9 years agopxa168_eth: remove unneeded null check
Dan Carpenter [Tue, 24 Aug 2010 06:52:46 +0000]
pxa168_eth: remove unneeded null check

"pep->pd" isn't checked consistently in this function.  For example it's
dereferenced unconditionally on the next line after the end of the if
condition.  This function is only called from pxa168_eth_probe() and
pep->pd is always non-NULL so I removed the check.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agophylib: Fix race between returning phydev and calling adjust_link
Anton Vorontsov [Tue, 24 Aug 2010 21:46:12 +0000]
phylib: Fix race between returning phydev and calling adjust_link

It is possible that phylib will call adjust_link before returning
from {,of_}phy_connect(), which may cause the following [very rare,
though] oops upon reopening the device:

  Unable to handle kernel paging request for data at address 0x0000024c
  Oops: Kernel access of bad area, sig: 11 [#1]
  PREEMPT SMP NR_CPUS=2 LTT NESTING LEVEL : 0
  P1021 RDB
  Modules linked in:
  NIP: c0345dac LR: c0345dac CTR: c0345d84
  TASK = dffab6b0[30] 'events/0' THREAD: c0d24000 CPU: 0
  [...]
  NIP [c0345dac] adjust_link+0x28/0x19c
  LR [c0345dac] adjust_link+0x28/0x19c
  Call Trace:
  [c0d25f00] [000045e1] 0x45e1 (unreliable)
  [c0d25f30] [c036c158] phy_state_machine+0x3ac/0x554
  [...]

Here is why. Drivers store phydev in their private structures, e.g.
gianfar driver:

static int init_phy(struct net_device *dev)
{
...
priv->phydev = of_phy_connect(...);
...
}

So that adjust_link could retrieve it back:

static void adjust_link(struct net_device *dev)
{
...
struct phy_device *phydev = priv->phydev;
...
}

If the device has been opened before, then phydev->state is set to
PHY_HALTED (or undefined if the driver didn't call phy_stop()).

Now, phy_connect starts the PHY state machine before returning phydev to
the driver:

phy_start_machine(phydev, NULL);

if (phydev->irq > 0)
phy_start_interrupts(phydev);

return phydev;

The time between 'phy_start_machine()' and 'return phydev' is undefined.
The start machine routine delays execution for 1 second, which is enough
for most cases. But under heavy load, or if you're unlucky, it is quite
possible that PHY state machine will execute before phy_connect()
returns, and so adjust_link callback will try to dereference phydev,
which is not yet ready.

To fix the issue, simply initialize the PHY's state to PHY_READY during
phy_attach(). This will ensure that phylib won't call adjust_link before
phy_start().

Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agocaif-driver: add HAS_DMA dependency
Heiko Carstens [Tue, 24 Aug 2010 19:21:13 +0000]
caif-driver: add HAS_DMA dependency

Fix this error on an s390 allyesconfig build:

linux-2.6/drivers/net/caif/caif_spi.c:98:
    undefined reference to `dma_free_coherent'

Cc: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years ago3c59x: Fix deadlock between boomerang_interrupt and boomerang_start_tx
Neil Horman [Wed, 11 Aug 2010 05:12:57 +0000]
3c59x: Fix deadlock between boomerang_interrupt and boomerang_start_tx

If netconsole is in use, there is a possibility for deadlock in 3c59x between
boomerang_interrupt and boomerang_start_xmit.  Both routines take the vp->lock,
and if netconsole is in use, a pr_* call from the boomerang_interrupt routine
will result in the netconsole code attempting to trnasmit an skb, which can try
to take the same spin lock, resulting in deadlock.

The fix is pretty straightforward.  This patch allocats a bit in the 3c59x
private structure to indicate that its handling an interrupt.  If we get into
the transmit routine and that bit is set, we can be sure that we have recursed
and will deadlock if we continue, so instead we just return NETDEV_TX_BUSY, so
the stack requeues the skb to try again later.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoqlcnic: fix poll implementation
Yinglin Luan [Sun, 22 Aug 2010 21:57:56 +0000]
qlcnic: fix poll implementation

Function qlcnic_intr has pointer to qlcnic_host_sds_ring
as second parameter not pointer to qlcnic_adapter.

Signed-off-by: Yinglin Luan <synmyth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonetxen: fix poll implementation
Yinglin Luan [Sun, 22 Aug 2010 21:56:19 +0000]
netxen: fix poll implementation

Function netxen_intr has pointer to nx_host_sds_ring
as second parameter not pointer to netxen_adapter.

Signed-off-by: Yinglin Luan <synmyth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agobridge: netfilter: fix a memory leak
Changli Gao [Sun, 22 Aug 2010 19:03:26 +0000]
bridge: netfilter: fix a memory leak

nf_bridge_alloc() always reset the skb->nf_bridge, so we should always
put the old one.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonetfilter: fix CONFIG_COMPAT support
Florian Westphal [Mon, 23 Aug 2010 21:41:22 +0000]
netfilter: fix CONFIG_COMPAT support

commit f3c5c1bfd430858d3a05436f82c51e53104feb6b
(netfilter: xtables: make ip_tables reentrant) forgot to
also compute the jumpstack size in the compat handlers.

Result is that "iptables -I INPUT -j userchain" turns into -j DROP.

Reported by Sebastian Roesner on #netfilter, closes
http://bugzilla.netfilter.org/show_bug.cgi?id=669.

Note: arptables change is compile-tested only.

Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoisdn/avm: fix build when PCMCIA is not enabled
Randy Dunlap [Thu, 19 Aug 2010 07:07:23 +0000]
isdn/avm: fix build when PCMCIA is not enabled

Why wouldn't kconfig symbol ISDN_DRV_AVMB1_B1PCMCIA also depend on
PCMCIA?

