11 years agommu-notifiers: core
Andrea Arcangeli [Mon, 28 Jul 2008 22:46:29 +0000]
mmu-notifiers: core

With KVM/GFP/XPMEM there isn't just the primary CPU MMU pointing to pages.
 There are secondary MMUs (with secondary sptes and secondary tlbs) too.
sptes in the kvm case are shadow pagetables, but when I say spte in
mmu-notifier context, I mean "secondary pte".  In GRU case there's no
actual secondary pte and there's only a secondary tlb because the GRU
secondary MMU has no knowledge about sptes and every secondary tlb miss
event in the MMU always generates a page fault that has to be resolved by
the CPU (this is not the case of KVM where the a secondary tlb miss will
walk sptes in hardware and it will refill the secondary tlb transparently
to software if the corresponding spte is present).  The same way
zap_page_range has to invalidate the pte before freeing the page, the spte
(and secondary tlb) must also be invalidated before any page is freed and
reused.

Currently we take a page_count pin on every page mapped by sptes, but that
means the pages can't be swapped whenever they're mapped by any spte
because they're part of the guest working set.  Furthermore a spte unmap
event can immediately lead to a page to be freed when the pin is released
(so requiring the same complex and relatively slow tlb_gather smp safe
logic we have in zap_page_range and that can be avoided completely if the
spte unmap event doesn't require an unpin of the page previously mapped in
the secondary MMU).

The mmu notifiers allow kvm/GRU/XPMEM to attach to the tsk->mm and know
when the VM is swapping or freeing or doing anything on the primary MMU so
that the secondary MMU code can drop sptes before the pages are freed,
avoiding all page pinning and allowing 100% reliable swapping of guest
physical address space.  Furthermore it avoids the code that teardown the
mappings of the secondary MMU, to implement a logic like tlb_gather in
zap_page_range that would require many IPI to flush other cpu tlbs, for
each fixed number of spte unmapped.

To make an example: if what happens on the primary MMU is a protection
downgrade (from writeable to wrprotect) the secondary MMU mappings will be
invalidated, and the next secondary-mmu-page-fault will call
get_user_pages and trigger a do_wp_page through get_user_pages if it
called get_user_pages with write=1, and it'll re-establishing an updated
spte or secondary-tlb-mapping on the copied page.  Or it will setup a
readonly spte or readonly tlb mapping if it's a guest-read, if it calls
get_user_pages with write=0.  This is just an example.

This allows to map any page pointed by any pte (and in turn visible in the
primary CPU MMU), into a secondary MMU (be it a pure tlb like GRU, or an
full MMU with both sptes and secondary-tlb like the shadow-pagetable layer
with kvm), or a remote DMA in software like XPMEM (hence needing of
schedule in XPMEM code to send the invalidate to the remote node, while no
need to schedule in kvm/gru as it's an immediate event like invalidating
primary-mmu pte).

At least for KVM without this patch it's impossible to swap guests
reliably.  And having this feature and removing the page pin allows
several other optimizations that simplify life considerably.

Dependencies:

1) mm_take_all_locks() to register the mmu notifier when the whole VM
   isn't doing anything with "mm".  This allows mmu notifier users to keep
   track if the VM is in the middle of the invalidate_range_begin/end
   critical section with an atomic counter incraese in range_begin and
   decreased in range_end.  No secondary MMU page fault is allowed to map
   any spte or secondary tlb reference, while the VM is in the middle of
   range_begin/end as any page returned by get_user_pages in that critical
   section could later immediately be freed without any further
   ->invalidate_page notification (invalidate_range_begin/end works on
   ranges and ->invalidate_page isn't called immediately before freeing
   the page).  To stop all page freeing and pagetable overwrites the
   mmap_sem must be taken in write mode and all other anon_vma/i_mmap
   locks must be taken too.

2) It'd be a waste to add branches in the VM if nobody could possibly
   run KVM/GRU/XPMEM on the kernel, so mmu notifiers will only enabled if
   CONFIG_KVM=m/y.  In the current kernel kvm won't yet take advantage of
   mmu notifiers, but this already allows to compile a KVM external module
   against a kernel with mmu notifiers enabled and from the next pull from
   kvm.git we'll start using them.  And GRU/XPMEM will also be able to
   continue the development by enabling KVM=m in their config, until they
   submit all GRU/XPMEM GPLv2 code to the mainline kernel.  Then they can
   also enable MMU_NOTIFIERS in the same way KVM does it (even if KVM=n).
   This guarantees nobody selects MMU_NOTIFIER=y if KVM and GRU and XPMEM
   are all =n.

The mmu_notifier_register call can fail because mm_take_all_locks may be
interrupted by a signal and return -EINTR.  Because mmu_notifier_reigster
is used when a driver startup, a failure can be gracefully handled.  Here
an example of the change applied to kvm to register the mmu notifiers.
Usually when a driver startups other allocations are required anyway and
-ENOMEM failure paths exists already.

 struct  kvm *kvm_arch_create_vm(void)
 {
        struct kvm *kvm = kzalloc(sizeof(struct kvm), GFP_KERNEL);
+       int err;

        if (!kvm)
                return ERR_PTR(-ENOMEM);

        INIT_LIST_HEAD(&kvm->arch.active_mmu_pages);

+       kvm->arch.mmu_notifier.ops = &kvm_mmu_notifier_ops;
+       err = mmu_notifier_register(&kvm->arch.mmu_notifier, current->mm);
+       if (err) {
+               kfree(kvm);
+               return ERR_PTR(err);
+       }
+
        return kvm;
 }

mmu_notifier_unregister returns void and it's reliable.

The patch also adds a few needed but missing includes that would prevent
kernel to compile after these changes on non-x86 archs (x86 didn't need
them by luck).

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix mm/filemap_xip.c build]
[akpm@linux-foundation.org: fix mm/mmu_notifier.c build]
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kanoj Sarcar <kanojsarcar@yahoo.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Chris Wright <chrisw@redhat.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Izik Eidus <izike@qumranet.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agommu-notifiers: add mm_take_all_locks() operation
Andrea Arcangeli [Mon, 28 Jul 2008 22:46:26 +0000]
mmu-notifiers: add mm_take_all_locks() operation

mm_take_all_locks holds off reclaim from an entire mm_struct.  This allows
mmu notifiers to register into the mm at any time with the guarantee that
no mmu operation is in progress on the mm.

