Blackfin: move on-chip UART resources to boards files
Sonic Zhang [Wed, 9 Sep 2009 10:46:19 +0000 (10:46 +0000)]
Rather than keeping the pins in the actual driver and worrying about a
mess of Kconfig options, declare all the desired pin resources in the
boards file.  This lets people easily select the specific pins/ports for
the normal UART as well as GPIOs for CTS/RTS.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

22 files changed:
arch/blackfin/mach-bf518/boards/ezbrd.c
arch/blackfin/mach-bf527/boards/cm_bf527.c
arch/blackfin/mach-bf527/boards/ezbrd.c
arch/blackfin/mach-bf527/boards/ezkit.c
arch/blackfin/mach-bf533/boards/H8606.c
arch/blackfin/mach-bf533/boards/blackstamp.c
arch/blackfin/mach-bf533/boards/cm_bf533.c
arch/blackfin/mach-bf533/boards/ezkit.c
arch/blackfin/mach-bf533/boards/ip0x.c
arch/blackfin/mach-bf533/boards/stamp.c
arch/blackfin/mach-bf537/boards/cm_bf537e.c
arch/blackfin/mach-bf537/boards/cm_bf537u.c
arch/blackfin/mach-bf537/boards/minotaur.c
arch/blackfin/mach-bf537/boards/pnav10.c
arch/blackfin/mach-bf537/boards/stamp.c
arch/blackfin/mach-bf537/boards/tcm_bf537.c
arch/blackfin/mach-bf538/boards/ezkit.c
arch/blackfin/mach-bf548/boards/cm_bf548.c
arch/blackfin/mach-bf548/boards/ezkit.c
arch/blackfin/mach-bf561/boards/cm_bf561.c
arch/blackfin/mach-bf561/boards/ezkit.c
arch/blackfin/mach-bf561/boards/tepla.c

index 01975c0..0d1b021 100644 (file)
@@ -382,30 +382,93 @@ static struct platform_device bfin_spi1_device = {
 #endif  /* spi master and devices */
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
 #ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_THR,
+               .end = UART0_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
        {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+               .start = UART1_THR,
+               .end = UART1_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
-#endif
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
 };
 
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
        .name = "bfin-uart",
        .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -593,7 +656,12 @@ static struct platform_device *stamp_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index 7ab0800..2d93c1f 100644 (file)
@@ -603,30 +603,105 @@ static struct platform_device cm_flash_device = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
 #ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_THR,
+               .end = UART0_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
        {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+               .start = UART1_THR,
+               .end = UART1_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+       {       /* CTS pin */
+               .start = GPIO_PF9,
+               .end = GPIO_PF9,
+               .flags = IORESOURCE_IO,
+       },
+       {       /* RTS pin */
+               .start = GPIO_PF10,
+               .end = GPIO_PF10,
+               .flags = IORESOURCE_IO,
+       },
 #endif
 };
 
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
        .name = "bfin-uart",
        .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -829,7 +904,12 @@ static struct platform_device *cmbf527_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index cad23b1..3a981e8 100644 (file)
@@ -439,30 +439,105 @@ static struct platform_device bfin_spi0_device = {
 #endif  /* spi master and devices */
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
 #ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_THR,
+               .end = UART0_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
        {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+               .start = UART1_THR,
+               .end = UART1_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+       {       /* CTS pin */
+               .start = GPIO_PG0,
+               .end = GPIO_PG0,
+               .flags = IORESOURCE_IO,
+       },
+       {       /* RTS pin */
+               .start = GPIO_PF10,
+               .end = GPIO_PF10,
+               .flags = IORESOURCE_IO,
+       },
 #endif
 };
 
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
        .name = "bfin-uart",
        .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -665,7 +740,12 @@ static struct platform_device *stamp_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
 #endif
 
