10 years agoqlge: Fix bug in firmware event handler.
Ron Mercer [Sun, 7 Jun 2009 13:58:26 +0000]
qlge: Fix bug in firmware event handler.

Each firmware mailbox command can have a different number of
valid data elements. When waiting for a mailbox command to
complete it the process passes it's element count and
waits for the completion.  It is possible that while waiting
an unrelated firmware async event (AE) can arrive.  When this
happens, the handler will over write the element count
with the value for the newly arrived AE. This can cause
the mailbox command to not get all of it's data.
This patch restores original mailbox count at the end
of the handler.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoqlge: Fix firmware event handler loop.
Ron Mercer [Sun, 7 Jun 2009 13:58:25 +0000]
qlge: Fix firmware event handler loop.

Check status on every iteration of event handler loop and exit
if an error occurred.  If an error occurred then recover process
will be queued so this loop should no continue.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetdev: smsc911x: add missing __devexit_p() usage
Mike Frysinger [Fri, 5 Jun 2009 14:37:20 +0000]
netdev: smsc911x: add missing __devexit_p() usage

The smsc911x_drv_remove() function is declared with __devexit, so the
assignment to the driver structure needs __devexit_p() wrappings to prevent
build failure when hotplug is disabled.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetdev: smsc911x: allow building on Blackfin systems
Mike Frysinger [Fri, 5 Jun 2009 14:37:19 +0000]
netdev: smsc911x: allow building on Blackfin systems

The smsc911x driver works fine on Blackfin systems, so add it to the arch
list in the Kconfig.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Increase the driver version number
Peter P Waskiewicz Jr [Thu, 4 Jun 2009 16:02:44 +0000]
ixgbe: Increase the driver version number

With all the last patchsets going in for 82599 feature enablement, the
driver version needs to be increased for better identification.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Add FW detection and warning for 82599 SFP+ adapters
Peter P Waskiewicz Jr [Thu, 4 Jun 2009 16:02:24 +0000]
ixgbe: Add FW detection and warning for 82599 SFP+ adapters

82599 has a FW running that helps manage the internal SFI PHY.  There are
also a number of pre-production samples of these SFI-based devices in the
field.  This patch adds a check to look for the firmware running on all
SFP+ based adapters, and displays a warning to the system log if a
pre-production adapter is identified.  The driver will continue loading
though, with no functional degradation.

Also remove an old function prototype from ixgbe_82599.c that isn't being
used.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Re-adjust ring layouts to have better cacheline efficiency
Jesse Brandeburg [Thu, 4 Jun 2009 16:02:04 +0000]
ixgbe: Re-adjust ring layouts to have better cacheline efficiency

This patch rearranges the ixgbe_ring struct to make better use of
cacheline efficiency.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Enable Flow Director hashing in 82599
Peter P Waskiewicz Jr [Thu, 4 Jun 2009 16:01:43 +0000]
ixgbe: Enable Flow Director hashing in 82599

This patch enables Flow Director's ATR functionality to the main base
driver for 82599.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Add Flow Director init and modify functions for 82599
Peter P Waskiewicz Jr [Thu, 4 Jun 2009 16:01:25 +0000]
ixgbe: Add Flow Director init and modify functions for 82599

This patch adds the functions for ixgbe to initialize Flow Director.  It
also has the function APIs to add Flow Director filters from the base
driver.  This also includes ATR, Application Targeted Routing, which is a
feature set of Flow Director.  This is the hash-based mechanism to
automatically identify flows and add filters based on the hash, and direct
the Rx of that flow back to that same CPU.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Add hardware defines for Flow Director for 82599
Peter P Waskiewicz Jr [Thu, 4 Jun 2009 16:01:06 +0000]
ixgbe: Add hardware defines for Flow Director for 82599

Flow Director is a Rx filter mechanism designed to match Rx flows back to
the same CPU that the flow's Tx occurred from.  This patch adds the first
piece, the defines for the hardware registers, to enable this feature in
82599 hardware.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Add a second feature flags variable, move HW RSC capability there
Peter P Waskiewicz Jr [Thu, 4 Jun 2009 16:00:47 +0000]
ixgbe: Add a second feature flags variable, move HW RSC capability there

This adds a second feature flag variable to use for future feature
expansion.  Add HW RSC to this new feature flags variable.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: move tx processing into NAPI context
Alexander Duyck [Thu, 4 Jun 2009 16:00:27 +0000]
ixgbe: move tx processing into NAPI context

This patch moves the tx cleanup processing out of the MSI-X interrupt
processing and gives it it's own napi routine.  This allows the driver to
process TX cleanup in a polling context instead of in an interrupt context
which prevents TX from starving RX.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: move v_idx into q_vector and use as index only
Alexander Duyck [Thu, 4 Jun 2009 16:00:09 +0000]
ixgbe: move v_idx into q_vector and use as index only

The v_idx value was being used as both a bitmask and an index.  This change
makes it so that the q_vector contains the index and allows for much of the
code to be simplified since disabling a q_vector involves only clearing one
bit in the interrupt bitmask.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: use rx_buffer_info->dma instead of nr_frags to determine skb unmap
Alexander Duyck [Thu, 4 Jun 2009 15:59:49 +0000]
ixgbe: use rx_buffer_info->dma instead of nr_frags to determine skb unmap

This patch changes the driver so that it uses rx_buffer_info->dma to
determine if it needs to unmap the page instead of sh_info->nr_frags.  This
helps to prevent a cache line miss when receiving small packets as the
rx_buffer_info data should already be in the cache.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: ethtool support to change advertised link modes of 82599 adapters
Mallikarjuna R Chilakala [Thu, 4 Jun 2009 11:11:34 +0000]
ixgbe: ethtool support to change advertised link modes of 82599 adapters

Add ethtool support to change advertised link modes/autoneg settings of
82599 multispeed fiber adapters.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Fix 82599 adapter link flickering issues
Mallikarjuna R Chilakala [Thu, 4 Jun 2009 11:11:13 +0000]
ixgbe: Fix 82599 adapter link flickering issues

