6 years agoDrivers: hv: Notify the host of permanent hot-add failures
K. Y. Srinivasan [Mon, 18 Mar 2013 20:51:38 +0000]
Drivers: hv: Notify the host of permanent hot-add failures

If memory hot-add fails with the error -EEXIST, then this is a permanent
failure. Notify the host of this information, so the host will not attempt
hot-add again. If the failure were a transient failure, host will attempt
a hot-add after some delay.

In this version of the patch, I have added some additional comments
to clarify how the host treats different failure conditions.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoDrivers: hv: balloon: Support 2M page allocations for ballooning
K. Y. Srinivasan [Mon, 18 Mar 2013 20:51:37 +0000]
Drivers: hv: balloon: Support 2M page allocations for ballooning

On Hyper-V it will be very efficient to use 2M allocations in the guest as this
makes the ballooning protocol with the host that much more efficient. Hyper-V
uses page ranges (start pfn : number of pages) to specify memory being moved
around and with 2M pages this encoding can be very efficient. However, when
memory is returned to the guest, the host does not guarantee any granularity.
To deal with this issue, split the page soon after a successful 2M allocation
so that this memory can potentially be freed as 4K pages.

If 2M allocations fail, we revert to 4K allocations.

In this version of the patch, based on the feedback from Michal Hocko
<mhocko@suse.cz>, I have added some additional commentary to the patch
description.

Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomm: export split_page()
K. Y. Srinivasan [Mon, 25 Mar 2013 22:47:38 +0000]
mm: export split_page()

This symbol will be used in the Hyper-V balloon driver to support 2M
allocations.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoDrivers: hv: balloon: Permit Linux to specify hot-add alignment requirements
K. Y. Srinivasan [Fri, 29 Mar 2013 14:36:11 +0000]
Drivers: hv: balloon: Permit Linux to specify hot-add alignment requirements

Some Windows hosts permit the guest to specify memory hot-add alignment
requirements (if any). Linux currently requires a 128MB alignment on memory
segments that can be hot-added. Specify this alignment requirement to the
host.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomisc: apds990x: add CONFIG_PM_SLEEP to suspend/resume functions
Jingoo Han [Tue, 26 Mar 2013 07:05:58 +0000]
misc: apds990x: add CONFIG_PM_SLEEP to suspend/resume functions

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.

drivers/misc/apds990x.c:1205:12: warning: 'apds990x_suspend' defined but not used [-Wunused-function]
drivers/misc/apds990x.c:1214:12: warning: 'apds990x_resume' defined but not used [-Wunused-function]

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomisc: bh1770glc: add CONFIG_PM_SLEEP to suspend/resume functions
Jingoo Han [Tue, 26 Mar 2013 07:05:36 +0000]
misc: bh1770glc: add CONFIG_PM_SLEEP to suspend/resume functions

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.

drivers/misc/bh1770glc.c:1314:12: warning: 'bh1770_suspend' defined but not used [-Wunused-function]
drivers/misc/bh1770glc.c:1324:12: warning: 'bh1770_resume' defined but not used [-Wunused-function]

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomisc: bh1780gli: add CONFIG_PM_SLEEP to suspend/resume functions
Jingoo Han [Tue, 26 Mar 2013 07:05:06 +0000]
misc: bh1780gli: add CONFIG_PM_SLEEP to suspend/resume functions

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.

drivers/misc/bh1780gli.c:200:12: warning: 'bh1780_suspend' defined but not used [-Wunused-function]
drivers/misc/bh1780gli.c:222:12: warning: 'bh1780_resume' defined but not used [-Wunused-function]

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: bus: Implement bus driver data setter/getter
Samuel Ortiz [Wed, 27 Mar 2013 15:29:59 +0000]
mei: bus: Implement bus driver data setter/getter

MEI drivers should be able to carry their private data around.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: bus: Synchronous API for the data transmission
Samuel Ortiz [Wed, 27 Mar 2013 15:29:58 +0000]
mei: bus: Synchronous API for the data transmission

Define a truly synchronous API for the bus Tx path by putting all pending
request to the write list and wait for the interrupt tx handler to wake
us up.
The ___mei_cl_send() out path is also slightly reworked to make it look more
like main.c:mei_write().

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: bus: Call bus routines from the core code
Samuel Ortiz [Wed, 27 Mar 2013 15:29:57 +0000]
mei: bus: Call bus routines from the core code

Register the MEI bus type against the kernel core bus APIs and
call the bus Rx handler from interrupt.c

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: bus: Add bus related structures to mei_cl
Samuel Ortiz [Wed, 27 Mar 2013 15:29:56 +0000]
mei: bus: Add bus related structures to mei_cl

We keep track of all MEI devices on the bus through a specific linked list.
We also have a mei_device instance in the mei_cl structure.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: bus: Initial implementation for I/O routines
Samuel Ortiz [Wed, 27 Mar 2013 15:29:55 +0000]
mei: bus: Initial implementation for I/O routines

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: bus: Implement driver registration
Samuel Ortiz [Wed, 27 Mar 2013 15:29:54 +0000]
mei: bus: Implement driver registration

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: bus: Initial MEI Client bus type implementation
Samuel Ortiz [Wed, 27 Mar 2013 15:29:53 +0000]
mei: bus: Initial MEI Client bus type implementation

mei client bus will present some of the mei clients
as devices for other standard subsystems

Implement the probe, remove, match, device addtion routines, along with
the sysfs and uevent ones. mei_cl_device_id is also added to
mod_devicetable.h
A mei-cleint-bus.txt document describing the rationale and the API usage
is also added while ABI/testing/sysfs-bus-mei describeis the modalias ABI.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: move mei-me to separate module
Tomas Winkler [Wed, 27 Mar 2013 14:58:30 +0000]
mei: move mei-me to separate module

mei layer provides host bus message layer, client management,
and os interface

mei-me - provides access to ME hardware through
the pci bus

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: prefix me hardware specific functions with mei_me_
Tomas Winkler [Wed, 27 Mar 2013 14:58:29 +0000]
mei: prefix me hardware specific functions with mei_me_

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: rename function mei_hw_init to mei_start
Tomas Winkler [Wed, 27 Mar 2013 14:58:28 +0000]
mei: rename function mei_hw_init to mei_start

The hw initialization is now done as part of
hw specific code this makes the name mei_hw_init little misleading.