 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
index 5294fdd..0750e65 100644 (file)
@@ -647,30 +647,105 @@ static struct platform_device bfin_spi0_device = {
 #endif  /* spi master and devices */
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
 #ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_THR,
+               .end = UART0_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
        {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+               .start = UART1_THR,
+               .end = UART1_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+       {       /* CTS pin */
+               .start = GPIO_PF9,
+               .end = GPIO_PF9,
+               .flags = IORESOURCE_IO,
+       },
+       {       /* RTS pin */
+               .start = GPIO_PF10,
+               .end = GPIO_PF10,
+               .flags = IORESOURCE_IO,
+       },
 #endif
 };
 
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
        .name = "bfin-uart",
        .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -910,7 +985,12 @@ static struct platform_device *stamp_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index 4adceb0..cb3b74f 100644 (file)
@@ -257,21 +257,50 @@ static struct platform_device bfin_spi0_device = {
 #endif  /* spi master and devices */
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = BFIN_UART_THR,
+               .end = BFIN_UART_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX + 1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
 };
 
-static struct platform_device bfin_uart_device = {
+static struct platform_device bfin_uart0_device = {
        .name = "bfin-uart",
-       .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -394,7 +423,9 @@ static struct platform_device *h8606_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
 #endif
 
 #if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
index b580884..50ce3ec 100644 (file)
@@ -195,21 +195,50 @@ static struct platform_device bfin_spi0_device = {
 #endif  /* spi master and devices */
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = BFIN_UART_THR,
+               .end = BFIN_UART_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX + 1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
 };
 
-static struct platform_device bfin_uart_device = {
+static struct platform_device bfin_uart0_device = {
        .name = "bfin-uart",
-       .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -344,7 +373,9 @@ static struct platform_device *stamp_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index 7fc3b86..f707faf 100644 (file)
@@ -242,21 +242,50 @@ static struct platform_device smsc911x_device = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = BFIN_UART_THR,
+               .end = BFIN_UART_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX + 1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
 };
 
-static struct platform_device bfin_uart_device = {
+static struct platform_device bfin_uart0_device = {
        .name = "bfin-uart",
-       .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -432,7 +461,9 @@ static struct platform_device *cm_bf533_devices[] __initdata = {
        &bfin_dpmc,
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index d4689dc..5039247 100644 (file)
@@ -320,21 +320,50 @@ static struct platform_device bfin_spi0_device = {
 #endif  /* spi master and devices */
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = BFIN_UART_THR,
+               .end = BFIN_UART_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX + 1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
 };
 
-static struct platform_device bfin_uart_device = {
+static struct platform_device bfin_uart0_device = {
        .name = "bfin-uart",
-       .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -471,7 +500,9 @@ static struct platform_device *ezkit_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index 8ec42ba..a60d036 100644 (file)
@@ -19,6 +19,7 @@
 #include <linux/usb/isp1362.h>
 #endif
 #include <asm/irq.h>
+#include <asm/dma.h>
 #include <asm/bfin5xx_spi.h>
 #include <asm/portmux.h>
 
@@ -143,21 +144,50 @@ static struct platform_device spi_bfin_master_device = {
 #endif  /* spi master and devices */
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = BFIN_UART_THR,
+               .end = BFIN_UART_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX + 1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
 };
 
-static struct platform_device bfin_uart_device = {
+static struct platform_device bfin_uart0_device = {
        .name = "bfin-uart",
-       .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -241,7 +271,9 @@ static struct platform_device *ip0x_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index 6d68dcf..2683e5f 100644 (file)
@@ -322,21 +322,50 @@ static struct platform_device bfin_spi0_device = {
 #endif  /* spi master and devices */
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = BFIN_UART_THR,
+               .end = BFIN_UART_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX + 1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
 };
 
-static struct platform_device bfin_uart_device = {
+static struct platform_device bfin_uart0_device = {
        .name = "bfin-uart",
-       .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -495,7 +524,9 @@ static struct platform_device *stamp_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index c85f4d7..abb32dd 100644 (file)
@@ -329,8 +329,8 @@ static struct platform_device cm_flash_device = {
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_THR,
+               .end = UART0_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
        {
@@ -373,18 +373,25 @@ static struct resource bfin_uart0_resources[] = {
 #endif
 };
 