Fix autoneg restart issues in flow control path which might create
endless link flickering due to known timing issues with 82599
adapters.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakakla@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Harden the 82599 multispeed fiber autotry mechanism
Peter P Waskiewicz Jr [Thu, 4 Jun 2009 11:10:53 +0000]
ixgbe: Harden the 82599 multispeed fiber autotry mechanism

82599 supports multispeed fiber optical modules (10Gbps/1Gbps).  Some
scenarios can cause the autotry mechanism to not negotiate link properly.
What needs to happen is the driver must flap the Tx laser to induce an Rx
Loss of Signal on the link partner.  This will restart the autotry
mechanism to get link into a known state.  The software definable pin (SDP)
3 on the 0x10fb NIC is wired to cause a Tx LOS event, which triggers the
Rx LOS we require.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Add ethtool offline test support
Peter P Waskiewicz Jr [Thu, 4 Jun 2009 11:10:35 +0000]
ixgbe: Add ethtool offline test support

This patch adds support for the ethtool internal test engine.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Change the 82599 PHY DSP restart logic
Peter P Waskiewicz Jr [Thu, 4 Jun 2009 11:10:17 +0000]
ixgbe: Change the 82599 PHY DSP restart logic

When reprogramming the 82599 analog PHY to either SFI optical or Direct
Attach Twinax, we need to restart the DSP in the PHY.  The current method
can cause contention with our FW which is managing PHY state, and will
cause unexpected link flaps.  This patch fixes the DSP restart by issuing
an AN_RESTART in the MAC, which will properly propagate the DSP restart to
the PHY.  This ensures we don't collide with the FW.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Enable ACPI WoL capabilities for 82599
Peter P Waskiewicz Jr [Thu, 4 Jun 2009 11:09:58 +0000]
ixgbe: Enable ACPI WoL capabilities for 82599

The 82599 KX4 device defaults to legacy power management, or APME.  This
puts the device into ACPI mode, which allows more robust WoL setups to
work properly.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agocfg80211: errno.h: define ERFKILL
Alexander Beregalov [Sun, 7 Jun 2009 12:01:00 +0000]
cfg80211: errno.h: define ERFKILL

Commit 1f87f7d3 (cfg80211: add rfkill support) added ERFKILL
to asm-generic/errno.h, but alpha, mips, parisc and sparc use
their own numbering scheme and do not include asm-generic/errno.h.
We need to add definition of ERFKILL for them.

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Sun, 7 Jun 2009 11:24:21 +0000]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6

10 years agoremoval of forcedeth device ids
Ayaz Abdulla [Sun, 7 Jun 2009 10:54:37 +0000]
removal of forcedeth device ids

This patch removes the forcedeth device ids from pci_ids.h

The forcedeth driver uses the device id constants directly in its source
file.

[ Need to keep PCI_DEVICE_ID_NVIDIA_NVENET_15 in order to keep
  drivers/pci/quirks.c building -DaveM ]

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoforcedeth: addition of new mcp89 device id
Ayaz Abdulla [Wed, 3 Jun 2009 15:05:35 +0000]
forcedeth: addition of new mcp89 device id

This patch adds a new device id for mcp89 chipset.

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoforcedeth: remove device id macros
Ayaz Abdulla [Wed, 3 Jun 2009 15:05:17 +0000]
forcedeth: remove device id macros

This patch removes the device id macros and instead uses the constants
directly.

The areas in which logic expressions where using the macros now instead
use feature/workaround flags.

No new functionality has been introduced in this patch, only clean up of
flags and macros.

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agowimax: depend on rfkill properly
Johannes Berg [Thu, 4 Jun 2009 06:22:25 +0000]
wimax: depend on rfkill properly

My mistake, I should have added that when cleaning up
rfkill and changing wimax.

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: remove deprecated code
Christian Lamparter [Wed, 3 Jun 2009 20:24:48 +0000]
ar9170: remove deprecated code

This patch removes code (deprecated by "cfg80211: add rfkill support" )

main.c: In function 'ar9170_op_config':
main.c:1306: warning: '__IEEE80211_CONF_CHANGE_RADIO_ENABLED'
is deprecated (declared at include/net/mac80211.h:551)

and a useless device state.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwlwifi: fix comment describing disable_11n
Reinette Chatre [Wed, 3 Jun 2009 18:44:12 +0000]
iwlwifi: fix comment describing disable_11n

Fixing a comment in the code describing this module parameter.
The description printed when user runs "modinfo" is correct.

Reported-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwlwifi: add value and range define for link quality command
Wey-Yi Guy [Wed, 3 Jun 2009 18:44:11 +0000]
iwlwifi: add value and range define for link quality command

Instead of hardcoding the link quality parameters inside the functions,
adding #define in iwl-commands.h to shared by different functions.
Also include the valid range for number of link quality parameters.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwlagn: delay ict interrupt.
Mohamed Abbas [Wed, 3 Jun 2009 18:44:10 +0000]
iwlagn: delay ict interrupt.

Wait until ucode is loaded and driver receive ALIVE_REPLY then switch
 to ICT interrupt. This ensures we receive all interrupts indicating
 successful ucode load.

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwl3945/iwlwifi: fix led bug when SW rfkill
Abhijeet Kolekar [Wed, 3 Jun 2009 18:44:09 +0000]
iwl3945/iwlwifi: fix led bug when SW rfkill

Patch fixes the bug at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1903

when SW rfkill is invoked by 'iwconfig txpower off',
the existing connection disassociates and led off command is sent
to the device which returns error as rfkill is 'true'.

Patch fixes this by just avoiding sending the led off/on command when
disassociated. The main purpose of the led_disassociate callback
is to start or stop the blinking.
There are three states in led
1) Always on when radio is on
2) Always off when radio is off
3) blink when associated and if there is some traffic.

