6 years agob43: N-PHY: use more bits for offset in RSSI calibration
Rafał Miłecki [Wed, 27 Mar 2013 07:37:08 +0000]
b43: N-PHY: use more bits for offset in RSSI calibration

commit 2e1253d640eb7f8707d2591c93097c1e9f9c71d5 upstream.

When calculating "offset" for final RSSI calibration we're using numbers
bigger than s8 can hold. We have for example:
offset[j] = 232 - poll_results[j];
formula. If poll_results[j] is small enough (it usually is) we treat
number's bit as a sign bit. For example 232 - 1 becomes:
0xE8 - 0x1 = 0xE7, which is not 231 but -25.

This code was introduced in e0c9a0219a8f542e3946fe972a68aacf8c3f906c
and caused stability regression on some cards, for ex. BCM4322.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

6 years agob43: A fix for DMA transmission sequence errors
Iestyn C. Elfick [Wed, 20 Mar 2013 19:02:31 +0000]
b43: A fix for DMA transmission sequence errors

commit b251412db99ccd4495ce372fec7daee27bf06923 upstream.

Intermittently, b43 will report "Out of order TX status report on DMA ring".
When this happens, the driver must be reset before communication can resume.
The cause of the problem is believed to be an error in the closed-source
firmware; however, all versions of the firmware are affected.

This change uses the observation that the expected status is always 2 less
than the observed value, and supplies a fake status report to skip one
header/data pair.

Not all devices suffer from this problem, but it can occur several times
per second under heavy load. As each occurence kills the unmodified driver,
this patch makes if possible for the affected devices to function. The patch
logs only the first instance of the reset operation to prevent spamming
the logs.

Tested-by: Chris Vine <chris@cvine.freeserve.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agob43: N-PHY: increase initial value of "mind" in RSSI calibration
Rafał Miłecki [Tue, 19 Mar 2013 06:52:48 +0000]
b43: N-PHY: increase initial value of "mind" in RSSI calibration

commit e67dd874e60529dbd2e8232babb1e23479ba2ffa upstream.

We're using "mind" variable to find the VCM that got the best polling
results. For each VCM we calculte "currd" which is compared to the
"mind". For PHY rev3+ "currd" gets values around 14k-40k. Looking for a
value smaller than 40 makes no sense, so increase the initial value.

This fixes a regression introduced in 3.4 by commit:
e0c9a0219a8f542e3946fe972a68aacf8c3f906c
(my BCM4322 performance dropped from 18,4Mb/s to 9,26Mb/s)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agortlwifi: usb: add missing freeing of skbuff
Jussi Kivilinna [Sun, 17 Mar 2013 09:54:04 +0000]
rtlwifi: usb: add missing freeing of skbuff

commit 36ef0b473fbf43d5db23eea4616cc1d18cec245f upstream.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoHID: usbhid: quirk for Realtek Multi-card reader
Josh Boyer [Mon, 18 Mar 2013 13:45:42 +0000]
HID: usbhid: quirk for Realtek Multi-card reader

commit 3d464d9b71ef2f2b40a4bc9dcf06794fd1be9d12 upstream.

This device needs to be added to the quirks list with HID_QUIRK_NO_INIT_REPORTS,
otherwise it causes 10 seconds timeout during report initialization.

This fixes Red Hat bugzilla https://bugzilla.redhat.com/show_bug.cgi?id=806587

Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoath9k_hw: revert chainmask to user configuration after calibration
Felix Fietkau [Fri, 15 Mar 2013 13:53:31 +0000]
ath9k_hw: revert chainmask to user configuration after calibration

commit 74632d11a133b5baf6b9d622dd19d2f944d93d94 upstream.

The commit 'ath9k_hw: fix calibration issues on chainmask that don't
include chain 0' changed the hardware chainmask to the chip chainmask
for the duration of the calibration, but the revert to user
configuration in the reset path runs too early.

That causes some issues with limiting the number of antennas (including
spurious failure in hardware-generated packets).

Fix this by reverting the chainmask after the essential parts of the
calibration that need the workaround, and before NF calibration is run.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agocan: sja1000: fix define conflict on SH
Marc Kleine-Budde [Wed, 27 Mar 2013 10:36:42 +0000]
can: sja1000: fix define conflict on SH

commit f901b6bc404b67d96eca739857c097e022727b71 upstream.

Thias patch fixes a define conflict between the SH architecture and the sja1000
driver:

    drivers/net/can/sja1000/sja1000.h:59:0: warning:
        "REG_SR" redefined [enabled by default]
    arch/sh/include/asm/ptrace_32.h:25:0: note:
         this is the location of the previous definition

A SJA1000_ prefix is added to the offending sja1000 define only, to make a
minimal patch suited for stable. A later patch will add a SJA1000_ prefix to
all defines in sja1000.h.

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosysfs: handle failure path correctly for readdir()
Ming Lei [Wed, 20 Mar 2013 15:25:25 +0000]
sysfs: handle failure path correctly for readdir()

commit e5110f411d2ee35bf8d202ccca2e89c633060dca upstream.

In case of 'if (filp->f_pos ==  0 or 1)' of sysfs_readdir(),
the failure from filldir() isn't handled, and the reference counter
of the sysfs_dirent object pointed by filp->private_data will be
released without clearing filp->private_data, so use after free
bug will be triggered later.

This patch returns immeadiately under the situation for fixing the bug,
and it is reasonable to return from readdir() when filldir() fails.

Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosysfs: fix race between readdir and lseek
Ming Lei [Wed, 20 Mar 2013 15:25:24 +0000]
sysfs: fix race between readdir and lseek

commit 991f76f837bf22c5bb07261cfd86525a0a96650c upstream.

While readdir() is running, lseek() may set filp->f_pos as zero,
then may leave filp->private_data pointing to one sysfs_dirent
object without holding its reference counter, so the sysfs_dirent
object may be used after free in next readdir().

This patch holds inode->i_mutex to avoid the problem since
the lock is always held in readdir path.

Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agostaging: comedi: s626: fix continuous acquisition
Ian Abbott [Fri, 22 Mar 2013 15:16:29 +0000]
staging: comedi: s626: fix continuous acquisition

commit e4317ce877a31dbb9d96375391c1c4ad2210d637 upstream.

For the s626 driver, there is a bug in the handling of asynchronous
commands on the AI subdevice when the stop source is `TRIG_NONE`.  The
command should run continuously until cancelled, but the interrupt
handler stops the command running after the first scan.

The command set-up function `s626_ai_cmd()` contains this code:

switch (cmd->stop_src) {
case TRIG_COUNT:
/*  data arrives as one packet */
devpriv->ai_sample_count = cmd->stop_arg;
devpriv->ai_continous = 0;
break;
case TRIG_NONE:
/*  continous acquisition */
devpriv->ai_continous = 1;
devpriv->ai_sample_count = 0;
break;
}

The interrupt handler `s626_irq_handler()` contains this code:

if (!(devpriv->ai_continous))
devpriv->ai_sample_count--;
if (devpriv->ai_sample_count <= 0) {
devpriv->ai_cmd_running = 0;
/* ... */
}

So `devpriv->ai_sample_count` is only decremented for the `TRIG_COUNT`
case, but `devpriv->ai_cmd_running` is set to 0 (and the command
stopped) regardless.

Fix this in `s626_ai_cmd()` by setting `devpriv->ai_sample_count = 1`
for the `TRIG_NONE` case.  The interrupt handler will not decrement it
so it will remain greater than 0 and the check for stopping the
acquisition will fail.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoBluetooth: Add support for Dell[QCA 0cf3:817a]
Ming Lei [Mon, 18 Mar 2013 15:45:11 +0000]
Bluetooth: Add support for Dell[QCA 0cf3:817a]

commit ebaf5795ef57a70a042ea259448a465024e2821d upstream.

Add support for the AR9462 chip

T:  Bus=03 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#=  5 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=817a Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoBluetooth: Add support for Dell[QCA 0cf3:0036]
Ming Lei [Fri, 15 Mar 2013 03:00:39 +0000]
Bluetooth: Add support for Dell[QCA 0cf3:0036]

commit d66629c1325399cf080ba8b2fb086c10e5439cdd upstream.

Add support for the AR9462 chip

T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=0036 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoBluetooth: Fix not closing SCO sockets in the BT_CONNECT2 state
Vinicius Costa Gomes [Wed, 13 Mar 2013 22:46:20 +0000]
Bluetooth: Fix not closing SCO sockets in the BT_CONNECT2 state

commit eb20ff9c91ddcb2d55c1849a87d3db85af5e88a9 upstream.

With deferred setup for SCO, it is possible that userspace closes the
socket when it is in the BT_CONNECT2 state, after the Connect Request is
received but before the Accept Synchonous Connection is sent.