Fix build for PCMCIA not enabled:

ERROR: "b1_free_card" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined!
ERROR: "b1ctl_proc_fops" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined!
ERROR: "b1_reset_ctr" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined!
ERROR: "b1_load_firmware" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined!
ERROR: "b1_send_message" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined!
ERROR: "b1_release_appl" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined!
ERROR: "b1_register_appl" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined!
ERROR: "b1_getrevision" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined!
ERROR: "b1_detect" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined!
ERROR: "b1_interrupt" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined!
ERROR: "b1_alloc_card" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined!

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Carsten Paeth <calle@calle.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoheader: fix broken headers for user space
Changli Gao [Sun, 22 Aug 2010 17:25:05 +0000]
header: fix broken headers for user space

__packed is only defined in kernel space, so we should use
__attribute__((packed)) for the code shared between kernel and user space.

Two __attribute() annotations are replaced with __attribute__() too.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Thu, 19 Aug 2010 23:54:13 +0000]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

9 years agoe1000e: don't check for alternate MAC addr on parts that don't support it
Bruce Allan [Thu, 19 Aug 2010 22:48:52 +0000]
e1000e: don't check for alternate MAC addr on parts that don't support it

From: Bruce Allan <bruce.w.allan@intel.com>

The alternate MAC address feature is only supported by 80003ES2LAN and
82571 LOMs as well as a couple 82571 mezzanine cards.  Checking for an
alternate MAC address on other parts can fail leading to the driver not
able to load.  This patch limits the check for an alternate MAC address
to be done only for parts that support the feature.

This issue has been around since support for the feature was introduced
to the e1000e driver in 2.6.34.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reported-by: Fabio Varesano <fax8@users.sourceforge.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoe1000e: disable ASPM L1 on 82573
Bruce Allan [Thu, 19 Aug 2010 22:48:30 +0000]
e1000e: disable ASPM L1 on 82573

On the e1000-devel mailing list, Nils Faerber reported latency issues with
the 82573 LOM on a ThinkPad X60.  It was found to be caused by ASPM L1;
disabling it resolves the latency.  The issue is present in kernels back
to 2.6.34 and possibly 2.6.33.

Reported-by: Nils Faerber <nils.faerber@kernelconcepts.de>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoll_temac: Fix poll implementation
Michal Simek [Wed, 18 Aug 2010 00:26:34 +0000]
ll_temac: Fix poll implementation

Functions ll_temac_rx_irq and ll_temac_tx_irq
have pointer to net_device as second parameter not
pointer to temac_local.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonetxen: fix a race in netxen_nic_get_stats()
Eric Dumazet [Wed, 18 Aug 2010 02:29:30 +0000]
netxen: fix a race in netxen_nic_get_stats()

Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoqlnic: fix a race in qlcnic_get_stats()
Eric Dumazet [Wed, 18 Aug 2010 00:42:48 +0000]
qlnic: fix a race in qlcnic_get_stats()

Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoirda: fix a race in irlan_eth_xmit()
Eric Dumazet [Wed, 18 Aug 2010 00:24:43 +0000]
irda: fix a race in irlan_eth_xmit()

After skb is queued, its illegal to dereference it.

Cache skb->len into a temporary variable.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonet: sh_eth: remove unused variable
Kuninori Morimoto [Thu, 19 Aug 2010 07:39:45 +0000]
net: sh_eth: remove unused variable

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonetxen: update version 4.0.74
Amit Kumar Salecha [Tue, 17 Aug 2010 20:51:52 +0000]
netxen: update version 4.0.74

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonetxen: fix inconsistent lock state
Amit Kumar Salecha [Tue, 17 Aug 2010 20:51:51 +0000]
netxen: fix inconsistent lock state

Spin lock rds_ring->lock is used in poll routine, so other users should
use spin_lock_bh(). While posting rx buffers from netxen_nic_attach,
rds_ring->lock is not required, so cleaning it instead of fixing it by
spin_lock_bh().

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agovlan: Match underlying dev carrier on vlan add
Phil Oester [Tue, 17 Aug 2010 18:45:08 +0000]
vlan: Match underlying dev carrier on vlan add

When adding a new vlan, if the underlying interface has no carrier,
then the newly added vlan interface should also have no carrier.
At present, this is not true - the newly added vlan is added with
carrier up.  Fix by checking state of real device.

Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoibmveth: Fix opps during MTU change on an active device
Robert Jennings [Tue, 17 Aug 2010 09:15:45 +0000]
ibmveth: Fix opps during MTU change on an active device

This fixes the following opps which can occur when trying to deallocate
receive buffer pools when changing the MTU of an active ibmveth device.

