8 years agoBluetooth: l2cap: Fix lost wakeups waiting to accept socket
Peter Hurley [Sun, 24 Jul 2011 04:10:52 +0000]
Bluetooth: l2cap: Fix lost wakeups waiting to accept socket

Fix race conditions which can cause lost wakeups (or misssed signals)
while waiting to accept an l2cap socket connection.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

8 years agoBluetooth: Fix lost wakeups waiting for sock state change
Peter Hurley [Sun, 24 Jul 2011 04:10:46 +0000]
Bluetooth: Fix lost wakeups waiting for sock state change

Fix race conditions which can cause lost wakeups while waiting
for sock state to change.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

8 years agoBluetooth: rfcomm: Fix lost wakeups waiting to accept socket
Peter Hurley [Sun, 24 Jul 2011 04:10:41 +0000]
Bluetooth: rfcomm: Fix lost wakeups waiting to accept socket

Fix race conditions which can cause lost wakeups (or missed
signals) while waiting to accept an rfcomm socket connection.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

8 years agoBluetooth: rfcomm: Remove unnecessary krfcommd event
Peter Hurley [Sun, 24 Jul 2011 04:10:35 +0000]
Bluetooth: rfcomm: Remove unnecessary krfcommd event

Removed superfluous event handling which was used to signal
that the rfcomm kthread had been woken. This appears to have been
used to prevent lost wakeups. Correctly ordering when the task
state is set to TASK_INTERRUPTIBLE is sufficient to prevent lost wakeups.

To prevent wakeups which occurred prior to initially setting
TASK_INTERRUPTIBLE from being lost, the main work of the thread loop -
rfcomm_process_sessions() - is performed prior to sleeping.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

8 years agoBluetooth: Add Toshiba laptops AR30XX device ID
Ricardo Mendoza [Wed, 13 Jul 2011 15:04:29 +0000]
Bluetooth: Add Toshiba laptops AR30XX device ID

Blacklist Toshiba-branded AR3011 based AR5B195 [0930:0215] and add to
ath3k.c for firmware loading.

Signed-off-by: Ricardo Mendoza <ricmm@gentoo.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

8 years agoBluetooth: btusb: be quiet on device disconnect
Paul Bolle [Tue, 9 Aug 2011 15:16:28 +0000]
Bluetooth: btusb: be quiet on device disconnect

Disabling the bluetooth usb device embedded in (some) ThinkPads tends to
lead to errors like these:
    btusb_bulk_complete: hci0 urb ffff88011b9bfd68 failed to resubmit (19)
    btusb_intr_complete: hci0 urb ffff88011b46a318 failed to resubmit (19)
    btusb_bulk_complete: hci0 urb ffff88011b46a000 failed to resubmit (19)

That is because usb_disconnect() doesn't "quiesces" pending urbs.

Disconnecting a device is a normal thing to happen so it's no big deal
that usb_submit_urb() returns -ENODEV. The simplest way to get rid of
these errors is to stop treating that return as an error. Trivial,
actually.

While we're at it, add comments to be explicit about the reasons we're
not complaining about -EPERM and -ENODEV.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

8 years agoBluetooth: unlock if allocation fails in hci_blacklist_add()
Dan Carpenter [Wed, 3 Aug 2011 14:22:45 +0000]
Bluetooth: unlock if allocation fails in hci_blacklist_add()

There was a small typo here so we never actually hit the goto which
would call hci_dev_unlock_bh().

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

8 years agort2x00: fix crash in rt2800usb_get_txwi
Stanislaw Gruszka [Wed, 10 Aug 2011 13:32:24 +0000]
rt2x00: fix crash in rt2800usb_get_txwi

Patch should fix this oops:

BUG: unable to handle kernel NULL pointer dereference at 000000a0
IP: [<f81b30c9>] rt2800usb_get_txwi+0x19/0x70 [rt2800usb]
*pdpt = 0000000000000000 *pde = f000ff53f000ff53
Oops: 0000 [#1] SMP
Pid: 198, comm: kworker/u:3 Tainted: G        W   3.0.0-wl+ #9 LENOVO 6369CTO/6369CTO
EIP: 0060:[<f81b30c9>] EFLAGS: 00010283 CPU: 1
EIP is at rt2800usb_get_txwi+0x19/0x70 [rt2800usb]
EAX: 00000000 EBX: f465e140 ECX: f4494960 EDX: ef24c5f8
ESI: 810f21f5 EDI: f1da9960 EBP: f4581e80 ESP: f4581e70
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process kworker/u:3 (pid: 198, ti=f4580000 task=f4494960 task.ti=f4580000)
Call Trace:
 [<f804790f>] rt2800_txdone_entry+0x2f/0xf0 [rt2800lib]
 [<c045110d>] ? warn_slowpath_common+0x7d/0xa0
 [<f81b3a38>] ? rt2800usb_work_txdone+0x288/0x360 [rt2800usb]
 [<f81b3a38>] ? rt2800usb_work_txdone+0x288/0x360 [rt2800usb]
 [<f81b3a13>] rt2800usb_work_txdone+0x263/0x360 [rt2800usb]
 [<c046a8d6>] process_one_work+0x186/0x440
 [<c046a85a>] ? process_one_work+0x10a/0x440
 [<f81b37b0>] ? rt2800usb_probe_hw+0x120/0x120 [rt2800usb]
 [<c046c283>] worker_thread+0x133/0x310
 [<c04885db>] ? trace_hardirqs_on+0xb/0x10
 [<c046c150>] ? manage_workers+0x1e0/0x1e0
 [<c047054c>] kthread+0x7c/0x90
 [<c04704d0>] ? __init_kthread_worker+0x60/0x60
 [<c0826b42>] kernel_thread_helper+0x6/0x1

Oops might happen because we check rt2x00queue_empty(queue) twice,
but this condition can change and we can process entry in
rt2800_txdone_entry(), which was already processed by
rt2800usb_txdone_entry_check() -> rt2x00lib_txdone_noinfo() and
has nullify entry->skb .

Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agort2x00: fix order of entry flags modification
Stanislaw Gruszka [Wed, 10 Aug 2011 13:32:23 +0000]
rt2x00: fix order of entry flags modification

In rt2800usb_work_txdone we check flags in order:

- ENTRY_OWNER_DEVICE_DATA
- ENTRY_DATA_STATUS_PENDING
- ENTRY_DATA_IO_FAILED

Modify flags in separate order in rt2x00usb_interrupt_txdone, to avoid
processing entries in _txdone with wrong flags or skip processing
ready entries.

Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agort2x00: fix crash in rt2800usb_write_tx_desc
Stanislaw Gruszka [Wed, 10 Aug 2011 13:32:22 +0000]
rt2x00: fix crash in rt2800usb_write_tx_desc

Patch should fix this oops:

BUG: unable to handle kernel NULL pointer dereference at 000000a0
IP: [<f8e06078>] rt2800usb_write_tx_desc+0x18/0xc0 [rt2800usb]
*pdpt = 000000002408c001 *pde = 0000000024079067 *pte = 0000000000000000
Oops: 0000 [#1] SMP
EIP: 0060:[<f8e06078>] EFLAGS: 00010282 CPU: 0
EIP is at rt2800usb_write_tx_desc+0x18/0xc0 [rt2800usb]
EAX: 00000035 EBX: ef2bef10 ECX: 00000000 EDX: d40958a0
ESI: ef1865f8 EDI: ef1865f8 EBP: d4095878 ESP: d409585c
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Call Trace:
 [<f8da5e85>] rt2x00queue_write_tx_frame+0x155/0x300 [rt2x00lib]
 [<f8da424c>] rt2x00mac_tx+0x7c/0x370 [rt2x00lib]
 [<c04882b2>] ? mark_held_locks+0x62/0x90
 [<c081f645>] ? _raw_spin_unlock_irqrestore+0x35/0x60
 [<c04884ba>] ? trace_hardirqs_on_caller+0x5a/0x170
 [<c04885db>] ? trace_hardirqs_on+0xb/0x10
 [<f8d618ac>] __ieee80211_tx+0x5c/0x1e0 [mac80211]
 [<f8d631fc>] ieee80211_tx+0xbc/0xe0 [mac80211]
 [<f8d63163>] ? ieee80211_tx+0x23/0xe0 [mac80211]
 [<f8d632e1>] ieee80211_xmit+0xc1/0x200 [mac80211]
 [<f8d63220>] ? ieee80211_tx+0xe0/0xe0 [mac80211]
 [<c0487d45>] ? lock_release_holdtime+0x35/0x1b0
 [<f8d63986>] ? ieee80211_subif_start_xmit+0x446/0x5f0 [mac80211]
 [<f8d637dd>] ieee80211_subif_start_xmit+0x29d/0x5f0 [mac80211]
 [<f8d63924>] ? ieee80211_subif_start_xmit+0x3e4/0x5f0 [mac80211]
 [<c0760188>] ? sock_setsockopt+0x6a8/0x6f0
 [<c0760000>] ? sock_setsockopt+0x520/0x6f0
 [<c076daef>] dev_hard_start_xmit+0x2ef/0x650

Oops might happen because we perform parallel putting new entries in a
queue (rt2x00queue_write_tx_frame()) and removing entries after
finishing transmitting (rt2800usb_work_txdone()). There are cases when
_txdone may process an entry that was not fully send and nullify
entry->skb .

To fix check in _txdone if entry has flags that indicate pending
transmission and wait until flags get cleared.

Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agodrivers/net/wireless/wl1251: add missing kfree
Julia Lawall [Mon, 8 Aug 2011 11:18:03 +0000]
drivers/net/wireless/wl1251: add missing kfree

In each case, the kfree already at the end of the function is also needed
in the error case.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@

x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...kfree(x)...+> }
     when any
     when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
               when forall
(
 return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoath5k: fix error handling in ath5k_beacon_send
Bob Copeland [Sun, 7 Aug 2011 23:36:07 +0000]
ath5k: fix error handling in ath5k_beacon_send

This cleans up error handling for the beacon in case of dma mapping
failure.  We need to free the skb when dma mapping fails instead of
nulling and leaking the pointer, and we should bail out to avoid
giving the hardware the bad descriptor.

Finally, we need to perform the null check after trying to update
the beacon, or else beacons will never be sent after a single
mapping failure.

Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agort2x00: Add rt2870 device id for Dvico usb key
Anthony Bourguignon [Fri, 5 Aug 2011 05:46:32 +0000]
rt2x00: Add rt2870 device id for Dvico usb key

This patch add a device id for the wifi usb keys shiped by DVICO with
some of their tvix hardware.

Signed-off-by: Anthony Bourguignon <contact+kernel@toniob.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoath9k: fix a misprint which leads to incorrect calibration
Alex Hacker [Thu, 4 Aug 2011 07:47:32 +0000]
ath9k: fix a misprint which leads to incorrect calibration

This patch addresses an issue with incorrect HW register
AR_PHY_TX_IQCAL_CORR_COEFF_B1 definition which leads to incorrect clibration.

Cc: stable@kernel.org
Signed-off-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agort2x00: Add new rt73 buffalo USB id
Ivo van Doorn [Wed, 3 Aug 2011 19:09:49 +0000]
rt2x00: Add new rt73 buffalo USB id

Reported-by: Maik-Holger Freudenberg <hhfeuer@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agortlwifi: rtl892cu: New USB IDs
Larry Finger [Tue, 2 Aug 2011 21:52:33 +0000]
rtlwifi: rtl892cu: New USB IDs

This patch fixes several problems in the USB_DEVICE table, including missing IDs,
reversed vendor/product codes, and a duplicate ID.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoath9k_hw: update PMU to improve ripple issue for AR9485
Rajkumar Manoharan [Fri, 29 Jul 2011 12:08:17 +0000]
ath9k_hw: update PMU to improve ripple issue for AR9485

The commit ebefce3d13f8b5a871337ff7c3821ee140c1ea8a failed
to set proper PMU value to address ripple issue for AR9485.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoath9k_hw: Fix incorrect Tx control power in AR9003 template
Rajkumar Manoharan [Fri, 29 Jul 2011 12:08:15 +0000]
ath9k_hw: Fix incorrect Tx control power in AR9003 template

CTL power data incorrect in ctlPowerData_2G field of ar9300_eeprom.
Setting incorrect CTL power in calibration is causing lower tx power.
Tx power was reported as 3dBm while operating in channel 6 HT40+/
in channel 11 HT40- due to CTL powers in the calibration is set to
zero.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agob43: read correct register on bcma bus.
Hauke Mehrtens [Sat, 23 Jul 2011 11:57:33 +0000]
b43: read correct register on bcma bus.

This causes an databus error on a Broadcom SoC using bcma.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for...
John W. Linville [Wed, 3 Aug 2011 13:18:21 +0000]
Merge git://git./linux/kernel/git/linville/wireless-next into for-davem

8 years agoiwlagn: 5000 do not support idle mode
Wey-Yi Guy [Tue, 2 Aug 2011 16:08:37 +0000]
iwlagn: 5000 do not support idle mode

5000 series has issue supporting power save idle mode:

commit 9dc2153315650eae220898668b6aa56a25c130be

iwlwifi: always support idle mode for agn devices

For agn devices, always support idle mode which help power
consumption in idle unassociated state.

the above changes cause 5000 become not stable when power management is "on"

http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2312

Cc: stable@kernel.org #2.6.39, #3.0.0
Reported-by: Devin J Pohly <djpohly+iwl@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agort2x00: fix usage of NULL queue
Stanislaw Gruszka [Tue, 2 Aug 2011 11:29:02 +0000]
rt2x00: fix usage of NULL queue

We may call rt2x00queue_pause_queue(queue) with queue == NULL. Bug
was introduced by commit 62fe778412b36791b7897cfa139342906fbbf07b
"rt2x00: Fix stuck queue in tx failure case" .

