8 years agoNET: am79c961: fix assembler warnings
Russell King - ARM Linux [Fri, 10 Jun 2011 00:52:35 +0000]
NET: am79c961: fix assembler warnings

Fix:
/tmp/ccvoZ6h8.s: Assembler messages:
/tmp/ccvoZ6h8.s:284: Warning: register range not in ascending order
/tmp/ccvoZ6h8.s:881: Warning: register range not in ascending order
/tmp/ccvoZ6h8.s:1087: Warning: register range not in ascending order

by ensuring that we have temporary variables placed into specific
registers.  Reorder the code a bit to allow the resulting assembly
to be slightly more optimal.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoNET: am79c961: ensure multicast filter is correctly set at open
Russell King - ARM Linux [Fri, 10 Jun 2011 00:52:14 +0000]
NET: am79c961: ensure multicast filter is correctly set at open

We were clearing out the multicast filter whenever the interface was
upped, and not setting the mode bits correctly.  This can cause
problems if there are any multicast addresses already set at this
point, or if ALLMULTI was set.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoNET: am79c961: ensure asm() statements are marked volatile
Russell King - ARM Linux [Fri, 10 Jun 2011 00:51:54 +0000]
NET: am79c961: ensure asm() statements are marked volatile

Without this the compiler can (and does) optimize register reads away
from within loops, and other such optimizations.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoethtool.h: fix typos
Yegor Yefremov [Thu, 9 Jun 2011 22:05:48 +0000]
ethtool.h: fix typos

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoep93xx_eth: Update MAINTAINERS
H Hartley Sweeten [Thu, 9 Jun 2011 22:00:21 +0000]
ep93xx_eth: Update MAINTAINERS

Lennert stated that he has been short on time lately. Since I'm maintaining
the ep93xx core stuff, I'm willing to also take over maintaining the Ethernet
driver.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoipv4: Fix packet size calculation for raw IPsec packets in __ip_append_data
Steffen Klassert [Sun, 5 Jun 2011 20:48:47 +0000]
ipv4: Fix packet size calculation for raw IPsec packets in __ip_append_data

We assume that transhdrlen is positive on the first fragment
which is wrong for raw packets. So we don't add exthdrlen to the
packet size for raw packets. This leads to a reallocation on IPsec
because we have not enough headroom on the skb to place the IPsec
headers. This patch fixes this by adding exthdrlen to the packet
size whenever the send queue of the socket is empty. This issue was
introduced with git commit 1470ddf7 (inet: Remove explicit write
references to sk/inet in ip_append_data)

Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
John W. Linville [Thu, 9 Jun 2011 18:23:30 +0000]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6 into for-davem

8 years agonetpoll: prevent netpoll setup on slave devices
WANG Cong [Thu, 9 Jun 2011 07:28:13 +0000]
netpoll: prevent netpoll setup on slave devices

In commit 8d8fc29d02a33e4bd5f4fa47823c1fd386346093
(netpoll: disable netpoll when enslave a device), we automatically
disable netpoll when the underlying device is being enslaved,
we also need to prevent people from setuping netpoll on
devices that are already enslaved.

Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet: pmtu_expires fixes
Eric Dumazet [Wed, 8 Jun 2011 06:07:07 +0000]
net: pmtu_expires fixes

commit 2c8cec5c10bc (ipv4: Cache learned PMTU information in inetpeer)
added some racy peer->pmtu_expires accesses.

As its value can be changed by another cpu/thread, we should be more
careful, reading its value once.

Add peer_pmtu_expired() and peer_pmtu_cleaned() helpers

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agogianfar:localized filer table
Wu Jiajun-B06378 [Tue, 7 Jun 2011 21:46:51 +0000]
gianfar:localized filer table

Each eTSEC device should own localized filer table.

Signed-off-by: Jiajun Wu <b06378@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoiwlegacy: fix channel switch locking
Stanislaw Gruszka [Wed, 8 Jun 2011 13:26:31 +0000]
iwlegacy: fix channel switch locking

We use priv->mutex to avoid race conditions between chswitch_done()
and mac_channel_switch(), when marking channel switch in
progress. But chswitch_done() can be called in atomic context
from rx_csa() or with mutex already taken from commit_rxon().

To fix remove mutex from chswitch_done() and use atomic bitops
for marking channel switch pending.

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agomac80211: fix IBSS teardown race
Johannes Berg [Wed, 8 Jun 2011 11:27:29 +0000]
mac80211: fix IBSS teardown race

Ignacy reports that sometimes after leaving an IBSS
joining a new one didn't work because there still
were stations on the list. He fixed it by flushing
stations when attempting to join a new IBSS, but
this shouldn't be happening in the first case. When
I looked into it I saw a race condition in teardown
that could cause stations to be added after flush,
and thus cause this situation. Ignacy confirms that
after applying my patch he hasn't seen this happen
again.

Reported-by: Ignacy Gawedzki <i@lri.fr>
Debugged-by: Ignacy Gawedzki <i@lri.fr>
Tested-by: Ignacy Gawedzki <i@lri.fr>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoiwlagn: send tx power command if defer cause by RXON not match
Wey-Yi Guy [Fri, 27 May 2011 15:40:24 +0000]
iwlagn: send tx power command if defer cause by RXON not match

During channge channel, tx power will not send to uCode, the tx power command
should send after scan complete. but should also can send after RXON command.

Stable fix identified by Stanislaw Gruszka <sgruszka@redhat.com>.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoxfrm: Fix off by one in the replay advance functions
Steffen Klassert [Sun, 5 Jun 2011 20:46:03 +0000]
xfrm: Fix off by one in the replay advance functions

We may write 4 byte too much when we reinitialize the anti replay
window in the replay advance functions. This patch fixes this by
adjusting the last index of the initialization loop.

Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoigb: fix i350 SR-IOV failture
Williams, Mitch A [Tue, 7 Jun 2011 21:22:57 +0000]
igb: fix i350 SR-IOV failture

When SR-IOV is enabled, i350 devices fail to pass traffic. This is due to
the driver attempting to enable RSS on the PF device, which is not
supported by the i350.

When max_vfs is specified on an i350 adapter, set the number of RSS queues
to 1.

This issue affects 2.6.39 as well.

CC: stable@kernel.org
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonl80211: fix overflow in ssid_len
Luciano Coelho [Tue, 7 Jun 2011 17:42:26 +0000]
nl80211: fix overflow in ssid_len

When one of the SSID's length passed in a scan or sched_scan request
is larger than 255, there will be an overflow in the u8 that is used
to store the length before checking.  This causes the check to fail
and we overrun the buffer when copying the SSID.

Fix this by checking the nl80211 attribute length before copying it to
the struct.

This is a follow up for the previous commit
208c72f4fe44fe09577e7975ba0e7fa0278f3d03, which didn't fix the problem
entirely.

Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agortlwifi: Avoid modifying skbs that are resubmitted
Mike McCormack [Mon, 6 Jun 2011 23:58:31 +0000]
rtlwifi: Avoid modifying skbs that are resubmitted

In the case we fail to allocate a new skb, the old skb should
be resubmitted unmodified.

Fixes bug introduced in a9e12869758430424804.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agortlwifi: Fix logic in rx_interrupt
Mike McCormack [Mon, 30 May 2011 23:50:24 +0000]
rtlwifi: Fix logic in rx_interrupt

Should pass along packet if there's no CRC and no hardware error.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoRevert "mac80211: stop queues before rate control updation"
John W. Linville [Tue, 7 Jun 2011 18:03:08 +0000]
Revert "mac80211: stop queues before rate control updation"

This reverts commit 1d38c16ce4156f63b45abbd09dd28ca2ef5172b4.

The mac80211 maintainer raised complaints about abuse of the CSA stop
reason, and about whether this patch actually serves its intended
purpose at all.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agonet: cpu offline cause napi stall
Heiko Carstens [Mon, 6 Jun 2011 20:50:03 +0000]
net: cpu offline cause napi stall

Frank Blaschka reported :
<quote>
  During heavy network load we turn off/on cpus.
  Sometimes this causes a stall on the network device.
  Digging into the dump I found out following:

  napi is scheduled but does not run. From the I/O buffers
  and the napi state I see napi/rx_softirq processing has stopped
  because the budget was reached. napi stays in the
  softnet_data poll_list and the rx_softirq was raised again.

  I assume at this time the cpu offline comes in,
  the rx softirq is raised/moved to another cpu but napi stays in the
  poll_list of the softnet_data of the now offline cpu.

  Reviewing dev_cpu_callback (net/core/dev.c) I did not find the
  poll_list is transfered to the new cpu.
</quote>

This patch is a straightforward implementation of Frank suggestion :

Transfert poll_list and trigger NET_RX_SOFTIRQ on new cpu.

Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agobridge: provide a cow_metrics method for fake_ops
Alexander Holler [Tue, 7 Jun 2011 07:51:35 +0000]
bridge: provide a cow_metrics method for fake_ops

Like in commit 0972ddb237 (provide cow_metrics() methods to blackhole
dst_ops), we must provide a cow_metrics for bridges fake_dst_ops as
well.

This fixes a regression coming from commits 62fa8a846d7d (net: Implement
read-only protection and COW'ing of metrics.) and 33eb9873a28 (bridge:
initialize fake_rtable metrics)

ip link set mybridge mtu 1234
-->
[  136.546243] Pid: 8415, comm: ip Tainted: P
2.6.39.1-00006-g40545b7 #103 ASUSTeK Computer Inc.         V1Sn
        /V1Sn
[  136.546256] EIP: 0060:[<00000000>] EFLAGS: 00010202 CPU: 0
[  136.546268] EIP is at 0x0
[  136.546273] EAX: f14a389c EBX: 000005d4 ECX: f80d32c0 EDX: f80d1da1
[  136.546279] ESI: f14a3000 EDI: f255bf10 EBP: f15c3b54 ESP: f15c3b48
[  136.546285]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  136.546293] Process ip (pid: 8415, ti=f15c2000 task=f4741f80
task.ti=f15c2000)
[  136.546297] Stack:
[  136.546301]  f80c658f f14a3000 ffffffed f15c3b64 c12cb9c8 f80d1b80
ffffffa1 f15c3bbc
[  136.546315]  c12da347 c12d9c7d 00000000 f7670b00 00000000 f80d1b80
ffffffa6 f15c3be4
[  136.546329]  00000004 f14a3000 f255bf20 00000008 f15c3bbc c11d6cae
00000000 00000000
[  136.546343] Call Trace:
[  136.546359]  [<f80c658f>] ? br_change_mtu+0x5f/0x80 [bridge]
[  136.546372]  [<c12cb9c8>] dev_set_mtu+0x38/0x80
[  136.546381]  [<c12da347>] do_setlink+0x1a7/0x860
[  136.546390]  [<c12d9c7d>] ? rtnl_fill_ifinfo+0x9bd/0xc70
[  136.546400]  [<c11d6cae>] ? nla_parse+0x6e/0xb0
[  136.546409]  [<c12db931>] rtnl_newlink+0x361/0x510
[  136.546420]  [<c1023240>] ? vmalloc_sync_all+0x100/0x100
[  136.546429]  [<c1362762>] ? error_code+0x5a/0x60
[  136.546438]  [<c12db5d0>] ? rtnl_configure_link+0x80/0x80
[  136.546446]  [<c12db27a>] rtnetlink_rcv_msg+0xfa/0x210
[  136.546454]  [<c12db180>] ? __rtnl_unlock+0x20/0x20
[  136.546463]  [<c12ee0fe>] netlink_rcv_skb+0x8e/0xb0
[  136.546471]  [<c12daf1c>] rtnetlink_rcv+0x1c/0x30
[  136.546479]  [<c12edafa>] netlink_unicast+0x23a/0x280
[  136.546487]  [<c12ede6b>] netlink_sendmsg+0x26b/0x2f0
[  136.546497]  [<c12bb828>] sock_sendmsg+0xc8/0x100
[  136.546508]  [<c10adf61>] ? __alloc_pages_nodemask+0xe1/0x750
[  136.546517]  [<c11d0602>] ? _copy_from_user+0x42/0x60
[  136.546525]  [<c12c5e4c>] ? verify_iovec+0x4c/0xc0
[  136.546534]  [<c12bd805>] sys_sendmsg+0x1c5/0x200
[  136.546542]  [<c10c2150>] ? __do_fault+0x310/0x410
[  136.546549]  [<c10c2c46>] ? do_wp_page+0x1d6/0x6b0
[  136.546557]  [<c10c47d1>] ? handle_pte_fault+0xe1/0x720
[  136.546565]  [<c12bd1af>] ? sys_getsockname+0x7f/0x90
[  136.546574]  [<c10c4ec1>] ? handle_mm_fault+0xb1/0x180
[  136.546582]  [<c1023240>] ? vmalloc_sync_all+0x100/0x100
[  136.546589]  [<c10233b3>] ? do_page_fault+0x173/0x3d0
[  136.546596]  [<c12bd87b>] ? sys_recvmsg+0x3b/0x60
[  136.546605]  [<c12bdd83>] sys_socketcall+0x293/0x2d0
[  136.546614]  [<c13629d0>] sysenter_do_call+0x12/0x26
[  136.546619] Code:  Bad EIP value.
[  136.546627] EIP: [<00000000>] 0x0 SS:ESP 0068:f15c3b48
[  136.546645] CR2: 0000000000000000
[  136.546652] ---[ end trace 6909b560e78934fa ]---

Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoaf_packet: prevent information leak
Eric Dumazet [Tue, 7 Jun 2011 05:42:06 +0000]
af_packet: prevent information leak

In 2.6.27, commit 393e52e33c6c2 (packet: deliver VLAN TCI to userspace)
added a small information leak.