This operation locks against the VM for all pte/vma/mm related operations
that could ever happen on a certain mm.  This includes vmtruncate,
try_to_unmap, and all page faults.

The caller must take the mmap_sem in write mode before calling
mm_take_all_locks().  The caller isn't allowed to release the mmap_sem
until mm_drop_all_locks() returns.

mmap_sem in write mode is required in order to block all operations that
could modify pagetables and free pages without need of altering the vma
layout (for example populate_range() with nonlinear vmas).  It's also
needed in write mode to avoid new anon_vmas to be associated with existing
vmas.

A single task can't take more than one mm_take_all_locks() in a row or it
would deadlock.

mm_take_all_locks() and mm_drop_all_locks are expensive operations that
may have to take thousand of locks.

mm_take_all_locks() can fail if it's interrupted by signals.

When mmu_notifier_register returns, we must be sure that the driver is
notified if some task is in the middle of a vmtruncate for the 'mm' where
the mmu notifier was registered (mmu_notifier_invalidate_range_start/end
is run around the vmtruncation but mmu_notifier_register can run after
mmu_notifier_invalidate_range_start and before
mmu_notifier_invalidate_range_end).  Same problem for rmap paths.  And
we've to remove page pinning to avoid replicating the tlb_gather logic
inside KVM (and GRU doesn't work well with page pinning regardless of
needing tlb_gather), so without mm_take_all_locks when vmtruncate frees
the page, kvm would have no way to notice that it mapped into sptes a page
that is going into the freelist without a chance of any further
mmu_notifier notification.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kanoj Sarcar <kanojsarcar@yahoo.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Chris Wright <chrisw@redhat.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Izik Eidus <izike@qumranet.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agommu-notifiers: add list_del_init_rcu()
Andrea Arcangeli [Mon, 28 Jul 2008 22:46:22 +0000]
mmu-notifiers: add list_del_init_rcu()

Introduce list_del_init_rcu() and document it.

Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kanoj Sarcar <kanojsarcar@yahoo.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Chris Wright <chrisw@redhat.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Izik Eidus <izike@qumranet.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoarm: fix HAVE_CLK merge goof
David Brownell [Mon, 28 Jul 2008 22:46:22 +0000]
arm: fix HAVE_CLK merge goof

This fixes a merge goof whereby ARCH_EP93XX got the "select HAVE_CLK" line
which belongs instead with ARCH_AT91.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years ago__ratelimit() cpu flags can't be static
Alexey Dobriyan [Mon, 28 Jul 2008 22:46:21 +0000]
__ratelimit() cpu flags can't be static

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agotmpfs: fix kernel BUG in shmem_delete_inode
Hugh Dickins [Mon, 28 Jul 2008 22:46:19 +0000]
tmpfs: fix kernel BUG in shmem_delete_inode

SuSE's insserve initscript ordering program hits kernel BUG at mm/shmem.c:814
on 2.6.26.  It's using posix_fadvise on directories, and the shmem_readpage
method added in 2.6.23 is letting POSIX_FADV_WILLNEED allocate useless pages
to a tmpfs directory, incrementing i_blocks count but never decrementing it.

Fix this by assigning shmem_aops (pointing to readpage and writepage and
set_page_dirty) only when it's needed, on a regular file or a long symlink.

Many thanks to Kel for outstanding bugreport and steps to reproduce it.

Reported-by: Kel Modderman <kel@otaku42.de>
Tested-by: Kel Modderman <kel@otaku42.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoexec: include pagemap.h again to fix build
Hugh Dickins [Mon, 28 Jul 2008 22:46:18 +0000]
exec: include pagemap.h again to fix build

Fix compilation errors on avr32 and without CONFIG_SWAP, introduced by
ba92a43dbaee339cf5915ef766d3d3ffbaaf103c ("exec: remove some includes")

  In file included from include/asm/tlb.h:24,
                   from fs/exec.c:55:
  include/asm-generic/tlb.h: In function 'tlb_flush_mmu':
  include/asm-generic/tlb.h:76: error: implicit declaration of function 'release_pages'
  include/asm-generic/tlb.h: In function 'tlb_remove_page':
  include/asm-generic/tlb.h:105: error: implicit declaration of function 'page_cache_release'
  make[1]: *** [fs/exec.o] Error 1

This straightforward part-revert is nobody's favourite patch to address
the underlying tlb.h needs swap.h needs pagemap.h (but sparc won't like
that) mess; but appropriate to fix the build now before any overhaul.

Reported-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Reported-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Tested-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoMerge branch 'cpus4096-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux...
Linus Torvalds [Mon, 28 Jul 2008 22:13:42 +0000]
Merge branch 'cpus4096-v2' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'cpus4096-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  cpu masks: optimize and clean up cpumask_of_cpu()
  cpumask: export cpumask_of_cpu_map
  cpumask: change cpumask_of_cpu_ptr to use new cpumask_of_cpu
  cpumask: put cpumask_of_cpu_map in the initdata section
  cpumask: make cpumask_of_cpu_map generic

11 years agoipwireless: fix compile failure
James Bottomley [Mon, 28 Jul 2008 22:11:44 +0000]
ipwireless: fix compile failure

There's a brown paper bag compile failure introduced by this patch

commit a01386924874c4d6d67f8a34e66f04452c2abb69
Author: David Sterba <dsterba@suse.cz>
Date:   Mon Jul 28 16:53:32 2008 +0200

    ipwireless: Preallocate received packet buffers with MRU size

Really, it can't ever have been even compile tested.  It looks like the
closing bracket is in the wrong place, so this is the fix.