If this happens the following crash was observed, when the connection is
terminated:

[  +0.000003] hci_sync_conn_complete_evt: hci0 status 0x10
[  +0.000005] sco_connect_cfm: hcon ffff88003d1bd800 bdaddr 40:98:4e:32:d7:39 status 16
[  +0.000003] sco_conn_del: hcon ffff88003d1bd800 conn ffff88003cc8e300, err 110
[  +0.000015] BUG: unable to handle kernel NULL pointer dereference at 0000000000000199
[  +0.000906] IP: [<ffffffff810620dd>] __lock_acquire+0xed/0xe82
[  +0.000000] PGD 3d21f067 PUD 3d291067 PMD 0
[  +0.000000] Oops: 0002 [#1] SMP
[  +0.000000] Modules linked in: rfcomm bnep btusb bluetooth
[  +0.000000] CPU 0
[  +0.000000] Pid: 1481, comm: kworker/u:2H Not tainted 3.9.0-rc1-25019-gad82cdd #1 Bochs Bochs
[  +0.000000] RIP: 0010:[<ffffffff810620dd>]  [<ffffffff810620dd>] __lock_acquire+0xed/0xe82
[  +0.000000] RSP: 0018:ffff88003c3c19d8  EFLAGS: 00010002
[  +0.000000] RAX: 0000000000000001 RBX: 0000000000000246 RCX: 0000000000000000
[  +0.000000] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff88003d1be868
[  +0.000000] RBP: ffff88003c3c1a98 R08: 0000000000000002 R09: 0000000000000000
[  +0.000000] R10: ffff88003d1be868 R11: ffff88003e20b000 R12: 0000000000000002
[  +0.000000] R13: ffff88003aaa8000 R14: 000000000000006e R15: ffff88003d1be850
[  +0.000000] FS:  0000000000000000(0000) GS:ffff88003e200000(0000) knlGS:0000000000000000
[  +0.000000] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[  +0.000000] CR2: 0000000000000199 CR3: 000000003c1cb000 CR4: 00000000000006b0
[  +0.000000] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  +0.000000] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[  +0.000000] Process kworker/u:2H (pid: 1481, threadinfo ffff88003c3c0000, task ffff88003aaa8000)
[  +0.000000] Stack:
[  +0.000000]  ffffffff81b16342 0000000000000000 0000000000000000 ffff88003d1be868
[  +0.000000]  ffffffff00000000 00018c0c7863e367 000000003c3c1a28 ffffffff8101efbd
[  +0.000000]  0000000000000000 ffff88003e3d2400 ffff88003c3c1a38 ffffffff81007c7a
[  +0.000000] Call Trace:
[  +0.000000]  [<ffffffff8101efbd>] ? kvm_clock_read+0x34/0x3b
[  +0.000000]  [<ffffffff81007c7a>] ? paravirt_sched_clock+0x9/0xd
[  +0.000000]  [<ffffffff81007fd4>] ? sched_clock+0x9/0xb
[  +0.000000]  [<ffffffff8104fd7a>] ? sched_clock_local+0x12/0x75
[  +0.000000]  [<ffffffff810632d1>] lock_acquire+0x93/0xb1
[  +0.000000]  [<ffffffffa0022339>] ? spin_lock+0x9/0xb [bluetooth]
[  +0.000000]  [<ffffffff8105f3d8>] ? lock_release_holdtime.part.22+0x4e/0x55
[  +0.000000]  [<ffffffff814f6038>] _raw_spin_lock+0x40/0x74
[  +0.000000]  [<ffffffffa0022339>] ? spin_lock+0x9/0xb [bluetooth]
[  +0.000000]  [<ffffffff814f6936>] ? _raw_spin_unlock+0x23/0x36
[  +0.000000]  [<ffffffffa0022339>] spin_lock+0x9/0xb [bluetooth]
[  +0.000000]  [<ffffffffa00230cc>] sco_conn_del+0x76/0xbb [bluetooth]
[  +0.000000]  [<ffffffffa002391d>] sco_connect_cfm+0x2da/0x2e9 [bluetooth]
[  +0.000000]  [<ffffffffa000862a>] hci_proto_connect_cfm+0x38/0x65 [bluetooth]
[  +0.000000]  [<ffffffffa0008d30>] hci_sync_conn_complete_evt.isra.79+0x11a/0x13e [bluetooth]
[  +0.000000]  [<ffffffffa000cd96>] hci_event_packet+0x153b/0x239d [bluetooth]
[  +0.000000]  [<ffffffff814f68ff>] ? _raw_spin_unlock_irqrestore+0x48/0x5c
[  +0.000000]  [<ffffffffa00025f6>] hci_rx_work+0xf3/0x2e3 [bluetooth]
[  +0.000000]  [<ffffffff8103efed>] process_one_work+0x1dc/0x30b
[  +0.000000]  [<ffffffff8103ef83>] ? process_one_work+0x172/0x30b
[  +0.000000]  [<ffffffff8103e07f>] ? spin_lock_irq+0x9/0xb
[  +0.000000]  [<ffffffff8103fc8d>] worker_thread+0x123/0x1d2
[  +0.000000]  [<ffffffff8103fb6a>] ? manage_workers+0x240/0x240
[  +0.000000]  [<ffffffff81044211>] kthread+0x9d/0xa5
[  +0.000000]  [<ffffffff81044174>] ? __kthread_parkme+0x60/0x60
[  +0.000000]  [<ffffffff814f75bc>] ret_from_fork+0x7c/0xb0
[  +0.000000]  [<ffffffff81044174>] ? __kthread_parkme+0x60/0x60
[  +0.000000] Code: d7 44 89 8d 50 ff ff ff 4c 89 95 58 ff ff ff e8 44 fc ff ff 44 8b 8d 50 ff ff ff 48 85 c0 4c 8b 95 58 ff ff ff 0f 84 7a 04 00 00 <f0> ff 80 98 01 00 00 83 3d 25 41 a7 00 00 45 8b b5 e8 05 00 00
[  +0.000000] RIP  [<ffffffff810620dd>] __lock_acquire+0xed/0xe82
[  +0.000000]  RSP <ffff88003c3c19d8>
[  +0.000000] CR2: 0000000000000199
[  +0.000000] ---[ end trace e73cd3b52352dd34 ]---

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Tested-by: Frederic Dalleau <frederic.dalleau@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agotile: expect new initramfs name from hypervisor file system
Chris Metcalf [Fri, 29 Mar 2013 17:50:21 +0000]
tile: expect new initramfs name from hypervisor file system

commit ff7f3efb9abf986f4ecd8793a9593f7ca4d6431a upstream.

The current Tilera boot infrastructure now provides the initramfs
to Linux as a Tilera-hypervisor file named "initramfs", rather than
"initramfs.cpio.gz", as before.  (This makes it reasonable to use
other compression techniques than gzip on the file without having to
worry about the name causing confusion.)  Adapt to use the new name,
but also fall back to checking for the old name.

Cc'ing to stable so that older kernels will remain compatible with
newer Tilera boot infrastructure.

Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoSUNRPC: Add barriers to ensure read ordering in rpc_wake_up_task_queue_locked
Trond Myklebust [Mon, 25 Mar 2013 15:23:40 +0000]
SUNRPC: Add barriers to ensure read ordering in rpc_wake_up_task_queue_locked

commit 1166fde6a923c30f4351515b6a9a1efc513e7d00 upstream.

We need to be careful when testing task->tk_waitqueue in
rpc_wake_up_task_queue_locked, because it can be changed while we
are holding the queue->lock.
By adding appropriate memory barriers, we can ensure that it is safe to
test task->tk_waitqueue for equality if the RPC_TASK_QUEUED bit is set.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agokernel/signal.c: use __ARCH_HAS_SA_RESTORER instead of SA_RESTORER
Andrew Morton [Wed, 13 Mar 2013 21:59:34 +0000]
kernel/signal.c: use __ARCH_HAS_SA_RESTORER instead of SA_RESTORER

commit 522cff142d7d2f9230839c9e1f21a4d8bcc22a4a upstream.

__ARCH_HAS_SA_RESTORER is the preferred conditional for use in 3.9 and
later kernels, per Kees.

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Emese Revfy <re.emese@gmail.com>
Cc: PaX Team <pageexec@freemail.hu>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Julien Tinnes <jln@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosignal: Define __ARCH_HAS_SA_RESTORER so we know whether to clear sa_restorer
Ben Hutchings [Mon, 26 Nov 2012 03:24:19 +0000]
signal: Define __ARCH_HAS_SA_RESTORER so we know whether to clear sa_restorer

Vaguely based on upstream commit 574c4866e33d 'consolidate kernel-side
struct sigaction declarations'.

flush_signal_handlers() needs to know whether sigaction::sa_restorer
is defined, not whether SA_RESTORER is defined.  Define the
__ARCH_HAS_SA_RESTORER macro to indicate this.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoLinux 3.4.38
Greg Kroah-Hartman [Thu, 28 Mar 2013 19:12:41 +0000]
Linux 3.4.38

6 years agoasus-laptop: Do not call HWRS on init
Ben Hutchings [Thu, 29 Nov 2012 08:12:37 +0000]
asus-laptop: Do not call HWRS on init

commit cb7da022450cdaaebd33078b6b32fb7dd2aaf6db upstream.

Since commit 8871e99f89b7 ('asus-laptop: HRWS/HWRS typo'), module
initialisation is very slow on the Asus UL30A.  The HWRS method takes
about 12 seconds to run, and subsequent initialisation also seems to
be delayed.  Since we don't really need the result, don't bother
calling it on init.  Those who are curious can still get the result
through the 'infos' device attribute.

Update the comment about HWRS in show_infos().

Reported-by: ryan <draziw+deb@gmail.com>
References: http://bugs.debian.org/692436
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agort2x00: error in configurations with mesh support disabled
Felix Fietkau [Tue, 26 Feb 2013 15:09:55 +0000]
rt2x00: error in configurations with mesh support disabled

commit 6ef9e2f6d12ce9e2120916804d2ddd46b954a70b upstream.

If CONFIG_MAC80211_MESH is not set, cfg80211 will now allow advertising
interface combinations with NL80211_IFTYPE_MESH_POINT present.
Add appropriate ifdefs to avoid running into errors.

[Backported for 3.8-stable. Removed code of simultaneous AP and mesh
mode added in 4a5fc6d 3.9-rc1.]

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoexec: use -ELOOP for max recursion depth
Kees Cook [Tue, 18 Dec 2012 00:03:20 +0000]
exec: use -ELOOP for max recursion depth

commit d740269867021faf4ce38a449353d2b986c34a67 upstream.

To avoid an explosion of request_module calls on a chain of abusive
scripts, fail maximum recursion with -ELOOP instead of -ENOEXEC. As soon
as maximum recursion depth is hit, the error will fail all the way back
up the chain, aborting immediately.