Add padding field and make sure its zeroed before copy to user.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoirda: iriap: Use seperate lockdep class for irias_objects->hb_spinlock
David S. Miller [Tue, 7 Jun 2011 00:00:35 +0000]
irda: iriap: Use seperate lockdep class for irias_objects->hb_spinlock

The SEQ output functions grab the obj->attrib->hb_spinlock lock of
sub-objects found in the hash traversal.  These locks are in a different
realm than the one used for the irias_objects hash table itself.

So put the latter into it's own lockdep class.

Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet: Rework netdev_drivername() to avoid warning.
David S. Miller [Mon, 6 Jun 2011 23:41:33 +0000]
net: Rework netdev_drivername() to avoid warning.

This interface uses a temporary buffer, but for no real reason.
And now can generate warnings like:

net/sched/sch_generic.c: In function dev_watchdog
net/sched/sch_generic.c:254:10: warning: unused variable drivername

Just return driver->name directly or "".

Reported-by: Connor Hansen <cmdkhh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet/ipv6: check for mistakenly passed in non-AF_INET6 sockaddrs
Marcus Meissner [Mon, 6 Jun 2011 06:00:07 +0000]
net/ipv6: check for mistakenly passed in non-AF_INET6 sockaddrs

Same check as for IPv4, also do for IPv6.

(If you passed in a IPv4 sockaddr_in here, the sizeof check
 in the line before would have triggered already though.)

Signed-off-by: Marcus Meissner <meissner@suse.de>
Cc: Reinhard Max <max@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoMerge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville...
David S. Miller [Mon, 6 Jun 2011 20:25:36 +0000]
Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless-2.6

8 years agoiwl4965: set tx power after rxon_assoc
Stanislaw Gruszka [Mon, 6 Jun 2011 13:11:30 +0000]
iwl4965: set tx power after rxon_assoc

Setting tx power can be deferred during scan or changing channel.
If after that correct tx power settings will not be sent to device,
we can observe transmission problems and timeouts. Force to send
tx power settings also after partial rxon change, to assure device
always be configured with up-to-date settings.

Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=36492

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agort2x00: fix rmmod crash
Stanislaw Gruszka [Sat, 4 Jun 2011 14:48:54 +0000]
rt2x00: fix rmmod crash

Avoid queue and run autowakeup_work when device is not present anymore.
That prevent rmmod and device remove crash introduced by:

commit 1c0bcf89d85cc97a0d9ce4cd909351a81fa4fdde
Author: Ivo van Doorn <ivdoorn@gmail.com>
Date:   Sat Apr 30 17:18:18 2011 +0200

    rt2x00: Add autowake support for USB hardware

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoiwlagn: use cts-to-self protection on 5000 adapters series
Stanislaw Gruszka [Thu, 26 May 2011 15:14:22 +0000]
iwlagn: use cts-to-self protection on 5000 adapters series

This patch fixes 802.11n stability and performance regression we have
since 2.6.35. It boost performance on my 5GHz N-only network from about
5MB/s to 8MB/s. Similar percentage boost can be observed on 2.4 GHz.

These are test results of 5x downloading of approximately 700MB iso
image:

vanilla: 5.27 5.22 4.94 4.47 5.31 ; avr 5.0420 std 0.35110
patched: 8.07 7.95 8.06 7.99 7.96 ; avr 8.0060 std 0.055946

This was achieved with NetworkManager configured to do not perform
periodical scans, by configuring constant BSSID. With periodical scans,
after some time, performance downgrade to unpatched driver level, like
in example below:

patched: 7.40 7.61 4.28 4.37 4.80 avr 5.6920 std 1.6683

However patch still make better here, since similar test on unpatched
driver make link disconnects with below messages after some time:

wlan1: authenticate with 00:23:69:35:d1:3f (try 1)
wlan1: authenticate with 00:23:69:35:d1:3f (try 2)
wlan1: authenticate with 00:23:69:35:d1:3f (try 3)
wlan1: authentication with 00:23:69:35:d1:3f timed out

On 2.6.35 kernel patch helps against connection hangs with messages:

iwlagn 0000:20:00.0: queue 10 stuck 3 time. Fw reload.
iwlagn 0000:20:00.0: On demand firmware reload
iwlagn 0000:20:00.0: Stopping AGG while state not ON or starting

Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoRevert "mac80211: Skip tailroom reservation for full HW-crypto devices"
John W. Linville [Mon, 6 Jun 2011 18:35:27 +0000]
Revert "mac80211: Skip tailroom reservation for full HW-crypto devices"

This reverts commit aac6af5534fade2b18682a0b9efad1a6c04c34c6.

Conflicts:

net/mac80211/key.c

That commit has a race that causes a warning, as documented in the thread
here:

http://marc.info/?l=linux-wireless&m=130717684914101&w=2

Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
John W. Linville [Mon, 6 Jun 2011 17:58:21 +0000]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6 into for-davem

8 years agoMerge branch 'pablo/nf-2.6-updates' of git://1984.lsi.us.es/net-2.6
David S. Miller [Mon, 6 Jun 2011 00:14:04 +0000]
Merge branch 'pablo/nf-2.6-updates' of git://1984.lsi.us.es/net-2.6

8 years agonet: fix smc91x.c device tree support
Grant Likely [Fri, 3 Jun 2011 21:31:27 +0000]
net: fix smc91x.c device tree support

Fix missing semicolon at end of smc91x.c match tabledevice driver.
Also remove unnecessary #ifdef around of_match_table pointer.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonetfilter: use unsigned variables for packet lengths in ip[6]_queue.
Dave Jones [Sat, 28 May 2011 00:36:51 +0000]
netfilter: use unsigned variables for packet lengths in ip[6]_queue.

Netlink message lengths can't be negative, so use unsigned variables.

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

8 years agonetfilter: nf_conntrack: fix ct refcount leak in l4proto->error()
Pablo Neira Ayuso [Thu, 2 Jun 2011 13:08:45 +0000]
netfilter: nf_conntrack: fix ct refcount leak in l4proto->error()

This patch fixes a refcount leak of ct objects that may occur if
l4proto->error() assigns one conntrack object to one skbuff. In
that case, we have to skip further processing in nf_conntrack_in().

With this patch, we can also fix wrong return values (-NF_ACCEPT)
for special cases in ICMP[v6] that should not bump the invalid/error
statistic counters.

Reported-by: Zoltan Menyhart <Zoltan.Menyhart@bull.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

8 years agonetfilter: nf_nat: fix crash in nf_nat_csum
Julian Anastasov [Sun, 29 May 2011 20:42:29 +0000]
netfilter: nf_nat: fix crash in nf_nat_csum

Fix crash in nf_nat_csum when mangling packets
in OUTPUT hook where skb->dev is not defined, it is set
later before POSTROUTING. Problem happens for CHECKSUM_NONE.
We can check device from rt but using CHECKSUM_PARTIAL
should be safe (skb_checksum_help).

