10 years agoqlge: Use one path to (re)fill rx buffers.
Ron Mercer [Mon, 23 Feb 2009 10:42:17 +0000]
qlge: Use one path to (re)fill rx buffers.

Currently there are two paths for filling rx buffer queues. One is
used during initialization and the other during runtime.  This patch
removes ql_alloc_sbq_buffers() and ql_alloc_lbq_buffers() and replaces
them with a call to the runtime functions ql_update_lbq() and
ql_update_sbq().

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoqlge: Optimize rx buffer refill process.
Ron Mercer [Mon, 23 Feb 2009 10:42:16 +0000]
qlge: Optimize rx buffer refill process.

RX Buffers are refilled in chunks of 16 at a time before notifying the
hardware with a register write.  This can cause several writes to take
place in a given napi poll call.  This change causes the write to take place
only once at the end of the call.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoqlge: Change frame route hw semaphore granularity.
Ron Mercer [Mon, 23 Feb 2009 10:42:15 +0000]
qlge: Change frame route hw semaphore granularity.

Instead of taking/giving the hw semaphore repeatedly when iterating over
several frame to queue route settings, we have the caller hold it until
all are done.
This reduces PCI bus chatter and possible waits.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoqlge: Increase MAC addr hw sem granularity.
Ron Mercer [Mon, 23 Feb 2009 10:42:14 +0000]
qlge: Increase MAC addr hw sem granularity.

Instead of taking/giving the semaphore repeatedly when iterating over
several adderesses, we have the caller hold it until all are done.  This
reduces PCI bus chatter and possible waits.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoqlge: Clean up mac address and frame route settings.
Ron Mercer [Mon, 23 Feb 2009 10:42:13 +0000]
qlge: Clean up mac address and frame route settings.

Setting MAC addresses and routing frames to various queues will need to
be done in response to firmware events as well as during initialization.
This change encapsulates the facilities into a single call that can
later me made from other places.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agosit: used time_before for comparing jiffies
Wei Yongjun [Wed, 25 Feb 2009 07:37:19 +0000]
sit: used time_before for comparing jiffies

The functions time_before is more robust for comparing
jiffies against other values.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoipip: used time_before for comparing jiffies
Wei Yongjun [Wed, 25 Feb 2009 07:36:47 +0000]
ipip: used time_before for comparing jiffies

The functions time_before is more robust for comparing
jiffies against other values.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agogre: used time_before for comparing jiffies
Wei Yongjun [Wed, 25 Feb 2009 07:34:48 +0000]
gre: used time_before for comparing jiffies

The functions time_before is more robust for comparing
jiffies against other values.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoipv6: Remove some pointless conditionals before kfree_skb()
Wei Yongjun [Mon, 23 Feb 2009 21:45:33 +0000]
ipv6: Remove some pointless conditionals before kfree_skb()

Remove some pointless conditionals before kfree_skb().

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression E;
@@
- if (E)
-  kfree_skb(E);
+ kfree_skb(E);
// </smpl>

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetlink: change nlmsg_notify() return value logic
Pablo Neira Ayuso [Wed, 25 Feb 2009 07:18:28 +0000]
netlink: change nlmsg_notify() return value logic

This patch changes the return value of nlmsg_notify() as follows:

If NETLINK_BROADCAST_ERROR is set by any of the listeners and
an error in the delivery happened, return the broadcast error;
else if there are no listeners apart from the socket that
requested a change with the echo flag, return the result of the
unicast notification. Thus, with this patch, the unicast
notification is handled in the same way of a broadcast listener
that has set the NETLINK_BROADCAST_ERROR socket flag.

This patch is useful in case that the caller of nlmsg_notify()
wants to know the result of the delivery of a netlink notification
(including the broadcast delivery) and take any action in case
that the delivery failed. For example, ctnetlink can drop packets
if the event delivery failed to provide reliable logging and
state-synchronization at the cost of dropping packets.

This patch also modifies the rtnetlink code to ignore the return
value of rtnl_notify() in all callers. The function rtnl_notify()
(before this patch) returned the error of the unicast notification
which makes rtnl_set_sk_err() reports errors to all listeners. This
is not of any help since the origin of the change (the socket that
requested the echoing) notices the ENOBUFS error if the notification
fails and should resync itself.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agomv643xx_eth: set sane default receive coalescing timeout
Lennert Buytenhek [Tue, 24 Feb 2009 15:42:05 +0000]
mv643xx_eth: set sane default receive coalescing timeout

A receive coalescing timeout of 250 usec appears to strike a good
balance between allowing enough received frames to be aggregated for
LRO to do its job and not allowing the connection to stall due to
delaying ACKs to the remote end for too long.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agomv643xx_eth: move a couple of init actions from ->open() to port probe
Lennert Buytenhek [Tue, 24 Feb 2009 15:41:47 +0000]
mv643xx_eth: move a couple of init actions from ->open() to port probe

Move the netif_carrier_off() call in ->open() to port probe, so that
ethtool doesn't report the link as being up before we have up'd the
interface.