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
 static struct platform_device bfin_uart0_device = {
        .name = "bfin-uart",
        .id = 0,
        .num_resources = ARRAY_SIZE(bfin_uart0_resources),
        .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
 };
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
 static struct resource bfin_uart1_resources[] = {
        {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+               .start = UART1_THR,
+               .end = UART1_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
        {
@@ -427,11 +434,18 @@ static struct resource bfin_uart1_resources[] = {
 #endif
 };
 
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX, 0
+};
+
 static struct platform_device bfin_uart1_device = {
        .name = "bfin-uart",
        .id = 1,
        .num_resources = ARRAY_SIZE(bfin_uart1_resources),
        .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
 };
 #endif
 #endif
index ea11aa8..b3182fa 100644 (file)
@@ -327,25 +327,93 @@ static struct platform_device cm_flash_device = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_THR,
+               .end = UART0_GCTL+2,
                .flags = IORESOURCE_MEM,
-       }, {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+       },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+       {
+               .start = UART1_THR,
+               .end = UART1_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
 };
 
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
        .name = "bfin-uart",
        .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -522,7 +590,12 @@ static struct platform_device *cm_bf537u_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index 0da9272..58d6a20 100644 (file)
@@ -211,25 +211,93 @@ static struct platform_device bfin_spi0_device = {
 #endif  /* spi master and devices */
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_THR,
+               .end = UART0_GCTL+2,
                .flags = IORESOURCE_MEM,
-       }, {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+       },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+       {
+               .start = UART1_THR,
+               .end = UART1_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
 };
 
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
        .name = "bfin-uart",
        .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -343,7 +411,12 @@ static struct platform_device *minotaur_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index 4e0afda..3c36abd 100644 (file)
@@ -362,25 +362,93 @@ static struct platform_device bfin_fb_device = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_THR,
+               .end = UART0_GCTL+2,
                .flags = IORESOURCE_MEM,
-       }, {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+       },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+       {
+               .start = UART1_THR,
+               .end = UART1_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
 };
 
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
        .name = "bfin-uart",
        .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -472,7 +540,12 @@ static struct platform_device *stamp_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index ac9b52e..9842288 100644 (file)
@@ -1157,30 +1157,105 @@ static struct platform_device bfin_lq035q1_device = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
 #ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_THR,
+               .end = UART0_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+#ifdef CONFIG_BFIN_UART0_CTSRTS
+       {       /* CTS pin */
+               .start = GPIO_PG7,
+               .end = GPIO_PG7,
+               .flags = IORESOURCE_IO,
+       },
+       {       /* RTS pin */
+               .start = GPIO_PG6,
+               .end = GPIO_PG6,
+               .flags = IORESOURCE_IO,
+       },
+#endif
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
        {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+               .start = UART1_THR,
+               .end = UART1_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
-#endif
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX, 0
 };
 
-static struct platform_device bfin_uart_device = {
+static struct platform_device bfin_uart1_device = {
        .name = "bfin-uart",
        .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -1771,7 +1846,12 @@ static struct platform_device *stamp_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index 57163b6..d77ca5b 100644 (file)
@@ -327,25 +327,93 @@ static struct platform_device cm_flash_device = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_THR,
+               .end = UART0_GCTL+2,
                .flags = IORESOURCE_MEM,
-       }, {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+       },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+       {
+               .start = UART1_THR,
+               .end = UART1_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
 };
 
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
        .name = "bfin-uart",
        .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -524,7 +592,12 @@ static struct platform_device *cm_bf537_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index c296bb1..1912bc4 100644 (file)
@@ -41,37 +41,148 @@ static struct platform_device rtc_device = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
 #ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_THR,
+               .end = UART0_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+#ifdef CONFIG_BFIN_UART0_CTSRTS
+       {       /* CTS pin */
+               .start = GPIO_PG7,
+               .end = GPIO_PG7,
+               .flags = IORESOURCE_IO,
+       },
+       {       /* RTS pin */
+               .start = GPIO_PG6,
+               .end = GPIO_PG6,
+               .flags = IORESOURCE_IO,
+       },
+#endif
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
        {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+               .start = UART1_THR,
+               .end = UART1_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
+       .name = "bfin-uart",
+       .id = 1,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART2
+static struct resource bfin_uart2_resources[] = {
        {
-               .start = 0xFFC02100,
-               .end = 0xFFC021FF,
+               .start = UART2_THR,
+               .end = UART2_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
-#endif
+       {
+               .start = IRQ_UART2_RX,
+               .end = IRQ_UART2_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART2_ERROR,
+               .end = IRQ_UART2_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART2_TX,
+               .end = CH_UART2_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART2_RX,
+               .end = CH_UART2_RX,
+               .flags = IORESOURCE_DMA,
+       },
 };
 