We rename it to mei_start in spirit of already existing
functions mei_stop and mei_reset.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: ME structures should be initialized in mei_device_init
Tomas Winkler [Wed, 27 Mar 2013 14:58:27 +0000]
mei: ME structures should be initialized in mei_device_init

mei_timer and mei_host_client_init belongs to mei framework
and are not ME hw specific.
AMTHIF and WD are available only for ME but are above the hardware layer
so move the initialization back from mei_me_dev_init to mei_device_init.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: unregister watchdog from mei_stop function
Tomas Winkler [Wed, 27 Mar 2013 14:58:26 +0000]
mei: unregister watchdog from mei_stop function

we need to unregister watchdog device both in suspend and remove
as the registration is recreated on reset

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: drop RECOVERING_FROM_RESET device state
Tomas Winkler [Wed, 27 Mar 2013 11:42:15 +0000]
mei: drop RECOVERING_FROM_RESET device state

ECOVERING_FROM_RESET device state is never set
we can remove it

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoMerge branch 'char-misc-linus' into char-misc-next
Greg Kroah-Hartman [Tue, 26 Mar 2013 23:09:30 +0000]
Merge branch 'char-misc-linus' into char-misc-next

This picks up the MEI fixes that we need in this branch now.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomfd: pm8921: Disable driver until it gets fixed
David Brown [Tue, 26 Mar 2013 18:20:17 +0000]
mfd: pm8921: Disable driver until it gets fixed

The pm8921 driver has been broken for a while now, but was prevented
from compiling because the SSBI bus driver was missing.  Now that SSBI
is present, pm8921 causes compile fails.

Until the pm8921 driver is fixed, mark it as BROKEN to prevent
compiles from failing.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoMerge tag 'arizona-extcon-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git...
Greg Kroah-Hartman [Tue, 26 Mar 2013 16:19:02 +0000]
Merge tag 'arizona-extcon-asoc' of git://git./linux/kernel/git/broonie/misc into char-misc-next

Mark writes:

ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs

This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active.  The first
patch is a refactoring to make the extcon side easier.

6 years agoextcon: arizona: Fix interaction between headphone outputs and identification
Mark Brown [Fri, 22 Feb 2013 18:38:03 +0000]
extcon: arizona: Fix interaction between headphone outputs and identification

Running HPDET while the headphone outputs are enabled can disrupt the
operation of HPDET. In order to avoid this HPDET needs to disable the
headphone outputs and ASoC needs to not enable them while HPDET is
running.

For extcon instead of checking if the headphone output is enabled when
doing magic application unconditionally disable the output and restore
the state which ASoC wants set when undoing the magic.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

6 years agoASoC: arizona: Fix interaction between headphone outputs and identification
Mark Brown [Fri, 22 Feb 2013 18:36:53 +0000]
ASoC: arizona: Fix interaction between headphone outputs and identification

Running HPDET while the headphone outputs are enabled can disrupt the
operation of HPDET. In order to avoid this HPDET needs to disable the
headphone outputs and ASoC needs to not enable them while HPDET is
running.

Do the ASoC side of this by storing the enable state in the core driver
structure and only writing to the device if a flag indicating that the
accessory detection side is in a state where it can have the headphone
output stage enabled.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

6 years agoextcon: arizona: Factor out magic application
Mark Brown [Tue, 12 Feb 2013 13:00:31 +0000]
extcon: arizona: Factor out magic application

We have a very similar sequence doing magic writes in several places
(one of which missed an update to interlock with the CODEC driver) so
factor it out into a function.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

6 years agoDrivers: hv: balloon: make local functions static
Wei Yongjun [Wed, 20 Mar 2013 15:25:59 +0000]
Drivers: hv: balloon: make local functions static

local functions that could be static.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agodummy-irq: introduce a dummy IRQ handler driver
Jiri Kosina [Wed, 20 Mar 2013 23:21:21 +0000]
dummy-irq: introduce a dummy IRQ handler driver

This module accepts a single 'irq' parameter, which it should register for.

Its sole purpose is to help with debugging of IRQ sharing problems, by
force-enabling IRQ that would otherwise be disabled.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomei: add mei_irq_compl_handler function
Tomas Winkler [Sun, 17 Mar 2013 09:41:20 +0000]
mei: add mei_irq_compl_handler function

similar to read/write add also irq completion handler
that is called for the irq thread

rename missnamed mei_irq_complete_handler to
mei_cl_complete_handler as it operates on a single client

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomemory: emif: Load the correct custom config values from dt
Lokesh Vutla [Sat, 16 Mar 2013 06:16:48 +0000]
memory: emif: Load the correct custom config values from dt

of_get_property returns value in Big Endian format.
Before using this value it should be converted to little endian
using be32_to_cpup().
Custom configs of emif are read from dt using of_get_property,
but these are not converted to litte endian format.
Correcting the same here.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomemory: emif: errata i743: Prohibit usage of Power-Down mode
Grygorii Strashko [Sat, 16 Mar 2013 06:16:47 +0000]
memory: emif: errata i743: Prohibit usage of Power-Down mode

ERRATA DESCRIPTION :
The EMIF supports power-down state for low power. The EMIF
automatically puts the SDRAM into power-down after the memory is
not accessed for a defined number of cycles and the
EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE bit field is set to 0x4.
As the EMIF supports automatic output impedance calibration, a ZQ
calibration long command is issued every time it exits active
power-down and precharge power-down modes. The EMIF waits and
blocks any other command during this calibration.
The EMIF does not allow selective disabling of ZQ calibration upon
exit of power-down mode. Due to very short periods of power-down
cycles, ZQ calibration overhead creates bandwidth issues and
increases overall system power consumption. On the other hand,
issuing ZQ calibration long commands when exiting self-refresh is
still required.

WORKAROUND :
Because there is no power consumption benefit of the power-down due
to the calibration and there is a performance risk, the guideline
is to not allow power-down state and, therefore, to not have set
the EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE bit field to 0x4.

This is applicable only for EMIF4D IP used in OMAP4 Soc's.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vitaly Chernooky <vitaly.chernooky@ti.com>
Signed-off-by: Oleksandr Dmytryshyn <oleksandr.dmytryshyn@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomemory: emif: Fix the incorrect 'size' parameter in memcpy
Oleksandr Dmytryshyn [Sat, 16 Mar 2013 06:16:46 +0000]
memory: emif: Fix the incorrect 'size' parameter in memcpy

The issue was that only the first timings table was added to the
emif platform data at the emif driver registration. All other
timings tables was filled with zeros. Now all emif timings table
are added to the platform data.