Move initialisation of the rx/tx coalescing timers from ->open() to
port probe, so that we don't reset the coalescing timers every time
the interface is up'd.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agomv643xx_eth: convert to net_device_ops
Lennert Buytenhek [Tue, 24 Feb 2009 15:41:40 +0000]
mv643xx_eth: convert to net_device_ops

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agomv643xx_eth: make LRO unconditional
Lennert Buytenhek [Tue, 24 Feb 2009 15:41:32 +0000]
mv643xx_eth: make LRO unconditional

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetxen: refactor pci probe
Dhananjay Phadke [Wed, 25 Feb 2009 00:39:21 +0000]
netxen: refactor pci probe

Split pci probe function into smaller logical blocks.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetxen: cleanup unused code
Dhananjay Phadke [Wed, 25 Feb 2009 00:39:03 +0000]
netxen: cleanup unused code

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetxen: advertise wake-on-lan support
Dhananjay Phadke [Wed, 25 Feb 2009 00:38:44 +0000]
netxen: advertise wake-on-lan support

Add ethtool wake on lan support.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetxen: firmware download support
Dhananjay Phadke [Wed, 25 Feb 2009 00:38:22 +0000]
netxen: firmware download support

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixbge: fix bug when using large pages and jumbo frames
Jesse Brandeburg [Wed, 25 Feb 2009 00:37:31 +0000]
ixbge: fix bug when using large pages and jumbo frames

it was pointed out on the list that ixgbe was failing when using 64kB pages
and large 16kB MTU.

since with a 64kB PAGE_SIZE MAX_SKB_FRAGS = 3, the way the driver was
configuring page usage was assuming 2kB is half a page, and was only
ever dmaing that much data to a half page.

(16kB - header size) / 2048 = 7 or 8 pages, which would far exceed 3

adjust the driver to account for these large pages, the hardware can
support DMA to up to 16kB for each descriptor.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoixgbe: Move ring features into an enum, allowing easier future maintenance
Shannon Nelson [Wed, 25 Feb 2009 00:36:38 +0000]
ixgbe: Move ring features into an enum, allowing easier future maintenance

From: Shannon Nelson <shannon.nelson@intel.com>

The ring_feature member of ixgbe_adapter is statically allocated based on
the supported features of the device.  When a new feature is added, we need
to manually update the static allocation.  This patch makes the feature
list an enum, eliminating the need for multiple updates to the code when
adding a new feature.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoMerge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
David S. Miller [Tue, 24 Feb 2009 11:51:03 +0000]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6

10 years agoMerge branch 'master' of /home/davem/src/GIT/linux-2.6/
David S. Miller [Tue, 24 Feb 2009 11:50:29 +0000]
Merge branch 'master' of /home/davem/src/GIT/linux-2.6/

10 years agoDoc: Refer to ip-sysctl.txt for strict vs. loose rp_filter mode
Jesper Dangaard Brouer [Mon, 23 Feb 2009 04:40:43 +0000]
Doc: Refer to ip-sysctl.txt for strict vs. loose rp_filter mode

The IP_ADVANCED_ROUTER Kconfig describes the rp_filter
proc option.  Recent changes added a loose mode.
Instead of documenting this change too places, refer to
the document describing it:
 Documentation/networking/ip-sysctl.txt

I'm considering moving the rp_filter description away
from the Kconfig file into ip-sysctl.txt.

Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoDoc: Cleanup whitespaces in ip-sysctl.txt
Jesper Dangaard Brouer [Mon, 23 Feb 2009 04:39:04 +0000]
Doc: Cleanup whitespaces in ip-sysctl.txt

Fix up whitespaces while going though ip-sysctl.txt anyway.

Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoDoc: Fix typos in ip-sysctl.txt about rp_filter.
Jesper Dangaard Brouer [Mon, 23 Feb 2009 04:37:55 +0000]
Doc: Fix typos in ip-sysctl.txt about rp_filter.

First fix a typo in Stephens patch ;-)

Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetxen: handle pci bar 0 mapping failure
Dhananjay Phadke [Tue, 24 Feb 2009 11:44:23 +0000]
netxen: handle pci bar 0 mapping failure

PCI bar 0 is used for memory mapped register access.
If ioremap fails (returns NULL), register access results
in crash.

Use pci_ioremap_bar() instead of ioremap(), the latter
fails on on 32 bit powerpc where pci resource address is
> 32 bits.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetxen: fix physical port mapping
Dhananjay Phadke [Tue, 24 Feb 2009 11:42:59 +0000]
netxen: fix physical port mapping

The PCI function to physical port mapping is valid only for
old firmware. New firmware (4.0.0+) abstracts this.
So driver should never try to access phy using invalid
mapping. The behavior is unpredictable when PCI functions
4-7 are enabled on the same NIC.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Tue, 24 Feb 2009 04:29:21 +0000]
Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: amend the fix for SO_BSDCOMPAT gsopt infoleak
  netns: build fix for net_alloc_generic

10 years agoproc: proc_get_inode should de_put when inode already initialized
Krzysztof Sachanowicz [Mon, 23 Feb 2009 21:21:55 +0000]
proc: proc_get_inode should de_put when inode already initialized

de_get is called before every proc_get_inode, but corresponding de_put is
called only when dropping last reference to an inode. This might cause
something like
remove_proc_entry: /proc/stats busy, count=14496
to be printed to the syslog.

The fix is to call de_put in case of an already initialized inode in
proc_get_inode.

Signed-off-by: Krzysztof Sachanowicz <analyzer1@gmail.com>
Tested-by: Marcin Pilipczuk <marcin.pilipczuk@gmail.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoi915: suspend/resume interrupt state
Jesse Barnes [Mon, 23 Feb 2009 23:41:09 +0000]
i915: suspend/resume interrupt state

In the KMS case, enter/leavevt won't fix up the interrupt handler for
us, so we need to do it at suspend/resume time.  Make sure we don't fail
the resume if the chip is hung either.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoFix an oops in i915_gem_retire_requests()
Karsten Wiese [Mon, 23 Feb 2009 14:07:57 +0000]
Fix an oops in i915_gem_retire_requests()

dev_priv->hw_status_page can be NULL, if i915_gem_retire_requests()
is called from i915_gem_busy_ioctl().

Signed-off-by Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agonet: amend the fix for SO_BSDCOMPAT gsopt infoleak
Eugene Teo [Mon, 23 Feb 2009 23:38:41 +0000]
net: amend the fix for SO_BSDCOMPAT gsopt infoleak

The fix for CVE-2009-0676 (upstream commit df0bca04) is incomplete. Note
that the same problem of leaking kernel memory will reappear if someone
on some architecture uses struct timeval with some internal padding (for
example tv_sec 64-bit and tv_usec 32-bit) --- then, you are going to
leak the padded bytes to userspace.

Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetns: build fix for net_alloc_generic
Clemens Noss [Mon, 23 Feb 2009 23:37:35 +0000]
netns: build fix for net_alloc_generic

net_alloc_generic was defined in #ifdef CONFIG_NET_NS, but used
unconditionally. Move net_alloc_generic out of #ifdef.

Signed-off-by: Clemens Noss <cnoss@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Linus Torvalds [Mon, 23 Feb 2009 22:38:20 +0000]
Merge git://git./linux/kernel/git/herbert/crypto-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ahash - Fix digest size in /proc/crypto

10 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Mon, 23 Feb 2009 22:36:05 +0000]
Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  netns: fix double free at netns creation
  veth : add the set_mac_address capability
  sunlance: Beyond ARRAY_SIZE of ib->btx_ring
  sungem: another error printed one too early
  ISDN: fix sc/shmem printk format warning
  SMSC: timeout reaches -1
  smsc9420: handle magic field of ethtool_eeprom
  sundance: missing parentheses?
  smsc9420: fix another postfixed timeout
  wimax/i2400m: driver loads firmware v1.4 instead of v1.3
  vlan: Update skb->mac_header in __vlan_put_tag().
  cxgb3: Add support for PCI ID 0x35.
  tcp: remove obsoleted comment about different passes
  TG3: &&/|| confusion
  ATM: misplaced parentheses?
  net/mv643xx: don't disable the mib timer too early and lock properly
  net/mv643xx: use GFP_ATOMIC while atomic
  atl1c: Atheros L1C Gigabit Ethernet driver
  net: Kill skb_truesize_check(), it only catches false-positives.
  net: forcedeth: Fix wake-on-lan regression

10 years agoLinux 2.6.29-rc6
Linus Torvalds [Mon, 23 Feb 2009 04:19:40 +0000]
Linux 2.6.29-rc6

10 years agoacpi/doc: add missing param value
Randy Dunlap [Mon, 23 Feb 2009 01:05:22 +0000]
acpi/doc: add missing param value

Add missing parameter value to list of available values
for acpi=<value>.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agonetns: Remove net_alive
Eric W. Biederman [Sun, 22 Feb 2009 08:11:09 +0000]
netns: Remove net_alive

It turns out that net_alive is unnecessary, and the original problem
that led to it being added was simply that the icmp code thought
it was a network device and wound up being unable to handle packets
while there were still packets in the network namespace.

Now that icmp and tcp have been fixed to properly register themselves
this problem is no longer present and we have a stronger guarantee
that packets will not arrive in a network namespace then that provided
by net_alive in netif_receive_skb.  So remove net_alive allowing
packet reception run a little faster.

Additionally document the strong reason why network namespace cleanup
is safe so that if something happens again someone else will have
a chance of figuring it out.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agotcp: Like icmp use register_pernet_subsys
Eric W. Biederman [Sun, 22 Feb 2009 08:10:18 +0000]
tcp: Like icmp use register_pernet_subsys

To remove the possibility of packets flying around when network
devices are being cleaned up use reisger_pernet_subsys instead of
register_pernet_device.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agonetns: Fix icmp shutdown.
Eric W. Biederman [Sun, 22 Feb 2009 08:09:14 +0000]
netns: Fix icmp shutdown.

Recently I had a kernel panic in icmp_send during a network namespace
cleanup.  There were packets in the arp queue that failed to be sent
and we attempted to generate an ICMP host unreachable message, but
failed because icmp_sk_exit had already been called.

The network devices are removed from a network namespace and their
arp queues are flushed before we do attempt to shutdown subsystems
so this error should have been impossible.

It turns out icmp_init is using register_pernet_device instead
of register_pernet_subsys.  Which resulted in icmp being shut down
while we still had the possibility of packets in flight, making
a nasty NULL pointer deference in interrupt context possible.

Changing this to register_pernet_subsys fixes the problem in
my testing.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoipv4: Clean whitespaces in net/ipv4/Kconfig.
Jesper Dangaard Brouer [Sun, 22 Feb 2009 08:07:13 +0000]
ipv4: Clean whitespaces in net/ipv4/Kconfig.

While going through net/ipv4/Kconfig cleanup whitespaces.

Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoipv4: Fix rp_filter description in net/ipv4/Kconfig.
Jesper Dangaard Brouer [Sun, 22 Feb 2009 08:06:20 +0000]
ipv4: Fix rp_filter description in net/ipv4/Kconfig.

The reverse path filter (rp_filter) will NOT get enabled
when enabling forwarding.  Read the code and tested in
in practice.

Most distributions do enable it in startup scripts.

Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agosnap: handle registration error and compile warning
Stephen Hemminger [Sun, 22 Feb 2009 08:03:19 +0000]
snap: handle registration error and compile warning

If this module can't load, it is almost certainly because something else
is already bound to that SAP. So in that case, return the same error code
as other SAP usage, and fail the module load.

Also fixes a compiler warning about printk of non const.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agollc: fix non-const printk warning
Stephen Hemminger [Sun, 22 Feb 2009 08:02:44 +0000]
llc: fix non-const printk warning

Mark some strings as const.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoip: ipip compile warning
Stephen Hemminger [Sun, 22 Feb 2009 08:02:08 +0000]
ip: ipip compile warning

Get rid of compile warning about non-const format

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoip: add loose reverse path filtering
Stephen Hemminger [Fri, 20 Feb 2009 08:25:36 +0000]
ip: add loose reverse path filtering

Extend existing reverse path filter option to allow strict or loose
filtering. (See http://en.wikipedia.org/wiki/Reverse_path_filtering).

For compatibility with existing usage, the value 1 is chosen for strict mode
and 2 for loose mode.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoRevert "etherh: Get working again."
David S. Miller [Mon, 23 Feb 2009 03:54:16 +0000]
Revert "etherh: Get working again."

