12 years agoradeon: fix PCI bus mastering support enables.
Alex Deucher [Thu, 16 Oct 2008 23:21:45 +0000]
radeon: fix PCI bus mastering support enables.

Someone noticed these registers moved around for later chips,
so we redo the codepaths per-chip. PCIE chips don't appear to
require explicit enables.

Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoradeon: add RS400 family support.
Alex Deucher [Thu, 16 Oct 2008 23:19:33 +0000]
radeon: add RS400 family support.

This adds support for the RS400 family of IGPs for Intel CPUs.

Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm/radeon: add support for RS740 IGP chipsets.
Alex Deucher [Thu, 16 Oct 2008 07:12:02 +0000]
drm/radeon: add support for RS740 IGP chipsets.

This adds support for the HS2100 IGP chipset.

Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: GM45 has GM965-style MCH setup.
Eric Anholt [Wed, 15 Oct 2008 07:05:58 +0000]
i915: GM45 has GM965-style MCH setup.

Fixes tiling swizzling mode failures that manifest in glReadPixels().

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: Don't run retire work handler while suspended
Keith Packard [Wed, 15 Oct 2008 04:41:13 +0000]
i915: Don't run retire work handler while suspended

At leavevt and lastclose time, cancel any pending retire work handler
invocation, and keep the retire work handler from requeuing itself if it is
currently running.

This patch restructures i915_gem_idle to perform all of these tasks instead
of having both leavevt and lastclose call a sequence of functions.

Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: Map status page cached for chips with GTT-based HWS location.
Keith Packard [Wed, 15 Oct 2008 02:55:10 +0000]
i915: Map status page cached for chips with GTT-based HWS location.

This should improve performance by avoiding uncached reads by the CPU (the
point of having a status page), and may improve stability.  This patch only
affects G33, GM45 and G45 chips as those are the only ones using GTT-based
HWS mappings.

Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: Fix up ring initialization to cover G45 oddities
Keith Packard [Wed, 15 Oct 2008 00:20:35 +0000]
i915: Fix up ring initialization to cover G45 oddities

G45 appears quite sensitive to ring initialization register writes,
sometimes leaving the HEAD register with the START register contents. Check
to make sure HEAD is reset correctly when START is written, and fix it up,
screaming loudly.

Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: Use non-reserved status page index for breadcrumb
Keith Packard [Wed, 15 Oct 2008 00:19:38 +0000]
i915: Use non-reserved status page index for breadcrumb

Dwords 0 through 0x1f are reserved for use by the hardware. Move the GEM
breadcrumb from 0x10 to 0x20 to keep out of this area.

Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm: Increment dev_priv->irq_received so i915_gem_interrupts count works.
Eric Anholt [Mon, 6 Oct 2008 22:14:12 +0000]
drm: Increment dev_priv->irq_received so i915_gem_interrupts count works.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm: kill drm_device->irq
Jesse Barnes [Mon, 15 Sep 2008 22:00:33 +0000]
drm: kill drm_device->irq

Like the last patch but adds a macro to get at the irq value instead of
dereferencing pdev directly.  Should  make things easier for the BSD guys and
if we ever support non-PCI devices.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm: wbinvd is cache coherent.
Dave Airlie [Tue, 7 Oct 2008 03:41:49 +0000]
drm: wbinvd is cache coherent.

doing an ipi for the wbinvd case isn't necessary.

Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: add missing return in error path.
Dave Airlie [Tue, 7 Oct 2008 03:40:36 +0000]
i915: add missing return in error path.

Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: fixup permissions on gem ioctls.
Dave Airlie [Tue, 7 Oct 2008 03:40:10 +0000]
i915: fixup permissions on gem ioctls.

init/entervt/leavevt should be root-only master ioctls.

Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm: Clean up many sparse warnings in i915.
Eric Anholt [Thu, 2 Oct 2008 19:24:47 +0000]
drm: Clean up many sparse warnings in i915.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm: Use ioremap_wc in i915_driver instead of ioremap, since we always want WC.
Eric Anholt [Tue, 23 Sep 2008 21:50:57 +0000]
drm: Use ioremap_wc in i915_driver instead of ioremap, since we always want WC.

Fixes failure to map the ringbuffer when PAT tells us we don't get to do
uncached on something that's already mapped WC, or something along those lines.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm: G33-class hardware has a newer 965-style MCH (no DCC register).
Eric Anholt [Mon, 15 Sep 2008 20:13:34 +0000]
drm: G33-class hardware has a newer 965-style MCH (no DCC register).

