8 years agobnx2x: disable dcb on 578xx since not supported yet
Dmitry Kravkov [Tue, 9 Aug 2011 03:11:13 +0000]
bnx2x: disable dcb on 578xx since not supported yet

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agobnx2x: properly clean indirect addresses
Dmitry Kravkov [Tue, 9 Aug 2011 03:10:29 +0000]
bnx2x: properly clean indirect addresses

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agobnx2x: prevent race between undi_unload and load flows
Dmitry Kravkov [Tue, 9 Aug 2011 03:09:52 +0000]
bnx2x: prevent race between undi_unload and load flows

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agobnx2x: fix select_queue when FCoE is disabled
Vladislav Zolotarov [Tue, 9 Aug 2011 03:08:55 +0000]
bnx2x: fix select_queue when FCoE is disabled

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agobnx2x: init FCOE FP only once
Vladislav Zolotarov [Tue, 9 Aug 2011 03:08:09 +0000]
bnx2x: init FCOE FP only once

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoipv4: some rt_iif -> rt_route_iif conversions
Julian Anastasov [Tue, 9 Aug 2011 04:01:16 +0000]
ipv4: some rt_iif -> rt_route_iif conversions

As rt_iif represents input device even for packets
coming from loopback with output route, it is not an unique
key specific to input routes. Now rt_route_iif has such role,
it was fl.iif in 2.6.38, so better to change the checks at
some places to save CPU cycles and to restore 2.6.38 semantics.

compare_keys:
- input routes: only rt_route_iif matters, rt_iif is same
- output routes: only rt_oif matters, rt_iif is not
used for matching in __ip_route_output_key
- now we are back to 2.6.38 state

ip_route_input_common:
- matching rt_route_iif implies input route
- compared to 2.6.38 we eliminated one rth->fl.oif check
because it was not needed even for 2.6.38

compare_hash_inputs:
Only the change here is not an optimization, it has
effect only for output routes. I assume I'm restoring
the original intention to ignore oif, it was using fl.iif
- now we are back to 2.6.38 state

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet/bridge/netfilter/ebtables.c: use available error handling code
Julia Lawall [Thu, 11 Aug 2011 01:59:38 +0000]
net/bridge/netfilter/ebtables.c: use available error handling code

Free the locally allocated table and newinfo as done in adjacent error
handling code.

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet/netlabel/netlabel_kapi.c: add missing cleanup code
Julia Lawall [Thu, 11 Aug 2011 00:06:04 +0000]
net/netlabel/netlabel_kapi.c: add missing cleanup code

Call cipso_v4_doi_putdef in the case of the failure of the allocation of
entry.  Reverse the order of the error handling code at the end of the
function and insert more labels in order to reduce the number of
unnecessary calls to kfree.

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet/irda: sh_sir: tidyup compile warning
Kuninori Morimoto [Wed, 10 Aug 2011 23:26:37 +0000]
net/irda: sh_sir: tidyup compile warning

This patch tidyup below warning

${LINUX}/drivers/net/irda/sh_sir.c:514:6: warning:
 'val' may be used uninitialized in this function

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet/irda: sh_sir: add missing header
Kuninori Morimoto [Wed, 10 Aug 2011 23:26:09 +0000]
net/irda: sh_sir: add missing header

This patch fixup below build error on sh_sir

sh_sir.c: In function 'sh_sir_write':
sh_sir.c:127:2: error: implicit declaration of function 'iowrite16'
sh_sir.c: In function 'sh_sir_read':
sh_sir.c:132:2: error: implicit declaration of function 'ioread16'
sh_sir.c: At top level:
sh_sir.c:561:20: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_sir_irq'
sh_sir.c: In function 'sh_sir_probe':
sh_sir.c:727:2: error: implicit declaration of function 'ioremap_nocache'
sh_sir.c:727:16: warning: assignment makes pointer from integer without a cast
sh_sir.c:762:2: error: implicit declaration of function 'request_irq'
sh_sir.c:762:23: error: 'sh_sir_irq' undeclared (first use in this function)
sh_sir.c:762:23: note: each undeclared identifier is reported only once for each function it appears in
sh_sir.c:762:35: error: 'IRQF_DISABLED' undeclared (first use in this function)
sh_sir.c:776:2: error: implicit declaration of function 'iounmap'
sh_sir.c: At top level:
sh_sir.c:436:13: warning: 'sh_sir_clear_all_err' defined but not used
sh_sir.c:474:12: warning: 'sh_sir_is_which_phase' defined but not used
sh_sir.c:490:13: warning: 'sh_sir_tx' defined but not used
sh_sir.c:540:13: warning: 'sh_sir_rx' defined but not used

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet/irda: sh_irda: add missing header
Kuninori Morimoto [Wed, 10 Aug 2011 23:25:42 +0000]
net/irda: sh_irda: add missing header

This patch fixup below build error on sh_irda

sh_irda.c: In function 'sh_irda_write':
sh_irda.c:174: error: implicit declaration of function 'iowrite16'
sh_irda.c: In function 'sh_irda_read':
sh_irda.c:184: error: implicit declaration of function 'ioread16'
sh_irda.c: At top level:
sh_irda.c:492: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_irda_irq'
sh_irda.c: In function 'sh_irda_probe':
sh_irda.c:776: error: implicit declaration of function 'ioremap_nocache'
sh_irda.c:776: warning: assignment makes pointer from integer without a cast
sh_irda.c:811: error: implicit declaration of function 'request_irq'
sh_irda.c:811: error: 'sh_irda_irq' undeclared (first use in this function)
sh_irda.c:811: error: (Each undeclared identifier is reported only once
sh_irda.c:811: error: for each function it appears in.)
sh_irda.c:811: error: 'IRQF_DISABLED' undeclared (first use in this function)
sh_irda.c:825: error: implicit declaration of function 'iounmap'

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoslcan: ldisc generated skbs are received in softirq context
Oliver Hartkopp [Wed, 10 Aug 2011 05:18:59 +0000]
slcan: ldisc generated skbs are received in softirq context

As this discussion pointed out

http://marc.info/?l=linux-netdev&m=131257225602375

netdevices that are based on serial line disciplines should use netif_rx_ni()
when pushing received socketbuffers into the netdev rx queue.

Following commit 614851601c121b1320a35757ab88292d6272f906 ("slip: fix NOHZ
local_softirq_pending 08 warning") this patch updates the slcan driver
accordingly.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Matvejchikov Ilya <matvejchikov@gmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoscm: Capture the full credentials of the scm sender
Tim Chen [Tue, 9 Aug 2011 06:48:32 +0000]
scm: Capture the full credentials of the scm sender

This patch corrects an erroneous update of credential's gid with uid
introduced in commit 257b5358b32f17 since 2.6.36.

Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agotcp: initialize variable ecn_ok in syncookies path
Mike Waychison [Thu, 11 Aug 2011 04:59:57 +0000]
tcp: initialize variable ecn_ok in syncookies path

Using a gcc 4.4.3, warnings are emitted for a possibly uninitialized use
of ecn_ok.

This can happen if cookie_check_timestamp() returns due to not having
seen a timestamp.  Defaulting to ecn off seems like a reasonable thing
to do in this case, so initialized ecn_ok to false.

Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet: add Documentation/networking/scaling.txt
Willem de Bruijn [Tue, 9 Aug 2011 04:20:48 +0000]
net: add Documentation/networking/scaling.txt

Describes RSS, RPS, RFS, accelerated RFS, and XPS.

This version incorporates comments by Randy Dunlap and Rick Jones.
Besides text cleanup, it adds an explicit "Suggested Configuration"
heading to each section.

Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-By: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet_sched: prio: use qdisc_dequeue_peeked
Florian Westphal [Tue, 9 Aug 2011 02:04:43 +0000]
net_sched: prio: use qdisc_dequeue_peeked

commit 07bd8df5df4369487812bf85a237322ff3569b77
(sch_sfq: fix peek() implementation) changed sfq to use generic
peek helper.

This makes HFSC complain about a non-work-conserving child qdisc, if
prio with sfq child is used within hfsc:

hfsc peeks into prio qdisc, which will then peek into sfq.
returned skb is stashed in sch->gso_skb.

Next, hfsc tries to dequeue from prio, but prio will call sfq dequeue
directly, which may return NULL instead of previously peeked-at skb.

Have prio call qdisc_dequeue_peeked, so sfq->dequeue() is
not called in this case.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoBridge: Always send NETDEV_CHANGEADDR up on br MAC change.
Andrei Warkentin [Fri, 5 Aug 2011 11:04:10 +0000]
Bridge: Always send NETDEV_CHANGEADDR up on br MAC change.

This ensures the neighbor entries associated with the bridge
dev are flushed, also invalidating the associated cached L2 headers.

This means we br_add_if/br_del_if ports to implement hand-over and
not wind up with bridge packets going out with stale MAC.

This means we can also change MAC of port device and also not wind
up with bridge packets going out with stale MAC.

This builds on Stephen Hemminger's patch, also handling the br_del_if
case and the port MAC change case.

Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agodp83640: increase receive time stamp buffer size
Richard Cochran [Sat, 6 Aug 2011 21:03:04 +0000]
dp83640: increase receive time stamp buffer size

The dp83640 buffers receive time stamps from special PHY status frames,
matching them to received PTP packets in a work queue. Because the timeout
for orphaned time stamps is so long and the buffer is so small, the driver
can drop time stamps under moderate PTP traffic.

This commit fixes the issue by decreasing the timeout to (at least) one
timer tick and increasing the buffer size.

Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agogianfar: fix fiper alignment after resetting the time
Richard Cochran [Sat, 6 Aug 2011 21:03:03 +0000]
gianfar: fix fiper alignment after resetting the time

After resetting the time, the PPS signals on the FIPER output channels
are incorrectly offset from the clock time, as can be readily verified
by a looping back the FIPER to the external time stamp input.

Despite its name, setting the "Fiper Realignment Disable" bit seems to
fix the problem, at least on the P2020.

Also, following the example code from the Freescale BSP, it is not really
necessary to disable and re-enable the timer in order to reprogram the
FIPER. (The documentation is rather unclear on this point. It seems that
writing to the alarm register also disables the FIPER.)

Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agortl8150: rtl8150_disconnect(...) does not need tasklet_disable(...)
huajun li [Sun, 7 Aug 2011 03:03:31 +0000]
rtl8150: rtl8150_disconnect(...) does not need tasklet_disable(...)

Executing cmd 'rmmod rtl8150' does not return(if your device connects
to host), the root cause is tasklet_disable() causes tasklet_kill()
block, remove it from rtl8150_disconnect().

Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoipv4: use dst with ref during bcast/mcast loopback
Julian Anastasov [Sun, 7 Aug 2011 10:17:22 +0000]
ipv4: use dst with ref during bcast/mcast loopback

Make sure skb dst has reference when moving to
another context. Currently, I don't see protocols that can
hit it when sending broadcasts/multicasts to loopback using
noref dsts, so it is just a precaution.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoipv4: route non-local sources for raw socket
Julian Anastasov [Sun, 7 Aug 2011 09:16:09 +0000]
ipv4: route non-local sources for raw socket

The raw sockets can provide source address for
routing but their privileges are not considered. We
can provide non-local source address, make sure the
FLOWI_FLAG_ANYSRC flag is set if socket has privileges
for this, i.e. based on hdrincl (IP_HDRINCL) and
transparent flags.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonetfilter: TCP and raw fix for ip_route_me_harder
Julian Anastasov [Sun, 7 Aug 2011 09:11:00 +0000]
netfilter: TCP and raw fix for ip_route_me_harder

TCP in some cases uses different global (raw) socket
to send RST and ACK. The transparent flag is not set there.
Currently, it is a problem for rerouting after the previous
change.

Fix it by simplifying the checks in ip_route_me_harder
and use FLOWI_FLAG_ANYSRC even for sockets. It looks safe
because the initial routing allowed this source address to
be used and now we just have to make sure the packet is rerouted.

As a side effect this also allows rerouting for normal
raw sockets that use spoofed source addresses which was not possible
even before we eliminated the ip_route_input call.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonet: Make userland include of netlink.h more sane.
David S. Miller [Mon, 8 Aug 2011 05:48:07 +0000]
net: Make userland include of netlink.h more sane.

Currently userland will barf when including linux/netlink.h unless it
precisely includes sys/socket.h first.  The issue is where the
definition of "sa_family_t" comes from.

We've been back and forth on how to fix this issue in the past, see:

http://thread.gmane.org/gmane.linux.debian.devel.bugs.general/622621
http://thread.gmane.org/gmane.linux.network/143380

Ben Hutchings suggested we take a hint from how we handle the
sockaddr_storage type.  First we define a "__kernel_sa_family_t"
to linux/socket.h that is always defined.

Then if __KERNEL__ is defined, we also define "sa_family_t" as
equal to "__kernel_sa_family_t".

Then in places like linux/netlink.h we use __kernel_sa_family_t
in user visible datastructures.