Oops: Kernel access of bad area, sig: 11 [#1]
NIP: d000000004db00e8 LR: d000000004db00ac CTR: 0000000000591038
REGS: c00000007fff39d0 TRAP: 0300   Not tainted  (2.6.36-rc1)
MSR: 8000000000009032 <EE,ME,IR,DR>  CR: 22248244  XER: 00000002
DAR: 0000000000000488, DSISR: 0000000042000000
TASK = c00000007c463790[6531] 'netserver' THREAD: c00000007a154000 CPU: 0
GPR00: 0000000000000000 c00000007fff3c50 d000000004dbd360 0000000000000001
GPR04: 0000000000000001 1fffffffffffffff 000000000000043c c00000007a8e9f60
GPR08: c00000007a8e9e20 0000000000000245 0000000000000488 0000000000000000
GPR12: 00000000000000c0 c000000006d70000 c00000007bfec098 c00000007bfebc2c
GPR16: c00000007a157c78 0000000000000000 0000000000000001 0000000000000000
GPR20: 0000000000000001 0000000000000010 c000000000b51180 c00000007a8e9d90
GPR24: c00000007a8e9da0 c00000007a8e9580 00000000000005ea 00000000000002ff
GPR28: 0000000000000004 0000000000000080 c000000000a946f8 c00000007a8e9d80
NIP [d000000004db00e8] .ibmveth_remove_buffer_from_pool+0xe8/0x130 [ibmveth]
LR [d000000004db00ac] .ibmveth_remove_buffer_from_pool+0xac/0x130 [ibmveth]
Call Trace:
[c00000007fff3c50] [d000000004db00ac] .ibmveth_remove_buffer_from_pool+0xac/0x130 [ibmveth] (unreliable)
[c00000007fff3cf0] [d000000004db31dc] .ibmveth_poll+0x30c/0x460 [ibmveth]
[c00000007fff3dd0] [c00000000042c4b8] .net_rx_action+0x178/0x278
[c00000007fff3eb0] [c000000000093cf0] .__do_softirq+0x118/0x1f8
[c00000007fff3f90] [c00000000002ab3c] .call_do_softirq+0x14/0x24
[c00000007a157600] [c00000000000e3e4] .do_softirq+0xec/0x110
[c00000007a1576a0] [c000000000093394] .local_bh_enable_ip+0xb4/0xe0
[c00000007a157720] [c0000000004f0bac] ._raw_spin_unlock_bh+0x3c/0x50
[c00000007a157790] [c0000000004186e0] .release_sock+0x158/0x188
[c00000007a157840] [c000000000479660] .tcp_recvmsg+0x560/0x9b8
[c00000007a157970] [c0000000004a0d78] .inet_recvmsg+0x80/0xd8
[c00000007a157a00] [c000000000413e28] .sock_recvmsg+0x128/0x178
[c00000007a157bf0] [c0000000004164ac] .SyS_recvfrom+0xb4/0x148
[c00000007a157d70] [c000000000411f3c] .SyS_socketcall+0x274/0x360
[c00000007a157e30] [c0000000000085b4] syscall_exit+0x0/0x40

Reported-by: Rafael Camarda Silva Folco <rfolco@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoehea: Fix synchronization between HW and SW send queue
Andre Detsch [Tue, 17 Aug 2010 05:49:12 +0000]
ehea: Fix synchronization between HW and SW send queue

ehea: Fix synchronization between HW and SW send queue

When memory is added to / removed from a partition via the Memory DLPAR
mechanism, the eHEA driver has to do a couple of things to reflect the
memory change in its own IO address translation tables. This involves
stopping and restarting the HW queues.
During this operation, it is possible that HW and SW pointer into these
queues get out of sync. This results in a situation where packets that
are attached to a send queue are not transmitted immediately, but
delayed until further X packets have been put on the queue.

This patch detects such loss of synchronization, and resets the ehea
port when needed.

Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agobnx2x: Update bnx2x version to 1.52.53-4
Yaniv Rosner [Mon, 16 Aug 2010 06:34:07 +0000]
bnx2x: Update bnx2x version to 1.52.53-4

Update bnx2x version to 1.52.53-4

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agobnx2x: Fix PHY locking problem
Yaniv Rosner [Mon, 16 Aug 2010 06:34:06 +0000]
bnx2x: Fix PHY locking problem

PHY locking is required between two ports for some external PHYs. Since
initialization was done in the common init function (called only on the
first port initialization) rather than in the port init function, there
was in fact no PHY locking between the ports.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agords: fix a leak of kernel memory
Eric Dumazet [Mon, 16 Aug 2010 03:25:00 +0000]
rds: fix a leak of kernel memory

struct rds_rdma_notify contains a 32 bits hole on 64bit arches,
make sure it is zeroed before copying it to user.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonetlink: fix compat recvmsg
Johannes Berg [Sun, 15 Aug 2010 21:20:44 +0000]
netlink: fix compat recvmsg

Since
commit 1dacc76d0014a034b8aca14237c127d7c19d7726
Author: Johannes Berg <johannes@sipsolutions.net>
Date:   Wed Jul 1 11:26:02 2009 +0000

    net/compat/wext: send different messages to compat tasks

we had a race condition when setting and then
restoring frag_list. Eric attempted to fix it,
but the fix created even worse problems.

However, the original motivation I had when I
added the code that turned out to be racy is
no longer clear to me, since we only copy up
to skb->len to userspace, which doesn't include
the frag_list length. As a result, not doing
any frag_list clearing and restoring avoids
the race condition, while not introducing any
other problems.

Additionally, while preparing this patch I found
that since none of the remaining netlink code is
really aware of the frag_list, we need to use the
original skb's information for packet information
and credentials. This fixes, for example, the
group information received by compat tasks.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@kernel.org [2.6.31+, for 2.6.35 revert 1235f504aa]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonetfilter: fix userspace header warning
Sam Ravnborg [Sun, 15 Aug 2010 10:03:57 +0000]
netfilter: fix userspace header warning

"make headers_check" issued the following warning:

  CHECK   include/linux/netfilter (64 files)
usr/include/linux/netfilter/xt_ipvs.h:19: found __[us]{8,16,32,64} type without #include <linux/types.h>

Fix this by as suggested including linux/types.h.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonet: add Fast Ethernet driver for PXA168.
Sachin Sanap [Fri, 13 Aug 2010 21:22:49 +0000]
net: add Fast Ethernet driver for PXA168.