This reverts commit 7d3d5ec168f1f40e8547d2a1659670ef222a053b.

Russell is going to merge this in via the ARM tree.

Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoMerge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied...
Linus Torvalds [Mon, 23 Feb 2009 00:26:09 +0000]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: Add missing mutex_lock(&dev->struct_mutex)
  drm/i915: fix WC mapping in non-GEM i915 code.
  drm/i915: Fix regression in 95ca9d
  drm/i915: Retire requests from i915_gem_busy_ioctl.
  drm/i915: suspend/resume GEM when KMS is active
  drm/i915: Don't let a device flush to prepare buffers clear new write_domains.
  drm/i915: Cut two args to set_to_gpu_domain that confused this tricky path.

10 years agodrm/i915: Add missing mutex_lock(&dev->struct_mutex)
Pierre Willenbrock [Mon, 23 Feb 2009 00:12:15 +0000]
drm/i915: Add missing mutex_lock(&dev->struct_mutex)

there might be a nicer way to fix this but this is the simplest for now.

Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agodrm/i915: fix WC mapping in non-GEM i915 code.
Jesse Barnes [Mon, 23 Feb 2009 00:08:21 +0000]
drm/i915: fix WC mapping in non-GEM i915 code.

[airlied - taken from mailing list posting]

Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agodrm/i915: Fix regression in 95ca9d
Chris Wilson [Fri, 20 Feb 2009 17:52:20 +0000]
drm/i915: Fix regression in 95ca9d

The object is dereferenced before the NULL check. Oops.

Fixes http://bugs.freedesktop.org/show_bug.cgi?id=20235

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agodrm/i915: Retire requests from i915_gem_busy_ioctl.
Eric Anholt [Wed, 18 Feb 2009 17:44:56 +0000]
drm/i915: Retire requests from i915_gem_busy_ioctl.

This ensures that the user gets the latest information from the hardware
on whether the buffer is busy, potentially reducing the working set of objects
that the user chooses.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agodrm/i915: suspend/resume GEM when KMS is active
Jesse Barnes [Tue, 17 Feb 2009 23:13:31 +0000]
drm/i915: suspend/resume GEM when KMS is active

In the KMS case, we need to suspend/resume GEM as well.  So on suspend, make
sure we idle GEM and stop any new rendering from coming in, and on resume,
re-init the framebuffer and clear the suspended flag.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agodrm/i915: Don't let a device flush to prepare buffers clear new write_domains.
Eric Anholt [Thu, 19 Feb 2009 22:54:51 +0000]
drm/i915: Don't let a device flush to prepare buffers clear new write_domains.

The problem was that object_set_to_gpu_domain would set the new write_domains
that are getting set by this batchbuffer, then the accumulated flushes required
for all the objects in preparation for this batchbuffer were posted, and the
brand new write domain would get cleared by the flush being posted.  Instead,
hang on to the new (or old if we're not changing it) value and set it after
the flush is queued.

Results from this noticably included conformance test failures from reads
shortly after writes (where the new write domain had been lost and thus not
flushed and waited on), but is a suspected cause of hangs in some apps when
a write domain is lost on a buffer that gets reused for instruction or
commmand state.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agodrm/i915: Cut two args to set_to_gpu_domain that confused this tricky path.
Eric Anholt [Thu, 19 Feb 2009 22:40:50 +0000]
drm/i915: Cut two args to set_to_gpu_domain that confused this tricky path.

While not strictly required, it helped while thinking about the following
change.  This change should be invariant.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

10 years agoselinux: Fix the NetLabel glue code for setsockopt()
Paul Moore [Fri, 20 Feb 2009 21:33:02 +0000]
selinux: Fix the NetLabel glue code for setsockopt()

At some point we (okay, I) managed to break the ability for users to use the
setsockopt() syscall to set IPv4 options when NetLabel was not active on the
socket in question.  The problem was noticed by someone trying to use the
"-R" (record route) option of ping:

 # ping -R 10.0.0.1
 ping: record route: No message of desired type

The solution is relatively simple, we catch the unlabeled socket case and
clear the error code, allowing the operation to succeed.  Please note that we
still deny users the ability to override IPv4 options on socket's which have
NetLabel labeling active; this is done to ensure the labeling remains intact.

Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>

10 years agocipso: Fix documentation comment
Paul Moore [Fri, 20 Feb 2009 21:32:55 +0000]
cipso: Fix documentation comment

The CIPSO protocol engine incorrectly stated that the FIPS-188 specification
could be found in the kernel's Documentation directory.  This patch corrects
that by removing the comment and directing users to the FIPS-188 documented
hosted online.  For the sake of completeness I've also included a link to the
CIPSO draft specification on the NetLabel website.

Thanks to Randy Dunlap for spotting the error and letting me know.

Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>

10 years agoMerge branch 'core/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux...
Linus Torvalds [Sun, 22 Feb 2009 21:26:30 +0000]
Merge branch 'core/urgent' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'core/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  PM: Split up sysdev_[suspend|resume] from device_power_[down|up], fix

10 years agoPM: Split up sysdev_[suspend|resume] from device_power_[down|up], fix
Ingo Molnar [Sun, 22 Feb 2009 21:07:03 +0000]
PM: Split up sysdev_[suspend|resume] from device_power_[down|up], fix

Impact: module build fix

Fix:

 ERROR: "sysdev_resume" [arch/x86/kernel/apm.ko] undefined!
 ERROR: "sysdev_suspend" [arch/x86/kernel/apm.ko] undefined!

As these APIs are now used by the APM driver, which can be built
as a module.

Also fix a few extra (and inconsistent) newlines in comment blocks
preceding these functions.