Signed-off-by: Oleksandr Dmytryshyn <oleksandr.dmytryshyn@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomemory: emif: use restart if power_off not present when out of spec
Nishanth Menon [Sat, 16 Mar 2013 06:16:45 +0000]
memory: emif: use restart if power_off not present when out of spec

Some machine or kernel variants might have missed implementation
of power off handlers. We DONOT want to let the system be in
"out of spec" state in this condition. So, WARN and attempt
a machine restart in the hopes of clearing the out-of-spec
temperature condition.

NOTE: This is not the safest option, but safer than leaving the
system in unstable conditions.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomemory: emif: Handle devices which are not rated for >85C
Nishanth Menon [Sat, 16 Mar 2013 06:16:44 +0000]
memory: emif: Handle devices which are not rated for >85C

As per JESD209-2E specification for LPDDR2,
      http://www.jedec.org/standards-documents/results/jesd209-2E
Table 73, LPDDR2 memories come in two flavors - Standard and
Extended. The Standard types can operate from -25C to +85C
However, beyond that and upto +105C can only be supported by
Extended types.

Unfortunately, it seems there is no info in MR0(device info) or
MR[1,2](device feature) for run time detection of this capability
as far as seen on the spec. Hence, we provide a custom_config
flag to be populated by platforms which have these "extended"
type memories.

For the "Standard" memories, we need to consider MR4 notifications
of temperature triggers >85C as equivalent to thermal shutdown
events (equivalent to Spec specified thermal shutdown events for
"extended" parts).

Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomemory: emif: handle overflow for timing for LP mode
Nishanth Menon [Sat, 16 Mar 2013 06:16:43 +0000]
memory: emif: handle overflow for timing for LP mode

In case the custom timings provide values which overflow
the maximum possible field value, warn and use maximum
permissible value.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomemory: emif: setup LP settings on freq update
Ambresh K [Sat, 16 Mar 2013 06:16:42 +0000]
memory: emif: setup LP settings on freq update

Program the power management shadow register on freq update
Else the concept of threshold frequencies dont really matter
as the system always uses the performance mode timing for LP
which is programmed in at init time.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomemory: emif: Fix the lpmode timeout calculation
Lokesh Vutla [Sat, 16 Mar 2013 06:16:41 +0000]
memory: emif: Fix the lpmode timeout calculation

The driver tries to round up the specified timeout cycles to
the next power of 2 value. This should be done defore updating
timeout variable.
Correcting this here.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agodrivers: char: Use PTR_RET function
Alexandru Gheorghiu [Sat, 16 Mar 2013 14:19:51 +0000]
drivers: char: Use PTR_RET function

Used PTR_RET function instead of IS_ERR and PTR_ERR.
Patch found using coccinelle.

Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoparport: use kmemdup instead of kmalloc + memcpy
Silviu-Mihai Popescu [Mon, 11 Mar 2013 16:39:22 +0000]
parport: use kmemdup instead of kmalloc + memcpy

This replaces calls to kmalloc followed by memcpy with a single call to
kmemdup. This was found via make coccicheck.

Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoparport: amiga: use module_platform_driver_probe()
Fabio Porcedda [Fri, 15 Mar 2013 10:49:27 +0000]
parport: amiga: use module_platform_driver_probe()

Use module_platform_driver_probe() macro which makes the code smaller
and simpler.

Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Matt Porter <mporter@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoMAINTAINERS: add ssbi
David Brown [Tue, 12 Mar 2013 18:41:55 +0000]
MAINTAINERS: add ssbi

The ssbi device is specific to the Qualcomm MSM SoCs.

Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoSSBI: Remove MSM_ prefix from SSBI drivers
David Brown [Tue, 12 Mar 2013 18:41:54 +0000]
SSBI: Remove MSM_ prefix from SSBI drivers

Although the SSBI sub is currently only used on MSM SoCs, it is still
a bus in its own right.  Remove this msm_ prefix from the driver and
it's symbols.  Clients can now refer directly to ssbi_write() and
ssbi_read().

Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agossbi: Remove extraneous logging
David Brown [Tue, 12 Mar 2013 18:41:53 +0000]
ssbi: Remove extraneous logging

Remove some unhelpful error logs.  This also removes the necessity of
having a pointer back to the struct device within the ssbi-specific
structure

Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agossbi: Use regular init level
David Brown [Tue, 12 Mar 2013 18:41:52 +0000]
ssbi: Use regular init level

With device tree, and deferred probe, it is no longer necessary to
make sure that the ssbi bus driver is initialized very early.  Restore
to a regular module_init().

Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agossbi: Comment the use of udelay()
David Brown [Tue, 12 Mar 2013 18:41:51 +0000]
ssbi: Comment the use of udelay()

The ssbi driver uses a busywait loop to read its status register.  Add
a comment explaining the timing of the device itself so that future
developers can better understand this delay, and possibly diagnose any
problems.

Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoSSBI: Convert SSBI to device tree
David Brown [Tue, 12 Mar 2013 18:41:50 +0000]
SSBI: Convert SSBI to device tree

The SSBI bus is exclusive to the Qualcomm MSM targets, and all SoCs
using it will be using device tree.  Convert this driver to indentify
with device tree.

This makes the bus probing a good bit simpler, since the attaching of
child nodes can be represented directly in the devicetree, rather than
having to be inferred by name.

Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agossbi: Allow compilation as a module
David Brown [Tue, 12 Mar 2013 18:41:49 +0000]
ssbi: Allow compilation as a module

The ssbi driver's read/write entry points are protected with wrappers
in the case when the driver isn't enabled.  These wrappers don't make
any sense, since a client of the SSBI bus won't work without it.  Make
these just regular functions, so that the SSBI driver can be built as
a module.

Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agossbi: Fix exit mismatch in remove function
David Brown [Tue, 12 Mar 2013 18:41:48 +0000]
ssbi: Fix exit mismatch in remove function

msm_ssbi_remove is referenced with __exit_p, but not declared with
__exit.  This causes a warning when the driver is not built as a
module:

drivers/ssbi/ssbi.c:341:23: warning: 'msm_ssbi_remove' defined but not used [-Wunused-function]

The remove is needed for unbinding to work, even if not compiled as a
module, so just remove it.

Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agofix: Use EXPORT_SYMBOL_GPL
David Brown [Tue, 12 Mar 2013 18:41:47 +0000]
fix: Use EXPORT_SYMBOL_GPL

Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoadd single-wire serial bus interface (SSBI) driver
Kenneth Heitke [Tue, 12 Mar 2013 18:41:46 +0000]
add single-wire serial bus interface (SSBI) driver

SSBI is the Qualcomm single-wire serial bus interface used to connect
the MSM devices to the PMIC and other devices.