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

8 years agonetfilter: ipset: Use the stored first cidr value instead of '1'
Jozsef Kadlecsik [Wed, 1 Jun 2011 21:35:49 +0000]
netfilter: ipset: Use the stored first cidr value instead of '1'

The stored cidr values are tried one after anoter. The boolean
condition evaluated to '1' instead of the first stored cidr or
the default host cidr.

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

8 years agonetfilter: ipset: Fix return code for destroy when sets are in use
Jozsef Kadlecsik [Wed, 1 Jun 2011 21:35:48 +0000]
netfilter: ipset: Fix return code for destroy when sets are in use

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

8 years agoipvs: restore support for iptables SNAT
Julian Anastasov [Thu, 2 Jun 2011 00:09:54 +0000]
ipvs: restore support for iptables SNAT

Fix the IPVS priority in LOCAL_IN hook,
so that SNAT target in POSTROUTING is supported for IPVS
traffic as in 2.6.36 where it worked depending on
module load order.

Before 2.6.37 we used priority 100 in LOCAL_IN to
process remote requests. We used the same priority as
iptables SNAT and if IPVS handlers are installed before
SNAT handlers we supported SNAT in POSTROUTING for the IPVS
traffic. If SNAT is installed before IPVS, the netfilter
handlers are before IPVS and netfilter checks the NAT
table twice for the IPVS requests: once in LOCAL_IN where
IPS_SRC_NAT_DONE is set and second time in POSTROUTING
where the SNAT rules are ignored because IPS_SRC_NAT_DONE
was already set in LOCAL_IN.

But in 2.6.37 we changed the IPVS priority for
LOCAL_IN with the goal to be unique (101) forgetting the
fact that for IPVS traffic we should not walk both
LOCAL_IN and POSTROUTING nat tables.

So, change the priority for processing remote
IPVS requests from 101 to 99, i.e. before NAT_SRC (100)
because we prefer to support SNAT in POSTROUTING
instead of LOCAL_IN. It also moves the priority for
IPVS replies from 99 to 98. Use constants instead of
magic numbers at these places.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

8 years agonetfilter: add more values to enum ip_conntrack_info
Eric Dumazet [Thu, 19 May 2011 13:44:27 +0000]
netfilter: add more values to enum ip_conntrack_info

Following error is raised (and other similar ones) :

net/ipv4/netfilter/nf_nat_standalone.c: In function ‘nf_nat_fn’:
net/ipv4/netfilter/nf_nat_standalone.c:119:2: warning: case value ‘4’
not in enumerated type ‘enum ip_conntrack_info’

gcc barfs on adding two enum values and getting a not enumerated
result :

case IP_CT_RELATED+IP_CT_IS_REPLY:

Add missing enum values

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

8 years agobonding: reset queue mapping prior to transmission to physical device (v5)
Neil Horman [Fri, 3 Jun 2011 10:35:52 +0000]
bonding: reset queue mapping prior to transmission to physical device (v5)

The bonding driver is multiqueue enabled, in which each queue represents a slave
to enable optional steering of output frames to given slaves against the default
output policy.  However, it needs to reset the skb->queue_mapping prior to
queuing to the physical device or the physical slave (if it is multiqueue) could
wind up transmitting on an unintended tx queue

Change Notes:
v2) Based on first pass review, updated the patch to restore the origional queue
mapping that was found in bond_select_queue, rather than simply resetting to
zero.  This preserves the value of queue_mapping when it was set on receive in
the forwarding case which is desireable.

v3) Fixed spelling an casting error in skb->cb

v4) fixed to store raw queue_mapping to avoid double decrement

v5) Eric D requested that ->cb access be wrapped in a macro.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoqlcnic: Avoid double free of skb in tx path
Sucheta Chakraborty [Fri, 3 Jun 2011 05:52:18 +0000]
qlcnic: Avoid double free of skb in tx path

buffer->skb should be marked NULL to avoid double free of the skb.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoqlcnic: Fix bug in FW queue dump
Anirban Chakraborty [Thu, 2 Jun 2011 12:42:21 +0000]
qlcnic: Fix bug in FW queue dump

Due to a change in FW template, a bug was introduced in dump queue entries. This is
fixed by reinitializing queue address before looping for each que dump operation.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agofix return values of l2tp_dfs_seq_open()
Al Viro [Sun, 5 Jun 2011 00:54:03 +0000]
fix return values of l2tp_dfs_seq_open()

More fallout from struct net lifetime rules review: PTR_ERR() is *already*
negative and failing ->open() should return negatives on failure.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoget_net_ns_by_fd() oopses if proc_ns_fget() returns an error
Al Viro [Sun, 5 Jun 2011 00:37:35 +0000]
get_net_ns_by_fd() oopses if proc_ns_fget() returns an error

BTW, looking through the code related to struct net lifetime rules has
caught something else:

struct net *get_net_ns_by_fd(int fd)
{
        ...
        file = proc_ns_fget(fd);
        if (!file)
                goto out;

        ei = PROC_I(file->f_dentry->d_inode);

while in proc_ns_fget() we have two return ERR_PTR(...) and not a single
path that would return NULL.  The other caller of proc_ns_fget() treats
ERR_PTR() correctly...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
Linus Torvalds [Sat, 4 Jun 2011 14:19:51 +0000]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] Fix oops caused by queue refcounting failure

8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Sat, 4 Jun 2011 14:16:00 +0000]
Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
  tg3: Fix tg3_skb_error_unmap()
  net: tracepoint of net_dev_xmit sees freed skb and causes panic
  drivers/net/can/flexcan.c: add missing clk_put
  net: dm9000: Get the chip in a known good state before enabling interrupts
  drivers/net/davinci_emac.c: add missing clk_put
  af-packet: Add flag to distinguish VID 0 from no-vlan.
  caif: Fix race when conditionally taking rtnl lock
  usbnet/cdc_ncm: add missing .reset_resume hook
  vlan: fix typo in vlan_dev_hard_start_xmit()
  net/ipv4: Check for mistakenly passed in non-IPv4 address
  iwl4965: correctly validate temperature value
  bluetooth l2cap: fix locking in l2cap_global_chan_by_psm
  ath9k: fix two more bugs in tx power
  cfg80211: don't drop p2p probe responses
  Revert "net: fix section mismatches"
  drivers/net/usb/catc.c: Fix potential deadlock in catc_ctrl_run()
  sctp: stop pending timers and purge queues when peer restart asoc
  drivers/net: ks8842 Fix crash on received packet when in PIO mode.
  ip_options_compile: properly handle unaligned pointer
  iwlagn: fix incorrect PCI subsystem id for 6150 devices
  ...