In this callback 'allow_blinking' needs to be set false
when associated, as LED will be always on.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwl3945: port allow skb allocation in tasklet patch
Abhijeet Kolekar [Wed, 3 Jun 2009 18:44:08 +0000]
iwl3945: port allow skb allocation in tasklet patch

Port "iwlcore: Allow skb allocation from tasklet." to 3945

If RX queue becomes empty then we need to restock the queue from
tasklet to prevent ucode from starving. A caller to iwl_rx_allocate
will decide if allocated buffer should come from GFP_ATOMIC or
GFP_KERNEL.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwlwifi: unify station management
Tomas Winkler [Wed, 3 Jun 2009 18:44:07 +0000]
iwlwifi: unify station management

This patch unifies 3945 and AGN station management
It also removes useless struct iwl_station_mgmt ops
and cleanups a bit the interface

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoTI DaVinci EMAC: Remove print_mac, DECLARE_MAC_BUF
Chaithrika U S [Thu, 4 Jun 2009 04:54:29 +0000]
TI DaVinci EMAC: Remove print_mac, DECLARE_MAC_BUF

Use printk format specifier for MAC address.
Remove DECALRE_MAC_BUF and print_mac() usage in the driver.

Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agotun: Only wake up writers
Herbert Xu [Thu, 4 Jun 2009 04:45:55 +0000]
tun: Only wake up writers

When I added socket accounting to tun I inadvertently introduced
spurious wake-up events that kills qemu performance.  The problem
occurs when qemu polls on the tun fd for read, and then transmits
packets.  For each packet transmitted, we will wake up qemu even
if it only cares about read events.

Now this affects all sockets, but it is only a new problem for
tun.  So this patch tries to fix it for tun first and we can then
look at the problem in general.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoMerge branch 'net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vxy/lksctp-dev
David S. Miller [Thu, 4 Jun 2009 04:43:52 +0000]
Merge branch 'net-next' of git://git./linux/kernel/git/vxy/lksctp-dev

10 years agoipv4: remove ip_mc_drop_socket() declaration from af_inet.c.
Rami Rosen [Thu, 4 Jun 2009 04:43:26 +0000]
ipv4: remove ip_mc_drop_socket() declaration from af_inet.c.

ip_mc_drop_socket() method is declared in linux/igmp.h, which
is included anyhow in af_inet.c. So there is no need for this declaration.
This patch removes it from af_inet.c.

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agogso: Stop fraglists from escaping
Herbert Xu [Thu, 4 Jun 2009 04:20:51 +0000]
gso: Stop fraglists from escaping

As it stands skb fraglists can get past the check in dev_queue_xmit
if the skb is marked as GSO.  In particular, if the packet doesn't
have the proper checksums for GSO, but can otherwise be handled by
the underlying device, we will not perform the fraglist check on it
at all.

If the underlying device cannot handle fraglists, then this will
break.

The fix is as simple as moving the fraglist check from the device
check into skb_gso_ok.

This has caused crashes with Xen when used together with GRO which
can generate GSO packets with fraglists.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agocxgb3: minor aq100x phy fixes
Divy Le Ray [Wed, 3 Jun 2009 06:19:15 +0000]
cxgb3: minor aq100x phy fixes

Use generic MDIO generic values.
Based on Ben Hutchings'review comments.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agocxgb3: Update FW to 7.4.0
Divy Le Ray [Wed, 3 Jun 2009 13:38:59 +0000]
cxgb3: Update FW to 7.4.0

Update FW to 7.4.
Bump up driver revision.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agocfg80211: fix Kconfig for users of cfg80211
Johannes Berg [Wed, 3 Jun 2009 16:30:31 +0000]
cfg80211: fix Kconfig for users of cfg80211

 * iwm doesn't depend on cfg80211 or wireless extensions
 * rndis wlan selects cfg80211 - needs to depend
 * mac80211 selects cfg80211 - needs to depend

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agorfkill: document /dev/rfkill
Johannes Berg [Wed, 3 Jun 2009 08:17:59 +0000]
rfkill: document /dev/rfkill

Add some blurb about /dev/rfkill to the documentation and
fix the "transmiter" spelling error.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agorfkill: always init poll delayed work
Johannes Berg [Wed, 3 Jun 2009 07:55:29 +0000]
rfkill: always init poll delayed work

The rfkill core didn't initialise the poll delayed work
because it assumed that polling was always done by specifying
the poll function. cfg80211, however, would like to start
polling only later, which is a valid use case and easy to
support, so change rfkill to always initialise the poll
delayed work and thus allow starting polling by calling the
rfkill_resume_polling() function after registration.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath5k: disable beacon interrupt when interface is down
Bob Copeland [Wed, 3 Jun 2009 03:03:06 +0000]
ath5k: disable beacon interrupt when interface is down

When we remove the active interface, there's no need to continue
sending beacons; doing so would cause a null pointer deref in
ieee80211_beacon_get().  Disable the interrupt in remove_interface
and add a WARN_ON(!vif) in case there are other instances lurking.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: removed unused variable in ieee80211_tx()
Luis R. Rodriguez [Tue, 2 Jun 2009 22:43:25 +0000]
mac80211: removed unused variable in ieee80211_tx()

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: extend sta kdoc - explain when they are added
Luis R. Rodriguez [Tue, 2 Jun 2009 22:38:14 +0000]
mac80211: extend sta kdoc - explain when they are added

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agocfg80211: make ieee80211_get_mesh_hdrlen() static
Luis R. Rodriguez [Tue, 2 Jun 2009 20:31:10 +0000]
cfg80211: make ieee80211_get_mesh_hdrlen() static

Fixes spares warning:
net/wireless/util.c:261:5: warning:
symbol 'ieee80211_get_mesh_hdrlen' was not declared. Should it be static?

