10 years agoe1000e: MDIO slow mode should always be done for 82577
Bruce Allan [Wed, 13 Jan 2010 01:52:49 +0000]
e1000e: MDIO slow mode should always be done for 82577

A previous 82577 workaround that set the MDIO access speed to slow mode for
every PHY register read/write when the cable is unplugged should instead
set the access mode to always be slow before any PHY register access.
Since the mode bit gets cleared when the PHY is reset, set the mode after
every PHY reset.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: update copyright dates
Shannon Nelson [Wed, 13 Jan 2010 01:49:34 +0000]
ixgbe: update copyright dates

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Do not attempt to perform interrupts in netpoll when down
Alexander Duyck [Wed, 13 Jan 2010 01:49:13 +0000]
ixgbe: Do not attempt to perform interrupts in netpoll when down

This patch resolves issues seen when running netconsole and rebooting via
reboot -f.  The issue was due to the fact that we were attempting to
perform interrupt actions when the q_vectors and rings had already been
freed via the ixgbe_shutdown routines.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Wed, 13 Jan 2010 05:33:49 +0000]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

10 years agosky2: Fix oops in sky2_xmit_frame() after TX timeout
Jarek Poplawski [Mon, 4 Jan 2010 08:48:41 +0000]
sky2: Fix oops in sky2_xmit_frame() after TX timeout

During TX timeout procedure dev could be awoken too early, e.g. by
sky2_complete_tx() called from sky2_down(). Then sky2_xmit_frame()
can run while buffers are freed causing an oops. This patch fixes it
by adding netif_device_present() test in sky2_tx_complete().

Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14925

With debugging by: Mike McCormack <mikem@ring3k.org>

Reported-by: Berck E. Nash <flyboy@gmail.com>
Tested-by: Berck E. Nash <flyboy@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agocfg80211: fix refcount imbalance when wext is disabled
Johannes Berg [Mon, 11 Jan 2010 15:14:57 +0000]
cfg80211: fix refcount imbalance when wext is disabled

When CONFIG_CFG80211_WEXT is not set, there is
a refcount imbalance with rdev->opencount, fix
that by moving it out of the ifdef.

Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: fix queue selection for data frames on monitor interfaces
Felix Fietkau [Mon, 11 Jan 2010 05:47:00 +0000]
mac80211: fix queue selection for data frames on monitor interfaces

When ieee80211_monitor_select_queue encounters data frames, it selects
the WMM AC based on skb->priority and assumes that skb->priority
contains a valid 802.1d tag. However this assumption is incorrect, since
ieee80211_select_queue has not been called at this point.
If skb->priority > 7, an array overrun occurs, which could lead to
invalid values, resulting in crashes in the tx path.
Fix this by setting skb->priority based on the 802.11 header for QoS
frames and using the default AC for all non-QoS frames.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoDocumentation/3c509: document ethtool support
Ben Hutchings [Mon, 11 Jan 2010 23:53:45 +0000]
Documentation/3c509: document ethtool support

3c509 was changed to support ethtool in 2002, making the 'xcvr' module
parameter obsolete in most cases.  More recently 3c509 was converted
to the modern driver model and this parameter was removed.  Fix the
documentation to refer to ethtool rather than the module parameter.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoaf_packet: Don't use skb after dev_queue_xmit()
Jarek Poplawski [Sun, 10 Jan 2010 22:04:19 +0000]
af_packet: Don't use skb after dev_queue_xmit()

tpacket_snd() can change and kfree an skb after dev_queue_xmit(),
which is illegal.

With debugging by: Stephen Hemminger <shemminger@vyatta.com>

Reported-by: Michael Breuer <mbreuer@majjas.com>
With help from: David S. Miller <davem@davemloft.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Michael Breuer<mbreuer@majjas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoiwlwifi: silence buffer overflow warning
Dan Carpenter [Sat, 9 Jan 2010 08:41:48 +0000]
iwlwifi: silence buffer overflow warning

Smatch (and presumably other static checkers) complain that MAX_TID_COUNT is
past the end of the array.  In the resulting discussion, Zhu Yi pointed out
that this value is not used in real life and the assignment was only there to
silence a gcc warning.

If there were a bug in the surrounding code and the value were used, the
WARN_ON(!qc) would print a warning before the crash.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agovxge: use pci_dma_mapping_error to test return value
Denis Kirjanov [Sun, 10 Jan 2010 21:40:10 +0000]
vxge: use pci_dma_mapping_error to test return value

pci_dma_mapping_error should be used to test return value of
pci_map_single or pci_map_page.

Signed-off-by: Denis Kirjanov <kirjanov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6
David S. Miller [Fri, 8 Jan 2010 21:15:47 +0000]
Merge branch 'master' of git://git./linux/kernel/git/kaber/nf-2.6

10 years agoiwlwifi: disable tx on beacon update notification
Abhijeet Kolekar [Fri, 8 Jan 2010 18:04:31 +0000]
iwlwifi: disable tx on beacon update notification

On beacon change update notification from mac we are not disabling
the tx in adhoc mode. Mac sends BSS_CHANGED_BEACON_ENABLED when
station leaves IBSS. Driver should indicate uCode to not to send
anything on receiving this notification.

Functionality to indicate uCode is duplicated across
two notifications so created a common function called iwl_set_no_assoc.

Fix the issue at
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2133.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwlwifi: fix iwl_queue_used bug when read_ptr == write_ptr
Zhu Yi [Fri, 8 Jan 2010 18:04:30 +0000]
iwlwifi: fix iwl_queue_used bug when read_ptr == write_ptr

When txq read_ptr equals to write_ptr, iwl_queue_used should
always return false. Because there is no used TFD in this case.

This is a complementary fix to the fix already included in commit "iwl3945:
fix panic in iwl3945 driver". Both fixes are needed to address the panic
below.

This problem was discussed on linux-wireless in
http://thread.gmane.org/gmane.linux.kernel.wireless.general/43568

