10 years ago[SCSI] fcoe, libfc: adds exchange manager(EM) anchor list per lport and related APIs
Vasu Dev [Thu, 30 Jul 2009 00:05:00 +0000]
[SCSI] fcoe, libfc: adds exchange manager(EM) anchor list per lport and related APIs

Adds EM list using a anchor struct fc_exch_mgr_anchor, anchor is used
to allow same EM instance sharing across more than one lport on a eth
device, this implementation is per discussed design posted at
http://www.open-fcoe.org/pipermail/devel/2009-June/002566.html.

The shared EM is required for multiple lports on eth device when
using multiple VLANs or NPIV.

Adds fc_exch_mgr_add API to add a EM to the lport and fc_exch_mgr_del
API to delete previously added EM.

Also adds function fc_exch_mgr_destroy() to destroy allocated EM.
The kref is added to the EM to keep track of EM usage count, the EM is
destroyed when no longer in use upon kref reaching to zero.

The caller can specify match function to fc_exch_mgr_add, this
will be used in determining exchange allocation from its EM or not.

Moved calling of fcoe_em_config below fcoe_libfc_config calling,
so that list head lp->ema_list is initialized before configuring
EM.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] libfc: fix: cancel rport retry timer
Joe Eykholt [Thu, 30 Jul 2009 00:04:54 +0000]
[SCSI] libfc: fix: cancel rport retry timer

The timer for rport retries wasn't getting canceled, and
would occasionally go off after the module was unloaded.

Add logic to cancel the timer in fc_rport_work().

Since we cancel the timer before deleting the rdata,
it is no longer necessary to do a get_device() for the pending timer.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] libfc: fc_rport_logoff should not drop the lock
Joe Eykholt [Thu, 30 Jul 2009 00:04:49 +0000]
[SCSI] libfc: fc_rport_logoff should not drop the lock

fc_rport_logoff drops the rport lock in order to cancel work
that may be pending.  This is undesirable as the state can
completely change, and the caller may not expect that the
lock could've been dropped.

If there is work pending, it will acquire the rdata mutex and
so we're protected and can change the event from READY to DELETE.
Queue the work only if there is no event already pending.

There were a couple other cases where the state was set to
DELETE and work queued, even though the state may have already
been DELETE.  Fix these using a common function fc_rport_enter_delete().

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] libfc: rename rport state "NONE" to "DELETE".
Joe Eykholt [Thu, 30 Jul 2009 00:04:43 +0000]
[SCSI] libfc: rename rport state "NONE" to "DELETE".

State RPORT_ST_NONE was intented to be an invalid state (0), never used.
This was a misguided attempt to be sure it was always initialized.
Having an extra state meaning nothing requires switch statements to
have a case covering that state.

State NONE has been used instead to mean the remote port is being deleted.
Changing the name to RPORT_ST_DELETE.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] libfc: fix WARNING from fc_seq_start_next on closed exchanges
Joe Eykholt [Thu, 30 Jul 2009 00:04:38 +0000]
[SCSI] libfc: fix WARNING from fc_seq_start_next on closed exchanges

We saw periodic messages like:

WARNING: at drivers/scsi/libfc/fc_exch.c:825 fc_seq_start_next+0x30/0x4b

This was due to trying to allocate a sequence in a request handler
when the exchange had been reset.

Delete the WARN_ON.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] libfc: in fc_lport_destroy, flush rports after turning off link
Joe Eykholt [Thu, 30 Jul 2009 00:04:33 +0000]
[SCSI] libfc: in fc_lport_destroy, flush rports after turning off link

During an fcoe module unload, we saw a problem where fc_rport_work()
finds the lport has been freed.  The rdata points to an area
containing 0x6b6b6b6b... the pool poison value from kmem_free().

In fcoe_if_destroy() we call fc_fabric_logoff() then fc_lport_destroy().
fc_fabric_logoff() flushes the remote port work, but we're still receiving
requests, and an RSCN or PLOGI arrives which creates more rports.

Note that although the LLD also checks link_up, it doesn't do it
under the lport mutex, so it can deliver frames to
fc_lport_recv_req() even after link_up is cleared.
So, re-check link_up there.

We need to flush the rports by calling disc_stop_final()
after we clear link_up.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] libfc: stop login after fabric logoff
Joe Eykholt [Thu, 30 Jul 2009 00:04:27 +0000]
[SCSI] libfc: stop login after fabric logoff

When removing the fcoe module, several lports were being shut down
through fc_lport_fabric_logoff().

Occasionally, one would enter reset state before fc_lport_destroy()
was called, and since link_up was still true, it would log back in.

If we just clear link_up earlier, then we wouldn't be accepting LOGO
requests from other initiators while we are shutting down.

Fix by changing the LOGO response handler to enter DISABLED instead
of RESET.  Add an fc_lport_enter_disabled() function which does
what fc_lport_enter_reset() did, except it doesn't proceed to FLOGI state.

Move the code that was common between fc_lport_enter_reset() and
fc_lport_enter_disabled() into a new fc_lport_reset_locked() function.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] libfc: rename lport NONE state to DISABLED
Joe Eykholt [Thu, 30 Jul 2009 00:04:22 +0000]
[SCSI] libfc: rename lport NONE state to DISABLED

The state NONE was meant to be invalid, but has been used as
the initial state.  Rename it to be DISABLED, as more descriptive.
Further patches will make it the like the RESET state, except
it won't transition to FLOGI until fc_lport_fabric_login() is called.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] fcoe: stop delivery of received frames before doing lport_destroy()
Joe Eykholt [Thu, 30 Jul 2009 00:04:17 +0000]
[SCSI] fcoe: stop delivery of received frames before doing lport_destroy()

To be more sure that no more input arrives at the local port as
it is being destroyed, clean the queues in the per-cpu receive
threads.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] libfc: change debug messages to give host number.
Joe Eykholt [Thu, 30 Jul 2009 00:04:12 +0000]
[SCSI] libfc: change debug messages to give host number.

libfc debug messages currently show 'lport: <fc-id>:'
wher <fc-id> is the hex assigned port-id.  When the lport
is logged off, that will be zero, so its hard to distinguish
which instance is involved.  The FC-ID can change
if the port is re-patched or changes VSANs.

Two lports may even have the same FC-ID if connected to isolated SANs.

Change the debug messages to print the SCSI host number "hostN:",
which will not change for the life of the lport.
Still show the FC_ID on lport messages.

Also, add a macro to FC_RPORT_ID_DBG for rport debugging where there's
no rdata structure involved.  It takes the lport and port_id as parameters.
Use this in fc_rport_recv_plogi_req() and fc_rport_recv_logo_req().

