#include <linux/i2c.h>
#include <linux/i2c/tsc2007.h>
#include <linux/io.h>
+#include <linux/pinctrl/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
#include <linux/sh_intc.h>
#include <linux/sh_clk.h>
#include <media/soc_camera.h>
#include <sound/sh_fsi.h>
+#include <sound/simple_card.h>
#include <video/sh_mobile_hdmi.h>
#include <video/sh_mobile_lcdc.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
#include <asm/setup.h>
+#include "sh-gpio.h"
+
/*
* Address Interface BusWidth note
* ------------------------------------------------------------------
*
* SW41 : ON : SH-Mobile AP4 Audio Mode
* : OFF : Bluetooth Audio Mode
+ *
+ * it needs amixer settings for playing
+ *
+ * amixer set "Headphone Enable" on
*/
/*
* CN12: 3.3v
*/
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply fixed1v8_power_consumers[] =
+{
+ /* J22 default position: 1.8V */
+ REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+ REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
+ REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
+ REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
+};
+
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+ REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+ REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+};
+
+static struct regulator_consumer_supply dummy_supplies[] = {
+ REGULATOR_SUPPLY("vddvario", "smsc911x"),
+ REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
/* MTD */
static struct mtd_partition nor_flash_partitions[] = {
{
/*
* The card detect pin of the top SD/MMC slot (CN7) is active low and is
- * connected to GPIO A22 of SH7372 (GPIO_PORT41).
+ * connected to GPIO A22 of SH7372 (GPIO 41).
*/
static int slot_cn7_get_cd(struct platform_device *pdev)
{
- return !gpio_get_value(GPIO_PORT41);
+ return !gpio_get_value(41);
}
/* MERAM */
static struct sh_mobile_meram_info meram_info = {
static struct resource meram_resources[] = {
[0] = {
- .name = "MERAM",
- .start = 0xe8000000,
- .end = 0xe81fffff,
- .flags = IORESOURCE_MEM,
+ .name = "regs",
+ .start = 0xe8000000,
+ .end = 0xe807ffff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .name = "meram",
+ .start = 0xe8080000,
+ .end = 0xe81fffff,
+ .flags = IORESOURCE_MEM,
},
};
return;
/* set VBOUT/PWEN and EXTLP1 in DVSTCTR */
- __raw_writew(__raw_readw(0xE68B0008) | 0x600, 0xE68B0008);
+ __raw_writew(__raw_readw(IOMEM(0xE68B0008)) | 0x600, IOMEM(0xE68B0008));
}
static struct r8a66597_platdata usb1_host_data = {
};
/* MIPI-DSI */
-#define PHYCTRL 0x0070
static int sh_mipi_set_dot_clock(struct platform_device *pdev,
void __iomem *base,
int enable)
{
struct clk *pck = clk_get(&pdev->dev, "dsip_clk");
- void __iomem *phy = base + PHYCTRL;
if (IS_ERR(pck))
return PTR_ERR(pck);
if (enable) {
+ /*
+ * DSIPCLK = 24MHz
+ * D-PHY = DSIPCLK * ((0x6*2)+1) = 312MHz (see .phyctrl)
+ * HsByteCLK = D-PHY/8 = 39MHz
+ *
+ * X * Y * FPS =
+ * (544+72+600+16) * (961+8+8+2) * 30 = 36.1MHz
+ */
clk_set_rate(pck, clk_round_rate(pck, 24000000));
- iowrite32(ioread32(phy) | (0xb << 8), phy);
clk_enable(pck);
} else {
clk_disable(pck);
},
};
-static struct sh_mobile_lcdc_info lcdc_info;
-
static struct sh_mipi_dsi_info mipidsi0_info = {
.data_format = MIPI_RGB888,