Reported-by: Michel Machado <michel@digirati.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoipv4: Fix ip_getsockopt for IP_PKTOPTIONS
Daniel Baluta [Mon, 8 Aug 2011 05:31:07 +0000]
ipv4: Fix ip_getsockopt for IP_PKTOPTIONS

IP_PKTOPTIONS is broken for 32-bit applications running
in COMPAT mode on 64-bit kernels.

This happens because msghdr's msg_flags field is always
set to zero. When running in COMPAT mode this should be
set to MSG_CMSG_COMPAT instead.

Signed-off-by: Tiberiu Szocs-Mihai <tszocs@ixiacom.com>
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agocompat_ioctl: add compat handler for PPPIOCGL2TPSTATS
Florian Westphal [Sat, 6 Aug 2011 12:12:04 +0000]
compat_ioctl: add compat handler for PPPIOCGL2TPSTATS

fixes following error seen on x86_64 kernel:
ioctl32(openl2tpd:7480): Unknown cmd fd(14) cmd(80487436){t:'t';sz:72} arg(ffa7e6c0) on socket:[105094]

The argument (struct pppol2tp_ioc_stats) uses "aligned_u64" and thus doesn't need
fixups.

Cc: James Chapman <jchapman@katalix.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoipv4: fix the reusing of routing cache entries
Julian Anastasov [Mon, 8 Aug 2011 05:20:20 +0000]
ipv4: fix the reusing of routing cache entries

compare_keys and ip_route_input_common rely on
rt_oif for distinguishing of input and output routes
with same keys values. But sometimes the input route has
also same hash chain (keyed by iif != 0) with the output
routes (keyed by orig_oif=0). Problem visible if running
with small number of rhash_entries.

Fix them to use rt_route_iif instead. By this way
input route can not be returned to users that request
output route.

The patch fixes the ip_rt_bug errors that were
reported in ip_local_out context, mostly for 255.255.255.255
destinations.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agobonding: document two undocumented options.
Nicolas de Pesloüan [Sat, 6 Aug 2011 07:06:39 +0000]
bonding: document two undocumented options.

Commit 655f8919d549ad1872e24d826b6ce42530516d2e
    bonding: add min links parameter to 802.3ad

and commit ebd8e4977a87cb81d93c62a9bff0102a9713722f
    bonding: add all_slaves_active parameter

introduced new options to bonding, but didn't provide the documentation
for those options.

V2: add the default value for both options.
V3: document the exact behavior of min_links default value.

Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoslip: fix NOHZ local_softirq_pending 08 warning
Matvejchikov Ilya [Fri, 5 Aug 2011 09:23:51 +0000]
slip: fix NOHZ local_softirq_pending 08 warning

When using nanosleep() in an userspace application we get a ratelimit warning:

NOHZ: local_softirq_pending 08

According to 481a8199142c050b72bff8a1956a49fd0a75bbe0 the problem is caused by
netif_rx() function. This patch replaces netif_rx() with netif_rx_ni() which
has to be used from process/softirq context.

Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agonetfilter: avoid double free in nf_reinject
Julian Anastasov [Fri, 5 Aug 2011 00:36:28 +0000]
netfilter: avoid double free in nf_reinject

NF_STOLEN means skb was already freed

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc
Linus Torvalds [Sun, 7 Aug 2011 22:52:19 +0000]
Merge git://git./linux/kernel/git/davem/sparc

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: Fix build with DEBUG_PAGEALLOC enabled.

8 years agosh: Fix boot crash related to SCI
Rafael J. Wysocki [Sun, 7 Aug 2011 22:26:50 +0000]
sh: Fix boot crash related to SCI

Commit d006199e72a9 ("serial: sh-sci: Regtype probing doesn't need to be
fatal.") made sci_init_single() return when sci_probe_regmap() succeeds,
although it should return when sci_probe_regmap() fails.  This causes
systems using the serial sh-sci driver to crash during boot.

Fix the problem by using the right return condition.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoarm: remove stale export of 'sha_transform'
Linus Torvalds [Sun, 7 Aug 2011 22:49:11 +0000]
arm: remove stale export of 'sha_transform'

The generic library code already exports the generic function, this was
left-over from the ARM-specific version that just got removed.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoarm: remove "optimized" SHA1 routines
Linus Torvalds [Sun, 7 Aug 2011 21:07:03 +0000]
arm: remove "optimized" SHA1 routines

Since commit 1eb19a12bd22 ("lib/sha1: use the git implementation of
SHA-1"), the ARM SHA1 routines no longer work.  The reason? They
depended on the larger 320-byte workspace, and now the sha1 workspace is
just 16 words (64 bytes).  So the assembly version would overwrite the
stack randomly.

The optimized asm version is also probably slower than the new improved
C version, so there's no reason to keep it around.  At least that was
the case in git, where what appears to be the same assembly language
version was removed two years ago because the optimized C BLK_SHA1 code
was faster.

Reported-and-tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agofix rcu annotations noise in cred.h
Al Viro [Sun, 7 Aug 2011 17:55:11 +0000]
fix rcu annotations noise in cred.h

task->cred is declared as __rcu, and access to other tasks' ->cred is,
indeed, protected.  Access to current->cred does not need rcu_dereference()
at all, since only the task itself can change its ->cred.  sparse, of
course, has no way of knowing that...

Add force-cast in current_cred(), make current_fsuid() et.al. use it.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agovfs: rename 'do_follow_link' to 'should_follow_link'
Linus Torvalds [Sun, 7 Aug 2011 16:53:20 +0000]
vfs: rename 'do_follow_link' to 'should_follow_link'

Al points out that the do_follow_link() helper function really is
misnamed - it's about whether we should try to follow a symlink or not,
not about actually doing the following.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoFix POSIX ACL permission check
Ari Savolainen [Sat, 6 Aug 2011 16:43:07 +0000]
Fix POSIX ACL permission check

After commit 3567866bf261: "RCUify freeing acls, let check_acl() go ahead in
RCU mode if acl is cached" posix_acl_permission is being called with an
unsupported flag and the permission check fails. This patch fixes the issue.

Signed-off-by: Ari Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

8 years agoMerge branch 'for-linus' of git://git.open-osd.org/linux-open-osd
Linus Torvalds [Sun, 7 Aug 2011 05:56:03 +0000]
Merge branch 'for-linus' of git://git.open-osd.org/linux-open-osd

* 'for-linus' of git://git.open-osd.org/linux-open-osd:
  ore: Make ore its own module
  exofs: Rename raid engine from exofs/ios.c => ore
  exofs: ios: Move to a per inode components & device-table
  exofs: Move exofs specific osd operations out of ios.c
  exofs: Add offset/length to exofs_get_io_state
  exofs: Fix truncate for the raid-groups case
  exofs: Small cleanup of exofs_fill_super
  exofs: BUG: Avoid sbi realloc
  exofs: Remove pnfs-osd private definitions
  nfs_xdr: Move nfs4_string definition out of #ifdef CONFIG_NFS_V4

8 years agovfs: optimize inode cache access patterns
Linus Torvalds [Sun, 7 Aug 2011 05:45:50 +0000]
vfs: optimize inode cache access patterns

The inode structure layout is largely random, and some of the vfs paths
really do care.  The path lookup in particular is already quite D$
intensive, and profiles show that accessing the 'inode->i_op->xyz'
fields is quite costly.