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] libfc: remove extra semicolons from debug macros
Joe Eykholt [Thu, 30 Jul 2009 00:04:06 +0000]
[SCSI] libfc: remove extra semicolons from debug macros

This is unlikely to cause any problems, but the libfc debug macros
introduce extra undesirable semicolons.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] fcoe: Call dev_ethtool_get_settings() in fcoe_link_ok
Yi Zou [Thu, 30 Jul 2009 00:04:01 +0000]
[SCSI] fcoe: Call dev_ethtool_get_settings() in fcoe_link_ok

No need to check phys_dev here, just call dev_ethtool_get_settings() directly
will take care of this.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] libfcoe: Set fip_flags according to fcf and lport's capability of SPMA support
Yi Zou [Thu, 30 Jul 2009 00:03:55 +0000]
[SCSI] libfcoe: Set fip_flags according to fcf and lport's capability of SPMA support

When encap the els for FIP, set the fip_flags according to the FCF and lport's
capability of supporting SPMA or FPMA or both.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] fcoe: Fix validation of mac address when checking for spma support
Yi Zou [Thu, 30 Jul 2009 00:03:50 +0000]
[SCSI] fcoe: Fix validation of mac address when checking for spma support

Fix this bug of validating the wrong mac address while checking for SAN MAC
address support from LLD as we should check ha->addr not ctlr.ctl_src_addr.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] ALUA: send STPG if explicit and implicit is supported
Mike Christie [Wed, 29 Jul 2009 04:08:06 +0000]
[SCSI] ALUA: send STPG if explicit and implicit is supported

alua_activate only sends a STPG if only explicit is suppored.
As a result, for EMC targets that support both we end up doing
a implicit failover when X commands are finally sent to
the other SP.

This patch does a AND on the h->tpgs, so we do a explicit failover
right away.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] scsi_transport_sas: fix incorrect duplicate setup of max_phys
James Bottomley [Tue, 28 Jul 2009 16:39:05 +0000]
[SCSI] scsi_transport_sas: fix incorrect duplicate setup of max_phys

There are two setup places for max_phys in scsi_transport_sas.c; one
incorrectly places a NULL into host_attrs instead of port_attrs.  Remove it.

Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] fc_transport: Correct max fc_host attribute count
James Smart [Tue, 28 Jul 2009 16:30:01 +0000]
[SCSI] fc_transport: Correct max fc_host attribute count

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] lpfc 8.3.4: Update driver version to 8.3.4
James Smart [Sun, 19 Jul 2009 14:01:44 +0000]
[SCSI] lpfc 8.3.4: Update driver version to 8.3.4

Update driver version to 8.3.4

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] lpfc 8.3.4: Remove spaces before newlines in several log messages
James Smart [Sun, 19 Jul 2009 14:01:38 +0000]
[SCSI] lpfc 8.3.4: Remove spaces before newlines in several log messages

Remove spaces before newlines in several log messages

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] lpfc 8.3.4: Add bsg (SGIOv4) support for ELS/CT support
James Smart [Sun, 19 Jul 2009 14:01:32 +0000]
[SCSI] lpfc 8.3.4: Add bsg (SGIOv4) support for ELS/CT support

Add bsg (SGIOv4) support for sending and receiving ELS, CT commands

This patch adds a new file, lpfc_bsg.c.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] lpfc 8.3.4: NPIV vport fixes
James Smart [Sun, 19 Jul 2009 14:01:26 +0000]
[SCSI] lpfc 8.3.4: NPIV vport fixes

NPIV vport fixes

- Fixed static vport creation on SLI4 HBAs
- Fixed vport create sending init_vpi before REG_VFI
- Fix unable to create vports on SLI4 HBA's Port2

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] lpfc 8.3.4: Fix a pair of FCoE issues
James Smart [Sun, 19 Jul 2009 14:01:21 +0000]
[SCSI] lpfc 8.3.4: Fix a pair of FCoE issues

Fix a pair of FCoE issues

- Fix Region 23 FCoE Parameters not being read correctly
- Fix race condition when there are FCoE events during FCF table read

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] lpfc 8.3.4: Various SLI3 fixes
James Smart [Sun, 19 Jul 2009 14:01:16 +0000]
[SCSI] lpfc 8.3.4: Various SLI3 fixes

Various SLI3 fixes

- Fix for firmware dump failure
- Fix inband remote management

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] lpfc 8.3.4: Consistently Implement persistent port disable
James Smart [Sun, 19 Jul 2009 14:01:10 +0000]
[SCSI] lpfc 8.3.4: Consistently Implement persistent port disable

Consistently implement persistent port disable.

Ability was to be managed in the adapter via firmware via flash settings.
However, not all firmware images supported it. Uniformly support it
everywhere.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] lpfc 8.3.4: Various SLI4 fixes
James Smart [Sun, 19 Jul 2009 14:01:03 +0000]
[SCSI] lpfc 8.3.4: Various SLI4 fixes

Various SLI4 fixes

- Fix switch name not used in the FCF record for FCoE HBAs
- Enabled HBA UE error polling error-condition action code
- Rewrite lpfc_sli4_scmd_to_wqidx_distr() to handle counter rollover cleanly
- Modify resume_rpi mailbox data structure to match current SLI4 spec
- Do not issue mailbox command in MBX_POLL mode when LPFC_HBA_ERROR is set
- Wait for HBA POST completion before checking Online and UE registers
- Fix accumulated total length not being filled in on unsolicited IOCBs
- Use PCI config space register to determine SLI rev of HBA
- Turn on starting ELS tmo function timer during device initialization

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] fcoe: convert to %pM
Johannes Berg [Wed, 15 Jul 2009 15:21:14 +0000]
[SCSI] fcoe: convert to %pM

print_mac is being deprecated, and %pM makes for smaller
code anyway.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] lpfc: don't dereference NULL
Jiri Slaby [Mon, 13 Jul 2009 21:25:54 +0000]
[SCSI] lpfc: don't dereference NULL

When kzalloc fails in lpfc_hba_alloc, don't dereference the NULL by
lpfc_printf_log. Use dev_err instead.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-By: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] qla2xxx: Fix __LITTLE_ENDIAN definition warnings
Dave Jones [Mon, 13 Jul 2009 20:27:46 +0000]
[SCSI] qla2xxx: Fix __LITTLE_ENDIAN definition warnings

On ppc64, gcc 4.4 spews lots of..

drivers/scsi/qla2xxx/qla_def.h:1485:7: warning: "__LITTLE_ENDIAN" is not defined

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] bnx2i: register given device with cnic if shost != NULL in ep_connect()
Anil Veerabhadrappa [Thu, 9 Jul 2009 01:21:01 +0000]
[SCSI] bnx2i: register given device with cnic if shost != NULL in ep_connect()