- .lcd_chan = &lcdc_info.ch[0],
+ .channel = LCDC_CHAN_MAINLCD,
.lane = 2,
.vsynw_offset = 17,
+ .phyctrl = 0x6 << 8,
.flags = SH_MIPI_DSI_SYNC_PULSES_MODE |
SH_MIPI_DSI_HSbyteCLK,
.set_dot_clock = sh_mipi_set_dot_clock,
#endif
},
};
-static struct sh_mobile_meram_cfg lcd_meram_cfg = {
+
+static const struct sh_mobile_meram_cfg lcd_meram_cfg = {
.icb[0] = {
- .marker_icb = 28,
- .cache_icb = 24,
- .meram_offset = 0x0,
.meram_size = 0x40,
},
.icb[1] = {
- .marker_icb = 29,
- .cache_icb = 25,
- .meram_offset = 0x40,
.meram_size = 0x40,
},
};
.ch[0] = {
.chan = LCDC_CHAN_MAINLCD,
.fourcc = V4L2_PIX_FMT_RGB565,
- .lcd_cfg = ap4evb_lcdc_modes,
- .num_cfg = ARRAY_SIZE(ap4evb_lcdc_modes),
+ .lcd_modes = ap4evb_lcdc_modes,
+ .num_modes = ARRAY_SIZE(ap4evb_lcdc_modes),
.meram_cfg = &lcd_meram_cfg,
#ifdef CONFIG_AP4EVB_QHD
.tx_dev = &mipidsi0_device,
/* FSI */
#define IRQ_FSI evt2irq(0x1840)
-static int __fsi_set_rate(struct clk *clk, long rate, int enable)
-{
- int ret = 0;
-
- if (rate <= 0)
- return ret;
-
- if (enable) {
- ret = clk_set_rate(clk, rate);
- if (0 == ret)
- ret = clk_enable(clk);
- } else {
- clk_disable(clk);
- }
-
- return ret;
-}
-
-static int __fsi_set_round_rate(struct clk *clk, long rate, int enable)
-{
- return __fsi_set_rate(clk, clk_round_rate(clk, rate), enable);
-}
-
-static int fsi_ak4642_set_rate(struct device *dev, int rate, int enable)
-{
- struct clk *fsia_ick;
- struct clk *fsiack;
- int ret = -EIO;
-
- fsia_ick = clk_get(dev, "icka");
- if (IS_ERR(fsia_ick))
- return PTR_ERR(fsia_ick);
-
- /*
- * FSIACK is connected to AK4642,
- * and use external clock pin from it.
- * it is parent of fsia_ick now.
- */
- fsiack = clk_get_parent(fsia_ick);
- if (!fsiack)
- goto fsia_ick_out;
-
- /*
- * we get 1/1 divided clock by setting same rate to fsiack and fsia_ick
- *
- ** FIXME **
- * Because the freq_table of external clk (fsiack) are all 0,
- * the return value of clk_round_rate became 0.
- * So, it use __fsi_set_rate here.
- */
- ret = __fsi_set_rate(fsiack, rate, enable);
- if (ret < 0)
- goto fsiack_out;
-
- ret = __fsi_set_round_rate(fsia_ick, rate, enable);
- if ((ret < 0) && enable)
- __fsi_set_round_rate(fsiack, rate, 0); /* disable FSI ACK */
-
-fsiack_out:
- clk_put(fsiack);
-
-fsia_ick_out:
- clk_put(fsia_ick);
-
- return 0;
-}
-
-static int fsi_hdmi_set_rate(struct device *dev, int rate, int enable)
-{
- struct clk *fsib_clk;
- struct clk *fdiv_clk = &sh7372_fsidivb_clk;
- long fsib_rate = 0;
- long fdiv_rate = 0;
- int ackmd_bpfmd;
- int ret;
-
- switch (rate) {
- case 44100:
- fsib_rate = rate * 256;
- ackmd_bpfmd = SH_FSI_ACKMD_256 | SH_FSI_BPFMD_64;
- break;
- case 48000:
- fsib_rate = 85428000; /* around 48kHz x 256 x 7 */
- fdiv_rate = rate * 256;
- ackmd_bpfmd = SH_FSI_ACKMD_256 | SH_FSI_BPFMD_64;
- break;
- default:
- pr_err("unsupported rate in FSI2 port B\n");
- return -EINVAL;
- }
-
- /* FSI B setting */
- fsib_clk = clk_get(dev, "ickb");
- if (IS_ERR(fsib_clk))
- return -EIO;
-
- ret = __fsi_set_round_rate(fsib_clk, fsib_rate, enable);
- if (ret < 0)
- goto fsi_set_rate_end;
-
- /* FSI DIV setting */
- ret = __fsi_set_round_rate(fdiv_clk, fdiv_rate, enable);
- if (ret < 0) {
- /* disable FSI B */
- if (enable)