Since SSBI only supports a single slave, the driver gets the name of the
slave device passed in from the board file through the master device's
platform data.

SSBI registers pretty early (postcore), so that the PMIC can come up
before the board init. This is useful if the board init requires the
use of gpios that are connected through the PMIC.

Based on a patch by Dima Zavin <dima@android.com> that can be found at:
http://android.git.kernel.org/?p=kernel/msm.git;a=commitdiff;h=eb060bac4

This patch adds PMIC Arbiter support for the MSM8660. The PMIC Arbiter
is a hardware wrapper around the SSBI 2.0 controller that is designed to
overcome concurrency issues and security limitations.  A controller_type
field is added to the platform data to specify the type of the SSBI
controller (1.0, 2.0, or PMIC Arbiter).

[davidb@codeaurora.org:
 I've moved this driver into drivers/ssbi/ and added an include for
 linux/module.h so that it will compile]

Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoLinux 3.9-rc4
Linus Torvalds [Sat, 23 Mar 2013 23:52:44 +0000]
Linux 3.9-rc4

6 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Linus Torvalds [Sat, 23 Mar 2013 23:51:55 +0000]
Merge git://git./linux/kernel/git/nab/target-pending

Pull SCSI target fixes from Nicholas Bellinger:
 "These are mostly minor fixes this time around.  The iscsi-target CHAP
  big-endian bugfix and bump FD_MAX_SECTORS=2048 default patch to allow
  1MB sized I/Os for FILEIO backends on >= v3.5 code are both CC'ed to
  stable.

  Also, there is a persistent reservations regression that has recently
  been reported for >= v3.8.x code, that is currently being tracked down
  for v3.9."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target/pscsi: Reject cross page boundary case in pscsi_map_sg
  target/file: Bump FD_MAX_SECTORS to 2048 to handle 1M sized I/Os
  tcm_vhost: Flush vhost_work in vhost_scsi_flush()
  tcm_vhost: Add missed lock in vhost_scsi_clear_endpoint()
  target: fix possible memory leak in core_tpg_register()
  target/iscsi: Fix mutual CHAP auth on big-endian arches
  target_core_sbc: use noop for SYNCHRONIZE_CACHE

6 years agoMerge tag 'md-3.9-fixes' of git://neil.brown.name/md
Linus Torvalds [Sat, 23 Mar 2013 22:49:49 +0000]
Merge tag 'md-3.9-fixes' of git://neil.brown.name/md

Pull md fixes from NeilBrown:
 "A few bugfixes for md

   - recent regressions in raid5
   - recent regressions in dmraid
   - a few instances of CONFIG_MULTICORE_RAID456 linger

  Several tagged for -stable"

* tag 'md-3.9-fixes' of git://neil.brown.name/md:
  md: remove CONFIG_MULTICORE_RAID456 entirely
  md/raid5: ensure sync and DISCARD don't happen at the same time.
  MD: Prevent sysfs operations on uninitialized kobjects
  MD RAID5: Avoid accessing gendisk or queue structs when not available
  md/raid5: schedule_construction should abort if nothing to do.

6 years agoMerge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik...
Linus Torvalds [Sat, 23 Mar 2013 19:33:36 +0000]
Merge tag 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev

Pull libata updates from Jeff Garzik:
 "Simple stuff.  See one-line summaries."

* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  pata_samsung_cf: use module_platform_driver_probe()
  [libata] Avoid specialized TLA's in ZPODD's Kconfig
  libata-acpi.c: fix copy and paste mistake in ata_acpi_register_power_resource
  sata_fsl: Remove redundant NULL check before kfree
  ahci: Add Device IDs for Intel Wellsburg PCH
  ata_piix: Add MODULE_PARM_DESC to prefer_ms_hyperv

6 years agoMerge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa...
Linus Torvalds [Sat, 23 Mar 2013 19:32:14 +0000]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux

Pull i2c fixes from Wolfram Sang:
 "One bugfix for the tegra driver.  Two updates regarding email
  addresses and MAINTAINERS which I like to have up-to-date so people
  can be reached immediately.  While we are here, there is on PCI_ID
  addition."

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: add maintainer entry for atmel i2c driver
  i2c: Fix my e-mail address in drivers and documentation
  i2c: iSMT: add Intel Avoton DeviceIDs
  i2c: tegra: check the clk_prepare_enable() return value

6 years agoMerge git://www.linux-watchdog.org/linux-watchdog
Linus Torvalds [Sat, 23 Mar 2013 19:30:39 +0000]
Merge git://www.linux-watchdog.org/linux-watchdog

Pull watchdog fixes from Wim Van Sebroeck:
 "Fix a boot issues and correct the AcpiMmioSel bitmask in the
  sp5100_tco watchdog device driver"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
  watchdog: sp5100_tco: Remove code that may cause a boot failure

6 years agoKMS: fix EDID detailed timing frame rate
Torsten Duwe [Sat, 23 Mar 2013 14:39:34 +0000]
KMS: fix EDID detailed timing frame rate

When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed.  Consecutive (debug-) output of that mode thus yields 0 for
vsync.  This simple fix also speeds up future invocations of
drm_mode_vrefresh().

While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.

Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agoKMS: fix EDID detailed timing vsync parsing
Torsten Duwe [Sat, 23 Mar 2013 14:38:22 +0000]
KMS: fix EDID detailed timing vsync parsing

EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these.  The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.

See

   http://en.wikipedia.org/wiki/EDID

and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.

Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agoMerge git://git.infradead.org/users/willy/linux-nvme
Linus Torvalds [Fri, 22 Mar 2013 23:43:53 +0000]
Merge git://git.infradead.org/users/willy/linux-nvme

Pull NVMe driver update from Matthew Wilcox:
 "These patches have mostly been baking for a few months; sorry I didn't
  get them in during the merge window.  They're all bug fixes, except
  for the addition of the SMART log and the addition to MAINTAINERS."