This also has the side-effect of stopping the user's shell from attempting
to reexecute the top-level file as a shell script. As seen in the
dash source:

        if (cmd != path_bshell && errno == ENOEXEC) {
                *argv-- = cmd;
                *argv = cmd = path_bshell;
                goto repeat;
        }

The above logic was designed for running scripts automatically that lacked
the "#!" header, not to re-try failed recursion. On a legitimate -ENOEXEC,
things continue to behave as the shell expects.

Additionally, when tracking recursion, the binfmt handlers should not be
involved. The recursion being tracked is the depth of calls through
search_binary_handler(), so that function should be exclusively responsible
for tracking the depth.

Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: halfdog <me@halfdog.net>
Cc: P J P <ppandit@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoi915: initialize CADL in opregion
Lekensteyn [Mon, 25 Jun 2012 22:36:24 +0000]
i915: initialize CADL in opregion

commit d627b62ff8d4d36761adbcd90ff143d79c94ab22 upstream.

This is rather a hack to fix brightness hotkeys on a Clevo laptop. CADL is not
used anywhere in the driver code at the moment, but it could be used in BIOS as
is the case with the Clevo laptop.

The Clevo B7130 requires the CADL field to contain at least the ID of
the LCD device. If this field is empty, the ACPI methods that are called
on pressing brightness / display switching hotkeys will not trigger a
notification. As a result, it appears as no hotkey has been pressed.

Reference: https://bugs.freedesktop.org/show_bug.cgi?id=45452
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agotools: hv: Netlink source address validation allows DoS
Tomas Hozza [Thu, 8 Nov 2012 09:53:29 +0000]
tools: hv: Netlink source address validation allows DoS

commit 95a69adab9acfc3981c504737a2b6578e4d846ef upstream.

The source code without this patch caused hypervkvpd to exit when it processed
a spoofed Netlink packet which has been sent from an untrusted local user.
Now Netlink messages with a non-zero nl_pid source address are ignored
and a warning is printed into the syslog.

Signed-off-by: Tomas Hozza <thozza@redhat.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoudf: avoid info leak on export
Mathias Krause [Thu, 12 Jul 2012 06:46:55 +0000]
udf: avoid info leak on export

commit 0143fc5e9f6f5aad4764801015bc8d4b4a278200 upstream.

For type 0x51 the udf.parent_partref member in struct fid gets copied
uninitialized to userland. Fix this by initializing it to 0.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoisofs: avoid info leak on export
Mathias Krause [Thu, 12 Jul 2012 06:46:54 +0000]
isofs: avoid info leak on export

commit fe685aabf7c8c9f138e5ea900954d295bf229175 upstream.

For type 1 the parent_offset member in struct isofs_fid gets copied
uninitialized to userland. Fix this by initializing it to 0.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agokey: Fix resource leak
Alan Cox [Fri, 28 Sep 2012 11:20:02 +0000]
key: Fix resource leak

commit a84a921978b7d56e0e4b87ffaca6367429b4d8ff upstream.

On an error iov may still have been reallocated and need freeing

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: io_ti: fix get_icount for two port adapters
Johan Hovold [Tue, 19 Mar 2013 08:21:08 +0000]
USB: io_ti: fix get_icount for two port adapters

commit 5492bf3d5655b4954164f69c02955a7fca267611 upstream.

Add missing get_icount field to two-port driver.

The two-port driver was not updated when switching to the new icount
interface in commit 0bca1b913aff ("tty: Convert the USB drivers to the
new icount interface").

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: garmin_gps: fix memory leak on disconnect
Johan Hovold [Tue, 19 Mar 2013 08:21:07 +0000]
USB: garmin_gps: fix memory leak on disconnect

commit 618aa1068df29c37a58045fe940f9106664153fd upstream.

Remove bogus disconnect test introduced by 95bef012e ("USB: more serial
drivers writing after disconnect") which prevented queued data from
being freed on disconnect.

The possible IO it was supposed to prevent is long gone.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoudf: Fix bitmap overflow on large filesystems with small block size
Jan Kara [Tue, 5 Feb 2013 12:59:56 +0000]
udf: Fix bitmap overflow on large filesystems with small block size

commit 89b1f39eb4189de745fae554b0d614d87c8d5c63 upstream.

For large UDF filesystems with 512-byte blocks the number of necessary
bitmap blocks is larger than 2^16 so s_nr_groups in udf_bitmap overflows
(the number will overflow for filesystems larger than 128 GB with
512-byte blocks). That results in ENOSPC errors despite the filesystem
has plenty of free space.

Fix the problem by changing s_nr_groups' type to 'int'. That is enough
even for filesystems 2^32 blocks (UDF maximum) and 512-byte blocksize.

Reported-and-tested-by: v10lator@myway.de
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Jim Trigg <jtrigg@spamcop.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agonohz: Make tick_nohz_irq_exit() irq safe
Frederic Weisbecker [Wed, 20 Feb 2013 15:15:36 +0000]
nohz: Make tick_nohz_irq_exit() irq safe

commit e5ab012c3271990e8457055c25cafddc1ae8aa6b upstream.

As it stands, irq_exit() may or may not be called with
irqs disabled, depending on __ARCH_IRQ_EXIT_IRQS_DISABLED
that the arch can define.

It makes tick_nohz_irq_exit() unsafe. For example two
interrupts can race in tick_nohz_stop_sched_tick(): the inner
most one computes the expiring time on top of the timer list,
then it's interrupted right before reprogramming the
clock. The new interrupt enqueues a new timer list timer,
it reprogram the clock to take it into account and it exits.
The CPUs resumes the inner most interrupt and performs the clock
reprogramming without considering the new timer list timer.

This regression has been introduced by:
     280f06774afedf849f0b34248ed6aff57d0f6908
     ("nohz: Separate out irq exit and idle loop dyntick logic")

Let's fix it right now with the appropriate protections.

A saner long term solution will be to remove
__ARCH_IRQ_EXIT_IRQS_DISABLED and mandate that irq_exit() is called
with interrupts disabled.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Link: http://lkml.kernel.org/r/1361373336-11337-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: serial: fix interface refcounting
Johan Hovold [Tue, 19 Mar 2013 08:21:09 +0000]
USB: serial: fix interface refcounting

commit d7971051e4df825e0bc11b995e87bfe86355b8e5 upstream.

Make sure the interface is not released before our serial device.

Note that drivers are still not allowed to access the interface in
any way that may interfere with another driver that may have gotten
bound to the same interface after disconnect returns.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: cdc-acm: fix device unregistration
Johan Hovold [Tue, 19 Mar 2013 08:21:06 +0000]
USB: cdc-acm: fix device unregistration

commit cb25505fc604292c70fc02143fc102f54c8595f0 upstream.

Unregister tty device in disconnect as is required by the USB stack.

By deferring unregistration to when the last tty reference is dropped,
the parent interface device can get unregistered before the child
resulting in broken hotplug events being generated when the tty is
finally closed:

KERNEL[2290.798128] remove   /devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:3.1 (usb)
KERNEL[2290.804589] remove   /devices/pci0000:00/0000:00:1d.7/usb2/2-1 (usb)
KERNEL[2294.554799] remove   /2-1:3.1/tty/ttyACM0 (tty)

The driver must deal with tty callbacks after disconnect by checking the
disconnected flag. Specifically, further opens must be prevented and
this is already implemented.

Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: xhci: correctly enable interrupts
Hannes Reinecke [Mon, 4 Mar 2013 16:14:43 +0000]
USB: xhci: correctly enable interrupts

commit 00eed9c814cb8f281be6f0f5d8f45025dc0a97eb upstream.

xhci has its own interrupt enabling routine, which will try to
use MSI-X/MSI if present. So the usb core shouldn't try to enable
legacy interrupts; on some machines the xhci legacy IRQ setting
is invalid.

v3: Be careful to not break XHCI_BROKEN_MSI workaround (by trenn)

Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Frederik Himpe <fhimpe@vub.ac.be>
Cc: David Haerdeman <david@hardeman.nu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoUSB: xhci - fix bit definitions for IMAN register
Dmitry Torokhov [Mon, 25 Feb 2013 18:56:01 +0000]
USB: xhci - fix bit definitions for IMAN register

commit f8264340e694604863255cc0276491d17c402390 upstream.

According to XHCI specification (5.5.2.1) the IP is bit 0 and IE is bit 1
of IMAN register. Previously their definitions were reversed.

Even though there are no ill effects being observed from the swapped
definitions (because IMAN_IP is RW1C and in legacy PCI case we come in
with it already set to 1 so it was clearing itself even though we were
setting IMAN_IE instead of IMAN_IP), we should still correct the values.

This patch should be backported to kernels as old as 2.6.36, that
contain the commit 4e833c0b87a30798e67f06120cecebef6ee9644c "xhci: don't
re-enable IE constantly".

Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agox86-64: Fix the failure case in copy_user_handle_tail()
CQ Tang [Mon, 18 Mar 2013 15:02:21 +0000]
x86-64: Fix the failure case in copy_user_handle_tail()

commit 66db3feb486c01349f767b98ebb10b0c3d2d021b upstream.

The increment of "to" in copy_user_handle_tail() will have incremented
before a failure has been noted.  This causes us to skip a byte in the
failure case.

Only do the increment when assured there is no failure.

Signed-off-by: CQ Tang <cq.tang@intel.com>
Link: http://lkml.kernel.org/r/20130318150221.8439.993.stgit@phlsvslse11.ph.intel.com
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoclockevents: Don't allow dummy broadcast timers
Mark Rutland [Thu, 7 Mar 2013 15:09:24 +0000]
clockevents: Don't allow dummy broadcast timers

commit a7dc19b8652c862d5b7c4d2339bd3c428bd29c4a upstream.