When using iface, bnx2i was unable to offload further connections after all
active sessions are logged out. bnx2i will unregister the device from cnic
when the last connection is torn down. Next call to ep_connect() will fail
because the device is not registered. This issue is not seen if shost == NULL
is passed to ep_connect() call because in that case bnx2i will registers all
known devices with cnic before doing a route look-up.  When shost != NULL,
bnx2i knows the device on which to offload the connection and has to register
this device before attempting to offload the connection

Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] scsi_transport_fc: fix kernel-doc param name
Randy Dunlap [Sat, 4 Jul 2009 20:10:41 +0000]
[SCSI] scsi_transport_fc: fix kernel-doc param name

Change function parameter name in kernel-doc to match the function's
actual parameter name, to fix 2 kernel-doc warnings.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] bnx2i: convert bnx2i_dev_lock to mutex
Anil Veerabhadrappa [Tue, 23 Jun 2009 21:07:40 +0000]
[SCSI] bnx2i: convert bnx2i_dev_lock to mutex

convert bnx2i_dev_lock to type mutex from rwlock_t because
cnic->register_device() can sleep for various reasons including memory
allocation, waiting for ISCSI_INIT completion and while acquiring mutex lock,
cnic_lock.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] bnx2i: bug fixes in bnx2i_init_one to handle error conditions
Anil Veerabhadrappa [Tue, 23 Jun 2009 21:04:23 +0000]
[SCSI] bnx2i: bug fixes in bnx2i_init_one to handle error conditions

Fixed bnx2i_init_one() to properly handle return code of
cnic->register_device() and propagate it back to the caller.  No need to check
for BNX2I_CNIC_REGISTERED, because unless the adapter is added to adapter_list
it will not be registered in ep_connect context

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] bnx2i: remove global variable bnx2i_reg_devices
Anil Veerabhadrappa [Tue, 23 Jun 2009 20:56:29 +0000]
[SCSI] bnx2i: remove global variable bnx2i_reg_devices

Removed bnx2i_reg_devices as this counter is not really
used in a meaningful way

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] Print failed commands
Martin K. Petersen [Sat, 23 May 2009 15:45:07 +0000]
[SCSI] Print failed commands

When a request fails we print the sense data but not the actual command
that failed.  Add a printout of the operation + CDB for failed commands.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] scsi_dh: Reference count scsi_dh_attach
Chandra Seetharaman [Sat, 27 Jun 2009 02:30:06 +0000]
[SCSI] scsi_dh: Reference count scsi_dh_attach

Problem reported: http://marc.info/?l=dm-devel&m=124585978305866&w=2

scsi_dh does not do a refernce count for attach/detach, and this affects
the way it is supposed to work with multipath when a device is not
in the dev_list of the hardware handler.

This patch adds a reference count that counts each attach.

Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years ago[SCSI] update scsi/constants.c
Douglas Gilbert [Thu, 25 Jun 2009 19:43:02 +0000]
[SCSI] update scsi/constants.c

It has been 3 years since this file was sync-ed with
www.t10.org . Information taken from the last bunch
of drafts released in May 2009. More asc/ascq codes
are coming for thin provisioning; when approved and
allocated another patch could add them prior to this
patch going live.

Changelog:
   - add some new command names and rename two commands
   - sync asc/ascq table with www.t10.org/lists/asc-num.txt
   - correct bug in scsi_extd_sense_format() [second
     for loop]

Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

10 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes...
Linus Torvalds [Sat, 22 Aug 2009 19:14:01 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: check saved state before restore

10 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
Linus Torvalds [Sat, 22 Aug 2009 15:30:58 +0000]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] mpt2sas: fix config request and diag reset deadlock
  [SCSI] mpt2sas: Bump driver version 01.100.04.00
  [SCSI] mpt2sas: fix oops because drv data points to NULL on resume from hibernate
  [SCSI] mpt2sas: fix crash due to Watchdog is active while OS in standby mode
  [SCSI] mpt2sas: fix infinite loop inside config request
  [SCSI] mpt2sas: Excessive log info causes sas iounit page time out
  [SCSI] mpt2sas: Raid 10 Value is showing as Raid 1E in /va/log/messages
  [SCSI] mpt2sas: Expander fix oops saying "Already part of another port"
  [SCSI] mpt2sas: Introduced check for enclosure_handle to avoid crash

10 years agoLinux 2.6.31-rc7
Linus Torvalds [Sat, 22 Aug 2009 01:00:46 +0000]
Linux 2.6.31-rc7

10 years agoRe-introduce page mapping check in mark_buffer_dirty()
Linus Torvalds [Sat, 22 Aug 2009 00:40:08 +0000]
Re-introduce page mapping check in mark_buffer_dirty()

In commit a8e7d49aa7be728c4ae241a75a2a124cdcabc0c5 ("Fix race in
create_empty_buffers() vs __set_page_dirty_buffers()"), I removed a test
for a NULL page mapping unintentionally when some of the code inside
__set_page_dirty() was moved to the callers.

That removal generally didn't matter, since a filesystem would serialize
truncation (which clears the page mapping) against writing (which marks
the buffer dirty), so locking at a higher level (either per-page or an
inode at a time) should mean that the buffer page would be stable.  And
indeed, nothing bad seemed to happen.

Except it turns out that apparently reiserfs does something odd when
under load and writing out the journal, and we have a number of bugzilla
entries that look similar:

http://bugzilla.kernel.org/show_bug.cgi?id=13556
http://bugzilla.kernel.org/show_bug.cgi?id=13756
http://bugzilla.kernel.org/show_bug.cgi?id=13876

and it looks like reiserfs depended on that check (the common theme
seems to be "data=journal", and a journal writeback during a truncate).

I suspect reiserfs should have some additional locking, but in the
meantime this should get us back to the pre-2.6.29 behavior.

Pattern-pointed-out-by: Roland Kletzing <devzero@web.de>
Cc: stable@kernel.org (2.6.29 and 2.6.30)
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoMerge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied...
Linus Torvalds [Fri, 21 Aug 2009 17:45:09 +0000]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon: add GET_PARAM/INFO support for Z pipes
  drm/radeon/kms: add r100/r200 OQ support.
  drm: Fix sysfs device confusion.
  drm/radeon/kms: implement the bo busy ioctl properly.