* git://git.infradead.org/users/willy/linux-nvme:
  NVMe: Add namespaces with no LBA range feature
  MAINTAINERS: Add entry for the NVMe driver
  NVMe: Initialize iod nents to 0
  NVMe: Define SMART log
  NVMe: Add result to nvme_get_features
  NVMe: Set result from user admin command
  NVMe: End queued bio requests when freeing queue
  NVMe: Free cmdid on nvme_submit_bio error

6 years agoMerge branch 'akpm' (fixes from Andrew)
Linus Torvalds [Fri, 22 Mar 2013 23:41:44 +0000]
Merge branch 'akpm' (fixes from Andrew)

Merge misc fixes from Andrew Morton.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
  mm/hotplug: only free wait_table if it's allocated by vmalloc
  dma-debug: update DMA debug API to better handle multiple mappings of a buffer
  dma-debug: fix locking bug in check_unmap()
  drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
  drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
  drivers/rtc/rtc-da9052.c: fix for rtc device registration
  mm: zone_end_pfn is too small
  poweroff: change orderly_poweroff() to use schedule_work()
  mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
  printk: Provide a wake_up_klogd() off-case
  irq_work.h: fix warning when CONFIG_IRQ_WORK=n

6 years agomqueue: sys_mq_open: do not call mnt_drop_write() if read-only
Vladimir Davydov [Fri, 22 Mar 2013 22:04:51 +0000]
mqueue: sys_mq_open: do not call mnt_drop_write() if read-only

mnt_drop_write() must be called only if mnt_want_write() succeeded,
otherwise the mnt_writers counter will diverge.

mnt_writers counters are used to check if remounting FS as read-only is
OK, so after an extra mnt_drop_write() call, it would be impossible to
remount mqueue FS as read-only.  Besides, on umount a warning would be
printed like this one:

  =====================================
  [ BUG: bad unlock balance detected! ]
  3.9.0-rc3 #5 Not tainted
  -------------------------------------
  a.out/12486 is trying to release lock (sb_writers) at:
  mnt_drop_write+0x1f/0x30
  but there are no more locks to release!

Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agomm/hotplug: only free wait_table if it's allocated by vmalloc
Jianguo Wu [Fri, 22 Mar 2013 22:04:50 +0000]
mm/hotplug: only free wait_table if it's allocated by vmalloc

zone->wait_table may be allocated from bootmem, it can not be freed.

Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Reviewed-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agodma-debug: update DMA debug API to better handle multiple mappings of a buffer
Alexander Duyck [Fri, 22 Mar 2013 22:04:49 +0000]
dma-debug: update DMA debug API to better handle multiple mappings of a buffer

There were reports of the igb driver unmapping buffers without calling
dma_mapping_error.  On closer inspection issues were found in the DMA
debug API and how it handled multiple mappings of the same buffer.

The issue I found is the fact that the debug_dma_mapping_error would
only set the map_err_type to MAP_ERR_CHECKED in the case that the was
only one match for device and device address.  However in the case of
non-IOMMU, multiple addresses existed and as a result it was not setting
this field once a second mapping was instantiated.  I have resolved this
by changing the search so that it instead will now set MAP_ERR_CHECKED
on the first buffer that matches the device and DMA address that is
currently in the state MAP_ERR_NOT_CHECKED.

A secondary side effect of this patch is that in the case of multiple
buffers using the same address only the last mapping will have a valid
map_err_type.  The previous mappings will all end up with map_err_type
set to MAP_ERR_CHECKED because of the dma_mapping_error call in
debug_dma_map_page.  However this behavior may be preferable as it means
you will likely only see one real error per multi-mapped buffer, versus
the current behavior of multiple false errors mer multi-mapped buffer.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
Tested-by: Shuah Khan <shuah.khan@hp.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agodma-debug: fix locking bug in check_unmap()
Alexander Duyck [Fri, 22 Mar 2013 22:04:48 +0000]
dma-debug: fix locking bug in check_unmap()

In check_unmap() it is possible to get into a dead-locked state if
dma_mapping_error is called.  The problem is that the bucket is locked in
check_unmap, and locked again by debug_dma_mapping_error which is called
by dma_mapping_error.  To resolve that we must release the lock on the
bucket before making the call to dma_mapping_error.

[akpm@linux-foundation.org: restore 80-col trickery to be consistent with the rest of the file]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
Tested-by: Shuah Khan <shuah.khan@hp.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agodrivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
Nicolas Ferre [Fri, 22 Mar 2013 22:04:47 +0000]
drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR

On some revisions of AT91 SoCs, the RTC IMR register is not working.
Instead of elaborating a workaround for that specific SoC or IP version,
we simply use a software variable to store the Interrupt Mask Register
and modify it for each enabling/disabling of an interrupt.  The overhead
of this is negligible anyway.

The interrupt mask register (IMR) for the RTC is broken on the AT91SAM9x5
sub-family of SoCs (good overview of the members here:
http://www.eewiki.net/display/linuxonarm/AT91SAM9x5 ).  The "user visible
effect" is the RTC doesn't work.

That sub-family is less than two years old and only has devicetree (DT)
support and came online circa lk 3.7 .  The dust is yet to settle on the
DT stuff at least for AT91 SoCs (translation: lots of stuff is still
broken, so much that it is hard to know where to start).

The fix in the patch is pretty simple: just shadow the silicon IMR
register with a variable in the driver.  Some older SoCs (pre-DT) use the
the rtc-at91rm9200 driver (e.g.  obviously the AT91RM9200) and they should
not be impacted by the change.  There shouldn't be a large volume of
interrupts associated with a RTC.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agodrivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
H Hartley Sweeten [Fri, 22 Mar 2013 22:04:45 +0000]
drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()

Commit be8678149701 ("drivers/video/ep93xx-fb.c: use devm_ functions")
introduced a build error:

  drivers/video/ep93xx-fb.c: In function 'ep93xxfb_probe':
  drivers/video/ep93xx-fb.c:532: error: implicit declaration of function 'devm_ioremap'
  drivers/video/ep93xx-fb.c:533: warning: assignment makes pointer from integer without a cast

Include <linux/io.h> to pickup the declaration of 'devm_ioremap'.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Cc: Damien Cassou <damien.cassou@lifl.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agodrivers/rtc/rtc-da9052.c: fix for rtc device registration
Ashish Jangam [Fri, 22 Mar 2013 22:04:44 +0000]
drivers/rtc/rtc-da9052.c: fix for rtc device registration

Add support for the virtual irq since now MFD only handles virtual irq
Without this patch rtc device will fail in registration.

(akpm: Ashish has a different version whcih will be needed for 3.8.x and
earlier kernels)

Signed-off-by: Ashish <ashish.jangam@kpitcummins.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agomm: zone_end_pfn is too small
Russ Anderson [Fri, 22 Mar 2013 22:04:43 +0000]
mm: zone_end_pfn is too small

Booting with 32 TBytes memory hits BUG at mm/page_alloc.c:552! (output
below).

The key hint is "page 4294967296 outside zone".
4294967296 = 0x100000000 (bit 32 is set).