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath: make regulatory parsing more verbose on debug
Luis R. Rodriguez [Tue, 2 Jun 2009 20:30:56 +0000]
ath: make regulatory parsing more verbose on debug

This should help when reviewing issues regarding regulatory
domain on ath5k/ath9k/ar9170.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: Fix write callback of 'debug' which configures debug mask
Vasanthakumar Thiagarajan [Tue, 2 Jun 2009 13:58:55 +0000]
ath9k: Fix write callback of 'debug' which configures debug mask

Handle error condition on copy_from_user() properly and
make sure a NUL terminated char[] is sent to strict_strtoul()
for proper conversion.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwm: port to new cfg80211 rfkill
Johannes Berg [Tue, 2 Jun 2009 11:01:42 +0000]
iwm: port to new cfg80211 rfkill

Which means removing all rfkill code since it only does
soft-kill which cfg80211 will now handle in exactly the
same way the driver did.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agocfg80211: add rfkill support
Johannes Berg [Tue, 2 Jun 2009 11:01:41 +0000]
cfg80211: add rfkill support

To be easier on drivers and users, have cfg80211 register an
rfkill structure that drivers can access. When soft-killed,
simply take down all interfaces; when hard-killed the driver
needs to notify us and we will take down the interfaces
after the fact. While rfkilled, interfaces cannot be set UP.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agorfkill: add function to query state
Johannes Berg [Tue, 2 Jun 2009 11:01:40 +0000]
rfkill: add function to query state

Sometimes it is necessary to know how the state is,
and it is easier to query rfkill than keep track of
it somewhere else, so add a function for that. This
could later be expanded to return hard/soft block,
but so far that isn't necessary.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agocfg80211: move txpower wext from mac80211
Johannes Berg [Tue, 2 Jun 2009 11:01:39 +0000]
cfg80211: move txpower wext from mac80211

This patch introduces new cfg80211 API to set the TX power
via cfg80211, puts the wext code into cfg80211 and updates
mac80211 to use all that. The -ENETDOWN bits are a hack but
will go away soon.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agorfkill: create useful userspace interface
Johannes Berg [Tue, 2 Jun 2009 11:01:38 +0000]
rfkill: create useful userspace interface

The new code added by this patch will make rfkill create
a misc character device /dev/rfkill that userspace can use
to control rfkill soft blocks and get status of devices as
well as events when the status changes.

Using it is very simple -- when you open it you can read
a number of times to get the initial state, and every
further read blocks (you can poll) on getting the next
event from the kernel. The same structure you read is
also used when writing to it to change the soft block of
a given device, all devices of a given type, or all
devices.

This also makes CONFIG_RFKILL_INPUT selectable again in
order to be able to test without it present since its
functionality can now be replaced by userspace entirely
and distros and users may not want the input part of
rfkill interfering with their userspace code. We will
also write a userspace daemon to handle all that and
consequently add the input code to the feature removal
schedule.

In order to have rfkilld support both kernels with and
without CONFIG_RFKILL_INPUT (or new kernels after its
eventual removal) we also add an ioctl (that only exists
if rfkill-input is present) to disable rfkill-input.
It is not very efficient, but at least gives the correct
behaviour in all cases.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agorfkill: rewrite
Johannes Berg [Tue, 2 Jun 2009 11:01:37 +0000]
rfkill: rewrite

This patch completely rewrites the rfkill core to address
the following deficiencies:

 * all rfkill drivers need to implement polling where necessary
   rather than having one central implementation

 * updating the rfkill state cannot be done from arbitrary
   contexts, forcing drivers to use schedule_work and requiring
   lots of code

 * rfkill drivers need to keep track of soft/hard blocked
   internally -- the core should do this

 * the rfkill API has many unexpected quirks, for example being
   asymmetric wrt. alloc/free and register/unregister

 * rfkill can call back into a driver from within a function the
   driver called -- this is prone to deadlocks and generally
   should be avoided

 * rfkill-input pointlessly is a separate module

 * drivers need to #ifdef rfkill functions (unless they want to
   depend on or select RFKILL) -- rfkill should provide inlines
   that do nothing if it isn't compiled in

 * the rfkill structure is not opaque -- drivers need to initialise
   it correctly (lots of sanity checking code required) -- instead
   force drivers to pass the right variables to rfkill_alloc()

 * the documentation is hard to read because it always assumes the
   reader is completely clueless and contains way TOO MANY CAPS

 * the rfkill code needlessly uses a lot of locks and atomic
   operations in locked sections

 * fix LED trigger to actually change the LED when the radio state
   changes -- this wasn't done before

Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> [thinkpad]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agonl80211: use GFP_ATOMIC for michael mic failure message
Bob Copeland [Tue, 2 Jun 2009 04:05:04 +0000]
nl80211: use GFP_ATOMIC for michael mic failure message

nl80211_michael_mic_failure can be called in atomic context but
does a GFP_KERNEL allocation.  Fixes the error below:

[  126.793225] BUG: sleeping function called from invalid context at mm/slab.c:3055
[  126.793234] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper
[  126.793241] 2 locks held by swapper/0:
[  126.793246]  #0:  (&sc->rxbuflock){+.-.+.}, at: [<f94e1b46>] ath5k_tasklet_rx+0x34/0x55e [ath5k]
[  126.793294]  #1:  (rcu_read_lock){.+.+.+}, at: [<f92872f3>] __ieee80211_rx+0x7e/0x563 [mac80211]
[  126.793342] Pid: 0, comm: swapper Not tainted 2.6.30-rc7-wl #124
[  126.793347] Call Trace:
[  126.793361]  [<c014499d>] ? __debug_show_held_locks+0x1e/0x20
[  126.793380]  [<c011e9a3>] __might_sleep+0x100/0x107
[  126.793386]  [<c018ea99>] kmem_cache_alloc+0x35/0x170
[  126.793393]  [<c02e8bb1>] ? __alloc_skb+0x2e/0x117
[  126.793397]  [<c014517d>] ? mark_held_locks+0x43/0x5b
[  126.793402]  [<c02e8bb1>] __alloc_skb+0x2e/0x117
[  126.793419]  [<f851a836>] nl80211_michael_mic_failure+0x2a/0x1fa [cfg80211]
[  126.793425]  [<c01453b8>] ? trace_hardirqs_on_caller+0xf6/0x130
[  126.793430]  [<c01453fd>] ? trace_hardirqs_on+0xb/0xd
[  126.793444]  [<f851b2b8>] cfg80211_michael_mic_failure+0x30/0x38 [cfg80211]
[  126.793463]  [<f928bf69>] mac80211_ev_michael_mic_failure+0xfd/0x108 [mac80211]
[  126.793480]  [<f9279fbd>] ieee80211_rx_h_michael_mic_verify+0xd4/0x117 [mac80211]
[  126.793499]  [<f9285ef3>] ieee80211_invoke_rx_handlers+0xdde/0x1963 [mac80211]
[  126.793505]  [<c0107152>] ? sched_clock+0x3f/0x64
[  126.793511]  [<c0107152>] ? sched_clock+0x3f/0x64
[  126.793516]  [<c01445d7>] ? trace_hardirqs_off+0xb/0xd
[  126.793521]  [<c0107152>] ? sched_clock+0x3f/0x64
[  126.793526]  [<c0146454>] ? __lock_acquire+0x62c/0x1271
[  126.793545]  [<f9286fbb>] __ieee80211_rx_handle_packet+0x543/0x564 [mac80211]
[  126.793564]  [<f9287757>] __ieee80211_rx+0x4e2/0x563 [mac80211]
[  126.793577]  [<f94e1ff6>] ath5k_tasklet_rx+0x4e4/0x55e [ath5k]
[  126.793583]  [<c0102b54>] ? restore_nocheck_notrace+0x0/0xe
[  126.793589]  [<c0129aa2>] tasklet_action+0x92/0xe5
[  126.793594]  [<c0129f22>] __do_softirq+0xb1/0x182
[  126.793599]  [<c012a023>] do_softirq+0x30/0x48
[  126.793603]  [<c012a19b>] irq_exit+0x3d/0x74
[  126.793609]  [<c0358016>] do_IRQ+0x76/0x8c
[  126.793613]  [<c010312e>] common_interrupt+0x2e/0x34
[  126.793618]  [<c014007b>] ? timer_list_show+0x277/0x939
[  126.793630]  [<f88eb321>] ? acpi_idle_enter_bm+0x266/0x291 [processor]
[  126.793636]  [<c02d00f6>] cpuidle_idle_call+0x6a/0x9c
[  126.793640]  [<c0101cc8>] cpu_idle+0x53/0x87
[  126.793645]  [<c0344510>] rest_init+0x6c/0x6e
[  126.793651]  [<c04dd74d>] start_kernel+0x286/0x28b
[  126.793656]  [<c04dd037>] __init_begin+0x37/0x3c