Signed-off-by: Sachin Sanap <ssanap@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoiwlwifi: use long monitor timer for 5300 series
Wey-Yi Guy [Wed, 18 Aug 2010 19:53:28 +0000]
iwlwifi: use long monitor timer for 5300 series

For 5000 series of devices, use long monitor timer to check
stuck tx queues.

This modification apply to all the 5000 series including 5300 and others.

Cc: stable@kernel.org [2.6.35]
Reported-by: drago01 <drago01@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agodrivers/net/wireless: Restore upper case words in wiphy_<level> messages
Joe Perches [Thu, 12 Aug 2010 02:11:19 +0000]
drivers/net/wireless: Restore upper case words in wiphy_<level> messages

Commit c96c31e499b70964cfc88744046c998bb710e4b8
"(drivers/net/wireless: Use wiphy_<level>)"
inadvertently changed some upper case words to
lower case.  Restore the original case.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agonet: Fix a memmove bug in dev_gro_receive()
Jarek Poplawski [Wed, 11 Aug 2010 02:02:10 +0000]
net: Fix a memmove bug in dev_gro_receive()

>Xin Xiaohui wrote:
> I looked into the code dev_gro_receive(), found the code here:
> if the frags[0] is pulled to 0, then the page will be released,
> and memmove() frags left.
> Is that right? I'm not sure if memmove do right or not, but
> frags[0].size is never set after memove at least. what I think
> a simple way is not to do anything if we found frags[0].size == 0.
> The patch is as followed.
...

This version of the patch fixes the bug directly in memmove.

Reported-by: "Xin, Xiaohui" <xiaohui.xin@intel.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonet sched: fix some kernel memory leaks
Eric Dumazet [Mon, 16 Aug 2010 20:04:22 +0000]
net sched: fix some kernel memory leaks

We leak at least 32bits of kernel memory to user land in tc dump,
because we dont init all fields (capab ?) of the dumped structure.

Use C99 initializers so that holes and non explicit fields are zeroed.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonetfilter: {ip,ip6,arp}_tables: avoid lockdep false positive
Eric Dumazet [Mon, 16 Aug 2010 10:22:10 +0000]
netfilter: {ip,ip6,arp}_tables: avoid lockdep false positive

After commit 24b36f019 (netfilter: {ip,ip6,arp}_tables: dont block
bottom half more than necessary), lockdep can raise a warning
because we attempt to lock a spinlock with BH enabled, while
the same lock is usually locked by another cpu in a softirq context.

Disable again BH to avoid these lockdep warnings.

Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Diagnosed-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoiwlwifi: fix 3945 filter flags
Johannes Berg [Tue, 17 Aug 2010 09:24:01 +0000]
iwlwifi: fix 3945 filter flags

Applying the filter flags directly as done since

commit 3474ad635db371b0d8d0ee40086f15d223d5b6a4
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Thu Apr 29 04:43:05 2010 -0700

    iwlwifi: apply filter flags directly

broke 3945 under some unknown circumstances, as
reported by Alex.

Since I want to keep the direct application of
filter flags on iwlagn, duplicate the code into
both 3945 and agn and remove committing the
RXON that broke things from the 3945 version.

Cc: stable@kernel.org [2.6.35]
Reported-by: Alex Romosan <romosan@sycorax.lbl.gov>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agoipw2100: don't sync status queue entries
John W. Linville [Fri, 13 Aug 2010 22:47:33 +0000]
ipw2100: don't sync status queue entries

These are allocated with pci_alloc_consistent, so calling
pci_dma_sync_single_for_cpu is incorrect usage of the API.  Remove this
misuse and consequently avoid the following backtrace:

WARNING: at lib/dma-debug.c:902 check_sync+0xce/0x43a()
Hardware name: 2373HU6
ipw2100 0000:02:02.0: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x0000000034e88008] [size=8 bytes]
Modules linked in: microcode ipw2100(+) snd_seq_device ppdev libipw nsc_ircc snd_pcm lib80211 video output irda parport_pc cfg80211 parport thinkpad_acpi e1000 iTCO_wdt crc_ccitt snd_timer iTCO_vendor_support snd i2c_i801 pcspkr rfkill soundcore joydev snd_page_alloc yenta_socket radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core [last unloaded: scsi_wait_scan]
Pid: 0, comm: swapper Tainted: G        W   2.6.35-wl+ #8
Call Trace:
 [<c043aa42>] warn_slowpath_common+0x6a/0x7f
 [<c05d252a>] ? check_sync+0xce/0x43a
 [<c043aaca>] warn_slowpath_fmt+0x2b/0x2f
 [<c05d252a>] check_sync+0xce/0x43a
 [<c046189a>] ? print_lock_contention_bug+0x11/0xb2
 [<c05d2b6f>] debug_dma_sync_single_for_cpu+0x47/0x49
 [<c06cbd3c>] ? ehci_irq+0x31/0x331
 [<f82a224a>] ? ipw2100_irq_tasklet+0x24/0x5e9 [ipw2100]
 [<f82a224a>] ? ipw2100_irq_tasklet+0x24/0x5e9 [ipw2100]
 [<f82a221d>] pci_dma_sync_single_for_cpu.clone.1+0x42/0x4b [ipw2100]
 [<f82a23a2>] ipw2100_irq_tasklet+0x17c/0x5e9 [ipw2100]
 [<c043fd87>] tasklet_action+0x78/0xcb
 [<c0440293>] __do_softirq+0xc4/0x183
 [<c044038d>] do_softirq+0x3b/0x5f
 [<c04404d0>] irq_exit+0x3a/0x6d
 [<c0404423>] do_IRQ+0x8b/0x9f
 [<c04038b5>] common_interrupt+0x35/0x3c
 [<c062ecfa>] ? acpi_idle_enter_simple+0xfe/0x13c
 [<c045007b>] ? exit_itimers+0x2d/0x73
 [<c062ecfc>] ? acpi_idle_enter_simple+0x100/0x13c
 [<c070bf10>] cpuidle_idle_call+0x78/0xdc
 [<c040251c>] cpu_idle+0x9b/0xb7
 [<c07b1dd2>] rest_init+0xa6/0xab
 [<c0a4b96d>] start_kernel+0x389/0x38e
 [<c0a4b0c9>] i386_start_kernel+0xc9/0xd0

Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Mon, 16 Aug 2010 20:56:01 +0000]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

9 years agoRevert "netlink: netlink_recvmsg() fix"
David S. Miller [Mon, 16 Aug 2010 06:21:50 +0000]
Revert "netlink: netlink_recvmsg() fix"

This reverts commit 1235f504aaba2ebeabc863fdb3ceac764a317d47.