<1>[ 7290.414172] IP: [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<4>[ 7290.414205] PGD 0
<1>[ 7290.414214] Thread overran stack, or stack corrupted
<0>[ 7290.414229] Oops: 0002 [#1] PREEMPT SMP
<0>[ 7290.414246] last sysfs file: /sys/devices/platform/coretemp.1/temp1_input
<4>[ 7290.414265] CPU 0
<4>[ 7290.414274] Modules linked in: af_packet nfsd usb_storage usb_libusual cpufreq_powersave exportfs cpufreq_conservative iwl3945 nfs cpufreq_userspace snd_hda_codec_realtek acpi_cpufreq uvcvideo lockd iwlcore snd_hda_intel joydev coretemp nfs_acl videodev snd_hda_codec mac80211 v4l1_compat snd_hwdep sbp2 v4l2_compat_ioctl32 uhci_hcd psmouse auth_rpcgss ohci1394 cfg80211 ehci_hcd video ieee1394 snd_pcm serio_raw battery ac nvidia(P) usbcore output sunrpc evdev lirc_ene0100 snd_page_alloc rfkill tg3 libphy fuse lzo lzo_decompress lzo_compress
<6>[ 7290.414486] Pid: 0, comm: swapper Tainted: P           2.6.32-rc8-wl #213 Aspire 5720
<6>[ 7290.414507] RIP: 0010:[<ffffffffa0dd53a1>]  [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<6>[ 7290.414541] RSP: 0018:ffff880002203d60  EFLAGS: 00010246
<6>[ 7290.414557] RAX: 000000000000004f RBX: ffff880064c11600 RCX: 0000000000000013
<6>[ 7290.414576] RDX: ffffffffa0ddcf20 RSI: ffff8800512b7008 RDI: 0000000000000038
<6>[ 7290.414596] RBP: ffff880002203dd0 R08: 0000000000000000 R09: 0000000000000100
<6>[ 7290.414616] R10: 0000000000000001 R11: 0000000000000000 R12: 00000000000000a0
<6>[ 7290.414635] R13: 0000000000000002 R14: 0000000000000013 R15: 0000000000020201
<6>[ 7290.414655] FS:  0000000000000000(0000) GS:ffff880002200000(0000) knlGS:0000000000000000
<6>[ 7290.414677] CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
<6>[ 7290.414693] CR2: 0000000000000041 CR3: 0000000001001000 CR4: 00000000000006f0
<6>[ 7290.414712] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
<6>[ 7290.414732] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
<4>[ 7290.414752] Process swapper (pid: 0, threadinfo ffffffff81524000, task ffffffff81528b60)
<0>[ 7290.414772] Stack:
<4>[ 7290.414780]  ffff880002203da0 0000000000000046 0000000000000000 0000000000000046
<4>[ 7290.414804] <0> 0000000000000282 0000000000000282 0000000000000282 ffff880064c12010
<4>[ 7290.414830] <0> ffff880002203db0 ffff880064c11600 ffff880064c12e50 ffff8800512b7000
<0>[ 7290.414858] Call Trace:
<0>[ 7290.414867]  <IRQ>
<4>[ 7290.414884]  [<ffffffffa0dc8c47>] iwl3945_irq_tasklet+0x657/0x1740 [iwl3945]
<4>[ 7290.414910]  [<ffffffff8138fc60>] ? _spin_unlock+0x30/0x60
<4>[ 7290.414931]  [<ffffffff81049a21>] tasklet_action+0x101/0x110
<4>[ 7290.414950]  [<ffffffff8104a3d0>] __do_softirq+0xc0/0x160
<4>[ 7290.414968]  [<ffffffff8100d01c>] call_softirq+0x1c/0x30
<4>[ 7290.414986]  [<ffffffff8100eff5>] do_softirq+0x75/0xb0
<4>[ 7290.415003]  [<ffffffff81049ee5>] irq_exit+0x95/0xa0
<4>[ 7290.415020]  [<ffffffff8100e547>] do_IRQ+0x77/0xf0
<4>[ 7290.415038]  [<ffffffff8100c7d3>] ret_from_intr+0x0/0xf
<0>[ 7290.415052]  <EOI>
<4>[ 7290.415067]  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415087]  [<ffffffff81234f04>] ? acpi_idle_enter_bm+0x27a/0x2a5
<4>[ 7290.415107]  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415130]  [<ffffffff812c11f3>] ? cpuidle_idle_call+0x93/0xf0
<4>[ 7290.415149]  [<ffffffff8100b0d7>] ? cpu_idle+0xa7/0x110
<4>[ 7290.415168]  [<ffffffff8137b3d5>] ? rest_init+0x75/0x80
<4>[ 7290.415187]  [<ffffffff8158cd0a>] ? start_kernel+0x3a7/0x3b3
<4>[ 7290.415206]  [<ffffffff8158c315>] ? x86_64_start_reservations+0x125/0x129
<4>[ 7290.415227]  [<ffffffff8158c3fd>] ? x86_64_start_kernel+0xe4/0xeb
<0>[ 7290.415243] Code: 00 41 39 ce 0f 8d e8 01 00 00 48 8b 47 40 48 63 d2 48 69 d2 98 00 00 00 4c 8b 04 02 48 c7 c2 20 cf dd a0 49 8d 78 38 49 8d 40 4f <c6> 47 09 00 c6 47 0c 00 c6 47 0f 00 c6 47 12 00 c6 47 15 00 49
<1>[ 7290.415382] RIP  [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<4>[ 7290.415410]  RSP <ffff880002203d60>
<0>[ 7290.415421] CR2: 0000000000000041
<4>[ 7290.415436] ---[ end trace ec46807277caa515 ]---
<0>[ 7290.415450] Kernel panic - not syncing: Fatal exception in interrupt
<4>[ 7290.415468] Pid: 0, comm: swapper Tainted: P      D    2.6.32-rc8-wl #213
<4>[ 7290.415486] Call Trace:
<4>[ 7290.415495]  <IRQ>  [<ffffffff8138c040>] panic+0x7d/0x13a
<4>[ 7290.415519]  [<ffffffff8101071a>] oops_end+0xda/0xe0
<4>[ 7290.415538]  [<ffffffff8102e1ea>] no_context+0xea/0x250
<4>[ 7290.415557]  [<ffffffff81038991>] ? select_task_rq_fair+0x511/0x780
<4>[ 7290.415578]  [<ffffffff8102e475>] __bad_area_nosemaphore+0x125/0x1e0
<4>[ 7290.415597]  [<ffffffff81038d0c>] ? __enqueue_entity+0x7c/0x80
<4>[ 7290.415616]  [<ffffffff81039201>] ? enqueue_task_fair+0x111/0x150
<4>[ 7290.415636]  [<ffffffff8102e53e>] bad_area_nosemaphore+0xe/0x10
<4>[ 7290.415656]  [<ffffffff8102e8fa>] do_page_fault+0x26a/0x320
<4>[ 7290.415674]  [<ffffffff813905df>] page_fault+0x1f/0x30
<4>[ 7290.415697]  [<ffffffffa0dd53a1>] ? iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945]
<4>[ 7290.415723]  [<ffffffffa0dc8c47>] iwl3945_irq_tasklet+0x657/0x1740 [iwl3945]
<4>[ 7290.415746]  [<ffffffff8138fc60>] ? _spin_unlock+0x30/0x60
<4>[ 7290.415764]  [<ffffffff81049a21>] tasklet_action+0x101/0x110
<4>[ 7290.415783]  [<ffffffff8104a3d0>] __do_softirq+0xc0/0x160
<4>[ 7290.415801]  [<ffffffff8100d01c>] call_softirq+0x1c/0x30
<4>[ 7290.415818]  [<ffffffff8100eff5>] do_softirq+0x75/0xb0
<4>[ 7290.415835]  [<ffffffff81049ee5>] irq_exit+0x95/0xa0
<4>[ 7290.415852]  [<ffffffff8100e547>] do_IRQ+0x77/0xf0
<4>[ 7290.415869]  [<ffffffff8100c7d3>] ret_from_intr+0x0/0xf
<4>[ 7290.415883]  <EOI>  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415911]  [<ffffffff81234f04>] ? acpi_idle_enter_bm+0x27a/0x2a5
<4>[ 7290.415931]  [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5
<4>[ 7290.415952]  [<ffffffff812c11f3>] ? cpuidle_idle_call+0x93/0xf0
<4>[ 7290.415971]  [<ffffffff8100b0d7>] ? cpu_idle+0xa7/0x110
<4>[ 7290.415989]  [<ffffffff8137b3d5>] ? rest_init+0x75/0x80
<4>[ 7290.416007]  [<ffffffff8158cd0a>] ? start_kernel+0x3a7/0x3b3
<4>[ 7290.416026]  [<ffffffff8158c315>] ? x86_64_start_reservations+0x125/0x129
<4>[ 7290.416047]  [<ffffffff8158c3fd>] ? x86_64_start_kernel+0xe4/0xeb

Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: fix endian error
Johannes Berg [Fri, 8 Jan 2010 18:00:00 +0000]
mac80211: fix endian error

I forgot to convert the radiotap length to
CPU endian, which sparse found thankfully.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: add missing sanity checks for action frames
Felix Fietkau [Thu, 7 Jan 2010 19:23:53 +0000]
mac80211: add missing sanity checks for action frames

Various missing sanity checks caused rejected action frames to be
interpreted as channel switch announcements, which can cause a client
mode interface to switch away from its operating channel, thereby losing
connectivity. This patch ensures that only spectrum management action
frames are processed by the CSA handling function and prevents rejected
action frames from getting processed by the MLME code.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: fix queue selection for packets injected via monitor interface
Lennert Buytenhek [Thu, 7 Jan 2010 14:01:42 +0000]
mac80211: fix queue selection for packets injected via monitor interface

Commit 'mac80211: fix skb buffering issue' added an ->ndo_select_queue()
for monitor interfaces which can end up dereferencing ieee802_1d_to_ac[]
beyond the end of the array for injected data packets (as skb->priority
isn't guaranteed to be zero or within [0:7]), which then triggers the
WARN_ON in net/core/dev.c:dev_cap_txqueue().  Fix this by always setting
the priority to zero on injected data frames.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agonetfilter: ebtables: enforce CAP_NET_ADMIN
Florian Westphal [Fri, 8 Jan 2010 16:31:24 +0000]
netfilter: ebtables: enforce CAP_NET_ADMIN

normal users are currently allowed to set/modify ebtables rules.
Restrict it to processes with CAP_NET_ADMIN.

Note that this cannot be reproduced with unmodified ebtables binary
because it uses SOCK_RAW.

Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>

10 years agoe1000e: fix and commonize code for setting the receive address registers
Bruce Allan [Thu, 7 Jan 2010 16:32:13 +0000]
e1000e: fix and commonize code for setting the receive address registers

Fix e1000e_rar_set() to flush consecutive register writes to avoid write
combining which some parts cannot handle.  Update e1000e_init_rx_addrs()
to call the fixed e1000e_rar_set() instead of duplicating code.

Also change e1000e_rar_set() to _not_ set the Address Valid bit if the MAC
address is all zeros.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoe1000e: e1000e_enable_tx_pkt_filtering() returns wrong value
Bruce Allan [Thu, 7 Jan 2010 16:31:54 +0000]
e1000e: e1000e_enable_tx_pkt_filtering() returns wrong value

e1000e_enable_tx_pkt_filtering() will return a non-zero value if the
driver fails to enable the manageability interface on the host for
any reason; instead it should retun zero to indicate filtering has been
disabled.  Also provide a single exit point for the function.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoe1000e: perform 10/100 adaptive IFS only on parts that support it
Bruce Allan [Thu, 7 Jan 2010 16:31:35 +0000]
e1000e: perform 10/100 adaptive IFS only on parts that support it

Adaptive IFS which involves writing to the Adaptive IFS Throttle register
was being done for all devices supported by the driver even though it is
not supported (i.e. the register doesn't even exist) on some devices.  The
feature is supported on 8257x/82583 and ICH/PCH based devices, but not
on ESB2.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoe1000e: don't accumulate PHY statistics on PHY read failure
Bruce Allan [Thu, 7 Jan 2010 16:31:16 +0000]
e1000e: don't accumulate PHY statistics on PHY read failure

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoe1000e: call pci_save_state() after pci_restore_state()
Bruce Allan [Thu, 7 Jan 2010 16:30:56 +0000]
e1000e: call pci_save_state() after pci_restore_state()

Due to a change in pci_restore_state()[1] which clears the saved_state
flag, the driver should call pci_save_state() to set the flag once again
to avoid issues with EEH (same fix that recently was submitted for ixgbe).

[1] commmit 4b77b0a2ba27d64f58f16d8d4d48d8319dda36ff

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetxen: update version to 4.0.72
Amit Kumar Salecha [Thu, 7 Jan 2010 22:10:17 +0000]
netxen: update version to 4.0.72

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetxen: fix set mac addr
Amit Kumar Salecha [Thu, 7 Jan 2010 22:10:16 +0000]
netxen: fix set mac addr

o If tx and rx resources are not available, during set mac request.
  Then this request wont be passed to firmware and it will be added to
  driver mac list and will never make it to firmware.
  So if resources are not available, don't add it to driver mac list.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetxen: fix smatch warning
Amit Kumar Salecha [Thu, 7 Jan 2010 22:10:15 +0000]
netxen: fix smatch warning

o Fix pointless assignments

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetxen: fix tx ring memory leak
Amit Kumar Salecha [Thu, 7 Jan 2010 22:10:14 +0000]
netxen: fix tx ring memory leak

o While unloading driver or resetting the context, tx ring was not
  getting free.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agotcp: update the netstamp_needed counter when cloning sockets
Octavian Purdila [Fri, 8 Jan 2010 08:00:09 +0000]
tcp: update the netstamp_needed counter when cloning sockets

This fixes a netstamp_needed accounting issue when the listen socket
has SO_TIMESTAMP set:

    s = socket(AF_INET, SOCK_STREAM, 0);
    setsockopt(s, SOL_SOCKET, SO_TIMESTAMP, 1); -> netstamp_needed = 1
    bind(s, ...);
    listen(s, ...);
    s2 = accept(s, ...); -> netstamp_needed = 1
    close(s2); -> netstamp_needed = 0
    close(s); -> netstamp_needed = -1

Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoTI DaVinci EMAC: Handle emac module clock correctly.
Sriram [Thu, 7 Jan 2010 00:22:37 +0000]
TI DaVinci EMAC: Handle emac module clock correctly.

In the driver probe function the emac module clock needs to
be enabled before calling register_netdev(). As soon as the
device is registered the driver get_stats function can be invoked
by the core - the module clock must be switched on to be able to
read from stats registers. Also explicitly call matching clk_disable
for failure conditions in probe function.

Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agodmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips
Ben Hutchings [Thu, 7 Jan 2010 02:41:51 +0000]
dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips

The Davicom DM9100 and DM9102 chips are used on the motherboards of
some SPARC systems (supported by the tulip driver) and also in PCI
expansion cards (supported by the dmfe driver).  There is no
difference in the PCI device ids for the two different configurations,
so these drivers both claim the device ids.  However, it is possible
to distinguish the two configurations by the presence of Open Firmware
properties for them, so we do that.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Fix compiler warning about variable being used uninitialized
PJ Waskiewicz [Wed, 6 Jan 2010 17:50:29 +0000]
ixgbe: Fix compiler warning about variable being used uninitialized

tc is still throwing a warning that is could be used
uninitialized.  This fixes it, and properly formats the device ID
checks for the use of this variable.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq()
Patrick McHardy [Thu, 7 Jan 2010 17:33:18 +0000]
netfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq()

As noticed by Dan Carpenter <error27@gmail.com>, update_nl_seq()
currently contains an out of bounds read of the seq_aft_nl array
when looking for the oldest sequence number position.

Fix it to only compare valid positions.

Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>

10 years agomv643xx_eth: don't include cache padding in rx desc buffer size
Saeed Bishara [Tue, 5 Jan 2010 09:15:32 +0000]
mv643xx_eth: don't include cache padding in rx desc buffer size

If NET_SKB_PAD is not a multiple of the cache line size, mv643xx_eth
allocates a couple of extra bytes at the start of each receive buffer
to make the data payload end up on a cache line boundary.

These extra bytes are skb_reserve()'d before DMA mapping, so they
should not be included in the DMA map byte count (as the mapping is
done starting at skb->data), nor should they be included in the
receive descriptor buffer size field, or the hardware can end up
DMAing beyond the end of the buffer, which can happen if someone
sends us a larger-than-MTU sized packet.

This problem was introduced in commit 7fd96ce47ff ("mv643xx_eth:
rework receive skb cache alignment", May 6 2009), but hasn't appeared
to be problematic so far, probably as the main users of mv643xx_eth
all have NET_SKB_PAD == L1_CACHE_BYTES.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoNET: atlx, fix memory leak
Jiri Slaby [Wed, 6 Jan 2010 06:54:16 +0000]
NET: atlx, fix memory leak

Stanse found a memory leak in atl2_get_eeprom. eeprom_buff is not
freed/assigned on all paths. Fix that.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: atl1-devel@lists.sourceforge.net
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agopcmcia: ncmlan_cs: remove odd bracket
Alexander Beregalov [Wed, 6 Jan 2010 13:05:46 +0000]
pcmcia: ncmlan_cs: remove odd bracket

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agocs89x0: Always report failure to request interrupt
Mark Brown [Thu, 7 Jan 2010 08:53:05 +0000]
cs89x0: Always report failure to request interrupt

A failure on request_irq() is always fatal but unlike other fatal
errors it's only reported to the user if net_debug is set. Make the
diagnostic unconditional and raise the priority so that errors are
more obvious to the user.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agohso: fixed missing newlines
Jan Dumon [Tue, 5 Jan 2010 04:53:00 +0000]
hso: fixed missing newlines

Fixed missing newlines in calls to dev_warn & dev_err.

Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agohso: Fix for 5 sec timeouts with v2.x firmware
Jan Dumon [Tue, 5 Jan 2010 04:52:42 +0000]
hso: Fix for 5 sec timeouts with v2.x firmware

Don't send flow control settings to any port other than the modem port.
Older firmware ignored this request but did sent a reply. Newer firmware just
ignores it without reply and causes a 5 second timeout every time a port
(except for the modem port) is opened or if tiocm settings are changed.

Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agohso: Attempt to recover from usb bus errors
Jan Dumon [Tue, 5 Jan 2010 04:52:13 +0000]
hso: Attempt to recover from usb bus errors

Attempt to reset the usb device when we receive usb bus errors.

Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agohso: don't change the state of a closed port
Jan Dumon [Tue, 5 Jan 2010 04:51:28 +0000]
hso: don't change the state of a closed port

Don't change the state of a port if it's not open. This fixes an issue where a
port sometimes has to be opened twice before data can be received.

Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agohso: Fix for endian issues on big endian machines
Jan Dumon [Tue, 5 Jan 2010 04:51:02 +0000]
hso: Fix for endian issues on big endian machines

Some fields are always little endian and have to be converted on big endian
machines.

Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agohso: Add Vendor/Product ID's for new devices
Jan Dumon [Tue, 5 Jan 2010 04:50:31 +0000]
hso: Add Vendor/Product ID's for new devices

Add product ID's for new devices.

Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoclaw: use "claw" as root device name
Ursula Braun [Mon, 4 Jan 2010 03:14:45 +0000]
claw: use "claw" as root device name

Claw module cannot be loaded together with qeth, because "qeth" has
been errorneously used as root device name. It is changed into "claw".

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agopcnet_cs: add cis of KTI PE520 pcmcia network card
Ken Kawasaki [Thu, 7 Jan 2010 04:37:58 +0000]
pcnet_cs: add cis of KTI PE520 pcmcia network card

pcnet_cs,serial_cs:

add cis of KTI PE520 pcmcia network card,
and serial card(Sierra Wireless AC860).

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoip: fix mc_loop checks for tunnels with multicast outer addresses
Octavian Purdila [Thu, 7 Jan 2010 04:37:01 +0000]
ip: fix mc_loop checks for tunnels with multicast outer addresses

When we have L3 tunnels with different inner/outer families
(i.e. IPV4/IPV6) which use a multicast address as the outer tunnel
destination address, multicast packets will be loopbacked back to the
sending socket even if IP*_MULTICAST_LOOP is set to disabled.

The mc_loop flag is present in the family specific part of the socket
(e.g. the IPv4 or IPv4 specific part).  setsockopt sets the inner
family mc_loop flag. When the packet is pushed through the L3 tunnel
it will eventually be processed by the outer family which if different
will check the flag in a different part of the socket then it was set.

Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoucc_geth: Fix the wrong the Rx/Tx FIFO size
Dave Liu [Thu, 7 Jan 2010 04:32:38 +0000]
ucc_geth: Fix the wrong the Rx/Tx FIFO size

current the Rx/Tx FIFO size settings cause problem
when four UEC ethernets work simultaneously.

eg: GETH1, UEM-J15, GETH2, UEC-J5 on 8569MDS board

 $ ifconfig eth0 10.193.20.166
 $ ifconfig eth1 10.193.20.167
 $ ifconfig eth2 10.193.20.168
 then
 $ ifconfig eth3 10.193.20.169

The fourth ethernet will cause all of interface broken,
you cann't ping successfully any more.
The patch fix this issue for MPC8569 Rev1.0 and Rev2.0

Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoRevert "mac80211: replace netif_tx_{start,stop,wake}_all_queues"
John W. Linville [Wed, 6 Jan 2010 20:39:39 +0000]
Revert "mac80211: replace netif_tx_{start,stop,wake}_all_queues"

This reverts commit 53623f1a09c7a7d23b74f0f7d93dba0ebde1006b.