10 years agoMerge branch 'btrfs' of git://git.kernel.dk/linux-2.6-block
Linus Torvalds [Fri, 21 Aug 2009 16:56:55 +0000]
Merge branch 'btrfs' of git://git.kernel.dk/linux-2.6-block

* 'btrfs' of git://git.kernel.dk/linux-2.6-block:
  btrfs: fix inode rbtree corruption

10 years agox86: don't call '->send_IPI_mask()' with an empty mask
Linus Torvalds [Fri, 21 Aug 2009 16:48:10 +0000]
x86: don't call '->send_IPI_mask()' with an empty mask

As noted in 83d349f35e1ae72268c5104dbf9ab2ae635425d4 ("x86: don't send
an IPI to the empty set of CPU's"), some APIC's will be very unhappy
with an empty destination mask.  That commit added a WARN_ON() for that
case, and avoided the resulting problem, but didn't fix the underlying
reason for why those empty mask cases happened.

This fixes that, by checking the result of 'cpumask_andnot()' of the
current CPU actually has any other CPU's left in the set of CPU's to be
sent a TLB flush, and not calling down to the IPI code if the mask is
empty.

The reason this started happening at all is that we started passing just
the CPU mask pointers around in commit 4595f9620 ("x86: change
flush_tlb_others to take a const struct cpumask"), and when we did that,
the cpumask was no longer thread-local.

Before that commit, flush_tlb_mm() used to create it's own copy of
'mm->cpu_vm_mask' and pass that copy down to the low-level flush
routines after having tested that it was not empty.  But after changing
it to just pass down the CPU mask pointer, the lower level TLB flush
routines would now get a pointer to that 'mm->cpu_vm_mask', and that
could still change - and become empty - after the test due to other
CPU's having flushed their own TLB's.

See

http://bugzilla.kernel.org/show_bug.cgi?id=13933

for details.

Tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoMake bitmask 'and' operators return a result code
Linus Torvalds [Fri, 21 Aug 2009 16:26:15 +0000]
Make bitmask 'and' operators return a result code

When 'and'ing two bitmasks (where 'andnot' is a variation on it), some
cases want to know whether the result is the empty set or not.  In
particular, the TLB IPI sending code wants to do cpumask operations and
determine if there are any CPU's left in the final set.

So this just makes the bitmask (and cpumask) functions return a boolean
for whether the result has any bits set.

Cc: stable@kernel.org (2.6.30, needed by TLB shootdown fix)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agox86: don't send an IPI to the empty set of CPU's
Linus Torvalds [Fri, 21 Aug 2009 16:23:57 +0000]
x86: don't send an IPI to the empty set of CPU's

The default_send_IPI_mask_logical() function uses the "flat" APIC mode
to send an IPI to a set of CPU's at once, but if that set happens to be
empty, some older local APIC's will apparently be rather unhappy.  So
just warn if a caller gives us an empty mask, and ignore it.

This fixes a regression in 2.6.30.x, due to commit 4595f9620 ("x86:
change flush_tlb_others to take a const struct cpumask"), documented
here:

http://bugzilla.kernel.org/show_bug.cgi?id=13933

which causes a silent lock-up.  It only seems to happen on PPro, P2, P3
and Athlon XP cores.  Most developers sadly (or not so sadly, if you're
a developer..) have more modern CPU's.  Also, on x86-64 we don't use the
flat APIC mode, so it would never trigger there even if the APIC didn't
like sending an empty IPI mask.

Reported-by: Pavel Vilim <wylda@volny.cz>
Reported-and-tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Reported-and-tested-by: Martin Rogge <marogge@onlinehome.de>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agodrm/radeon: add GET_PARAM/INFO support for Z pipes
Alex Deucher [Wed, 19 Aug 2009 23:11:39 +0000]
drm/radeon: add GET_PARAM/INFO support for Z pipes

Needed for occlusion queries on rv530 chips.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agobtrfs: fix inode rbtree corruption
From: Nick Piggin [Fri, 21 Aug 2009 08:09:44 +0000]
btrfs: fix inode rbtree corruption

Node may not be inserted over existing node. This causes inode tree
corruption and I was seeing crashes in inode_tree_del which I can not
reproduce after this patch.

The other way to fix this would be to tie inode lifetime in the rbtree
with inode while not in freeing state. I had a look at this but it is
not so trivial at this point. At least this patch gets things working again.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Chris Mason <chris.mason@oracle.com>
Acked-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

10 years agodrm/radeon/kms: add r100/r200 OQ support.
Dave Airlie [Fri, 21 Aug 2009 00:07:54 +0000]
drm/radeon/kms: add r100/r200 OQ support.

This adds the relocation necessary for OQ support on the r100/r200
chipsets.

Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agodrm: Fix sysfs device confusion.
Thomas Hellstrom [Thu, 20 Aug 2009 09:02:31 +0000]
drm: Fix sysfs device confusion.

The drm sysfs class suspend / resume methods could not distinguish
between different device types wich could lead to illegal type casts.

Use struct device_type and make sure the class suspend / resume callbacks
are aware of those. There is no per device-type suspend / resume. Only
new-style PM.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agodrm/radeon/kms: implement the bo busy ioctl properly.
Dave Airlie [Thu, 20 Aug 2009 23:47:45 +0000]
drm/radeon/kms: implement the bo busy ioctl properly.

The previous patch assumes the ioctl already existed, when
it actually didn't.

It also didn't return the correct error code.

Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agoMerge branch 'i2c-fixes-rc6' of git://aeryn.fluff.org.uk/bjdooks/linux
Linus Torvalds [Thu, 20 Aug 2009 21:55:24 +0000]
Merge branch 'i2c-fixes-rc6' of git://aeryn.fluff.org.uk/bjdooks/linux

* 'i2c-fixes-rc6' of git://aeryn.fluff.org.uk/bjdooks/linux:
  i2c-stu300: I2C STU300 stability updates
  i2c-omap: Enable workaround for Errata 1.153 based on
  i2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts
  i2c-omap: Fix I2C status ACK

10 years agoi2c-stu300: I2C STU300 stability updates
Linus Walleij [Thu, 13 Aug 2009 20:14:23 +0000]
i2c-stu300: I2C STU300 stability updates

- blk clk is enabled when an irq arrives. The clk should be enabled,
  but just to make sure.
- All error bits are handled no matter state machine state
- All irq's will run complete() except for irq's that wasn't an event.
- No more looking into status registers just in case an interrupt
  has happend and the irq handle wasn't executed.
- irq_disable/enable are now separete functions.
- clk settings calculation changed to round upwards instead of
  downwards.
- Number of address send attempts before giving up is increased to 12
  from 10 since it most times take 8 tries before getting through.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

10 years agoi2c-omap: Enable workaround for Errata 1.153 based on
Moiz Sonasath [Thu, 20 Aug 2009 16:21:16 +0000]
i2c-omap: Enable workaround for Errata 1.153 based on

Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later
version of I2C IP block.