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart2_peripherals[] = {
+       P_UART2_TX, P_UART2_RX, 0
+};
+
+static struct platform_device bfin_uart2_device = {
        .name = "bfin-uart",
-       .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .id = 2,
+       .num_resources = ARRAY_SIZE(bfin_uart2_resources),
+       .resource = bfin_uart2_resources,
+       .dev = {
+               .platform_data = &bfin_uart2_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -622,7 +733,15 @@ static struct platform_device *cm_bf538_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART2
+       &bfin_uart2_device,
+#endif
 #endif
 
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
index ccdcd6d..635f927 100644 (file)
@@ -127,44 +127,211 @@ static struct platform_device rtc_device = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
 #ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_DLL,
+               .end = UART0_RBR+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
        {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+               .start = UART1_DLL,
+               .end = UART1_RBR+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+       {       /* CTS pin -- 0 means not supported */
+               .start = GPIO_PE10,
+               .end = GPIO_PE10,
+               .flags = IORESOURCE_IO,
+       },
+       {       /* RTS pin -- 0 means not supported */
+               .start = GPIO_PE9,
+               .end = GPIO_PE9,
+               .flags = IORESOURCE_IO,
+       },
+#endif
+};
+
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX,
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+       P_UART1_RTS, P_UART1_CTS,
+#endif
+       0
+};
+
+static struct platform_device bfin_uart1_device = {
+       .name = "bfin-uart",
+       .id = 1,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART2
+static struct resource bfin_uart2_resources[] = {
        {
-               .start = 0xFFC02100,
-               .end = 0xFFC021FF,
+               .start = UART2_DLL,
+               .end = UART2_RBR+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART2_RX,
+               .end = IRQ_UART2_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART2_ERROR,
+               .end = IRQ_UART2_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART2_TX,
+               .end = CH_UART2_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART2_RX,
+               .end = CH_UART2_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart2_peripherals[] = {
+       P_UART2_TX, P_UART2_RX, 0
+};
+
+static struct platform_device bfin_uart2_device = {
+       .name = "bfin-uart",
+       .id = 2,
+       .num_resources = ARRAY_SIZE(bfin_uart2_resources),
+       .resource = bfin_uart2_resources,
+       .dev = {
+               .platform_data = &bfin_uart2_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART3
+static struct resource bfin_uart3_resources[] = {
        {
-               .start = 0xFFC03100,
-               .end = 0xFFC031FF,
+               .start = UART3_DLL,
+               .end = UART3_RBR+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART3_RX,
+               .end = IRQ_UART3_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART3_ERROR,
+               .end = IRQ_UART3_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART3_TX,
+               .end = CH_UART3_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART3_RX,
+               .end = CH_UART3_RX,
+               .flags = IORESOURCE_DMA,
+       },
+#ifdef CONFIG_BFIN_UART3_CTSRTS
+       {       /* CTS pin -- 0 means not supported */
+               .start = GPIO_PB3,
+               .end = GPIO_PB3,
+               .flags = IORESOURCE_IO,
+       },
+       {       /* RTS pin -- 0 means not supported */
+               .start = GPIO_PB2,
+               .end = GPIO_PB2,
+               .flags = IORESOURCE_IO,
+       },
 #endif
 };
 