Cc: stable@kernel.org # 3.0+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agort2x00: Fix compilation without CONFIG_RT2X00_LIB_CRYPTO
Helmut Schaa [Tue, 2 Aug 2011 09:43:14 +0000]
rt2x00: Fix compilation without CONFIG_RT2X00_LIB_CRYPTO

This was introduced by commit
77b5621bac4a56b83b9081f48d4e7d1accdde400 (rt2x00: Don't use queue entry
as parameter when creating TX descriptor.)

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoiwlagn: sysfs couldn't find the priv pointer
Emmanuel Grumbach [Mon, 1 Aug 2011 19:46:57 +0000]
iwlagn: sysfs couldn't find the priv pointer

This bug has been introduced by:
d593411084a56124aa9d80aafa15db8463b2d8f7
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date:   Mon Jul 11 10:48:51 2011 +0300

    iwlagn: simplify the bus architecture

Revert part of the buggy patch: dev_get_drvdata will now return
iwl_priv as it did before the patch.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agort2x00: rt2800: fix zeroing skb structure
Stanislaw Gruszka [Sat, 30 Jul 2011 11:32:56 +0000]
rt2x00: rt2800: fix zeroing skb structure

We should clear skb->data not skb itself. Bug was introduced by:
commit 0b8004aa12d13ec750d102ba4082a95f0107c649 "rt2x00: Properly
reserve room for descriptors in skbs".

Cc: stable@kernel.org # 2.6.36+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agortlwifi: Fix kernel oops on ARM SOC
Larry Finger [Fri, 29 Jul 2011 15:53:12 +0000]
rtlwifi: Fix kernel oops on ARM SOC

This driver uses information from the self member of the pci_bus struct to
get information regarding the bridge to which the PCIe device is attached.
Unfortunately, this member is not established on all architectures, which
leads to a kernel oops.

Skipping the entire block that uses the self member to determine the bridge
vendor will only affect RTL8192DE devices as that driver sets the ASPM support
flag differently when the bridge vendor is Intel. If the self member is
available, there is no functional change.

This patch fixes Bugzilla No. 40212.

Reported-by: Hubert Liao <liao.hubertt@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [back to 2.6.38]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoath9k: skip ->config_pci_powersave() if PCIe port has ASPM disabled
Stanislaw Gruszka [Fri, 29 Jul 2011 13:59:08 +0000]
ath9k: skip ->config_pci_powersave() if PCIe port has ASPM disabled

We receive many bug reports about system hang during suspend/resume
when ath9k driver is in use. Adrian Chadd remarked that this problem
happens on systems that have ASPM disabled.

To do not hit the bug, skip doing ->config_pci_powersave magic if PCIe
downstream port device, which ath9k device is connected to, has ASPM
disabled.

Bug was introduced by:

commit 53bc7aa08b48e5cd745f986731cc7dc24eef2a9f
Author: Vivek Natarajan <vnatarajan@atheros.com>
Date:   Mon Apr 5 14:48:04 2010 +0530

    ath9k: Add support for newer AR9285 chipsets.

Patch should address:
https://bugzilla.kernel.org/show_bug.cgi?id=37462
https://bugzilla.kernel.org/show_bug.cgi?id=37082
https://bugzilla.redhat.com/show_bug.cgi?id=697157

however I did not receive confirmation about that, except from Camilo
Mesias, whose system stops hang regularly with this patch (but still
hangs from time to time, but this is probably some other bug).

Tested-by: Camilo Mesias <camilo@mesias.co.uk>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agocfg80211: off by one in nl80211_trigger_scan()
Dan Carpenter [Fri, 29 Jul 2011 08:52:18 +0000]
cfg80211: off by one in nl80211_trigger_scan()

The test is off by one so we'd read past the end of the
wiphy->bands[] array on the next line.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoiwlegacy: set tx power after rxon_assoc
Stanislaw Gruszka [Wed, 27 Jul 2011 13:37:43 +0000]
iwlegacy: set tx power after rxon_assoc

If settings of tx power was deferred during scan or changing channel we
have to setup them during commit rxon. Fix problem on 3945 (4965 already
has this fix).

Optimize code to apply tx settings only when tx power was actually
changed.

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoath9k: initialize tx chainmask before testing channel tx power values
Felix Fietkau [Wed, 27 Jul 2011 13:01:02 +0000]
ath9k: initialize tx chainmask before testing channel tx power values

With an uninitialized chainmask, the per-channel power will only contain
the power limits for a single chain instead of the combined tx power.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Linus Torvalds [Thu, 28 Jul 2011 12:58:19 +0000]
Merge git://git./linux/kernel/git/davem/net

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
  tg3: Remove 5719 jumbo frames and TSO blocks
  tg3: Break larger frags into 4k chunks for 5719
  tg3: Add tx BD budgeting code
  tg3: Consolidate code that calls tg3_tx_set_bd()
  tg3: Add partial fragment unmapping code
  tg3: Generalize tg3_skb_error_unmap()
  tg3: Remove short DMA check for 1st fragment
  tg3: Simplify tx bd assignments
  tg3: Reintroduce tg3_tx_ring_info
  ASIX: Use only 11 bits of header for data size
  ASIX: Simplify condition in rx_fixup()
  Fix cdc-phonet build
  bonding: reduce noise during init
  bonding: fix string comparison errors
  net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
  net: add IFF_SKB_TX_SHARED flag to priv_flags
  net: sock_sendmsg_nosec() is static
  forcedeth: fix vlans
  gianfar: fix bug caused by 87c288c6e9aa31720b72e2bc2d665e24e1653c3e
  gro: Only reset frag0 when skb can be pulled
  ...

8 years agoMerge branch 'for-linus' of git://neil.brown.name/md
Linus Torvalds [Thu, 28 Jul 2011 12:50:27 +0000]
Merge branch 'for-linus' of git://neil.brown.name/md

* 'for-linus' of git://neil.brown.name/md: (75 commits)
  md/raid10: handle further errors during fix_read_error better.
  md/raid10: Handle read errors during recovery better.
  md/raid10: simplify read error handling during recovery.
  md/raid10: record bad blocks due to write errors during resync/recovery.
  md/raid10:  attempt to fix read errors during resync/check
  md/raid10:  Handle write errors by updating badblock log.
  md/raid10: clear bad-block record when write succeeds.
  md/raid10: avoid writing to known bad blocks on known bad drives.
  md/raid10 record bad blocks as needed during recovery.
  md/raid10: avoid reading known bad blocks during resync/recovery.
  md/raid10 - avoid reading from known bad blocks - part 3
  md/raid10: avoid reading from known bad blocks - part 2
  md/raid10: avoid reading from known bad blocks - part 1
  md/raid10: Split handle_read_error out from raid10d.
  md/raid10: simplify/reindent some loops.
  md/raid5: Clear bad blocks on successful write.
  md/raid5.  Don't write to known bad block on doubtful devices.
  md/raid5: write errors should be recorded as bad blocks if possible.
  md/raid5: use bad-block log to improve handling of uncorrectable read errors.
  md/raid5: avoid reading from known bad blocks.
  ...