8 years agoMerge branch 'for-linus' of git://git.kernel.dk/linux-block
Linus Torvalds [Fri, 3 Jun 2011 23:11:26 +0000]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: Use hlist_entry() for io_context.cic_list.first
  cfq-iosched: Remove bogus check in queue_fail path
  xen/blkback: potential null dereference in error handling
  xen/blkback: don't call vbd_size() if bd_disk is NULL
  block: blkdev_get() should access ->bd_disk only after success
  CFQ: Fix typo and remove unnecessary semicolon
  block: remove unwanted semicolons
  Revert "block: Remove extra discard_alignment from hd_struct."
  nbd: adjust 'max_part' according to part_shift
  nbd: limit module parameters to a sane value
  nbd: pass MSG_* flags to kernel_recvmsg()
  block: improve the bio_add_page() and bio_add_pc_page() descriptions

8 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier...
Linus Torvalds [Fri, 3 Jun 2011 23:04:10 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/vapier/blackfin

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
  Blackfin: strncpy: fix handling of zero lengths

8 years agoMerge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux...
Linus Torvalds [Fri, 3 Jun 2011 23:03:16 +0000]
Merge branch 'stable' of git://git./linux/kernel/git/cmetcalf/linux-tile

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  asm-generic/unistd.h: support sendmmsg syscall
  tile: enable CONFIG_BUGVERBOSE

8 years agoMerge branch 'linux-next' of git://git.infradead.org/ubifs-2.6
Linus Torvalds [Fri, 3 Jun 2011 22:59:32 +0000]
Merge branch 'linux-next' of git://git.infradead.org/ubifs-2.6

* 'linux-next' of git://git.infradead.org/ubifs-2.6:
  UBIFS: fix-up free space earlier
  UBIFS: intialize LPT earlier
  UBIFS: assert no fixup when writing a node
  UBIFS: fix clean znode counter corruption in error cases
  UBIFS: fix memory leak on error path
  UBIFS: fix shrinker object count reports
  UBIFS: fix recovery broken by the previous recovery fix
  UBIFS: amend ubifs_recover_leb interface
  UBIFS: introduce a "grouped" journal head flag
  UBIFS: supress false error messages

8 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt...
Linus Torvalds [Fri, 3 Jun 2011 22:58:48 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/rostedt/linux-2.6-ktest

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-ktest:
  ktest: Ignore unset values of the minconfig in config_bisect
  ktest: Fix result of rebooting the kernel
  ktest: Fix off-by-one in config bisect result

8 years agoMerge branch 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Fri, 3 Jun 2011 22:53:23 +0000]
Merge branch 'rmobile-fixes-for-linus' of git://git./linux/kernel/git/lethal/sh-2.6

* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  ARM: mach-shmobile: add DMAC clock definitions on SH7372
  ARM: arch-shmobile: support SDHI card detection on mackerel, using a GPIO
  sh_mobile_meram: MERAM platform data for LCDC

8 years agoMerge branch 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Fri, 3 Jun 2011 22:04:25 +0000]
Merge branch 'sh-fixes-for-linus' of git://git./linux/kernel/git/lethal/sh-2.6

* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  dmaengine: shdma: fix a regression: initialise DMA channels for memcpy
  dmaengine: shdma: Fix up fallout from runtime PM changes.
  Revert "clocksource: sh_cmt: Runtime PM support"
  Revert "clocksource: sh_tmu: Runtime PM support"
  sh: Fix up asm-generic/ptrace.h fallout.
  sh64: Move from P1SEG to CAC_ADDR for consistent sync.
  sh64: asm/pgtable.h needs asm/mmu.h
  sh: asm/tlb.h needs linux/swap.h
  sh: mark DMA slave ID 0 as invalid
  sh: Update shmin to reflect PIO dependency.
  sh: arch/sh/kernel/process_32.c needs linux/prefetch.h.
  sh: add MMCIF runtime PM support on ecovec
  sh: switch ap325rxa to dynamically manage the platform camera

8 years agoRevert "ASoC: Update cx20442 for TTY API change"
Linus Torvalds [Fri, 3 Jun 2011 22:00:50 +0000]
Revert "ASoC: Update cx20442 for TTY API change"

This reverts commit ed0bd2333cffc3d856db9beb829543c1dfc00982.

Since we reverted the TTY API change, we should revert the ASoC update
to it too.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoRevert "tty: make receive_buf() return the amout of bytes received"
Linus Torvalds [Fri, 3 Jun 2011 21:33:24 +0000]
Revert "tty: make receive_buf() return the amout of bytes received"

This reverts commit b1c43f82c5aa265442f82dba31ce985ebb7aa71c.

It was broken in so many ways, and results in random odd pty issues.

It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit a5660b41af6a: "tty: fix endless
work loop when the buffer fills up").

It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.

And it didn't actually work at all.  BenH bisected down odd tty behavior
to it:
  "It looks like the patch is causing some major malfunctions of the X
   server for me, possibly related to PTYs.  For example, cat'ing a
   large file in a gnome terminal hangs the kernel for -minutes- in a
   loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
   data in the quoted bits further down).

   ...

   Some more data: It -looks- like what happens is that the
   flush_to_ldisc work queue entry constantly re-queues itself (because
   the PTY is full ?) and the workqueue thread will basically loop
   forver calling it without ever scheduling, thus starving the consumer
   process that could have emptied the PTY."

which is pretty much exactly the problem we fixed in a5660b41af6a.

Milton Miller pointed out the 'unsigned int' issue.

Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Milton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
John W. Linville [Fri, 3 Jun 2011 18:31:50 +0000]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6 into for-davem

8 years agolibertas_sdio: handle spurious interrupts
Daniel Drake [Thu, 2 Jun 2011 23:13:26 +0000]
libertas_sdio: handle spurious interrupts

Commit 06e8935febe687e2a561707d4c7ca4245d261dbe adds an IRQ handling
optimization for single-function SDIO cards like this one, but at the
same time exposes a small hardware bug.

During hardware init, an interrupt is generated with (apparently) no
source. Previously, mmc threw this interrupt away, but now (due to the
optimization), the mmc layer passes this onto libertas, before it is ready
(and before it has enabled interrupts), causing a crash.

Work around this hardware bug by registering the IRQ handler later and
making it capable of handling interrupts with no cause. The change that
makes the IRQ handler registration happen later actually eliminates
the spurious interrupt as well.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agomac80211: call dev_alloc_name before copying name to sdata
Thadeu Lima de Souza Cascardo [Thu, 2 Jun 2011 20:28:37 +0000]
mac80211: call dev_alloc_name before copying name to sdata

This partially reverts 1c5cae815d19ffe02bdfda1260949ef2b1806171, because
the netdev name is copied into sdata->name, which is used for debugging
messages, for example. Otherwise, we get messages like this:

wlan%d: authenticated

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoiwlagn: fix channel switch locking
Stanislaw Gruszka [Thu, 2 Jun 2011 16:17:15 +0000]
iwlagn: fix channel switch locking

We use priv->mutex to avoid race conditions between iwl_chswitch_done()
and iwlagn_mac_channel_switch(), when marking channel switch in
progress. But iwl_chswitch_done() can be called in atomic context
from iwl_rx_csa() or with mutex already taken from iwlagn_commit_rxon().

