8 years agohwmon: (w83795) Clear intrusion alarm immediately
Jean Delvare [Mon, 15 Nov 2010 20:38:57 +0000]
hwmon: (w83795) Clear intrusion alarm immediately

When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

8 years agohwmon: (w83795) Read the intrusion state properly
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000]
hwmon: (w83795) Read the intrusion state properly

We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)

So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

8 years agohwmon: (w83795) Print the actual temperature channels as sources
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000]
hwmon: (w83795) Print the actual temperature channels as sources

Don't expose raw register values to user-space. Decode and encode
temperature channels selected as temperature sources as needed.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

8 years agohwmon: (w83795) List all usable temperature sources
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000]
hwmon: (w83795) List all usable temperature sources

Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

8 years agohwmon: (w83795) Expose fan control method
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000]
hwmon: (w83795) Expose fan control method

Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

8 years agohwmon: (w83795) Fix fan control mode attributes
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000]
hwmon: (w83795) Fix fan control mode attributes

There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
  It will be added back as a separate attribute, as per the standard
  sysfs interface.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

8 years agohwmon: (lm95241) Check validity of input values
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000]
hwmon: (lm95241) Check validity of input values

This clears the following build-time warnings I was seeing:

drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result

This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>

8 years agohwmon: Change mail address of Hans J. Koch
Hans J. Koch [Mon, 15 Nov 2010 20:38:56 +0000]
hwmon: Change mail address of Hans J. Koch

My old mail address doesn't exist anymore. This changes all occurrences
to my new address.

Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

8 years agoMerge branch 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
Linus Torvalds [Sat, 13 Nov 2010 18:00:15 +0000]
Merge branch 'urgent' of git://git./linux/kernel/git/brodo/pcmcia-2.6

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
  drivers/pcmcia/soc_common.c: Use printf extension %pV
  pcmcia: fix warning in synclink driver
  pcmcia/sa1100: don't put machine specific init functions in .init.text
  pcmcia/cm4000: fix error code
  pd6729: Coding Style fixes

8 years agoRevert "8250: Fix tcsetattr to avoid ioctl(TIOCMIWAIT) hang"
Ingo Molnar [Sat, 13 Nov 2010 15:21:58 +0000]
Revert "8250: Fix tcsetattr to avoid ioctl(TIOCMIWAIT) hang"

This reverts commit 47d3904fe40d62deee8cd46e79ca784e7a548acd.

Crashes any x86 serial console bootup:

  Console: colour VGA+ 80x25
  BUG: unable to handle kernel NULL pointer dereference at 0000000000000158
  IP: [<ffffffff811ebcb4>] serial8250_do_set_termios+0x1d4/0x430
  ...

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Greg KH <gregkh@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Linus Torvalds [Sat, 13 Nov 2010 17:55:56 +0000]
Merge git://git./linux/kernel/git/herbert/crypto-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: padlock - Fix AES-CBC handling on odd-block-sized input
  crypto: n2 - dubious error check

8 years agoMerge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab...
Linus Torvalds [Sat, 13 Nov 2010 17:55:19 +0000]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] soc-camera: Compile fixes for mx2-camera
  [media] SoC Camera: ov6650: minor cleanups
  [media] SOC Camera: OMAP1: typo fix
  [media] SoC Camera: OMAP1: update for recent videobuf changes
  [media] SoC Camera: OMAP1: update for recent framework changes
  [media] ARM mx3_camera: check for DMA engine type
  [media] tm6000: bugfix set tv standards
  [media] cafe_ccic: fix subdev configuration
  [media] saa7134: Fix autodetect for Behold A7 and H7 TV cards
  [media] v4l: kill the BKL
  [media] BZ#22292: dibx000_common: Restore i2c algo pointer

8 years agoi8k: Tell gcc that *regs gets clobbered
Jim Bos [Sat, 13 Nov 2010 11:13:53 +0000]
i8k: Tell gcc that *regs gets clobbered

More recent GCC caused the i8k driver to stop working, on Slackware
compiler was upgraded from gcc-4.4.4 to gcc-4.5.1 after which it didn't
work anymore, meaning the driver didn't load or gave total nonsensical
output.

As it turned out the asm(..) statement forgot to mention it modifies the
*regs variable.

Credits to Andi Kleen and Andreas Schwab for providing the fix.

Signed-off-by: Jim Bos <jim876@xs4all.nl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoACPI: debugfs custom_method open to non-root
Dave Jones [Sat, 13 Nov 2010 05:58:54 +0000]
ACPI: debugfs custom_method open to non-root

Currently we have:

  --w--w--w-. 1 root root 0 2010-11-11 14:56 /sys/kernel/debug/acpi/custom_method

which is just crazy. Change this to --w-------.

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: stable@kernel.org (for 2.6.36)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Sat, 13 Nov 2010 01:17:55 +0000]
Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
  can-bcm: fix minor heap overflow
  gianfar: Do not call device_set_wakeup_enable() under a spinlock
  ipv6: Warn users if maximum number of routes is reached.
  docs: Add neigh/gc_thresh3 and route/max_size documentation.
  axnet_cs: fix resume problem for some Ax88790 chip
  ipv6: addrconf: don't remove address state on ifdown if the address is being kept
  tcp: Don't change unlocked socket state in tcp_v4_err().
  x25: Prevent crashing when parsing bad X.25 facilities
  cxgb4vf: add call to Firmware to reset VF State.
  cxgb4vf: Fail open if link_start() fails.
  cxgb4vf: flesh out PCI Device ID Table ...
  cxgb4vf: fix some errors in Gather List to skb conversion
  cxgb4vf: fix bug in Generic Receive Offload
  cxgb4vf: don't implement trivial (and incorrect) ndo_select_queue()
  ixgbe: Look inside vlan when determining offload protocol.
  bnx2x: Look inside vlan when determining checksum proto.
  vlan: Add function to retrieve EtherType from vlan packets.
  virtio-net: init link state correctly
  ucc_geth: Fix deadlock
  ucc_geth: Do not bring the whole IF down when TX failure.
  ...

8 years agoMerge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzi...
Linus Torvalds [Sat, 13 Nov 2010 01:17:09 +0000]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  drivers/ata/pata_octeon_cf.c: delete double assignment
  pata_legacy: fix CONFIG_PATA_WINBOND_VLB_MODULE test
  libata: fix NULL sdev dereference race in atapi_qc_complete()

8 years agoMerge branch 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh...
Linus Torvalds [Sat, 13 Nov 2010 01:14:20 +0000]
Merge branch 'staging-linus' of git://git./linux/kernel/git/gregkh/staging-2.6

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (38 commits)
  Revert "staging: tidspbridge: replace iommu custom for opensource implementation"
  Revert "staging: tidspbridge - move shared memory iommu maps to tiomap3430.c"
  Revert "staging: tidspbridge - rename bridge_brd_mem_map/unmap to a proper name"
  Revert "staging: tidspbridge - remove custom mmu code from tiomap3430.c"
  Revert "staging: tidspbridge - fix mmufault support"
  Revert "staging: tidspbridge - remove hw directory"
  Revert "staging: tidspbridge - move all iommu related code to a new file"
  Revert "staging: tidspbridge: remove dw_dmmu_base from cfg_hostres struct"
  Revert "staging: tidspbridge - remove reserved memory clean up"
  Revert "staging: tidspbridge - deprecate reserve/unreserve_memory funtions"
  Revert "staging: tidspbridge - remove dmm custom module"
  Revert "staging: tidspbridge - update Kconfig to select IOMMU module"
  staging: tidspbridge: hardcode SCM macros while fix is upstreamed
  Staging: keucr driver: fix uninitialized variable & proper memset length
  omap: dsp: remove shm from normal memory
  Staging: wlan-ng: Fix wrong #ifdef #endif sequence
  Staging: Update parameters for cfg80211 key management operation
  Staging: ath6kl: Fix pointer casts on 64-bit architectures
  Staging: batman-adv: suppress false warning when changing the mac address
  Staging: batman-adv: fix interface alternating and bonding reggression
  ...