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoMerge branch 'linus' into cpus4096
Ingo Molnar [Mon, 28 Jul 2008 21:32:00 +0000]
Merge branch 'linus' into cpus4096

Conflicts:

kernel/stop_machine.c

Signed-off-by: Ingo Molnar <mingo@elte.hu>

11 years agocpu masks: optimize and clean up cpumask_of_cpu()
Linus Torvalds [Mon, 28 Jul 2008 18:32:33 +0000]
cpu masks: optimize and clean up cpumask_of_cpu()

Clean up and optimize cpumask_of_cpu(), by sharing all the zero words.

Instead of stupidly generating all possible i=0...NR_CPUS 2^i patterns
creating a huge array of constant bitmasks, realize that the zero words
can be shared.

In other words, on a 64-bit architecture, we only ever need 64 of these
arrays - with a different bit set in one single world (with enough zero
words around it so that we can create any bitmask by just offsetting in
that big array). And then we just put enough zeroes around it that we
can point every single cpumask to be one of those things.

So when we have 4k CPU's, instead of having 4k arrays (of 4k bits each,
with one bit set in each array - 2MB memory total), we have exactly 64
arrays instead, each 8k bits in size (64kB total).

And then we just point cpumask(n) to the right position (which we can
calculate dynamically). Once we have the right arrays, getting
"cpumask(n)" ends up being:

  static inline const cpumask_t *get_cpu_mask(unsigned int cpu)
  {
          const unsigned long *p = cpu_bit_bitmap[1 + cpu % BITS_PER_LONG];
          p -= cpu / BITS_PER_LONG;
          return (const cpumask_t *)p;
  }

This brings other advantages and simplifications as well:

 - we are not wasting memory that is just filled with a single bit in
   various different places

 - we don't need all those games to re-create the arrays in some dense
   format, because they're already going to be dense enough.

if we compile a kernel for up to 4k CPU's, "wasting" that 64kB of memory
is a non-issue (especially since by doing this "overlapping" trick we
probably get better cache behaviour anyway).

[ mingo@elte.hu:

  Converted Linus's mails into a commit. See:

     http://lkml.org/lkml/2008/7/27/156
     http://lkml.org/lkml/2008/7/28/320

  Also applied a family filter - which also has the side-effect of leaving
  out the bits where Linus calls me an idio... Oh, never mind ;-)
]

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

11 years agoMerge branch 'linus' into cpus4096
Ingo Molnar [Mon, 28 Jul 2008 19:14:43 +0000]
Merge branch 'linus' into cpus4096

11 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Linus Torvalds [Mon, 28 Jul 2008 16:59:26 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: add driver for Atmel integrated touchscreen controller
  Input: ads7846 - optimize order of calculating Rt in ads7846_rx()
  Input: ads7846 - fix sparse endian warnings
  Input: uinput - remove duplicate include
  Input: serio - offload resume to kseriod
  Input: serio - mark serio_register_driver() __must_check

11 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm
Linus Torvalds [Mon, 28 Jul 2008 16:46:00 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/teigland/dlm

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
  dlm: fix uninitialized variable for search_rsb_list callers
  dlm: release socket on error
  dlm: fix basts for granted CW waiting PR/CW
  dlm: check for null in device_write

11 years agoMerge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Linus Torvalds [Mon, 28 Jul 2008 16:05:35 +0000]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
  powerpc: Disable 64K hugetlb support when doing 64K SPU mappings
  powerpc/powermac: Fixup default serial port device for pmac_zilog
  powerpc/powermac: Use sane default baudrate for SCC debugging
  powerpc/mm: Implement _PAGE_SPECIAL & pte_special() for 64-bit
  powerpc: Show processor cache information in sysfs
  powerpc: Make core id information available to userspace
  powerpc: Make core sibling information available to userspace
  powerpc/vio: More fallout from dma_mapping_error API change
  ibmveth: Fix multiple errors with dma_mapping_error conversion
  powerpc/pseries: Fix CMO sysdev attribute API change fallout
  powerpc: Enable tracehook for the architecture
  powerpc: Add TIF_NOTIFY_RESUME support for tracehook
  powerpc: Add asm/syscall.h with the tracehook entry points
  powerpc: Make syscall tracing use tracehook.h helpers
  powerpc: Call tracehook_signal_handler() when setting up signal frames
  powerpc: Update cpu_sibling_maps dynamically
  powerpc: register_cpu_online should be __cpuinit
  powerpc: kill useless SMT code in prom_hold_cpus
  powerpc: Fix 8xx build failure
  powerpc: Fix vio build warnings
  ...

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/ISDN-2.6
Linus Torvalds [Mon, 28 Jul 2008 15:41:56 +0000]
Merge git://git./linux/kernel/git/kkeil/ISDN-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/ISDN-2.6:
  Remove deprecated virt_to_bus()

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
Linus Torvalds [Mon, 28 Jul 2008 15:41:13 +0000]
Merge git://git./linux/kernel/git/lethal/sh-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (72 commits)
  sh: SuperH Mobile CEU and camera platform data for AP325RXA
  sh: Update smc911x platform data for AP325RXA
  sh: SuperH Mobile LCDC platform data for AP325RXA
  sh: Add SuperH Mobile CEU platform data for Migo-R
  sh: Add SuperH Mobile LCDC platform data for Migo-R
  sh: Move asid_cache() out of ifdef to fix SH-3/4 nommu build.
  sh: Workaround for __put_user_asm() bug with gcc 4.x on big-endian.
  sh: Wire up new syscalls.
  sh: fix uImage Entry Point
  sh_keysc: remove request_mem_region() and release_mem_region()
  sh: Don't miss pending signals returning to user mode after signal processing
  sh: Use clk_always_enable() on sh7366
  sh: Use clk_always_enable() on sh7343 / SE77343
  sh: Use clk_always_enable() on sh7722 / Migo-R / SE7722
  sh: Use clk_always_enable() on sh7723 / ap325rxa
  sh: Introduce clk_always_enable() function
  sh: Show all clocks and their state in /proc/clocks
  sh: Merge sh7343 and sh7722 clock code
  sh: Add SuperH Mobile MSTPCR bits to clock framework
  sh: Use arch_flags to simplify sh7722 siu clock code
  ...

