9 years agomtd-physmap: add support users can assign the probe type in board files
Barry Song [Fri, 15 Jan 2010 07:50:14 +0000]
mtd-physmap: add support users can assign the probe type in board files

There are three reasons to add this support:
1. users probably know the interface type of their flashs, then probe
can be faster if they give the right type in platform data since wrong
types will not be detected.
2. sometimes, detecting can cause destory to system. For example, for
kernel XIP, detecting can cause NOR enter a mode instructions can not
be fetched right, which will make kernel crash.
3. For a new probe which is not listed in the rom_probe_types, if users
assign it in board files, physmap can still probe it.

Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: remove redwood map driver
Christian Dietrich [Fri, 16 Jul 2010 12:29:08 +0000]
mtd: remove redwood map driver

Removing the redwood mtd mapping driver, because all REDWOOD_[456]
configuration options were removed from the kernel, because they weren't
referenced anywhere.

Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomxc_nand: Add v3 (i.MX51) Support
Sascha Hauer [Fri, 6 Aug 2010 13:53:11 +0000]
mxc_nand: Add v3 (i.MX51) Support

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomxc_nand: support 8bit ecc
Sascha Hauer [Fri, 6 Aug 2010 13:53:10 +0000]
mxc_nand: support 8bit ecc

Nand devices with at least 26 bytes of oob data per 512 byte block
can have 8bit ecc on v2 type controllers. This is currently not tested,
but at least this patch puts the ECC_MODE bit into a well defined state.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomxc_nand: fix correct_data function
Sascha Hauer [Fri, 6 Aug 2010 13:53:09 +0000]
mxc_nand: fix correct_data function

The v2 controller has a totally different mechanism to check
whether the data we read had ecc errors or not. Implement this.
The mechanism in the v2 controller happens to be identical to
the v3 controller.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomxc_nand: add V1_V2 namespace to registers
Sascha Hauer [Fri, 6 Aug 2010 13:53:08 +0000]
mxc_nand: add V1_V2 namespace to registers

This prepares the driver for v3 support. The v3 controller
has a completely different register layout, so add a V1_V2_
namespace to the register defines to avoid confusion with
the v3 regs.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomxc_nand: factor out a check_int function
Sascha Hauer [Fri, 6 Aug 2010 13:53:07 +0000]
mxc_nand: factor out a check_int function

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomxc_nand: make some internally used functions overwriteable
Sascha Hauer [Fri, 6 Aug 2010 13:53:06 +0000]
mxc_nand: make some internally used functions overwriteable

This patch prepares the driver to add v3 controller support
later. The v3 controller is basically the same controller as v1
and v2, but with a completely different register layout.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomxc_nand: rework get_dev_status
Sascha Hauer [Fri, 6 Aug 2010 13:53:05 +0000]
mxc_nand: rework get_dev_status

We save/restore the value in the buffer anyway, so it makes
no difference whether we use main_area0 or main_area1. So,
we can use main_area0 and remove main_area1 from the driver
which is otherwise unused. Also, clean up the comments in
get_dev_status.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomxc_nand: remove 0xe00 offset from registers
Sascha Hauer [Fri, 6 Aug 2010 13:53:04 +0000]
mxc_nand: remove 0xe00 offset from registers

Add the offset to the register base instead. This is done
in preparation for v3 controller support.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali: Add multi connected NAND support
Chuanxiao Dong [Fri, 6 Aug 2010 10:19:09 +0000]
mtd: denali: Add multi connected NAND support

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali: Remove set_ecc_config function
Chuanxiao Dong [Fri, 6 Aug 2010 10:02:03 +0000]
mtd: denali: Remove set_ecc_config function

set_ecc_config function only set ECC_CORRECTION register, so
move register setting to probe function.
Since controller only support 15bit and 8bit ecc correction,
updated nand ecc layout information.

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali: Remove unuseful code in get_xx_nand_para functions
Chuanxiao Dong [Fri, 6 Aug 2010 07:45:19 +0000]
mtd: denali: Remove unuseful code in get_xx_nand_para functions

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali: Remove device_info_tag structure
Chuanxiao.Dong [Fri, 6 Aug 2010 10:48:21 +0000]
mtd: denali: Remove device_info_tag structure

Hi David,
   I sent 4 patches using my intel email account. If there is any
   problem about the format of these patches, I will resend them after
   I arrived at home by using my gmail account, and I will keep on
   using gmail account to send patches.
   Thanks.

>From 242e3bf5e17f54b1df8cf285154a7c7a61ff62e9 Mon Sep 17 00:00:00 2001
From: Chuanxiao Dong <chuanxiao.dong@intel.com>
Date: Fri, 6 Aug 2010 15:29:41 +0800
Subject: [PATCH 1/4] mtd: denali: Remove device_info_tag structure.

Most of the variables in this structure are useless, so just
remove this structure and relevant codes.

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: m25p80: add support for the Winbond W25Q32 SPI flash chip
Gabor Juhos [Wed, 4 Aug 2010 19:14:27 +0000]
mtd: m25p80: add support for the Winbond W25Q32 SPI flash chip

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>

9 years agomtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips
Gabor Juhos [Thu, 5 Aug 2010 14:58:36 +0000]
mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: m25p80: add support for the EON EN25P{32, 64} SPI flash chips
Gabor Juhos [Wed, 4 Aug 2010 19:14:25 +0000]
mtd: m25p80: add support for the EON EN25P{32, 64} SPI flash chips

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: cfi_cmdset_0002: consider version 1.4 as a valid primary extension version
Guillaume LECERF [Thu, 5 Aug 2010 11:55:24 +0000]
mtd: cfi_cmdset_0002: consider version 1.4 as a valid primary extension version

The Spansion S29WS-P device family uses CFI version 1.4 [1].
Consider it as a valid version.