The errata impacts OMAP 2420|2430|3430, enable the workaround for these based
on I2C IP block revision number instead of OMAP CPU type

Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

10 years agoi2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts
Moiz Sonasath [Thu, 20 Aug 2009 16:21:15 +0000]
i2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts

ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]

Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

10 years agoi2c-omap: Fix I2C status ACK
Nishanth Menon [Thu, 20 Aug 2009 16:21:14 +0000]
i2c-omap: Fix I2C status ACK

I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

10 years agoMerge branch 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
Linus Torvalds [Thu, 20 Aug 2009 17:19:39 +0000]
Merge branch 'fix/hda' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix probe of Toshiba laptops with ALC268 codec
  ALSA: hda: add model for Intel DG45ID/DG45FC boards
  ALSA: hda: enable speaker output for Compaq 6530s/6531s

10 years agoPCI: check saved state before restore
Alek Du [Sat, 8 Aug 2009 00:46:19 +0000]
PCI: check saved state before restore

Without the check, the config space may be filled with zeros. Though
the driver should try to avoid call restoring before saving, but the
pci layer also should check this.

Also removes the existing check in pci_restore_standard_config, since
it's superfluous with the new check in restore_state.

Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

10 years agoALSA: hda - Fix probe of Toshiba laptops with ALC268 codec
Takashi Iwai [Wed, 19 Aug 2009 18:05:02 +0000]
ALSA: hda - Fix probe of Toshiba laptops with ALC268 codec

There are many variants of Toshiba laptops with ALC268 codec, and
it seems that a few of them don't work with model=toshiba preset
since they have the secondary ALC268 codec just for HDMI output.
This is a regression due to the previous clean-up work to merge all
Toshiba quirk entries into a single check.

This patch adds the identification of such laptops to apply the
standard BIOS-probing method.  Unfortunately, Toshiba laptops have
all the same PCI SSID, so we need to check the codec SSID to identify
each device.

Tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

10 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke...
Linus Torvalds [Wed, 19 Aug 2009 17:40:24 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/ryusuke/nilfs2

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix oopses with doubly mounted snapshots
  nilfs2: missing a read lock for segment writer in nilfs_attach_checkpoint()

10 years agoAFS: Documentation updates
Anton Blanchard [Wed, 19 Aug 2009 15:10:16 +0000]
AFS: Documentation updates

Fix some issues with the AFS documentation, found when testing AFS on ppc64:

- Update AFS features: reading/writing, local caching
- Typo in kafs sysfs debug file
- Use modprobe instead of insmod in example
- Update IPs for grand.central.org

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoMerge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied...
Linus Torvalds [Wed, 19 Aug 2009 17:38:36 +0000]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/kms: teardown crtc correctly when fb is destroyed.
  drm/kms/radeon: cleanup combios TV table like DDX.
  drm/radeon/kms: memset the allocated framebuffer before using it.
  drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it.
  drm/radeon/kms: implement bo busy check + current domain
  drm/radeon/kms: cut down indirects in register accesses.
  drm/radeon/kms: Fix up vertical blank interrupt support.
  drm/radeon/kms: add rv530 R300_SU_REG_DEST + reloc for ZPASS_ADDR
  drm/edid: fixup detailed timings like the X server.
  drm/radeon/kms: Add specific rs690 authorized register table

10 years agoMerge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze
Linus Torvalds [Wed, 19 Aug 2009 16:44:51 +0000]
Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Update Microblaze defconfigs
  microblaze: Use klimit instead of _end for memory init
  microblaze: Enable ppoll syscall
  microblaze: Sane handling of missing timer/intc in device tree
  microblaze: use the generic ack_bad_irq implementation

10 years agoMerge branch 'perfcounters-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux...
Linus Torvalds [Wed, 19 Aug 2009 16:43:19 +0000]
Merge branch 'perfcounters-fixes-for-linus-2' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'perfcounters-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf tools: Make 'make html' work
  perf annotate: Fix segmentation fault
  perf_counter: Fix the PARISC build
  perf_counter: Check task on counter read IPI
  perf: Rename perf-examples.txt to examples.txt
  perf record: Fix typo in pid_synthesize_comm_event

10 years agoALSA: hda: add model for Intel DG45ID/DG45FC boards
Wu Fengguang [Wed, 19 Aug 2009 09:05:11 +0000]
ALSA: hda: add model for Intel DG45ID/DG45FC boards

The BIOS pin configs are in fact correct and shall not be overwritten.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

10 years agoALSA: hda: enable speaker output for Compaq 6530s/6531s
Wu Fengguang [Wed, 19 Aug 2009 08:58:59 +0000]
ALSA: hda: enable speaker output for Compaq 6530s/6531s

HP Compaq 6530s and 6531s internal speaker is silence or becomes silence
within 1 minute after fresh boot. It is found that pin 0x1c must be set to
PIN_OUT mode to make the speaker work. This is weird - line-in pin 0x1c and
speaker pin 0x16 seem to be unrelated.

The codec differences before/after patch are:

@@ Node 0x17 [Pin Complex] wcaps 0x40020b:
   Pin Default 0x41a6e130: [N/A] Mic at Ext Rear
     Conn = Digital, Color = White
     DefAssociation = 0x3, Sequence = 0x0
     Misc = NO_PRESENCE
-  Pin-ctls: 0x24: IN
+  Pin-ctls: 0x40: OUT
@@ Node 0x1c [Pin Complex] wcaps 0x40018d:
   Pin Default 0x41813021: [N/A] Line In at Ext Rear
     Conn = 1/8, Color = Blue
     DefAssociation = 0x2, Sequence = 0x1
-  Pin-ctls: 0x24: IN VREF_80
+  Pin-ctls: 0x40: OUT VREF_HIZ
   Unsolicited: tag=00, enabled=0
   Connection: 1
      0x24

Tests show that it won't impact (external) Mic recording.

Reported-by: "Lin, Ming M" <ming.m.lin@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

10 years agodrm/kms: teardown crtc correctly when fb is destroyed.
Dave Airlie [Mon, 17 Aug 2009 03:11:23 +0000]
drm/kms: teardown crtc correctly when fb is destroyed.

If userspace destroys a framebuffer that is in use on a crtc,
don't just null it out, tear down the crtc properly so the
hw gets turned off.

Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agodrm/kms/radeon: cleanup combios TV table like DDX.
Dave Airlie [Mon, 17 Aug 2009 00:19:51 +0000]
drm/kms/radeon: cleanup combios TV table like DDX.