Signed-off-by: Ingo Molnar <mingo@elte.hu>

10 years agodocbook: split kernel-api for device-drivers
Randy Dunlap [Sun, 22 Feb 2009 20:15:45 +0000]
docbook: split kernel-api for device-drivers

The kernel-api docbook was much larger than any of the others,
so processing it took longer and needed some docbook extras in
some cases, so split it into kernel-api (infrastructure etc.)
and device drivers/device subsystems.  This allows these docbooks
to be generated in parallel.  (This reduced the docbook processing
time on my 4-proc system with make -j4 from about 5min:16sec to
about 2min:01sec.)

The chapters that were moved from kernel-api to device-drivers are:

Driver Basics
Device drivers infrastructure
Parallel Port Devices
Message-based devices
Sound Devices
16x50 UART Driver
Frame Buffer Library
Input Subsystem
Serial Peripheral Interface (SPI)
I2C and SMBus Subsystem

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoPM: Split up sysdev_[suspend|resume] from device_power_[down|up]
Rafael J. Wysocki [Sun, 22 Feb 2009 17:38:50 +0000]
PM: Split up sysdev_[suspend|resume] from device_power_[down|up]

Move the sysdev_suspend/resume from the callee to the callers, with
no real change in semantics, so that we can rework the disabling of
interrupts during suspend/hibernation.

This is based on an earlier patch from Linus.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agox86: Add IRQF_TIMER to legacy x86 timer interrupt descriptors
Linus Torvalds [Sun, 22 Feb 2009 18:27:49 +0000]
x86: Add IRQF_TIMER to legacy x86 timer interrupt descriptors

Right now nobody cares, but the suspend/resume code will eventually want
to suspend device interrupts without suspending the timer, and will
depend on this flag to know.

The modern x86 timer infrastructure uses the local APIC timers and never
shows up as a device interrupt at all, so it isn't affected and doesn't
need any of this.

Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoMerge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux...
Linus Torvalds [Sun, 22 Feb 2009 17:28:46 +0000]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: remove CONFIG_ACPI_SYSTEM
  fujitsu-laptop: Use RFKILL support bitmask from firmware
  x86_64: Fix S3 fail path
  x86_64: acpi/wakeup_64 cleanup
  battery: don't assume we are fully charged when not charging or discharging
  ACPI: EC: Add delay for slow MSI controller

10 years agoPATCH [2/2] Documentation/filesystems/sysfs.txt: fix descriptions of device attributes
Mike Murphy [Sun, 22 Feb 2009 06:19:23 +0000]
PATCH [2/2] Documentation/filesystems/sysfs.txt: fix descriptions of device attributes

Fix descriptions of device attributes to be consistent with the actual
implementations in include/linux/device.h

Signed-off-by: Mike Murphy <mamurph[at]cs.clemson.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoPATCH [1/2] Documentation/driver-model/device.txt: fix struct device_attribute
Mike Murphy [Sun, 22 Feb 2009 06:17:14 +0000]
PATCH [1/2] Documentation/driver-model/device.txt: fix struct device_attribute

Fix the presented definition of struct device_attribute to match the
actual definition in include/linux/device.h

Signed-off-by: Mike Murphy <mamurph[at]cs.clemson.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agom68k: atari - Rename "mfp" to "st_mfp"
Geert Uytterhoeven [Sun, 22 Feb 2009 08:38:47 +0000]
m68k: atari - Rename "mfp" to "st_mfp"

http://kisskb.ellerman.id.au/kisskb/buildresult/72115/:
| net/mac80211/ieee80211_i.h:327: error: syntax error before 'volatile'
| net/mac80211/ieee80211_i.h:350: error: syntax error before '}' token
| net/mac80211/ieee80211_i.h:455: error: field 'sta' has incomplete type
| distcc[19430] ERROR: compile net/mac80211/main.c on sprygo/32 failed

This is caused by

| # define mfp ((*(volatile struct MFP*)MFP_BAS))

in arch/m68k/include/asm/atarihw.h, which conflicts with the new "mfp" enum in
net/mac80211/ieee80211_i.h.

Rename "mfp" to "st_mfp", as it's a way too generic name for a global #define.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agonetns: fix double free at netns creation
Daniel Lezcano [Sun, 22 Feb 2009 08:07:53 +0000]
netns: fix double free at netns creation

This patch fix a double free when a network namespace fails.
The previous code does a kfree of the net_generic structure when
one of the init subsystem initialization fails.
The 'setup_net' function does kfree(ng) and returns an error.
The caller, 'copy_net_ns', call net_free on error, and this one
calls kfree(net->gen), making this pointer freed twice.

This patch make the code symetric, the net_alloc does the net_generic
allocation and the net_free frees the net_generic.

Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoveth : add the set_mac_address capability
Daniel Lezcano [Sun, 22 Feb 2009 08:04:45 +0000]
veth : add the set_mac_address capability

Fix lost set_mac_address capability.

Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agotcp: Always set urgent pointer if it's beyond snd_nxt
Herbert Xu [Sun, 22 Feb 2009 07:52:29 +0000]
tcp: Always set urgent pointer if it's beyond snd_nxt

Our TCP stack does not set the urgent flag if the urgent pointer
does not fit in 16 bits, i.e., if it is more than 64K from the
sequence number of a packet.

This behaviour is different from the BSDs, and clearly contradicts
the purpose of urgent mode, which is to send the notification
(though not necessarily the associated data) as soon as possible.
Our current behaviour may in fact delay the urgent notification
indefinitely if the receiver window does not open up.

Simply matching BSD however may break legacy applications which
incorrectly rely on the out-of-band delivery of urgent data, and
conversely the in-band delivery of non-urgent data.

Alexey Kuznetsov suggested a safe solution of following BSD only
if the urgent pointer itself has not yet been transmitted.  This
way we guarantee that when the remote end sees the packet with
non-urgent data marked as urgent due to wrap-around we would have
advanced the urgent pointer beyond, either to the actual urgent
data or to an as-yet untransmitted packet.