These bugs were introduced by:

commit 79d07325502e73508f917475bc1617b60979dd94
Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Date:   Thu May 6 08:54:11 2010 -0700

    iwlwifi: support channel switch offload in driver

To fix remove mutex from iwl_chswitch_done() and use atomic bitops for
marking channel switch pending.

Also remove iwl2030_hw_channel_switch() since 2000 series adapters are
2.4GHz only devices.

Cc: stable@kernel.org # 2.6.36+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoath5k: Disable fast channel switching by default
Nick Kossifidis [Thu, 2 Jun 2011 00:09:48 +0000]
ath5k: Disable fast channel switching by default

Disable fast channel change by default on AR2413/AR5413 due to
some bug reports (it still works for me but it's better to be safe).
Add a module parameter "fastchanswitch" in case anyone wants to enable
it and play with it.

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agossb: fix PCI(e) driver regression causing oops on PCI cards
Rafał Miłecki [Wed, 1 Jun 2011 09:01:11 +0000]
ssb: fix PCI(e) driver regression causing oops on PCI cards

We were incorrectly executing PCIe specific workarounds on PCI cards.
This resulted in:
Machine check in kernel mode.
Caused by (from SRR1=149030): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]

Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoUBIFS: fix-up free space earlier
Ben Gardiner [Mon, 30 May 2011 18:56:16 +0000]
UBIFS: fix-up free space earlier

The free space fixup is currently initiated during mount after the call to
ubifs_write_master() which results in a write to PEBs; this has been observed
with the patch 'assert no fixup when writing a node' applied:

Move the free space fixup on mount to before the calls to
ubifs_recover_inl_heads() and ubifs_write_master(). This results in no
assertions with the previously mentioned patch applied.

Artem: tweaked the patch a bit

Signed-off-by: Ben Gardiner <bengardiner@nanometrics>
Reviewed-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

8 years agoUBIFS: intialize LPT earlier
Ben Gardiner [Mon, 30 May 2011 18:56:15 +0000]
UBIFS: intialize LPT earlier

The current 'mount_ubifs()' implementation does not initialize the LPT until the
the master node is marked dirty. Move the LPT initialization to before marking
the master node dirty. This is a preparation for the next patch which will move
the free-space-fixup check to before marking the master node dirty, because we
have to fix-up the free space before doing any writes.

Artem: massaged the patch and commit message.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

8 years agoUBIFS: assert no fixup when writing a node
Ben Gardiner [Mon, 30 May 2011 18:56:14 +0000]
UBIFS: assert no fixup when writing a node

The current free space fixup can result in some writing to the UBI volume
when the space_fixup flag is set.

To catch instances where UBIFS is writing to the NAND while the space_fixup
flag is set, add an assert to ubifs_write_node().

Artem: tweaked the patch, added similar assertion to the write buffer
       write path.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

8 years agoUBIFS: fix clean znode counter corruption in error cases
Artem Bityutskiy [Tue, 31 May 2011 11:26:07 +0000]
UBIFS: fix clean znode counter corruption in error cases

UBIFS maintains per-filesystem and global clean znode counters
('c->clean_zn_cnt' and 'ubifs_clean_zn_cnt'). It is important to maintain
correct values there since the shrinker relies on 'ubifs_clean_zn_cnt'.

However, in case of failures during commit the counters were corrupted. E.g.,
if a failure happens in the middle of 'write_index()', then some nodes in the
commit list ('c->cnext') are marked as clean, and some are marked as dirty. And
the 'ubifs_destroy_tnc_subtree()' frees does not retrun correct count, and we
end up with non-zero 'c->clean_zn_cnt' when unmounting. This means that if we
have 2 file-sytem and one of them fails, and we unmount it,
'ubifs_clean_zn_cnt' stays incorrect and confuses the shrinker.

Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

8 years agoUBIFS: fix memory leak on error path
Artem Bityutskiy [Tue, 31 May 2011 05:40:40 +0000]
UBIFS: fix memory leak on error path

UBIFS leaks memory on error path in 'ubifs_jnl_update()' in case of write
failure because it forgets to free the 'struct ubifs_dent_node *dent' object.
Although the object is small, the alignment can make it large - e.g., 2KiB
if the min. I/O unit is 2KiB.

Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org

8 years agoUBIFS: fix shrinker object count reports
Artem Bityutskiy [Tue, 31 May 2011 04:03:21 +0000]
UBIFS: fix shrinker object count reports

Sometimes VM asks the shrinker to return amount of objects it can shrink,
and we return the ubifs_clean_zn_cnt in that case. However, it is possible
that this counter is negative for a short period of time, due to the way
UBIFS TNC code updates it. And I can observe the following warnings sometimes:

shrink_slab: ubifs_shrinker+0x0/0x2b7 [ubifs] negative objects to delete nr=-8541616642706119788

This patch makes sure UBIFS never returns negative count of objects.

Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org

8 years agoBlackfin: strncpy: fix handling of zero lengths
Steven Miao [Wed, 1 Jun 2011 07:52:41 +0000]
Blackfin: strncpy: fix handling of zero lengths

The jump to 4f will cause the NUL padding loop to run at least one time,
so if string length is zero just jump to the end.  Otherwise we wrongly
write one NUL byte when size==0.

Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

8 years agotg3: Fix tg3_skb_error_unmap()
Matt Carlson [Thu, 2 Jun 2011 13:01:39 +0000]
tg3: Fix tg3_skb_error_unmap()

This function attempts to free one fragment beyond the number of
fragments that were actually mapped.  This patch brings back the limit
to the correct spot.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet: tracepoint of net_dev_xmit sees freed skb and causes panic
Koki Sanagi [Mon, 30 May 2011 21:48:34 +0000]
net: tracepoint of net_dev_xmit sees freed skb and causes panic

Because there is a possibility that skb is kfree_skb()ed and zero cleared
after ndo_start_xmit, we should not see the contents of skb like skb->len and
skb->dev->name after ndo_start_xmit. But trace_net_dev_xmit does that
and causes panic by NULL pointer dereference.
This patch fixes trace_net_dev_xmit not to see the contents of skb directly.

If you want to reproduce this panic,

1. Get tracepoint of net_dev_xmit on
2. Create 2 guests on KVM
2. Make 2 guests use virtio_net
4. Execute netperf from one to another for a long time as a network burden
5. host will panic(It takes about 30 minutes)

Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoasm-generic/unistd.h: support sendmmsg syscall
Chris Metcalf [Thu, 2 Jun 2011 18:21:45 +0000]
asm-generic/unistd.h: support sendmmsg syscall

Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>

8 years agoktest: Ignore unset values of the minconfig in config_bisect
Steven Rostedt [Thu, 2 Jun 2011 03:27:19 +0000]
ktest: Ignore unset values of the minconfig in config_bisect

By ignoring the unset values of the minconfig in deciding
what to test in the config_bisect can cause the problem
config from being tested too.