Fixes bad software fallback rendering in Mesa in dual-channel configurations.

d9a2470012588dc5313a5ac8bb2f03575af00e99

Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm: Avoid oops in GEM execbuffers with bad arguments.
Eric Anholt [Wed, 10 Sep 2008 21:22:49 +0000]
drm: Avoid oops in GEM execbuffers with bad arguments.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoDRM: Return -EBADF on bad object in flink, and return curent name if it exists.
Eric Anholt [Tue, 9 Sep 2008 18:40:34 +0000]
DRM: Return -EBADF on bad object in flink, and return curent name if it exists.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915 gem: install and uninstall irq handler in entervt and leavevt ioctls.
Kristian Høgsberg [Wed, 20 Aug 2008 15:04:27 +0000]
i915 gem: install and uninstall irq handler in entervt and leavevt ioctls.

Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: Make use of sarea_priv conditional.
Kristian Høgsberg [Wed, 20 Aug 2008 15:20:13 +0000]
i915: Make use of sarea_priv conditional.

We fail ioctls that depend on the sarea_priv with EINVAL.

Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: Use struct_mutex to protect ring in GEM mode.
Eric Anholt [Mon, 1 Sep 2008 23:45:29 +0000]
i915: Use struct_mutex to protect ring in GEM mode.

In the conversion for GEM, we had stopped using the hardware lock to protect
ring usage, since it was all internal to the DRM now.  However, some paths
weren't converted to using struct_mutex to prevent multiple threads from
concurrently working on the ring, in particular between the vblank swap handler
and ioctls.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: Add chip set ID param.
Kristian Høgsberg [Wed, 20 Aug 2008 15:08:52 +0000]
i915: Add chip set ID param.

Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm: Add GEM ("graphics execution manager") to i915 driver.
Eric Anholt [Wed, 30 Jul 2008 19:06:12 +0000]
drm: Add GEM ("graphics execution manager") to i915 driver.

GEM allows the creation of persistent buffer objects accessible by the
graphics device through new ioctls for managing execution of commands on the
device.  The userland API is almost entirely driver-specific to ensure that
any driver building on this model can easily map the interface to individual
driver requirements.

GEM is used by the 2d driver for managing its internal state allocations and
will be used for pixmap storage to reduce memory consumption and enable
zero-copy GLX_EXT_texture_from_pixmap, and in the 3d driver is used to enable
GL_EXT_framebuffer_object and GL_ARB_pixel_buffer_object.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoExport kmap_atomic_pfn for DRM-GEM.
Eric Anholt [Thu, 21 Aug 2008 19:53:33 +0000]
Export kmap_atomic_pfn for DRM-GEM.

The driver would like to map IO space directly for copying data in when
appropriate, to avoid CPU cache flushing for streaming writes.
kmap_atomic_pfn lets us avoid IPIs associated with ioremap for this process.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoExport shmem_file_setup for DRM-GEM
Keith Packard [Fri, 20 Jun 2008 07:08:06 +0000]
Export shmem_file_setup for DRM-GEM

GEM needs to create shmem files to back buffer objects.  Though currently
creation of files for objects could have been driven from userland, the
modesetting work will require allocation of buffer objects before userland
is running, for boot-time message display.

Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: Nick Piggin <npiggin@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm: Rework vblank-wait handling to allow interrupt reduction.
Jesse Barnes [Tue, 30 Sep 2008 19:14:26 +0000]
drm: Rework vblank-wait handling to allow interrupt reduction.

Previously, drivers supporting vblank interrupt waits would run the interrupt
all the time, or all the time that any 3d client was running, preventing the
CPU from sleeping for long when the system was otherwise idle.  Now, interrupts
are disabled any time that no client is waiting on a vblank event. The new
method uses vblank counters on the chipsets when the interrupts are turned
off, rather than counting interrupts, so that we can continue to present
accurate vblank numbers.

Co-author: Michel Dänzer <michel@tungstengraphics.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm/cred: wrap task credential accesses in the drm driver.
David Howells [Tue, 2 Sep 2008 01:03:14 +0000]
drm/cred: wrap task credential accesses in the drm driver.

Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.

Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().

Change some task->e?[ug]id to task_e?[ug]id().  In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.

Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David Airlie <airlied@redhat.com>

12 years agonew chip name is GM45
Jesse Barnes [Mon, 25 Aug 2008 22:16:19 +0000]
new chip name is GM45

Author: Zhenyu Wang <zhenyu.z.wang@intel.com>

i915: official name for GM45 chipset

Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoseparate i915 suspend/resume functions into their own file
Jesse Barnes [Mon, 25 Aug 2008 22:11:06 +0000]
separate i915 suspend/resume functions into their own file

[Patch against drm-next.  Consider this a trial balloon for our new Linux
development model.]

This is a big chunk of code.  Separating it out makes it easier to change
without churn on the main i915_drv.c file (and there will be churn as we
fix bugs and add things like kernel mode setting).  Also makes it easier
to share this file with BSD.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoradeon: fix writeback across suspend/resume.
Dave Airlie [Tue, 2 Sep 2008 00:10:16 +0000]
radeon: fix writeback across suspend/resume.

Make writeback not get disabled on resume.

Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm: fix sysfs error path.
Dave Airlie [Tue, 2 Sep 2008 00:06:06 +0000]
drm: fix sysfs error path.

Pointed out by Roel Kluin on dri-devel.

Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoFB_SIS=m, DRM_SIS=y is not a legal configuration.
Adrian Bunk [Sun, 24 Aug 2008 07:11:22 +0000]
FB_SIS=m, DRM_SIS=y is not a legal configuration.

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoAdd Intel ACPI IGD OpRegion support
Matthew Garrett [Tue, 5 Aug 2008 18:37:25 +0000]
Add Intel ACPI IGD OpRegion support

This adds the support necessary for allowing ACPI backlight control to
work on some newer Intel-based graphics systems. Tested on Thinkpad T61
and HP 2510p hardware.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

12 years agoi915: Initialize hardware status page at device load when possible.
Keith Packard [Wed, 30 Jul 2008 20:03:43 +0000]
i915: Initialize hardware status page at device load when possible.

Some chips were unstable with repeated setup/teardown of the hardware status
page.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: Track progress inside of batchbuffers for determining wedgedness.
Keith Packard [Wed, 30 Jul 2008 19:21:20 +0000]
i915: Track progress inside of batchbuffers for determining wedgedness.

This avoids early termination for long-running commands.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: Add support for MSI and interrupt mitigation.
Eric Anholt [Tue, 29 Jul 2008 19:10:39 +0000]
i915: Add support for MSI and interrupt mitigation.

Previous attempts at interrupt mitigation had been foiled by i915_wait_irq's
failure to update the sarea seqno value when the status page indicated that
the seqno had already been passed.  MSI support has been seen to cut CPU
costs by up to 40% in some workloads by avoiding other expensive interrupt
handlers for frequent graphics interrupts.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: Use more consistent names for regs, and store them in a separate file.
Jesse Barnes [Tue, 29 Jul 2008 18:54:06 +0000]
i915: Use more consistent names for regs, and store them in a separate file.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: Ignore X server provided mmio address
Keith Packard [Wed, 30 Jul 2008 19:36:08 +0000]
i915: Ignore X server provided mmio address

It is already correctly detected by the kernel for use in suspend/resume.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoi915: remove settable use_mi_batchbuffer_start
Keith Packard [Wed, 30 Jul 2008 19:28:47 +0000]
i915: remove settable use_mi_batchbuffer_start

The driver can know what hardware requires MI_BATCH_BUFFER vs
MI_BATCH_BUFFER_START; there's no reason to let user mode configure this.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoSiS DRM: fix a pointer cast warning
David Howells [Wed, 30 Jul 2008 19:29:38 +0000]
SiS DRM: fix a pointer cast warning

Fix a pointer cast warning in the SIS DRM code.

This was introduced in patch ce65a44de07f73ceda1749812b75086b7add408d.

Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoSiS DRM: fix the memory allocator if the SIS FB is built as a module
David Howells [Wed, 30 Jul 2008 19:29:37 +0000]
SiS DRM: fix the memory allocator if the SIS FB is built as a module

Fix the SIS DRM memory allocator if the SIS FB built as a module.  The SIS DRM
code initialises the mm allocation hooks, but _only_ if the SIS FB is not
built as a module because it depends on CONFIG_FB_SIS, and that's unset if the
SIS FB is not built in.  It must check CONFIG_FB_SIS_MODULE as well.

Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agodrm: remove #define's for non-linux systems
Carlos R. Mafra [Wed, 30 Jul 2008 19:29:37 +0000]
drm: remove #define's for non-linux systems

There is no point in considering FreeBSD et al.  in the linux kernel
source code.