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agolibertas: improve function init/shutdown handling for SD8688
Bing Zhao [Tue, 2 Jun 2009 01:04:36 +0000]
libertas: improve function init/shutdown handling for SD8688

This patch is to incorporate Dan Williams' comments for commit:
"libertas: implement function init/shutdown commands for SD8688"

1. remove fn_init_required and fn_shutdown_required variables from
lbs_private structure. If required, __lbs_cmd() will be called
directly to send function init/shutdown command for SD8688 in
if_sdio_probe() or if_sdio_remove() callback.

2. add global variable "user_rmmod" to distinguish between the module
removal case and the card removal case. This flag will be checked in
if_sdio_remove() against SD8688 card to determine whether or not the
function shutdown command needs to be sent.

3. remove "card" from if_sdio_model structure as it cannot store
card pointers for multiple cards. Besides, it's no longer needed
to store the "card" pointer with changes #1 & #2 above.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agowireless/p54: prepare for FIRMWARE_NAME_MAX removal
Samuel Ortiz [Wed, 27 May 2009 08:12:51 +0000]
wireless/p54: prepare for FIRMWARE_NAME_MAX removal

We're going to remove the FIRMWARE_NAME_MAX definition in order to avoid any
firmware name length restriction.
This patch gets rid of the statically allocated p54usb firmware string, and
replaces them with const char pointers.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwmc3200wifi: shrink calibration lmac name
Samuel Ortiz [Tue, 2 Jun 2009 07:52:20 +0000]
iwmc3200wifi: shrink calibration lmac name

iwmc3200wifi: trim down calibration firmware name

The patch trims down iwmc3200wifi calibration firmware name from
iwmc3200wifi-lmac-calib-sdio.bin to iwmc3200wifi-calib-sdio.bin. We can
shorten the firmware name because all calibration is done by LMAC.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: cancel led worker properly on exit
Christian Lamparter [Mon, 1 Jun 2009 20:49:25 +0000]
ar9170: cancel led worker properly on exit

"[PATCH 3/4 v2] ar9170: fix LED power state handling" revealed
a bug which can cause a ugly crash.

The delayed worker is canceled before the LED class functions are
unregistered... So, if something manages to update the LEDs
while unregister routine is running the timer could fire _after_ the
module has been unloaded.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170usb: more minor fixes
Christian Lamparter [Thu, 28 May 2009 15:04:27 +0000]
ar9170usb: more minor fixes

This patch contains a few more mostly random fixes for the USB front-end.

1. handle irq command response, instead of printing it to the console.

2. remove fixed FIXME.
    (real fix: "ar9170usb: reset device on resume". )

3. some more one-liner.
- get rid of a useless "return;"
- add a few branch prediction hints in hot-paths
etc.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: fix lockdep warning on hibernate
Christian Lamparter [Sat, 23 May 2009 18:31:21 +0000]
ar9170: fix lockdep warning on hibernate

This patch takes care of Johannes' deadlock report by moving the
mutex_lock right after cancel_work_sync in ar9170_op_stop.

Besides, the janitor does not need to hold the mutex anymore,
so this extra lines can be removed as well.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: fix LED power state handling
Christian Lamparter [Mon, 25 May 2009 19:51:19 +0000]
ar9170: fix LED power state handling

This patch fixes a minor visual bug in the led code, which
left the LED in the wrong power state when it was toggled
in a _unexpected_ way (e.g: enabling the LED twice).

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: kill duplicated HT feature flag
Christian Lamparter [Sat, 23 May 2009 18:28:38 +0000]
ar9170: kill duplicated HT feature flag

This patch removes a redundant flag.