It causes regressions worse than the problem it was trying
to fix.  Eric will try to solve the problem another way.

Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoipv6: remove sysctl jiffies conversion on gc_elasticity and min_adv_mss
Min Zhang [Sun, 15 Aug 2010 05:42:51 +0000]
ipv6: remove sysctl jiffies conversion on gc_elasticity and min_adv_mss

sysctl output ipv6 gc_elasticity and min_adv_mss as values divided by
HZ. However, they are not in unit of jiffies, since ip6_rt_min_advmss
refers to packet size and ip6_rt_fc_elasticity is used as scaler as in
expire>>ip6_rt_gc_elasticity, so replace the jiffies conversion
handler will regular handler for them.

This has impact on scripts that are currently working assuming the
divide by HZ, will yield different results with this patch in place.

Signed-off-by: Min Zhang <mzhang@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoxfrm: Use GFP_ATOMIC in xfrm_compile_policy
Herbert Xu [Sun, 15 Aug 2010 05:38:09 +0000]
xfrm: Use GFP_ATOMIC in xfrm_compile_policy

As xfrm_compile_policy runs within a read_lock, we cannot use
GFP_KERNEL for memory allocations.

Reported-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoiwlwifi: use long monitor timer to avoid un-necessary reload
Wey-Yi Guy [Fri, 23 Jul 2010 20:19:40 +0000]
iwlwifi: use long monitor timer to avoid un-necessary reload

For 5000 and 6000g2b series of devices, use long monitor timer to check
stuck tx queues.

.6000g2b series device, it is WiFi/BT combo device, there are some cases,
tx queues are not move for a period of time because the WiFi/BT coex.

.5000 series device, it is being reported firmware got reload more
often than necessary, so extend the timer to avoid un-necessary reload.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

9 years agoiwlwifi: long monitor timer
Wey-Yi Guy [Fri, 23 Jul 2010 20:19:39 +0000]
iwlwifi: long monitor timer

Change the name for monitor timer, also adding define for long monitor
timer; long monitor timer can be used for the type of devices require longer
time to determine the uCode is stuck on tx and needed reload.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

9 years agoath5k: disable ASPM L0s for all cards
Maxim Levitsky [Fri, 13 Aug 2010 15:27:28 +0000]
ath5k: disable ASPM L0s for all cards

Atheros PCIe wireless cards handled by ath5k do require L0s disabled.
For distributions shipping with CONFIG_PCIEASPM (this will be enabled
by default in the future in 2.6.36) this will also mean both L1 and L0s
will be disabled when a pre 1.1 PCIe device is detected. We do know L1
works correctly even for all ath5k pre 1.1 PCIe devices though but cannot
currently undue the effect of a blacklist, for details you can read
pcie_aspm_sanity_check() and see how it adjusts the device link
capability.

It may be possible in the future to implement some PCI API to allow
drivers to override blacklists for pre 1.1 PCIe but for now it is
best to accept that both L0s and L1 will be disabled completely for
distributions shipping with CONFIG_PCIEASPM rather than having this
issue present. Motivation for adding this new API will be to help
with power consumption for some of these devices.

Example of issues you'd see:

  - On the Acer Aspire One (AOA150, Atheros Communications Inc. AR5001
    Wireless Network Adapter [168c:001c] (rev 01)) doesn't work well
    with ASPM enabled, the card will eventually stall on heavy traffic
    with often 'unsupported jumbo' warnings appearing. Disabling
    ASPM L0s in ath5k fixes these problems.

  - On the same card you would see a storm of RXORN interrupts
    even though medium is idle.

Credit for root causing and fixing the bug goes to Jussi Kivilinna.

Cc: David Quan <David.Quan@atheros.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agoath9k_htc: load proper firmware for device ID 7015
Rajkumar Manoharan [Fri, 13 Aug 2010 13:06:40 +0000]
ath9k_htc: load proper firmware for device ID 7015

This patch handles the firmware loading properly
for device ID 7015.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agowl1251: fix trigger scan timeout usage
Yuri Kululin [Fri, 13 Aug 2010 09:46:12 +0000]
wl1251: fix trigger scan timeout usage

Use appropriate command (CMD_TRIGGER_SCAN_TO) instead of scan command
(CMD_SCAN) to configure trigger scan timeout.

This was broken in commit 3a98c30f3e8bb1f32b5bcb74a39647b3670de275.

This fix address the bug reported here:

https://bugzilla.kernel.org/show_bug.cgi?id=16554

Cc: stable@kernel.org
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Yuri Kululin <ext-yuri.kululin@nokia.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agoath9k_htc: Fix disconnect issue in HT40 mode.
Vivek Natarajan [Thu, 12 Aug 2010 08:53:28 +0000]
ath9k_htc: Fix disconnect issue in HT40 mode.