We already optimized the dcache to not unnecessarily load the d_op
structure for members that are often NULL using the DCACHE_OP_xyz bits
in dentry->d_flags, and this does something very similar for the inode
ops that are used during pathname lookup.

It also re-orders the fields so that the fields accessed by 'stat' are
together at the beginning of the inode structure, and roughly in the
order accessed.

The effect of this seems to be in the 1-2% range for an empty kernel
"make -j" run (which is fairly kernel-intensive, mostly in filename
lookup), so it's visible.  The numbers are fairly noisy, though, and
likely depend a lot on exact microarchitecture.  So there's more tuning
to be done.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agovfs: renumber DCACHE_xyz flags, remove some stale ones
Linus Torvalds [Sun, 7 Aug 2011 05:41:50 +0000]
vfs: renumber DCACHE_xyz flags, remove some stale ones

Gcc tends to generate better code with small integers, including the
DCACHE_xyz flag tests - so move the common ones to be first in the list.
Also just remove the unused DCACHE_INOTIFY_PARENT_WATCHED and
DCACHE_AUTOFS_PENDING values, their users no longer exists in the source
tree.

And add a "unlikely()" to the DCACHE_OP_COMPARE test, since we want the
common case to be a nice straight-line fall-through.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Linus Torvalds [Sun, 7 Aug 2011 05:12:37 +0000]
Merge git://git./linux/kernel/git/davem/net

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: Compute protocol sequence numbers and fragment IDs using MD5.
  crypto: Move md5_transform to lib/md5.c

8 years agoore: Make ore its own module
Boaz Harrosh [Sun, 7 Aug 2011 02:22:06 +0000]
ore: Make ore its own module

Export everything from ore need exporting. Change Kbuild and Kconfig
to build ore.ko as an independent module. Import ore from exofs

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

8 years agoexofs: Rename raid engine from exofs/ios.c => ore
Boaz Harrosh [Sun, 7 Aug 2011 02:26:31 +0000]
exofs: Rename raid engine from exofs/ios.c => ore

ORE stands for "Objects Raid Engine"

This patch is a mechanical rename of everything that was in ios.c
and its API declaration to an ore.c and an osd_ore.h header. The ore
engine will later be used by the pnfs objects layout driver.

* File ios.c => ore.c

* Declaration of types and API are moved from exofs.h to a new
  osd_ore.h

* All used types are prefixed by ore_ from their exofs_ name.

* Shift includes from exofs.h to osd_ore.h so osd_ore.h is
  independent, include it from exofs.h.

Other than a pure rename there are no other changes. Next patch
will move the ore into it's own module and will export the API
to be used by exofs and later the layout driver

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

8 years agoexofs: ios: Move to a per inode components & device-table
Boaz Harrosh [Fri, 5 Aug 2011 22:06:04 +0000]
exofs: ios: Move to a per inode components & device-table

Exofs raid engine was saving on memory space by having a single layout-info,
single pid, and a single device-table, global to the filesystem. Then passing
a credential and object_id info at the io_state level, private for each
inode. It would also devise this contraption of rotating the device table
view for each inode->ino to spread out the device usage.

This is not compatible with the pnfs-objects standard, demanding that
each inode can have it's own layout-info, device-table, and each object
component it's own pid, oid and creds.

So: Bring exofs raid engine to be usable for generic pnfs-objects use by:

* Define an exofs_comp structure that holds obj_id and credential info.

* Break up exofs_layout struct to an exofs_components structure that holds a
  possible array of exofs_comp and the array of devices + the size of the
  arrays.

* Add a "comps" parameter to get_io_state() that specifies the ids creds
  and device array to use for each IO.

  This enables to keep the layout global, but the device-table view, creds
  and IDs at the inode level. It only adds two 64bit to each inode, since
  some of these members already existed in another form.

* ios raid engine now access layout-info and comps-info through the passed
  pointers. Everything is pre-prepared by caller for generic access of
  these structures and arrays.

At the exofs Level:

* Super block holds an exofs_components struct that holds the device
  array, previously in layout. The devices there are in device-table
  order. The device-array is twice bigger and repeats the device-table
  twice so now each inode's device array can point to a random device
  and have a round-robin view of the table, making it compatible to
  previous exofs versions.

* Each inode has an exofs_components struct that is initialized at
  load time, with it's own view of the device table IDs and creds.
  When doing IO this gets passed to the io_state together with the
  layout.

While preforming this change. Bugs where found where credentials with the
wrong IDs where used to access the different SB objects (super.c). As well
as some dead code. It was never noticed because the target we use does not
check the credentials.

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

8 years agoexofs: Move exofs specific osd operations out of ios.c
Boaz Harrosh [Mon, 16 May 2011 12:26:47 +0000]
exofs: Move exofs specific osd operations out of ios.c

ios.c will be moving to an external library, for use by the
objects-layout-driver. Remove from it some exofs specific functions.

Also g_attr_logical_length is used both by inode.c and ios.c
move definition to the later, to keep it independent

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

8 years agoexofs: Add offset/length to exofs_get_io_state
Boaz Harrosh [Tue, 16 Nov 2010 18:09:58 +0000]
exofs: Add offset/length to exofs_get_io_state

In future raid code we will need to know the IO offset/length
and if it's a read or write to determine some of the array
sizes we'll need.

So add a new exofs_get_rw_state() API for use when
writeing/reading. All other simple cases are left using the
old way.

The major change to this is that now we need to call
exofs_get_io_state later at inode.c::read_exec and
inode.c::write_exec when we actually know these things. So this
patch is kept separate so I can test things apart from other
changes.

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

8 years agonet: Compute protocol sequence numbers and fragment IDs using MD5.
David S. Miller [Thu, 4 Aug 2011 03:50:44 +0000]
net: Compute protocol sequence numbers and fragment IDs using MD5.

Computers have become a lot faster since we compromised on the
partial MD4 hash which we use currently for performance reasons.

MD5 is a much safer choice, and is inline with both RFC1948 and
other ISS generators (OpenBSD, Solaris, etc.)