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart3_peripherals[] = {
+       P_UART3_TX, P_UART3_RX,
+#ifdef CONFIG_BFIN_UART3_CTSRTS
+       P_UART3_RTS, P_UART3_CTS,
+#endif
+       0
+};
+
+static struct platform_device bfin_uart3_device = {
        .name = "bfin-uart",
-       .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .id = 3,
+       .num_resources = ARRAY_SIZE(bfin_uart3_resources),
+       .resource = bfin_uart3_resources,
+       .dev = {
+               .platform_data = &bfin_uart3_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -752,7 +919,18 @@ static struct platform_device *cm_bf548_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART2
+       &bfin_uart2_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART3
+       &bfin_uart3_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index 60193f7..1ed0261 100644 (file)
@@ -232,44 +232,211 @@ static struct platform_device rtc_device = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
 #ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = UART0_DLL,
+               .end = UART0_RBR+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART0_RX,
+               .end = IRQ_UART0_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART0_ERROR,
+               .end = IRQ_UART0_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART0_TX,
+               .end = CH_UART0_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART0_RX,
+               .end = CH_UART0_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
        {
-               .start = 0xFFC02000,
-               .end = 0xFFC020FF,
+               .start = UART1_DLL,
+               .end = UART1_RBR+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART1_RX,
+               .end = IRQ_UART1_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART1_ERROR,
+               .end = IRQ_UART1_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART1_TX,
+               .end = CH_UART1_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART1_RX,
+               .end = CH_UART1_RX,
+               .flags = IORESOURCE_DMA,
+       },
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+       {       /* CTS pin -- 0 means not supported */
+               .start = GPIO_PE10,
+               .end = GPIO_PE10,
+               .flags = IORESOURCE_IO,
+       },
+       {       /* RTS pin -- 0 means not supported */
+               .start = GPIO_PE9,
+               .end = GPIO_PE9,
+               .flags = IORESOURCE_IO,
+       },
+#endif
+};
+
+unsigned short bfin_uart1_peripherals[] = {
+       P_UART1_TX, P_UART1_RX,
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+       P_UART1_RTS, P_UART1_CTS,
+#endif
+       0
+};
+
+static struct platform_device bfin_uart1_device = {
+       .name = "bfin-uart",
+       .id = 1,
+       .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+       .resource = bfin_uart1_resources,
+       .dev = {
+               .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART2
+static struct resource bfin_uart2_resources[] = {
        {
-               .start = 0xFFC02100,
-               .end = 0xFFC021FF,
+               .start = UART2_DLL,
+               .end = UART2_RBR+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART2_RX,
+               .end = IRQ_UART2_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART2_ERROR,
+               .end = IRQ_UART2_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART2_TX,
+               .end = CH_UART2_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART2_RX,
+               .end = CH_UART2_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart2_peripherals[] = {
+       P_UART2_TX, P_UART2_RX, 0
+};
+
+static struct platform_device bfin_uart2_device = {
+       .name = "bfin-uart",
+       .id = 2,
+       .num_resources = ARRAY_SIZE(bfin_uart2_resources),
+       .resource = bfin_uart2_resources,
+       .dev = {
+               .platform_data = &bfin_uart2_peripherals, /* Passed to driver */
+       },
+};
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART3
+static struct resource bfin_uart3_resources[] = {
        {
-               .start = 0xFFC03100,
-               .end = 0xFFC031FF,
+               .start = UART3_DLL,
+               .end = UART3_RBR+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART3_RX,
+               .end = IRQ_UART3_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART3_ERROR,
+               .end = IRQ_UART3_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART3_TX,
+               .end = CH_UART3_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART3_RX,
+               .end = CH_UART3_RX,
+               .flags = IORESOURCE_DMA,
+       },
+#ifdef CONFIG_BFIN_UART3_CTSRTS
+       {       /* CTS pin -- 0 means not supported */
+               .start = GPIO_PB3,
+               .end = GPIO_PB3,
+               .flags = IORESOURCE_IO,
+       },
+       {       /* RTS pin -- 0 means not supported */
+               .start = GPIO_PB2,
+               .end = GPIO_PB2,
+               .flags = IORESOURCE_IO,
+       },
 #endif
 };
 