Signed-off-by: Carlos R. Mafra <crmafra@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

12 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6
Linus Torvalds [Fri, 17 Oct 2008 16:50:12 +0000]
Merge git://git./linux/kernel/git/gregkh/staging-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (25 commits)
  staging: at76_usb wireless driver
  Staging: workaround build system bug
  Staging: Lindent sxg.c
  Staging: SLICOSS: Call pci_release_regions at driver exit
  Staging: SLICOSS: Fix remaining type names
  Staging: SLICOSS: Fix warnings due to static usage
  Staging: SLICOSS: lots of checkpatch fixes
  Staging: go7007 v4l fixes
  Staging: Fix gcc warnings in sxg
  Staging: add echo cancelation module
  Staging: add wlan-ng prism2 usb driver
  Staging: add w35und wifi driver
  Staging: USB/IP: add host driver
  Staging: USB/IP: add client driver
  Staging: USB/IP: add common functions needed
  Staging: add the go7007 video driver
  Staging: add me4000 pci data collection driver
  Staging: add me4000 firmware files
  Staging: add sxg network driver
  Staging: add Alacritech slicoss network driver
  ...

Fixed up conflicts due to taint flags changes and MAINTAINERS cleanup in
MAINTAINERS, include/linux/kernel.h and kernel/panic.c.

12 years agoMerge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
Linus Torvalds [Fri, 17 Oct 2008 16:33:39 +0000]
Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (47 commits)
  hwmon: (adm1026) Prevent log spamming
  hwmon: (adm1026) Fix debug messages
  hwmon: (adm1029) Use mask for fan_div value
  hwmon: (adt7470) Add documentation
  hwmon: (ibmaem) Automatically load on IBM systems via DMI
  hwmon: (ibmpex) Automatically load on IBM systems via DMI
  hwmon: (w83781d) Use new style driver binding
  hwmon: (w83781d) Stop abusing struct i2c_client for ISA devices
  hwmon: (w83781d) Make ISA interface depend on CONFIG_ISA
  hwmon: (w83781d) Additional information about AS99127F PWM
  hwmon: (w83781d) Detect alias chips
  hwmon: (w83781d) Refactor beep enable handling
  hwmon: Drop dead links to old National Semiconductor chip datasheets
  hwmon: (w83791d) add support for thermal cruise mode
  hwmon: (w83791d) add pwm_enable support
  hwmon: (w83791d) add manual PWM support
  hwmon: (w83791d) fan 4/5 pins can also be used for gpio
  hwmon: (max1619) Use inline functions instead of macros
  hwmon: (it87) Fix thermal sensor type values
  hwmon: (lm78) Convert to a new-style i2c driver
  ...

12 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
Linus Torvalds [Fri, 17 Oct 2008 16:30:35 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: Fix debugfs_create_dir's error checking method for sound/soc/
  ALSA: ASoC: Convert playpaq_wm8510 to bulk route registration API
  ALSA: kernel docs: fix sound/core/ kernel-doc
  ALSA: Handle NULL jacks in snd_jack_report()
  ALSA: hda - Fix PCM type of Nvidia HDMI devices

12 years agoMerge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
Linus Torvalds [Fri, 17 Oct 2008 16:29:55 +0000]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: remove __generic_unplug_device() from exports
  block: move q->unplug_work initialization
  blktrace: pass zfcp driver data
  blktrace: add support for driver data
  block: fix current kernel-doc warnings
  block: only call ->request_fn when the queue is not stopped
  block: simplify string handling in elv_iosched_store()
  block: fix kernel-doc for blk_alloc_devt()
  block: fix nr_phys_segments miscalculation bug
  block: add partition attribute for partition number
  block: add BIG FAT WARNING to CONFIG_DEBUG_BLOCK_EXT_DEVT
  softirq: Add support for triggering softirq work on softirqs.

12 years agoMerge branch 'for-linus' of git://www.jni.nu/cris
Linus Torvalds [Fri, 17 Oct 2008 16:09:48 +0000]
Merge branch 'for-linus' of git://www.jni.nu/cris

* 'for-linus' of git://www.jni.nu/cris:
  CRIS: proper defconfig setup
  [CRIS] Rename boot-linkscripts and fix the path to them.