The fallback case wasn't getting executed properly if there
was no TV table, which my T42 M7 hasn't got.

Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agodrm/radeon/kms: memset the allocated framebuffer before using it.
Dave Airlie [Mon, 17 Aug 2009 00:20:47 +0000]
drm/radeon/kms: memset the allocated framebuffer before using it.

This gets rid of some ugliness, we shuold probably find a way
for the GPU to zero this.

Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agodrm/radeon/kms: although LVDS might be possible on crtc 1 don't do it.
Dave Airlie [Mon, 17 Aug 2009 00:22:37 +0000]
drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it.

LVDS always requests RMX_FULL, we need to fix it so that doesn't happen
before we can enable LVDS on crtc 1.

Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris...
Linus Torvalds [Wed, 19 Aug 2009 02:41:47 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  security: Fix prompt for LSM_MMAP_MIN_ADDR
  security: Make LSM_MMAP_MIN_ADDR default match its help text.

10 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Linus Torvalds [Wed, 19 Aug 2009 02:41:05 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/tj/percpu

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: use the right flag for get_vm_area()
  percpu, sparc64: fix sparse possible cpu map handling
  init: set nr_cpu_ids before setup_per_cpu_areas()

10 years agoMerge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Tue, 18 Aug 2009 23:55:43 +0000]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, mce: Don't initialize MCEs on unknown CPUs
  x86, mce: don't log boot MCEs on Pentium M (model == 13) CPUs
  x86: Annotate section mismatch warnings in kernel/apic/x2apic_uv_x.c
  x86, mce: therm_throt: Don't log redundant normality
  x86: Fix UV BAU destination subnode id

10 years agomm: build_zonelists(): move clear node_load[] to __build_all_zonelists()
Bo Liu [Tue, 18 Aug 2009 21:11:19 +0000]
mm: build_zonelists(): move clear node_load[] to __build_all_zonelists()

If node_load[] is cleared everytime build_zonelists() is
called,node_load[] will have no help to find the next node that should
appear in the given node's fallback list.

Because of the bug, zonelist's node_order is not calculated as expected.
This bug affects on big machine, which has asynmetric node distance.

[synmetric NUMA's node distance]
     0    1    2
0   10   12   12
1   12   10   12
2   12   12   10

[asynmetric NUMA's node distance]
     0    1    2
0   10   12   20
1   12   10   14
2   20   14   10

This (my bug) is very old but no one has reported this for a long time.
Maybe because the number of asynmetric NUMA is very small and they use
cpuset for customizing node memory allocation fallback.

[akpm@linux-foundation.org: fix CONFIG_NUMA=n build]
Signed-off-by: Bo Liu <bo-liu@hotmail.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoREPORTING-BUGS: add get_maintainer.pl blurb
Joe Perches [Tue, 18 Aug 2009 21:11:18 +0000]
REPORTING-BUGS: add get_maintainer.pl blurb

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agonommu: check fd read permission in validate_mmap_request()
Graff Yang [Tue, 18 Aug 2009 21:11:17 +0000]
nommu: check fd read permission in validate_mmap_request()

According to the POSIX (1003.1-2008), the file descriptor shall have been
opened with read permission, regardless of the protection options specified to
mmap().  The ltp test cases mmap06/07 need this.

Signed-off-by: Graff Yang <graff.yang@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agospi_s3c24xx: fix transfer setup code
Ben Dooks [Tue, 18 Aug 2009 21:11:17 +0000]
spi_s3c24xx: fix transfer setup code

Since the changes to the bitbang driver, there is the possibility we will
be called with either the speed_hz or bpw values zero.  We take these to
mean that the default values (8 bits per word, or maximum bus speed).

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agospi_s3c24xx: fix clock rate calculation
Ben Dooks [Tue, 18 Aug 2009 21:11:16 +0000]
spi_s3c24xx: fix clock rate calculation

Currently the clock rate calculation may round as pleased, which means
that it is possible that we will round down and end up with a faster clock
rate than intended.

Change the calculation to use DIV_ROUND_UP() to ensure that we end up with
a clock rate either the same as or lower than the user requested one.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agommc: add the new linux-mmc mailing list to MAINTAINERS
Andrew Morton [Tue, 18 Aug 2009 21:11:12 +0000]
mmc: add the new linux-mmc mailing list to MAINTAINERS

There are a number of individual MMC drivers listed in MAINTAINERS.  I
didn't modify those records.  Perhaps I should have.

Cc: <linux-mmc@vger.kernel.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Pavel Pisa <ppisa@pikron.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Sascha Sommer <saschasommer@freenet.de>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agomm: revert "oom: move oom_adj value"
KOSAKI Motohiro [Tue, 18 Aug 2009 21:11:10 +0000]
mm: revert "oom: move oom_adj value"

The commit 2ff05b2b (oom: move oom_adj value) moveed the oom_adj value to
the mm_struct.  It was a very good first step for sanitize OOM.

However Paul Menage reported the commit makes regression to his job
scheduler.  Current OOM logic can kill OOM_DISABLED process.

Why? His program has the code of similar to the following.

...
set_oom_adj(OOM_DISABLE); /* The job scheduler never killed by oom */
...
if (vfork() == 0) {
set_oom_adj(0); /* Invoked child can be killed */
execve("foo-bar-cmd");
}
....

vfork() parent and child are shared the same mm_struct.  then above
set_oom_adj(0) doesn't only change oom_adj for vfork() child, it's also
change oom_adj for vfork() parent.  Then, vfork() parent (job scheduler)
lost OOM immune and it was killed.

Actually, fork-setting-exec idiom is very frequently used in userland program.
We must not break this assumption.

Then, this patch revert commit 2ff05b2b and related commit.

Reverted commit list
---------------------
- commit 2ff05b2b4e (oom: move oom_adj value from task_struct to mm_struct)
- commit 4d8b9135c3 (oom: avoid unnecessary mm locking and scanning for OOM_DISABLE)
- commit 8123681022 (oom: only oom kill exiting tasks with attached memory)
- commit 933b787b57 (mm: copy over oom_adj value at fork time)

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agovfs: make get_sb_pseudo set s_maxbytes to value that can be cast to signed
Jeff Layton [Tue, 18 Aug 2009 21:11:08 +0000]
vfs: make get_sb_pseudo set s_maxbytes to value that can be cast to signed

get_sb_pseudo sets s_maxbytes to ~0ULL which becomes negative when cast
to a signed value.  Fix it to use MAX_LFS_FILESIZE which casts properly
to a positive signed value.