-static struct platform_device bfin_uart_device = {
+unsigned short bfin_uart3_peripherals[] = {
+       P_UART3_TX, P_UART3_RX,
+#ifdef CONFIG_BFIN_UART3_CTSRTS
+       P_UART3_RTS, P_UART3_CTS,
+#endif
+       0
+};
+
+static struct platform_device bfin_uart3_device = {
        .name = "bfin-uart",
-       .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .id = 3,
+       .num_resources = ARRAY_SIZE(bfin_uart3_resources),
+       .resource = bfin_uart3_resources,
+       .dev = {
+               .platform_data = &bfin_uart3_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -960,7 +1127,18 @@ static struct platform_device *ezkit_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+       &bfin_uart1_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART2
+       &bfin_uart2_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART3
+       &bfin_uart3_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index dfc8d5b..818266f 100644 (file)
@@ -305,21 +305,50 @@ static struct platform_device isp1362_hcd_device = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = BFIN_UART_THR,
+               .end = BFIN_UART_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART_RX,
+               .end = IRQ_UART_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART_ERROR,
+               .end = IRQ_UART_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART_TX,
+               .end = CH_UART_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART_RX,
+               .end = CH_UART_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
 };
 
-static struct platform_device bfin_uart_device = {
+static struct platform_device bfin_uart0_device = {
        .name = "bfin-uart",
-       .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -463,7 +492,9 @@ static struct platform_device *cm_bf561_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index ffd3e6a..c59041c 100644 (file)
@@ -160,21 +160,50 @@ static struct platform_device smc91x_device = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
        {
-               .start = 0xFFC00400,
-               .end = 0xFFC004FF,
+               .start = BFIN_UART_THR,
+               .end = BFIN_UART_GCTL+2,
                .flags = IORESOURCE_MEM,
        },
+       {
+               .start = IRQ_UART_RX,
+               .end = IRQ_UART_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART_ERROR,
+               .end = IRQ_UART_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART_TX,
+               .end = CH_UART_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART_RX,
+               .end = CH_UART_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
 };
 
-static struct platform_device bfin_uart_device = {
+static struct platform_device bfin_uart0_device = {
        .name = "bfin-uart",
-       .id = 1,
-       .num_resources = ARRAY_SIZE(bfin_uart_resources),
-       .resource = bfin_uart_resources,
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
 };
 #endif
+#endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
@@ -412,7 +441,9 @@ static struct platform_device *ezkit_devices[] __initdata = {
 #endif
 
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-       &bfin_uart_device,
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
 #endif
 
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
index 8ba7252..6c33397 100644 (file)
@@ -42,6 +42,52 @@ static struct platform_device smc91x_device = {
        .resource      = smc91x_resources,
 };
 
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
+       {
+               .start = BFIN_UART_THR,
+               .end = BFIN_UART_GCTL+2,
+               .flags = IORESOURCE_MEM,
+       },
+       {
+               .start = IRQ_UART_RX,
+               .end = IRQ_UART_RX+1,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = IRQ_UART_ERROR,
+               .end = IRQ_UART_ERROR,
+               .flags = IORESOURCE_IRQ,
+       },
+       {
+               .start = CH_UART_TX,
+               .end = CH_UART_TX,
+               .flags = IORESOURCE_DMA,
+       },
+       {
+               .start = CH_UART_RX,
+               .end = CH_UART_RX,
+               .flags = IORESOURCE_DMA,
+       },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+       P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+       .name = "bfin-uart",
+       .id = 0,
+       .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+       .resource = bfin_uart0_resources,
+       .dev = {
+               .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+       },
+};
+#endif
+#endif
+
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
@@ -73,6 +119,13 @@ static struct platform_device bfin_sir0_device = {
 
 static struct platform_device *tepla_devices[] __initdata = {
        &smc91x_device,
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+       &bfin_uart0_device,
+#endif
+#endif
+
 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 #ifdef CONFIG_BFIN_SIR0
        &bfin_sir0_device,