8 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
Linus Torvalds [Thu, 28 Jul 2011 12:49:31 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  sound: oss: rename local change_bits to avoid powerpc bitsops.h definition
  ALSA: hda - Fix duplicated DAC assignments for Realtek
  ALSA: asihpi - off by one in asihpi_hpi_ioctl()
  ALSA: hda - Fix Oops with Realtek quirks with NULL adc_nids
  ALSA: asihpi - bug fix pa use before init.
  ALSA: hda - Add support for vref-out based mute LED control on IDT codecs

8 years agotg3: Remove 5719 jumbo frames and TSO blocks
Matt Carlson [Wed, 27 Jul 2011 14:20:54 +0000]
tg3: Remove 5719 jumbo frames and TSO blocks

The A0 revision of this chip is the only device that requires these
features to be disabled.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agotg3: Break larger frags into 4k chunks for 5719
Matt Carlson [Wed, 27 Jul 2011 14:20:53 +0000]
tg3: Break larger frags into 4k chunks for 5719

The 5719 has bug where RDMAs larger than 4k can cause problems.  This
patch works around the problem by dividing larger DMA requests into
something the hardware can handle.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agotg3: Add tx BD budgeting code
Matt Carlson [Wed, 27 Jul 2011 14:20:52 +0000]
tg3: Add tx BD budgeting code

As the driver breaks large skb fragments into smaller submissions to the
hardware, there is a new danger that BDs might get exhausted before all
fragments have been mapped.  This patch adds code to make sure tx BDs
aren't oversubscribed and flag the condition if it happens.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agotg3: Consolidate code that calls tg3_tx_set_bd()
Matt Carlson [Wed, 27 Jul 2011 14:20:51 +0000]
tg3: Consolidate code that calls tg3_tx_set_bd()

This patch consolidates all code that populates tx BDs into a single
routine.  Setting tx BDs needs to be more carefully controlled to see if
workarounds need to be applied.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agotg3: Add partial fragment unmapping code
Matt Carlson [Wed, 27 Jul 2011 14:20:50 +0000]
tg3: Add partial fragment unmapping code

The following patches are going to break skb fragments into smaller
sizes.  This patch attempts to make the change easier to digest by only
addressing the skb teardown portion.

The patch modifies the driver to skip over any BDs that have a flag set
that indicates the BD isn't the beginning of an skb fragment.  Such BDs
were a result of segmentation and do not need a pci_unmap_page() call.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agotg3: Generalize tg3_skb_error_unmap()
Matt Carlson [Wed, 27 Jul 2011 14:20:49 +0000]
tg3: Generalize tg3_skb_error_unmap()

In the following patches, unmapping skb fragments will get just as
complicated as mapping them.  This patch generalizes
tg3_skb_error_unmap() and makes it the one-stop-shop for skb unmapping.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agotg3: Remove short DMA check for 1st fragment
Matt Carlson [Wed, 27 Jul 2011 14:20:48 +0000]
tg3: Remove short DMA check for 1st fragment

The first fragment of an skb should always be greater than 8 bytes.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agotg3: Simplify tx bd assignments
Matt Carlson [Wed, 27 Jul 2011 14:20:47 +0000]
tg3: Simplify tx bd assignments

In the following patches, the process the driver will use to assign skb
fragments to transmit BDs will get more complicated.  To prepare for
that new code, this patch seeks to simplify how transmit BDs are
populated.  It does this by separating the code that assigns the BD
members from the logic that controls how the fields are set.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agotg3: Reintroduce tg3_tx_ring_info
Matt Carlson [Wed, 27 Jul 2011 14:20:46 +0000]
tg3: Reintroduce tg3_tx_ring_info

The following patches will require the use of an additional flag in the
ring_info structure.  The use of this flag is tx path specific, so this
patch defines a specialized ring_info structure.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoASIX: Use only 11 bits of header for data size
Marek Vasut [Tue, 26 Jul 2011 16:44:47 +0000]
ASIX: Use only 11 bits of header for data size

The AX88772B uses only 11 bits of the header for the actual size. The other bits
are used for something else. This causes dmesg full of messages:

asix_rx_fixup() Bad Header Length

This patch trims the check to only 11 bits. I believe on older chips, the
remaining 5 top bits are unused.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoASIX: Simplify condition in rx_fixup()
Marek Vasut [Tue, 26 Jul 2011 16:44:46 +0000]
ASIX: Simplify condition in rx_fixup()

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoFix cdc-phonet build
Chris Clayton [Tue, 26 Jul 2011 12:20:22 +0000]
Fix cdc-phonet build

Try to send to correct address this time!

----------  Forwarded Message  ----------

Subject: [PATCH] Fix cdc-phonet build
Date: Saturday 23 Jul 2011
From: Chris Clayton <chris2553@googlemail.com>
To: linux-net@vger.kernel.org

cdc-phonet does not presently build on linux-3.0 because there is no entry for it in
drivers/net/Makefile. This patch adds that entry.

Signed-off-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agobonding: reduce noise during init
Andy Gospodarek [Wed, 27 Jul 2011 10:09:26 +0000]
bonding: reduce noise during init

On Tue, Jul 26, 2011 at 05:40:27PM -0700, Joe Perches wrote:
> On Tue, 2011-07-26 at 17:37 -0700, Jay Vosburgh wrote:
> > Joe Perches <joe@perches.com> wrote:
> > >I'd prefer you don't separate the format string
> > >into multiple pieces.
> > Why not?  To me, it looks easier to read split into sections
> > that don't wrap lines.
>
> Harder to grep for a dmesg and the
> defect rate of these split formats is
> typically higher than single strings
> because of bad spacing between string
> segments.
>

I noticed that you took some time back in late 2009 to 'consolidate' the
split format-strings present in the bonding driver at the time and I've
decided I'm fine to leave them the way they are.  The main point of my
patch was to change the output and I would like to get that included.
Here is my updated patch...

Subject: [PATCH net-next-2.6 v2] bonding: reduce noise during init

Many are using sysfs to configure bonding rather than module options, so
there is no need for bonding to throw this warning in normal cases.

Keep the message around when debugging is enabled as it might be useful
for someone desperate enough to enable debugging, but eliminate it
otherwise.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agobonding: fix string comparison errors
Andy Gospodarek [Tue, 26 Jul 2011 11:12:27 +0000]
bonding: fix string comparison errors

When a bond contains a device where one name is the subset of another
(eth1 and eth10, for example), one cannot properly set the primary
device or the currently active device.

This was reported and based on work by Takuma Umeya.  I also verified
the problem and tested that this fix resolves it.