8 years agoMerge branch 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh...
Linus Torvalds [Sat, 13 Nov 2010 01:13:28 +0000]
Merge branch 'usb-linus' of git://git./linux/kernel/git/gregkh/usb-2.6

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (28 commits)
  Revert "USB: xhci: Use GFP_ATOMIC under spin_lock"
  USB: ohci-jz4740: Fix spelling in MODULE_ALIAS
  UWB: Return UWB_RSV_ALLOC_NOT_FOUND rather than crashing on NULL dereference if kzalloc fails
  usb: core: fix information leak to userland
  usb: misc: iowarrior: fix information leak to userland
  usb: misc: sisusbvga: fix information leak to userland
  usb: subtle increased memory usage in u_serial
  USB: option: fix when the driver is loaded incorrectly for some Huawei devices.
  USB: xhci: Use GFP_ATOMIC under spin_lock
  usb: gadget: goku_udc: add registered flag bit, fixing build
  USB: ehci/mxc: compile fix
  USB: Fix FSL USB driver on non Open Firmware systems
  USB: the development of the usb tree is now in git
  usb: musb: fail unaligned DMA transfers on v1.8 and above
  USB: ftdi_sio: add device IDs for Milkymist One JTAG/serial
  usb.h: fix ioctl kernel-doc info
  usb: musb: gadget: kill duplicate code in musb_gadget_queue()
  usb: musb: Fix handling of spurious SESSREQ
  usb: musb: fix kernel oops when loading musb_hdrc module for the 2nd time
  USB: musb: blackfin: push clkin value to platform resources
  ...

8 years agoMerge branch 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh...
Linus Torvalds [Sat, 13 Nov 2010 00:02:30 +0000]
Merge branch 'tty-linus' of git://git./linux/kernel/git/gregkh/tty-2.6

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  n_gsm: Fix length handling
  n_gsm: Copy n2 over when configuring via ioctl interface
  serial: bfin_5xx: grab port lock before making port termios changes
  serial: bfin_5xx: disable CON_PRINTBUFFER for consoles
  serial: bfin_5xx: remove redundant SSYNC to improve TX speed
  serial: bfin_5xx: always include DMA headers
  vcs: make proper usage of the poll flags
  amiserial: Remove unused variable icount
  8250: Fix tcsetattr to avoid ioctl(TIOCMIWAIT) hang
  tty_ldisc: Fix BUG() on hangup
  TTY: restore tty_ldisc_wait_idle
  SERIAL: blacklist si3052 chip
  drivers/serial/bfin_5xx.c: Fix line continuation defects
  tty: prevent DOS in the flush_to_ldisc
  8250: add support for Kouwell KW-L221N-2
  nozomi: Fix warning from the previous TIOCGCOUNT changes
  tty: fix warning in synclink driver
  tty: Fix formatting in tty.h
  tty: the development tree is now done in git

8 years agoMerge branch 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen
Linus Torvalds [Sat, 13 Nov 2010 00:01:55 +0000]
Merge branch 'upstream/core' of git://git./linux/kernel/git/jeremy/xen

* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
  xen: do not release any memory under 1M in domain 0
  xen: events: do not unmask event channels on resume
  xen: correct size of level2_kernel_pgt

8 years agoMerge branch 'stable/xen-pcifront-fixes' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Fri, 12 Nov 2010 23:54:39 +0000]
Merge branch 'stable/xen-pcifront-fixes' of git://git./linux/kernel/git/konrad/xen

* 'stable/xen-pcifront-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  MAINTAINERS: Mark XEN lists as moderated
  xen-pcifront: fix PCI reference leak
  xen-pcifront: Remove duplicate inclusion of headers.
  xen: fix memory leak in Xen PCI MSI/MSI-X allocator.
  MAINTAINERS: Update mailing list name for Xen pieces.

8 years agodrivers/ata/pata_octeon_cf.c: delete double assignment
Julia Lawall [Tue, 26 Oct 2010 10:25:43 +0000]
drivers/ata/pata_octeon_cf.c: delete double assignment

Delete successive assignments to the same location.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression i;
@@

*i = ...;
 i = ...;
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

8 years agopata_legacy: fix CONFIG_PATA_WINBOND_VLB_MODULE test
Tejun Heo [Fri, 12 Nov 2010 11:01:41 +0000]
pata_legacy: fix CONFIG_PATA_WINBOND_VLB_MODULE test

pata_legacy is incorrectly testing PATA_WINBOND_VLB_MODULE instead of
CONFIG_PATA_WINBOND_VLB_MODULE.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "Robert P. J. Day" <rpjday@crashcourse.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

8 years agolibata: fix NULL sdev dereference race in atapi_qc_complete()
Tejun Heo [Mon, 1 Nov 2010 10:39:19 +0000]
libata: fix NULL sdev dereference race in atapi_qc_complete()

SCSI commands may be issued between __scsi_add_device() and dev->sdev
assignment, so it's unsafe for ata_qc_complete() to dereference
dev->sdev->locked without checking whether it's NULL or not.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

8 years agocan-bcm: fix minor heap overflow
Oliver Hartkopp [Wed, 10 Nov 2010 12:10:30 +0000]
can-bcm: fix minor heap overflow

On 64-bit platforms the ASCII representation of a pointer may be up to 17
bytes long. This patch increases the length of the buffer accordingly.

http://marc.info/?l=linux-netdev&m=128872251418192&w=2

Reported-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agogianfar: Do not call device_set_wakeup_enable() under a spinlock
Rafael J. Wysocki [Tue, 9 Nov 2010 11:54:19 +0000]
gianfar: Do not call device_set_wakeup_enable() under a spinlock

The gianfar driver calls device_set_wakeup_enable() under a spinlock,
which causes a problem to happen after the recent core power
management changes, because this function can sleep now.  Fix this
by moving the device_set_wakeup_enable() call out of the
spinlock-protected area.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoipv6: Warn users if maximum number of routes is reached.
Ben Greear [Mon, 8 Nov 2010 12:33:48 +0000]
ipv6: Warn users if maximum number of routes is reached.

This gives users at least some clue as to what the problem
might be and how to go about fixing it.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agodocs: Add neigh/gc_thresh3 and route/max_size documentation.
Ben Greear [Mon, 8 Nov 2010 09:13:48 +0000]
docs: Add neigh/gc_thresh3 and route/max_size documentation.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoaxnet_cs: fix resume problem for some Ax88790 chip
Ken Kawasaki [Sat, 6 Nov 2010 05:11:24 +0000]
axnet_cs: fix resume problem for some Ax88790 chip

axnet_cs:
    Some Ax88790 chip need to reinitialize the CISREG_CCSR register
    after resume.