.cap = IEEE80211_HT_CAP_MAX_AMSDU | \
> IEEE80211_HT_CAP_SM_PS | \ <
[...] \
> IEEE80211_HT_CAP_SM_PS, \ <
.ampdu_factor   = 3, \

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: use bitop macros for tx filter flags
Christian Lamparter [Sat, 23 May 2009 18:28:21 +0000]
ar9170: use bitop macros for tx filter flags

This patch fixes a bug in configure_filter's (sub-)routines.
We never really cleared the flags once we updated the hardware state,
so we wasted our resources by applying already active settings.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: introduce functions for MAC programming
Christian Lamparter [Mon, 1 Jun 2009 19:42:01 +0000]
ar9170: introduce functions for MAC programming

This patch introduces 3 new function which are used to update
the MAC state, whenever needed... e.g: after a band switch.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: 40mhz fixes
Christian Lamparter [Mon, 1 Jun 2009 19:41:50 +0000]
ar9170: 40mhz fixes

This patch replace a few constant magics which may affected
the device when operating in a 40MHz channel.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: update hardware definitions
Christian Lamparter [Mon, 1 Jun 2009 19:41:36 +0000]
ar9170: update hardware definitions

This patch only contains a few uncritical updates for the
hardware definition header.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: fix beacon plcp settings
Christian Lamparter [Mon, 1 Jun 2009 19:41:31 +0000]
ar9170: fix beacon plcp settings

This patch fixes a simple copy & paste error that affected beacon
transmission in 802.11a mode.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211_hwsim: remove deprecated radio_enabled
Johannes Berg [Mon, 1 Jun 2009 12:29:52 +0000]
mac80211_hwsim: remove deprecated radio_enabled

This removes the use of the deprecated radio_enabled setting
and code associated with that.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agocfg80211: fix for duplicate userspace replies
Luis R. Rodriguez [Sun, 31 May 2009 22:24:34 +0000]
cfg80211: fix for duplicate userspace replies

This fixes an incorrect assumption (BUG_ON) made in
cfg80211 when handling country IE regulatory requests.
The assumption was that we won't try to call_crda()
twice for the same event and therefore we will not
recieve two replies through nl80211 for the regulatory
request. As it turns out it is true we don't call_crda()
twice for the same event, however, kobject_uevent_env()
*might* send the udev event twice and/or userspace can
simply process the udev event twice. We remove the BUG_ON()
and simply ignore the duplicate request.

For details refer to this thread:

http://marc.info/?l=linux-wireless&m=124149987921337&w=2

Cc: stable@kernel.org
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agonet: introduce pre-up netdev notifier
Johannes Berg [Fri, 29 May 2009 23:39:53 +0000]
net: introduce pre-up netdev notifier

NETDEV_UP is called after the device is set UP, but sometimes
it is useful to be able to veto the device UP. Introduce a
new NETDEV_PRE_UP notifier that can be used for exactly this.
The first use case will be cfg80211 denying interfaces to be
set UP if the device is known to be rfkill'ed.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: add AVM FRITZ devices
Luis R. Rodriguez [Thu, 28 May 2009 21:36:05 +0000]
ar9170: add AVM FRITZ devices

This adds:

USB 0x057C:0x8401       AVM FRITZ!WLAN USB Stick N
USB 0x057C:0x8402       AVM FRITZ!WLAN USB Stick N 2.4

These devices require the 1-stage firmware, if not present we
don't continue.

Cc: Peter Grabienski <Peter.Grabienski@Atheros.com>
Cc: Stephen Chen <Stephen.Chen@Atheros.com>
Cc: Michael Fortin <Michael.Fortin@Atheros.com>
Cc: Johnny Cheng <Johnny.Cheng@Atheros.com>
Cc: Yuan-Gu Wei <Yuan-Gu.Wei@atheros.com>
Cc: Joerg Albert <jal2@gmx.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoar9170: add support for 1-stage firmware
Luis R. Rodriguez [Thu, 28 May 2009 21:36:04 +0000]
ar9170: add support for 1-stage firmware

You can get the stage 1 firmware from here:

http://www.kernel.org/pub/linux/kernel/people/mcgrof/firmware/ar9170/ar9170.fw

md5sum: 34feec4ec0eae3bb92c7c1ea2dfb4530
sha1sum: 6e5250498b815c2940d97242de31e054ae44e079

Its license:

http://www.kernel.org/pub/linux/kernel/people/mcgrof/firmware/ar9170/LICENSE

This is a new firmware, tested with WNDA3100.

Cc: Peter Grabienski <Peter.Grabienski@Atheros.com>
Cc: Stephen Chen <Stephen.Chen@Atheros.com>
Cc: Michael Fortin <Michael.Fortin@Atheros.com>
Cc: Johnny Cheng <Johnny.Cheng@Atheros.com>
Cc: Yuan-Gu Wei <Yuan-Gu.Wei@atheros.com>
Cc: Joerg Albert <jal2@gmx.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: Add sanity check for beacon_int in adhoc/mesh case
Jouni Malinen [Thu, 28 May 2009 16:25:28 +0000]
ath9k: Add sanity check for beacon_int in adhoc/mesh case

It looks like mac80211 can request the driver to start beaconing with
a beacon interval of zero in some cases (at least for mesh point). This
does not sound correct and something may need to be fixed in
mac80211. However, taken into account the unpleasantness of getting
stuck in an infinite busy loop with rtnl_lock held, let's add a quick
workaround in the driver to avoid the worst symptom while someone more
familiar with the mesh implementation can figure out what should be done
with mac80211 as far as beacon interval configuration is concerned.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath5k: remove conf->beacon_int usage
Bob Copeland [Thu, 28 May 2009 14:27:37 +0000]
ath5k: remove conf->beacon_int usage

ieee80211_conf->beacon_int was deprecated and removed in a cleanup
patch, however it was accidentally added back to ath5k in the change
"ath5k: Allow user/driver to set txpower."  Remove it once more,
fixing the following warning:

[13091.968902] WARNING: at drivers/net/wireless/ath/ath5k/base.c:2167 warn_slowpath_null+0x15/0x1a()
[13091.968906] Hardware name: MacBook1,1
[13091.968909] Modules linked in: usb_storage fuse i915 drm af_packet acpi_cpufreq binfmt_misc dm_mirror dm_region_hash dm_log dm_multipath dm_mod snd_hda_codec_idt snd_hda_intel snd_hda_codec snd_seq_dummy hid_apple arc4 ecb snd_seq_oss snd_seq_midi_event usbhid snd_seq ath5k mac80211 appletouch snd_seq_device snd_pcm_oss snd_mixer_oss sky2 snd_pcm ath processor cfg80211 snd_timer sg ohci1394 snd uhci_hcd bitrev ieee1394 joydev ehci_hcd crc32 snd_page_alloc button ac thermal battery sr_mod applesmc cdrom evdev input_polldev unix [last unloaded: microcode]
[13091.968985] Pid: 2132, comm: phy0 Tainted: G        W  2.6.30-rc5-wl #118
[13091.968988] Call Trace:
[13091.968994]  [<c0125884>] warn_slowpath_fmt+0x77/0xa6
[13091.969003]  [<c03557d8>] ? _spin_unlock+0x2c/0x41
[13091.969008]  [<c0355a56>] ? _spin_lock_irqsave+0x15/0x69
[13091.969012]  [<c0355783>] ? _spin_unlock_irqrestore+0x34/0x5d
[13091.969019]  [<c01445bb>] ? trace_hardirqs_off+0xb/0xd
[13091.969024]  [<c0355783>] ? _spin_unlock_irqrestore+0x34/0x5d
[13091.969029]  [<c01445bb>] ? trace_hardirqs_off+0xb/0xd
[13091.969034]  [<c0355783>] ? _spin_unlock_irqrestore+0x34/0x5d
[13091.969039]  [<c01258c8>] warn_slowpath_null+0x15/0x1a
[13091.969054]  [<f965846d>] ath5k_beacon_update_timers+0x44/0x27f [ath5k]
[13091.969059]  [<c0126370>] ? vprintk+0x2dd/0x312
[13091.969063]  [<c0125e50>] ? release_console_sem+0x1a6/0x1d3
[13091.969076]  [<f96586c5>] ath5k_reset_tsf+0x1d/0x2c [ath5k]
[13091.969095]  [<f93f4426>] __ieee80211_sta_join_ibss+0x35/0x3aa [mac80211]
[13091.969102]  [<c0252793>] ? extract_entropy+0x47/0x8a
[13091.969121]  [<f93f4b21>] ieee80211_sta_find_ibss+0x2de/0x32f [mac80211]
[13091.969126]  [<c035422c>] ? mutex_lock_nested+0x28b/0x2a5
[13091.969145]  [<f93f4b8e>] ? ieee80211_ibss_notify_scan_completed+0x1c/0x6f [mac80211]
[13091.969164]  [<f93f4bc9>] ieee80211_ibss_notify_scan_completed+0x57/0x6f [mac80211]
[13091.969182]  [<f93f26da>] ieee80211_scan_completed+0x31a/0x33f [mac80211]
[13091.969201]  [<f93f27ca>] ieee80211_scan_work+0xcb/0x18b [mac80211]
[13091.969207]  [<c0133a6a>] worker_thread+0x1b1/0x28e
[13091.969212]  [<c0133a25>] ? worker_thread+0x16c/0x28e
[13091.969230]  [<f93f26ff>] ? ieee80211_scan_work+0x0/0x18b [mac80211]
[13091.969237]  [<c013736e>] ? autoremove_wake_function+0x0/0x38
[13091.969242]  [<c01338b9>] ? worker_thread+0x0/0x28e
[13091.969246]  [<c0137031>] kthread+0x4a/0x70
[13091.971460]  [<c0136fe7>] ? kthread+0x0/0x70
[13091.971467]  [<c0103527>] kernel_thread_helper+0x7/0x10
[13091.971470] ---[ end trace 8defaa5d15c50cef ]---

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: handle -EALREADY on cfg80211 op assoc req
Luis R. Rodriguez [Thu, 28 May 2009 02:56:05 +0000]
mac80211: handle -EALREADY on cfg80211 op assoc req

When the SME requests to associate to an open AP
ieee80211_sta_set_extra_ie() can be called with zero IE
length. When this happens or when the extra IE has already
been set -EALREADY is passed down and the supplicant will
complain that the operation is already in progress and it will
not let us associate. We correct this by treating -EALREADY
from ieee80211_sta_set_extra_ie() as a success just as we do
for wext.

Cc: Shan.Palanisamy@Atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agowireless: libertas: fix unaligned accesses
Cliff Cai [Wed, 27 May 2009 18:03:09 +0000]
wireless: libertas: fix unaligned accesses

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: Add "debug" file to debugfs
Jeff Hansen [Wed, 27 May 2009 12:48:29 +0000]
ath9k: Add "debug" file to debugfs

This patch adds the debug file to the ath9k debugfs, which lets you modify
the debug_mask at runtime, without having to reload the ath9k module.

Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: Combine legacy and 11n rc statistics
Jeff Hansen [Wed, 27 May 2009 12:48:28 +0000]
ath9k: Combine legacy and 11n rc statistics

This patch combines the legacy and 11n rcstats into one, using the normal
rate table indices instead of two separate indices for each mode.  Legacy
rates also get all of the PER and retry information, now, too.

Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoath9k: Reset SC_OP_TSF_RESET flag after stuck beacon
Jeff Hansen [Wed, 27 May 2009 12:48:27 +0000]
ath9k: Reset SC_OP_TSF_RESET flag after stuck beacon

I have a TrendNet 652-BRP running OpenWRT + ath9k very well.  The only
problem is that the beacon gets stuck maybe once a day.  After
Vasanthakumar Thiagarajan's "ath9k: cleanup beacon parameters
configuration" patch, ath9k would nearly re-configure the beacons after it
detected the stuck beacon, and did a reset.  But it would fail the
SC_OP_TSF_RESET check in ath_beacon_config_ap.  This patch gets the beacon
fully reconfigured after the reset.

Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agocfg80211: disallow interfering with stations on non-AP (part 2)
Johannes Berg [Wed, 27 May 2009 08:35:29 +0000]
cfg80211: disallow interfering with stations on non-AP (part 2)

On non-AP interfaces userspace has no business interfering with
the station management, this can confuse mac80211 (and other
drivers probably wouldn't support it anyway). Allow adding and
removing stations only on AP interfaces.