- __fsi_set_round_rate(fsib_clk, fsib_rate, 0);
- goto fsi_set_rate_end;
- }
-
- ret = ackmd_bpfmd;
-
-fsi_set_rate_end:
- clk_put(fsib_clk);
- return ret;
-}
-
-static int fsi_set_rate(struct device *dev, int is_porta, int rate, int enable)
-{
- int ret;
-
- if (is_porta)
- ret = fsi_ak4642_set_rate(dev, rate, enable);
- else
- ret = fsi_hdmi_set_rate(dev, rate, enable);
-
- return ret;
-}
-
static struct sh_fsi_platform_info fsi_info = {
- .porta_flags = SH_FSI_BRS_INV,
-
- .portb_flags = SH_FSI_BRS_INV |
- SH_FSI_BRM_INV |
- SH_FSI_LRS_INV |
- SH_FSI_FMT_SPDIF,
- .set_rate = fsi_set_rate,
+ .port_b = {
+ .flags = SH_FSI_CLK_CPG |
+ SH_FSI_FMT_SPDIF,
+ },
};
static struct resource fsi_resources[] = {
},
};
-static struct fsi_ak4642_info fsi2_ak4643_info = {
+static struct asoc_simple_card_info fsi2_ak4643_info = {
.name = "AK4643",
.card = "FSI2A-AK4643",
- .cpu_dai = "fsia-dai",
.codec = "ak4642-codec.0-0013",
.platform = "sh_fsi2",
- .id = FSI_PORT_A,
+ .daifmt = SND_SOC_DAIFMT_LEFT_J,
+ .cpu_dai = {
+ .name = "fsia-dai",
+ .fmt = SND_SOC_DAIFMT_CBS_CFS,
+ },
+ .codec_dai = {
+ .name = "ak4642-hifi",
+ .fmt = SND_SOC_DAIFMT_CBM_CFM,
+ .sysclk = 11289600,
+ },
};
static struct platform_device fsi_ak4643_device = {
- .name = "fsi-ak4642-audio",
+ .name = "asoc-simple-card",
.dev = {
- .platform_data = &fsi_info,
+ .platform_data = &fsi2_ak4643_info,
},
};
return error;
}
-static struct sh_mobile_meram_cfg hdmi_meram_cfg = {
+static const struct sh_mobile_meram_cfg hdmi_meram_cfg = {
.icb[0] = {
- .marker_icb = 30,
- .cache_icb = 26,
- .meram_offset = 0x80,
.meram_size = 0x100,
},
.icb[1] = {
- .marker_icb = 31,
- .cache_icb = 27,
- .meram_offset = 0x180,
.meram_size = 0x100,
},
};
},
};
+static struct asoc_simple_card_info fsi2_hdmi_info = {
+ .name = "HDMI",
+ .card = "FSI2B-HDMI",
+ .codec = "sh-mobile-hdmi",
+ .platform = "sh_fsi2",
+ .cpu_dai = {
+ .name = "fsib-dai",
+ .fmt = SND_SOC_DAIFMT_CBM_CFM | SND_SOC_DAIFMT_IB_NF,
+ },
+ .codec_dai = {
+ .name = "sh_mobile_hdmi-hifi",
+ },
+};
+
static struct platform_device fsi_hdmi_device = {
- .name = "sh_fsi2_b_hdmi",
+ .name = "asoc-simple-card",
+ .id = 1,
+ .dev = {
+ .platform_data = &fsi2_hdmi_info,
+ },
};
static struct gpio_led ap4evb_leds[] = {
{
.name = "led4",
- .gpio = GPIO_PORT185,
+ .gpio = 185,
.default_state = LEDS_GPIO_DEFSTATE_ON,
},
{
.name = "led2",
- .gpio = GPIO_PORT186,
+ .gpio = 186,
.default_state = LEDS_GPIO_DEFSTATE_ON,
},
{
.name = "led3",
- .gpio = GPIO_PORT187,
+ .gpio = 187,
.default_state = LEDS_GPIO_DEFSTATE_ON,
},
{
.name = "led1",
- .gpio = GPIO_PORT188,
+ .gpio = 188,
.default_state = LEDS_GPIO_DEFSTATE_ON,
}
};
static struct sh_mobile_ceu_info sh_mobile_ceu_info = {
.flags = SH_CEU_FLAG_USE_8BIT_BUS,
+ .max_width = 8188,
+ .max_height = 8188,
.csi2 = &csi2,
};
clk_put(hdmi_ick);
}
-static void __init fsi_init_pm_clock(void)
-{
- struct clk *fsia_ick;
- int ret;
-
- fsia_ick = clk_get(&fsi_device.dev, "icka");
- if (IS_ERR(fsia_ick)) {
- ret = PTR_ERR(fsia_ick);
- pr_err("Cannot get FSI ICK: %d\n", ret);
- return;
- }
-
- ret = clk_set_parent(fsia_ick, &sh7372_fsiack_clk);
- if (ret < 0)
- pr_err("Cannot set FSI-A parent: %d\n", ret);
-
- clk_put(fsia_ick);
-}
-
-/*
- * FIXME !!