V2: A few did not like the the current code or my changes, so I
refactored bonding_store_primary and bonding_store_active_slave to be a
bit cleaner, dropped the use of strnicmp since we did not really need
the comparison to be case insensitive, and formatted the input string
from sysfs so a comparison to IFNAMSIZ could be used.

I also discovered an error in bonding_store_active_slave that would
modify bond->primary_slave rather than bond->curr_active_slave before
forcing the bonding driver to choose a new active slave.

V3: Actually sending the proper patch....

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Takuma Umeya <tumeya@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
Neil Horman [Tue, 26 Jul 2011 06:05:38 +0000]
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared

After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs.  There are a handful of drivers that violate this assumption of
course, and need to be fixed up.  This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet: add IFF_SKB_TX_SHARED flag to priv_flags
Neil Horman [Tue, 26 Jul 2011 06:05:37 +0000]
net: add IFF_SKB_TX_SHARED flag to priv_flags

Pktgen attempts to transmit shared skbs to net devices, which can't be used by
some drivers as they keep state information in skbs.  This patch adds a flag
marking drivers as being able to handle shared skbs in their tx path.  Drivers
are defaulted to being unable to do so, but calling ether_setup enables this
flag, as 90% of the drivers calling ether_setup touch real hardware and can
handle shared skbs.  A subsequent patch will audit drivers to ensure that the
flag is set properly

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Jiri Pirko <jpirko@redhat.com>
CC: Robert Olsson <robert.olsson@its.uu.se>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Alexey Dobriyan <adobriyan@gmail.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet: sock_sendmsg_nosec() is static
Eric Dumazet [Tue, 26 Jul 2011 02:39:41 +0000]
net: sock_sendmsg_nosec() is static

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoforcedeth: fix vlans
Jiri Pirko [Tue, 26 Jul 2011 10:19:28 +0000]
forcedeth: fix vlans

For some reason, when rxaccel is disabled, NV_RX3_VLAN_TAG_PRESENT is
still set and some pseudorandom vids appear. So check for
NETIF_F_HW_VLAN_RX as well. Also set correctly hw_features and set vlan
mode on probe.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agogianfar: fix bug caused by 87c288c6e9aa31720b72e2bc2d665e24e1653c3e
Sebastian Pöhn [Tue, 26 Jul 2011 00:03:13 +0000]
gianfar: fix bug caused by 87c288c6e9aa31720b72e2bc2d665e24e1653c3e

commit 87c288c6e9aa31720b72e2bc2d665e24e1653c3e "gianfar: do vlan cleanup" has two issues:
# permutation of rx and tx flags
# enabling vlan tag insertion by default (this leads to unusable connections on some configurations)

If VLAN insertion is requested (via ethtool) it will be set at an other point ...

Signed-off-by: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoMerge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville...
David S. Miller [Thu, 28 Jul 2011 05:18:47 +0000]
Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless-next-2.6

8 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris...
Linus Torvalds [Thu, 28 Jul 2011 02:26:38 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (54 commits)
  tpm_nsc: Fix bug when loading multiple TPM drivers
  tpm: Move tpm_tis_reenable_interrupts out of CONFIG_PNP block
  tpm: Fix compilation warning when CONFIG_PNP is not defined
  TOMOYO: Update kernel-doc.
  tpm: Fix a typo
  tpm_tis: Probing function for Intel iTPM bug
  tpm_tis: Fix the probing for interrupts
  tpm_tis: Delay ACPI S3 suspend while the TPM is busy
  tpm_tis: Re-enable interrupts upon (S3) resume
  tpm: Fix display of data in pubek sysfs entry
  tpm_tis: Add timeouts sysfs entry
  tpm: Adjust interface timeouts if they are too small
  tpm: Use interface timeouts returned from the TPM
  tpm_tis: Introduce durations sysfs entry
  tpm: Adjust the durations if they are too small
  tpm: Use durations returned from TPM
  TOMOYO: Enable conditional ACL.
  TOMOYO: Allow using argv[]/envp[] of execve() as conditions.
  TOMOYO: Allow using executable's realpath and symlink's target as conditions.
  TOMOYO: Allow using owner/group etc. of file objects as conditions.
  ...

Fix up trivial conflict in security/tomoyo/realpath.c

8 years agomd/raid10: handle further errors during fix_read_error better.
NeilBrown [Thu, 28 Jul 2011 01:39:25 +0000]
md/raid10: handle further errors during fix_read_error better.

If we find more read/write errors we should record a bad block before
failing the device.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10: Handle read errors during recovery better.
NeilBrown [Thu, 28 Jul 2011 01:39:25 +0000]
md/raid10: Handle read errors during recovery better.

Currently when we get a read error during recovery, we simply abort
the recovery.

Instead, repeat the read in page-sized blocks.
On successful reads, write to the target.
On read errors, record a bad block on the destination,
and only if that fails do we abort the recovery.

As we now retry reads we need to know where we read from.  This was in
bi_sector but that can be changed during a read attempt.
So store the correct from_addr and to_addr in the r10_bio for later
access.

Signed-off-by: NeilBrown<neilb@suse.de>

8 years agomd/raid10: simplify read error handling during recovery.
NeilBrown [Thu, 28 Jul 2011 01:39:25 +0000]
md/raid10: simplify read error handling during recovery.

If a read error is detected during recovery the code currently
fails the read device.
This isn't really necessary.  recovery_request_write will signal
a write error to end_sync_write and it will record a write
error on the destination device which will record a bad block
there or kick it from the array.

So just remove this call to do md_error.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10: record bad blocks due to write errors during resync/recovery.
NeilBrown [Thu, 28 Jul 2011 01:39:25 +0000]
md/raid10: record bad blocks due to write errors during resync/recovery.

If we get a write error during resync/recovery don't fail the device
but instead record a bad block.  If that fails we can then fail the
device.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10: attempt to fix read errors during resync/check
NeilBrown [Thu, 28 Jul 2011 01:39:25 +0000]
md/raid10:  attempt to fix read errors during resync/check

We already attempt to fix read errors found during normal IO
and a 'repair' process.
It is best to try to repair them at any time they are found,
so move a test so that during sync and check a read error will
be corrected by over-writing with good data.

If both (all) devices have known bad blocks in the sync section we
won't try to fix even though the bad blocks might not overlap.  That
should be considered later.

Also if we hit a read error during recovery we don't try to fix it.
It would only be possible to fix if there were at least three copies
of data, which is not very common with RAID10.  But it should still
be considered later.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10: Handle write errors by updating badblock log.
NeilBrown [Thu, 28 Jul 2011 01:39:24 +0000]
md/raid10:  Handle write errors by updating badblock log.

When we get a write error (in the data area, not in metadata),
update the badblock log rather than failing the whole device.

As the write may well be many blocks, we trying writing each
block individually and only log the ones which fail.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10: clear bad-block record when write succeeds.
NeilBrown [Thu, 28 Jul 2011 01:39:24 +0000]
md/raid10: clear bad-block record when write succeeds.