12 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Linus Torvalds [Fri, 17 Oct 2008 16:00:23 +0000]
Merge git://git./linux/kernel/git/jejb/scsi-misc-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (39 commits)
  [SCSI] sd: fix compile failure with CONFIG_BLK_DEV_INTEGRITY=n
  libiscsi: fix locking in iscsi_eh_device_reset
  libiscsi: check reason why we are stopping iscsi session to determine error value
  [SCSI] iscsi_tcp: return a descriptive error value during connection errors
  [SCSI] libiscsi: rename host reset to target reset
  [SCSI] iscsi class: fix endpoint id handling
  [SCSI] libiscsi: Support drivers initiating session removal
  [SCSI] libiscsi: fix data corruption when target has to resend data-in packets
  [SCSI] sd: Switch kernel printing level for DIF messages
  [SCSI] sd: Correctly handle all combinations of DIF and DIX
  [SCSI] sd: Always print actual protection_type
  [SCSI] sd: Issue correct protection operation
  [SCSI] scsi_error: fix target reset handling
  [SCSI] lpfc 8.2.8 v2 : Add statistical reporting control and additional fc vendor events
  [SCSI] lpfc 8.2.8 v2 : Add sysfs control of target queue depth handling
  [SCSI] lpfc 8.2.8 v2 : Revert target busy in favor of transport disrupted
  [SCSI] scsi_dh_alua: remove REQ_NOMERGE
  [SCSI] lpfc 8.2.8 : update driver version to 8.2.8
  [SCSI] lpfc 8.2.8 : Add MSI-X support
  [SCSI] lpfc 8.2.8 : Update driver to use new Host byte error code DID_TRANSPORT_DISRUPTED
  ...

12 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Fri, 17 Oct 2008 15:58:52 +0000]
Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
  ipv4: Add a missing rcu_assign_pointer() in routing cache.
  [netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
  xen-netfront: Avoid unaligned accesses to IP header
  lmc: copy_*_user under spinlock
  [netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA

12 years agohwmon: (adm1026) Prevent log spamming
Jean Delvare [Fri, 17 Oct 2008 15:51:20 +0000]
hwmon: (adm1026) Prevent log spamming

When debugging is enabled, the adm1026 driver currently logs the
message "Setting VID from GPIO11-15" 108 times each time you run
"sensors". Once should be enough.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>

12 years agohwmon: (adm1026) Fix debug messages
Jean Delvare [Fri, 17 Oct 2008 15:51:20 +0000]
hwmon: (adm1026) Fix debug messages

* Add missing new-line to one debug message.
* Remove leading colon from 3 debug messages.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>

12 years agohwmon: (adm1029) Use mask for fan_div value
Corentin Labbe [Fri, 17 Oct 2008 15:51:20 +0000]
hwmon: (adm1029) Use mask for fan_div value

This is my patch for testing correct values of fan div in adm1029 and
prevent a division by 0 for some (unlikely) register values.

Signed-off-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (adt7470) Add documentation
Darrick J. Wong [Fri, 17 Oct 2008 15:51:20 +0000]
hwmon: (adt7470) Add documentation

Add at least the bare minimum of documentation for this chip.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (ibmaem) Automatically load on IBM systems via DMI
Darrick J. Wong [Fri, 17 Oct 2008 15:51:19 +0000]
hwmon: (ibmaem) Automatically load on IBM systems via DMI

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (ibmpex) Automatically load on IBM systems via DMI
Darrick J. Wong [Fri, 17 Oct 2008 15:51:19 +0000]
hwmon: (ibmpex) Automatically load on IBM systems via DMI

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (w83781d) Use new style driver binding
Wolfgang Grandegger [Fri, 17 Oct 2008 15:51:19 +0000]
hwmon: (w83781d) Use new style driver binding

This patch modifies the w83781d driver to use new style driver binding.
Substantial code modifications are required to deal with the new
interface, especially legacy device detection.

[JD: largely edited to make the patch smaller and to get the driver
to work again on ISA devices.]

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (w83781d) Stop abusing struct i2c_client for ISA devices
Jean Delvare [Fri, 17 Oct 2008 15:51:19 +0000]
hwmon: (w83781d) Stop abusing struct i2c_client for ISA devices

Upcoming changes to the I2C part of the w83781d driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>

12 years agohwmon: (w83781d) Make ISA interface depend on CONFIG_ISA
Wolfgang Grandegger [Fri, 17 Oct 2008 15:51:18 +0000]
hwmon: (w83781d) Make ISA interface depend on CONFIG_ISA

Probing the ISA bus on systems without ISA bus may hang the system.
This patch makes the ISA bus related code depend on the kernel
configuration parameter CONFIG_ISA. It moves ISA bus related code
into one #ifdef CONFIG_ISA ... #endif block and adds some helper
function.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (w83781d) Additional information about AS99127F PWM
Jean Delvare [Fri, 17 Oct 2008 15:51:18 +0000]
hwmon: (w83781d) Additional information about AS99127F PWM