[1] http://www.spansion.com/Support/Datasheets/s29ws-p_00_a12_e.pdf

Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: atmel_nand: fix warning: 'part_probes' defined but not used
Andreas Bießmann [Thu, 5 Aug 2010 10:38:41 +0000]
mtd: atmel_nand: fix warning: 'part_probes' defined but not used

This patch fixes

drivers/mtd/nand/atmel_nand.c:372: warning: 'part_probes' defined but not used

which is issued when CONFIG_MTD_PARTITIONS is defined but
CONFIG_MTD_CMDLINE_PARTS not.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: change struct flchip_shared spinlock locking into mutex
Stefani Seibold [Thu, 5 Aug 2010 07:19:26 +0000]
mtd: change struct flchip_shared spinlock locking into mutex

This patch prevent to schedule while atomic by changing the
flchip_shared spinlock into a mutex. This should be save since no atomic
path will use this lock.

It was suggested by Arnd Bergmann and Vasiliy Kulikov.

Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: Missing slab.h include
David Miller [Thu, 5 Aug 2010 05:57:51 +0000]
mtd: Missing slab.h include

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: gen_nand: fix support for multiple chips
Marek Vasut [Wed, 28 Jul 2010 05:36:54 +0000]
mtd: gen_nand: fix support for multiple chips

This patch corrects a problem where gen_nand driver assumed there can be only
one chip and ignored the pdata->chip.nr_chips value.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: update description on sm_ftl
Maxim Levitsky [Wed, 28 Jul 2010 15:53:17 +0000]
mtd: update description on sm_ftl

I think that scary description can go now...

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: blkdevs: fix crash related to sysfs attributes.
Maxim Levitsky [Wed, 28 Jul 2010 15:53:16 +0000]
mtd: blkdevs: fix crash related to sysfs attributes.

Remove the attributes group before disk to avoid use after free

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali: update get nand para functions
Chuanxiao Dong [Thu, 5 Aug 2010 16:48:49 +0000]
mtd: denali: update get nand para functions

In denali driver, wTotalBlocks variable is useless, so just
remove them in get_toshiba_nand_para and get_hynix_nand_para
first. Other wTotalBlocks in denali.c and other variables in
dev_info struct are also useless, will remove them later.

Also add a parameter in get_hynix_nand_para to prepare to
remove dev_info struct. This parameter comes by reading NAND
ID directly. Reading register will report wrong value for
some NAND chips, e.g. some Micron MT29F32G08QAA chips.
So update NAND_CMD_READID method as well.

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali: rename functions which is named by using capitals
Chuanxiao Dong [Tue, 27 Jul 2010 06:17:37 +0000]
mtd: denali: rename functions which is named by using capitals

rename these functions' name and remove additional declarations
in header file

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali.c: fix reserved all check-patch errors
Chuanxiao Dong [Tue, 27 Jul 2010 03:32:21 +0000]
mtd: denali.c: fix reserved all check-patch errors

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali.c: fix all "line over 80 characters" warnings
Chuanxiao Dong [Tue, 27 Jul 2010 03:28:09 +0000]
mtd: denali.c: fix all "line over 80 characters" warnings

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali.c: add and update KERN_ facility level in printk()
Chuanxiao Dong [Tue, 27 Jul 2010 02:48:34 +0000]
mtd: denali.c: add and update KERN_ facility level in printk()

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali.c: fixed all open brace { check-patch errors
Chuanxiao Dong [Tue, 27 Jul 2010 02:41:53 +0000]
mtd: denali.c: fixed all open brace { check-patch errors

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agonand/denali Clean up all white spaces in code indent
Chuanxiao [Thu, 5 Aug 2010 15:06:04 +0000]
nand/denali Clean up all white spaces in code indent

Hi,
I have changed the outlook mail cliet to be linux mutt client and use my
personal gmail to submit patches.
Here are 5 new patches to fix nand/denali check patch errors. The other
4 patches will be sent out after this mail.
Thanks for your review.

>From d125ad3f57bbf517131dccad6b5933edf8c2632a Mon Sep 17 00:00:00 2001
From: Chuanxiao Dong <chuanxiao.dong@intel.com>
Date: Tue, 3 Aug 2010 15:54:48 +0800
Subject: [PATCH 1/5] mtd: denali.c: clean up all whitespaces in code indent

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: Blackfin NFC: fix nand busy detection
Barry Song [Thu, 5 Aug 2010 15:07:38 +0000]
mtd: Blackfin NFC: fix nand busy detection

The IRQSTAT register is a W1C register used by the interrupt handler and
may have its BUSY bit changed.  This makes it somewhat unreliable for the
polling devready function.  So switch it over to use the BUSY bit in the
STAT register that always reflects the current state of the hardware.

This fixes driver hangs seen when the NAND flash is under heavy system
load (like I/O benchmarks).

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: Blackfin NFC: fix handling of page sizes
Barry Song [Thu, 5 Aug 2010 15:07:43 +0000]
mtd: Blackfin NFC: fix handling of page sizes

Rather than forcing the platform resources to declare the desired page
size, simply use the existing information passed down to us by the higher
layers.  This way we work out of the box with all flash chips that the
kernel knows about.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: Blackfin NFC: wait for the ECC reset to finish
Barry Song [Thu, 5 Aug 2010 15:07:41 +0000]
mtd: Blackfin NFC: wait for the ECC reset to finish

When resetting the ECC registers/counters, the bit will automatically
clear itself once the reset has actually finished.  So make sure we
wait for that to occur before doing anything else rather than assuming
everything is peachy and proceeding with stale ECC values.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: Blackfin NFC: fix typo for read/write delay setup
Barry Song [Thu, 5 Aug 2010 15:07:40 +0000]
mtd: Blackfin NFC: fix typo for read/write delay setup