If we succeed in writing to a block that was recorded as
being bad, we clear the bad-block record.

This requires some delayed handling as the bad-block-list update has
to happen in process-context.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10: avoid writing to known bad blocks on known bad drives.
NeilBrown [Thu, 28 Jul 2011 01:39:24 +0000]
md/raid10: avoid writing to known bad blocks on known bad drives.

Writing to known bad blocks on drives that have seen a write error
is asking for trouble.  So try to avoid these blocks.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10 record bad blocks as needed during recovery.
NeilBrown [Thu, 28 Jul 2011 01:39:24 +0000]
md/raid10 record bad blocks as needed during recovery.

When recovering one or more devices, if all the good devices have
bad blocks we should record a bad block on the device being rebuilt.

If this fails, we need to abort the recovery.

To ensure we don't think that we aborted later than we actually did,
we need to move the check for MD_RECOVERY_INTR earlier in md_do_sync,
in particular before mddev->curr_resync is updated.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10: avoid reading known bad blocks during resync/recovery.
NeilBrown [Thu, 28 Jul 2011 01:39:24 +0000]
md/raid10: avoid reading known bad blocks during resync/recovery.

During resync/recovery limit the size of the request to avoid
reading into a bad block that does not start at-or-before the current
read address.

Similarly if there is a bad block at this address, don't allow the
current request to extend beyond the end of that bad block.

Now that we don't ever read from known bad blocks, it is safe to allow
devices with those blocks into the array.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10 - avoid reading from known bad blocks - part 3
NeilBrown [Thu, 28 Jul 2011 01:39:24 +0000]
md/raid10 - avoid reading from known bad blocks - part 3

When attempting to repair a read error, don't read from
devices with a known bad block.

As we are only reading PAGE_SIZE blocks, we don't try to
narrow down to smaller regions in the hope that only part of this
page is bad - it isn't worth the effort.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10: avoid reading from known bad blocks - part 2
NeilBrown [Thu, 28 Jul 2011 01:39:23 +0000]
md/raid10: avoid reading from known bad blocks - part 2

When redirecting a read error to a different device, we must
again avoid bad blocks and possibly split the request.

Spin_lock typo fixed thanks to Dan Carpenter <error27@gmail.com>

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10: avoid reading from known bad blocks - part 1
NeilBrown [Thu, 28 Jul 2011 01:39:23 +0000]
md/raid10: avoid reading from known bad blocks - part 1

This patch just covers the basic read path:
 1/ read_balance needs to check for badblocks, and return not only
    the chosen slot, but also how many good blocks are available
    there.
 2/ read submission must be ready to issue multiple reads to
    different devices as different bad blocks on different devices
    could mean that a single large read cannot be served by any one
    device, but can still be served by the array.
    This requires keeping count of the number of outstanding requests
    per bio.  This count is stored in 'bi_phys_segments'

On read error we currently just fail the request if another target
cannot handle the whole request.  Next patch refines that a bit.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10: Split handle_read_error out from raid10d.
NeilBrown [Thu, 28 Jul 2011 01:39:23 +0000]
md/raid10: Split handle_read_error out from raid10d.

raid10d() is too big and is about to get bigger, so split
handle_read_error() out as a separate function.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid10: simplify/reindent some loops.
NeilBrown [Thu, 28 Jul 2011 01:39:23 +0000]
md/raid10: simplify/reindent some loops.

When a loop ends with a large if, it can be neater to change the
if to invert the condition and just 'continue'.
Then the body of the if can be indented to a lower level.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid5: Clear bad blocks on successful write.
NeilBrown [Thu, 28 Jul 2011 01:39:23 +0000]
md/raid5: Clear bad blocks on successful write.

On a successful write to a known bad block, flag the sh
so that raid5d can remove the known bad block from the list.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid5. Don't write to known bad block on doubtful devices.
NeilBrown [Thu, 28 Jul 2011 01:39:22 +0000]
md/raid5.  Don't write to known bad block on doubtful devices.

If a device has seen write errors, don't write to any known
bad blocks on that device.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid5: write errors should be recorded as bad blocks if possible.
NeilBrown [Thu, 28 Jul 2011 01:39:22 +0000]
md/raid5: write errors should be recorded as bad blocks if possible.

When a write error is detected, don't mark the device as failed
immediately but rather record the fact for handle_stripe to deal with.

Handle_stripe then attempts to record a bad block.  Only if that fails
does the device get marked as faulty.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid5: use bad-block log to improve handling of uncorrectable read errors.
NeilBrown [Thu, 28 Jul 2011 01:39:22 +0000]
md/raid5: use bad-block log to improve handling of uncorrectable read errors.

If we get an uncorrectable read error - record a bad block rather than
failing the device.
And if these errors (which may be due to known bad blocks) cause
recovery to be impossible, record a bad block on the recovering
devices, or abort the recovery.

As we might abort a recovery without failing a device we need to teach
RAID5 about recovery_disabled handling.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid5: avoid reading from known bad blocks.
NeilBrown [Thu, 28 Jul 2011 01:39:22 +0000]
md/raid5: avoid reading from known bad blocks.

There are two times that we might read in raid5:
1/ when a read request fits within a chunk on a single
   working device.
   In this case, if there is any bad block in the range of
   the read, we simply fail the cache-bypass read and
   perform the read though the stripe cache.

2/ when reading into the stripe cache.  In this case we
   mark as failed any device which has a bad block in that
   strip (1 page wide).
   Note that we will both avoid reading and avoid writing.
   This is correct (as we will never read from the block, there
   is no point writing), but not optimal (as writing could 'fix'
   the error) - that will be addressed later.

If we have not seen any write errors on the device yet, we treat a bad
block like a recent read error.  This will encourage an attempt to fix
the read error which will either generate a write error, or will
ensure good data is stored there.  We don't yet forget the bad block
in that case.  That comes later.

Now that we honour bad blocks when reading we can allow devices with
bad blocks into the array.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid1: factor several functions out or raid1d()
NeilBrown [Thu, 28 Jul 2011 01:38:13 +0000]
md/raid1: factor several functions out or raid1d()

raid1d is too big with several deep branches.
So separate them out into their own functions.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>

8 years agomd/raid1: improve handling of read failure during recovery.
NeilBrown [Thu, 28 Jul 2011 01:33:42 +0000]
md/raid1: improve handling of read failure during recovery.

If we cannot read a block from anywhere during recovery, there is
now a better approach than just giving up.
We can record a bad block on each device and keep going - being
careful not to clear the bad block when a write succeeds as it might -
it will be a write of incorrect data.

We have now reached the state where - for raid1 - we only call
md_error if md_set_badblocks has failed.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>

8 years agomd/raid1: record badblocks found during resync etc.
NeilBrown [Thu, 28 Jul 2011 01:33:00 +0000]
md/raid1: record badblocks found during resync etc.

If we find a bad block while writing as part of resync/recovery we
need to report that back to raid1d which must record the bad block,
or fail the device.