The only potential downside is that applications on the remote
end may see multiple SIGURG notifications.  However, this would
occur anyway with other TCP stacks.  More importantly, the outcome
of such a duplicate notification is likely to be harmless since
the signal itself does not carry any information other than the
fact that we're in urgent mode.

Thanks to Ilpo Järvinen for fixing a critical bug in this and
Jeff Chua for reporting that bug.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agosunlance: Beyond ARRAY_SIZE of ib->btx_ring
Roel Kluin [Sun, 22 Feb 2009 07:46:36 +0000]
sunlance: Beyond ARRAY_SIZE of ib->btx_ring

Do not go beyond ARRAY_SIZE of ib->btx_ring

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoetherh: Get working again.
Russell King [Sun, 22 Feb 2009 07:41:57 +0000]
etherh: Get working again.

Further to a71558d, this is round five of fixes to make etherh work
again. As mainline kernels stand, the fixes in b9a9b4b were the wrong
approach.

The 8390 driver was structured by Al Viro to allow the flexibility required
by platforms.  lib8390.c contains the core code which drivers explicitly
include:
- 8390.c includes lib8390.c to provide the standard ISA based driver.
- etherh.c includes it with the accessors defined for RiscPC platforms,
  where it is addressed via the MMIO accessors with a device dependent
  register spacing.

Other platform drivers do something similar.

However, b9a9b4b caused the kernel to contain not only the etherh private
build of lib8390 (included in etherh.c) but also lib8390.c itself, and
referred the new net_device_ops methods to the ISA version.  The result
of this is is not pretty:

Unable to handle kernel paging request at virtual address 12032030
pgd = c8330000
[12032030] *pgd=00000000
Internal error: Oops: 18331805 [#1]
Modules linked in: ipv6
CPU: 0    Not tainted  (2.6.29-rc3 #167)
PC is at do_set_multicast_list+0xd0/0x190
LR is at bitrev32+0x28/0x34
pc : [<c017aab4>]    lr : [<c0139120>]    psr: a0000093
sp : c8321d9c  ip : c8321d84  fp : c8321dbc
r10: c80c6800  r9 : 00000000  r8 : c80c6b60
r7 : c80c6b80  r6 : cc80c800  r5 : c80c6800  r4 : 00000000
r3 : cc80c80c  r2 : 00000004  r1 : 00000007  r0 : e0000000
Flags: NzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
...

Fix up b9a9b4b by making etherh's net_device_ops refer to the internal
lib8390 functions, and remove the build of the ISA 8390.c driver.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoipv6: fix sparse warning: Using plain integer as NULL pointer
Hannes Eder [Sun, 22 Feb 2009 07:37:10 +0000]
ipv6: fix sparse warning: Using plain integer as NULL pointer

Fix this sparse warning:
  net/ipv6/xfrm6_state.c:72:26: warning: Using plain integer as NULL pointer

Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoMerge branches 'release', 'bugzilla-12011', 'bugzilla-12632', 'misc' and 'suspend...
Len Brown [Sun, 22 Feb 2009 03:01:43 +0000]
Merge branches 'release', 'bugzilla-12011', 'bugzilla-12632', 'misc' and 'suspend' into release

10 years agoACPI: remove CONFIG_ACPI_SYSTEM
Bjorn Helgaas [Thu, 19 Feb 2009 19:56:16 +0000]
ACPI: remove CONFIG_ACPI_SYSTEM

Remove CONFIG_ACPI_SYSTEM.  It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".

Some things under CONFIG_ACPI_SYSTEM (acpi_irq_handled, acpi_os_gpe_count(),
event_is_open, register_acpi_notifier(), etc.) are used unconditionally
by the CA, the OSPM, and drivers, so we depend on them always being
present.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

10 years agofujitsu-laptop: Use RFKILL support bitmask from firmware
Tony Vroon [Mon, 2 Feb 2009 11:11:10 +0000]
fujitsu-laptop: Use RFKILL support bitmask from firmware

Up until now, we polled the rfkill status for every incoming FUJ02E3 ACPI event.
It turns out that the firmware has a bitmask which indicates what rfkill-related
state it can report.
The rfkill_supported bitmask is now used to avoid polling for rfkill at all in
the notification handler if there is no support. Also, it is used in the platform
device callbacks. As before we register all callbacks and report "unknown" if the
firmware does not give us status updates for that particular bit.

This was fed through checkpatch.pl and tested on the S6420, S7020 and P8010
platforms.

Signed-off-by: Tony Vroon <tony@linx.net>
Tested-by: Stephen Gildea <stepheng+linux@gildea.com>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>

10 years agox86_64: Fix S3 fail path
Jiri Slaby [Sun, 15 Feb 2009 21:46:45 +0000]
x86_64: Fix S3 fail path

As acpi_enter_sleep_state can fail, take this into account in
do_suspend_lowlevel and don't return to the do_suspend_lowlevel's
caller. This would break (currently) fpu status and preempt count.

Technically, this means use `call' instead of `jmp' and `jmp' to
the `resume_point' after the `call' (i.e. if
acpi_enter_sleep_state returns=fails). `resume_point' will handle
the restore of fpu and preempt count gracefully.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>

10 years agox86_64: acpi/wakeup_64 cleanup
Jiri Slaby [Sun, 15 Feb 2009 21:45:49 +0000]
x86_64: acpi/wakeup_64 cleanup

- remove %ds re-set, it's already set in wakeup_long64
- remove double labels and alignment (ENTRY already adds both)
- use meaningful resume point labelname
- skip alignment while jumping from wakeup_long64 to the resume point
- remove .size, .type and unused labels
[v2]
- added ENDPROCs

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>

10 years agoixgbe: fix for 82598 Si errata causing buffer overflow
Don Skidmore [Sat, 21 Feb 2009 23:42:56 +0000]
ixgbe: fix for 82598 Si errata causing buffer overflow

The failure happens when an interrupt occurs and the driver is reading
EICR.  This read will cause a clear-by-read which leads to two TLP
being inserted in the PCIe retry buffer leading to an overflow of the
buffer and corruption of TLPs.