Some APs advertise that they may be HT40 capable in the capabilites
but the current operating channel configuration may be only HT20.
This causes disconnection as ath9k_htc sets WLAN_RC_40_FLAG despite
the AP operating in HT20 mode.
Hence set this flag only if the current channel configuration
is HT40 enabled.

Cc: stable@kernel.org
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agoctcm: rename READ/WRITE defines to avoid redefinitions
Ursula Braun [Thu, 12 Aug 2010 01:58:28 +0000]
ctcm: rename READ/WRITE defines to avoid redefinitions

READ/WRITE seems to be a bit too generic for defines in a device
driver. Just rename them to CTCM_READ/CTCM_WRITE to avoid warnings.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoclaw: rename READ/WRITE defines to avoid redefinitions
Heiko Carstens [Thu, 12 Aug 2010 01:58:27 +0000]
claw: rename READ/WRITE defines to avoid redefinitions

READ/WRITE seems to be a bit too generic for defines in a device driver.
Just rename them to READ_CHANNEL/WRITE_CHANNEL which should suffice.

Fixes this:

In file included from drivers/s390/net/claw.c:93:
drivers/s390/net/claw.h:78:1: warning: "WRITE" redefined
In file included from /home2/heicarst/linux-2.6/arch/s390/include/asm/debug.h:12,
                 from drivers/s390/net/claw.c:68:
include/linux/fs.h:156:1: warning: this is the location of the previous definition

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agophylib: available for any speed ethernet
Randy Dunlap [Wed, 11 Aug 2010 13:26:57 +0000]
phylib: available for any speed ethernet

Several gigabit network drivers (SB1250_MAC, TIGON3, FSL, GIANFAR,
UCC_GETH, MV643XX_ETH, XILINX_LL_TEMAC, S6GMAC, STMMAC_ETH, PASEMI_MAC,
and OCTEON_ETHERNET) select PHYLIB.  These drivers are not under
NET_ETHERNET (10/100 mbit), so this warning is generated (long, irrelevant
parts are omitted):

warning: (NET_DSA && NET && EXPERIMENTAL && NET_ETHERNET && !S390 || ... || SB1250_MAC && NETDEVICES && NETDEV_1000 && SIBYTE_SB1xxx_SOC || TIGON3 && NETDEVICES && NETDEV_1000 && PCI || FSL_PQ_MDIO && NETDEVICES && NETDEV_1000 && FSL_SOC || GIANFAR && NETDEVICES && NETDEV_1000 && FSL_SOC || UCC_GETH && NETDEVICES && NETDEV_1000 && QUICC_ENGINE || MV643XX_ETH && NETDEVICES && NETDEV_1000 && (MV64X60 || PPC32 || PLAT_ORION) || XILINX_LL_TEMAC && NETDEVICES && NETDEV_1000 && (PPC || MICROBLAZE) || S6GMAC && NETDEVICES && NETDEV_1000 && XTENSA_VARIANT_S6000 || STMMAC_ETH && NETDEV_1000 && NETDEVICES && CPU_SUBTYPE_ST40 || PASEMI_MAC && NETDEVICES && NETDEV_10000 && PPC_PASEMI && PCI || OCTEON_ETHERNET && STAGING && !STAGING_EXCLUDE_BUILD && CPU_CAVIUM_OCTEON) selects PHYLIB which has unmet direct dependencies (!S390 && NET_ETHERNET)

PHYLIB is used by non-10/100 mbit ethernet drivers, so change the dependencies
to be NETDEVICES instead of NET_ETHERNET.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agocan: add limit for nframes and clean up signed/unsigned variables
Oliver Hartkopp [Wed, 11 Aug 2010 23:12:35 +0000]
can: add limit for nframes and clean up signed/unsigned variables

This patch adds a limit for nframes as the number of frames in TX_SETUP and
RX_SETUP are derived from a single byte multiplex value by default.
Use-cases that would require to send/filter more than 256 CAN frames should
be implemented in userspace for complexity reasons anyway.

Additionally the assignments of unsigned values from userspace to signed
values in kernelspace and vice versa are fixed by using unsigned values in
kernelspace consistently.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reported-by: Ben Hawkes <hawkes@google.com>
Acked-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoath9k_htc: fix panic on packet injection using airbase-ng tool.
Rajkumar Manoharan [Wed, 11 Aug 2010 14:57:43 +0000]
ath9k_htc: fix panic on packet injection using airbase-ng tool.

This should fix the oops which occurs during the packet injection
on monitor interface.

EIP is at ath9k_htc_tx_start+0x69/0x220 [ath9k_htc]
 [<f84dc8ea>] ? invoke_tx_handlers+0xa5a/0xee0 [mac80211]
 [<f82c84f4>] ? ath9k_htc_tx+0x44/0xe0 [ath9k_htc]
 [<f84db7b8>] ? __ieee80211_tx+0xf8/0x190 [mac80211]
 [<f84dce0d>] ? ieee80211_tx+0x9d/0x1a0 [mac80211]
 [<f84dcfac>] ? ieee80211_xmit+0x9c/0x1c0 [mac80211]
 [<f84dd1b5>] ? ieee80211_monitor_start_xmit+0x85/0xb0 [mac80211]
 [<c04c30cd>] ? dev_hard_start_xmit+0x1ad/0x210
 [<c04b97c2>] ? __alloc_skb+0x52/0x130
 [<c04d7cd5>] ? sch_direct_xmit+0x105/0x170
 [<c04c5e9f>] ? dev_queue_xmit+0x37f/0x4b0
 [<c0567e1e>] ? packet_snd+0x21e/0x250
 [<c05684a2>] ? packet_sendmsg+0x32/0x40
 [<c04b4c63>] ? sock_aio_write+0x113/0x130
 [<c0207934>] ? do_sync_write+0xc4/0x100
 [<c0167740>] ? autoremove_wake_function+0x0/0x50
 [<c02f4414>] ? security_file_permission+0x14/0x20
 [<c0207ad4>] ? rw_verify_area+0x64/0xe0
 [<c01e6458>] ? handle_mm_fault+0x338/0x390
 [<c0207cd5>] ? vfs_write+0x185/0x1a0
 [<c058db20>] ? do_page_fault+0x160/0x3a0
 [<c0208512>] ? sys_write+0x42/0x70
 [<c01033ec>] ? syscall_call+0x7/0xb

