, slot_id, ep_index, urb->stream_id);
3010         return 0;
3011 }
3012
3013 /*
3014  * Check transfer ring to guarantee there is enough room for the urb.
3015  * Update ISO URB start_frame and interval.
3016  * Update interval as xhci_queue_intr_tx does. Just use xhci frame_index to
3017  * update the urb->start_frame by now.
3018  * Always assume URB_ISO_ASAP set, and NEVER use urb->start_frame as input.
3019  */
3020 int xhci_queue_isoc_tx_prepare(struct xhci_hcd *xhci, gfp_t mem_flags,
3021                 struct urb *urb, int slot_id, unsigned int ep_index)
3022 {
3023         struct xhci_virt_device *xdev;
3024         struct xhci_ring *ep_ring;
3025         struct xhci_ep_ctx *ep_ctx;
3026         int start_frame;
3027         int xhci_interval;
3028         int ep_interval;
3029         int num_tds, num_trbs, i;
3030         int ret;
3031
3032         xdev = xhci->devs[slot_id];
3033         ep_ring = xdev->eps[ep_index].ring;
3034         ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
3035
3036         num_trbs = 0;
3037         num_tds = urb->number_of_packets;
3038         for (i = 0; i < num_tds; i++)
3039                 num_trbs += count_isoc_trbs_needed(xhci, urb, i);
3040
3041         /* Check the ring to guarantee there is enough room for the whole urb.
3042          * Do not insert any td of the urb to the ring if the check failed.
3043          */
3044         ret = prepare_ring(xhci, ep_ring, ep_ctx->ep_info & EP_STATE_MASK,
3045                                 num_trbs, mem_flags);
3046         if (ret)
3047                 return ret;
3048
3049         start_frame = xhci_readl(xhci, &xhci->run_regs->microframe_index);
3050         start_frame &= 0x3fff;
3051
3052         urb->start_frame = start_frame;
3053         if (urb->dev->speed == USB_SPEED_LOW ||
3054                         urb->dev->speed == USB_SPEED_FULL)
3055                 urb->start_frame >>= 3;
3056
3057         xhci_interval = EP_INTERVAL_TO_UFRAMES(ep_ctx->ep_info);
3058         ep_interval = urb->interval;
3059         /* Convert to microframes */
3060         if (urb->dev->speed == USB_SPEED_LOW ||
3061                         urb->dev->speed == USB_SPEED_FULL)
3062                 ep_interval *= 8;
3063         /* FIXME change this to a warning and a suggestion to use the new API
3064          * to set the polling interval (once the API is added).
3065          */
3066         if (xhci_interval != ep_interval) {
3067                 if (!printk_ratelimit())
3068                         dev_dbg(&urb->dev->dev, "Driver uses different interval"
3069                                         " (%d microframe%s) than xHCI "
3070                                         "(%d microframe%s)\n",
3071                                         ep_interval,
3072                                         ep_interval == 1 ? "" : "s",
3073                                         xhci_interval,
3074                                         xhci_interval == 1 ? "" : "s");
3075                 urb->interval = xhci_interval;
3076                 /* Convert back to frames for LS/FS devices */
3077                 if (urb->dev->speed == USB_SPEED_LOW ||
3078                                 urb->dev->speed == USB_SPEED_FULL)
3079                         urb->interval /= 8;
3080         }
3081         return xhci_queue_isoc_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index);
3082 }
3083
3084 /****           Command Ring Operations         ****/
3085
3086 /* Generic function for queueing a command TRB on the command ring.
3087  * Check to make sure there's room on the command ring for one command TRB.
3088  * Also check that there's room reserved for commands that must not fail.
3089  * If this is a command that must not fail, meaning command_must_succeed = TRUE,
3090  * then only check for the number of reserved spots.
3091  * Don't decrement xhci->cmd_ring_reserved_trbs after we've queued the TRB
3092  * because the command event handler may want to resubmit a failed command.
3093  */
3094 static int queue_command(struct xhci_hcd *xhci, u32 field1, u32 field2,
3095                 u32 field3, u32 field4, bool command_must_succeed)
3096 {
3097         int reserved_trbs = xhci->cmd_ring_reserved_trbs;
3098         int ret;
3099
3100         if (!command_must_succeed)
3101                 reserved_trbs++;
3102
3103         ret = prepare_ring(xhci, xhci->cmd_ring, EP_STATE_RUNNING,
3104                         reserved_trbs, GFP_ATOMIC);
3105         if (ret < 0) {
3106                 xhci_err(xhci, "ERR: No room for command on command ring\n");
3107                 if (command_must_succeed)
3108                         xhci_err(xhci, "ERR: Reserved TRB counting for "
3109                                         "unfailable commands failed.\n");
3110                 return ret;
3111         }
3112         queue_trb(xhci, xhci->cmd_ring, false, false, field1, field2, field3,
3113                         field4 | xhci->cmd_ring->cycle_state);
3114         return 0;
3115 }
3116
3117 /* Queue a no-op command on the command ring */
3118 static int queue_cmd_noop(struct xhci_hcd *xhci)
3119 {
3120         return queue_command(xhci, 0, 0, 0, TRB_TYPE(TRB_CMD_NOOP), false);
3121 }
3122
3123 /*
3124  * Place a no-op command on the command ring to test the command and
3125  * event ring.