The solution is different depending where the reading of EICR takes place.

For ixgbe_msix_lsc() since we are in MSIX mode and know OCD is enabled a
clear-by-write is done instead of the normal clear-by-read.

For ixgbe_intr() 0xffffffff is written to EIMC before the read, masking the
interrupts.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agoMerge branch 'hibernate'
Linus Torvalds [Sat, 21 Feb 2009 22:17:26 +0000]
Merge branch 'hibernate'

* hibernate:
  PM: Fix suspend_console and resume_console to use only one semaphore
  PM: Wait for console in resume
  PM: Fix pm_notifiers during user mode hibernation
  swsusp: clean up shrink_all_zones()
  swsusp: dont fiddle with swappiness
  PM: fix build for CONFIG_PM unset
  PM/hibernate: fix "swap breaks after hibernation failures"
  PM/resume: wait for device probing to finish
  Consolidate driver_probe_done() loops into one place

10 years agoPM: Fix suspend_console and resume_console to use only one semaphore
Arve Hjønnevåg [Sat, 14 Feb 2009 01:07:24 +0000]
PM: Fix suspend_console and resume_console to use only one semaphore

This fixes a race where a thread acquires the console while the
console is suspended, and the console is resumed before this
thread releases it. In this case, the secondary console
semaphore would be left locked, and the primary semaphore would
be released twice. This in turn would cause the console switch
on suspend or resume to hang forever.

Note that suspend_console does not actually lock the console
for clients that use acquire_console_sem, it only locks it for
clients that use try_acquire_console_sem. If we change
suspend_console to fully lock the console, then the kernel
may deadlock on suspend. One client of try_acquire_console_sem
is acquire_console_semaphore_for_printk, which uses it to
prevent printk from using the console while it is suspended.

Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoPM: Wait for console in resume
Arve Hjønnevåg [Sat, 14 Feb 2009 01:06:17 +0000]
PM: Wait for console in resume

Avoids later waking up to a blinking cursor if the device woke up and
returned to sleep before the console switch happened.

Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoPM: Fix pm_notifiers during user mode hibernation
Andrey Borzenkov [Sat, 14 Feb 2009 01:05:14 +0000]
PM: Fix pm_notifiers during user mode hibernation

Snapshot device is opened with O_RDONLY during suspend and O_WRONLY durig
resume.  Make sure we also call notifiers with correct parameter telling
them what we are really doing.

Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoswsusp: clean up shrink_all_zones()
Johannes Weiner [Sat, 14 Feb 2009 01:04:10 +0000]
swsusp: clean up shrink_all_zones()

Move local variables to innermost possible scopes and use local
variables to cache calculations/reads done more than once.

No change in functionality (intended).

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoswsusp: dont fiddle with swappiness
Johannes Weiner [Sat, 14 Feb 2009 01:03:08 +0000]
swsusp: dont fiddle with swappiness

sc.swappiness is not used in the swsusp memory shrinking path, do not
set it.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoPM: fix build for CONFIG_PM unset
Rafael J. Wysocki [Sat, 14 Feb 2009 01:02:16 +0000]
PM: fix build for CONFIG_PM unset

Compilation of kprobes.c with CONFIG_PM unset is broken due to some broken
config dependncies.  Fix that.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoPM/hibernate: fix "swap breaks after hibernation failures"
Alan Jenkins [Sat, 14 Feb 2009 01:01:14 +0000]
PM/hibernate: fix "swap breaks after hibernation failures"

http://bugzilla.kernel.org/show_bug.cgi?id=12239

The image writing code dropped a reference to the current swap device.
This doesn't show up if the hibernation succeeds - because it doesn't
affect the image which gets resumed.  But it means multiple _failed_
hibernations end up freeing the swap device while it is still use!

swsusp_write() finds the block device for the swap file using swap_type_of().
It then uses blkdev_get() / blkdev_put() to open and close the block device.

Unfortunately, blkdev_get() assumes ownership of the inode of the block_device
passed to it.  So blkdev_put() calls iput() on the inode.  This is by design
and other callers expect this behaviour.  The fix is for swap_type_of() to take
a reference on the inode using bdget().

Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoPM/resume: wait for device probing to finish
Arjan van de Ven [Sat, 14 Feb 2009 01:00:19 +0000]
PM/resume: wait for device probing to finish

the resume code does not currently wait for device probing to finish.
Even without async function calls this is dicey and not correct,
but with async function calls during the boot sequence this is going
to get hit more...

This patch adds the synchronization using the newly introduced helper.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoConsolidate driver_probe_done() loops into one place
Arjan van de Ven [Sat, 14 Feb 2009 00:59:06 +0000]
Consolidate driver_probe_done() loops into one place

there's a few places that currently loop over driver_probe_done(), and
I'm about to add another one. This patch abstracts it into a helper
to reduce duplication.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agobattery: don't assume we are fully charged when not charging or discharging
Richard Hughes [Sun, 25 Jan 2009 15:05:50 +0000]
battery: don't assume we are fully charged when not charging or discharging

On hardware like the T61 it can take a couple of seconds for the battery
to start charging after the power is connected, and we incorrectly tell
userspace that we are fully charged, and then go back to charging.