- *
- * gpio_no_direction
- * are quick_hack.
- *
- * current gpio frame work doesn't have
- * the method to control only pull up/down/free.
- * this function should be replaced by correct gpio function
- */
-static void __init gpio_no_direction(u32 addr)
-{
- __raw_writeb(0x00, addr);
-}
-
/* TouchScreen */
#ifdef CONFIG_AP4EVB_QHD
# define GPIO_TSC_IRQ GPIO_FN_IRQ28_123
-# define GPIO_TSC_PORT GPIO_PORT123
+# define GPIO_TSC_PORT 123
#else /* WVGA */
# define GPIO_TSC_IRQ GPIO_FN_IRQ7_40
-# define GPIO_TSC_PORT GPIO_PORT40
+# define GPIO_TSC_PORT 40
#endif
#define IRQ28 evt2irq(0x3380) /* IRQ28A */
gpio_free(GPIO_TSC_IRQ);
- gpio_request(GPIO_TSC_PORT, NULL);
-
- gpio_direction_input(GPIO_TSC_PORT);
+ gpio_request_one(GPIO_TSC_PORT, GPIOF_IN, NULL);
val = gpio_get_value(GPIO_TSC_PORT);
},
};
-static struct map_desc ap4evb_io_desc[] __initdata = {
- /* create a 1:1 entity map for 0xe6xxxxxx
- * used by CPGA, INTC and PFC.
- */
- {
- .virtual = 0xe6000000,
- .pfn = __phys_to_pfn(0xe6000000),
- .length = 256 << 20,
- .type = MT_DEVICE_NONSHARED
- },
-};
-
-static void __init ap4evb_map_io(void)
-{
- iotable_init(ap4evb_io_desc, ARRAY_SIZE(ap4evb_io_desc));
- /* setup early devices and console here as well */
- sh7372_add_early_devices();
- shmobile_setup_console();
-}
+static const struct pinctrl_map ap4evb_pinctrl_map[] = {
+ /* MMCIF */
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh7372",
+ "mmc0_data8_0", "mmc0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh7372",
+ "mmc0_ctrl_0", "mmc0"),
+ /* SDHI0 */
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372",
+ "sdhi0_data4", "sdhi0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372",
+ "sdhi0_ctrl", "sdhi0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372",
+ "sdhi0_cd", "sdhi0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372",
+ "sdhi0_wp", "sdhi0"),
+ /* SDHI1 */
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-sh7372",
+ "sdhi1_data4", "sdhi1"),
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-sh7372",
+ "sdhi1_ctrl", "sdhi1"),
+};
-#define GPIO_PORT9CR 0xE6051009
-#define GPIO_PORT10CR 0xE605100A
-#define USCCR1 0xE6058144
+#define GPIO_PORT9CR IOMEM(0xE6051009)
+#define GPIO_PORT10CR IOMEM(0xE605100A)
+#define USCCR1 IOMEM(0xE6058144)
static void __init ap4evb_init(void)
{
+ struct pm_domain_device domain_devices[] = {
+ { "A4LC", &lcdc1_device, },
+ { "A4LC", &lcdc_device, },
+ { "A4MP", &fsi_device, },
+ { "A3SP", &sh_mmcif_device, },
+ { "A3SP", &sdhi0_device, },
+ { "A3SP", &sdhi1_device, },
+ { "A4R", &ceu_device, },
+ };
u32 srcr4;
struct clk *clk;
+ regulator_register_always_on(0, "fixed-1.8V", fixed1v8_power_consumers,
+ ARRAY_SIZE(fixed1v8_power_consumers), 1800000);
+ regulator_register_always_on(1, "fixed-3.3V", fixed3v3_power_consumers,
+ ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+ regulator_register_fixed(2, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