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoipv6: addrconf: don't remove address state on ifdown if the address is being kept
Lorenzo Colitti [Wed, 27 Oct 2010 18:16:49 +0000]
ipv6: addrconf: don't remove address state on ifdown if the address is being kept

Currently, addrconf_ifdown does not delete statically configured IPv6
addresses when the interface is brought down. The intent is that when
the interface comes back up the address will be usable again. However,
this doesn't actually work, because the system stops listening on the
corresponding solicited-node multicast address, so the address cannot
respond to neighbor solicitations and thus receive traffic. Also, the
code notifies the rest of the system that the address is being deleted
(e.g, RTM_DELADDR), even though it is not. Fix it so that none of this
state is updated if the address is being kept on the interface.

Tested: Added a statically configured IPv6 address to an interface,
started ping, brought link down, brought link up again. When link came
up ping kept on going and "ip -6 maddr" showed that the host was still
subscribed to there

Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agotcp: Don't change unlocked socket state in tcp_v4_err().
David S. Miller [Fri, 12 Nov 2010 21:35:00 +0000]
tcp: Don't change unlocked socket state in tcp_v4_err().

Alexey Kuznetsov noticed a regression introduced by
commit f1ecd5d9e7366609d640ff4040304ea197fbc618
("Revert Backoff [v3]: Revert RTO on ICMP destination unreachable")

The RTO and timer modification code added to tcp_v4_err()
doesn't check sock_owned_by_user(), which if true means we
don't have exclusive access to the socket and therefore cannot
modify it's critical state.

Just skip this new code block if sock_owned_by_user() is true
and eliminate the now superfluous sock_owned_by_user() code
block contained within.

Reported-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>

8 years agox25: Prevent crashing when parsing bad X.25 facilities
Dan Rosenberg [Fri, 12 Nov 2010 20:44:42 +0000]
x25: Prevent crashing when parsing bad X.25 facilities

Now with improved comma support.

On parsing malformed X.25 facilities, decrementing the remaining length
may cause it to underflow.  Since the length is an unsigned integer,
this will result in the loop continuing until the kernel crashes.

This patch adds checks to ensure decrementing the remaining length does
not cause it to wrap around.

Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agocxgb4vf: add call to Firmware to reset VF State.
Casey Leedom [Thu, 11 Nov 2010 09:06:53 +0000]
cxgb4vf: add call to Firmware to reset VF State.

Add call to Firmware to reset its VF State when we first attach to the VF.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agocxgb4vf: Fail open if link_start() fails.
Casey Leedom [Thu, 11 Nov 2010 09:06:52 +0000]
cxgb4vf: Fail open if link_start() fails.

Fail open if link_start() fails.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agocxgb4vf: flesh out PCI Device ID Table ...
Casey Leedom [Thu, 11 Nov 2010 09:06:51 +0000]
cxgb4vf: flesh out PCI Device ID Table ...

Add a bunch of T4 Device IDs for the VF Driver.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agocxgb4vf: fix some errors in Gather List to skb conversion
Casey Leedom [Thu, 11 Nov 2010 09:06:50 +0000]
cxgb4vf: fix some errors in Gather List to skb conversion

There were some errors in the way that internal Gather Lists were being
translated into skb's.  This also makes the VF Driver look more like the PF
Driver to facilitate easier comarison.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agocxgb4vf: fix bug in Generic Receive Offload
Casey Leedom [Thu, 11 Nov 2010 09:06:49 +0000]
cxgb4vf: fix bug in Generic Receive Offload

Fix botch in Generic Receive Offload (the Packet Gather List Total length
field wasn't being initialized).

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agocxgb4vf: don't implement trivial (and incorrect) ndo_select_queue()
Casey Leedom [Thu, 11 Nov 2010 09:06:48 +0000]
cxgb4vf: don't implement trivial (and incorrect) ndo_select_queue()

Don't implement (struct net_device_ops *)->ndo_select_queue() with simple
call to skb_tx_hash().  This leads to non-persistent TX queue selection in
the Linux dev_pick_tx() routine for TCP connections.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoixgbe: Look inside vlan when determining offload protocol.
Hao Zheng [Thu, 11 Nov 2010 13:47:59 +0000]
ixgbe: Look inside vlan when determining offload protocol.

Currently the skb->protocol field is used to setup various
offloading parameters on transmit for the correct protocol.
However, if vlan offloading is disabled or otherwise not used,
the protocol field will be ETH_P_8021Q, not the actual protocol.
This will cause the offloading to be not performed correctly,
even though the hardware is capable of looking inside vlan tags.
Instead, look inside the header if necessary to determine the
correct protocol type.

To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.

Signed-off-by: Hao Zheng <hzheng@nicira.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agobnx2x: Look inside vlan when determining checksum proto.
Hao Zheng [Thu, 11 Nov 2010 13:47:58 +0000]
bnx2x: Look inside vlan when determining checksum proto.

Currently the skb->protocol field is used to setup checksum
offloading on transmit for the correct protocol.  However, if
vlan offloading is disabled or otherwise not used, the protocol
field will be ETH_P_8021Q, not the actual protocol.  This will
cause the checksum to be not computed correctly, even though the
hardware is capable of looking inside vlan tags.  Instead,
look inside the header if necessary to determine the correct
protocol type.

To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.

Signed-off-by: Hao Zheng <hzheng@nicira.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agovlan: Add function to retrieve EtherType from vlan packets.
Hao Zheng [Thu, 11 Nov 2010 13:47:57 +0000]
vlan: Add function to retrieve EtherType from vlan packets.

Depending on how a packet is vlan tagged (i.e. hardware accelerated or
not), the encapsulated protocol is stored in different locations.  This
provides a consistent method of accessing that protocol, which is needed
by drivers, security checks, etc.

Signed-off-by: Hao Zheng <hzheng@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agovirtio-net: init link state correctly
Jason Wang [Wed, 10 Nov 2010 14:45:41 +0000]
virtio-net: init link state correctly

For device that supports VIRTIO_NET_F_STATUS, there's no need to
assume the link is up and we need to call nerif_carrier_off() before
querying device status, otherwise we may get wrong operstate after
diver was loaded because the link watch event was not fired as
expected.

For device that does not support VIRITO_NET_F_STATUS, we could not get
its status through virtnet_update_status() and what we can only do is
always assuming the link is up.

Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoucc_geth: Fix deadlock
Joakim Tjernlund [Fri, 12 Nov 2010 03:55:09 +0000]
ucc_geth: Fix deadlock

This script:
 while [ 1==1 ] ; do ifconfig eth0 up; usleep 1950000 ;ifconfig eth0 down; dmesg -c ;done
causes in just a second or two:
INFO: task ifconfig:572 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
ifconfig      D 0ff65760     0   572    369 0x00000000
Call Trace:
[c6157be0] [c6008460] 0xc6008460 (unreliable)
[c6157ca0] [c0008608] __switch_to+0x4c/0x6c
[c6157cb0] [c028fecc] schedule+0x184/0x310
[c6157ce0] [c0290e54] __mutex_lock_slowpath+0xa4/0x150
[c6157d20] [c0290c48] mutex_lock+0x44/0x48
[c6157d30] [c01aba74] phy_stop+0x20/0x70
[c6157d40] [c01aef40] ucc_geth_stop+0x30/0x98
[c6157d60] [c01b18fc] ucc_geth_close+0x9c/0xdc
[c6157d80] [c01db0cc] __dev_close+0xa0/0xd0
[c6157d90] [c01deddc] __dev_change_flags+0x8c/0x148
[c6157db0] [c01def54] dev_change_flags+0x1c/0x64
[c6157dd0] [c0237ac8] devinet_ioctl+0x678/0x784
[c6157e50] [c0239a58] inet_ioctl+0xb0/0xbc
[c6157e60] [c01cafa8] sock_ioctl+0x174/0x2a0
[c6157e80] [c009a16c] vfs_ioctl+0xcc/0xe0
[c6157ea0] [c009a998] do_vfs_ioctl+0xc4/0x79c
[c6157f10] [c009b0b0] sys_ioctl+0x40/0x74
[c6157f40] [c00117c4] ret_from_syscall+0x0/0x38