(Reconcile this w/ previous version of patch posted with same
subject... -- JWL)

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: fix transposed min/max CW values
Johannes Berg [Wed, 27 May 2009 07:41:06 +0000]
mac80211: fix transposed min/max CW values

I accidentally transposed these in the patch that "fixed" the defaults,
leading to extremely low throughput because of the huge min CW.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwmc3200wifi: fix printk format
Randy Dunlap [Tue, 26 May 2009 19:17:52 +0000]
iwmc3200wifi: fix printk format

Fix printk format for size_t variable:

drivers/net/wireless/iwmc3200wifi/fw.c:75: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: ilw@linux.intel.com
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwmc3200wifi: fix fragmentation threshold setting
Samuel Ortiz [Tue, 26 May 2009 03:10:46 +0000]
iwmc3200wifi: fix fragmentation threshold setting

We were sending the fragmentation threshold value to the wrong table,
causing an LMAC assert when setting it from wext.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwlwifi: avoid build warning in iwl-core.
Rami Rosen [Sun, 24 May 2009 17:43:50 +0000]
iwlwifi: avoid build warning in iwl-core.

When building when CONFIG_IWLWIFI_DEBUG is not set, we get the following
warning:
/work/src/w/drivers/net/wireless/iwlwifi/iwl-core.c: In function ‘iwl_isr’:
/work/src/w/drivers/net/wireless/iwlwifi/iwl-core.c:1707: warning:
unused variable ‘inta_fh’

This patch avoids this warning by adding #ifdef CONFIG_IWLWIFI_DEBUG
before the declaration of inta_fh in iwl_isr() in
drivers/net/wireless/iwlwifi/iwl-core.c

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agocfg80211: use key size constants
Johannes Berg [Sun, 24 May 2009 14:57:19 +0000]
cfg80211: use key size constants

Instead of hardcoding the key length for validation, use the
constants Zhu Yi recently added and add one for AES_CMAC too.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agonl80211: bounce scan request back to userspace
Johannes Berg [Sun, 24 May 2009 14:43:15 +0000]
nl80211: bounce scan request back to userspace

When a scan finishes only the program that asked for it
knows what kind of scan it was; let's tell everybody else
about the scan parameters as well so they can evaluate
the result of the scan better. Also helps with debugging.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agocfg80211: validate AID of stations being added
Johannes Berg [Sun, 24 May 2009 14:42:30 +0000]
cfg80211: validate AID of stations being added

We have some validation code in mac80211 but said code will
force an invalid AID to 0 which isn't a valid AID either;
instead require a valid AID (1-2007) to be passed in from
userspace in cfg80211 already. Also move the code before
the race comment since it can only be executed during STA
addition and thus is not racy.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agort2x00: Remove last usage of beacon_int from ieee80211_config
Ivo van Doorn [Sat, 23 May 2009 19:09:28 +0000]
rt2x00: Remove last usage of beacon_int from ieee80211_config

This removes the last usage of beacon_int inside the iee80211_config
structure from rt2x00. The attempt is a bit hackish, and subject to
change in the future when the entire rt2x00_dev structure is
cleaned up and restructured.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agomac80211: deprecate conf.beacon_int properly
Johannes Berg [Sat, 23 May 2009 09:18:45 +0000]
mac80211: deprecate conf.beacon_int properly

Ivo has updated the driver to no longer use the change flag,
so we can remove that, but rt2x00 and ath5k still use the
actual value so let's mark it as deprecated too.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agolibertas: fix WPA adhoc network creation
Dan Williams [Sat, 23 May 2009 00:09:58 +0000]
libertas: fix WPA adhoc network creation

Oddly enough, the firmware's JOIN/START commands don't appear to have
any facility for setting custom IEs, thus the started adhoc network
doesn't advertise its WPA capability in the beacon.  Whee!

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agolibertas: convert CMD_802_11_ASSOCIATE to a direct command
Dan Williams [Sat, 23 May 2009 00:07:14 +0000]
libertas: convert CMD_802_11_ASSOCIATE to a direct command

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agolibertas: convert CMD_802_11_AUTHENTICATE to a direct command
Dan Williams [Sat, 23 May 2009 00:05:25 +0000]
libertas: convert CMD_802_11_AUTHENTICATE to a direct command

And fix up setting authentication suite for v9+ firmware too.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agolibertas: restyle Marvell & IEEE TLV structure names
Dan Williams [Sat, 23 May 2009 00:03:09 +0000]
libertas: restyle Marvell & IEEE TLV structure names

Easier to read and more conformant with kernel style.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agolibertas: simplify and clean up association/start/join setup
Dan Williams [Sat, 23 May 2009 00:01:21 +0000]
libertas: simplify and clean up association/start/join setup

Some of the parameters for association/join/start commands aren't
used (like the FH and CF IEs for IBSS, and the FH IE for BSS), so
get rid of their unions to reduce indirection.  Also clean up
structure names for kernel style.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwlwifi: fix otp access init
Reinette Chatre [Fri, 22 May 2009 21:37:55 +0000]
iwlwifi: fix otp access init

Polling function returns positive time if polling was needed to
read value. This is still success.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agoiwlwifi: fix merge error
Reinette Chatre [Fri, 22 May 2009 21:37:54 +0000]
iwlwifi: fix merge error

This hunk of code was removed in patch "iwlwifi: do not
cancel delayed work inside spin_lock_irqsave" submitted at
http://marc.info/?l=linux-wireless&m=124267503030042&w=2

This same patch in this repo does not remove this hunk.
Remove it here.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agort2x00: Add new rt2800usb USB ID's
Ivo van Doorn [Fri, 22 May 2009 19:33:21 +0000]
rt2x00: Add new rt2800usb USB ID's

new patch to add more usb_dev to rt2800usb.c .
IDs 'stolen' from the latest Ralink linux
driver(2009_0520_RT3070_Linux_STA_v2.1.1.0.tar.gz)

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

10 years agonet/libertas: make SPI interface big endian aware
Sebastian Andrzej Siewior [Fri, 22 May 2009 19:19:40 +0000]
net/libertas: make SPI interface big endian aware

The comment (which I remove) says that the translation is done SPI routines.
IMHO this can't work because the SPI driver does not know whether the incomming
bytes are part of the registers/bytes which need to be flipped or part of
packet data which has to remain untouched.
While adding le helpers I also removed spu_write_u32() which has no users.

Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>