The problem is in include/linux/mmzone.h:

  530 static inline unsigned zone_end_pfn(const struct zone *zone)
  531 {
  532         return zone->zone_start_pfn + zone->spanned_pages;
  533 }

zone_end_pfn is "unsigned" (32 bits).  Changing it to "unsigned long"
(64 bits) fixes the problem.

zone_end_pfn() was added recently in commit 108bcc96ef70 ("mm: add & use
zone_end_pfn() and zone_spans_pfn()")

Output from the failure.

  No AGP bridge found
  page 4294967296 outside zone [ 4294967296 - 4327469056 ]
  ------------[ cut here ]------------
  kernel BUG at mm/page_alloc.c:552!
  invalid opcode: 0000 [#1] SMP
  Modules linked in:
  CPU 0
  Pid: 0, comm: swapper Not tainted 3.9.0-rc2.dtp+ #10
  RIP: free_one_page+0x382/0x430
  Process swapper (pid: 0, threadinfo ffffffff81942000, task ffffffff81955420)
  Call Trace:
    __free_pages_ok+0x96/0xb0
    __free_pages+0x25/0x50
    __free_pages_bootmem+0x8a/0x8c
    __free_memory_core+0xea/0x131
    free_low_memory_core_early+0x4a/0x98
    free_all_bootmem+0x45/0x47
    mem_init+0x7b/0x14c
    start_kernel+0x216/0x433
    x86_64_start_reservations+0x2a/0x2c
    x86_64_start_kernel+0x144/0x153
  Code: 89 f1 ba 01 00 00 00 31 f6 d3 e2 4c 89 ef e8 66 a4 01 00 e9 2c fe ff ff 0f 0b eb fe 0f 0b 66 66 2e 0f 1f 84 00 00 00 00 00 eb f3 <0f> 0b eb fe 0f 0b 0f 1f 84 00 00 00 00 00 eb f6 0f 0b eb fe 49

Signed-off-by: Russ Anderson <rja@sgi.com>
Reported-by: George Beshers <gbeshers@sgi.com>
Acked-by: Hedi Berriche <hedi@sgi.com>
Cc: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agopoweroff: change orderly_poweroff() to use schedule_work()
Oleg Nesterov [Fri, 22 Mar 2013 22:04:41 +0000]
poweroff: change orderly_poweroff() to use schedule_work()

David said:

    Commit 6c0c0d4d1080 ("poweroff: fix bug in orderly_poweroff()")
    apparently fixes one bug in orderly_poweroff(), but introduces
    another.  The comments on orderly_poweroff() claim it can be called
    from any context - and indeed we call it from interrupt context in
    arch/powerpc/platforms/pseries/ras.c for example.  But since that
    commit this is no longer safe, since call_usermodehelper_fns() is not
    safe in interrupt context without the UMH_NO_WAIT option.

orderly_poweroff() can be used from any context but UMH_WAIT_EXEC is
sleepable.  Move the "force" logic into __orderly_poweroff() and change
orderly_poweroff() to use the global poweroff_work which simply calls
__orderly_poweroff().

While at it, remove the unneeded "int argc" and change argv_split() to
use GFP_KERNEL.

We use the global "bool poweroff_force" to pass the argument, this can
obviously affect the previous request if it is pending/running.  So we
only allow the "false => true" transition assuming that the pending
"true" should succeed anyway.  If schedule_work() fails after that we
know that work->func() was not called yet, it must see the new value.

This means that orderly_poweroff() becomes async even if we do not run
the command and always succeeds, schedule_work() can only fail if the
work is already pending.  We can export __orderly_poweroff() and change
the non-atomic callers which want the old semantics.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Feng Hong <hongfeng@marvell.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agomm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
Wanpeng Li [Fri, 22 Mar 2013 22:04:40 +0000]
mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting

hugetlb_total_pages is used for overcommit calculations but the current
implementation considers only the default hugetlb page size (which is
either the first defined hugepage size or the one specified by
default_hugepagesz kernel boot parameter).

If the system is configured for more than one hugepage size, which is
possible since commit a137e1cc6d6e ("hugetlbfs: per mount huge page
sizes") then the overcommit estimation done by __vm_enough_memory()
(resp.  shown by meminfo_proc_show) is not precise - there is an
impression of more available/allowed memory.  This can lead to an
unexpected ENOMEM/EFAULT resp.  SIGSEGV when memory is accounted.

Testcase:
  boot: hugepagesz=1G hugepages=1
  the default overcommit ratio is 50
  before patch:

    egrep 'CommitLimit' /proc/meminfo
    CommitLimit:     55434168 kB

  after patch:

    egrep 'CommitLimit' /proc/meminfo
    CommitLimit:     54909880 kB

[akpm@linux-foundation.org: coding-style tweak]
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [3.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agoprintk: Provide a wake_up_klogd() off-case
Frederic Weisbecker [Fri, 22 Mar 2013 22:04:39 +0000]
printk: Provide a wake_up_klogd() off-case

wake_up_klogd() is useless when CONFIG_PRINTK=n because neither printk()
nor printk_sched() are in use and there are actually no waiter on
log_wait waitqueue.  It should be a stub in this case for users like
bust_spinlocks().

Otherwise this results in this warning when CONFIG_PRINTK=n and
CONFIG_IRQ_WORK=n:

kernel/built-in.o In function `wake_up_klogd':
(.text.wake_up_klogd+0xb4): undefined reference to `irq_work_queue'

To fix this, provide an off-case for wake_up_klogd() when
CONFIG_PRINTK=n.

There is much more from console_unlock() and other console related code
in printk.c that should be moved under CONFIG_PRINTK.  But for now,
focus on a minimal fix as we passed the merged window already.

[akpm@linux-foundation.org: include printk.h in bust_spinlocks.c]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reported-by: James Hogan <james.hogan@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agoirq_work.h: fix warning when CONFIG_IRQ_WORK=n
James Hogan [Fri, 22 Mar 2013 22:04:37 +0000]
irq_work.h: fix warning when CONFIG_IRQ_WORK=n

A randconfig caught repeated compiler warnings when CONFIG_IRQ_WORK=n
due to the definition of a non-inline static function in
<linux/irq_work.h>:

  include/linux/irq_work.h +40 : warning: 'irq_work_needs_cpu' defined but not used

Make it inline to supress the warning.  This is caused commit
00b42959106a ("irq_work: Don't stop the tick with pending works") merged
in v3.9-rc1.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agowatchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
Takahisa Tanaka [Sun, 3 Mar 2013 05:48:00 +0000]
watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2

The AcpiMmioSel bit is bit 1 in the AcpiMmioEn register, but the current
sp5100_tco driver is using bit 2.