The reason appears to be ucc_geth_stop meets adjust_link as the
PHY reports PHY changes. I belive adjust_link hangs somewhere,
holding the PHY lock, because ucc_geth_stop disabled the
controller HW.
Fix is to stop the PHY before disabling the controller.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoucc_geth: Do not bring the whole IF down when TX failure.
Joakim Tjernlund [Fri, 12 Nov 2010 03:55:08 +0000]
ucc_geth: Do not bring the whole IF down when TX failure.

ucc_geth_close lacks a cancel_work_sync(&ugeth->timeout_work)
to stop any outstanding processing of TX fail. However, one
can not call cancel_work_sync without fixing the timeout function
otherwise it will deadlock. This patch brings ucc_geth in line with
gianfar:

Don't bring the interface down and up, just reinit controller HW
and PHY.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet: Fix header size check for GSO case in recvmsg (af_packet)
Mariusz Kozlowski [Mon, 8 Nov 2010 11:58:45 +0000]
net: Fix header size check for GSO case in recvmsg (af_packet)

Parameter 'len' is size_t type so it will never get negative.

Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6
David S. Miller [Fri, 12 Nov 2010 19:04:26 +0000]
Merge git://git./linux/kernel/git/kaber/nf-2.6

8 years agortnetlink: Fix message size calculation for link messages
Thomas Graf [Thu, 11 Nov 2010 15:47:59 +0000]
rtnetlink: Fix message size calculation for link messages

nlmsg_total_size() calculates the length of a netlink message
including header and alignment. nla_total_size() calculates the
space an individual attribute consumes which was meant to be used
in this context.

Also, ensure to account for the attribute header for the
IFLA_INFO_XSTATS attribute as implementations of get_xstats_size()
seem to assume that we do so.

The addition of two message headers minus the missing attribute
header resulted in a calculated message size that was larger than
required. Therefore we never risked running out of skb tailroom.

Signed-off-by: Thomas Graf <tgraf@infradead.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoMerge master.kernel.org:/home/rmk/linux-2.6-arm
Linus Torvalds [Fri, 12 Nov 2010 18:30:49 +0000]
Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: GIC: don't disable software generated interrupts
  ARM: 6472/1: vexpress ct-ca9x4: only set twd_base if local timers are being used
  ARM: arch/arm/kernel/traps.c: Convert sprintf_symbol to %pS
  ARM: arch/arm/kernel/hw_breakpoint.c: Convert WARN_ON to WARN
  ARM: 6462/1: EP93xx: Document DMA M2P API
  ARM: 6470/1: atomic64: use generic implementation for OABI configurations
  ARM: 6469/1: perf-events: squash compiler warning
  ARM: 6468/1: backtrace: fix calculation of thread stack base
  ARM: Fix DMA coherent allocator alignment
  ARM: orion5x/kirkwood/mv78xx0: fix MPP configuration corner cases
  [ARM] TS-78xxx NAND resource type should be IORESOURCE_MEM
  ARM: pxa/saar: fix the building failure caused by typo
  ARM: pxa/cm-x2xx: remove duplicate call to pxa27x_init_irq
  ARM: pxa: fix the missing definition of IRQ_BOARD_END
  ARM: mmp: fix cpuid detection on mmp2
  [ARM] Kirkwood: restrict the scope of the PCIe reset workaround
  [ARM] Kirkwood: fix timer initialization for LaCie boards
  [ARM] Kirkwood: enhance TCLK detection

8 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Linus Torvalds [Fri, 12 Nov 2010 17:52:31 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: do not pass injected events back to the originating handler
  Input: pcf8574_keypad - fix error handling in pcf8574_kp_probe
  Input: acecad - fix a memory leak in usb_acecad_probe error path
  Input: atkbd - add 'terminal' parameter for IBM Terminal keyboards
  Input: i8042 - add Sony VAIOs to MUX blacklist
  kgdboc: reset input devices (keyboards) when exiting debugger
  Input: export input_reset_device() for use in KGDB
  Input: adp5588-keys - unify common header defines

8 years agoMerge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groec...
Linus Torvalds [Fri, 12 Nov 2010 17:50:54 +0000]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (gpio-fan) Fix fan_ctrl_init error path
  hwmon: (ad7414) Return proper error code for ad7414_probe()
  hwmon: (adt7470) Return proper error code for adt7470_probe()

8 years agoMerge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
Linus Torvalds [Fri, 12 Nov 2010 16:52:47 +0000]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block

* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (27 commits)
  block: remove unused copy_io_context()
  Documentation: remove anticipatory scheduler info
  block: remove REQ_HARDBARRIER
  ioprio: rcu_read_lock/unlock protect find_task_by_vpid call (V2)
  ioprio: fix RCU locking around task dereference
  block: ioctl: fix information leak to userland
  block: read i_size with i_size_read()
  cciss: fix proc warning on attempt to remove non-existant directory
  bio: take care not overflow page count when mapping/copying user data
  block: limit vec count in bio_kmalloc() and bio_alloc_map_data()
  block: take care not to overflow when calculating total iov length
  block: check for proper length of iov entries in blk_rq_map_user_iov()
  cciss: remove controllers supported by hpsa
  cciss: use usleep_range not msleep for small sleeps
  cciss: limit commands allocated on reset_devices
  cciss: Use kernel provided PCI state save and restore functions
  cciss: fix board status waiting code
  drbd: Removed checks for REQ_HARDBARRIER on incomming BIOs
  drbd: REQ_HARDBARRIER -> REQ_FUA transition for meta data accesses
  drbd: Removed the BIO_RW_BARRIER support form the receiver/epoch code
  ...

8 years agoMerge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Fri, 12 Nov 2010 16:40:23 +0000]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, pvclock: Remove leftover scale_delta() function
  x86, apic: Remove double #include
  x86: Adjust section annotations in AMD Fam10 MMCONF enabling code
  x86, UV: Update node controller MMRs
  x86: Remove unnecessary casts of void ptr returning alloc function return values
  x86: Address gcc4.6 "set but not used" warnings in apic.h
  x86, mm: Fix section mismatch in tlb.c

8 years agoMerge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Fri, 12 Nov 2010 16:39:52 +0000]
Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf, amd: Use kmalloc_node(,__GFP_ZERO) for northbridge structure allocation
  perf_events: Fix time tracking in samples
  perf trace: update usage
  perf trace: update Documentation with new perf trace variants
  perf trace: live-mode command-line cleanup
  perf trace record: handle commands correctly
  perf record: make the record options available outside perf record
  perf trace scripting: remove system-wide param from shell scripts
  perf trace scripting: fix some small memory leaks and missing error checks
  perf: Fix usages of profile_cpu in builtin-top.c to use cpu_list
  perf, ui: Eliminate stack-smashing protection compiler complaint