Only mark a battery as fully charged when the preset charge matches either
the last full charge, or the design charge.

http://bugzilla.kernel.org/show_bug.cgi?id=12632

Signed-off-by: Richard Hughes <hughsient@gmail.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>

10 years agoACPI: EC: Add delay for slow MSI controller
Alexey Starikovskiy [Sat, 21 Feb 2009 17:18:13 +0000]
ACPI: EC: Add delay for slow MSI controller

http://bugzilla.kernel.org/show_bug.cgi?id=12011

Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>

10 years agoMerge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Sat, 21 Feb 2009 17:15:39 +0000]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, mce: remove incorrect __cpuinit for mce_cpu_features()
  MAINTAINERS: paravirt-ops maintainers update

10 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6
Linus Torvalds [Sat, 21 Feb 2009 17:11:28 +0000]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] Fix multiuser mounts so server does not invalidate earlier security contexts
  [CIFS] improve posix semantics of file create
  [CIFS] Fix oops in cifs_strfromUCS_le mounting to servers which do not specify their OS
  cifs: posix fill in inode needed by posix open
  cifs: properly handle case where CIFSGetSrvInodeNumber fails
  cifs: refactor new_inode() calls and inode initialization
  [CIFS] Prevent OOPs when mounting with remote prefixpath.
  [CIFS] ipv6_addr_equal for address comparison

10 years agonet: kernel panic in dev_hard_start_xmit: remove faulty software TX time stamping
Patrick Ohly [Sat, 21 Feb 2009 10:42:18 +0000]
net: kernel panic in dev_hard_start_xmit: remove faulty software TX time stamping

The current implementation of the TX software time stamping fallback is
faulty because it accesses the skb after ndo_start_xmit() returns
successfully. This patch removes the fallback, which fixes kernel panics
seen during stress tests. Hardware time stamping is not affected by this
removal.

Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agox86, mce: remove incorrect __cpuinit for mce_cpu_features()
H. Peter Anvin [Sat, 21 Feb 2009 07:35:51 +0000]
x86, mce: remove incorrect __cpuinit for mce_cpu_features()

Impact: Bug fix on UP

Checkin 6ec68bff3c81e776a455f6aca95c8c5f1d630198:
    x86, mce: reinitialize per cpu features on resume

introduced a call to mce_cpu_features() in the resume path, in order
for the MCE machinery to get properly reinitialized after a resume.
However, this function (and its successors) was flagged __cpuinit,
which becomes __init on UP configurations (on SMP suspend/resume
requires CPU hotplug and so this would not be seen.)

Remove the offending __cpuinit annotations for mce_cpu_features() and
its successor functions.

Cc: Andi Kleen <ak@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

10 years ago[CIFS] Fix multiuser mounts so server does not invalidate earlier security contexts
Steve French [Fri, 20 Feb 2009 05:43:09 +0000]
[CIFS] Fix multiuser mounts so server does not invalidate earlier security contexts

When two different users mount the same Windows 2003 Server share using CIFS,
the first session mounted can be invalidated.  Some servers invalidate the first
smb session when a second similar user (e.g. two users who get mapped by server to "guest")
authenticates an smb session from the same client.

By making sure that we set the 2nd and subsequent vc numbers to nonzero values,
this ensures that we will not have this problem.

Fixes Samba bug 6004, problem description follows:
How to reproduce:

- configure an "open share" (full permissions to Guest user) on Windows 2003
Server (I couldn't reproduce the problem with Samba server or Windows older
than 2003)
- mount the share twice with different users who will be authenticated as guest.

 noacl,noperm,user=john,dir_mode=0700,domain=DOMAIN,rw
 noacl,noperm,user=jeff,dir_mode=0700,domain=DOMAIN,rw

Result:

- just the mount point mounted last is accessible:

Signed-off-by: Steve French <sfrench@us.ibm.com>

10 years ago[CIFS] improve posix semantics of file create
Steve French [Fri, 20 Feb 2009 04:32:45 +0000]
[CIFS] improve posix semantics of file create

Samba server added support for a new posix open/create/mkdir operation
a year or so ago, and we added support to cifs for mkdir to use it,
but had not added the corresponding code to file create.

The following patch helps improve the performance of the cifs create
path (to Samba and servers which support the cifs posix protocol
extensions).  Using Connectathon basic test1, with 2000 files, the
performance improved about 15%, and also helped reduce network traffic
(17% fewer SMBs sent over the wire) due to saving a network round trip
for the SetPathInfo on every file create.

It should also help the semantics (and probably the performance) of
write (e.g. when posix byte range locks are on the file) on file
handles opened with posix create, and adds support for a few flags
which would have to be ignored otherwise.

Signed-off-by: Steve French <sfrench@us.ibm.com>

10 years ago[CIFS] Fix oops in cifs_strfromUCS_le mounting to servers which do not specify their OS
Steve French [Tue, 17 Feb 2009 01:29:40 +0000]
[CIFS] Fix oops in cifs_strfromUCS_le mounting to servers which do not specify their OS

Fixes kernel bug #10451 http://bugzilla.kernel.org/show_bug.cgi?id=10451

Certain NAS appliances do not set the operating system or network operating system
fields in the session setup response on the wire.  cifs was oopsing on the unexpected
zero length response fields (when trying to null terminate a zero length field).

This fixes the oops.

Acked-by: Jeff Layton <jlayton@redhat.com>
CC: stable <stable@kernel.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>

10 years agocifs: posix fill in inode needed by posix open
Jeff Layton [Wed, 11 Feb 2009 13:08:28 +0000]
cifs: posix fill in inode needed by posix open

function needed to prepare for posix open

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

10 years agocifs: properly handle case where CIFSGetSrvInodeNumber fails
Jeff Layton [Wed, 11 Feb 2009 13:08:26 +0000]
cifs: properly handle case where CIFSGetSrvInodeNumber fails

...if it does then we pass a pointer to an unintialized variable for
the inode number to cifs_new_inode. Have it pass a NULL pointer instead.

Also tweak the function prototypes to reduce the amount of casting.

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

10 years agocifs: refactor new_inode() calls and inode initialization
Jeff Layton [Tue, 10 Feb 2009 12:33:57 +0000]
cifs: refactor new_inode() calls and inode initialization

Move new inode creation into a separate routine and refactor the
callers to take advantage of it.

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>