This information was provided in lm-sensors ticket #2350:
http://www.lm-sensors.org/ticket/2350

This is IMHO still not enough to be able to safely implement fan
control support for the AS99127F, but this is valuable information so
I am adding it to the documentation.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (w83781d) Detect alias chips
Jean Delvare [Fri, 17 Oct 2008 15:51:18 +0000]
hwmon: (w83781d) Detect alias chips

The W83781D and W83782D can be accessed either on the I2C bus or the
ISA bus. We must not access the same chip through both interfaces. So
far we were relying on the user passing the correct ignore parameter
to skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the w83781d
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.

So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>

12 years agohwmon: (w83781d) Refactor beep enable handling
Jean Delvare [Fri, 17 Oct 2008 15:51:18 +0000]
hwmon: (w83781d) Refactor beep enable handling

We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>

12 years agohwmon: Drop dead links to old National Semiconductor chip datasheets
Jean Delvare [Fri, 17 Oct 2008 15:51:17 +0000]
hwmon: Drop dead links to old National Semiconductor chip datasheets

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (w83791d) add support for thermal cruise mode
Marc Hulsman [Fri, 17 Oct 2008 15:51:17 +0000]
hwmon: (w83791d) add support for thermal cruise mode

Add support to set target temperature and tolerance for thermal
cruise mode.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (w83791d) add pwm_enable support
Marc Hulsman [Fri, 17 Oct 2008 15:51:17 +0000]
hwmon: (w83791d) add pwm_enable support

Add support for pwm_enable.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (w83791d) add manual PWM support
Marc Hulsman [Fri, 17 Oct 2008 15:51:17 +0000]
hwmon: (w83791d) add manual PWM support

Add PWM manual control.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (w83791d) fan 4/5 pins can also be used for gpio
Marc Hulsman [Fri, 17 Oct 2008 15:51:16 +0000]
hwmon: (w83791d) fan 4/5 pins can also be used for gpio

Pins fan/pwm 4-5 can be in use as GPIO. If that is the case, do not
create their sysfs-interface.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (max1619) Use inline functions instead of macros
Andrew Morton [Fri, 17 Oct 2008 15:51:16 +0000]
hwmon: (max1619) Use inline functions instead of macros

Macros evaluating their arguments more than once are evil.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (it87) Fix thermal sensor type values
Jean Delvare [Fri, 17 Oct 2008 15:51:16 +0000]
hwmon: (it87) Fix thermal sensor type values

The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.

Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>

12 years agohwmon: (lm78) Convert to a new-style i2c driver
Jean Delvare [Fri, 17 Oct 2008 15:51:16 +0000]
hwmon: (lm78) Convert to a new-style i2c driver

The new-style lm78 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm78) Stop abusing struct i2c_client for ISA devices
Jean Delvare [Fri, 17 Oct 2008 15:51:15 +0000]
hwmon: (lm78) Stop abusing struct i2c_client for ISA devices

Upcoming changes to the I2C part of the lm78 driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm78) Prevent misdetection of Winbond chips
Jean Delvare [Fri, 17 Oct 2008 15:51:15 +0000]
hwmon: (lm78) Prevent misdetection of Winbond chips

The LM78 detection is relatively weak, and sometimes recent Winbond
chips can be misdetected as an LM78. We have had repeated reports of
this happening. We have an explicit check against this for the ISA
access, do the same for I2C access now.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm78) Detect alias chips
Jean Delvare [Fri, 17 Oct 2008 15:51:15 +0000]
hwmon: (lm78) Detect alias chips

The LM78 and LM79 can be accessed either on the I2C bus or the ISA
bus. We must not access the same chip through both interfaces. So far
we were relying on the user passing the correct ignore parameter to
skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the lm78
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.

So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm78) Fix I/O resource conflict with PNP
Jean Delvare [Fri, 17 Oct 2008 15:51:15 +0000]
hwmon: (lm78) Fix I/O resource conflict with PNP

Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.

Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource make the request
(and thus the detection) fail.