Similarly when fixing a read error, a further error should just
record a bad block if possible rather than failing the device.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>

8 years agomd/raid1: Handle write errors by updating badblock log.
NeilBrown [Thu, 28 Jul 2011 01:32:41 +0000]
md/raid1:  Handle write errors by updating badblock log.

When we get a write error (in the data area, not in metadata),
update the badblock log rather than failing the whole device.

As the write may well be many blocks, we trying writing each
block individually and only log the ones which fail.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>

8 years agomd/raid1: store behind-write pages in bi_vecs.
NeilBrown [Thu, 28 Jul 2011 01:32:10 +0000]
md/raid1: store behind-write pages in bi_vecs.

When performing write-behind we allocate pages to store the data
during write.
Previously we just keep a list of pages.  Now we keep a list of
bi_vec which includes offset and size.
This means that the r1bio has complete information to create a new
bio which will be needed for retrying after write errors.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>

8 years agomd/raid1: clear bad-block record when write succeeds.
NeilBrown [Thu, 28 Jul 2011 01:31:49 +0000]
md/raid1: clear bad-block record when write succeeds.

If we succeed in writing to a block that was recorded as
being bad, we clear the bad-block record.

This requires some delayed handling as the bad-block-list update has
to happen in process-context.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>

8 years agomd/raid1: avoid writing to known-bad blocks on known-bad drives.
NeilBrown [Thu, 28 Jul 2011 01:31:48 +0000]
md/raid1: avoid writing to known-bad blocks on known-bad drives.

If we have seen any write error on a drive, then don't write to
any known-bad blocks on that drive.
If necessary, we divide the write request up into pieces just
like we do for reads, so each piece is either all written or
all not written to any given drive.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>

8 years agomd: update documentation for md/rdev/state sysfs interface
Namhyung Kim [Thu, 28 Jul 2011 01:31:48 +0000]
md: update documentation for md/rdev/state sysfs interface

Previous patches in the bad block series extended behavior of
rdev's 'state' interface but lacked documentation update.
Fix it.

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd: make it easier to wait for bad blocks to be acknowledged.
NeilBrown [Thu, 28 Jul 2011 01:31:48 +0000]
md: make it easier to wait for bad blocks to be acknowledged.

It is only safe to choose not to write to a bad block if that bad
block is safely recorded in metadata - i.e. if it has been
'acknowledged'.

If it hasn't we need to wait for the acknowledgement.

We support that using rdev->blocked wait and
md_wait_for_blocked_rdev by introducing a new device flag
'BlockedBadBlock'.

This flag is only advisory.
It is cleared whenever we acknowledge a bad block, so that a waiter
can re-check the particular bad blocks that it is interested it.

It should be set by a caller when they find they need to wait.
This (set after test) is inherently racy, but as
md_wait_for_blocked_rdev already has a timeout, losing the race will
have minimal impact.

When we clear "Blocked" was also clear "BlockedBadBlocks" incase it
was set incorrectly (see above race).

We also modify the way we manage 'Blocked' to fit better with the new
handling of 'BlockedBadBlocks' and to make it consistent between
externally managed and internally managed metadata.   This requires
that each raidXd loop checks if the metadata needs to be written and
triggers a write (md_check_recovery) if needed.  Otherwise a queued
write request might cause raidXd to wait for the metadata to write,
and only that thread can write it.

Before writing metadata, we set FaultRecorded for all devices that
are Faulty, then after writing the metadata we clear Blocked for any
device for which the Fault was certainly Recorded.

The 'faulty' device flag now appears in sysfs if the device is faulty
*or* it has unacknowledged bad blocks.  So user-space which does not
understand bad blocks can continue to function correctly.
User space which does, should not assume a device is faulty until it
sees the 'faulty' flag, and then sees the list of unacknowledged bad
blocks is empty.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd: add 'write_error' flag to component devices.
NeilBrown [Thu, 28 Jul 2011 01:31:48 +0000]
md: add 'write_error' flag to component devices.

If a device has ever seen a write error, we will want to handle
known-bad-blocks differently.
So create an appropriate state flag and export it via sysfs.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>

8 years agomd/raid1: avoid reading known bad blocks during resync
NeilBrown [Thu, 28 Jul 2011 01:31:48 +0000]
md/raid1: avoid reading known bad blocks during resync

When performing resync/etc, keep the size of the request
small enough that it doesn't overlap any known bad blocks.
Devices with badblocks at the start of the request are completely
excluded.
If there is nowhere to read from due to bad blocks, record
a bad block on each target device.

Now that we never read from known-bad-blocks we can allow devices with
known-bad-blocks into a RAID1.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/raid1: avoid reading from known bad blocks.
NeilBrown [Thu, 28 Jul 2011 01:31:48 +0000]
md/raid1: avoid reading from known bad blocks.

Now that we have a bad block list, we should not read from those
blocks.
There are several main parts to this:
  1/ read_balance needs to check for bad blocks, and return not only
     the chosen device, but also how many good blocks are available
     there.
  2/ fix_read_error needs to avoid trying to read from bad blocks.
  3/ read submission must be ready to issue multiple reads to
     different devices as different bad blocks on different devices
     could mean that a single large read cannot be served by any one
     device, but can still be served by the array.
     This requires keeping count of the number of outstanding requests
     per bio.  This count is stored in 'bi_phys_segments'
  4/ retrying a read needs to also be ready to submit a smaller read
     and queue another request for the rest.

This does not yet handle bad blocks when reading to perform resync,
recovery, or check.

'md_trim_bio' will also be used for RAID10, so put it in md.c and
export it.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd: Disable bad blocks and v0.90 metadata.
NeilBrown [Thu, 28 Jul 2011 01:31:47 +0000]
md: Disable bad blocks and v0.90 metadata.

v0.90 metadata cannot record bad blocks, so when loading metadata
for such a device, set shift to -1.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd: load/store badblock list from v1.x metadata
NeilBrown [Thu, 28 Jul 2011 01:31:47 +0000]
md: load/store badblock list from v1.x metadata

Space must have been allocated when array was created.
A feature flag is set when the badblock list is non-empty, to
ensure old kernels don't load and trust the whole device.

We only update the on-disk badblocklist when it has changed.
If the badblocklist (or other metadata) is stored on a bad block, we
don't cope very well.

If metadata has no room for bad block, flag bad-blocks as disabled,
and do the same for 0.90 metadata.

Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd: don't allow arrays to contain devices with bad blocks.
NeilBrown [Thu, 28 Jul 2011 01:31:47 +0000]
md: don't allow arrays to contain devices with bad blocks.

As no personality understand bad block lists yet, we must
reject any device that is known to contain bad blocks.
As the personalities get taught, these tests can be removed.