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus
Linus Torvalds [Mon, 28 Jul 2008 15:37:46 +0000]
Merge git://git./linux/kernel/git/rusty/linux-2.6-for-linus

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  stop_machine: fix up ftrace.c
  stop_machine: Wean existing callers off stop_machine_run()
  stop_machine(): stop_machine_run() changed to use cpu mask
  Hotplug CPU: don't check cpu_online after take_cpu_down
  Simplify stop_machine
  stop_machine: add ALL_CPUS option
  module: fix build warning with !CONFIG_KALLSYMS

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
Linus Torvalds [Mon, 28 Jul 2008 15:35:40 +0000]
Merge git://git./linux/kernel/git/mchehab/v4l-dvb

* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (98 commits)
  V4L/DVB (8549): mxl5007: Fix an error at include file
  V4L/DVB (8548): pwc: Fix compilation
  V4L/DVB (8546): add tuner-3036 and dpc7146 drivers to feature-removal-schedule.txt
  V4L/DVB (8546): saa7146: fix read from uninitialized memory
  V4L/DVB (8544): gspca: probe/open race.
  V4L/DVB (8543): em28xx: Rename #define for Compro VideoMate ForYou/Stereo
  V4L/DVB (8542): em28xx: AMD ATI TV Wonder HD 600 entry at cards struct is duplicated
  V4L/DVB (8541): em28xx: HVR-950 entry is duplicated.
  V4L/DVB (8540): em28xx-cards: Add Compro VideoMate ForYou/Stereo model
  V4L/DVB (8539): em28xx-cards: New supported IDs for analog models
  V4L/DVB (8538): em28xx-cards: Add GrabBeeX+ USB2800 model
  V4L/DVB (8534): remove select's of FW_LOADER
  V4L/DVB (8522): videodev2: Fix merge conflict
  V4L/DVB (8532): mxl5007t: remove excessive locks
  V4L/DVB (8531): mxl5007t: move i2c gate handling outside of mutex protected code blocks
  V4L/DVB (8530): au0828: add support for new revision of HVR950Q
  V4L/DVB (8529): mxl5007t: enable _init and _sleep power management functionality
  V4L/DVB (8528): add support for MaxLinear MxL5007T silicon tuner
  V4L/DVB (8526): saa7146: fix VIDIOC_ENUM_FMT
  V4L/DVB (8525): fix a few assorted spelling mistakes.
  ...

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6
Linus Torvalds [Mon, 28 Jul 2008 15:33:25 +0000]
Merge git://git./linux/kernel/git/davem/sparc-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc: Set CONFIG_HAVE_ARCH_TRACEHOOK
  sparc: Add task_pt_regs().
  sparc: Add call to tracehook_signal_handler().
  sparc: Create and use TIF_NOTIFY_RESUME.
  sparc: Use tracehook routines in syscall_trace().
  sparc64: tracehook: CONFIG_HAVE_ARCH_TRACEHOOK
  sparc: Add user_stack_pointer().
  sparc64: tracehook_signal_handler
  sparc64: tracehook: TIF_NOTIFY_RESUME
  sparc: Add asm/syscall.h
  sparc64: tracehook syscall
  sparc: enable headers_export again
  sparc, sparc64: use arch/sparc/include

11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Mon, 28 Jul 2008 15:32:25 +0000]
Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: missing bits of net-namespace / sysctl
  ipcomp: Fix warnings after ipcomp consolidation.
  dccp: Add check for truncated ICMPv6 DCCP error packets
  dccp: Fix incorrect length check for ICMPv4 packets
  dccp: Add check for sequence number in ICMPv6 message
  dccp: Fix sequence number check for ICMPv4 packets
  dccp: Bug-Fix - AWL was never updated
  dccp: Allow to distinguish original and retransmitted packets

11 years agoSubmittingPatches: add git pull & diffstat format info
Randy Dunlap [Mon, 28 Jul 2008 03:44:24 +0000]
SubmittingPatches: add git pull & diffstat format info

Add git pull command info and diffstat summary info so that we don't
have to search email archives for it repeatedly.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agomore sysdev API change fallout - drivers/base/memory.c
Stephen Rothwell [Mon, 28 Jul 2008 01:05:04 +0000]
more sysdev API change fallout - drivers/base/memory.c

Noticed because of this warning:

  drivers/base/memory.c:279: warning: initialization from incompatible pointer type

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoACPI/CPUIDLE: prevent setting pm_idle to NULL
Thomas Gleixner [Sun, 27 Jul 2008 21:47:12 +0000]
ACPI/CPUIDLE: prevent setting pm_idle to NULL

pm_idle_save resp. pm_idle_old can be NULL when the restore code in
acpi_processor_cst_has_changed() resp. cpuidle_uninstall_idle_handler()
is called. This can set pm_idle unconditinally to NULL, which causes the
kernel to panic when calling pm_idle in the x86 idle code. This was
covered by an extra check for !pm_idle in the x86 idle code, which was
removed during the x86 idle code refactoring.

Instead of restoring the pm_idle check in the x86 code prevent the
acpi/cpuidle code to set pm_idle to NULL.

Reported by: Dhaval Giani http://lkml.org/lkml/2008/7/2/309
Based on a debug patch from Ingo Molnar

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoMerge branch 'i2c-for-linus' of git://aeryn.fluff.org.uk/bjdooks/linux
Linus Torvalds [Mon, 28 Jul 2008 15:28:50 +0000]
Merge branch 'i2c-for-linus' of git://aeryn.fluff.org.uk/bjdooks/linux

* 'i2c-for-linus' of git://aeryn.fluff.org.uk/bjdooks/linux:
  i2c: Blackfin I2C Driver: Functional power management support
  i2c: Documentation: upgrading clients HOWTO
  i2c: S3C24XX I2C frequency scaling support.
  i2c: i2c_gpio: keep probe resident for hotplugged devices.
  i2c: S3C2410: Pass the I2C bus number via drivers platform data

11 years agoipwireless: Preallocate received packet buffers with MRU size
David Sterba [Mon, 28 Jul 2008 14:53:32 +0000]
ipwireless: Preallocate received packet buffers with MRU size

ipwireless: Preallocate received packet buffers with MRU size

Packets are assembled from link size (~300 bytes) up to PPP MRU
(1500 by default). Try to preallocate full size rather than
repeatedly advance buffer size by 256 bytes.