8 years agoMerge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied...
Linus Torvalds [Fri, 12 Nov 2010 16:11:58 +0000]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (39 commits)
  drm/ttm: Be consistent on ttm_bo_init() failures
  drm/radeon/kms: Fix retrying ttm_bo_init() after it failed once.
  drm/radeon/kms: fix thermal sensor reporting on rv6xx
  drm/radeon/kms: fix bugs in ddc and cd path router code
  drm/radeon/kms: add support for clock/data path routers
  drm: vmwgfx: fix information leak to userland
  drivers/gpu: Use vzalloc
  drm/vmwgfx: Fix oops on failing bo pin
  drm/ttm: Remove the CAP_SYS_ADMIN requirement for bo pinning
  drm/ttm: Make sure a sync object doesn't disappear while we use it
  drm/radeon/kms: don't disable shared encoders on pre-DCE3 display blocks
  drivers/gpu/drm: Update WARN uses
  drivers/gpu/drm/vmwgfx: Fix k.alloc switched arguments
  DRM: ignore invalid EDID extensions
  drm/radeon/kms: make the connector code less verbose
  drm/ttm: remove failed ttm binding error printout
  drm/ttm: Add a barrier when unreserving
  drm/ttm: Remove mm init error printouts and checks
  drm/ttm: Remove pointless list_empty check
  drm/ttm: Use private locks for the default bo range manager
  ...

8 years agoMerge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
Linus Torvalds [Fri, 12 Nov 2010 16:11:03 +0000]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: remove incorrect assert in xfs_vm_writepage
  xfs: use hlist_add_fake
  xfs: fix a few compiler warnings with CONFIG_XFS_QUOTA=n
  xfs: tell lockdep about parent iolock usage in filestreams
  xfs: move delayed write buffer trace
  xfs: fix per-ag reference counting in inode reclaim tree walking
  xfs: xfs_ioctl: fix information leak to userland
  xfs: remove experimental tag from the delaylog option

8 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris...
Linus Torvalds [Fri, 12 Nov 2010 16:00:25 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  APPARMOR: Fix memory leak of apparmor_init()
  APPARMOR: Fix memory leak of alloc_namespace()

8 years agoMerge branch 'for-2.6.37' of git://linux-nfs.org/~bfields/linux
Linus Torvalds [Fri, 12 Nov 2010 15:59:41 +0000]
Merge branch 'for-2.6.37' of git://linux-nfs.org/~bfields/linux

* 'for-2.6.37' of git://linux-nfs.org/~bfields/linux:
  locks: remove dead lease error-handling code
  locks: fix leak on merging leases
  nfsd4: fix 4.1 connection registration race

8 years agocrypto: pcrypt - Fix use after free on padata_free
Steffen Klassert [Wed, 10 Nov 2010 11:21:43 +0000]
crypto: pcrypt - Fix use after free on padata_free

kobject_put is called from padata_free for the padata kobject.
The kobject's release function frees the padata instance,
so don't call kobject_put for the padata kobject from pcrypt.

Reported-and-tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agobacklight: MacBookAir3,1(3,2) mbp-nvidia-bl support
Edgar (gimli) Hucek [Thu, 11 Nov 2010 22:05:30 +0000]
backlight: MacBookAir3,1(3,2) mbp-nvidia-bl support

Add support for the MacBookAir3,1 and MacBookAir3,2 to the mbp-nvidia-bl
driver.

Signed-off-by: Edgar (gimli) Hucek <gimli@dark-green.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agodrivers/video/backlight/adp8860_bl.c: check strict_strtoul() return value
Michael Hennerich [Thu, 11 Nov 2010 22:05:29 +0000]
drivers/video/backlight/adp8860_bl.c: check strict_strtoul() return value

Handle return value, strict_strtoul is declared with attribute
warn_unused_result.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agodrivers/video/backlight/adp8860_bl.c: fix ambient light zone overwrite handling
Michael Hennerich [Thu, 11 Nov 2010 22:05:29 +0000]
drivers/video/backlight/adp8860_bl.c: fix ambient light zone overwrite handling

This affects the get/set of the current Ambient Light Zone.  Reading
should return an integer between 1..3 (1 = Daylight, 2 = office, 3 =
dark).  Writing a value between 1..3 forces the backlight controller to
enter the corresponding Ambient Light Zone.  Writing 0 returns to normal
operation.

Fix valid range checking so we don't write invalid values to the
controller, and make sure we subtract 1, since this is what the register
definition (CFGR:BLV) requires.  Otherwise the values written don't work
correctly.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agobacklight: add low threshold to pwm backlight
Arun Murthy [Thu, 11 Nov 2010 22:05:28 +0000]
backlight: add low threshold to pwm backlight

The intensity of the backlight can be varied from a range of
max_brightness to zero.  Though most, if not all the pwm based backlight
devices start flickering at lower brightness value.  And also for each
device there exists a brightness value below which the backlight appears
to be turned off though the value is not equal to zero.

If the range of brightness for a device is from zero to max_brightness.  A
graph is plotted for brightness Vs intensity for the pwm based backlight
device has to be a linear graph.

intensity
  |   /
  |  /
  | /
  |/
  ---------
 0 max_brightness

But pratically on measuring the above we note that the intensity of
backlight goes to zero(OFF) when the value in not zero almost nearing to
zero(some x%).  so the graph looks like

intensity
  |    /
  |   /
  |  /
  |  |
  ------------
 0   x  max_brightness

In order to overcome this drawback knowing this x% i.e nothing but the low
threshold beyond which the backlight is off and will have no effect, the
brightness value is being offset by the low threshold value(retaining the
linearity of the graph).  Now the graph becomes

intensity
  |     /
  |    /
  |   /
  |  /
  -------------
   0   max_brightness

With this for each and every digit increment in the brightness from zero
there is a change in the intensity of backlight.  Devices having this
behaviour can set the low threshold brightness(lth_brightness) and pass
the same as platform data else can have it as zero.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agodrivers/video/backlight/s6e63m0.c: fix section mismatch
Axel Lin [Thu, 11 Nov 2010 22:05:27 +0000]
drivers/video/backlight/s6e63m0.c: fix section mismatch

Eliminate section mismatch warning by marking s6e63m0_probe() as __devinit.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Cc: InKi Dae <inki.dae@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agodrivers/video/backlight/s6e63m0.c: unregister backlight device and remove sysfs attri...
Axel Lin [Thu, 11 Nov 2010 22:05:26 +0000]
drivers/video/backlight/s6e63m0.c: unregister backlight device and remove sysfs attribute file in s6e63m0_remove

s6e63m0_probe() registered backlight device and create sysfs attribute
files, thus s6e63m0_remove() should unregister backlight device and remove
sysfs attribute files.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Cc: InKi Dae <inki.dae@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agobacklight: fix blanking for L4F00242T03 LCD
Marek Vasut [Thu, 11 Nov 2010 22:05:26 +0000]
backlight: fix blanking for L4F00242T03 LCD

The LCD was turned on if the variable power was > 0, but that was
incorrect.  The LCD has to be turned on in NORMAL and UNBLANK case.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agobacklight: fix blanking for LMS283GF05 LCD
Marek Vasut [Thu, 11 Nov 2010 22:05:25 +0000]
backlight: fix blanking for LMS283GF05 LCD

The LCD was turned on if the variable power was > 0, but that was
incorrect.  The LCD has to be turned on in NORMAL and UNBLANK case.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agodrivers/video/backlight/s6e63m0.c: set permissions on gamma_table file to 0444
Axel Lin [Thu, 11 Nov 2010 22:05:25 +0000]
drivers/video/backlight/s6e63m0.c: set permissions on gamma_table file to 0444

gamma_table is not writable, so set permissions to 0444.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agodrivers/leds/leds-gpio.c: properly initialize return value
Davidlohr Bueso [Thu, 11 Nov 2010 22:05:24 +0000]
drivers/leds/leds-gpio.c: properly initialize return value

In the event that none of the configs are set (CONFIG_LEDS_GPIO_PLATFORM,
CONFIG_LEDS_GPIO_OF, CONFIG_LEDS_GPIO_PLATFORM), we will return a bogus
value when initializing the module.

Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoDocumentation: led drivers lp5521 and lp5523
Samu Onkalo [Thu, 11 Nov 2010 22:05:23 +0000]
Documentation: led drivers lp5521 and lp5523

Create sub directory Documentation/leds and add short documentation for
LP5521 and LP5523 drivers.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoleds: update LP552x support Kconfig and Makefile
Samu Onkalo [Thu, 11 Nov 2010 22:05:23 +0000]
leds: update LP552x support Kconfig and Makefile

Provide configuration and compilation support for LP5521 and LP5523

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoleds: driver for National Semiconductors LP5523 chip
Samu Onkalo [Thu, 11 Nov 2010 22:05:22 +0000]
leds: driver for National Semiconductors LP5523 chip

LP5523 chip is nine channel led driver with programmable engines.  Driver
provides support for that chip for direct access via led class or via
programmable engines.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoleds: driver for National Semiconductor LP5521 chip
Samu Onkalo [Thu, 11 Nov 2010 22:05:22 +0000]
leds: driver for National Semiconductor LP5521 chip

This patchset provides support for LP5521 and LP5523 LED driver chips from
National Semicondutor.  Both drivers supports programmable engines and
naturally LED class features.

Documentation is provided as a part of the patchset.  I created "leds"
subdirectory under Documentation.  Perhaps the rest of the leds*
documentation should be moved there.

Datasheets are freely available at National Semiconductor www pages.

This patch:

LP5521 chip is three channel led driver with programmable engines.  Driver
provides support for that chip for direct access via led class or via
programmable engines.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoled-class: always implement blinking
Johannes Berg [Thu, 11 Nov 2010 22:05:21 +0000]
led-class: always implement blinking

Currently, blinking LEDs can be awkward because it is not guaranteed that
all LEDs implement blinking.  The trigger that wants it to blink then
needs to implement its own timer solution.

Rather than require that, add led_blink_set() API that triggers can use.
This function will attempt to use hw blinking, but if that fails
implements a timer for it.  To stop blinking again, brightness_set() also
needs to be wrapped into API that will stop the software blink.

As a result of this, the timer trigger becomes a very trivial one, and
hopefully we can finally see triggers using blinking as well because it's
always easy to use.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agohugetlbfs: lessen the impact of a deprecation warning
Dave Jones [Thu, 11 Nov 2010 22:05:20 +0000]
hugetlbfs: lessen the impact of a deprecation warning

WARN_ONCE is a bit strong for a deprecation warning, given that it spews a
huge backtrace.

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoradix-tree: fix RCU bug
Nick Piggin [Thu, 11 Nov 2010 22:05:19 +0000]
radix-tree: fix RCU bug

Salman Qazi describes the following radix-tree bug:

In the following case, we get can get a deadlock:

0.  The radix tree contains two items, one has the index 0.
1.  The reader (in this case find_get_pages) takes the rcu_read_lock.
2.  The reader acquires slot(s) for item(s) including the index 0 item.
3.  The non-zero index item is deleted, and as a consequence the other item is
    moved to the root of the tree. The place where it used to be is queued for
    deletion after the readers finish.
3b. The zero item is deleted, removing it from the direct slot, it remains in
    the rcu-delayed indirect node.
4.  The reader looks at the index 0 slot, and finds that the page has 0 ref
    count
5.  The reader looks at it again, hoping that the item will either be freed or
    the ref count will increase. This never happens, as the slot it is looking
    at will never be updated. Also, this slot can never be reclaimed because
    the reader is holding rcu_read_lock and is in an infinite loop.

The fix is to re-use the same "indirect" pointer case that requires a slot
lookup retry into a general "retry the lookup" bit.

Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Reported-by: Salman Qazi <sqazi@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoRestrict unprivileged access to kernel syslog
Dan Rosenberg [Thu, 11 Nov 2010 22:05:18 +0000]
Restrict unprivileged access to kernel syslog

The kernel syslog contains debugging information that is often useful
during exploitation of other vulnerabilities, such as kernel heap
addresses.  Rather than futilely attempt to sanitize hundreds (or
thousands) of printk statements and simultaneously cripple useful
debugging functionality, it is far simpler to create an option that
prevents unprivileged users from reading the syslog.

This patch, loosely based on grsecurity's GRKERNSEC_DMESG, creates the
dmesg_restrict sysctl.  When set to "0", the default, no restrictions are
enforced.  When set to "1", only users with CAP_SYS_ADMIN can read the
kernel syslog via dmesg(8) or other mechanisms.

[akpm@linux-foundation.org: explain the config option in kernel.txt]
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Eugene Teo <eugeneteo@kernel.org>
Acked-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agooom: document obsolete oom_adj tunable
David Rientjes [Thu, 11 Nov 2010 22:05:18 +0000]
oom: document obsolete oom_adj tunable

/proc/pid/oom_adj was deprecated in August 2010 with the introduction of
the new oom killer heuristic.

This patch copies the Documentation/feature-removal-schedule.txt entry for
this tunable to the Documentation/ABI/obsolete directory so nobody misses
it.

Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agovmscan: avoid setting zone congested if no page dirty
Shaohua Li [Thu, 11 Nov 2010 22:05:17 +0000]
vmscan: avoid setting zone congested if no page dirty

nr_dirty and nr_congested are increased only when the page is dirty.  So
if all pages are clean, both them will be zero.  In this case, we should
not mark the zone congested.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agolatencytop: fix per task accumulator
Ken Chen [Thu, 11 Nov 2010 22:05:16 +0000]
latencytop: fix per task accumulator

Per task latencytop accumulator prematurely terminates due to erroneous
placement of latency_record_count.  It should be incremented whenever a
new record is allocated instead of increment on every latencytop event.

Also fix search iterator to only search known record events instead of
blindly searching all pre-allocated space.

Signed-off-by: Ken Chen <kenchen@google.com>
Reviewed-by: Arjan van de Ven <arjan@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agomm/vfs: revalidate page->mapping in do_generic_file_read()
Dave Hansen [Thu, 11 Nov 2010 22:05:15 +0000]
mm/vfs: revalidate page->mapping in do_generic_file_read()

70 hours into some stress tests of a 2.6.32-based enterprise kernel, we
ran into a NULL dereference in here:

int block_is_partially_uptodate(struct page *page, read_descriptor_t *desc,
                                        unsigned long from)
{
----> struct inode *inode = page->mapping->host;

It looks like page->mapping was the culprit.  (xmon trace is below).
After closer examination, I realized that do_generic_file_read() does a
find_get_page(), and eventually locks the page before calling
block_is_partially_uptodate().  However, it doesn't revalidate the
page->mapping after the page is locked.  So, there's a small window
between the find_get_page() and ->is_partially_uptodate() where the page
could get truncated and page->mapping cleared.