Just do not test the configs that are set in the minconfig.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

8 years agoktest: Fix result of rebooting the kernel
Steven Rostedt [Thu, 2 Jun 2011 03:25:13 +0000]
ktest: Fix result of rebooting the kernel

The command that is called that reboots the kernel may fail
but the return code is not passed back to the ktest.pl script.
This is because a ';' is used between the two commands and
if the second command fails, only the first command's return
code is returned. Using a '&&' between the two commands fixes
this.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

8 years agoktest: Fix off-by-one in config bisect result
Steven Rostedt [Thu, 2 Jun 2011 03:22:30 +0000]
ktest: Fix off-by-one in config bisect result

Because in perl the array size returned by $#arr, is the last
index and not the actually size of the array, we end the config
bisect early, thinking there is only one config left when there
are in fact two. Thus the result has a 50% chance of picking
the correct config that caused the problem.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

8 years agoMerge branch 'for-jens/xen-blkback.fixes' of git://git.kernel.org/pub/scm/linux/kerne...
Jens Axboe [Thu, 2 Jun 2011 11:14:15 +0000]
Merge branch 'for-jens/xen-blkback.fixes' of git://git./linux/kernel/git/konrad/xen into for-linus

8 years agoblock: Use hlist_entry() for io_context.cic_list.first
Paul Bolle [Thu, 2 Jun 2011 11:05:02 +0000]
block: Use hlist_entry() for io_context.cic_list.first

list_entry() and hlist_entry() are both simply aliases for
container_of(), but since io_context.cic_list.first is an hlist_node one
should at least use the correct alias.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

8 years agocfq-iosched: Remove bogus check in queue_fail path
Paul Bolle [Thu, 2 Jun 2011 11:05:02 +0000]
cfq-iosched: Remove bogus check in queue_fail path

queue_fail can only be reached if cic is NULL, so its check for cic must
be bogus.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

8 years ago[SCSI] Fix oops caused by queue refcounting failure
James Bottomley [Wed, 25 May 2011 20:52:14 +0000]
[SCSI] Fix oops caused by queue refcounting failure

In certain circumstances, we can get an oops from a torn down device.
Most notably this is from CD roms trying to call scsi_ioctl.  The root
cause of the problem is the fact that after scsi_remove_device() has
been called, the queue is fully torn down.  This is actually wrong
since the queue can be used until the sdev release function is called.
Therefore, we add an extra reference to the queue which is released in
sdev->release, so the queue always exists.

Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>

8 years agodrivers/net/can/flexcan.c: add missing clk_put
Julia Lawall [Wed, 1 Jun 2011 19:48:50 +0000]
drivers/net/can/flexcan.c: add missing clk_put

The failed_get label is used after the call to clk_get has succeeded, so it
should be moved up above the call to clk_put.

The failed_req labels doesn't do anything different than failed_get, so
delete it.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression e1,e2;
statement S;
@@

e1 = clk_get@p1(...);
... when != e1 = e2
    when != clk_put(e1)
    when any
if (...) { ... when != clk_put(e1)
               when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
 } else S
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoARM: mach-shmobile: add DMAC clock definitions on SH7372
Guennadi Liakhovetski [Wed, 1 Jun 2011 07:32:07 +0000]
ARM: mach-shmobile: add DMAC clock definitions on SH7372

These definitions are needed to let the runtime PM subsystem turn off
DMAC clocks, when it is suspended by the driver.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

8 years agodmaengine: shdma: fix a regression: initialise DMA channels for memcpy
Guennadi Liakhovetski [Tue, 31 May 2011 09:25:16 +0000]
dmaengine: shdma: fix a regression: initialise DMA channels for memcpy

A recent patch has introduced a regression, where repeating a memcpy
DMA test with shdma module unloading between them skips the DMA channel
configuration. Fix this regression by always configuring the channel
during its allocation.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

8 years agonet: dm9000: Get the chip in a known good state before enabling interrupts
Mark Brown [Wed, 1 Jun 2011 10:18:09 +0000]
net: dm9000: Get the chip in a known good state before enabling interrupts

Currently the DM9000 driver requests the primary interrupt before it
resets the chip and puts it into a known good state. This means that if
the chip is asserting interrupt for some reason we can end up with a
screaming IRQ that the interrupt handler is unable to deal with. Avoid
this by only requesting the interrupt after we've reset the chip so we
know what state it's in.

This started manifesting itself on one of my boards in the past month or
so, I suspect as a result of some core infrastructure changes removing
some form of mitigation against bad behaviour here, even when things boot
it seems that the new code brings the interface up more quickly.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agodrivers/net/davinci_emac.c: add missing clk_put
Julia Lawall [Wed, 1 Jun 2011 07:10:10 +0000]
drivers/net/davinci_emac.c: add missing clk_put

Go to existing error handling code at the end of the function that calls
clk_put.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression e1,e2;
statement S;
@@

e1 = clk_get@p1(...);
... when != e1 = e2
    when != clk_put(e1)
    when any
if (...) { ... when != clk_put(e1)
               when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
 } else S
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoaf-packet: Add flag to distinguish VID 0 from no-vlan.
Ben Greear [Wed, 1 Jun 2011 06:49:10 +0000]
af-packet: Add flag to distinguish VID 0 from no-vlan.

Currently, user-space cannot determine if a 0 tcp_vlan_tci
means there is no VLAN tag or the VLAN ID was zero.

Add flag to make this explicit.  User-space can check for
TP_STATUS_VLAN_VALID || tp_vlan_tci > 0, which will be backwards
compatible. Older could would have just checked for tp_vlan_tci,
so it will work no worse than before.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agocaif: Fix race when conditionally taking rtnl lock
sjur.brandeland@stericsson.com [Wed, 1 Jun 2011 00:55:37 +0000]
caif: Fix race when conditionally taking rtnl lock

Take the RTNL lock unconditionally when calling dev_close.
Taking the lock conditionally may cause race conditions.

Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agousbnet/cdc_ncm: add missing .reset_resume hook
Stefan Metzmacher [Wed, 1 Jun 2011 02:01:41 +0000]
usbnet/cdc_ncm: add missing .reset_resume hook

This avoids messages like this after suspend:

   cdc_ncm 2-1.4:1.6: no reset_resume for driver cdc_ncm?
   cdc_ncm 2-1.4:1.7: no reset_resume for driver cdc_ncm?
   cdc_ncm 2-1.4:1.6: usb0: unregister 'cdc_ncm' usb-0000:00:1d.0-1.4, CDC NCM

This is important for the Ericsson F5521gw GSM/UMTS modem.
Otherwise modemmanager looses the fact that the cdc_ncm and cdc_acm devices
belong together.

The cdc_ether module does the same.

Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agovlan: fix typo in vlan_dev_hard_start_xmit()
Wei Yongjun [Tue, 31 May 2011 22:53:19 +0000]
vlan: fix typo in vlan_dev_hard_start_xmit()

commit 4af429d29b341bb1735f04c2fb960178ed5d52e7 (vlan: lockless
transmit path) have a typo in vlan_dev_hard_start_xmit(), using
u64_stats_update_begin() to end the stat update, it should be
u64_stats_update_end().