+ /* External clock source */
+ clk_set_rate(&sh7372_dv_clki_clk, 27000000);
+
+ pinctrl_register_mappings(ap4evb_pinctrl_map,
+ ARRAY_SIZE(ap4evb_pinctrl_map));
sh7372_pinmux_init();
/* enable SCIFA0 */
gpio_request(GPIO_FN_IRQ6_39, NULL);
/* enable Debug switch (S6) */
- gpio_request(GPIO_PORT32, NULL);
- gpio_request(GPIO_PORT33, NULL);
- gpio_request(GPIO_PORT34, NULL);
- gpio_request(GPIO_PORT35, NULL);
- gpio_direction_input(GPIO_PORT32);
- gpio_direction_input(GPIO_PORT33);
- gpio_direction_input(GPIO_PORT34);
- gpio_direction_input(GPIO_PORT35);
- gpio_export(GPIO_PORT32, 0);
- gpio_export(GPIO_PORT33, 0);
- gpio_export(GPIO_PORT34, 0);
- gpio_export(GPIO_PORT35, 0);
-
- /* SDHI0 */
- gpio_request(GPIO_FN_SDHICD0, NULL);
- gpio_request(GPIO_FN_SDHIWP0, NULL);
- gpio_request(GPIO_FN_SDHICMD0, NULL);
- gpio_request(GPIO_FN_SDHICLK0, NULL);
- gpio_request(GPIO_FN_SDHID0_3, NULL);
- gpio_request(GPIO_FN_SDHID0_2, NULL);
- gpio_request(GPIO_FN_SDHID0_1, NULL);
- gpio_request(GPIO_FN_SDHID0_0, NULL);
-
- /* SDHI1 */
- gpio_request(GPIO_FN_SDHICMD1, NULL);
- gpio_request(GPIO_FN_SDHICLK1, NULL);
- gpio_request(GPIO_FN_SDHID1_3, NULL);
- gpio_request(GPIO_FN_SDHID1_2, NULL);
- gpio_request(GPIO_FN_SDHID1_1, NULL);
- gpio_request(GPIO_FN_SDHID1_0, NULL);
-
- /* MMCIF */
- gpio_request(GPIO_FN_MMCD0_0, NULL);
- gpio_request(GPIO_FN_MMCD0_1, NULL);
- gpio_request(GPIO_FN_MMCD0_2, NULL);
- gpio_request(GPIO_FN_MMCD0_3, NULL);
- gpio_request(GPIO_FN_MMCD0_4, NULL);
- gpio_request(GPIO_FN_MMCD0_5, NULL);
- gpio_request(GPIO_FN_MMCD0_6, NULL);
- gpio_request(GPIO_FN_MMCD0_7, NULL);
- gpio_request(GPIO_FN_MMCCMD0, NULL);
- gpio_request(GPIO_FN_MMCCLK0, NULL);
+ gpio_request_one(32, GPIOF_IN | GPIOF_EXPORT, NULL);
+ gpio_request_one(33, GPIOF_IN | GPIOF_EXPORT, NULL);
+ gpio_request_one(34, GPIOF_IN | GPIOF_EXPORT, NULL);
+ gpio_request_one(35, GPIOF_IN | GPIOF_EXPORT, NULL);
/* USB enable */
gpio_request(GPIO_FN_VBUS0_1, NULL);
gpio_request(GPIO_FN_OVCN2_1, NULL);
/* setup USB phy */
- __raw_writew(0x8a0a, 0xE6058130); /* USBCR4 */
+ __raw_writew(0x8a0a, IOMEM(0xE6058130)); /* USBCR4 */
/* enable FSI2 port A (ak4643) */
gpio_request(GPIO_FN_FSIAIBT, NULL);
gpio_request(GPIO_FN_FSIAILR, NULL);
gpio_request(GPIO_FN_FSIAISLD, NULL);
gpio_request(GPIO_FN_FSIAOSLD, NULL);
- gpio_request(GPIO_PORT161, NULL);
- gpio_direction_output(GPIO_PORT161, 0); /* slave */
+ gpio_request_one(161, GPIOF_OUT_INIT_LOW, NULL); /* slave */
- gpio_request(GPIO_PORT9, NULL);
- gpio_request(GPIO_PORT10, NULL);
- gpio_no_direction(GPIO_PORT9CR); /* FSIAOBT needs no direction */
- gpio_no_direction(GPIO_PORT10CR); /* FSIAOLR needs no direction */
+ gpio_request(9, NULL);
+ gpio_request(10, NULL);
+ gpio_direction_none(GPIO_PORT9CR); /* FSIAOBT needs no direction */
+ gpio_direction_none(GPIO_PORT10CR); /* FSIAOLR needs no direction */