This is the exact same fix that was applied to driver w83781d in
March 2008 to address the same problem:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=2961cb22ef02850d90e7a12c28a14d74e327df8d

Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm85) Better label names
Jean Delvare [Fri, 17 Oct 2008 15:51:14 +0000]
hwmon: (lm85) Better label names

Label names ERROR1 and ERROR3 aren't exactly explicit. Change them for
better names that indicate what we are up to.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

12 years agohwmon: (lm85) Simplify RANGE_TO_REG
Jean Delvare [Fri, 17 Oct 2008 15:51:14 +0000]
hwmon: (lm85) Simplify RANGE_TO_REG

Function RANGE_TO_REG can easily be simplified. Credits go to Herbert
Poetzl for indirectly suggesting this to me. I tested that the new
implementation returns the same result as the original implementation
for all input values.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

12 years agohwmon: (lm85) Convert to a new-style i2c driver
Jean Delvare [Fri, 17 Oct 2008 15:51:14 +0000]
hwmon: (lm85) Convert to a new-style i2c driver

The new-style lm85 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

12 years agohwmon: (lm85) Support different PWM frequency tables
Jean Delvare [Fri, 17 Oct 2008 15:51:14 +0000]
hwmon: (lm85) Support different PWM frequency tables

The Analog Devices and SMSC devices supported by the lm85 driver do
not have the same PWM frequency table as the National Semiconductor
devices. Add support for per-device frequency tables.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

12 years agohwmon: (lm85) Select the closest PWM frequency
Jean Delvare [Fri, 17 Oct 2008 15:51:13 +0000]
hwmon: (lm85) Select the closest PWM frequency

The LM85 and compatible chips only support 8 arbitrary PWM frequencies.
The algorithm to pick one of them based on the user input is not
optimum. Improve it to always pick the closest supported frequency.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

12 years agohwmon: (lm85) Implement the standard PWM frequency interface
Jean Delvare [Fri, 17 Oct 2008 15:51:13 +0000]
hwmon: (lm85) Implement the standard PWM frequency interface

Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

12 years agohwmon: (lm85) Rework the device detection
Jean Delvare [Fri, 17 Oct 2008 15:51:13 +0000]
hwmon: (lm85) Rework the device detection

Rework the device detection to make it clearer and faster in the
general case (when a known device is found.)

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

12 years agohwmon: (ams) Simplify IRQ handling routine
Dmitry Torokhov [Fri, 17 Oct 2008 15:51:13 +0000]
hwmon: (ams) Simplify IRQ handling routine

Simplify the IRQ handling routine of ams driver.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (ams) Fix locking issues
Dmitry Torokhov [Fri, 17 Oct 2008 15:51:12 +0000]
hwmon: (ams) Fix locking issues

Use a separate mutex to serialize input device creation/removal,
otheriwse we deadlock if we try to remove input device while it is
being polled. Also do not take ams_info.lock when it is not needed.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (ams) Fix permissions on 'joystick' module parameter
Dmitry Torokhov [Fri, 17 Oct 2008 15:51:12 +0000]
hwmon: (ams) Fix permissions on 'joystick' module parameter

We should not allow writes to the 'joystick' module parameters since
writing there will not trigger creation of the input device. Disable
writes since we provide alternative way of enabling input device via
AMS device's sysfs attribute.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (ams) Convert to a new-style i2c driver
Jean Delvare [Fri, 17 Oct 2008 15:51:12 +0000]
hwmon: (ams) Convert to a new-style i2c driver

The legacy i2c binding model is phasing out, so the ams driver needs
to be converted to a new-style i2c driver. Here is a naive approach of
this conversion. Basically it is moving the i2c device creation from
the ams driver to the i2c-powermac driver. This should work, but I
suspect we could come up with something cleaner by declaring the i2c
device as part of the platform setup. This could be done later by
someone more familiar with openfirmware-based platforms than I am
myself.

One nice thing brought by this conversion is that the ams driver
should be loaded automatically on systems where is is needed (at
least when the I2C interface to the chip is used) providing
coldplug-aware user-space environment.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>

12 years agohwmon: (lm87) Add support for configuration through platform_data
Ben Hutchings [Fri, 17 Oct 2008 15:51:12 +0000]
hwmon: (lm87) Add support for configuration through platform_data

The lm87 driver normally assumes that firmware configured the chip
correctly.  Since this is not always the case, alllow platform code to
set the channel register value via platform_data.  All other
configuration registers can be changed after driver initialisation.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm87) Restore original configuration register on removal
Ben Hutchings [Fri, 17 Oct 2008 15:51:11 +0000]
hwmon: (lm87) Restore original configuration register on removal

This means that if we have to start the monitor when probed, we also
stop it on removal.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm87) Fix masking of config register in lm87_init_client()
Ben Hutchings [Fri, 17 Oct 2008 15:51:11 +0000]
hwmon: (lm87) Fix masking of config register in lm87_init_client()

lm87_init_client() conditionally sets the Start bit and clears the
INT#_Clear bit in the Config 1 register.  The condition should be that
either of these bits needs changing, but currently it checks the
(self-clearing) Initialization bit instead of INT#_Clear.