This only applies to raid1/raid5/raid10.
For linear/raid0/multipath/faulty the whole concept of bad blocks
doesn't mean anything so there is no point adding the checks.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>

8 years agomd: add documentation for bad block log
Namhyung Kim [Thu, 28 Jul 2011 01:31:47 +0000]
md: add documentation for bad block log

Previous patch in the bad block series added new sysfs interfaces
([unacknowledged_]bad_blocks) for each rdev without documentation.
Add it.

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>

8 years agomd/bad-block-log: add sysfs interface for accessing bad-block-log.
NeilBrown [Thu, 28 Jul 2011 01:31:47 +0000]
md/bad-block-log: add sysfs interface for accessing bad-block-log.

This can show the log (providing it fits in one page) and
allows bad blocks to be 'acknowledged' meaning that they
have safely been recorded in metadata.

Clearing bad blocks is not allowed via sysfs (except for
code testing).  A bad block can only be cleared when
a write to the block succeeds.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>

8 years agomd: beginnings of bad block management.
NeilBrown [Thu, 28 Jul 2011 01:31:46 +0000]
md: beginnings of bad block management.

This the first step in allowing md to track bad-blocks per-device so
that we can fail individual blocks rather than the whole device.

This patch just adds a data structure for recording bad blocks, with
routines to add, remove, search the list.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>

8 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs...
Linus Torvalds [Wed, 27 Jul 2011 23:43:52 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/btrfs-unstable

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: make sure reserve_metadata_bytes doesn't leak out strange errors
  Btrfs: use the commit_root for reading free_space_inode crcs
  Btrfs: reduce extent_state lock contention for metadata
  Btrfs: remove lockdep magic from btrfs_next_leaf
  Btrfs: make a lockdep class for each root
  Btrfs: switch the btrfs tree locks to reader/writer
  Btrfs: fix deadlock when throttling transactions
  Btrfs: stop using highmem for extent_buffers
  Btrfs: fix BUG_ON() caused by ENOSPC when relocating space
  Btrfs: tag pages for writeback in sync
  Btrfs: fix enospc problems with delalloc
  Btrfs: don't flush delalloc arbitrarily
  Btrfs: use find_or_create_page instead of grab_cache_page
  Btrfs: use a worker thread to do caching
  Btrfs: fix how we merge extent states and deal with cached states
  Btrfs: use the normal checksumming infrastructure for free space cache
  Btrfs: serialize flushers in reserve_metadata_bytes
  Btrfs: do transaction space reservation before joining the transaction
  Btrfs: try to only do one btrfs_search_slot in do_setxattr

8 years agomd: remove suspicious size_of()
NeilBrown [Wed, 27 Jul 2011 21:56:24 +0000]
md: remove suspicious size_of()

When calling bioset_create we pass the size of the front_pad as
   sizeof(mddev)
which looks suspicious as mddev is a pointer and so it looks like a
common mistake where
   sizeof(*mddev)
was intended.
The size is actually correct as we want to store a pointer in the
front padding of the bios created by the bioset, so make the intent
more explicit by using
   sizeof(mddev_t *)

Reported-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>

8 years agoMerge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
Linus Torvalds [Wed, 27 Jul 2011 20:41:51 +0000]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: optimize the negative xattr caching
  xfs: prevent against ioend livelocks in xfs_file_fsync
  xfs: flag all buffers as metadata
  xfs: encapsulate a block of debug code

8 years agoMerge branch 'nfs-for-3.1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Linus Torvalds [Wed, 27 Jul 2011 20:23:02 +0000]
Merge branch 'nfs-for-3.1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs

* 'nfs-for-3.1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (44 commits)
  NFSv4: Don't use the delegation->inode in nfs_mark_return_delegation()
  nfs: don't use d_move in nfs_async_rename_done
  RDMA: Increasing RPCRDMA_MAX_DATA_SEGS
  SUNRPC: Replace xprt->resend and xprt->sending with a priority queue
  SUNRPC: Allow caller of rpc_sleep_on() to select priority levels
  SUNRPC: Support dynamic slot allocation for TCP connections
  SUNRPC: Clean up the slot table allocation
  SUNRPC: Initalise the struct xprt upon allocation
  SUNRPC: Ensure that we grab the XPRT_LOCK before calling xprt_alloc_slot
  pnfs: simplify pnfs files module autoloading
  nfs: document nfsv4 sillyrename issues
  NFS: Convert nfs4_set_ds_client to EXPORT_SYMBOL_GPL
  SUNRPC: Convert the backchannel exports to EXPORT_SYMBOL_GPL
  SUNRPC: sunrpc should not explicitly depend on NFS config options
  NFS: Clean up - simplify the switch to read/write-through-MDS
  NFS: Move the pnfs write code into pnfs.c
  NFS: Move the pnfs read code into pnfs.c
  NFS: Allow the nfs_pageio_descriptor to signal that a re-coalesce is needed
  NFS: Use the nfs_pageio_descriptor->pg_bsize in the read/write request
  NFS: Cache rpc_ops in struct nfs_pageio_descriptor
  ...

8 years agoMerge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target...
Linus Torvalds [Wed, 27 Jul 2011 20:21:40 +0000]
Merge branch 'for-next' of git://git./linux/kernel/git/nab/target-pending

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: Convert to DIV_ROUND_UP_SECTOR_T usage for sectors / dev_max_sectors
  kernel.h: Add DIV_ROUND_UP_ULL and DIV_ROUND_UP_SECTOR_T macro usage
  iscsi-target: Add iSCSI fabric support for target v4.1
  iscsi: Add Serial Number Arithmetic LT and GT into iscsi_proto.h
  iscsi: Use struct scsi_lun in iscsi structs instead of u8[8]
  iscsi: Resolve iscsi_proto.h naming conflicts with drivers/target/iscsi

8 years agoMerge branch 'integration' into for-linus
Chris Mason [Wed, 27 Jul 2011 20:13:10 +0000]
Merge branch 'integration' into for-linus

8 years agoBtrfs: make sure reserve_metadata_bytes doesn't leak out strange errors
Chris Mason [Wed, 27 Jul 2011 19:57:44 +0000]
Btrfs: make sure reserve_metadata_bytes doesn't leak out strange errors

The btrfs transaction code will return any errors that come from
reserve_metadata_bytes.  We need to make sure we don't return funny
things like 1 or EAGAIN.

Signed-off-by: Chris Mason <chris.mason@oracle.com>

8 years agosignals: sys_ssetmask/sys_rt_sigsuspend should use set_current_blocked()
Oleg Nesterov [Wed, 27 Jul 2011 19:49:44 +0000]
signals: sys_ssetmask/sys_rt_sigsuspend should use set_current_blocked()

sys_ssetmask(), sys_rt_sigsuspend() and compat_sys_rt_sigsuspend()
change ->blocked directly.  This is not correct, see the changelog in
e6fa16ab "signal: sigprocmask() should do retarget_shared_pending()"

Change them to use set_current_blocked().

Another change is that now we are doing ->saved_sigmask = ->blocked
lockless, it doesn't make any sense to do this under ->siglock.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Matt Fleming <matt.fleming@linux.intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>