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agoipw2100: register pm_qos request before registering pci driver
John W. Linville [Wed, 11 Aug 2010 20:11:00 +0000]
ipw2100: register pm_qos request before registering pci driver

It is necessary to call pm_qos_add_request prior to calling
pm_qos_update_request.  It was revealed that ipw2100 has been
doing this wrong since "pm_qos: Get rid of the allocation in
pm_qos_add_request()" (commit 82f682514a5df89ffb3890627eebf0897b7a84ec)
added a WARN that results in the following backtrace:

WARNING: at kernel/pm_qos_params.c:264 pm_qos_update_request+0x5e/0x70()
pm_qos_update_request() called for unknown object
Call Trace:
[<c1024088>] ? warn_slowpath_common+0x78/0xb0
[<c1041c9e>] ? pm_qos_update_request+0x5e/0x70
[<c1041c9e>] ? pm_qos_update_request+0x5e/0x70
[<c1024153>] ? warn_slowpath_fmt+0x33/0x40
[<c1041c9e>] ? pm_qos_update_request+0x5e/0x70
[<f89fe15f>] ? ipw2100_up+0x3f/0xf10 [ipw2100]
[<c11961c9>] ? vsnprintf+0xc9/0x530
[<f89ff36c>] ? ipw2100_net_init+0x2c/0x1c0 [ipw2100]
[<c12f542d>] ? register_netdevice+0x7d/0x3c0
[<f89f9b00>] ? ipw2100_irq_tasklet+0x910/0x9a0 [ipw2100]
[<c12f579f>] ? register_netdev+0x2f/0x40
[<f89fd471>] ? ipw2100_pci_init_one+0xd21/0x1060 [ipw2100]
[<c11a5ebb>] ? local_pci_probe+0xb/0x10
[<c11a6d49>] ? pci_device_probe+0x69/0x90
[<c1224704>] ? driver_probe_device+0x74/0x180
[<c10dd15a>] ? sysfs_create_dir+0x6a/0xb0
[<c1224889>] ? __driver_attach+0x79/0x80
[<c1224810>] ? __driver_attach+0x0/0x80
[<c1223fa2>] ? bus_for_each_dev+0x52/0x80
[<c1224586>] ? driver_attach+0x16/0x20
[<c1224810>] ? __driver_attach+0x0/0x80
[<c122395f>] ? bus_add_driver+0x17f/0x250
[<c11a5ec0>] ? pci_device_shutdown+0x0/0x20
[<c11a6c80>] ? pci_device_remove+0x0/0x40
[<c1224b13>] ? driver_register+0x63/0x120
[<c11a6f96>] ? __pci_register_driver+0x36/0xa0
[<f84f9048>] ? ipw2100_init+0x48/0x67 [ipw2100]
[<c1001122>] ? do_one_initcall+0x32/0x170
[<c1087078>] ? __vunmap+0xb8/0xf0
[<f84f9000>] ? ipw2100_init+0x0/0x67 [ipw2100]
[<c10510c1>] ? sys_init_module+0x161/0x1000
[<c108f847>] ? sys_close+0x67/0xe0
[<c13647c1>] ? syscall_call+0x7/0xb

This patch moves pm_qos_add_request prior to pci_register_driver in
ipw2100 in order to avoid this problem.

Reported-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agopkt_sched: Check .walk and .leaf class handlers
Jarek Poplawski [Tue, 10 Aug 2010 22:31:20 +0000]
pkt_sched: Check .walk and .leaf class handlers

Require qdisc class ops .walk and .leaf for classful qdisc in
register_qdisc(). The checks could be done later insted, but these
ops are really needed and used by most of classful qdiscs.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agopkt_sched: Fix sch_sfq vs tc_modify_qdisc oops
Jarek Poplawski [Tue, 10 Aug 2010 22:31:02 +0000]
pkt_sched: Fix sch_sfq vs tc_modify_qdisc oops

sch_sfq as a classful qdisc needs the .leaf handler. Otherwise, there
is an oops possible in tc_modify_qdisc()/check_loop().

Fixes commit 7d2681a6ff4f9ab5e48d02550b4c6338f1638998

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agocaif-spi: Bugfix SPI_DATA_POS settings were inverted.
Sjur Braendeland [Tue, 10 Aug 2010 07:36:47 +0000]
caif-spi: Bugfix SPI_DATA_POS settings were inverted.

The setting of SPI_DATA_POS depending on CONFIG_CAIF_SPI_SYNC
where inverted.

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agocaif: Bugfix - Increase default headroom size for control channel.
Sjur Braendeland [Tue, 10 Aug 2010 07:36:46 +0000]
caif: Bugfix - Increase default headroom size for control channel.

Headroom size for control channel must be at least 48 bytes in some scenarios.