3126  */
3127 void *xhci_setup_one_noop(struct xhci_hcd *xhci)
3128 {
3129         if (queue_cmd_noop(xhci) < 0)
3130                 return NULL;
3131         xhci->noops_submitted++;
3132         return xhci_ring_cmd_db;
3133 }
3134
3135 /* Queue a slot enable or disable request on the command ring */
3136 int xhci_queue_slot_control(struct xhci_hcd *xhci, u32 trb_type, u32 slot_id)
3137 {
3138         return queue_command(xhci, 0, 0, 0,
3139                         TRB_TYPE(trb_type) | SLOT_ID_FOR_TRB(slot_id), false);
3140 }
3141
3142 /* Queue an address device command TRB */
3143 int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
3144                 u32 slot_id)
3145 {
3146         return queue_command(xhci, lower_32_bits(in_ctx_ptr),
3147                         upper_32_bits(in_ctx_ptr), 0,
3148                         TRB_TYPE(TRB_ADDR_DEV) | SLOT_ID_FOR_TRB(slot_id),
3149                         false);
3150 }
3151
3152 int xhci_queue_vendor_command(struct xhci_hcd *xhci,
3153                 u32 field1, u32 field2, u32 field3, u32 field4)
3154 {
3155         return queue_command(xhci, field1, field2, field3, field4, false);
3156 }
3157
3158 /* Queue a reset device command TRB */
3159 int xhci_queue_reset_device(struct xhci_hcd *xhci, u32 slot_id)
3160 {
3161         return queue_command(xhci, 0, 0, 0,
3162                         TRB_TYPE(TRB_RESET_DEV) | SLOT_ID_FOR_TRB(slot_id),
3163                         false);
3164 }
3165
3166 /* Queue a configure endpoint command TRB */
3167 int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
3168                 u32 slot_id, bool command_must_succeed)
3169 {
3170         return queue_command(xhci, lower_32_bits(in_ctx_ptr),
3171                         upper_32_bits(in_ctx_ptr), 0,
3172                         TRB_TYPE(TRB_CONFIG_EP) | SLOT_ID_FOR_TRB(slot_id),
3173                         command_must_succeed);
3174 }
3175
3176 /* Queue an evaluate context command TRB */
3177 int xhci_queue_evaluate_context(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
3178                 u32 slot_id)
3179 {
3180         return queue_command(xhci, lower_32_bits(in_ctx_ptr),
3181                         upper_32_bits(in_ctx_ptr), 0,
3182                         TRB_TYPE(TRB_EVAL_CONTEXT) | SLOT_ID_FOR_TRB(slot_id),
3183                         false);
3184 }
3185
3186 /*
3187  * Suspend is set to indicate "Stop Endpoint Command" is being issued to stop
3188  * activity on an endpoint that is about to be suspended.
3189  */
3190 int xhci_queue_stop_endpoint(struct xhci_hcd *xhci, int slot_id,
3191                 unsigned int ep_index, int suspend)
3192 {
3193         u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id);
3194         u32 trb_ep_index = EP_ID_FOR_TRB(ep_index);
3195         u32 type = TRB_TYPE(TRB_STOP_RING);
3196         u32 trb_suspend = SUSPEND_PORT_FOR_TRB(suspend);
3197
3198         return queue_command(xhci, 0, 0, 0,
3199                         trb_slot_id | trb_ep_index | type | trb_suspend, false);
3200 }
3201
3202 /* Set Transfer Ring Dequeue Pointer command.
3203  * This should not be used for endpoints that have streams enabled.
3204  */
3205 static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id,
3206                 unsigned int ep_index, unsigned int stream_id,
3207                 struct xhci_segment *deq_seg,
3208                 union xhci_trb *deq_ptr, u32 cycle_state)
3209 {
3210         dma_addr_t addr;
3211         u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id);
3212         u32 trb_ep_index = EP_ID_FOR_TRB(ep_index);
3213         u32 trb_stream_id = STREAM_ID_FOR_TRB(stream_id);
3214         u32 type = TRB_TYPE(TRB_SET_DEQ);
3215
3216         addr = xhci_trb_virt_to_dma(deq_seg, deq_ptr);
3217         if (addr == 0) {
3218                 xhci_warn(xhci, "WARN Cannot submit Set TR Deq Ptr\n");
3219                 xhci_warn(xhci, "WARN deq seg = %p, deq pt = %p\n",
3220                                 deq_seg, deq_ptr);
3221                 return 0;
3222         }
3223         return queue_command(xhci, lower_32_bits(addr) | cycle_state,
3224                         upper_32_bits(addr), trb_stream_id,
3225                         trb_slot_id | trb_ep_index | type, false);
3226 }
3227
3228 int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id,
3229                 unsigned int ep_index)
3230 {
3231         u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id);
3232         u32 trb_ep_index = EP_ID_FOR_TRB(ep_index);
3233         u32 type = TRB_TYPE(TRB_RESET_EP);
3234
3235         return queue_command(xhci, 0, 0, 0, trb_slot_id | trb_ep_index | type,
3236                         false);
3237 }