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Steve French <smfrench@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Robert Love <rlove@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoMAINTAINERS: OSD LIBRARY and FILESYSTEM pattern fix
Joe Perches [Tue, 18 Aug 2009 21:11:06 +0000]
MAINTAINERS: OSD LIBRARY and FILESYSTEM pattern fix

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Benny Halevy <bhalevy@panasas.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agosecurity: Fix prompt for LSM_MMAP_MIN_ADDR
Andreas Schwab [Tue, 18 Aug 2009 20:14:29 +0000]
security: Fix prompt for LSM_MMAP_MIN_ADDR

Fix prompt for LSM_MMAP_MIN_ADDR.

(Verbs are cool!)

Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>

10 years agosecurity: Make LSM_MMAP_MIN_ADDR default match its help text.
Dave Jones [Tue, 18 Aug 2009 17:47:37 +0000]
security: Make LSM_MMAP_MIN_ADDR default match its help text.

Commit 788084aba2ab7348257597496befcbccabdc98a3 added the LSM_MMAP_MIN_ADDR
option, whose help text states "For most ia64, ppc64 and x86 users with lots
of address space a value of 65536 is reasonable and should cause no problems."
Which implies that it's default setting was typoed.

Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>

10 years agoMerge branch 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Tue, 18 Aug 2009 20:57:38 +0000]
Merge branch 'irq-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Wake up irq thread after action has been installed

10 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Tue, 18 Aug 2009 20:55:01 +0000]
Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (60 commits)
  net: restore gnet_stats_basic to previous definition
  NETROM: Fix use of static buffer
  e1000e: fix use of pci_enable_pcie_error_reporting
  e1000e: WoL does not work on 82577/82578 with manageability enabled
  cnic: Fix locking in init/exit calls.
  cnic: Fix locking in start/stop calls.
  bnx2: Use mutex on slow path cnic calls.
  cnic: Refine registration with bnx2.
  cnic: Fix symbol_put_addr() panic on ia64.
  gre: Fix MTU calculation for bound GRE tunnels
  pegasus: Add new device ID.
  drivers/net: fixed drivers that support netpoll use ndo_start_xmit()
  via-velocity: Fix test of mii_status bit VELOCITY_DUPLEX_FULL
  rt2x00: fix memory corruption in rf cache, add a sanity check
  ixgbe: Fix receive on real device when VLANs are configured
  ixgbe: Do not return 0 in ixgbe_fcoe_ddp() upon FCP_RSP in DDP completion
  netxen: free napi resources during detach
  netxen: remove netxen workqueue
  ixgbe: fix issues setting rx-usecs with legacy interrupts
  can: fix oops caused by wrong rtnl newlink usage
  ...

10 years agoMerge branch 'sh/for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal...
Linus Torvalds [Tue, 18 Aug 2009 20:54:26 +0000]
Merge branch 'sh/for-2.6.31' of git://git./linux/kernel/git/lethal/sh-2.6

* 'sh/for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: sh7724 ddr self-refresh changes
  sh: use in-soc KEYSC on se7724
  sh: CMT suspend/resume
  sh: skip disabled LCDC channels

10 years agoMerge branch 'for-linus' of git://neil.brown.name/md
Linus Torvalds [Tue, 18 Aug 2009 20:54:08 +0000]
Merge branch 'for-linus' of git://neil.brown.name/md

* 'for-linus' of git://neil.brown.name/md:
  Fix new incorrect error return from do_md_stop.

10 years agonilfs2: fix oopses with doubly mounted snapshots
Ryusuke Konishi [Tue, 18 Aug 2009 15:29:43 +0000]
nilfs2: fix oopses with doubly mounted snapshots

will fix kernel oopses like the following:

 # mount -t nilfs2 -r -o cp=20 /dev/sdb1 /test1
 # mount -t nilfs2 -r -o cp=20 /dev/sdb1 /test2
 # umount /test1
 # umount /test2

BUG: sleeping function called from invalid context at arch/x86/mm/fault.c:1069
in_atomic(): 0, irqs_disabled(): 1, pid: 3886, name: umount.nilfs2
1 lock held by umount.nilfs2/3886:
 #0:  (&type->s_umount_key#31){+.+...}, at: [<c10b398a>] deactivate_super+0x52/0x6c
irq event stamp: 1219
hardirqs last  enabled at (1219): [<c135c774>] __mutex_unlock_slowpath+0xf8/0x119
hardirqs last disabled at (1218): [<c135c6d5>] __mutex_unlock_slowpath+0x59/0x119
softirqs last  enabled at (1214): [<c1033316>] __do_softirq+0x1a5/0x1ad
softirqs last disabled at (1205): [<c1033354>] do_softirq+0x36/0x5a
Pid: 3886, comm: umount.nilfs2 Not tainted 2.6.31-rc6 #55
Call Trace:
 [<c1023549>] __might_sleep+0x107/0x10e
 [<c13603c0>] do_page_fault+0x246/0x397
 [<c136017a>] ? do_page_fault+0x0/0x397
 [<c135e753>] error_code+0x6b/0x70
 [<c136017a>] ? do_page_fault+0x0/0x397
 [<c104f805>] ? __lock_acquire+0x91/0x12fd
 [<c1050a62>] ? __lock_acquire+0x12ee/0x12fd
 [<c1050a62>] ? __lock_acquire+0x12ee/0x12fd
 [<c1050b2b>] lock_acquire+0xba/0xdd
 [<d0d17d3f>] ? nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
 [<c135d4fe>] down_write+0x2a/0x46
 [<d0d17d3f>] ? nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
 [<d0d17d3f>] nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
 [<c104ea2c>] ? mark_held_locks+0x43/0x5b
 [<c104ecb1>] ? trace_hardirqs_on_caller+0x10b/0x133
 [<c104ece4>] ? trace_hardirqs_on+0xb/0xd
 [<d0d09ac1>] nilfs_put_super+0x2f/0xca [nilfs2]
 [<c10b3352>] generic_shutdown_super+0x49/0xb8
 [<c10b33de>] kill_block_super+0x1d/0x31
 [<c10e6599>] ? vfs_quota_off+0x0/0x12
 [<c10b398f>] deactivate_super+0x57/0x6c
 [<c10c4bc3>] mntput_no_expire+0x8c/0xb4
 [<c10c5094>] sys_umount+0x27f/0x2a4
 [<c10c50c6>] sys_oldumount+0xd/0xf
 [<c10031a4>] sysenter_do_call+0x12/0x38
 ...

This turns out to be a bug brought by an -rc1 patch ("nilfs2: simplify
remaining sget() use").

In the patch, a new "put resource" function, nilfs_put_sbinfo()
was introduced to delay freeing nilfs_sb_info struct.