See 2.3.3 Power Management (PM) Registers page 150 of the
AMD SB800-Series Southbridges Register Reference Guide [1].

        AcpiMmioEn - RW – 8/16/32 bits - [PM_Reg: 24h]
        Field Name        Bits  Default  Description
        AcpiMMioDecodeEn  0     0b       Set to 1 to enable AcpiMMio space.
        AcpiMMIoSel       1     0b       Set AcpiMMio registers to be memory-mapped or IO-mapped space.
                                         0: Memory-mapped space
                                         1: I/O-mapped space

The sp5100_tco driver expects zero as a value of AcpiMmioSel (bit 1).

Fortunately, no problems were caused by this typo, because the default
value of the undocumented misused bit 2 seems to be zero.

However, the sp5100_tco driver should use the correct bitmask value.

[1] http://support.amd.com/us/Embedded_TechDocs/45482.pdf

Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>

6 years agowatchdog: sp5100_tco: Remove code that may cause a boot failure
Takahisa Tanaka [Sun, 3 Mar 2013 05:52:07 +0000]
watchdog: sp5100_tco: Remove code that may cause a boot failure

A problem was found on PC's with the SB700 chipset: The PC fails to
load BIOS after running the 3.8.x kernel until the power is completely
cut off. It occurs in all 3.8.x versions and the mainline version as of
2/4. The issue does not occur with the 3.7.x builds.

There are two methods for accessing the watchdog registers.

 1. Re-programming a resource address obtained by allocate_resource()
to chipset.
 2. Use the direct memory-mapped IO access.

The method 1 can be used by all the chipsets (SP5100, SB7x0, SB8x0 or
later). However, experience shows that only PC with the SB8x0 (or
later) chipsets can use the method 2.

This patch removes the method 1, because the critical problem was found.
That's why the watchdog timer was able to be used on SP5100 and SB7x0
chipsets until now.

Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1116835
Link: https://lkml.org/lkml/2013/2/14/271

Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>

6 years agoMerge git://git.kernel.org/pub/scm/virt/kvm/kvm
Linus Torvalds [Fri, 22 Mar 2013 19:57:30 +0000]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm

Pull KVM fix from Marcelo Tosatti:
 "Fix compilation on PPC with !CONFIG_KVM"

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  Revert "KVM: allow host header to be included even for !CONFIG_KVM"

6 years agoMerge tag 'usb-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Linus Torvalds [Fri, 22 Mar 2013 19:45:55 +0000]
Merge tag 'usb-3.9-rc3' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg Kroah-Hartman:
 "Here are a number of USB fixes that resolve issues that have been
  reported against 3.9-rc3."

* tag 'usb-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (37 commits)
  USB: ti_usb_3410_5052: fix use-after-free in TIOCMIWAIT
  USB: ssu100: fix use-after-free in TIOCMIWAIT
  USB: spcp8x5: fix use-after-free in TIOCMIWAIT
  USB: quatech2: fix use-after-free in TIOCMIWAIT
  USB: pl2303: fix use-after-free in TIOCMIWAIT
  USB: oti6858: fix use-after-free in TIOCMIWAIT
  USB: mos7840: fix use-after-free in TIOCMIWAIT
  USB: mos7840: fix broken TIOCMIWAIT
  USB: mct_u232: fix use-after-free in TIOCMIWAIT
  USB: io_ti: fix use-after-free in TIOCMIWAIT
  USB: io_edgeport: fix use-after-free in TIOCMIWAIT
  USB: ftdi_sio: fix use-after-free in TIOCMIWAIT
  USB: f81232: fix use-after-free in TIOCMIWAIT
  USB: cypress_m8: fix use-after-free in TIOCMIWAIT
  USB: ch341: fix use-after-free in TIOCMIWAIT
  USB: ark3116: fix use-after-free in TIOCMIWAIT
  USB: serial: add modem-status-change wait queue
  USB: serial: fix interface refcounting
  USB: io_ti: fix get_icount for two port adapters
  USB: garmin_gps: fix memory leak on disconnect
  ...

6 years agoMerge tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Linus Torvalds [Fri, 22 Mar 2013 19:45:08 +0000]
Merge tag 'sound-3.9' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
 "Mostly HD-audio and USB-audio regression fixes:
   - Oops fix at unloading of snd-hda-codec-conexant module
   - A few trivial regression fixes for Cirrus and Conexant HD-audio
     codecs
   - Relax the USB-audio descriptor parse errors as non-fatal
   - Fix locking of HD-audio CA0132 DSP loader
   - Fix the generic HD-audio parser for VIA codecs"

* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix DAC assignment for independent HP
  ALSA: hda - Fix abuse of snd_hda_lock_devices() for DSP loader
  ALSA: hda - Fix typo in checking IEC958 emphasis bit
  ALSA: snd-usb: mixer: ignore -EINVAL in snd_usb_mixer_controls()
  ALSA: snd-usb: mixer: propagate errors up the call chain
  ALSA: usb: Parse UAC2 extension unit like for UAC1
  ALSA: hda - Fix yet missing GPIO/EAPD setup in cirrus driver
  ALSA: hda/cirrus - Fix the digital beep registration
  ALSA: hda - Fix missing beep detach in patch_conexant.c
  ALSA: documentation: Fix typo in Documentation/sound

6 years agoMerge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Linus Torvalds [Fri, 22 Mar 2013 19:44:22 +0000]
Merge tag 'for_linus' of git://git./linux/kernel/git/bp/bp

Pull EDAC fixes from Borislav Petkov:
 "A fix from Mauro to correct csrow size accounting in sysfs and a
  sparse fix from Stephen Hemminger."

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  EDAC: Merge mci.mem_is_per_rank with mci.csbased
  amd64_edac: Correct DIMM sizes
  EDAC: Make sysfs functions static

6 years agoNVMe: Add namespaces with no LBA range feature
Keith Busch [Thu, 31 Jan 2013 21:40:38 +0000]
NVMe: Add namespaces with no LBA range feature

The LBA Range Type feature is optional in the NVMe specification,
so we should continue with adding namespaces for controllers that do
not implement this feature.

Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>

6 years agovfs,proc: guarantee unique inodes in /proc
Linus Torvalds [Fri, 22 Mar 2013 18:44:04 +0000]
vfs,proc: guarantee unique inodes in /proc

Dave Jones found another /proc issue with his Trinity tool: thanks to
the namespace model, we can have multiple /proc dentries that point to
the same inode, aliasing directories in /proc/<pid>/net/ for example.