We _have_ a reference, so it can't get reclaimed, but it certainly
can be truncated.

I think the correct thing is to check page->mapping after the
trylock_page(), and jump out if it got truncated.  This patch has been
running in the test environment for a month or so now, and we have not
seen this bug pop up again.

xmon info:

  1f:mon> e
  cpu 0x1f: Vector: 300 (Data Access) at [c0000002ae36f770]
      pc: c0000000001e7a6c: .block_is_partially_uptodate+0xc/0x100
      lr: c000000000142944: .generic_file_aio_read+0x1e4/0x770
      sp: c0000002ae36f9f0
     msr: 8000000000009032
     dar: 0
   dsisr: 40000000
    current = 0xc000000378f99e30
    paca    = 0xc000000000f66300
      pid   = 21946, comm = bash
  1f:mon> r
  R00 = 0025c0500000006d   R16 = 0000000000000000
  R01 = c0000002ae36f9f0   R17 = c000000362cd3af0
  R02 = c000000000e8cd80   R18 = ffffffffffffffff
  R03 = c0000000031d0f88   R19 = 0000000000000001
  R04 = c0000002ae36fa68   R20 = c0000003bb97b8a0
  R05 = 0000000000000000   R21 = c0000002ae36fa68
  R06 = 0000000000000000   R22 = 0000000000000000
  R07 = 0000000000000001   R23 = c0000002ae36fbb0
  R08 = 0000000000000002   R24 = 0000000000000000
  R09 = 0000000000000000   R25 = c000000362cd3a80
  R10 = 0000000000000000   R26 = 0000000000000002
  R11 = c0000000001e7b60   R27 = 0000000000000000
  R12 = 0000000042000484   R28 = 0000000000000001
  R13 = c000000000f66300   R29 = c0000003bb97b9b8
  R14 = 0000000000000001   R30 = c000000000e28a08
  R15 = 000000000000ffff   R31 = c0000000031d0f88
  pc  = c0000000001e7a6c .block_is_partially_uptodate+0xc/0x100
  lr  = c000000000142944 .generic_file_aio_read+0x1e4/0x770
  msr = 8000000000009032   cr  = 22000488
  ctr = c0000000001e7a60   xer = 0000000020000000   trap =  300
  dar = 0000000000000000   dsisr = 40000000
  1f:mon> t
  [link register   ] c000000000142944 .generic_file_aio_read+0x1e4/0x770
  [c0000002ae36f9f0] c000000000142a14 .generic_file_aio_read+0x2b4/0x770 (unreliable)
  [c0000002ae36fb40] c0000000001b03e4 .do_sync_read+0xd4/0x160
  [c0000002ae36fce0] c0000000001b153c .vfs_read+0xec/0x1f0
  [c0000002ae36fd80] c0000000001b1768 .SyS_read+0x58/0xb0
  [c0000002ae36fe30] c00000000000852c syscall_exit+0x0/0x40
  --- Exception: c00 (System Call) at 00000080a840bc54
  SP (fffca15df30) is in userspace
  1f:mon> di c0000000001e7a6c
  c0000000001e7a6c  e9290000      ld      r9,0(r9)
  c0000000001e7a70  418200c0      beq     c0000000001e7b30        # .block_is_partially_uptodate+0xd0/0x100
  c0000000001e7a74  e9440008      ld      r10,8(r4)
  c0000000001e7a78  78a80020      clrldi  r8,r5,32
  c0000000001e7a7c  3c000001      lis     r0,1
  c0000000001e7a80  812900a8      lwz     r9,168(r9)
  c0000000001e7a84  39600001      li      r11,1
  c0000000001e7a88  7c080050      subf    r0,r8,r0
  c0000000001e7a8c  7f805040      cmplw   cr7,r0,r10
  c0000000001e7a90  7d6b4830      slw     r11,r11,r9
  c0000000001e7a94  796b0020      clrldi  r11,r11,32
  c0000000001e7a98  419d00a8      bgt     cr7,c0000000001e7b40    # .block_is_partially_uptodate+0xe0/0x100
  c0000000001e7a9c  7fa55840      cmpld   cr7,r5,r11
  c0000000001e7aa0  7d004214      add     r8,r0,r8
  c0000000001e7aa4  79080020      clrldi  r8,r8,32
  c0000000001e7aa8  419c0078      blt     cr7,c0000000001e7b20    # .block_is_partially_uptodate+0xc0/0x100

Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: <arunabal@in.ibm.com>
Cc: <sbest@us.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agokernel/range.c: fix clean_sort_range() for the case of full array
Alexey Khoroshilov [Thu, 11 Nov 2010 22:05:14 +0000]
kernel/range.c: fix clean_sort_range() for the case of full array

clean_sort_range() should return a number of nonempty elements of range
array, but if the array is full clean_sort_range() returns 0.

The problem is that the number of nonempty elements is evaluated by
finding the first empty element of the array.  If there is no such element
it returns an initial value of local variable nr_range that is zero.

The fix is trivial: it changes initial value of nr_range to size of the
array.

The bug can lead to loss of information regarding all ranges, since
typically returned value of clean_sort_range() is considered as an actual
number of ranges in the array after a series of add/subtract operations.

Found by Analytical Verification project of Linux Verification Center
(linuxtesting.org), thanks to Alexander Kolosov.

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agodrivers/misc/bh1770glc.c: error handling in bh1770_power_state_store()
Dan Carpenter [Thu, 11 Nov 2010 22:05:13 +0000]
drivers/misc/bh1770glc.c: error handling in bh1770_power_state_store()

There was a signedness bug so "ret" was never less than zero and that
breaks the error handling.  Also in the original code it would overwrite
ret and the result is still negative but it's bogus number instead of the
correct error code.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agomemcg: null dereference on allocation failure
Dan Carpenter [Thu, 11 Nov 2010 22:05:12 +0000]
memcg: null dereference on allocation failure

The original code had a null dereference if alloc_percpu() failed.  This
was introduced in commit 711d3d2c9bc3 ("memcg: cpu hotplug aware percpu
count updates")

Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agodrivers/misc/apds9802als.c: fix signedness bug
Vasiliy Kulikov [Thu, 11 Nov 2010 22:05:11 +0000]
drivers/misc/apds9802als.c: fix signedness bug

i2c_smbus_read_byte_data() may return negative error code.  This is not
seen to als_sensing_range_store() as the result is stored in unsigned int.

Made it signed.

Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: Hong Liu <hong.liu@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Anantha Narayanan <anantha.narayanan@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agomisc/isl29020: signedness bug in als_sensing_range_store()
Dan Carpenter [Thu, 11 Nov 2010 22:05:11 +0000]
misc/isl29020: signedness bug in als_sensing_range_store()

"ret_val" is supposed to be signed here or the error handling breaks.
Also we should check the return value from i2c_smbus_read_byte_data().