Currently tick_check_broadcast_device doesn't reject clock_event_devices
with CLOCK_EVT_FEAT_DUMMY, and may select them in preference to real
hardware if they have a higher rating value. In this situation, the
dummy timer is responsible for broadcasting to itself, and the core
clockevents code may attempt to call non-existent callbacks for
programming the dummy, eventually leading to a panic.

This patch makes tick_check_broadcast_device always reject dummy timers,
preventing this problem.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoIPoIB: Fix send lockup due to missed TX completion
Mike Marciniszyn [Tue, 26 Feb 2013 15:46:27 +0000]
IPoIB: Fix send lockup due to missed TX completion

commit 1ee9e2aa7b31427303466776f455d43e5e3c9275 upstream.

Commit f0dc117abdfa ("IPoIB: Fix TX queue lockup with mixed UD/CM
traffic") attempts to solve an issue where unprocessed UD send
completions can deadlock the netdev.

The patch doesn't fully resolve the issue because if more than half
the tx_outstanding's were UD and all of the destinations are RC
reachable, arming the CQ doesn't solve the issue.

This patch uses the IB_CQ_REPORT_MISSED_EVENTS on the
ib_req_notify_cq().  If the rc is above 0, the UD send cq completion
callback is called directly to re-arm the send completion timer.

This issue is seen in very large parallel filesystem deployments
and the patch has been shown to correct the issue.

Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoext4: fix data=journal fast mount/umount hang
Theodore Ts'o [Wed, 20 Mar 2013 13:42:11 +0000]
ext4: fix data=journal fast mount/umount hang

commit 2b405bfa84063bfa35621d2d6879f52693c614b0 upstream.

In data=journal mode, if we unmount the file system before a
transaction has a chance to complete, when the journal inode is being
evicted, we can end up calling into jbd2_log_wait_commit() for the
last transaction, after the journalling machinery has been shut down.

Arguably we should adjust ext4_should_journal_data() to return FALSE
for the journal inode, but the only place it matters is
ext4_evict_inode(), and so to save a bit of CPU time, and to make the
patch much more obviously correct by inspection(tm), we'll fix it by
explicitly not trying to waiting for a journal commit when we are
evicting the journal inode, since it's guaranteed to never succeed in
this case.

This can be easily replicated via:

     mount -t ext4 -o data=journal /dev/vdb /vdb ; umount /vdb

------------[ cut here ]------------
WARNING: at /usr/projects/linux/ext4/fs/jbd2/journal.c:542 __jbd2_log_start_commit+0xba/0xcd()
Hardware name: Bochs
JBD2: bad log_start_commit: 3005630206 3005630206 0 0
Modules linked in:
Pid: 2909, comm: umount Not tainted 3.8.0-rc3 #1020
Call Trace:
 [<c015c0ef>] warn_slowpath_common+0x68/0x7d
 [<c02b7e7d>] ? __jbd2_log_start_commit+0xba/0xcd
 [<c015c177>] warn_slowpath_fmt+0x2b/0x2f
 [<c02b7e7d>] __jbd2_log_start_commit+0xba/0xcd
 [<c02b8075>] jbd2_log_start_commit+0x24/0x34
 [<c0279ed5>] ext4_evict_inode+0x71/0x2e3
 [<c021f0ec>] evict+0x94/0x135
 [<c021f9aa>] iput+0x10a/0x110
 [<c02b7836>] jbd2_journal_destroy+0x190/0x1ce
 [<c0175284>] ? bit_waitqueue+0x50/0x50
 [<c028d23f>] ext4_put_super+0x52/0x294
 [<c020efe3>] generic_shutdown_super+0x48/0xb4
 [<c020f071>] kill_block_super+0x22/0x60
 [<c020f3e0>] deactivate_locked_super+0x22/0x49
 [<c020f5d6>] deactivate_super+0x30/0x33
 [<c0222795>] mntput_no_expire+0x107/0x10c
 [<c02233a7>] sys_umount+0x2cf/0x2e0
 [<c02233ca>] sys_oldumount+0x12/0x14
 [<c08096b8>] syscall_call+0x7/0xb
---[ end trace 6a954cc790501c1f ]---
jbd2_log_wait_commit: error: j_commit_request=-1289337090, tid=0

Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agousb-storage: add unusual_devs entry for Samsung YP-Z3 mp3 player
Dmitry Artamonow [Sat, 9 Mar 2013 16:30:58 +0000]
usb-storage: add unusual_devs entry for Samsung YP-Z3 mp3 player

commit 29f86e66428ee083aec106cca1748dc63d98ce23 upstream.

Device stucks on filesystem writes, unless following quirk is passed:
  echo 04e8:5136:m > /sys/module/usb_storage/parameters/quirks

Add corresponding entry to unusual_devs.h

Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoext4: fix the wrong number of the allocated blocks in ext4_split_extent()
Zheng Liu [Mon, 11 Mar 2013 01:20:23 +0000]
ext4: fix the wrong number of the allocated blocks in ext4_split_extent()

commit 3a2256702e47f68f921dfad41b1764d05c572329 upstream.

This commit fixes a wrong return value of the number of the allocated
blocks in ext4_split_extent.  When the length of blocks we want to
allocate is greater than the length of the current extent, we return a
wrong number.  Let's see what happens in the following case when we
call ext4_split_extent().

  map: [48, 72]
  ex:  [32, 64, u]

'ex' will be split into two parts:
  ex1: [32, 47, u]
  ex2: [48, 64, w]

'map->m_len' is returned from this function, and the value is 24.  But
the real length is 16.  So it should be fixed.

Meanwhile in this commit we use right length of the allocated blocks
when get_reserved_cluster_alloc in ext4_ext_handle_uninitialized_extents
is called.

Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agojbd2: fix use after free in jbd2_journal_dirty_metadata()
Jan Kara [Mon, 11 Mar 2013 17:24:56 +0000]
jbd2: fix use after free in jbd2_journal_dirty_metadata()

commit ad56edad089b56300fd13bb9eeb7d0424d978239 upstream.

jbd2_journal_dirty_metadata() didn't get a reference to journal_head it
was working with. This is OK in most of the cases since the journal head
should be attached to a transaction but in rare occasions when we are
journalling data, __ext4_journalled_writepage() can race with
jbd2_journal_invalidatepage() stripping buffers from a page and thus
journal head can be freed under hands of jbd2_journal_dirty_metadata().

Fix the problem by getting own journal head reference in
jbd2_journal_dirty_metadata() (and also in jbd2_journal_set_triggers()
which can possibly have the same issue).

Reported-by: Zheng Liu <gnehzuil.liu@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agocifs: ignore everything in SPNEGO blob after mechTypes
Jeff Layton [Mon, 11 Mar 2013 13:52:19 +0000]
cifs: ignore everything in SPNEGO blob after mechTypes

commit f853c616883a8de966873a1dab283f1369e275a1 upstream.

We've had several reports of people attempting to mount Windows 8 shares
and getting failures with a return code of -EINVAL. The default sec=
mode changed recently to sec=ntlmssp. With that, we expect and parse a
SPNEGO blob from the server in the NEGOTIATE reply.

The current decode_negTokenInit function first parses all of the
mechTypes and then tries to parse the rest of the negTokenInit reply.
The parser however currently expects a mechListMIC or nothing to follow the
mechTypes, but Windows 8 puts a mechToken field there instead to carry
some info for the new NegoEx stuff.

In practice, we don't do anything with the fields after the mechTypes
anyway so I don't see any real benefit in continuing to parse them.
This patch just has the kernel ignore the fields after the mechTypes.
We'll probably need to reinstate some of this if we ever want to support
NegoEx.

Reported-by: Jason Burgess <jason@jacknife2.dns2go.com>
Reported-by: Yan Li <elliot.li.tech@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agodrm/radeon/benchmark: make sure bo blit copy exists before using it
Alex Deucher [Tue, 12 Mar 2013 16:53:13 +0000]
drm/radeon/benchmark: make sure bo blit copy exists before using it

commit fa8d387dc3f62062a6b4afbbb2a3438094fd8584 upstream.

Fixes a segfault on asics without a blit callback.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=62239

Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agodrm/radeon: add support for Richland APUs
Alex Deucher [Fri, 8 Mar 2013 18:44:15 +0000]
drm/radeon: add support for Richland APUs

commit e4d170633fde379f39a90f8a5e7eb619b5d1144d upstream.

Richland APUs are a new version of the Trinity APUs
with performance and power management improvements.

Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agodrm/radeon: add Richland pci ids
Alex Deucher [Fri, 8 Mar 2013 18:36:54 +0000]
drm/radeon: add Richland pci ids

commit b75bbaa038ffc426e88ea3df6c4ae11834fc3e4f upstream.

Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agotarget/iscsi: Fix mutual CHAP auth on big-endian arches
Andy Grover [Mon, 4 Mar 2013 21:52:09 +0000]
target/iscsi: Fix mutual CHAP auth on big-endian arches

commit 7ac9ad11b2a5cf77a92b58ee6b672ad2fa155eb1 upstream.

See https://bugzilla.redhat.com/show_bug.cgi?id=916290

Used a temp var since we take its address in sg_init_one.

Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
Wanpeng Li [Fri, 22 Mar 2013 22:04:40 +0000]
mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting

commit d00285884c0892bb1310df96bce6056e9ce9b9d9 upstream.

hugetlb_total_pages is used for overcommit calculations but the current
implementation considers only the default hugetlb page size (which is
either the first defined hugepage size or the one specified by
default_hugepagesz kernel boot parameter).

If the system is configured for more than one hugepage size, which is
possible since commit a137e1cc6d6e ("hugetlbfs: per mount huge page
sizes") then the overcommit estimation done by __vm_enough_memory()
(resp.  shown by meminfo_proc_show) is not precise - there is an
impression of more available/allowed memory.  This can lead to an
unexpected ENOMEM/EFAULT resp.  SIGSEGV when memory is accounted.