We used the platform rd_dly field when we meant to use the wr_dly field.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: Blackfin NFC: make sure to check NAND_ALE in cmd_ctrl
Barry Song [Thu, 5 Aug 2010 15:07:42 +0000]
mtd: Blackfin NFC: make sure to check NAND_ALE in cmd_ctrl

The NAND base may send some controls which are neither CLE nor ALE, so
we need to explicitly check both instead of assuming things are always
one or the other.  Otherwise, we sometimes send out illegal addresses
to the NAND device.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: Blackfin NFC: fix raw page write/read handling
Barry Song [Thu, 5 Aug 2010 15:07:44 +0000]
mtd: Blackfin NFC: fix raw page write/read handling

Our write_buf/read_buf funcs always do ECC in HW ECC mode.  That is not
needed for raw funcs.  In fact, write_buf/read_buf should be a pure func
for data input/output while chip->ecc.hwctl controls ECC.  Unfortunately,
we can't separate ECC from normal data input/output in our NFC, so our DMA
write_buf/read_buf entries are coupled with ECC operations closely.

Thus we need to provide dedicated read_page_raw/write_page_raw funcs where
we do non-DMA transactions so as to avoid automatic ECC.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: Blackfin NFC: delete useless comment about jffs2
Barry Song [Thu, 5 Aug 2010 15:07:39 +0000]
mtd: Blackfin NFC: delete useless comment about jffs2

The low level NAND driver doesn't care about filesystems, so punt the
local comment indicating otherwise.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: cfi_cmdset_0002: fix the check for valid primary extension versions
Guillaume LECERF [Fri, 2 Jul 2010 12:39:10 +0000]
mtd: cfi_cmdset_0002: fix the check for valid primary extension versions

Valid primary extension versions are: 1.0, 1.1, 1.2, 1.3 [1][2].
Fix the check in cfi_cmdset_0002 accordingly.

[1] http://www.amd.com/us-en/assets/content_type/DownloadableAssets/cfi_r20.pdf, page 19
[2] http://www.amd.com/us-en/assets/content_type/DownloadableAssets/cfi_100_20011201.pdf

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: m25p80: Make jedec_probe() return proper errno values
Anton Vorontsov [Tue, 22 Jun 2010 16:57:42 +0000]
mtd: m25p80: Make jedec_probe() return proper errno values

spi_write_then_read() may return its own return codes (e.g. -EIO),
so let's propagate the value down to the probe().

Also, remove jedec == 0 check, it isn't needed as nowadays we use
dedicated SPI device IDs for non-JEDEC flashes.

Suggested-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: m25p80: Fix false-positive probing
Anton Vorontsov [Tue, 22 Jun 2010 16:57:34 +0000]
mtd: m25p80: Fix false-positive probing

Since commit 18c6182bae0acca220ed6611f741034d563cd19f ("Rework
probing/JEDEC code"), m25p80 driver successfully registers chips
even if JEDEC probing fails.

This was needed to support non-JEDEC flashes. Though, it appears
that some platforms (e.g. blackfin bf533 stamp[1]) used the old
behavior to detect if there's any flash connected, so the driver
have to fail on JEDEC probing errors.

This patch restores the old behavior for JEDEC flashes, and adds
"-nonjedec" SPI device IDs for M25Pxx flashes, so that the kernel
still supports non-JEDEC flashes.

[1] http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=5975

Reported-by: Mingquan Pan
Reported-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: mtdchar: fix mmap for MTD RAM/ROM char devices
Anatolij Gustschin [Tue, 15 Jun 2010 07:30:15 +0000]
mtd: mtdchar: fix mmap for MTD RAM/ROM char devices

For no-mmu systems mmap() on RAM/ROM devices already works
but for systems with mmu it probably was not tested and
doesn't work.

This patch allows using mmap() on MTD RAM/ROM devices on systems
with MMU. It has been tested on mpc5121e based platform with
MR0A16A MRAM device attached over LocalBus.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: ixp4xx: add support for static flash partitions
Richard Cochran [Mon, 14 Jun 2010 16:15:19 +0000]
mtd: ixp4xx: add support for static flash partitions

This patch adds support for static flash partitioning from a platform
device. Also, we clean up some weirdness where statements were separated
by commas instead of semicolons. While we are at it, fix some minor bad
white space, too.

Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: mxc_nand: dont call suspend and resume explicitly
Eric Bénard [Thu, 17 Jun 2010 18:59:04 +0000]
mtd: mxc_nand: dont call suspend and resume explicitly

The mtd layer is responsible to call mtd->{suspend,resume}.  Doing it
again in the driver is wrong and results in a warning:

nand_resume called for a chip which is not in suspended state

at resume time.  Removing the calls from the resume and suspend
functions makes them empty allowing them to be deleted completely.

Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: doc2000: fix uninitialized variable in doc_ecc_decode()
Mark Ware [Thu, 27 May 2010 01:45:39 +0000]
mtd: doc2000: fix uninitialized variable in doc_ecc_decode()

The variable 'syn' was being used uninitialized.  Also
fixed incorrect use of syn[] vs s[].

Tested on powerpc board with 64MiB DOC2000.

Signed-off-by: Mark Ware <mware@elphinstone.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: OneNAND: Samsung SoCs use own chip_probe function
Kyungmin Park [Fri, 28 May 2010 02:15:35 +0000]
mtd: OneNAND: Samsung SoCs use own chip_probe function

Samsung SoCs use own chip_probe function.
Don't touch the memory configuration at probe time.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: OneNAND: Introduce chip_probe function
Kyungmin Park [Fri, 28 May 2010 02:03:11 +0000]
mtd: OneNAND: Introduce chip_probe function

Samsung SoCs use the own OneNAND controler and detect OneNAND chip at power on.
To use this feature, introduce the chip_probe function.