This was inadvertantly missed in "mac80211: fix skb buffering issue",
and is required with that patch to restore proper queue operation.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: fix-up build breakage in 2.6.33
John W. Linville [Wed, 6 Jan 2010 20:35:49 +0000]
mac80211: fix-up build breakage in 2.6.33

"mac80211: fix skb buffering issue" is based on what will become 2.6.34,
so it includes an incompatible usage of sta_info_get.  This patch will
need to be effectively reverted when merging for 2.6.34.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agort2x00: Properly request tx headroom for alignment operations.
Gertjan van Wingerde [Wed, 30 Dec 2009 10:36:30 +0000]
rt2x00: Properly request tx headroom for alignment operations.

Current rt2x00 drivers may result in a "ieee80211_tx_status: headroom too
small" error message when a frame needs to be properly aligned before
transmitting it.
This is because the space needed to ensure proper alignment isn't
requested from mac80211.
Fix this by adding sufficient amount of alignment space to the amount
of headroom requested for TX frames.

Reported-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: fix skb buffering issue
Johannes Berg [Tue, 5 Jan 2010 17:00:58 +0000]
mac80211: fix skb buffering issue

Since I removed the master netdev, we've been
keeping internal queues only, and even before
that we never told the networking stack above
the virtual interfaces about congestion. This
means that packets are queued in mac80211 and
the upper layers never know, possibly leading
to memory exhaustion and other problems.

This patch makes all interfaces multiqueue and
uses ndo_select_queue to put the packets into
queues per AC. Additionally, when the driver
stops a queue, we now stop all corresponding
queues for the virtual interfaces as well.

The injection case will use VO by default for
non-data frames, and BE for data frames, but
downgrade any data frames according to ACM. It
needs to be fleshed out in the future to allow
chosing the queue/AC in radiotap.

Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agort2x00: Fix LED configuration setting for rt2800.
Gertjan van Wingerde [Wed, 30 Dec 2009 10:36:33 +0000]
rt2x00: Fix LED configuration setting for rt2800.

rt2800_blink_set uses an illegal value to set the LED_CFG_G_LED_MODE
field of the LED_CFG register. This field is only 2 bits large, so
should be initialized with value that fits. Use default value from
the vendor driver.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agort2x00: use correct headroom for transmission
Pavel Roskin [Wed, 30 Dec 2009 10:36:29 +0000]
rt2x00: use correct headroom for transmission

Use rt2x00dev->ops->extra_tx_headroom, not rt2x00dev->hw->extra_tx_headroom
in the tx code, as the later may include other headroom not to be used in
the chipset driver.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agocxgb3i: Fix flags test.
David S. Miller [Mon, 4 Jan 2010 22:36:40 +0000]
cxgb3i: Fix flags test.

As noticed by Stephen Rothwell.

Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agocfg80211: fix syntax error on user regulatory hints
Luis R. Rodriguez [Mon, 4 Jan 2010 16:37:39 +0000]
cfg80211: fix syntax error on user regulatory hints

This fixes a syntax error when setting up the user regulatory
hint. This change yields the same exact binary object though
so it ends up just being a syntax typo fix, fortunately.

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath5k: Fix eeprom checksum check for custom sized eeproms
Luis R. Rodriguez [Mon, 4 Jan 2010 15:40:39 +0000]
ath5k: Fix eeprom checksum check for custom sized eeproms

Commit 8bf3d79bc401ca417ccf9fc076d3295d1a71dbf5 enabled EEPROM
checksum checks to avoid bogus bug reports but failed to address
updating the code to consider devices with custom EEPROM sizes.
Devices with custom sized EEPROMs have the upper limit size stuffed
in the EEPROM. Use this as the upper limit instead of the static
default size. In case of a checksum error also provide back the
max size and whether or not this was the default size or a custom
one. If the EEPROM is busted we add a failsafe check to ensure
we don't loop forever or try to read bogus areas of hardware.

This closes bug 14874

http://bugzilla.kernel.org/show_bug.cgi?id=14874

Cc: stable@kernel.org
Cc: David Quan <david.quan@atheros.com>
Cc: Stephen Beahm <stephenbeahm@comcast.net>
Reported-by: Joshua Covington <joshuacov@googlemail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agozd1211rw: Fix multicast filtering.
Benoit Papillault [Sun, 3 Jan 2010 09:20:01 +0000]
zd1211rw: Fix multicast filtering.

If multicast parameter (as returned by zd_op_prepare_multicast) has
changed, no bit in changed_flags is set. To handle this situation, we do
not return if changed_flags is 0. If we do so, we will have some issue
with IPv6 which uses multicast for link layer address resolution.

Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwl: off by one bug
Dan Carpenter [Sun, 3 Jan 2010 09:19:35 +0000]
iwl: off by one bug

tid is used as an array offset.
agg = &priv->stations[sta_id].tid[tid].agg;
iwl4965_tx_status_reply_tx(priv, agg, tx_resp, txq_id, index);

It should be limitted to MAX_TID_COUNT - 1;
        struct iwl_tid_data tid[MAX_TID_COUNT];

regards,
dan carpenter

Signed-off-by: Dan Carpenter <error27@gmail.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomwl8k: fix configure_filter() memory leak on error
Lennert Buytenhek [Sat, 2 Jan 2010 09:31:42 +0000]
mwl8k: fix configure_filter() memory leak on error

If there was an error acquiring the firmware lock in
mwl8k_configure_filter(), we would end up leaking the multicast
command packet prepared by mwl8k_prepare_multicast().

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: fix ito64
Ming Lei [Tue, 29 Dec 2009 14:57:28 +0000]
ath9k: fix ito64

The unit of sizeof() is byte instead of bit, so fix it.
The patch can fix debug output of some dma_addr_t variables.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: Fix Kconfig depends for ATH9K_DEBUGFS
Dominik Geyer [Tue, 29 Dec 2009 07:27:57 +0000]
ath9k: Fix Kconfig depends for ATH9K_DEBUGFS

Add missing DEBUG_FS dependency for ATH9K_DEBUGFS in ath9k's Kconfig.

Signed-off-by: Dominik D. Geyer <dominik.geyer@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoipvs: Add boundary check on ioctl arguments
Arjan van de Ven [Mon, 4 Jan 2010 15:37:12 +0000]
ipvs: Add boundary check on ioctl arguments

The ipvs code has a nifty system for doing the size of ioctl command
copies; it defines an array with values into which it indexes the cmd
to find the right length.

Unfortunately, the ipvs code forgot to check if the cmd was in the
range that the array provides, allowing for an index outside of the
array, which then gives a "garbage" result into the length, which
then gets used for copying into a stack buffer.

Fix this by adding sanity checks on these as well as the copy size.

[ horms@verge.net.au: adjusted limit to IP_VS_SO_GET_MAX ]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>

10 years agonetxen: fix ethtool link test
Sucheta Chakraborty [Sat, 2 Jan 2010 03:25:19 +0000]
netxen: fix ethtool link test

o Fix ethtool link test for NX3031 chip.
o Remove unused code from phy interrupt callback

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetxen: fix ethtool register dump
Sucheta Chakraborty [Sat, 2 Jan 2010 03:25:18 +0000]
netxen: fix ethtool register dump

o Dump registers such as tx ring and rx ring counter, firmware state,
  niu regs, etc. which can be useful for debugging purpose.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agorrunner: fix buffer overflow
Dan Carpenter [Sat, 2 Jan 2010 04:08:46 +0000]
rrunner: fix buffer overflow

tx_skbuff is define as:
        struct sk_buff          *tx_skbuff[TX_RING_ENTRIES];

EVT_RING_ENTRIES is 64 and TX_RING_ENTRIES is 32.