Fix the condition and also ensure we never set the Initialization bit.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm90) Don't spam the kernel log
Jean Delvare [Fri, 17 Oct 2008 15:51:11 +0000]
hwmon: (lm90) Don't spam the kernel log

Degrade the "Unsupported chip" message from info to debug level.
There's nothing wrong with this, so no need to bother the user.
Also make the message slightly more descriptive.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>

12 years agohwmon: (lm90) Support MAX6646, MAX6647 and MAX6649
Ben Hutchings [Fri, 17 Oct 2008 15:51:11 +0000]
hwmon: (lm90) Support MAX6646, MAX6647 and MAX6649

These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

12 years agohwmon: (lm90) Rename temperature conversion functions to match usage
Ben Hutchings [Fri, 17 Oct 2008 15:51:10 +0000]
hwmon: (lm90) Rename temperature conversion functions to match usage

The encoding of temperatures varies between chips and modes.  So do not
use "temp1" or "temp2" in the names of the conversion functions, but
specify the encoding.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>

12 years agohwmon: (lm90) Support ADT7461 in extended mode
Nate Case [Fri, 17 Oct 2008 15:51:10 +0000]
hwmon: (lm90) Support ADT7461 in extended mode

Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC.  Adjust the
register conversion functions accordingly.

Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>

12 years agohwmon: (lm90) Convert some macros to static functions
Nate Case [Fri, 17 Oct 2008 15:51:10 +0000]
hwmon: (lm90) Convert some macros to static functions

Use static functions instead of the TEMPx_FROM_REG* and TEMPx_TO_REG*
macros.  This will ensure type safety and eliminate any side effects
from arguments passed in since the macros referenced 'val' multiple
times.  This change should not affect functionality.

Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>

12 years agohwmon: (lm90) Update datasheet links
Jean Delvare [Fri, 17 Oct 2008 15:51:10 +0000]
hwmon: (lm90) Update datasheet links

Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>

12 years agohwmon: (lm90) Don't access nonexistent registers on Maxim chips
Jean Delvare [Fri, 17 Oct 2008 15:51:09 +0000]
hwmon: (lm90) Don't access nonexistent registers on Maxim chips

The Maxim chips supported by the lm90 driver have 8-bit high and low
remote limit values, not 11-bit as the other chips have. So stop reading
from and writing to registers that do not exist on these chips. Also
round the limit values set by the user properly.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>

12 years agohwmon: (lm90) Support the extra resolution bits of MAX6657
Jean Delvare [Fri, 17 Oct 2008 15:51:09 +0000]
hwmon: (lm90) Support the extra resolution bits of MAX6657

The Maxim MAX6657, MAX6658 and MAX6659 have extra resolution bits for
the local temperature measurement. Let the lm90 driver read them and
export them to user-space.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>

12 years agohwmon: (lm90) Move 16-bit value read to a separate function
Jean Delvare [Fri, 17 Oct 2008 15:51:09 +0000]
hwmon: (lm90) Move 16-bit value read to a separate function

Move the code which aggregates two 8-bit register values into a 16-bit
value to a separate function. We'll need to do it a second time soon and
I don't want to duplicate the code.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>

12 years agoMerge branch 'topic/asoc' into for-linus
Takashi Iwai [Fri, 17 Oct 2008 15:24:23 +0000]
Merge branch 'topic/asoc' into for-linus

12 years agoALSA: Fix debugfs_create_dir's error checking method for sound/soc/
Zhaolei [Fri, 17 Oct 2008 13:04:55 +0000]
ALSA: Fix debugfs_create_dir's error checking method for sound/soc/

debugfs_create_dir() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.

Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

12 years agoMerge branches 'topic/asoc', 'topic/hda' and 'topic/misc-fixes' into for-linus
Takashi Iwai [Fri, 17 Oct 2008 14:28:20 +0000]
Merge branches 'topic/asoc', 'topic/hda' and 'topic/misc-fixes' into for-linus

12 years agoblock: remove __generic_unplug_device() from exports
Jens Axboe [Fri, 17 Oct 2008 12:03:08 +0000]
block: remove __generic_unplug_device() from exports

The only out-of-core user is IDE, and that should be using
blk_start_queueing() instead.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>