Also remove workaround for Samsung SoCs.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: onenand:fix for page addr calculation based on device type
Rohit Hassan Sathyanarayan [Fri, 23 Jul 2010 06:59:25 +0000]
mtd: onenand:fix for page addr calculation based on device type

Sending the patch for page address calculation based on device type. This resolves the
OneNAND DDP device read problem as pointed by Enric.
http://lists.infradead.org/pipermail/linux-mtd/2010-July/030920.html

Signed-off-by: Rohit HS <rohit.hs@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: nand: update nand_default_block_markbad()
Brian Norris [Wed, 21 Jul 2010 23:53:47 +0000]
mtd: nand: update nand_default_block_markbad()

This is an update that depends on the previous patches I sent.

We can now write to all the appropriate BB marker locations (i.e.
pages 1 AND 2, bytes 1 AND 6) with nand_default_block_markbad() if
necessary, according to the flags marked in chip->options.

Note that I removed the line:
ofs += mtd->oobsize;
Unless I am wrong, this line was completely unnecessary in the
first place.

Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali.h: fixed checkpatch errors
Dong, Chuanxiao [Wed, 21 Jul 2010 17:32:26 +0000]
mtd: denali.h: fixed checkpatch errors

Fix all checkpatch.pl complaints.

Artem: tweaked a little and fix tab indentations, so now this is not
       only about checkpatch, but also about making indentations look
       sane.

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: nand: davinci: correct 4-bit error correction
Sudhakar Rajashekhara [Tue, 20 Jul 2010 22:24:01 +0000]
mtd: nand: davinci: correct 4-bit error correction

On TI's DA830/OMAP-L137, DA850/OMAP-L138 and DM365, after setting the
4BITECC_ADD_CALC_START bit in the NAND Flash control register to 1 and
before waiting for the NAND Flash status register to be equal to 1, 2 or
3, we have to wait till the ECC HW goes to correction state.  Without this
wait, ECC correction calculations will not be proper.

This has been tested on DA830/OMAP-L137, DA850/OMAP-L138, DM355 and DM365
EVMs.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: nand: more BB Detection refactoring and dynamic scan options
Brian Norris [Thu, 15 Jul 2010 19:15:44 +0000]
mtd: nand: more BB Detection refactoring and dynamic scan options

This is a revision to PATCH 2/2 that I sent. Link:
http://lists.infradead.org/pipermail/linux-mtd/2010-July/030911.html

Added new flag for scanning of both bytes 1 and 6 of the OOB for
a BB marker (instead of simply one or the other).

The "check_pattern" and "check_short_pattern" functions were updated
to include support for scanning the two different locations in the OOB.

In order to handle increases in variety of necessary scanning patterns,
I implemented dynamic memory allocation of nand_bbt_descr structs
in new function 'nand_create_default_bbt_descr()'. This replaces
some increasingly-unwieldy, statically-declared descriptors. It can
replace several more (e.g. "flashbased" structs). However, I do not
test the flashbased options personally.

How this was tested:

I referenced 30+ data sheets (covering 100+ parts), and I tested a
selection of 10 different chips to varying degrees. Particularly, I
tested the creation of bad-block descriptors and basic BB scanning on
three parts:

ST NAND04GW3B2D, 2K page
ST NAND128W3A, 512B page
Samsung K9F1G08U0A, 2K page

To test these, I wrote some fake bad block markers to the flash (in OOB
bytes 1, 6, and elsewhere) to see if the scanning routine would detect
them properly. However, this method was somewhat limited because the
driver I am using has some bugs in its OOB write functionality.

Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: nand: refactor BB marker detection
Brian Norris [Tue, 13 Jul 2010 22:13:00 +0000]
mtd: nand: refactor BB marker detection

Some level of support for various scanning locations was already built in,
but this required clean-up. First, BB marker location cannot be determined
_only_ by the page size. Instead, I implemented some heuristic detection
based on data sheets from various manufacturers (all found in
nand_base.c:nand_get_flash_type()).

Second, once these options were identified, they were not handled properly
by nand_bbt.c:nand_default_bbt(). I updated the static nand_bbt_desc structs
to reflect the need for more combinations of detection. The memory allocation
here probably needs to be done dynamically in the very near future (see next
patches).

Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: s3c nand: parsing command-line partitions prior to set->partitions
Conke Hu [Tue, 13 Jul 2010 04:56:30 +0000]
mtd: s3c nand: parsing command-line partitions prior to set->partitions

Current driver prevents command-line partitions from being parsed when built-in
partitions are defined in s3c2410_nand_set object, but it is not desirable in some
cases. This patch tries to parse commad-line partitions prior to the built-in.

Signed-off-by: Conke Hu <conke@maxwit.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: mxc_nand: fix unbalanced enable for IRQ
Eric Bénard [Thu, 10 Jun 2010 14:03:04 +0000]
mtd: mxc_nand: fix unbalanced enable for IRQ