This function is in a error path so that's why it wasn't noticed.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agobroadcom: Fix &&/|| confusion in bcm54xx_adjust_rxrefclk()
roel kluin [Wed, 30 Dec 2009 06:43:06 +0000]
broadcom: Fix &&/|| confusion in bcm54xx_adjust_rxrefclk()

This always evaluates to true.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonet: Test off by one in sh_eth_reset()
roel kluin [Wed, 30 Dec 2009 01:43:45 +0000]
net: Test off by one in sh_eth_reset()

If no break occurred, cnt reaches 0 after the loop.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoniu: timeout ignored in tcam_wait_bit()
roel kluin [Sun, 27 Dec 2009 04:10:59 +0000]
niu: timeout ignored in tcam_wait_bit()

With `while (--limit > 0)' i reaches 0 after the loop, so upon timeout the
error was not returned.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoatarilance: timeout ignored in lance_open()
roel kluin [Sun, 27 Dec 2009 03:26:12 +0000]
atarilance: timeout ignored in lance_open()

With `while (--i > 0)' i reaches 0 after the loop, so upon timeout the
error was not issued.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agodrivers/net : Correct the size argument to kzalloc
Julia Lawall [Tue, 29 Dec 2009 09:15:42 +0000]
drivers/net : Correct the size argument to kzalloc

lp->rx_skb has type struct sk_buff **, not struct sk_buff *, so the
elements of the array should have pointer type, not structure type.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@

  x =
  <+...sizeof(
- T
+ *x
  )...+>
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agocxgb3i: Fix a login over vlan issue
Rakesh Ranjan [Sun, 27 Dec 2009 07:03:08 +0000]
cxgb3i: Fix a login over vlan issue

Fix a target login issue, when parent interface is vlan and we are using cxgb3i sepecific
private ip address in '/etc/iscsi/ifaces/' iface file.

Acked-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Rakesh Ranjan <rakesh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agohamradio: avoid null deref v3
Dan Carpenter [Mon, 28 Dec 2009 06:54:55 +0000]
hamradio: avoid null deref v3

This should address the problems in version 1 (lazy) and version 2 (ugly).

Bump the stats on orig_dev not on the newly assigned NULL dev variable.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agousbnet: test off by one
roel kluin [Sun, 27 Dec 2009 11:22:08 +0000]
usbnet: test off by one

With `while (i++ < MII_TIMEOUT)' i reaches MII_TIMEOUT + 1 after the loop
This is probably unlikely a problem in practice.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agodrivers/net/can: Correct NULL test
Julia Lawall [Sun, 27 Dec 2009 11:27:44 +0000]
drivers/net/can: Correct NULL test

Test the just-allocated value for NULL rather than some other value.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x,y;
statement S;
@@

x = \(kmalloc\|kcalloc\|kzalloc\)(...);
(
if ((x) == NULL) S
|
if (
-   y
+   x
       == NULL)
 S
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agodrivers/isdn: eliminate duplicated test
Julia Lawall [Mon, 21 Dec 2009 14:25:32 +0000]
drivers/isdn: eliminate duplicated test

The code checked slot_rx twice.  Check slot_tx by analogy with the bank
case.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression E;
@@

(
*E && E
|
*E || E
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonet/sctp/socket.c: squish warning
Andrew Morton [Mon, 21 Dec 2009 14:25:06 +0000]
net/sctp/socket.c: squish warning

net/sctp/socket.c: In function 'sctp_setsockopt_autoclose':
net/sctp/socket.c:2090: warning: comparison is always false due to limited range of data type

Cc: Andrei Pelinescu-Onciul <andrei@iptel.org>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agorose_loopback_timer sets VC number <= ROSE_DEFAULT_MAXVC
Bernard Pidoux F6BVP [Thu, 17 Dec 2009 05:25:18 +0000]
rose_loopback_timer sets VC number <= ROSE_DEFAULT_MAXVC

cat /proc/net/rose displayed a rose sockets abnormal lci value, i.e.
greater than maximum number of VCs per neighbour allowed.
This number prevents further test of lci value during rose operations.

Example (lines shortened) :
[bernard]# cat /proc/net/rose
dest_addr  dest_call src_addr   src_call  dev   lci neigh st vs vr va
*          *         2080175520 F6BVP-1   rose0 000 00000  0  0  0  0
2080175520 FPAD-0    2080175520 WP-0      rose0 FFE 00001  3  0  0  0

Here are the default parameters :

linux/include/net/rose.h:#define ROSE_DEFAULT_MAXVC 50 /* Maximum number of VCs per neighbour */
linux/net/rose/af_rose.c:int sysctl_rose_maximum_vcs = ROSE_DEFAULT_MAXVC;

With the following patch, rose_loopback_timer() attributes a VC number
within limits.

Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agovia-velocity: Give RX descriptors to the NIC later on open or MTU change
Ben Hutchings [Mon, 14 Dec 2009 16:05:09 +0000]
via-velocity: Give RX descriptors to the NIC later on open or MTU change

velocity_open() calls velocity_give_many_rx_descs(), which gives RX
descriptors to the NIC, before installing an interrupt handler or
calling velocity_init_registers().  I think this is very unsafe and it
appears to explain the bug report <http://bugs.debian.org/508527>.

On MTU change, velocity_give_many_rx_descs() is again called before
velocity_init_registers().  I'm not sure whether this is unsafe but
it does look wrong.

Therefore, move the calls to velocity_give_many_rx_descs() after
request_irq() and velocity_init_registers().

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agofsl_pq_mdio: Fix iomem unmapping for non-eTSEC2.0 controllers
Anton Vorontsov [Wed, 30 Dec 2009 08:23:34 +0000]
fsl_pq_mdio: Fix iomem unmapping for non-eTSEC2.0 controllers

We use a rather complicated logic to support eTSEC and eTSEC2.0
registers maps in a single driver. Currently, the code tries to
unmap 'regs', but for non-eTSEC2.0 controllers 'regs' doesn't
point to a mapping start, and this might cause badness on probe
failure or module removal:

 Freescale PowerQUICC MII Bus: probed
 Trying to vfree() nonexistent vm area (e107f000)
 ------------[ cut here ]------------
 Badness at c00a7754 [verbose debug info unavailable]
 NIP: c00a7754 LR: c00a7754 CTR: c02231ec
 [...]
 NIP [c00a7754] __vunmap+0xec/0xf4
 LR [c00a7754] __vunmap+0xec/0xf4
 Call Trace:
 [df827e50] [c00a7754] __vunmap+0xec/0xf4 (unreliable)
 [df827e70] [c001519c] iounmap+0x44/0x54
 [df827e80] [c028b924] fsl_pq_mdio_probe+0x1cc/0x2fc
 [df827eb0] [c02fb9b4] of_platform_device_probe+0x5c/0x84
 [df827ed0] [c0229928] really_probe+0x78/0x1a8
 [df827ef0] [c0229b20] __driver_attach+0xa4/0xa8