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoipwireless: Put packets to pool start
David Sterba [Mon, 28 Jul 2008 14:53:27 +0000]
ipwireless: Put packets to pool start

ipwireless: Put packets to pool start

Put packets to pool start, try to reuse cached memory.

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoipwireless: Increase PPP outgoing queue size
David Sterba [Mon, 28 Jul 2008 14:53:21 +0000]
ipwireless: Increase PPP outgoing queue size

ipwireless: Increase PPP outgoing queue size

Increase default size of PPP outgoing queue. Currently set to 1, which
means that a packet quickly following another pushed by PPP must wait
until hardware actually sends the previous and PPP has to be waken up
by ppp_wakeup(). This slows down upstream.

Now PPP can push more packets at once which get buffered inside driver
and pushed immediatelly to hardware when previous packet is out.

Experiments show that size = 10 is quite good for all connection types
(GPRS/EDGE/UMTS) and gains 4 KB/sec of upload for UMTS for batch uploads.
Need for higher queue size than 10 occures in only < 0.1 % of cases.

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoipwireless: Explicitly request io and mem regions
David Sterba [Mon, 28 Jul 2008 14:53:16 +0000]
ipwireless: Explicitly request io and mem regions

ipwireless: Explicitly request io and mem regions

Documentation/pcmcia/driver-changes.txt says, that driver should call request_region
for used memory/io regions since PCMCIA does not do this (since 2.6.8).

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoipwireless: Constify buffer variables
David Sterba [Mon, 28 Jul 2008 14:53:11 +0000]
ipwireless: Constify buffer variables

ipwireless: Constify buffer variables

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoipwireless: Do not return value from sending funcs
David Sterba [Mon, 28 Jul 2008 14:53:05 +0000]
ipwireless: Do not return value from sending funcs

ipwireless: Do not return value from sending funcs

Do not return value from do_send_fragment and do_send_packet, it's not used.
The packet size checks are not useful too:

* zero length packet will never be sent, caller always passes packet_header
  size which is either 1 or 3
* MTU check is done in caller, no need to repeat

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoipwireless: Remove endian-dependent bitfields
David Sterba [Mon, 28 Jul 2008 14:53:00 +0000]
ipwireless: Remove endian-dependent bitfields

ipwireless: Remove endian-dependent bitfields

Remove endian-dependent bitfields and use bitmasks to transform
packet header bitfields from/to machine order.

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoipwireless: Glue splitted printk strings back
David Sterba [Mon, 28 Jul 2008 14:52:55 +0000]
ipwireless: Glue splitted printk strings back

ipwireless: Glue splitted printk strings back

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoipwireless: Remove pt_regs from interrupt handler
David Sterba [Mon, 28 Jul 2008 14:52:49 +0000]
ipwireless: Remove pt_regs from interrupt handler

ipwireless: Remove pt_regs from interrupt handler

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoipwireless: Rename spinlock variables to lock
David Sterba [Mon, 28 Jul 2008 14:52:44 +0000]
ipwireless: Rename spinlock variables to lock

ipwireless: Rename spinlock variables to lock

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoipwireless: Remove unused defines
David Sterba [Mon, 28 Jul 2008 14:52:39 +0000]
ipwireless: Remove unused defines

ipwireless: Remove unused defines

Remove unused defines, defines hiding variables, defines hiding 0.

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoipwireless: Misc cleanups
David Sterba [Mon, 28 Jul 2008 14:52:33 +0000]
ipwireless: Misc cleanups

ipwireless: Misc cleanups

- remove likely() and some extra () in ifs
- use unsigned in for loops
- remove useless typecasts
- remove obvious comments
- add () around ?:

Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

11 years agoi2c: Blackfin I2C Driver: Functional power management support
Michael Hennerich [Sun, 27 Jul 2008 06:41:54 +0000]
i2c: Blackfin I2C Driver: Functional power management support

PM_SUSPEND_MEM: Blackfin does not maintain register state through
Hibernate. Save and restore peripheral base initialization during
PM transitions.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

11 years agoi2c: Documentation: upgrading clients HOWTO
Ben Dooks [Mon, 28 Jul 2008 11:04:08 +0000]
i2c: Documentation: upgrading clients HOWTO

Add a document describing how i2c clients on Linux 2.6 can be
moved from the old to the new driver model.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>

11 years agoi2c: S3C24XX I2C frequency scaling support.
Ben Dooks [Mon, 28 Jul 2008 11:04:07 +0000]
i2c: S3C24XX I2C frequency scaling support.

Add support for CPU frequency scaling to the S3C24XX I2C driver.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>

11 years agoi2c: i2c_gpio: keep probe resident for hotplugged devices.
Ben Dooks [Mon, 28 Jul 2008 11:04:09 +0000]
i2c: i2c_gpio: keep probe resident for hotplugged devices.

Change the i2c_gpio driver to use platform_driver_register()
instead of platform_driver_probe() to ensure that is can
attach to any devices that may be loaded after it has initialised.

Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

11 years agoi2c: S3C2410: Pass the I2C bus number via drivers platform data
Ben Dooks [Mon, 28 Jul 2008 11:04:06 +0000]
i2c: S3C2410: Pass the I2C bus number via drivers platform data

Allow the platform data to specify the bus bumber that the
new I2C bus will be given. This is to allow the use of the
board registration mechanism to specify the new style of
I2C device registration which allows boards to provide a
list of attached devices.

Note, as discussed on the mailing list, we have dropped
backwards compatibility of adding an dynamic bus number
as it should not affect most boards to have the bus pinned
to 0 if they have either not specified platform data for
driver. Any board supplying platform data will automatically
have the bus_num field set to 0, and anyone who needs the
driver on a different bus number can supply platform data
to set bus_num.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>

11 years agoRemove deprecated virt_to_bus()
Karsten Keil [Mon, 28 Jul 2008 10:21:25 +0000]
Remove deprecated virt_to_bus()

Please pull from git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/ISDN-2.6.git master

This was a forgotten item in a printk from the old driver,
the DMA allocation use already the new interface.