* preset should be done before sending the reset command

* without this, I get the following error on an i.MX35 :
[    0.900000] ------------[ cut here ]------------
[    0.900000] WARNING: at kernel/irq/manage.c:290 __enable_irq+0x4c/0x88()
[    0.900000] Unbalanced enable for IRQ 33
[    0.900000] Modules linked in:
[    0.900000] [<c002ffb8>] (unwind_backtrace+0x0/0xf0) from [<c02f7d0c>] (dump_stack+0x18/0x1c)
[    0.900000] [<c02f7d0c>] (dump_stack+0x18/0x1c) from [<c0049a44>] (warn_slowpath_common+0x54/0x6c)
[    0.900000] [<c0049a44>] (warn_slowpath_common+0x54/0x6c) from [<c0049b00>] (warn_slowpath_fmt+0x38/0x40)
[    0.900000] [<c0049b00>] (warn_slowpath_fmt+0x38/0x40) from [<c008f65c>] (__enable_irq+0x4c/0x88)
[    0.900000] [<c008f65c>] (__enable_irq+0x4c/0x88) from [<c008fca0>] (enable_irq+0x54/0x98)
[    0.900000] [<c008fca0>] (enable_irq+0x54/0x98) from [<c021e618>] (wait_op_done+0x40/0x134)
[    0.900000] [<c021e618>] (wait_op_done+0x40/0x134) from [<c021e808>] (send_cmd+0x30/0x38)
[    0.900000] [<c021e808>] (send_cmd+0x30/0x38) from [<c021eb8c>] (mxc_nand_command+0x26c/0x328)
[    0.900000] [<c021eb8c>] (mxc_nand_command+0x26c/0x328) from [<c021aa60>] (nand_scan_ident+0x188/0x6c0)
[    0.900000] [<c021aa60>] (nand_scan_ident+0x188/0x6c0) from [<c001a9cc>] (mxcnd_probe+0x2b8/0x3d0)
[    0.900000] [<c001a9cc>] (mxcnd_probe+0x2b8/0x3d0) from [<c01f9e88>] (platform_drv_probe+0x20/0x24)
[    0.900000] [<c01f9e88>] (platform_drv_probe+0x20/0x24) from [<c01f8c38>] (driver_probe_device+0xb0/0x164)
[    0.900000] [<c01f8c38>] (driver_probe_device+0xb0/0x164) from [<c01f8d54>] (__driver_attach+0x68/0x8c)
[    0.900000] [<c01f8d54>] (__driver_attach+0x68/0x8c) from [<c01f8348>] (bus_for_each_dev+0x50/0x84)
[    0.900000] [<c01f8348>] (bus_for_each_dev+0x50/0x84) from [<c01f8a9c>] (driver_attach+0x20/0x28)
[    0.900000] [<c01f8a9c>] (driver_attach+0x20/0x28) from [<c01f7c00>] (bus_add_driver+0x144/0x2dc)
[    0.900000] [<c01f7c00>] (bus_add_driver+0x144/0x2dc) from [<c01f906c>] (driver_register+0xb0/0x13c)
[    0.900000] [<c01f906c>] (driver_register+0xb0/0x13c) from [<c01fa13c>] (platform_driver_register+0x4c/0x60)
[    0.900000] [<c01fa13c>] (platform_driver_register+0x4c/0x60) from [<c01fa170>] (platform_driver_probe+0x20/0xa0)
[    0.900000] [<c01fa170>] (platform_driver_probe+0x20/0xa0) from [<c001a708>] (mxc_nd_init+0x18/0x24)
[    0.900000] [<c001a708>] (mxc_nd_init+0x18/0x24) from [<c002938c>] (do_one_initcall+0x64/0x1bc)
[    0.900000] [<c002938c>] (do_one_initcall+0x64/0x1bc) from [<c00084c4>] (kernel_init+0xe8/0x1ac)
[    0.900000] [<c00084c4>] (kernel_init+0xe8/0x1ac) from [<c002aee8>] (kernel_thread_exit+0x0/0x8)
[    0.900000] ---[ end trace 8bf72ac6ba089a19 ]---
[    1.140000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: tests: return -1 if verify failed
Roel Kluin [Tue, 13 Jul 2010 10:24:31 +0000]
mtd: tests: return -1 if verify failed

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: sm_common: remove casts from void
Kulikov Vasiliy [Tue, 29 Jun 2010 10:15:24 +0000]
mtd: sm_common: remove casts from void

Remove unnesessary casts from void*.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: r852: remove casts from void
Kulikov Vasiliy [Tue, 29 Jun 2010 10:15:20 +0000]
mtd: r852: remove casts from void

Remove unnesessary casts from void*.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: nandsim: remove casts from void
Kulikov Vasiliy [Tue, 29 Jun 2010 10:15:17 +0000]
mtd: nandsim: remove casts from void

Remove unnesessary casts from void*.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: dataflash: remove casts from void
Kulikov Vasiliy [Tue, 29 Jun 2010 10:15:13 +0000]
mtd: dataflash: remove casts from void

Remove unnesessary casts from void*.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: r852: remove casts from void
Kulikov Vasiliy [Tue, 29 Jun 2010 10:14:57 +0000]
mtd: r852: remove casts from void

Remove unnesessary casts from void*.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: cfi_probe: print manufacturer and id of probed chip
Guillaume LECERF [Tue, 29 Jun 2010 08:32:37 +0000]
mtd: cfi_probe: print manufacturer and id of probed chip

Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: nand: edit macro flag for BBT scan of last page in block
Brian Norris [Wed, 23 Jun 2010 20:36:02 +0000]
mtd: nand: edit macro flag for BBT scan of last page in block

NAND_BB_LAST_PAGE used to be in nand.h, but it pertained to bad block
management and so belongs next to NAND_BBT_SCAN2NDPAGE in bbm.h. Also,
its previous flag value (0x00000400) conflicted with NAND_BBT_SCANALLPAGES
so I changed its value to 0x00008000. All uses of the name were modified to
provide consistency with other "NAND_BBT_*" flags.

Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: mtdconcat: fix bug with uninitialized lock and unlock functions
Martin Krause [Tue, 22 Jun 2010 13:00:19 +0000]
mtd: mtdconcat: fix bug with uninitialized lock and unlock functions

Test if a lock or unlock function is present (pointer not NULL) before
calling it, to prevent a kernel dump.