Fix this by introducing a proper priv structure (finally!), which
now holds 'regs' and 'map' fields separately.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoucc_geth: Fix netdev watchdog triggering on suspend
Anton Vorontsov [Wed, 30 Dec 2009 08:23:32 +0000]
ucc_geth: Fix netdev watchdog triggering on suspend

Sometimes ucc_geth fails to suspend with the following trace:

 ucc_geth e0103000.ucc: suspend
 ucc_geth e0102000.ucc: suspend
 NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
 ------------[ cut here ]------------
 Badness at net/sched/sch_generic.c:255
 NIP: c021cb5c LR: c021cb5c CTR: c01ab4b4
 [...]
 NIP [c021cb5c] dev_watchdog+0x298/0x2a8
 LR [c021cb5c] dev_watchdog+0x298/0x2a8
 Call Trace:
 [c0389da0] [c021cb5c] dev_watchdog+0x298/0x2a8 (unreliable)
 [c0389e00] [c0031ed8] run_timer_softirq+0x16c/0x1dc
 [c0389e50] [c002c638] __do_softirq+0xa4/0x11c
 [...]

This patch fixes the issue by properly detaching the device on
suspend, and attaching it back on resume.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agophylib: Properly reinitialize PHYs after hibernation
Anton Vorontsov [Wed, 30 Dec 2009 08:23:30 +0000]
phylib: Properly reinitialize PHYs after hibernation

Since hibernation assumes power loss, we should fully reinitialize
PHYs (including platform fixups), as if PHYs were just attached.

This patch factors phy_init_hw() out of phy_attach_direct(), then
converts mdio_bus to dev_pm_ops and adds an appropriate restore()
callback.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agophylib: Fix deadlock on resume
Anton Vorontsov [Wed, 30 Dec 2009 08:23:28 +0000]
phylib: Fix deadlock on resume

Sometimes kernel hangs on resume with the following trace:

 ucc_geth e0102000.ucc: resume
 INFO: task bash:1764 blocked for more than 120 seconds.
 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
 bash          D 0fecf43c     0  1764   1763 0x00000000
 Call Trace:
 [cf9a7c10] [c0012868] ret_from_except+0x0/0x14 (unreliable)
 --- Exception: cf9a7ce0 at __switch_to+0x4c/0x6c
     LR = 0xcf9a7cc0
 [cf9a7cd0] [c0008c14] __switch_to+0x4c/0x6c (unreliable)
 [cf9a7ce0] [c028bcfc] schedule+0x158/0x260
 [cf9a7d10] [c028c720] __mutex_lock_slowpath+0x80/0xd8
 [cf9a7d40] [c01cf388] phy_stop+0x20/0x70
 [cf9a7d50] [c01d514c] ugeth_resume+0x6c/0x13c
 [...]

Here is why.

On suspend:

- PM core starts suspending devices, ucc_geth_suspend gets called;

- ucc_geth calls phy_stop() on suspend. Note that phy_stop() is
  mostly asynchronous so it doesn't block ucc_geth's suspend routine,
  it just sets PHY_HALTED state and disables PHY's interrupts;

- Suddenly the state machine gets scheduled, it grabs the phydev->lock
  mutex and tries to process the PHY_HALTED state, so it calls
  phydev->adjust_link(phydev->attached_dev). In ucc_geth case
  adjust_link() calls msleep(), which reschedules the code flow back to
  PM core, which now finishes suspend and so we end up sleeping with
  phydev->lock mutex held.

On resume:

- PM core starts resuming devices (notice that nobody rescheduled
  the state machine yet, so the mutex is still held), the core calls
  ucc_geth's resume routine;

- ucc_geth_resume restarts the PHY with phy_stop()/phy_start()
  sequence, and the phy_*() calls are trying to grab the phydev->lock
  mutex. Here comes the deadlock.

This patch fixes the issue by stopping the state machine on suspend
and starting it again on resume.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Wed, 30 Dec 2009 03:44:25 +0000]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

10 years agoRevert "b43: Enforce DMA descriptor memory constraints"
John W. Linville [Tue, 29 Dec 2009 19:07:42 +0000]
Revert "b43: Enforce DMA descriptor memory constraints"

This reverts commit 9bd568a50c446433038dec2a5186c5c57c3dbd23.

That commit is shown to cause allocation failures during initialization
on some machines.

http://bugzilla.kernel.org/show_bug.cgi?id=14844

Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwmc3200wifi: fix array out-of-boundary access
Zhu Yi [Mon, 28 Dec 2009 06:23:11 +0000]
iwmc3200wifi: fix array out-of-boundary access

Allocate priv->rx_packets[IWM_RX_ID_HASH + 1] because the max array
index is IWM_RX_ID_HASH according to IWM_RX_ID_GET_HASH().

Cc: stable@kernel.org
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agowl1251: timeout one too soon in wl1251_boot_run_firmware()
Roel Kluin [Sat, 26 Dec 2009 19:31:59 +0000]
wl1251: timeout one too soon in wl1251_boot_run_firmware()

`loop' reaches INIT_LOOP + 1 after the loop. so if ACX_INTR_INIT_COMPLETE
occurs in the last iteration the write occurs but also the error out as if a
timeout occurred. This is probably very unlikely to ever occur.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: fix propagation of failed hardware reconfigurations
Luis R. Rodriguez [Thu, 24 Dec 2009 20:38:22 +0000]
mac80211: fix propagation of failed hardware reconfigurations

mac80211 does not propagate failed hardware reconfiguration
requests. For suspend and resume this is important due to all
the possible issues that can come out of the suspend <-> resume
cycle. Not propagating the error means cfg80211 will assume
the resume for the device went through fine and mac80211 will
continue on trying to poke at the hardware, enable timers,
queue work, and so on for a device which is completley
unfunctional.

The least we can do is to propagate device start issues and
warn when this occurs upon resume. A side effect of this patch
is we also now propagate the start errors upon harware
reconfigurations (non-suspend), but this should also be desirable
anyway, there is not point in continuing to reconfigure a
device if mac80211 was unable to start the device.

For further details refer to the thread:

http://marc.info/?t=126151038700001&r=1&w=2

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: fix race with suspend and dynamic_ps_disable_work
Luis R. Rodriguez [Thu, 24 Dec 2009 20:26:09 +0000]
mac80211: fix race with suspend and dynamic_ps_disable_work

When mac80211 suspends it calls a driver's suspend callback
as a last step and after that the driver assumes no calls will
be made to it until we resume and its start callback is kicked.
If such calls are made, however, suspend can end up throwing
hardware in an unexpected state and making the device unusable
upon resume.

Fix this by preventing mac80211 to schedule dynamic_ps_disable_work
by checking for when mac80211 starts to suspend and starts
quiescing. Frames should be allowed to go through though as
that is part of the quiescing steps and we do not flush the
mac80211 workqueue since it was already done towards the
beginning of suspend cycle.