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoinclude/linux/highmem.h needs hardirq.h
Catalin Marinas [Thu, 11 Nov 2010 22:05:10 +0000]
include/linux/highmem.h needs hardirq.h

Commit 3e4d3af501cc ("mm: stack based kmap_atomic()") introduced the
kmap_atomic_idx_push() function which warns on in_irq() with
CONFIG_DEBUG_HIGHMEM enabled.  This patch includes linux/hardirq.h for
the in_irq definition.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoatomic: add atomic_inc_not_zero_hint()
Eric Dumazet [Thu, 11 Nov 2010 22:05:08 +0000]
atomic: add atomic_inc_not_zero_hint()

Followup of perf tools session in Netfilter WorkShop 2010

In the network stack we make high usage of atomic_inc_not_zero() in
contexts we know the probable value of atomic before increment (2 for udp
sockets for example)

Using a special version of atomic_inc_not_zero() giving this hint can help
processor to use less bus transactions.

On x86 (MESI protocol) for example, this avoids entering Shared state,
because "lock cmpxchg" issues an RFO (Read For Ownership)

akpm: Adds a new include/linux/atomic.h.  This means that new code should
henceforth include linux/atomic.h and not asm/atomic.h.  The presence of
include/linux/atomic.h will in fact cause checkpatch.pl to warn about use
of asm/atomic.h.  The new include/linux/atomic.h becomes the place where
arch-neutral atomic_t code should be placed.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: David Miller <davem@davemloft.net>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Reviewed-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoinclude/linux/resource.h needs types.h
Jean Delvare [Thu, 11 Nov 2010 22:05:07 +0000]
include/linux/resource.h needs types.h

Fix the following warning:
usr/include/linux/resource.h:49: found __[us]{8,16,32,64} type without #include <linux/types.h>

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agorapidio: use resource_size()
Dan Carpenter [Thu, 11 Nov 2010 22:05:07 +0000]
rapidio: use resource_size()

The size calculation is done incorrectly here because it should include
both the start and end (end - start + 1).  It's easiest to just use
resource_size() which does the right thing.

I was worried there was something non-standard going on because the
printk() subtracts "end - 1", but the rest of the file uses the normal
resource size calculations.  This function is only called from
fsl_rio_setup() in arch/powerpc/sysdev/fsl_rio.c and the calculation
there is also:

port->iores.start = law_start;
port->iores.end = law_start + law_size - 1;

So I think this is the correct fix.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agodrivers/macintosh/adb-iop.c: flags should be unsigned long
Geert Uytterhoeven [Thu, 11 Nov 2010 22:05:06 +0000]
drivers/macintosh/adb-iop.c: flags should be unsigned long

Fix these warnings:

  drivers/macintosh/adb-iop.c: In function `adb_iop_complete':
  drivers/macintosh/adb-iop.c:85: warning: comparison of distinct pointer types lacks a cast
  drivers/macintosh/adb-iop.c:92: warning: comparison of distinct pointer types lacks a cast
  drivers/macintosh/adb-iop.c: In function ¡adb_iop_listen¢:
  drivers/macintosh/adb-iop.c:111: warning: comparison of distinct pointer types lacks a cast
  drivers/macintosh/adb-iop.c:151: warning: comparison of distinct pointer types lacks a cast

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoum: fix ptrace build error
Richard Weinberger [Thu, 11 Nov 2010 22:05:04 +0000]
um: fix ptrace build error

Both commits 0a3d763f1a68 ("ptrace: cleanup arch_ptrace() on um") and
9b05a69e0534 ("ptrace: change signature of arch_ptrace()") broke the um
build.  This patch fixes the issues.

0a3d763f1a68 introduced the undeclared variable "datavp".  The patch seems
completely untested.  :-(

9b05a69e0534 changed arch_ptrace()'s signature but did not update
um/include/asm/ptrace-generic.h.

Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Tested-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoARM: GIC: don't disable software generated interrupts
Russell King [Thu, 11 Nov 2010 23:10:30 +0000]
ARM: GIC: don't disable software generated interrupts

Software generated interrupts (SGI) are used for IPIs by the kernel.
While previous revisions of the GIC hardware were specified not to
implement enable bits for SGIs, more recent hardware is now permitted
to implement these bits in a per-CPU banked register.

The priority registers for the PPI and SGIs are also per-CPU banked
registers, so ensure that these are also appropriately initialized.

Reported-by: Scott Valentine <svalentine@concentris-systems.com>
Acked-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

8 years agonetfilter: ipv6: fix overlap check for fragments
Shan Wei [Fri, 12 Nov 2010 07:51:55 +0000]
netfilter: ipv6: fix overlap check for fragments

The type of FRAG6_CB(prev)->offset is int, skb->len is *unsigned* int,
and offset is int.

Without this patch, type conversion occurred to this expression, when
(FRAG6_CB(prev)->offset + prev->len) is less than offset.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>

8 years agonetfilter: NF_HOOK_COND has wrong conditional
Eric Paris [Fri, 12 Nov 2010 07:26:06 +0000]
netfilter: NF_HOOK_COND has wrong conditional

The NF_HOOK_COND returns 0 when it shouldn't due to what I believe to be an
error in the code as the order of operations is not what was intended.  C will
evalutate == before =.  Which means ret is getting set to the bool result,
rather than the return value of the function call.  The code says

if (ret = function() == 1)
when it meant to say:
if ((ret = function()) == 1)

Normally the compiler would warn, but it doesn't notice it because its
a actually complex conditional and so the wrong code is wrapped in an explict
set of () [exactly what the compiler wants you to do if this was intentional].
Fixing this means that errors when netfilter denies a packet get propagated
back up the stack rather than lost.

Problem introduced by commit 2249065f (netfilter: get rid of the grossness
in netfilter.h).

Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>

8 years agon_gsm: Fix length handling
Ken Mills [Thu, 4 Nov 2010 15:16:42 +0000]
n_gsm: Fix length handling

If the mux is configured with a large mru/mtu the existing code gets the
byte ordering wrong for the header.

Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

8 years agon_gsm: Copy n2 over when configuring via ioctl interface
Ken Mills [Thu, 4 Nov 2010 15:16:24 +0000]
n_gsm: Copy n2 over when configuring via ioctl interface

The n2 field is settable but didn't get propogated

Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

8 years agoserial: bfin_5xx: grab port lock before making port termios changes
Sonic Zhang [Wed, 27 Oct 2010 08:16:50 +0000]
serial: bfin_5xx: grab port lock before making port termios changes

The port lock exists to protect these resources, so we need to grab it
before making changes.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

8 years agoserial: bfin_5xx: disable CON_PRINTBUFFER for consoles
Sonic Zhang [Wed, 27 Oct 2010 08:16:49 +0000]
serial: bfin_5xx: disable CON_PRINTBUFFER for consoles

If we are using early serial, don't let the normal console rewind
the log buffer, since that causes things to be printed multiple times.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

8 years agoserial: bfin_5xx: remove redundant SSYNC to improve TX speed
Sonic Zhang [Wed, 27 Oct 2010 08:16:48 +0000]
serial: bfin_5xx: remove redundant SSYNC to improve TX speed

We don't need to force a SSYNC here as the LSR register will already
be updated by the time we get back to reading it.  This speeds up TX
throughput and lowers general system overhead (since SSYNC is system
wide, not peripheral-specific).

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

8 years agoserial: bfin_5xx: always include DMA headers
Sonic Zhang [Wed, 27 Oct 2010 08:16:47 +0000]
serial: bfin_5xx: always include DMA headers

On Blackfin systems, peripherals that have optional DMA support always
route their interrupts through the corresponding DMA channel -- even
when DMA is not being used.  So in PIO mode, we still need to request
the DMA channel (so interrupts are delivered) which means we need to
always include the DMA header for the DMA defines/functions.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>