Artem: removed extra blank lines

Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: nand_ids: add two entries for NAND chips
Brian Norris [Thu, 17 Jun 2010 19:35:11 +0000]
mtd: nand_ids: add two entries for NAND chips

Included the basic size info for NAND chips with ID of 0xAD or
0xD7. The first can be found in Hynix HY27SF161G2M, while the
second can be found in Micron MT29F64G08 and the Samsung K9LBG08U0D
(among others). Also, some 64 Gbit (or larger) chips identify as
0xD7 because they contain multiple smaller 32 Gbit chips. I
assume it's safe to classify these under the 32 Gbit listing.

Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: mxc_nand: remove unused variable
Uwe Kleine-König [Mon, 14 Jun 2010 07:01:51 +0000]
mtd: mxc_nand: remove unused variable

This fixes:

drivers/mtd/nand/mxc_nand.c: In function 'mxcnd_resume':
drivers/mtd/nand/mxc_nand.c:901: warning: unused variable 'host'

Removing this variable was missed in 9c14b153e6af.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: physmap: use resource_size()
H Hartley Sweeten [Mon, 14 Jun 2010 16:57:54 +0000]
mtd: physmap: use resource_size()

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: add an ioctl to query the lock status of a flash sector
Richard Cochran [Mon, 14 Jun 2010 16:10:33 +0000]
mtd: add an ioctl to query the lock status of a flash sector

This patchs adds a way for user space programs to find out whether a
flash sector is locked. An optional driver method in the mtd_info struct
provides the information.

Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: denali: add Kconfig dependency
Karl Beldan [Sat, 12 Jun 2010 10:25:13 +0000]
mtd: denali: add Kconfig dependency

Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: m25p80: Add support for Macronix 25L8005
Martin Michlmayr [Mon, 7 Jun 2010 18:31:01 +0000]
mtd: m25p80: Add support for Macronix 25L8005

Add support for Macronix 25L8005.  Tested on a HP t5325 Thin Client.

Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: return success on blktrans_ioctl
Dan Carpenter [Mon, 31 May 2010 14:03:38 +0000]
mtd: return success on blktrans_ioctl

There was a break missing so we returned -ENOTTY on success instead of
zero.  This was introduced by 048d8719956: "mtd: blktrans: Hotplug fixes"

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: remove redundant dependency checks in Kconfig files
Kyle Spaans [Tue, 8 Jun 2010 13:48:22 +0000]
mtd: remove redundant dependency checks in Kconfig files

Look for dependency checks for "FOO" when inside of an "if FOO" block and remove them.

Signed-off-by: Kyle Spaans <kspaans@uwaterloo.ca>
Reviewed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: mxc_nand: fix OOB accesses on i.MX27
Sascha Hauer [Fri, 28 May 2010 08:02:17 +0000]
mtd: mxc_nand: fix OOB accesses on i.MX27

The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: sst25l: check for null consistently
Dan Carpenter [Sat, 22 May 2010 20:16:26 +0000]
mtd: sst25l: check for null consistently

The rest of the function assumes that "data" can be null.  I don't know
the code well enough to say whether it can actually be null, but there
is no harm in checking here.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agodrivers/mtd/maps: introduce missing kfree
Julia Lawall [Tue, 1 Jun 2010 14:34:20 +0000]
drivers/mtd/maps: introduce missing kfree

Error handling code following a kmalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@

x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...x...+> }
(
x->f1 = E
|
 (x->f1 == NULL || ...)
|
 f(...,x->f1,...)
)
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agoof/mtd: nand: fix build breakage in drivers
Anatolij Gustschin [Thu, 3 Jun 2010 00:37:17 +0000]
of/mtd: nand: fix build breakage in drivers

Fixes build errors in drivers caused by the OF device_node
pointer being moved into struct device

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agojffs2: Fix NFS race by using insert_inode_locked()
David Woodhouse [Thu, 3 Jun 2010 07:09:12 +0000]
jffs2: Fix NFS race by using insert_inode_locked()

New inodes need to be locked as we're creating them, so they don't get used
by other things (like NFSd) before they're ready.

Pointed out by Al Viro.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agojffs2: Fix in-core inode leaks on error paths
David Woodhouse [Thu, 3 Jun 2010 07:03:39 +0000]
jffs2: Fix in-core inode leaks on error paths

Pointed out by Al Viro.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd: Fix NAND submenu
Maxim Levitsky [Wed, 2 Jun 2010 15:22:48 +0000]
mtd: Fix NAND submenu

Move MTD_NAND_ECC and MTD_NAND_ECC_SMC above NAND memuconfig, to unbreak
display in xconfig. This shouldn't change any dependencies.

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd/r852: update card detect early.
Maxim Levitsky [Wed, 2 Jun 2010 13:01:47 +0000]
mtd/r852: update card detect early.

This turns out to be the reason for DMA timeouts on resume,
if card was inserted while system was suspended

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd/r852: Fixes in case of DMA timeout
Maxim Levitsky [Wed, 2 Jun 2010 13:01:46 +0000]
mtd/r852: Fixes in case of DMA timeout

* Don't call complete on dma completion
* do a INIT_COMPLETE before using it each time
* Report DMA read error via ecc 'correct'

I finally managed to make my system do suspend to ram propertly, and I see that
if card was inserted during suspend (while system was off), I get dma timeouts
on resume. Simple card reinsert solves the issue.
This patch solves a crash that would happen otherwise

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agomtd/r852: register IRQ as last step
Maxim Levitsky [Wed, 2 Jun 2010 13:01:45 +0000]
mtd/r852: register IRQ as last step

Otherwise, if it fires right away, it might access
uninitialized spinlock

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agodrivers/mtd: Use memdup_user
Julia Lawall [Sat, 22 May 2010 08:22:49 +0000]
drivers/mtd: Use memdup_user

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agodocbook: make mtd nand module init static
H Hartley Sweeten [Mon, 17 May 2010 23:21:11 +0000]
docbook: make mtd nand module init static

In the example the module_init function should be static.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

9 years agoMerge git://git.infradead.org/mtd-2.6
Linus Torvalds [Fri, 21 May 2010 14:25:43 +0000]
Merge git://git.infradead.org/mtd-2.6

* git://git.infradead.org/mtd-2.6: (154 commits)
  mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
  mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
  mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
  mtd: update gfp/slab.h includes
  jffs2: Stop triggering block erases from jffs2_write_super()
  jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
  jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
  jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
  jffs2: Wake GC thread when there are blocks to be erased
  jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
  jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
  mtd: mtdchar: Do not corrupt backing device of device node inode
  mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
  drivers/mtd: Use kmemdup
  mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
  mtd: nand: add Toshiba TC58NVG0 device ID
  pcmciamtd: add another ID
  pcmciamtd: coding style cleanups
  pcmciamtd: fixing obvious errors
  mtd: chips: add SST39WF160x NOR-flashes
  ...

Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c

9 years agoMerge branch 'linux-next' of git://git.infradead.org/ubi-2.6
Linus Torvalds [Fri, 21 May 2010 14:23:12 +0000]
Merge branch 'linux-next' of git://git.infradead.org/ubi-2.6

* 'linux-next' of git://git.infradead.org/ubi-2.6:
  UBI: misc comment fixes
  UBI: fix s/then/than/ typos
  UBI: init even if MTD device cannot be attached, if built into kernel
  UBI: remove reboot notifier

9 years agoMerge branch 'linux-next' of git://git.infradead.org/ubifs-2.6
Linus Torvalds [Fri, 21 May 2010 14:22:42 +0000]
Merge branch 'linux-next' of git://git.infradead.org/ubifs-2.6

* 'linux-next' of git://git.infradead.org/ubifs-2.6:
  UBIFS: mark VFS SB RO too

9 years agoMerge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
Linus Torvalds [Fri, 21 May 2010 14:22:11 +0000]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs

* 'for-linus' of git://oss.sgi.com/xfs/xfs: (54 commits)
  xfs: mark xfs_iomap_write_ helpers static
  xfs: clean up end index calculation in xfs_page_state_convert
  xfs: clean up mapping size calculation in __xfs_get_blocks
  xfs: clean up xfs_iomap_valid
  xfs: move I/O type flags into xfs_aops.c
  xfs: kill struct xfs_iomap
  xfs: report iomap_bn in block base
  xfs: report iomap_offset and iomap_bsize in block base
  xfs: remove iomap_delta
  xfs: remove iomap_target
  xfs: limit xfs_imap_to_bmap to a single mapping
  xfs: simplify buffer to transaction matching
  xfs: Make fiemap work in query mode.
  xfs: kill off l_sectbb_mask
  xfs: record log sector size rather than log2(that)
  xfs: remove dead XFS_LOUD_RECOVERY code
  xfs: removed unused XFS_QMOPT_ flags
  xfs: remove a few macro indirections in the quota code
  xfs: access quotainfo structure directly
  xfs: wait for direct I/O to complete in fsync and write_inode
  ...

9 years agoMerge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec...
Linus Torvalds [Fri, 21 May 2010 14:20:17 +0000]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jlbec/ocfs2

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (47 commits)
  ocfs2: Silence a gcc warning.
  ocfs2: Don't retry xattr set in case value extension fails.
  ocfs2:dlm: avoid dlm->ast_lock lockres->spinlock dependency break
  ocfs2: Reset xattr value size after xa_cleanup_value_truncate().
  fs/ocfs2/dlm: Use kstrdup
  fs/ocfs2/dlm: Drop memory allocation cast
  Ocfs2: Optimize punching-hole code.
  Ocfs2: Make ocfs2_find_cpos_for_left_leaf() public.
  Ocfs2: Fix hole punching to correctly do CoW during cluster zeroing.
  Ocfs2: Optimize ocfs2 truncate to use ocfs2_remove_btree_range() instead.
  ocfs2: Block signals for mkdir/link/symlink/O_CREAT.
  ocfs2: Wrap signal blocking in void functions.
  ocfs2/dlm: Increase o2dlm lockres hash size
  ocfs2: Make ocfs2_extend_trans() really extend.
  ocfs2/trivial: Code cleanup for allocation reservation.
  ocfs2: make ocfs2_adjust_resv_from_alloc simple.
  ocfs2: Make nointr a default mount option
  ocfs2/dlm: Make o2dlm domain join/leave messages KERN_NOTICE
  o2net: log socket state changes
  ocfs2: print node # when tcp fails
  ...

9 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Linus Torvalds [Fri, 21 May 2010 14:19:18 +0000]
Merge git://git./linux/kernel/git/jejb/scsi-misc-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
  [SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
  [SCSI] aacraid: prohibit access to array container space
  [SCSI] aacraid: add support for handling ATA pass-through commands.
  [SCSI] aacraid: expose physical devices for models with newer firmware
  [SCSI] aacraid: respond automatically to volumes added by config tool
  [SCSI] fcoe: fix fcoe module ref counting
  [SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
  [SCSI] libfcoe: Fix incorrect MAC address clearing
  [SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
  [SCSI] libfc: Move the port_id into lport
  [SCSI] fcoe: move link speed checking into its own routine
  [SCSI] libfc: Remove extra pointer check
  [SCSI] libfc: Remove unused fc_get_host_port_type
  [SCSI] fcoe: fixes wrong error exit in fcoe_create
  [SCSI] libfc: set seq_id for incoming sequence
  [SCSI] qla2xxx: Updates to ISP82xx support.
  [SCSI] qla2xxx: Optionally disable target reset.
  [SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
  [SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
  [SCSI] qla2xxx: T10 DIF support added.
  ...