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet/ipv4: Check for mistakenly passed in non-IPv4 address
Marcus Meissner [Thu, 2 Jun 2011 04:05:22 +0000]
net/ipv4: Check for mistakenly passed in non-IPv4 address

Check against mistakenly passing in IPv6 addresses (which would result
in an INADDR_ANY bind) or similar incompatible sockaddrs.

Signed-off-by: Marcus Meissner <meissner@suse.de>
Cc: Reinhard Max <max@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoRevert "mm: fail GFP_DMA allocations when ZONE_DMA is not configured"
Linus Torvalds [Wed, 1 Jun 2011 21:11:24 +0000]
Revert "mm: fail GFP_DMA allocations when ZONE_DMA is not configured"

This reverts commit a197b59ae6e8bee56fcef37ea2482dc08414e2ac.

As rmk says:
 "Commit a197b59ae6e8 (mm: fail GFP_DMA allocations when ZONE_DMA is not
  configured) is causing regressions on ARM with various drivers which
  use GFP_DMA.

  The behaviour up until now has been to silently ignore that flag when
  CONFIG_ZONE_DMA is not enabled, and to allocate from the normal zone.
  However, as a result of the above commit, such allocations now fail
  which causes drivers to fail.  These are regressions compared to the
  previous kernel version."

so just revert it.

Requested-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoMerge git://git.infradead.org/iommu-2.6
Linus Torvalds [Wed, 1 Jun 2011 20:48:50 +0000]
Merge git://git.infradead.org/iommu-2.6

* git://git.infradead.org/iommu-2.6:
  intel-iommu: Fix off-by-one in RMRR setup
  intel-iommu: Add domain check in domain_remove_one_dev_info
  intel-iommu: Remove Host Bridge devices from identity mapping
  intel-iommu: Use coherent DMA mask when requested
  intel-iommu: Dont cache iova above 32bit
  intel-iommu: Speed up processing of the identity_mapping function
  intel-iommu: Check for identity mapping candidate using system dma mask
  intel-iommu: Only unlink device domains from iommu
  intel-iommu: Enable super page (2MiB, 1GiB, etc.) support
  intel-iommu: Flush unmaps at domain_exit
  intel-iommu: Remove obsolete comment from detect_intel_iommu
  intel-iommu: fix VT-d PMR disable for TXT on S3 resume

8 years agoblock: fix mismerge of the DISK_EVENT_MEDIA_CHANGE removal
Linus Torvalds [Wed, 1 Jun 2011 20:29:19 +0000]
block: fix mismerge of the DISK_EVENT_MEDIA_CHANGE removal

Jens' back-merge commit 698567f3fa79 ("Merge commit 'v2.6.39' into
for-2.6.40/core") was incorrectly done, and re-introduced the
DISK_EVENT_MEDIA_CHANGE lines that had been removed earlier in commits

 - 9fd097b14918 ("block: unexport DISK_EVENT_MEDIA_CHANGE for
   legacy/fringe drivers")

 - 7eec77a1816a ("ide: unexport DISK_EVENT_MEDIA_CHANGE for ide-gd
   and ide-cd")

because of conflicts with the "g->flags" updates near-by by commit
d4dc210f69bc ("block: don't block events on excl write for non-optical
devices")

As a result, we re-introduced the hanging behavior due to infinite disk
media change reports.

Tssk, tssk, people! Don't do back-merges at all, and *definitely* don't
do them to hide merge conflicts from me - especially as I'm likely
better at merging them than you are, since I do so many merges.

Reported-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agotile: enable CONFIG_BUGVERBOSE
Chris Metcalf [Wed, 1 Jun 2011 20:06:04 +0000]
tile: enable CONFIG_BUGVERBOSE

Trivial config change to enable backtraces on panic.

Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>

8 years agoiwl4965: correctly validate temperature value
Stanislaw Gruszka [Wed, 1 Jun 2011 15:17:57 +0000]
iwl4965: correctly validate temperature value

In some cases we can read wrong temperature value. If after that
temperature value will not be updated to good one, we badly configure
tx power parameters and device is unable to send a data.

Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=35932

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agobluetooth l2cap: fix locking in l2cap_global_chan_by_psm
Johannes Berg [Wed, 1 Jun 2011 06:29:54 +0000]
bluetooth l2cap: fix locking in l2cap_global_chan_by_psm

read_lock() ... read_unlock_bh() is clearly bogus.
This was broken by

commit 23691d75cdc69c3b285211b4d77746aa20a17d18
Author: Gustavo F. Padovan <padovan@profusion.mobi>
Date:   Wed Apr 27 18:26:32 2011 -0300

    Bluetooth: Remove l2cap_sk_list

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoath9k: fix two more bugs in tx power
Daniel Halperin [Tue, 31 May 2011 18:59:30 +0000]
ath9k: fix two more bugs in tx power

This is the same fix as

   commit 841051602e3fa18ea468fe5a177aa92b6eb44b56
   Author: Matteo Croce <technoboy85@gmail.com>
   Date:   Fri Dec 3 02:25:08 2010 +0100

   The ath9k driver subtracts 3 dBm to the txpower as with two radios the
   signal power is doubled.
   The resulting value is assigned in an u16 which overflows and makes
   the card work at full power.

in two more places. I grepped the ath tree and didn't find any others.

Cc: stable@kernel.org
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agocfg80211: don't drop p2p probe responses
Eliad Peller [Sun, 29 May 2011 12:53:20 +0000]
cfg80211: don't drop p2p probe responses

Commit 0a35d36 ("cfg80211: Use capability info to detect mesh beacons")
assumed that probe response with both ESS and IBSS bits cleared
means that the frame was sent by a mesh sta.

However, these capabilities are also being used in the p2p_find phase,
and the mesh-validation broke it.

Rename the WLAN_CAPABILITY_IS_MBSS macro, and verify that mesh ies
exist before assuming this frame was sent by a mesh sta.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

8 years agoxen/blkback: potential null dereference in error handling
Dan Carpenter [Fri, 27 May 2011 06:27:16 +0000]
xen/blkback: potential null dereference in error handling

blkbk->pending_pages can be NULL here so I added a check for it.

Signed-off-by: Dan Carpenter <error27@gmail.com>
[v1: Redid the loop a bit]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

8 years agoxen/blkback: don't call vbd_size() if bd_disk is NULL
Laszlo Ersek [Wed, 25 May 2011 10:24:25 +0000]
xen/blkback: don't call vbd_size() if bd_disk is NULL

...because vbd_size() dereferences bd_disk if bd_part is NULL.

Signed-off-by: Laszlo Ersek<lersek@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

8 years agoMerge git://git.infradead.org/mtd-2.6
Linus Torvalds [Wed, 1 Jun 2011 12:47:39 +0000]
Merge git://git.infradead.org/mtd-2.6

* git://git.infradead.org/mtd-2.6:
  mtd: fix physmap.h warnings