Testcase:
  boot: hugepagesz=1G hugepages=1
  the default overcommit ratio is 50
  before patch:

    egrep 'CommitLimit' /proc/meminfo
    CommitLimit:     55434168 kB

  after patch:

    egrep 'CommitLimit' /proc/meminfo
    CommitLimit:     54909880 kB

[akpm@linux-foundation.org: coding-style tweak]
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoKMS: fix EDID detailed timing frame rate
Torsten Duwe [Sat, 23 Mar 2013 14:39:34 +0000]
KMS: fix EDID detailed timing frame rate

commit c19b3b0f6eed552952845e4ad908dba2113d67b4 upstream.

When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed.  Consecutive (debug-) output of that mode thus yields 0 for
vsync.  This simple fix also speeds up future invocations of
drm_mode_vrefresh().

While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.

Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoKMS: fix EDID detailed timing vsync parsing
Torsten Duwe [Sat, 23 Mar 2013 14:38:22 +0000]
KMS: fix EDID detailed timing vsync parsing

commit 16dad1d743d31a104a849c8944e6b9eb479f6cd7 upstream.

EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these.  The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.

See

   http://en.wikipedia.org/wiki/EDID

and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.

Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agodrm/i915: bounds check execbuffer relocation count
Kees Cook [Tue, 12 Mar 2013 00:31:45 +0000]
drm/i915: bounds check execbuffer relocation count

commit 3118a4f652c7b12c752f3222af0447008f9b2368 upstream.

It is possible to wrap the counter used to allocate the buffer for
relocation copies. This could lead to heap writing overflows.

CVE-2013-0913

v3: collapse test, improve comment
v2: move check into validate_exec_list

Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Pinkie Pie
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomwifiex: fix potential out-of-boundary access to ibss rate table
Bing Zhao [Fri, 8 Mar 2013 04:00:16 +0000]
mwifiex: fix potential out-of-boundary access to ibss rate table

commit 5f0fabf84d7b52f979dcbafa3d3c530c60d9a92c upstream.

smatch found this error:

CHECK   drivers/net/wireless/mwifiex/join.c
  drivers/net/wireless/mwifiex/join.c:1121
  mwifiex_cmd_802_11_ad_hoc_join()
  error: testing array offset 'i' after use.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agortlwifi: rtl8192cu: Fix problem that prevents reassociation
Larry Finger [Wed, 13 Mar 2013 15:28:13 +0000]
rtlwifi: rtl8192cu: Fix problem that prevents reassociation

commit 9437a248e7cac427c898bdb11bd1ac6844a1ead4 upstream.

The driver was failing to clear the BSSID when a disconnect happened. That
prevented a reconnection. This problem is reported at
https://bugzilla.redhat.com/show_bug.cgi?id=789605,
https://bugzilla.redhat.com/show_bug.cgi?id=866786,
https://bugzilla.redhat.com/show_bug.cgi?id=906734, and
https://bugzilla.kernel.org/show_bug.cgi?id=46171.

Thanks to Jussi Kivilinna for making the critical observation
that led to the solution.

Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agortlwifi: rtl8192cu: Fix schedule while atomic bug splat
Larry Finger [Wed, 27 Feb 2013 20:10:30 +0000]
rtlwifi: rtl8192cu: Fix schedule while atomic bug splat

commit 664899786cb49cb52f620e06ac19c0be524a7cfa upstream.

When run at debug 3 or higher, rtl8192cu reports a BUG as follows:

BUG: scheduling while atomic: kworker/u:0/5281/0x00000002
INFO: lockdep is turned off.
Modules linked in: rtl8192cu rtl8192c_common rtlwifi fuse af_packet bnep bluetooth b43 mac80211 cfg80211 ipv6 snd_hda_codec_conexant kvm_amd k
vm snd_hda_intel snd_hda_codec bcma rng_core snd_pcm ssb mmc_core snd_seq snd_timer snd_seq_device snd i2c_nforce2 sr_mod pcmcia forcedeth i2c_core soundcore
 cdrom sg serio_raw k8temp hwmon joydev ac battery pcmcia_core snd_page_alloc video button wmi autofs4 ext4 mbcache jbd2 crc16 thermal processor scsi_dh_alua
 scsi_dh_hp_sw scsi_dh_rdac scsi_dh_emc scsi_dh ata_generic pata_acpi pata_amd [last unloaded: rtlwifi]
Pid: 5281, comm: kworker/u:0 Tainted: G        W    3.8.0-wl+ #119
Call Trace:
 [<ffffffff814531e7>] __schedule_bug+0x62/0x70
 [<ffffffff81459af0>] __schedule+0x730/0xa30
 [<ffffffff81326e49>] ? usb_hcd_link_urb_to_ep+0x19/0xa0
 [<ffffffff8145a0d4>] schedule+0x24/0x70
 [<ffffffff814575ec>] schedule_timeout+0x18c/0x2f0
 [<ffffffff81459ec0>] ? wait_for_common+0x40/0x180
 [<ffffffff8133f461>] ? ehci_urb_enqueue+0xf1/0xee0
 [<ffffffff810a579d>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff81459f65>] wait_for_common+0xe5/0x180
 [<ffffffff8107d1c0>] ? try_to_wake_up+0x2d0/0x2d0
 [<ffffffff8145a08e>] wait_for_completion_timeout+0xe/0x10
 [<ffffffff8132ab1c>] usb_start_wait_urb+0x8c/0x100
 [<ffffffff8132adf9>] usb_control_msg+0xd9/0x130
 [<ffffffffa057dd8d>] _usb_read_sync+0xcd/0x140 [rtlwifi]
 [<ffffffffa057de0e>] _usb_read32_sync+0xe/0x10 [rtlwifi]
 [<ffffffffa04b0555>] rtl92cu_update_hal_rate_table+0x1a5/0x1f0 [rtl8192cu]

The cause is a synchronous read from routine rtl92cu_update_hal_rate_table().
The resulting output is not critical, thus the debug statement is
deleted.

Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agotracing: Fix free of probe entry by calling call_rcu_sched()
Steven Rostedt (Red Hat) [Wed, 13 Mar 2013 15:15:19 +0000]
tracing: Fix free of probe entry by calling call_rcu_sched()

commit 740466bc89ad8bd5afcc8de220f715f62b21e365 upstream.

Because function tracing is very invasive, and can even trace
calls to rcu_read_lock(), RCU access in function tracing is done
with preempt_disable_notrace(). This requires a synchronize_sched()
for updates and not a synchronize_rcu().

Function probes (traceon, traceoff, etc) must be freed after
a synchronize_sched() after its entry has been removed from the
hash. But call_rcu() is used. Fix this by using call_rcu_sched().

Also fix the usage to use hlist_del_rcu() instead of hlist_del().

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agotracing: Fix race in snapshot swapping
Steven Rostedt (Red Hat) [Tue, 12 Mar 2013 15:32:32 +0000]
tracing: Fix race in snapshot swapping

commit 2721e72dd10f71a3ba90f59781becf02638aa0d9 upstream.

Although the swap is wrapped with a spin_lock, the assignment
of the temp buffer used to swap is not within that lock.
It needs to be moved into that lock, otherwise two swaps
happening on two different CPUs, can end up using the wrong
temp buffer to assign in the swap.

Luckily, all current callers of the swap function appear to have
their own locks. But in case something is added that allows two
different callers to call the swap, then there's a chance that
this race can trigger and corrupt the buffers.

New code is coming soon that will allow for this race to trigger.

I've Cc'd stable, so this bug will not show up if someone backports
one of the changes that can trigger this bug.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agodrm/i915: restrict kernel address leak in debugfs
Kees Cook [Mon, 11 Mar 2013 19:25:19 +0000]
drm/i915: restrict kernel address leak in debugfs

commit 2563a4524febe8f4a98e717e02436d1aaf672aa2 upstream.

Masks kernel address info-leak in object dumps with the %pK suffix,
so they cannot be used to target kernel memory corruption attacks if
the kptr_restrict sysctl is set.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoALSA: snd-usb: mixer: ignore -EINVAL in snd_usb_mixer_controls()
Daniel Mack [Tue, 19 Mar 2013 20:09:25 +0000]
ALSA: snd-usb: mixer: ignore -EINVAL in snd_usb_mixer_controls()

commit 83ea5d18d74f032a760fecde78c0210f66f7f70c upstream.

Creation of individual mixer controls may fail, but that shouldn't cause
the entire mixer creation to fail. Even worse, if the mixer creation
fails, that will error out the entire device probing.

All the functions called by parse_audio_unit() should return -EINVAL if
they find descriptors that are unsupported or believed to be malformed,
so we can safely handle this error code as a non-fatal condition in
snd_usb_mixer_controls().

That fixes a long standing bug which is commonly worked around by
adding quirks which make the driver ignore entire interfaces. Some of
them might now be unnecessary.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Rodolfo Thomazelli <pe.soberbo@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoALSA: snd-usb: mixer: propagate errors up the call chain
Daniel Mack [Tue, 19 Mar 2013 20:09:24 +0000]
ALSA: snd-usb: mixer: propagate errors up the call chain

commit 4d7b86c98e445b075c2c4c3757eb6d3d6efbe72e upstream.

In check_input_term() and parse_audio_feature_unit(), propagate the
error value that has been returned by a failing function instead of
-EINVAL. That helps cleaning up the error pathes in the mixer.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoALSA: hda - Fix typo in checking IEC958 emphasis bit
Takashi Iwai [Wed, 20 Mar 2013 14:42:00 +0000]
ALSA: hda - Fix typo in checking IEC958 emphasis bit

commit a686fd141e20244ad75f80ad54706da07d7bb90a upstream.

There is a typo in convert_to_spdif_status() about checking the
emphasis IEC958 status bit.  It should check the given value instead
of the resultant value.