/* card detect pin for MMC slot (CN7) */
- gpio_request(GPIO_PORT41, NULL);
- gpio_direction_input(GPIO_PORT41);
+ gpio_request_one(41, GPIOF_IN, NULL);
/* setup FSI2 port B (HDMI) */
gpio_request(GPIO_FN_FSIBCK, NULL);
lcdc_info.ch[0].interface_type = RGB24;
lcdc_info.ch[0].clock_divider = 1;
lcdc_info.ch[0].flags = LCDC_FLAGS_DWPOL;
- lcdc_info.ch[0].lcd_size_cfg.width = 44;
- lcdc_info.ch[0].lcd_size_cfg.height = 79;
+ lcdc_info.ch[0].panel_cfg.width = 44;
+ lcdc_info.ch[0].panel_cfg.height = 79;
platform_add_devices(qhd_devices, ARRAY_SIZE(qhd_devices));
gpio_request(GPIO_FN_LCDDISP, NULL);
gpio_request(GPIO_FN_LCDDCK, NULL);
- gpio_request(GPIO_PORT189, NULL); /* backlight */
- gpio_direction_output(GPIO_PORT189, 1);
-
- gpio_request(GPIO_PORT151, NULL); /* LCDDON */
- gpio_direction_output(GPIO_PORT151, 1);
+ gpio_request_one(189, GPIOF_OUT_INIT_HIGH, NULL); /* backlight */
+ gpio_request_one(151, GPIOF_OUT_INIT_HIGH, NULL); /* LCDDON */
lcdc_info.clock_source = LCDC_CLK_BUS;
lcdc_info.ch[0].interface_type = RGB18;
lcdc_info.ch[0].clock_divider = 3;
lcdc_info.ch[0].flags = 0;
- lcdc_info.ch[0].lcd_size_cfg.width = 152;
- lcdc_info.ch[0].lcd_size_cfg.height = 91;
+ lcdc_info.ch[0].panel_cfg.width = 152;
+ lcdc_info.ch[0].panel_cfg.height = 91;
/* enable TouchScreen */
irq_set_irq_type(IRQ7, IRQ_TYPE_LEVEL_LOW);
gpio_request(GPIO_FN_HDMI_CEC, NULL);
/* Reset HDMI, must be held at least one EXTALR (32768Hz) period */
-#define SRCR4 0xe61580bc
+#define SRCR4 IOMEM(0xe61580bc)
srcr4 = __raw_readl(SRCR4);
__raw_writel(srcr4 | (1 << 13), SRCR4);
udelay(50);
platform_add_devices(ap4evb_devices, ARRAY_SIZE(ap4evb_devices));
- sh7372_add_device_to_domain(&sh7372_a4lc, &lcdc1_device);
- sh7372_add_device_to_domain(&sh7372_a4lc, &lcdc_device);
- sh7372_add_device_to_domain(&sh7372_a4mp, &fsi_device);
-
- sh7372_add_device_to_domain(&sh7372_a3sp, &sh_mmcif_device);
- sh7372_add_device_to_domain(&sh7372_a3sp, &sdhi0_device);
- sh7372_add_device_to_domain(&sh7372_a3sp, &sdhi1_device);
- sh7372_add_device_to_domain(&sh7372_a4r, &ceu_device);
+ rmobile_add_devices_to_domains(domain_devices,
+ ARRAY_SIZE(domain_devices));
hdmi_init_pm_clock();
- fsi_init_pm_clock();
sh7372_pm_init();
pm_clk_add(&fsi_device.dev, "spu2");
pm_clk_add(&lcdc1_device.dev, "hdmi");
}
-static void __init ap4evb_timer_init(void)
-{
- sh7372_clock_init();
- shmobile_timer.init();
-
- /* External clock source */
- clk_set_rate(&sh7372_dv_clki_clk, 27000000);
-}
-
-static struct sys_timer ap4evb_timer = {
- .init = ap4evb_timer_init,
-};
-
MACHINE_START(AP4EVB, "ap4evb")
- .map_io = ap4evb_map_io,
+ .map_io = sh7372_map_io,
+ .init_early = sh7372_add_early_devices,
.init_irq = sh7372_init_irq,
.handle_irq = shmobile_handle_irq_intc,
.init_machine = ap4evb_init,
- .timer = &ap4evb_timer,
+ .init_late = sh7372_pm_init_late,
+ .init_time = sh7372_earlytimer_init,
MACHINE_END