Furthermore, only having 24-bits of the sequence number be truly
unpredictable is a very serious limitation.  So the periodic
regeneration and 8-bit counter have been removed.  We compute and
use a full 32-bit sequence number.

For ipv6, DCCP was found to use a 32-bit truncated initial sequence
number (it needs 43-bits) and that is fixed here as well.

Reported-by: Dan Kaminsky <dan@doxpara.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agocrypto: Move md5_transform to lib/md5.c
David S. Miller [Thu, 4 Aug 2011 02:45:10 +0000]
crypto: Move md5_transform to lib/md5.c

We are going to use this for TCP/IP sequence number and fragment ID
generation.

Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6
Linus Torvalds [Sat, 6 Aug 2011 20:54:36 +0000]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: cope with negative dentries in cifs_get_root
  cifs: convert prefixpath delimiters in cifs_build_path_to_root
  CIFS: Fix missing a decrement of inFlight value
  cifs: demote DFS referral lookup errors to cFYI
  Revert "cifs: advertise the right receive buffer size to the server"

8 years agoMerge branch 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspe...
Linus Torvalds [Sat, 6 Aug 2011 20:26:37 +0000]
Merge branch 'pm-fixes' of git://git./linux/kernel/git/rafael/suspend-2.6

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM / Runtime: Allow _put_sync() from interrupts-disabled context
  PM / Domains: Fix pm_genpd_poweron()

8 years agoMerge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platf...
Linus Torvalds [Sat, 6 Aug 2011 20:26:15 +0000]
Merge branch 'for_linus' of git://git./linux/kernel/git/mjg59/platform-drivers-x86

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (38 commits)
  acer-wmi: support Lenovo ideapad S205 wifi switch
  acerhdf.c: spaces in aliased changed to *
  platform-drivers-x86: ideapad-laptop: add missing ideapad_input_exit in ideapad_acpi_add error path
  x86 driver: fix typo in TDP override enabling
  Platform: fix samsung-laptop DMI identification for N150/N210/220/N230
  dell-wmi: Add keys for Dell XPS L502X
  platform-drivers-x86: samsung-q10: make dmi_check_callback return 1
  Platform: Samsung Q10 backlight driver
  platform-drivers-x86: intel_scu_ipc: convert to DEFINE_PCI_DEVICE_TABLE
  platform-drivers-x86: intel_rar_register: convert to DEFINE_PCI_DEVICE_TABLE
  platform-drivers-x86: intel_menlow: add missing return AE_OK for intel_menlow_register_sensor()
  platform-drivers-x86: intel_mid_thermal: fix memory leak
  platform-drivers-x86: msi-wmi: add missing sparse_keymap_free in msi_wmi_init error path
  Samsung Laptop platform driver: support N510
  asus-wmi: add uwb rfkill support
  asus-wmi: add gps rfkill support
  asus-wmi: add CWAP support and clarify the meaning of WAPF bits
  asus-wmi: return proper value in store_cpufv()
  asus-wmi: check for temp1 presence
  asus-wmi: add thermal sensor
  ...

8 years agoMerge branch 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Sat, 6 Aug 2011 19:22:30 +0000]
Merge branch 'stable/bug.fixes' of git://git./linux/kernel/git/konrad/xen

* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/trace: Fix compile error when CONFIG_XEN_PRIVILEGED_GUEST is not set
  xen: Fix misleading WARN message at xen_release_chunk
  xen: Fix printk() format in xen/setup.c
  xen/tracing: it looks like we wanted CONFIG_FTRACE
  xen/self-balloon: Add dependency on tmem.
  xen/balloon: Fix compile errors - missing header files.
  xen/grant: Fix compile warning.
  xen/pciback: remove duplicated #include

8 years agoMerge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux...
Linus Torvalds [Sat, 6 Aug 2011 19:21:19 +0000]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  Battery: sysfs_remove_battery(): possible circular locking

8 years agosavagedb: Fix typo causing regression in savage4 series video chip detection
John Stanley [Thu, 4 Aug 2011 00:41:00 +0000]
savagedb: Fix typo causing regression in savage4 series video chip detection

Two additional savage4 variants were added, but the S3_SAVAGE4_SERIES
macro was incompletely modified, resulting in a false positive detection
of a savage4 card regardless of which savage card is actually present.

For non-savage4 series cards, such as a Savage/IX-MV card, this results
in garbled video and/or a hard-hang at boot time.  Fix this by changing
an '||' to an '&&' in the S3_SAVAGE4_SERIES macro.

Signed-off-by: John P. Stanley <jpsinthemix@verizon.net>
Reviewed-by: Tormod Volden <debian.tormod@gmail.com>
[ The macros have incomplete parenthesis too, but whatever ..  -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agoCodingStyle: Document the exception of not splitting user-visible strings, for grepping
Josh Triplett [Wed, 3 Aug 2011 19:19:07 +0000]
CodingStyle: Document the exception of not splitting user-visible strings, for grepping

Patch reviewers now recommend not splitting long user-visible strings,
such as printk messages, even if they exceed 80 columns.  This avoids
breaking grep.  However, that recommendation did not actually appear
anywhere in Documentation/CodingStyle.

See, for example, the thread at
  http://news.gmane.org/find-root.php?message_id=%3c1312215262.11635.15.camel%40Joe%2dLaptop%3e

Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agovfs: show O_CLOEXE bit properly in /proc/<pid>/fdinfo/<fd> files
Linus Torvalds [Sat, 6 Aug 2011 18:51:33 +0000]
vfs: show O_CLOEXE bit properly in /proc/<pid>/fdinfo/<fd> files

The CLOEXE bit is magical, and for performance (and semantic) reasons we
don't actually maintain it in the file descriptor itself, but in a
separate bit array.  Which means that when we show f_flags, the CLOEXE
status is shown incorrectly: we show the status not as it is now, but as
it was when the file was opened.

Fix that by looking up the bit properly in the 'fdt->close_on_exec' bit
array.

Uli needs this in order to re-implement the pfiles program:

  "For normal file descriptors (not sockets) this was the last piece of
   information which wasn't available.  This is all part of my 'give
   Solaris users no reason to not switch' effort.  I intend to offer the
   code to the util-linux-ng maintainers."

Requested-by: Ulrich Drepper <drepper@akkadia.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agooom_ajd: don't use WARN_ONCE, just use printk_once
Linus Torvalds [Sat, 6 Aug 2011 18:43:08 +0000]
oom_ajd: don't use WARN_ONCE, just use printk_once

WARN_ONCE() is very annoying, in that it shows the stack trace that we
don't care about at all, and also triggers various user-level "kernel
oopsed" logic that we really don't care about.  And it's not like the
user can do anything about the applications (sshd) in question, it's a
distro issue.