9 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
Linus Torvalds [Fri, 21 May 2010 04:26:12 +0000]
Merge git://git./linux/kernel/git/gregkh/usb-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (229 commits)
  USB: remove unused usb_buffer_alloc and usb_buffer_free macros
  usb: musb: update gfp/slab.h includes
  USB: ftdi_sio: fix legacy SIO-device header
  USB: kl5usb105: reimplement using generic framework
  USB: kl5usb105: minor clean ups
  USB: kl5usb105: fix memory leak
  USB: io_ti: use kfifo to implement write buffering
  USB: io_ti: remove unsused private counter
  USB: ti_usb: use kfifo to implement write buffering
  USB: ir-usb: fix incorrect write-buffer length
  USB: aircable: fix incorrect write-buffer length
  USB: safe_serial: straighten out read processing
  USB: safe_serial: reimplement read using generic framework
  USB: safe_serial: reimplement write using generic framework
  usb-storage: always print quirks
  USB: usb-storage: trivial debug improvements
  USB: oti6858: use port write fifo
  USB: oti6858: use kfifo to implement write buffering
  USB: cypress_m8: use kfifo to implement write buffering
  USB: cypress_m8: remove unused drain define
  ...

Fix up conflicts (due to usb_buffer_alloc/free renaming) in
drivers/input/tablet/acecad.c
drivers/input/tablet/kbtab.c
drivers/input/tablet/wacom_sys.c
drivers/media/video/gspca/gspca.c
sound/usb/usbaudio.c

9 years agosound: fixup for usb_buffer_alloc/free rename
Stephen Rothwell [Fri, 30 Apr 2010 04:44:54 +0000]
sound: fixup for usb_buffer_alloc/free rename

This is needed before the USB merge.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

9 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
Linus Torvalds [Fri, 21 May 2010 04:04:44 +0000]
Merge git://git./linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
  qlcnic: adding co maintainer
  ixgbe: add support for active DA cables
  ixgbe: dcb, do not tag tc_prio_control frames
  ixgbe: fix ixgbe_tx_is_paused logic
  ixgbe: always enable vlan strip/insert when DCB is enabled
  ixgbe: remove some redundant code in setting FCoE FIP filter
  ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
  ixgbe: fix header len when unsplit packet overflows to data buffer
  ipv6: Never schedule DAD timer on dead address
  ipv6: Use POSTDAD state
  ipv6: Use state_lock to protect ifa state
  ipv6: Replace inet6_ifaddr->dead with state
  cxgb4: notify upper drivers if the device is already up when they load
  cxgb4: keep interrupts available when the ports are brought down
  cxgb4: fix initial addition of MAC address
  cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
  cnic: Convert cnic_local_flags to atomic ops.
  can: Fix SJA1000 command register writes on SMP systems
  bridge: fix build for CONFIG_SYSFS disabled
  ARCNET: Limit com20020 PCI ID matches for SOHARD cards
  ...

Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).

Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c

9 years agoMerge branch 'docs-next' of git://git.lwn.net/linux-2.6
Linus Torvalds [Thu, 20 May 2010 20:35:18 +0000]
Merge branch 'docs-next' of git://git.lwn.net/linux-2.6

* 'docs-next' of git://git.lwn.net/linux-2.6:
  Add a document describing the padata interface

9 years agoMerge branch 'viafb-next' of git://git.lwn.net/linux-2.6
Linus Torvalds [Thu, 20 May 2010 20:34:17 +0000]
Merge branch 'viafb-next' of git://git.lwn.net/linux-2.6

* 'viafb-next' of git://git.lwn.net/linux-2.6: (35 commits)
  viafb: move some include files to include/linux
  viafb: Eliminate some global.h references
  viafb: get rid of i2c debug cruft
  viafb: fold via_io.h into via-core.h
  viafb: Fix initialization error paths
  viafb: Do not remove gpiochip under spinlock
  viafb: make procfs entries optional
  viafb: fix proc entry removal
  viafb: improve misc register handling
  viafb: replace inb/outb
  viafb: move some modesetting functions to a seperate file
  viafb: unify modesetting functions
  viafb: Reserve framebuffer memory for the upcoming camera driver
  viafb: Add a simple VX855 DMA engine driver
  viafb: Add a simple interrupt management infrastructure
  via: Rationalize vt1636 detection
  viafb: Introduce viafb_find_i2c_adapter()
  via: Do not attempt I/O on inactive I2C adapters
  viafb: Turn GPIO and i2c into proper platform devices
  viafb: Convert GPIO and i2c to the new indexed port ops
  ...

9 years agoUSB: remove unused usb_buffer_alloc and usb_buffer_free macros
Greg Kroah-Hartman [Thu, 29 Apr 2010 22:46:07 +0000]
USB: remove unused usb_buffer_alloc and usb_buffer_free macros

Now that all callers are converted over, remove the compatibility
functions and all is good.

Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agousb: musb: update gfp/slab.h includes
Tejun Heo [Wed, 19 May 2010 15:44:20 +0000]
usb: musb: update gfp/slab.h includes

Implicit slab.h inclusion via percpu.h is about to go away.  Make sure
gfp.h or slab.h is included as necessary.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: ftdi_sio: fix legacy SIO-device header
Johan Hovold [Tue, 18 May 2010 22:01:41 +0000]
USB: ftdi_sio: fix legacy SIO-device header

Length field of header was incorrectly set to available payload space
rather than the actual payload size.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: kl5usb105: reimplement using generic framework
Johan Hovold [Tue, 18 May 2010 22:01:40 +0000]
USB: kl5usb105: reimplement using generic framework

Kill custom read and write implementations (static per-port,
singleton(!) urb pool).

Also remove changelog header (can be retrieved through git).

Read processing and write-buffer handling tested using a cp210x device
in a loopback setup.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: kl5usb105: minor clean ups
Johan Hovold [Tue, 18 May 2010 22:01:39 +0000]
USB: kl5usb105: minor clean ups

Whitespace changes and some removed comments.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>