But the nilfs_put_sbinfo() mistakenly used atomic_dec_and_test()
function to check the reference count, and it caused the nilfs_sb_info
was freed when user mounted a snapshot twice.

This bug also suggests there was unseen memory leak in usual mount
/umount operations for nilfs.

Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>

10 years agoperf tools: Make 'make html' work
Kyle McMartin [Tue, 18 Aug 2009 16:41:25 +0000]
perf tools: Make 'make html' work

pushd tools/perf/Documentation
make html
popd

is failing for me...

    ASCIIDOC perf-annotate.html
ERROR: unsafe: include file: /etc/asciidoc/./stylesheets/xhtml11.css
ERROR: unsafe: include file:
/etc/asciidoc/./stylesheets/xhtml11-manpage.css
ERROR: unsafe: include file:
/etc/asciidoc/./stylesheets/xhtml11-quirks.css
make: *** [perf-annotate.html] Error 1

Apparently asciidoc "unsafe" is the default mode of operation
in practice.

https://bugzilla.redhat.com/show_bug.cgi?id=506953

Works tidily now.

Signed-off-by: Kyle McMartin <kyle@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090818164125.GM25206@bombadil.infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

10 years agogenirq: Wake up irq thread after action has been installed
Thomas Gleixner [Mon, 17 Aug 2009 12:07:16 +0000]
genirq: Wake up irq thread after action has been installed

The wake_up_process() of the new irq thread in __setup_irq() is too
early as the irqaction is not yet fully initialized especially
action->irq is not yet set. The interrupt thread might dereference the
wrong irq descriptor.

Move the wakeup after the action is installed and action->irq has been
set.

Reported-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Buesch <mb@bu3sch.de>

10 years agoperf annotate: Fix segmentation fault
Ingo Molnar [Tue, 18 Aug 2009 11:52:28 +0000]
perf annotate: Fix segmentation fault

Linus reported this perf annotate segfault:

        [torvalds@nehalem git]$ perf annotate unmap_vmas
        Segmentation fault

        #0  map__clone (self=<value optimized out>) at builtin-annotate.c:236
        #1  thread__fork (self=<value optimized out>) at builtin-annotate.c:372

The bug here was that builtin-annotate.c was a copy of
builtin-report.c and a threading related fix to builtin-report.c
didnt get propagated to builtin-annotate.c ...

Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

10 years agoperf_counter: Fix the PARISC build
Ingo Molnar [Tue, 18 Aug 2009 09:32:24 +0000]
perf_counter: Fix the PARISC build

PARISC does not build:

/home/mingo/tip/kernel/perf_counter.c: In function 'perf_counter_index':
/home/mingo/tip/kernel/perf_counter.c:2016: error: 'PERF_COUNTER_INDEX_OFFSET' undeclared (first use in this function)
/home/mingo/tip/kernel/perf_counter.c:2016: error: (Each undeclared identifier is reported only once
/home/mingo/tip/kernel/perf_counter.c:2016: error: for each function it appears in.)

As PERF_COUNTER_INDEX_OFFSET is not defined.

Now, we could define it in the architecture - but lets also provide
a core default of 0 (which happens to be what all but one
architecture uses at the moment).

Architectures that need a different index offset should set this
value in their asm/perf_counter.h files.

Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

10 years agomicroblaze: Update Microblaze defconfigs
Michal Simek [Tue, 18 Aug 2009 09:05:11 +0000]
microblaze: Update Microblaze defconfigs

Signed-off-by: Michal Simek <monstr@monstr.eu>

10 years agomicroblaze: Use klimit instead of _end for memory init
Michal Simek [Tue, 11 Aug 2009 10:36:12 +0000]
microblaze: Use klimit instead of _end for memory init

For noMMU system when you use larger rootfs image
there is problem with using _end label because
we increase klimit but in memory initialization
we use still _end which is wrong. Larger mtd rootfs
was rewritten by init_bootmem_node.

MMU kernel use static initialization where klimit
is setup to _end. There is no any other hanling
with klimit.

Signed-off-by: Michal Simek <monstr@monstr.eu>

10 years agomicroblaze: Enable ppoll syscall
Michal Simek [Thu, 6 Aug 2009 14:00:52 +0000]
microblaze: Enable ppoll syscall

Signed-off-by: Michal Simek <monstr@monstr.eu>

10 years agomicroblaze: Sane handling of missing timer/intc in device tree
John Williams [Wed, 29 Jul 2009 12:08:40 +0000]
microblaze: Sane handling of missing timer/intc in device tree

This code path doesn't test any returned pointers for NULL, leading to a bad
kernel page fault if there's no timer/intc found.

Slightly better is to BUG(), but even better still would be a printk beforehand.

Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>

10 years agomicroblaze: use the generic ack_bad_irq implementation
Christoph Hellwig [Thu, 6 Aug 2009 21:00:38 +0000]
microblaze: use the generic ack_bad_irq implementation

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michal Simek <monstr@monstr.eu>

10 years agonilfs2: missing a read lock for segment writer in nilfs_attach_checkpoint()
Zhang Qiang [Tue, 18 Aug 2009 06:58:24 +0000]
nilfs2: missing a read lock for segment writer in nilfs_attach_checkpoint()

'ns_cno' of structure 'the_nilfs' must be protected from segment
writer, in other words, the caller of nilfs_get_checkpoint should hold
read lock for nilfs->ns_segctor_sem.  This patch adds the lock/unlock
operations in nilfs_attach_checkpoint() when calling
nilfs_cpfile_get_checkpoint().

Signed-off-by: Zhang Qiang <zhangqiang.buaa@gmail.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>

10 years agonet: restore gnet_stats_basic to previous definition
Eric Dumazet [Sun, 16 Aug 2009 09:36:49 +0000]
net: restore gnet_stats_basic to previous definition

In 5e140dfc1fe87eae27846f193086724806b33c7d "net: reorder struct Qdisc
for better SMP performance" the definition of struct gnet_stats_basic
changed incompatibly, as copies of this struct are shipped to
userland via netlink.

Restoring old behavior is not welcome, for performance reason.

Fix is to use a private structure for kernel, and
teach gnet_stats_copy_basic() to convert from kernel to user land,
using legacy structure (struct gnet_stats_basic)

Based on a report and initial patch from Michael Spang.

Reported-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoNETROM: Fix use of static buffer
Ralf Baechle [Tue, 18 Aug 2009 01:05:32 +0000]
NETROM: Fix use of static buffer

The static variable used by nr_call_to_digi might result in corruption if
multiple threads are trying to usee a node or neighbour via ioctl.  Fixed
by having the caller pass a structure in.  This is safe because nr_add_node
rsp. nr_add_neigh will allocate a permanent structure, if needed.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>