Signed-off-by: Karsten Keil <kkeil@suse.de>

11 years agosh: SuperH Mobile CEU and camera platform data for AP325RXA
Magnus Damm [Mon, 28 Jul 2008 10:14:35 +0000]
sh: SuperH Mobile CEU and camera platform data for AP325RXA

Add AP325RXA specific platform data for on-chip sh7723 CEU and ncm03j camera.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Update smc911x platform data for AP325RXA
Magnus Damm [Mon, 28 Jul 2008 10:11:07 +0000]
sh: Update smc911x platform data for AP325RXA

Pass board specific smc911x parameters using struct smc911x_platdata.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: SuperH Mobile LCDC platform data for AP325RXA
Magnus Damm [Mon, 28 Jul 2008 10:07:04 +0000]
sh: SuperH Mobile LCDC platform data for AP325RXA

Add LCD panel platform data for the AP325RXA board.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Add SuperH Mobile CEU platform data for Migo-R
Magnus Damm [Mon, 28 Jul 2008 09:51:01 +0000]
sh: Add SuperH Mobile CEU platform data for Migo-R

Add Migo-R specific platform data for on-chip sh7722 CEU and ov772x camera.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Add SuperH Mobile LCDC platform data for Migo-R
Magnus Damm [Mon, 28 Jul 2008 09:47:30 +0000]
sh: Add SuperH Mobile LCDC platform data for Migo-R

Add WVGA and QVGA LCD panel support to Migo-R.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Move asid_cache() out of ifdef to fix SH-3/4 nommu build.
Paul Mundt [Mon, 28 Jul 2008 09:39:25 +0000]
sh: Move asid_cache() out of ifdef to fix SH-3/4 nommu build.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Workaround for __put_user_asm() bug with gcc 4.x on big-endian.
Yoshinori Sato [Mon, 28 Jul 2008 09:36:13 +0000]
sh: Workaround for __put_user_asm() bug with gcc 4.x on big-endian.

I think this problem is GCC(4.1.2) bug.
Syscall "getdents" returned "dirent->d_off" is always 0.
I think other EB enviroment have same problem.

Problem code
0c03c954 <filldir>:
 :
 c03c97a:       58 f7           mov.l   @(28,r15),r8 !-> offset (high)
 c03c97c:       59 f8           mov.l   @(32,r15),r9 !-> offset (low)
 c03c97e:       53 f9           mov.l   @(36,r15),r3
 c03c980:       54 fa           mov.l   @(40,r15),r4
 :
 c03c9a0:       21 82           mov.l   r8,@r1 !offset(high) -> dirent->d_off

It's workaround patch.

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Wire up new syscalls.
Paul Mundt [Mon, 28 Jul 2008 09:34:45 +0000]
sh: Wire up new syscalls.

This wires up the signalfd4, eventfd2, epoll_create1, dup3, pipe2, and
inotify_init1 syscalls.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: fix uImage Entry Point
Yoshihiro Shimoda [Wed, 23 Jul 2008 07:49:06 +0000]
sh: fix uImage Entry Point

fix the problem that cannot boot using uImage when PAGE_SIZE is
8kbyte or 64kbyte.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh_keysc: remove request_mem_region() and release_mem_region()
Tetsuya Mukawa [Fri, 18 Jul 2008 22:46:53 +0000]
sh_keysc: remove request_mem_region() and release_mem_region()

Remove request_mem_region() and release_mem_region() from sh_keysc driver.
Those functions can find resource conflict, but it is already checked in
platform_device_add().

Signed-off-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Don't miss pending signals returning to user mode after signal processing
Stuart MENEFY [Thu, 17 Jul 2008 12:08:40 +0000]
sh: Don't miss pending signals returning to user mode after signal processing

Without this patch, signals sent during architecture specific signal
handling (typically as a result of the user's stack being inaccessible)
are ignored.

This is the SH version of commit c3ff8ec31c1249d268cd11390649768a12bec1b9
which was for the i386.

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Use clk_always_enable() on sh7366
Magnus Damm [Thu, 17 Jul 2008 10:20:11 +0000]
sh: Use clk_always_enable() on sh7366

Use clk_always_enable() in the sh7366 processor code.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Use clk_always_enable() on sh7343 / SE77343
Magnus Damm [Thu, 17 Jul 2008 10:18:24 +0000]
sh: Use clk_always_enable() on sh7343 / SE77343

Use clk_always_enable() on the sh7343 processor and in the board code
for Solution Engine 7343. Remove duplicate MSTPCR register definitions.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Use clk_always_enable() on sh7722 / Migo-R / SE7722
Magnus Damm [Thu, 17 Jul 2008 10:16:11 +0000]
sh: Use clk_always_enable() on sh7722 / Migo-R / SE7722

Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Use clk_always_enable() on sh7723 / ap325rxa
Magnus Damm [Thu, 17 Jul 2008 10:13:34 +0000]
sh: Use clk_always_enable() on sh7723 / ap325rxa

Use clk_always_enable() on the sh7723 processor and in the ap325rxa
board code. Remove duplicate MSTPCR register definitions.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Introduce clk_always_enable() function
Magnus Damm [Thu, 17 Jul 2008 10:09:51 +0000]
sh: Introduce clk_always_enable() function

Add SuperH specific funcion clk_always_enable(), useful to enable MSTPCR
bits in processor or board specific code.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Show all clocks and their state in /proc/clocks
Magnus Damm [Thu, 17 Jul 2008 10:05:54 +0000]
sh: Show all clocks and their state in /proc/clocks

Show all clocks in /proc/clocks, and also show if they are enabled or
disabled. This is useful to show MSTPCR bits on SuperH Mobile processors.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Merge sh7343 and sh7722 clock code
Magnus Damm [Thu, 17 Jul 2008 10:02:23 +0000]
sh: Merge sh7343 and sh7722 clock code

This code makes sh7343 share the sh7722 clock code. Instead of just using
the good and very old sh7343 clock implmentation, switch to the new MSTPCR
enabled clock code. SIU clocks are disabled on sh7343 for now.