This ends up being a total disaster, because it acts like hardlinked
directories, and causes locking problems.  We rely on the topological
sort of the inodes pointed to by dentries, and if we have aliased
directories, that odering becomes unreliable.

In short: don't do this.  Multiple dentries with the same (directory)
inode is just a bad idea, and the namespace code should never have
exposed things this way.  But we're kind of stuck with it.

This solves things by just always allocating a new inode during /proc
dentry lookup, instead of using "iget_locked()" to look up existing
inodes by superblock and number.  That actually simplies the code a bit,
at the cost of potentially doing more inode [de]allocations.

That said, the inode lookup wasn't free either (and did a lot of locking
of inodes), so it is probably not that noticeable.  We could easily keep
the old lookup model for non-directory entries, but rather than try to
be excessively clever this just implements the minimal and simplest
workaround for the problem.

Reported-and-tested-by: Dave Jones <davej@redhat.com>
Analyzed-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

6 years agoRevert "KVM: allow host header to be included even for !CONFIG_KVM"
Marcelo Tosatti [Fri, 22 Mar 2013 11:08:06 +0000]
Revert "KVM: allow host header to be included even for !CONFIG_KVM"

This reverts commit f445f11eb2cc265dd47da5b2e864df46cd6e5a82 as
it breaks PPC with CONFIG_KVM=n.

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>

6 years agoMAINTAINERS: add maintainer entry for atmel i2c driver
Ludovic Desroches [Fri, 15 Mar 2013 05:32:57 +0000]
MAINTAINERS: add maintainer entry for atmel i2c driver

Create an entry for atmel i2c driver: i2c-at91.c

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

6 years agoi2c: Fix my e-mail address in drivers and documentation
Guenter Roeck [Tue, 26 Feb 2013 06:03:52 +0000]
i2c: Fix my e-mail address in drivers and documentation

My old e-mail address is no longer working.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

6 years agoi2c: iSMT: add Intel Avoton DeviceIDs
Seth Heasley [Thu, 21 Feb 2013 12:30:43 +0000]
i2c: iSMT: add Intel Avoton DeviceIDs

This patch adds the iSMT SMBus Controller DeviceIDs for the Intel Avoton SOC.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

6 years agoi2c: tegra: check the clk_prepare_enable() return value
Laxman Dewangan [Fri, 15 Mar 2013 05:34:08 +0000]
i2c: tegra: check the clk_prepare_enable() return value

NVIDIA's Tegra SoC allows read/write of controller register only
if controller clock is enabled. System hangs if read/write happens
to registers without enabling clock.

clk_prepare_enable() can be fail due to unknown reason and hence
adding check for return value of this function. If this function
success then only access register otherwise return to caller with
error.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

6 years agoMerge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Linus Torvalds [Fri, 22 Mar 2013 00:59:22 +0000]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6

Pull CIFS fixes from Steve French:
 "Three small CIFS Fixes (the most important of the three fixes a recent
  problem authenticating to Windows 8 using cifs rather than SMB2)"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: ignore everything in SPNEGO blob after mechTypes
  cifs: delay super block destruction until all cifsFileInfo objects are gone
  cifs: map NT_STATUS_SHARING_VIOLATION to EBUSY instead of ETXTBSY

6 years agoMerge tag 'ext4_for_linue' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso...
Linus Torvalds [Fri, 22 Mar 2013 00:56:10 +0000]
Merge tag 'ext4_for_linue' of git://git./linux/kernel/git/tytso/ext4

Pull ext4 fixes from Ted Ts'o:
 "Fix a number of regression and other bugs in ext4, most of which were
  relatively obscure cornercases or races that were found using
  regression tests."

* tag 'ext4_for_linue' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (21 commits)
  ext4: fix data=journal fast mount/umount hang
  ext4: fix ext4_evict_inode() racing against workqueue processing code
  ext4: fix memory leakage in mext_check_coverage
  ext4: use s_extent_max_zeroout_kb value as number of kb
  ext4: use atomic64_t for the per-flexbg free_clusters count
  jbd2: fix use after free in jbd2_journal_dirty_metadata()
  ext4: reserve metadata block for every delayed write
  ext4: update reserved space after the 'correction'
  ext4: do not use yield()
  ext4: remove unused variable in ext4_free_blocks()
  ext4: fix WARN_ON from ext4_releasepage()
  ext4: fix the wrong number of the allocated blocks in ext4_split_extent()
  ext4: update extent status tree after an extent is zeroed out
  ext4: fix wrong m_len value after unwritten extent conversion
  ext4: add self-testing infrastructure to do a sanity check
  ext4: avoid a potential overflow in ext4_es_can_be_merged()
  ext4: invalidate extent status tree during extent migration
  ext4: remove unnecessary wait for extent conversion in ext4_fallocate()
  ext4: add warning to ext4_convert_unwritten_extents_endio
  ext4: disable merging of uninitialized extents
  ...

6 years agoUSB: ti_usb_3410_5052: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:26 +0000]
USB: ti_usb_3410_5052: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: ssu100: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:25 +0000]
USB: ssu100: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: spcp8x5: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:24 +0000]
USB: spcp8x5: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: quatech2: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:23 +0000]
USB: quatech2: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: pl2303: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:22 +0000]
USB: pl2303: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: oti6858: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:21 +0000]
USB: oti6858: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: mos7840: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:20 +0000]
USB: mos7840: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: mos7840: fix broken TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:19 +0000]
USB: mos7840: fix broken TIOCMIWAIT

Make sure waiting processes are woken on modem-status changes.

Currently processes are only woken on termios changes regardless of
whether the modem status has changed.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: mct_u232: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:18 +0000]
USB: mct_u232: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: io_ti: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:17 +0000]
USB: io_ti: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: io_edgeport: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:16 +0000]
USB: io_edgeport: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: ftdi_sio: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:15 +0000]
USB: ftdi_sio: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

When switching to tty ports, some lifetime assumptions were changed.
Specifically, close can now be called before the final tty reference is
dropped as part of hangup at device disconnect. Even with the ftdi
private-data refcounting this means that the port private data can be
freed while a process is sleeping on modem-status changes and thus
cannot be relied on to detect disconnects when woken up.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: f81232: fix use-after-free in TIOCMIWAIT
Johan Hovold [Tue, 19 Mar 2013 08:21:14 +0000]
USB: f81232: fix use-after-free in TIOCMIWAIT

Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.

This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>