Reported-by: Martin Weishart <martin.weishart@telosalliance.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoALSA: hda/cirrus - Fix the digital beep registration
Takashi Iwai [Mon, 18 Mar 2013 10:00:44 +0000]
ALSA: hda/cirrus - Fix the digital beep registration

commit a86b1a2cd2f81f74e815e07f756edd7bc5b6f034 upstream.

The argument passed to snd_hda_attach_beep_device() is a widget NID
while spec->beep_amp holds the composed value for amp controls.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Only use TX push if a single descriptor is to be written
Ben Hutchings [Wed, 27 Feb 2013 16:50:38 +0000]
sfc: Only use TX push if a single descriptor is to be written

[ Upstream commit fae8563b25f73dc584a07bcda7a82750ff4f7672 ]

Using TX push when notifying the NIC of multiple new descriptors in
the ring will very occasionally cause the TX DMA engine to re-use an
old descriptor.  This can result in a duplicated or partly duplicated
packet (new headers with old data), or an IOMMU page fault.  This does
not happen when the pushed descriptor is the only one written.

TX push also provides little latency benefit when a packet requires
more than one descriptor.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Disable soft interrupt handling during efx_device_detach_sync()
Ben Hutchings [Tue, 5 Mar 2013 01:03:47 +0000]
sfc: Disable soft interrupt handling during efx_device_detach_sync()

[ Upstream commit 35205b211c8d17a8a0b5e8926cb7c73e9a7ef1ad ]

efx_device_detach_sync() locks all TX queues before marking the device
detached and thus disabling further TX scheduling.  But it can still
be interrupted by TX completions which then result in TX scheduling in
soft interrupt context.  This will deadlock when it tries to acquire
a TX queue lock that efx_device_detach_sync() already acquired.

To avoid deadlock, we must use netif_tx_{,un}lock_bh().

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Detach net device when stopping queues for reconfiguration
Ben Hutchings [Mon, 28 Jan 2013 19:01:06 +0000]
sfc: Detach net device when stopping queues for reconfiguration

[ Upstream commit 29c69a4882641285a854d6d03ca5adbba68c0034 ]

We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned.  Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.

The device is ready if all the following are true:

(a) It has a qdisc
(b) It is marked present
(c) It is running
(d) The link is reported up

(a) and (c) are normally true, and must not be changed by a driver.
(d) is under our control, but fake link changes may disturb userland.
This leaves (b).  We already mark the device absent during reset
and self-test, but we need to do the same during MTU changes and ring
reallocation.  We don't need to do this when the device is brought
down because then (c) is already false.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Fix efx_rx_buf_offset() in the presence of swiotlb
Ben Hutchings [Thu, 10 Jan 2013 23:51:54 +0000]
sfc: Fix efx_rx_buf_offset() in the presence of swiotlb

[ Upstream commits b590ace09d51cd39744e0f7662c5e4a0d1b5d952 and
  c73e787a8db9117d59b5180baf83203a42ecadca ]

We assume that the mapping between DMA and virtual addresses is done
on whole pages, so we can find the page offset of an RX buffer using
the lower bits of the DMA address.  However, swiotlb maps in units of
2K, breaking this assumption.

Add an explicit page_offset field to struct efx_rx_buffer.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Properly sync RX DMA buffer when it is not the last in the page
Ben Hutchings [Thu, 20 Dec 2012 18:48:20 +0000]
sfc: Properly sync RX DMA buffer when it is not the last in the page

[ Upstream commit 3a68f19d7afb80f548d016effbc6ed52643a8085 ]

We may currently allocate two RX DMA buffers to a page, and only unmap
the page when the second is completed.  We do not sync the first RX
buffer to be completed; this can result in packet loss or corruption
if the last RX buffer completed in a NAPI poll is the first in a page
and is not DMA-coherent.  (In the middle of a NAPI poll, we will
handle the following RX completion and unmap the page *before* looking
at the content of the first buffer.)

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Backported to 3.4: adjust context]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Correctly initialise reset_method in siena_test_chip()
Ben Hutchings [Sat, 1 Dec 2012 01:55:27 +0000]
sfc: Correctly initialise reset_method in siena_test_chip()

[ Upstream commit ef492f11efed9a6a1686bf914fb74468df59385c ]

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Avoid generating over-length MC_CMD_FLUSH_RX_QUEUES request
Ben Hutchings [Wed, 19 Sep 2012 01:53:34 +0000]
sfc: Avoid generating over-length MC_CMD_FLUSH_RX_QUEUES request

[ Upstream commit 450783747f42dfa3883920acfad4acdd93ce69af ]

MCDI supports requests up to 252 bytes long, which is only enough to
pass 63 RX queue IDs to MC_CMD_FLUSH_RX_QUEUES.  However a VF may have
up to 64 RX queues, and if we try to flush them all we will generate
an over-length request and BUG() in efx_mcdi_copyin().  Currently
all VF drivers limit themselves to 32 RX queues, so reducing the
limit to 63 does no harm.

Also add a BUILD_BUG_ON in efx_mcdi_flush_rxqs() so we remember to
deal with the same problem there if EFX_MAX_CHANNELS is increased.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Disable VF queues during register self-test
Ben Hutchings [Wed, 4 Jul 2012 02:58:33 +0000]
sfc: Disable VF queues during register self-test

[ Upstream commit d4f2cecce138c34960c467d0ae38a6d4bcd6af7b ]

Currently VF queues and drivers may remain active during this test.
This could cause memory corruption or spurious test failures.
Therefore we reset the port/function before running these tests on
Siena.

On Falcon this doesn't work: we have to do some additional
initialisation before some blocks will work again.  So refactor the
reset/register-test sequence into an efx_nic_type method so
efx_selftest() doesn't have to consider such quirks.

In the process, fix another minor bug: Siena does not have an
'invisible' reset and the self-test currently fails to push the PHY
configuration after resetting.  Passing RESET_TYPE_ALL to
efx_reset_{down,up}() fixes this.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Fix timekeeping in efx_mcdi_poll()
Ben Hutchings [Sat, 1 Dec 2012 02:21:17 +0000]
sfc: Fix timekeeping in efx_mcdi_poll()

[ Upstream commit ebf98e797b4e26ad52ace1511a0b503ee60a6cd4 ]

efx_mcdi_poll() uses get_seconds() to read the current time and to
implement a polling timeout.  The use of this function was chosen
partly because it could easily be replaced in a co-sim environment
with a macro that read the simulated time.

Unfortunately the real get_seconds() returns the system time (real
time) which is subject to adjustment by e.g. ntpd.  If the system time
is adjusted forward during a polled MCDI operation, the effective
timeout can be shorter than the intended 10 seconds, resulting in a
spurious failure.  It is also possible for a backward adjustment to
delay detection of a areal failure.

Use jiffies instead, and change MCDI_RPC_TIMEOUT to be denominated in
jiffies.  Also correct rounding of the timeout: check time > finish
(or rather time_after(time, finish)) and not time >= finish.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: lock TX queues when calling netif_device_detach()
Daniel Pieczko [Wed, 17 Oct 2012 12:21:23 +0000]
sfc: lock TX queues when calling netif_device_detach()

[ Upstream commit c2f3b8e3a44b6fe9e36704e30157ebe1a88c08b1 ]

The assertion of netif_device_present() at the top of
efx_hard_start_xmit() may fail if we don't do this.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Backported to 3.4: adjust context]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Work-around flush timeout when flushes have completed
Daniel Pieczko [Tue, 2 Oct 2012 12:36:18 +0000]
sfc: Work-around flush timeout when flushes have completed

[ Upstream commit 525d9e824018cd7cc8d8d44832ddcd363abfe6e1 ]

We sometimes hit a "failed to flush" timeout on some TX queues, but the
flushes have completed and the flush completion events seem to go missing.
In this case, we can check the TX_DESC_PTR_TBL register and drain the
queues if the flushes had finished.

[bwh: Minor fixes to coding style]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Really disable flow control while flushing
Ben Hutchings [Thu, 6 Sep 2012 15:52:31 +0000]
sfc: Really disable flow control while flushing

[ Upstream commit d5e8cc6c946e0857826dcfbb3585068858445bfe ]

Receiving pause frames can block TX queue flushes.  Earlier changes
work around this by reconfiguring the MAC during flushes for VFs, but
during flushes for the PF we would only change the fc_disable counter.
Unless the MAC is reconfigured for some other reason during the flush
(which I would not expect to happen) this had no effect at all.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Fix MCDI structure field lookup
Ben Hutchings [Tue, 11 Sep 2012 20:46:41 +0000]
sfc: Fix MCDI structure field lookup

[ Upstream commit 0a6e5008a9df678b48f8d4e57601aa4270df6c14 ]

The least significant bit number (LBN) of a field within an MCDI
structure is counted from the start of the structure, not the
containing dword.  In MCDI_ARRAY_FIELD() we need to mask it rather
than using the usual EFX_DWORD_FIELD() macro.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Add parentheses around use of bitfield macro arguments
Ben Hutchings [Tue, 11 Sep 2012 20:37:36 +0000]
sfc: Add parentheses around use of bitfield macro arguments

[ Upstream commit 9724a8504c875145f5a513bb8eca50671cee23b4 ]

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Convert firmware subtypes to native byte order in efx_mcdi_get_board_cfg()
Ben Hutchings [Thu, 6 Sep 2012 23:58:10 +0000]
sfc: Convert firmware subtypes to native byte order in efx_mcdi_get_board_cfg()

[ Upstream commit bfeed902946a31692e7a24ed355b6d13ac37d014 ]

On big-endian systems the MTD partition names currently have mangled
subtype numbers and are not recognised by the firmware update tool
(sfupdate).