With this change all SuperH Mobile devices now use the same clock code.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Add SuperH Mobile MSTPCR bits to clock framework
Magnus Damm [Thu, 17 Jul 2008 09:56:15 +0000]
sh: Add SuperH Mobile MSTPCR bits to clock framework

Handle module stop clock bits in MSTPCRn through the clock framework.
The clocks are named after the bits in the data sheet. The association
between bit number and hardware block is processor specific.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Use arch_flags to simplify sh7722 siu clock code
Magnus Damm [Thu, 17 Jul 2008 09:52:19 +0000]
sh: Use arch_flags to simplify sh7722 siu clock code

Make use of arch_flags to simplify the SIU clock code.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Add arch_flags to struct clk
Magnus Damm [Thu, 17 Jul 2008 09:48:57 +0000]
sh: Add arch_flags to struct clk

Add arch_flags to struct clk so we can keep per-clock private data
somewhere and share code between multiple clocks.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agofix sh ptep_get_and_clear breakage
Adrian Bunk [Wed, 16 Jul 2008 16:45:40 +0000]
fix sh ptep_get_and_clear breakage

Commit 1ea0704e0da65b2b46f9142ff1391163aac24060
(mm: add a ptep_modify_prot transaction abstraction)
triggered on sh build errors like the following:

<--  snip  -->

...
CC arch/sh/mm/pg-sh4.o
cc1: warnings being treated as errors
include2/asm/pgtable.h:139: error: 'ptep_get_and_clear' declared inline after being called
include2/asm/pgtable.h:139: error: previous declaration of 'ptep_get_and_clear' was here
make[2]: *** [arch/sh/mm/pg-sh4.o] Error 1

<--  snip  -->

Since there's no good reason for marking these global functions as
"inline" this patch therefore removes the inline's.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Renesas R0P7785LC0011RL board support
Yoshihiro Shimoda [Wed, 16 Jul 2008 11:21:09 +0000]
sh: Renesas R0P7785LC0011RL board support

This adds initial support for the Renesas R0P7785LC0011RL board.
This patch supports 29bit address mode only.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Add memory chunks to SH-Mobile UIO devices
Magnus Damm [Wed, 16 Jul 2008 10:02:54 +0000]
sh: Add memory chunks to SH-Mobile UIO devices

This patch adds physically contiguous memory chunks to the UIO devices.
The same strategy can be used in the future for the CEU as well.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Export sh7366 VPU, VEU(1), VEU(2) using uio_pdrv_genirq
Magnus Damm [Tue, 15 Jul 2008 12:55:03 +0000]
sh: Export sh7366 VPU, VEU(1), VEU(2) using uio_pdrv_genirq

This patch exports the VPU, VEU(1) and VEU(2) blocks of the sh7366
to user space using the uio_pdrv_genirq platform driver.

While at it, fix up the VEU(2) interrupt vector.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Export sh7723 VPU, VEU2H0, VEU2H1 using uio_pdrv_genirq
Magnus Damm [Tue, 15 Jul 2008 12:53:33 +0000]
sh: Export sh7723 VPU, VEU2H0, VEU2H1 using uio_pdrv_genirq

This patch exports the VPU, VEU2H0 and VEU2H1 blocks of the sh7723
to user space using the uio_pdrv_genirq platform driver.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Export sh7722 VPU and VEU using uio_pdrv_genirq
Magnus Damm [Tue, 15 Jul 2008 12:52:19 +0000]
sh: Export sh7722 VPU and VEU using uio_pdrv_genirq

This patch exports the VPU and VEU blocks of the sh7722 to user space
using the uio_pdrv_genirq platform driver.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Export sh7343 VPU and VEU using uio_pdrv_genirq
Magnus Damm [Tue, 15 Jul 2008 12:51:39 +0000]
sh: Export sh7343 VPU and VEU using uio_pdrv_genirq

This patch exports the VPU and VEU blocks of the sh7343 to user space
using the uio_pdrv_genirq platform driver.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh2(A) exception handler update
Yoshinori Sato [Wed, 9 Jul 2008 16:20:03 +0000]
sh2(A) exception handler update

This patch is

By sh2
- Remove duplicate code
- Reduce stack usage
- Cleanup and little optimize

By sh2a
- Add missing handler(256 to 511)
- Use sh2a instructions handler

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: update Solution Engine 7343
Yoshihiro Shimoda [Mon, 7 Jul 2008 12:11:54 +0000]
sh: update Solution Engine 7343

updated the following codes for Solution Endine 7343:
 - fix compile error in arch/sh/boards/se/7343/irq.c
 - add nor flash physmaps
 - update defconfig

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: update sh7343 code
Yoshihiro Shimoda [Mon, 7 Jul 2008 12:11:51 +0000]
sh: update sh7343 code

updated the following codes for SH7343:
 - add register_intc_controller()
 - add EARLY_SCIF_CONSOLE_PORT
 - add define of CPG register

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: fix pg-sh4.c build breakage in linux-next
Magnus Damm [Sat, 5 Jul 2008 03:33:30 +0000]
sh: fix pg-sh4.c build breakage in linux-next

Remove inline from ptep_get_and_clean() to match with header file prototype.
Makes linux-next build.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: enable I2C on the ap325rxa board
Magnus Damm [Sat, 5 Jul 2008 03:32:44 +0000]
sh: enable I2C on the ap325rxa board

This patch enables I2C on the sh7723-based ap325rxa board.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: add SuperH Mobile I2C platform data to sh7366
Magnus Damm [Sat, 5 Jul 2008 03:32:23 +0000]
sh: add SuperH Mobile I2C platform data to sh7366

This patch adds platform data for the single I2C channel on sh7366.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: add SuperH Mobile I2C platform data to sh7723
Magnus Damm [Sat, 5 Jul 2008 03:32:06 +0000]
sh: add SuperH Mobile I2C platform data to sh7723

This patch adds platform data for the single I2C channel on sh7723.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: add SuperH Mobile I2C platform data to sh7343
Magnus Damm [Sat, 5 Jul 2008 03:31:46 +0000]
sh: add SuperH Mobile I2C platform data to sh7343

This patch adds platform data for two I2C channels to the sh7343.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: add interrupt ack code to sh4a
Yoshihiro Shimoda [Fri, 4 Jul 2008 03:37:12 +0000]
sh: add interrupt ack code to sh4a

This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Fix up link error on SH-2 zImage with older binutils.
Yoshinori Sato [Fri, 4 Jul 2008 03:54:51 +0000]
sh: Fix up link error on SH-2 zImage with older binutils.