The other mac80211 issue will be hanled in the next patch.

For further details see refer to the thread:

http://marc.info/?t=126144866100001&r=1&w=2

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: fix missed error codes in the tx status check
Felix Fietkau [Thu, 24 Dec 2009 13:04:32 +0000]
ath9k: fix missed error codes in the tx status check

My previous change added in:

 commit 815833e7ecf0b9a017315cae6aef4d7cd9517681
    ath9k: fix tx status reporting

was not checking all possible tx error conditions. This could possibly
lead to throughput issues due to slow rate control adaption or missed
retransmissions of failed A-MPDU frames.

This patch adds a mask for all possible error conditions and uses it
in the xmit ok check.

Cc: stable@kernel.org
Reported-by: Bj√∂rn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: wake hardware during AMPDU TX actions
Luis R. Rodriguez [Thu, 24 Dec 2009 01:03:29 +0000]
ath9k: wake hardware during AMPDU TX actions

AMDPDU actions poke hardware for TX operation, as such
we want to turn hardware on for these actions. AMDPU RX operations
do not require hardware on as nothing is done in hardware for
those actions. Without this we cannot guarantee hardware has
been programmed correctly for each AMPDU TX action.

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: wake hardware for interface IBSS/AP/Mesh removal
Luis R. Rodriguez [Thu, 24 Dec 2009 01:03:28 +0000]
ath9k: wake hardware for interface IBSS/AP/Mesh removal

When we remove a IBSS/AP/Mesh interface we stop DMA
but to do this we should ensure hardware is on. Awaken
the device prior to these calls. This should ensure
DMA is stopped upon suspend and plain device removal.

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: fix suspend by waking device prior to stop
Sujith [Thu, 24 Dec 2009 01:03:27 +0000]
ath9k: fix suspend by waking device prior to stop

Ensure the device is awake prior to trying to tell hardware
to stop it. Impact of not doing this is we can likely leave
the device in an undefined state likely causing issues with
suspend and resume. This patch ensures harware is where it
should be prior to suspend.

Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agocfg80211: fix error path in cfg80211_wext_siwscan
Johannes Berg [Wed, 23 Dec 2009 14:33:35 +0000]
cfg80211: fix error path in cfg80211_wext_siwscan

If there's an invalid channel or SSID, the code leaks
the scan request. Always free the scan request, unless
it was successfully given to the driver.

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agowl1271_cmd.c: cleanup char => u8
Dan Carpenter [Wed, 23 Dec 2009 13:23:19 +0000]
wl1271_cmd.c: cleanup char => u8

This is just a clean up and doesn't make a functional difference.  It keeps the
lint checkers happy.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwlwifi: Storage class should be before const qualifier
Tobias Klauser [Wed, 23 Dec 2009 13:18:11 +0000]
iwlwifi: Storage class should be before const qualifier

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: Storage class should be before const qualifier
Tobias Klauser [Wed, 23 Dec 2009 13:04:43 +0000]
ath9k: Storage class should be before const qualifier

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agocfg80211: fix race between deauth and assoc response
Johannes Berg [Wed, 23 Dec 2009 12:12:05 +0000]
cfg80211: fix race between deauth and assoc response

Joseph Nahmias reported, in http://bugs.debian.org/562016,
that he was getting the following warning (with some log
around the issue):

  ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
  ath0: direct probe responded
  ath0: authenticate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: authenticated
  ath0: associate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: deauthenticating from 00:11:95:77:e0:b0 by local choice (reason=3)
  ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
  ath0: RX AssocResp from 00:11:95:77:e0:b0 (capab=0x421 status=0 aid=2)
  ath0: associated
  ------------[ cut here ]------------
  WARNING: at net/wireless/mlme.c:97 cfg80211_send_rx_assoc+0x14d/0x152 [cfg80211]()
  Hardware name: 7658CTO
  ...
  Pid: 761, comm: phy0 Not tainted 2.6.32-trunk-686 #1
  Call Trace:
   [<c1030a5d>] ? warn_slowpath_common+0x5e/0x8a
   [<c1030a93>] ? warn_slowpath_null+0xa/0xc
   [<f86cafc7>] ? cfg80211_send_rx_assoc+0x14d/0x152
  ...
  ath0: link becomes ready
  ath0: deauthenticating from 00:11:95:77:e0:b0 by local choice (reason=3)
  ath0: no IPv6 routers present
  ath0: link is not ready
  ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
  ath0: direct probe responded
  ath0: authenticate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: authenticated
  ath0: associate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: RX ReassocResp from 00:11:95:77:e0:b0 (capab=0x421 status=0 aid=2)
  ath0: associated

It is not clear to me how the first "direct probe" here
happens, but this seems to be a race condition, if the
user requests to deauth after requesting assoc, but before
the assoc response is received. In that case, it may
happen that mac80211 tries to report the assoc success to
cfg80211, but gets blocked on the wdev lock that is held
because the user is requesting the deauth.

The result is that we run into a warning. This is mostly
harmless, but maybe cause an unexpected event to be sent
to userspace; we'd send an assoc success event although
userspace was no longer expecting that.

To fix this, remove the warning and check whether the
race happened and in that case abort processing.

Reported-by: Joseph Nahmias <joe@nahmias.net>
Cc: stable@kernel.org
Cc: 562016-quiet@bugs.debian.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agowireless: remove remaining qual code
Johannes Berg [Wed, 23 Dec 2009 12:12:04 +0000]
wireless: remove remaining qual code

This removes the remaining users of the rx status
'qual' field and the field itself.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agort2x00: Add USB ID for Linksys WUSB 600N rev 2.
Gertjan van Wingerde [Tue, 22 Dec 2009 23:03:21 +0000]
rt2x00: Add USB ID for Linksys WUSB 600N rev 2.

This is a rt2870 based device.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath5k: fix SWI calibration interrupt storm
Bob Copeland [Tue, 22 Dec 2009 03:26:48 +0000]
ath5k: fix SWI calibration interrupt storm

The calibration period is now invoked by triggering a software
interrupt from within the ISR by ath5k_hw_calibration_poll()
instead of via a timer.

However, the calibration interval isn't initialized before
interrupts are enabled, so we can have a situation where an
interrupt occurs before the interval is assigned, so the
interval is actually negative.  As a result, the ISR will
arm a software interrupt to schedule the tasklet, and then
rearm it when the SWI is processed, and so on, leading to a
softlockup at modprobe time.

Move the initialization order around so the calibration interval
is set before interrupts are active.  Another possible fix
is to schedule the tasklet directly from the poll routine,
but I think there are additional plans for the SWI.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: fix ibss join with fixed-bssid
Felix Fietkau [Sun, 20 Dec 2009 18:07:09 +0000]
mac80211: fix ibss join with fixed-bssid

When fixed bssid is requested when joining an ibss network, incoming
beacons that match the configured bssid cause mac80211 to create new
sta entries, even before the ibss interface is in joined state.
When that happens, it fails to bring up the interface entirely, because
it checks for existing sta entries before joining.
This patch fixes this bug by refusing to create sta info entries before
the interface is fully operational.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>