Requested-by: Andi Kleen <andi@firstfloor.org> (and many others)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agolib/sha1: use the git implementation of SHA-1
Mandeep Singh Baines [Sat, 6 Aug 2011 01:46:27 +0000]
lib/sha1: use the git implementation of SHA-1

For ChromiumOS, we use SHA-1 to verify the integrity of the root
filesystem.  The speed of the kernel sha-1 implementation has a major
impact on our boot performance.

To improve boot performance, we investigated using the heavily optimized
sha-1 implementation used in git.  With the git sha-1 implementation, we
see a 11.7% improvement in boot time.

10 reboots, remove slowest/fastest.

Before:

  Mean: 6.58 seconds Stdev: 0.14

After (with git sha-1, this patch):

  Mean: 5.89 seconds Stdev: 0.07

The other cool thing about the git SHA-1 implementation is that it only
needs 64 bytes of stack for the workspace while the original kernel
implementation needed 320 bytes.

Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Ramsay Jones <ramsay@ramsay1.demon.co.uk>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

8 years agosparc: Fix build with DEBUG_PAGEALLOC enabled.
David S. Miller [Sat, 6 Aug 2011 12:26:35 +0000]
sparc: Fix build with DEBUG_PAGEALLOC enabled.

arch/sparc/mm/init_64.c:1622:22: error: unused variable '__swapper_4m_tsb_phys_patch_end' [-Werror=unused-variable]
arch/sparc/mm/init_64.c:1621:22: error: unused variable '__swapper_4m_tsb_phys_patch' [-Werror=unused-variable]

Signed-off-by: David S. Miller <davem@davemloft.net>

8 years agoMerge branch 'battery' into release
Len Brown [Sat, 6 Aug 2011 02:16:42 +0000]
Merge branch 'battery' into release

8 years agoBattery: sysfs_remove_battery(): possible circular locking
Sergey Senozhatsky [Fri, 5 Aug 2011 22:34:08 +0000]
Battery: sysfs_remove_battery(): possible circular locking

Commit 9c921c22a7f33397a6774d7fa076db9b6a0fd669
Author: Lan Tianyu <tianyu.lan@intel.com>

    ACPI / Battery: Resolve the race condition in the sysfs_remove_battery()

fixed BUG https://bugzilla.kernel.org/show_bug.cgi?id=35642 , but as a side
effect made lockdep unhappy with sysfs_remove_battery():

[14818.477168]
[14818.477170] =======================================================
[14818.477200] [ INFO: possible circular locking dependency detected ]
[14818.477221] 3.1.0-dbg-07865-g1280ea8-dirty #668
[14818.477236] -------------------------------------------------------
[14818.477257] s2ram/1599 is trying to acquire lock:
[14818.477276]  (s_active#8){++++.+}, at: [<ffffffff81169147>] sysfs_addrm_finish+0x31/0x5a
[14818.477323]
[14818.477325] but task is already holding lock:
[14818.477350]  (&battery->lock){+.+.+.}, at: [<ffffffffa0047278>] sysfs_remove_battery+0x10/0x4b [battery]
[14818.477395]
[14818.477397] which lock already depends on the new lock.
[14818.477399]
[..]
[14818.479121] stack backtrace:
[14818.479148] Pid: 1599, comm: s2ram Not tainted 3.1.0-dbg-07865-g1280ea8-dirty #668
[14818.479175] Call Trace:
[14818.479198]  [<ffffffff814828c3>] print_circular_bug+0x293/0x2a4
[14818.479228]  [<ffffffff81070cb5>] __lock_acquire+0xfe4/0x164b
[14818.479260]  [<ffffffff81169147>] ? sysfs_addrm_finish+0x31/0x5a
[14818.479288]  [<ffffffff810718d2>] lock_acquire+0x138/0x1ac
[14818.479316]  [<ffffffff81169147>] ? sysfs_addrm_finish+0x31/0x5a
[14818.479345]  [<ffffffff81168a79>] sysfs_deactivate+0x9b/0xec
[14818.479373]  [<ffffffff81169147>] ? sysfs_addrm_finish+0x31/0x5a
[14818.479405]  [<ffffffff81169147>] sysfs_addrm_finish+0x31/0x5a
[14818.479433]  [<ffffffff81167bc5>] sysfs_hash_and_remove+0x54/0x77
[14818.479461]  [<ffffffff811681b9>] sysfs_remove_file+0x12/0x14
[14818.479488]  [<ffffffff81385bf8>] device_remove_file+0x12/0x14
[14818.479516]  [<ffffffff81386504>] device_del+0x119/0x17c
[14818.479542]  [<ffffffff81386575>] device_unregister+0xe/0x1a
[14818.479570]  [<ffffffff813c6ef9>] power_supply_unregister+0x23/0x27
[14818.479601]  [<ffffffffa004729c>] sysfs_remove_battery+0x34/0x4b [battery]
[14818.479632]  [<ffffffffa004778f>] battery_notify+0x2c/0x3a [battery]
[14818.479662]  [<ffffffff8148fe82>] notifier_call_chain+0x74/0xa1
[14818.479692]  [<ffffffff810624b4>] __blocking_notifier_call_chain+0x6c/0x89
[14818.479722]  [<ffffffff810624e0>] blocking_notifier_call_chain+0xf/0x11
[14818.479751]  [<ffffffff8107e40e>] pm_notifier_call_chain+0x15/0x27
[14818.479770]  [<ffffffff8107ee1a>] enter_state+0xa7/0xd5
[14818.479782]  [<ffffffff8107e341>] state_store+0xaa/0xc0
[14818.479795]  [<ffffffff8107e297>] ? pm_async_store+0x45/0x45
[14818.479807]  [<ffffffff81248837>] kobj_attr_store+0x17/0x19
[14818.479820]  [<ffffffff81167e27>] sysfs_write_file+0x103/0x13f
[14818.479834]  [<ffffffff81109037>] vfs_write+0xad/0x13d
[14818.479847]  [<ffffffff811092b2>] sys_write+0x45/0x6c
[14818.479860]  [<ffffffff81492f92>] system_call_fastpath+0x16/0x1b

This patch introduces separate lock to struct acpi_battery to
grab in sysfs_remove_battery() instead of battery->lock.
So fix by Lan Tianyu is still there, we just grab independent lock.

Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

8 years agoPM / Runtime: Allow _put_sync() from interrupts-disabled context
Kevin Hilman [Fri, 5 Aug 2011 19:45:20 +0000]
PM / Runtime: Allow _put_sync() from interrupts-disabled context

Currently the use of pm_runtime_put_sync() is not safe from
interrupts-disabled context because rpm_idle() will release the
spinlock and enable interrupts for the idle callbacks.  This enables
interrupts during a time where interrupts were expected to be
disabled, and can have strange side effects on drivers that expected
interrupts to be disabled.

This is not a bug since the documentation clearly states that only
_put_sync_suspend() is safe in IRQ-safe mode.

However, pm_runtime_put_sync() could be made safe when in IRQ-safe
mode by releasing the spinlock but not re-enabling interrupts, which
is what this patch aims to do.

Problem was found when using some buggy drivers that set
pm_runtime_irq_safe() and used _put_sync() in interrupts-disabled
context.

Reported-by: Colin Cross <ccross@google.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

8 years agoPM / Domains: Fix pm_genpd_poweron()
Rafael J. Wysocki [Fri, 5 Aug 2011 19:45:11 +0000]
PM / Domains: Fix pm_genpd_poweron()

The local variable ret is defined twice in pm_genpd_poweron(), which
causes this function to always return 0, even if the PM domain's
.power_on() callback fails, in which case an error code should be
returned.

Remove the wrong second definition of ret and additionally remove an
unnecessary definition of wait from pm_genpd_poweron().

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

8 years agoacer-wmi: support Lenovo ideapad S205 wifi switch
Lee, Chun-Yi [Sat, 30 Jul 2011 09:00:45 +0000]
acer-wmi: support Lenovo ideapad S205 wifi switch

The AMW0 function in acer-wmi works on Lenovo ideapad S205 for control
the wifi hardware state. We also found there have a 0x78 EC register
exposes the state of wifi hardware switch on the machine.

So, add this patch to support Lenovo ideapad S205 wifi hardware switch
in acer-wmi driver.

Reference: bko#37892
https://bugzilla.kernel.org/show_bug.cgi?id=37892

Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Tested-by: Florian Heyer <heyho@flanto.de>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoacerhdf.c: spaces in aliased changed to *
Anton V. Boyarshinov [Thu, 28 Jul 2011 14:05:35 +0000]
acerhdf.c: spaces in aliased changed to *

It seems that aliases shouldn't contain spaces, as
module-init-tools uses them as delimeters in module.alias file

Signed-off-by: Anton V. Boyarshinov <boyarsh@altlinux.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoplatform-drivers-x86: ideapad-laptop: add missing ideapad_input_exit in ideapad_acpi_...
Axel Lin [Wed, 27 Jul 2011 07:27:34 +0000]
platform-drivers-x86: ideapad-laptop: add missing ideapad_input_exit in ideapad_acpi_add error path

In the case of ideapad_backlight_init() failure,
we need to free the resources allocated by ideapad_input_init().

Aslo drop __devexit annotation for ideapad_input_exit() because
we also call it in ideapad_acpi_add() error path.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agox86 driver: fix typo in TDP override enabling
Jesse Barnes [Fri, 22 Jul 2011 16:21:36 +0000]
x86 driver: fix typo in TDP override enabling

When enabling turbo, we need to set both the TDC and TDP bits.  IIRC
only the TDC one actually matters, but fix it up anyway since the
current code is confusing.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoPlatform: fix samsung-laptop DMI identification for N150/N210/220/N230
Thomas Courbon [Wed, 20 Jul 2011 20:57:44 +0000]
Platform: fix samsung-laptop DMI identification for N150/N210/220/N230

Some samsung latop of the N150/N2{10,20,30} serie are badly detected by the samsung-laptop platform driver, see bug # 36082.
It appears that N230 identifies itself as N150/N210/N220/N230 whereas the other identify themselves as N150/N210/220.
This patch attemtp fix #36082 allowing correct identification for all the said netbook model.

Reported-by: Daniel Eklöf <daniel@ekloef.se>
Signed-off-by: Thomas Courbon <thcourbon@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agodell-wmi: Add keys for Dell XPS L502X
Seth Forshee [Mon, 1 Aug 2011 20:46:10 +0000]
dell-wmi: Add keys for Dell XPS L502X

All of these keys are being reported on the keyboard
controller but are also generating WMI events. Add them
to the legacy keymap to silence the noise.

BugLink: http://bugs.launchpad.net/bugs/815914
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoplatform-drivers-x86: samsung-q10: make dmi_check_callback return 1
Axel Lin [Mon, 18 Jul 2011 08:08:21 +0000]
platform-drivers-x86: samsung-q10: make dmi_check_callback return 1

We only care about if there is any successful match from the dmi table
or no match at all, we can make dmi_check_system return immediately if
we have a successful match instead of iterate thorough the whole table.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoPlatform: Samsung Q10 backlight driver
Frederick van der Wyck [Thu, 7 Jul 2011 21:05:25 +0000]
Platform: Samsung Q10 backlight driver

This adds backlight control on the Samsung Q10 laptop, which does not support
the SABI interface. Also tested successfully on the Dell Latitude X200.

Signed-off-by: Frederick van der Wyck <fvanderwyck@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoplatform-drivers-x86: intel_scu_ipc: convert to DEFINE_PCI_DEVICE_TABLE
Axel Lin [Thu, 7 Jul 2011 02:22:46 +0000]
platform-drivers-x86: intel_scu_ipc: convert to DEFINE_PCI_DEVICE_TABLE

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoplatform-drivers-x86: intel_rar_register: convert to DEFINE_PCI_DEVICE_TABLE
Axel Lin [Thu, 7 Jul 2011 02:21:15 +0000]
platform-drivers-x86: intel_rar_register: convert to DEFINE_PCI_DEVICE_TABLE

And also remove unused variable 'my_id_table'.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoplatform-drivers-x86: intel_menlow: add missing return AE_OK for intel_menlow_registe...
Axel Lin [Thu, 7 Jul 2011 02:05:49 +0000]
platform-drivers-x86: intel_menlow: add missing return AE_OK for intel_menlow_register_sensor()

Otherwise, the error path will always be executed.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoplatform-drivers-x86: intel_mid_thermal: fix memory leak
Axel Lin [Wed, 6 Jul 2011 15:40:51 +0000]
platform-drivers-x86: intel_mid_thermal: fix memory leak

The memory for td_info which is allocated in initialize_sensor()
should be properly kfreed in mid_thermal_probe() error patch and
mid_thermal_remove().

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoplatform-drivers-x86: msi-wmi: add missing sparse_keymap_free in msi_wmi_init error...
Axel Lin [Wed, 6 Jul 2011 03:05:20 +0000]
platform-drivers-x86: msi-wmi: add missing sparse_keymap_free in msi_wmi_init error path

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoSamsung Laptop platform driver: support N510
J Witteveen [Sun, 3 Jul 2011 11:15:44 +0000]
Samsung Laptop platform driver: support N510

The N510 benefits from this code as well. Below is a patch to include support.

Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: add uwb rfkill support
Corentin Chary [Fri, 1 Jul 2011 09:34:41 +0000]
asus-wmi: add uwb rfkill support

Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: add gps rfkill support
Corentin Chary [Fri, 1 Jul 2011 09:34:40 +0000]
asus-wmi: add gps rfkill support

Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: add CWAP support and clarify the meaning of WAPF bits
Corentin Chary [Fri, 1 Jul 2011 09:34:39 +0000]
asus-wmi: add CWAP support and clarify the meaning of WAPF bits

ref: http://dev.iksaif.net/projects/3/wiki/Asus-laptop_WAPF

Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: return proper value in store_cpufv()
Corentin Chary [Fri, 1 Jul 2011 09:34:38 +0000]
asus-wmi: return proper value in store_cpufv()

Cc: stable@kernel.org
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: check for temp1 presence
Corentin Chary [Fri, 1 Jul 2011 09:34:37 +0000]
asus-wmi: check for temp1 presence

Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: add thermal sensor
Corentin Chary [Fri, 1 Jul 2011 09:34:36 +0000]
asus-wmi: add thermal sensor

Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: add some device ids
Corentin Chary [Fri, 1 Jul 2011 09:34:35 +0000]
asus-wmi: add some device ids

Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: fix keyboard backlight detection
Corentin Chary [Fri, 1 Jul 2011 09:34:34 +0000]
asus-wmi: fix keyboard backlight detection

Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: fix section mismatch
Corentin Chary [Fri, 1 Jul 2011 09:34:32 +0000]
asus-wmi: fix section mismatch

Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: add keyboard backlight support
Corentin Chary [Fri, 1 Jul 2011 09:34:31 +0000]
asus-wmi: add keyboard backlight support

Based on a patch from Nate Weibley. <nweibley@gmail.com>.

Cc: Nate Weibley <nweibley@gmail.com>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: second part of the version starts at 16 not 8
Corentin Chary [Fri, 1 Jul 2011 09:34:30 +0000]
asus-wmi: second part of the version starts at 16 not 8

Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: Enable autorepeat for hotkey input device
Seth Forshee [Mon, 4 Jul 2011 07:49:20 +0000]
asus-wmi: Enable autorepeat for hotkey input device

The T101MT Home/Express Gate key autorepeats in hardware, but
sparse-keymap does not support hardware autorepeat. Enable the
input core's software autorepeat to emulate the hardware behavior.
Normal hotkeys are autoreleased, so the behavior of these keys
will not be affected.

Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoeeepc-wmi: Add support for T101MT Home/Express Gate key
Seth Forshee [Fri, 1 Jul 2011 09:34:28 +0000]
eeepc-wmi: Add support for T101MT Home/Express Gate key

This key is different than other hotkeys, having seperate scan
codes for press, release, and hold, so it requires some special
filtering. Press and release events are passed on, and hold events
are ignored since sparse-keymap does not support hardware
autorepeat.

Note that "Home" in the context of this button doesn't mean the
same thing as the usual Home key, and it really isn't clear at
all what is meant by "Home". The manufacurer's description of the
button indicates that it should launch some sort of touch screen
settings interface on short press and apply a desktop rotation on
long press.

Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: Add callback for hotkey filtering
Seth Forshee [Fri, 1 Jul 2011 09:34:27 +0000]
asus-wmi: Add callback for hotkey filtering

This is required for the T101MT home key, which behaves differently
than other hotkeys.

Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoasus-wmi: fix hwmon/pwm1
Corentin Chary [Fri, 1 Jul 2011 09:34:26 +0000]
asus-wmi: fix hwmon/pwm1

The code was completly broken, and should never had been sent
to the kernel. That's what happens when you write code without
hardware to test it.

Cc: stable@kernel.org
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoideapad: add backlight driver
Ike Panhc [Thu, 30 Jun 2011 11:50:52 +0000]
ideapad: add backlight driver

When acpi_backlight=vendor in cmdline or no backlight support in acpi video
device, ideapad-laptop will register backlight device and control brightness
and backlight power via the command in VPC2004.

Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoideapad: let camera_power node invisiable if no camera
Ike Panhc [Thu, 30 Jun 2011 11:50:47 +0000]
ideapad: let camera_power node invisiable if no camera

Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoideapad: define cfg bits and create sysfs node for cfg
Ike Panhc [Thu, 30 Jun 2011 11:50:40 +0000]
ideapad: define cfg bits and create sysfs node for cfg

Create /sys/devices/platform/ideapad/cfg for showing cfg value.

Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoAdd KEY_MICMUTE and enable it on Lenovo X220
Andy Lutomirski [Tue, 24 May 2011 19:16:43 +0000]
Add KEY_MICMUTE and enable it on Lenovo X220

I suspect that this works on T410.

Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agomsi-laptop: add MSI U270 netbook to module alias and scm list
Lee, Chun-Yi [Fri, 10 Jun 2011 07:24:26 +0000]
msi-laptop: add MSI U270 netbook to module alias and scm list

After test, msi-laptop driver also can support MSI U270 netbook.
So, add MSI U270's dmi information to module alias and scm table
for support this machine.

Tested on MSI U270 netbook.

Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoacer-wmi: Add support for Aspire 1830 wlan hotkey
Seth Forshee [Tue, 21 Jun 2011 17:00:32 +0000]
acer-wmi: Add support for Aspire 1830 wlan hotkey

Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>

8 years agoacerhdf: add support for Aspire 1810TZ BIOS v1.3314
Julien Valroff [Fri, 24 Jun 2011 12:47:17 +0000]
acerhdf: add support for Aspire 1810TZ BIOS v1.3314

Would you please consider applying the following patch adding support for
the Aspire 1810TZ BIOS v.1.3314 version to the acerhdf module and avoids the
following error:

acerhdf: unknown (unsupported) BIOS version Acer/Aspire 1810TZ/v1.3314, ple=
ase report, aborting!

Not sure about the other Aspire models, but it seems at least 1810T should
also be updated.

Signed-off-by: Julien Valroff <julien@kirya.net>

8 years agoplatform-drivers-x86: dell-laptop: Remove unneeded mutex_init() for buffer_mutex
Axel Lin [Wed, 8 Jun 2011 06:56:42 +0000]
platform-drivers-x86: dell-laptop: Remove unneeded mutex_init() for buffer_mutex

DEFINE_MUTEX() will automatically initialize buffer_mutex,
no need to call mutex_init() in dell_init().

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>