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Conditionally re-enable IRQs in fault path.
Stuart Menefy [Wed, 2 Jul 2008 08:51:23 +0000]
sh: Conditionally re-enable IRQs in fault path.

The current kernel behaviour is to reenable interrupts unconditionally
when taking a page fault. This patch changes this to only enable them
if interrupts were previously enabled.

It also fixes a problem seen with this fix in place: the kernel previously
flushed the vsyscall page when handling a signal, which is not only
unncessary, but caused a possible sleep with interrupts disabled.

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Record the major cut revision for probed SH-4A parts.
Paul Mundt [Wed, 2 Jul 2008 08:46:40 +0000]
sh: Record the major cut revision for probed SH-4A parts.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Optimized flush_icache_range() implementation.
Chris Smith [Wed, 2 Jul 2008 06:17:11 +0000]
sh: Optimized flush_icache_range() implementation.

Add implementation of flush_icache_range() suitable for signal handler
and kprobes. Remove flush_cache_sigtramp() and change signal.c to use
flush_icache_range().

Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Stub in silicon cut in CPU info.
Stuart Menefy [Wed, 2 Jul 2008 06:15:09 +0000]
sh: Stub in silicon cut in CPU info.

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Tidy up the SH-3 exception vector table.
Paul Mundt [Wed, 2 Jul 2008 04:58:38 +0000]
sh: Tidy up the SH-3 exception vector table.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agoSH7619 add ethernet controler support
Yoshinori Sato [Wed, 2 Jul 2008 02:20:24 +0000]
SH7619 add ethernet controler support

- Add EtherC + PHY resource define.

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Remove sh_pcic_io_xxx function from Solution Engine IO code
Nobuhiro Iwamatsu [Tue, 24 Jun 2008 04:00:52 +0000]
sh: Remove sh_pcic_io_xxx function from Solution Engine IO code

sh_pcic_io_xxx function are very old.
In linux-2.4, mrshpc_ss socket driver used this function.
But there is not this driver to the present kernel.
I deleted these cords and checked operation.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Fix Kconfig of AP-325RXA
Nobuhiro Iwamatsu [Thu, 19 Jun 2008 10:27:55 +0000]
sh: Fix Kconfig of AP-325RXA

The CPU of AP-325RXA is SH7723, but a CPU becomes selectable.
This patch fixes this problem.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Clean up code of Solution Engine 770x
Nobuhiro Iwamatsu [Wed, 18 Jun 2008 09:32:03 +0000]
sh: Clean up code of Solution Engine 770x

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Update Solution Enginge 7712 defconfig
Nobuhiro Iwamatsu [Wed, 18 Jun 2008 09:31:46 +0000]
sh: Update Solution Enginge 7712 defconfig

Enable SH-Ether support and NFS userland support.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Solution Enginge 7710/7712 SH-Ether support
Nobuhiro Iwamatsu [Wed, 18 Jun 2008 09:29:06 +0000]
sh: Solution Enginge 7710/7712 SH-Ether support

Add support SH-Ether for Hitachi Solution Engine.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh/kernel/ cleanups
Adrian Bunk [Wed, 18 Jun 2008 00:36:50 +0000]
sh/kernel/ cleanups

This patch contains the following cleanups:
- make the following needlessly global code static:
  - cf-enabler.c: cf_init()
  - cpu/clock.c: __clk_enable()
  - cpu/clock.c: __clk_disable()
  - process_32.c: default_idle()
  - time_32.c: struct clocksource_sh
  - timers/timer-tmu.c: struct tmu_timer_ops
- remove the following unused functions (no CONFIG_BLK_DEV_FD on sh):
  - process_{32,64}.c: disable_hlt()
  - process_{32,64}.c: enable_hlt()

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: make pcibios_max_latency static
Adrian Bunk [Tue, 17 Jun 2008 22:33:40 +0000]
sh: make pcibios_max_latency static

This patch makes the needlessly global pcibios_max_latency static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: make EARLY_PCI_OP's static
Adrian Bunk [Tue, 17 Jun 2008 22:31:03 +0000]
sh: make EARLY_PCI_OP's static

This patch makes the needlessly global EARLY_PCI_OP's static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh/boards/dreamcast/rtc.c: make 2 functions static
Adrian Bunk [Tue, 17 Jun 2008 22:30:57 +0000]
sh/boards/dreamcast/rtc.c: make 2 functions static

This patch makes the needlessly global aica_rtc_{get,set}timeofday()
static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agomaple: tidy maple_driver code by removing redundant connect/disconnect
Adrian McMenamin [Sun, 15 Jun 2008 19:48:09 +0000]
maple: tidy maple_driver code by removing redundant connect/disconnect

The connect and disconnect functions are unnecessary - everything they do can be
accomplished in the initial probe - so remove them.

Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Renesas Solutions SH7763RDP board support
Nobuhiro Iwamatsu [Fri, 6 Jun 2008 08:04:56 +0000]
sh: Renesas Solutions SH7763RDP board support

This patch adds basic support for the SH7763RDP board.
This supports a basic stuff provided in SH7763, like SCIF,
NOR Flash and USB host.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Add SCIF2 support for SH7763.
Nobuhiro Iwamatsu [Fri, 6 Jun 2008 08:04:08 +0000]
sh: Add SCIF2 support for SH7763.

SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

11 years agosh: Add support Renesas Solutions AP-325RXA board
Yusuke Goda [Fri, 6 Jun 2008 08:03:23 +0000]
sh: Add support Renesas Solutions AP-325RXA board

This board is SH7723 base board.

This has SCIF, LCDC, USB Host controler, NOR/NAND Flash, Sound,
Ether and other.

This patch supports SCIF, NOR Flash.

Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>