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosfc: Do not attempt to flush queues if DMA is disabled
Stuart Hodgson [Fri, 30 Mar 2012 12:04:51 +0000]
sfc: Do not attempt to flush queues if DMA is disabled

[ Upstream commit 3dca9d2dc285faf1910d405b65df845cab061356 ]

efx_nic_fatal_interrupt() disables DMA before scheduling a reset.
After this, we need not and *cannot* flush queues.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoinet: limit length of fragment queue hash table bucket lists
Hannes Frederic Sowa [Fri, 15 Mar 2013 11:32:30 +0000]
inet: limit length of fragment queue hash table bucket lists

[ Upstream commit 5a3da1fe9561828d0ca7eca664b16ec2b9bf0055 ]

This patch introduces a constant limit of the fragment queue hash
table bucket list lengths. Currently the limit 128 is choosen somewhat
arbitrary and just ensures that we can fill up the fragment cache with
empty packets up to the default ip_frag_high_thresh limits. It should
just protect from list iteration eating considerable amounts of cpu.

If we reach the maximum length in one hash bucket a warning is printed.
This is implemented on the caller side of inet_frag_find to distinguish
between the different users of inet_fragment.c.

I dropped the out of memory warning in the ipv4 fragment lookup path,
because we already get a warning by the slab allocator.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jesper Dangaard Brouer <jbrouer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agobnx2x: fix occasional statistics off-by-4GB error
Maciej Żenczykowski [Fri, 15 Mar 2013 11:56:17 +0000]
bnx2x: fix occasional statistics off-by-4GB error

[ Upstream commit b009aac12cd0fe34293c68af8ac48b85be3bd858 ]

The UPDATE_QSTAT function introduced on February 15, 2012
in commit 1355b704b9ba "bnx2x: consistent statistics after
internal driver reload" incorrectly fails to handle overflow
during addition of the lower 32-bit field of a stat.

This bug is present since 3.4-rc1 and should thus be considered
a candidate for stable 3.4+ releases.

Google-Bug-Id: 8374428
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Mintz Yuval <yuvalmin@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agovhost/net: fix heads usage of ubuf_info
Michael S. Tsirkin [Sun, 17 Mar 2013 02:46:09 +0000]
vhost/net: fix heads usage of ubuf_info

[ Upstream commit 46aa92d1ba162b4b3d6b7102440e459d4e4ee255 ]

ubuf info allocator uses guest controlled head as an index,
so a malicious guest could put the same head entry in the ring twice,
and we will get two callbacks on the same value.
To fix use upend_idx which is guaranteed to be unique.

Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agortnetlink: Mask the rta_type when range checking
Vlad Yasevich [Wed, 13 Mar 2013 04:18:58 +0000]
rtnetlink: Mask the rta_type when range checking

[ Upstream commit a5b8db91442fce9c9713fcd656c3698f1adde1d6 ]

Range/validity checks on rta_type in rtnetlink_rcv_msg() do
not account for flags that may be set.  This causes the function
to return -EINVAL when flags are set on the type (for example
NLA_F_NESTED).

Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agotcp: fix skb_availroom()
Eric Dumazet [Thu, 14 Mar 2013 05:40:32 +0000]
tcp: fix skb_availroom()

[ Upstream commit 16fad69cfe4adbbfa813de516757b87bcae36d93 ]

Chrome OS team reported a crash on a Pixel ChromeBook in TCP stack :

https://code.google.com/p/chromium/issues/detail?id=182056

commit a21d45726acac (tcp: avoid order-1 allocations on wifi and tx
path) did a poor choice adding an 'avail_size' field to skb, while
what we really needed was a 'reserved_tailroom' one.

It would have avoided commit 22b4a4f22da (tcp: fix retransmit of
partially acked frames) and this commit.

Crash occurs because skb_split() is not aware of the 'avail_size'
management (and should not be aware)

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Mukesh Agrawal <quiche@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoipv4: fix definition of FIB_TABLE_HASHSZ
Denis V. Lunev [Wed, 13 Mar 2013 00:24:15 +0000]
ipv4: fix definition of FIB_TABLE_HASHSZ

[ Upstream commit 5b9e12dbf92b441b37136ea71dac59f05f2673a9 ]

a long time ago by the commit

  commit 93456b6d7753def8760b423ac6b986eb9d5a4a95
  Author: Denis V. Lunev <den@openvz.org>
  Date:   Thu Jan 10 03:23:38 2008 -0800

    [IPV4]: Unify access to the routing tables.

the defenition of FIB_HASH_TABLE size has obtained wrong dependency:
it should depend upon CONFIG_IP_MULTIPLE_TABLES (as was in the original
code) but it was depended from CONFIG_IP_ROUTE_MULTIPATH

This patch returns the situation to the original state.

The problem was spotted by Tingwei Liu.

Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Tingwei Liu <tingw.liu@gmail.com>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosctp: don't break the loop while meeting the active_path so as to find the matched...
Xufeng Zhang [Thu, 7 Mar 2013 21:39:37 +0000]
sctp: don't break the loop while meeting the active_path so as to find the matched transport

[ Upstream commit 2317f449af30073cfa6ec8352e4a65a89e357bdd ]

sctp_assoc_lookup_tsn() function searchs which transport a certain TSN
was sent on, if not found in the active_path transport, then go search
all the other transports in the peer's transport_addr_list, however, we
should continue to the next entry rather than break the loop when meet
the active_path transport.

Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosctp: Use correct sideffect command in duplicate cookie handling
Vlad Yasevich [Tue, 12 Mar 2013 15:53:23 +0000]
sctp: Use correct sideffect command in duplicate cookie handling

[ Upstream commit f2815633504b442ca0b0605c16bf3d88a3a0fcea ]

When SCTP is done processing a duplicate cookie chunk, it tries
to delete a newly created association.  For that, it has to set
the right association for the side-effect processing to work.
However, when it uses the SCTP_CMD_NEW_ASOC command, that performs
more work then really needed (like hashing the associationa and
assigning it an id) and there is no point to do that only to
delete the association as a next step.  In fact, it also creates
an impossible condition where an association may be found by
the getsockopt() call, and that association is empty.  This
causes a crash in some sctp getsockopts.

The solution is rather simple.  We simply use SCTP_CMD_SET_ASOC
command that doesn't have all the overhead and does exactly
what we need.

Reported-by: Karl Heiss <kheiss@gmail.com>
Tested-by: Karl Heiss <kheiss@gmail.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agotg3: 5715 does not link up when autoneg off
Nithin Sujir [Tue, 12 Mar 2013 15:32:48 +0000]
tg3: 5715 does not link up when autoneg off

[ Upstream commit 7c6cdead7cc9a99650d15497aae47d7472217eb1 ]

Commit d13ba512cbba7de5d55d7a3b2aae7d83c8921457 ("tg3: Remove
SPEED_UNKNOWN checks") cleaned up the autoneg advertisement by
removing some dead code. One effect of this change was that the
advertisement register would not be updated if autoneg is turned off.

This exposed a bug on the 5715 device w.r.t linking. The 5715 defaults
to advertise only 10Mb Full duplex. But with autoneg disabled, it needs
the configured speed enabled in the advertisement register to link up.

This patch adds the work around to advertise all speeds on the 5715 when
autoneg is disabled.

Reported-by: Marcin Miotk <marcinmiotk81@gmail.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agobonding: don't call update_speed_duplex() under spinlocks
Veaceslav Falico [Tue, 12 Mar 2013 06:31:32 +0000]
bonding: don't call update_speed_duplex() under spinlocks

[ Upstream commit 876254ae2758d50dcb08c7bd00caf6a806571178 ]

bond_update_speed_duplex() might sleep while calling underlying slave's
routines. Move it out of atomic context in bond_enslave() and remove it
from bond_miimon_commit() - it was introduced by commit 546add79, however
when the slave interfaces go up/change state it's their responsibility to
fire NETDEV_UP/NETDEV_CHANGE events so that bonding can properly update
their speed.

I've tested it on all combinations of ifup/ifdown, autoneg/speed/duplex
changes, remote-controlled and local, on (not) MII-based cards. All changes
are visible.

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agonetconsole: don't call __netpoll_cleanup() while atomic
Veaceslav Falico [Mon, 11 Mar 2013 00:21:48 +0000]
netconsole: don't call __netpoll_cleanup() while atomic

[ Upstream commit 3f315bef23075ea8a98a6fe4221a83b83456d970 ]

__netpoll_cleanup() is called in netconsole_netdev_event() while holding a
spinlock. Release/acquire the spinlock before/after it and restart the
loop. Also, disable the netconsole completely, because we won't have chance
after the restart of the loop, and might end up in a situation where
nt->enabled == 1 and nt->np.dev == NULL.

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agonet/ipv4: Ensure that location of timestamp option is stored
David Ward [Mon, 11 Mar 2013 10:43:39 +0000]
net/ipv4: Ensure that location of timestamp option is stored

[ Upstream commit 4660c7f498c07c43173142ea95145e9dac5a6d14 ]

This is needed in order to detect if the timestamp option appears
more than once in a packet, to remove the option if the packet is
fragmented, etc. My previous change neglected to store the option
location when the router addresses were prespecified and Pointer >
Length. But now the option location is also stored when Flag is an
unrecognized value, to ensure these option handling behaviors are
still performed.

Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agosunsu: Fix panic in case of nonexistent port at "console=ttySY" cmdline option
Tkhai Kirill [Sat, 23 Feb 2013 23:01:15 +0000]
sunsu: Fix panic in case of nonexistent port at "console=ttySY" cmdline option

[ Upstream commit cb29529ea0030e60ef1bbbf8399a43d397a51526 ]

If a machine has X (X < 4) sunsu ports and cmdline
option "console=ttySY" is passed, where X < Y <= 4,
than the following panic happens:

Unable to handle kernel NULL pointer dereference
TPC: <sunsu_console_setup+0x78/0xe0>
RPC: <sunsu_console_setup+0x74/0xe0>
I7: <register_console+0x378/0x3e0>
Call Trace:
 [0000000000453a38] register_console+0x378/0x3e0
 [0000000000576fa0] uart_add_one_port+0x2e0/0x340
 [000000000057af40] su_probe+0x160/0x2e0
 [00000000005b8a4c] platform_drv_probe+0xc/0x20
 [00000000005b6c2c] driver_probe_device+0x12c/0x220
 [00000000005b6da8] __driver_attach+0x88/0xa0
 [00000000005b4df4] bus_for_each_dev+0x54/0xa0
 [00000000005b5a54] bus_add_driver+0x154/0x260
 [00000000005b7190] driver_register+0x50/0x180
 [00000000006d250c] sunsu_init+0x18c/0x1e0
 [00000000006c2668] do_one_initcall+0xe8/0x160
 [00000000006c282c] kernel_init_freeable+0x12c/0x1e0
 [0000000000603764] kernel_init+0x4/0x100
 [0000000000405f64] ret_from_syscall+0x1c/0x2c
 [0000000000000000]           (null)

1)Fix the panic;
2)Increment registered port number every successful
probe.

Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoRevert "USB: EHCI: don't check DMA values in QH overlays"
Greg Kroah-Hartman [Wed, 20 Mar 2013 21:16:12 +0000]
Revert "USB: EHCI: don't check DMA values in QH overlays"

This reverts commit 0319f9909ce68a7516dfc8d53400e07168d281a8, which is commit
feca7746d5d9e84b105a613b7f3b6ad00d327372 upstream.

It shouldn't have gone into this stable release.

Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Joseph Salisbury <joseph.salisbury@canonical.com>
Cc: Stephen Thirlwall <sdt@dr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoLinux 3.4.37
Greg Kroah-Hartman [Wed, 20 Mar 2013 20:05:12 +0000]
Linux 3.4.37

6 years ago6lowpan: Fix endianness issue in is_addr_link_local().
YOSHIFUJI Hideaki [Sat, 9 Mar 2013 09:11:57 +0000]
6lowpan: Fix endianness issue in is_addr_link_local().

[ Upstream commit 9026c4927254f5bea695cc3ef2e255280e6a3011 ]

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agodcbnl: fix various netlink info leaks
Mathias Krause [Sat, 9 Mar 2013 05:52:21 +0000]
dcbnl: fix various netlink info leaks

[ Upstream commit 29cd8ae0e1a39e239a3a7b67da1986add1199fc0 ]

The dcb netlink interface leaks stack memory in various places:
* perm_addr[] buffer is only filled at max with 12 of the 32 bytes but
  copied completely,
* no in-kernel driver fills all fields of an IEEE 802.1Qaz subcommand,
  so we're leaking up to 58 bytes for ieee_ets structs, up to 136 bytes
  for ieee_pfc structs, etc.,
* the same is true for CEE -- no in-kernel driver fills the whole
  struct,

Prevent all of the above stack info leaks by properly initializing the
buffers/structures involved.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agortnl: fix info leak on RTM_GETLINK request for VF devices
Mathias Krause [Sat, 9 Mar 2013 05:52:20 +0000]
rtnl: fix info leak on RTM_GETLINK request for VF devices

[ Upstream commit 84d73cd3fb142bf1298a8c13fd4ca50fd2432372 ]

Initialize the mac address buffer with 0 as the driver specific function
will probably not fill the whole buffer. In fact, all in-kernel drivers
fill only ETH_ALEN of the MAX_ADDR_LEN bytes, i.e. 6 of the 32 possible
bytes. Therefore we currently leak 26 bytes of stack memory to userland
via the netlink interface.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agoipv6: stop multicast forwarding to process interface scoped addresses
Hannes Frederic Sowa [Fri, 8 Mar 2013 02:07:23 +0000]
ipv6: stop multicast forwarding to process interface scoped addresses

[ Upstream commit ddf64354af4a702ee0b85d0a285ba74c7278a460 ]

v2:
a) used struct ipv6_addr_props

v3:
a) reverted changes for ipv6_addr_props

v4:
a) do not use __ipv6_addr_needs_scope_id

Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agobridging: fix rx_handlers return code
Cristian Bercaru [Fri, 8 Mar 2013 07:03:38 +0000]
bridging: fix rx_handlers return code

[ Upstream commit 3bc1b1add7a8484cc4a261c3e128dbe1528ce01f ]

The frames for which rx_handlers return RX_HANDLER_CONSUMED are no longer
counted as dropped. They are counted as successfully received by
'netif_receive_skb'.

This allows network interface drivers to correctly update their RX-OK and
RX-DRP counters based on the result of 'netif_receive_skb'.

Signed-off-by: Cristian Bercaru <B43982@freescale.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agonetlabel: correctly list all the static label mappings
Paul Moore [Wed, 6 Mar 2013 11:45:24 +0000]
netlabel: correctly list all the static label mappings

[ Upstream commits 0c1233aba1e948c37f6dc7620cb7c253fcd71ce9 and
  a6a8fe950e1b8596bb06f2c89c3a1a4bf2011ba9 ]

When we have a large number of static label mappings that spill across
the netlink message boundary we fail to properly save our state in the
netlink_callback struct which causes us to repeat the same listings.
This patch fixes this problem by saving the state correctly between
calls to the NetLabel static label netlink "dumpit" routines.

Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agomacvlan: Set IFF_UNICAST_FLT flag to prevent unnecessary promisc mode.
Vlad Yasevich [Thu, 7 Mar 2013 10:21:48 +0000]
macvlan: Set IFF_UNICAST_FLT flag to prevent unnecessary promisc mode.

[ Upstream commit 87ab7f6f2874f1115817e394a7ed2dea1c72549e ]

Macvlan already supports hw address filters.  Set the IFF_UNICAST_FLT
so that it doesn't needlesly enter PROMISC mode when macvlans are
stacked.

Signed-of-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agotun: add a missing nf_reset() in tun_net_xmit()
Eric Dumazet [Wed, 6 Mar 2013 11:02:37 +0000]
tun: add a missing nf_reset() in tun_net_xmit()

[ Upstream commit f8af75f3517a24838a36eb5797a1a3e60bf9e276 ]

Dave reported following crash :

general protection fault: 0000 [#1] SMP
CPU 2
Pid: 25407, comm: qemu-kvm Not tainted 3.7.9-205.fc18.x86_64 #1 Hewlett-Packard HP Z400 Workstation/0B4Ch
RIP: 0010:[<ffffffffa0399bd5>]  [<ffffffffa0399bd5>] destroy_conntrack+0x35/0x120 [nf_conntrack]
RSP: 0018:ffff880276913d78  EFLAGS: 00010206
RAX: 50626b6b7876376c RBX: ffff88026e530d68 RCX: ffff88028d158e00
RDX: ffff88026d0d5470 RSI: 0000000000000011 RDI: 0000000000000002
RBP: ffff880276913d88 R08: 0000000000000000 R09: ffff880295002900
R10: 0000000000000000 R11: 0000000000000003 R12: ffffffff81ca3b40
R13: ffffffff8151a8e0 R14: ffff880270875000 R15: 0000000000000002
FS:  00007ff3bce38a00(0000) GS:ffff88029fc40000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007fd1430bd000 CR3: 000000027042b000 CR4: 00000000000027e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process qemu-kvm (pid: 25407, threadinfo ffff880276912000, task ffff88028c369720)
Stack:
 ffff880156f59100 ffff880156f59100 ffff880276913d98 ffffffff815534f7
 ffff880276913db8 ffffffff8151a74b ffff880270875000 ffff880156f59100
 ffff880276913dd8 ffffffff8151a5a6 ffff880276913dd8 ffff88026d0d5470
Call Trace:
 [<ffffffff815534f7>] nf_conntrack_destroy+0x17/0x20
 [<ffffffff8151a74b>] skb_release_head_state+0x7b/0x100
 [<ffffffff8151a5a6>] __kfree_skb+0x16/0xa0
 [<ffffffff8151a666>] kfree_skb+0x36/0xa0
 [<ffffffff8151a8e0>] skb_queue_purge+0x20/0x40
 [<ffffffffa02205f7>] __tun_detach+0x117/0x140 [tun]
 [<ffffffffa022184c>] tun_chr_close+0x3c/0xd0 [tun]
 [<ffffffff8119669c>] __fput+0xec/0x240
 [<ffffffff811967fe>] ____fput+0xe/0x10
 [<ffffffff8107eb27>] task_work_run+0xa7/0xe0
 [<ffffffff810149e1>] do_notify_resume+0x71/0xb0
 [<ffffffff81640152>] int_signal+0x12/0x17
Code: 00 00 04 48 89 e5 41 54 53 48 89 fb 4c 8b a7 e8 00 00 00 0f 85 de 00 00 00 0f b6 73 3e 0f b7 7b 2a e8 10 40 00 00 48 85 c0 74 0e <48> 8b 40 28 48 85 c0 74 05 48 89 df ff d0 48 c7 c7 08 6a 3a a0
RIP  [<ffffffffa0399bd5>] destroy_conntrack+0x35/0x120 [nf_conntrack]
 RSP <ffff880276913d78>

This is because tun_net_xmit() needs to call nf_reset()
before queuing skb into receive_queue

Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

6 years agotcp: fix double-counted receiver RTT when leaving receiver fast path
Neal Cardwell [Mon, 4 Mar 2013 06:23:05 +0000]
tcp: fix double-counted receiver RTT when leaving receiver fast path

[ Upstream commit aab2b4bf224ef8358d262f95b568b8ad0cecf0a0 ]

We should not update ts_recent and call tcp_rcv_rtt_measure_ts() both
before and after going to step5. That wastes CPU and double-counts the
receiver-side RTT sample.

Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>