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonet: make netpoll_rx return bool for !CONFIG_NETPOLL
John W. Linville [Tue, 10 Aug 2010 23:24:41 +0000]
net: make netpoll_rx return bool for !CONFIG_NETPOLL

"netpoll: Use 'bool' for netpoll_rx() return type." missed the case when
CONFIG_NETPOLL is disabled.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Tue, 10 Aug 2010 22:59:38 +0000]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

9 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluet...
John W. Linville [Tue, 10 Aug 2010 18:55:10 +0000]
Merge branch 'master' of git://git./linux/kernel/git/holtmann/bluetooth-2.6

9 years agoBluetooth: Use 3-DH5 payload size for default ERTM max PDU size
Mat Martineau [Thu, 5 Aug 2010 22:54:27 +0000]
Bluetooth: Use 3-DH5 payload size for default ERTM max PDU size

The previous value of 672 for L2CAP_DEFAULT_MAX_PDU_SIZE is based on
the default L2CAP MTU.  That default MTU is calculated from the size
of two DH5 packets, minus ACL and L2CAP b-frame header overhead.

ERTM is used with newer basebands that typically support larger 3-DH5
packets, and i-frames and s-frames have more header overhead.  With
clean RF conditions, basebands will typically attempt to use 1021-byte
3-DH5 packets for maximum throughput.  Adjusting for 2 bytes of ACL
headers plus 10 bytes of worst-case L2CAP headers yields 1009 bytes
of payload.

This PDU size imposes less overhead for header bytes and gives the
baseband the option to choose 3-DH5 packets, but is small enough for
ERTM traffic to interleave well with other L2CAP or SCO data.
672-byte payloads do not allow the most efficient over-the-air
packet choice, and cannot achieve maximum throughput over BR/EDR.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

9 years agoBluetooth: Fix incorrect setting of remote_tx_win for L2CAP ERTM
Mat Martineau [Thu, 5 Aug 2010 22:54:23 +0000]
Bluetooth: Fix incorrect setting of remote_tx_win for L2CAP ERTM

remote_tx_win is intended to be set on receipt of an L2CAP
configuration request.  The value is used to determine the size of the
transmit window on the remote side of an ERTM connection, so L2CAP
can stop sending frames when that remote window is full.

An incorrect remote_tx_win value will cause the stack to not fully
utilize the tx window (performance impact), or to overfill the remote
tx window (causing dropped frames or a disconnect).

This patch removes an extra setting of remote_tx_win when a
configuration response is received.  The transmit window has a
different meaning in a response - it is an informational value
less than or equal to the local tx_win.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

9 years agoBluetooth: Change default L2CAP ERTM retransmit timeout
Mat Martineau [Thu, 5 Aug 2010 22:54:20 +0000]
Bluetooth: Change default L2CAP ERTM retransmit timeout

The L2CAP specification requires that the ERTM retransmit timeout be at
least 2 seconds for BR/EDR connections.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

9 years agoBluetooth: Fix endianness issue with L2CAP MPS configuration
Mat Martineau [Thu, 5 Aug 2010 22:54:22 +0000]
Bluetooth: Fix endianness issue with L2CAP MPS configuration

Incoming configuration values must be converted to native CPU order
before use.  This fixes a bug where a little-endian MPS value is
compared to a native CPU value.  On big-endian processors, this
can cause ERTM and streaming mode segmentation to produce PDUs
that are larger than the remote stack is expecting, or that would
produce fragmented skbs that the current FCS code cannot handle.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

9 years agonet: Use NET_XMIT_SUCCESS where possible.
Ben Greear [Tue, 10 Aug 2010 08:45:40 +0000]
net: Use NET_XMIT_SUCCESS where possible.

This is based on work originally done by Patric McHardy.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoisdn: mISDN: call pci_disable_device() if pci_probe() failed
Kulikov Vasiliy [Mon, 9 Aug 2010 09:50:53 +0000]
isdn: mISDN: call pci_disable_device() if pci_probe() failed

Driver should call pci_disable_device() if it returns from pci_probe()
with error.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoisdn: avm: call pci_disable_device() if pci_probe() failed
Kulikov Vasiliy [Mon, 9 Aug 2010 09:50:47 +0000]
isdn: avm: call pci_disable_device() if pci_probe() failed

Driver should call pci_disable_device() if it returns from pci_probe()
with error.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoisdn: avm: call pci_disable_device() if pci_probe() failed
Kulikov Vasiliy [Mon, 9 Aug 2010 09:50:37 +0000]
isdn: avm: call pci_disable_device() if pci_probe() failed

Driver should call pci_disable_device() if it returns from pci_probe()
with error.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agousbnet: rx_submit() should return an error code.
David S. Miller [Tue, 10 Aug 2010 09:50:55 +0000]
usbnet: rx_submit() should return an error code.

This patch makes rx_submit() return an error code, and makes some call sites
that care check the return value. This is important because it lets us properly
handle cases where the device isn't ready to handle URB submissions (e.g., when
it is autosuspended under some drivers); previously, we would attempt and fail
to submit URBs and reschedule ourselves to try and fail again. This patch is
against Linus's 2.6 repo commit 45d7f32c7a43cbb9592886d38190e379e2eb2226.

Signed-Off-By: Elizabeth Jones <ellyjones@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agopkt_sched: Add some basic qdisc class ops verification. Was: [PATCH] sfq: add dummy...
Jarek Poplawski [Mon, 9 Aug 2010 12:18:48 +0000]
pkt_sched: Add some basic qdisc class ops verification. Was: [PATCH] sfq: add dummy bind/unbind handles

Verify in register_qdisc() some basic qdisc class handlers are present.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agopkt_sched: sch_sfq: Add dummy unbind_tcf and put handles. Was: [PATCH] sfq: add dummy...
Jarek Poplawski [Mon, 9 Aug 2010 12:18:17 +0000]
pkt_sched: sch_sfq: Add dummy unbind_tcf and put handles. Was: [PATCH] sfq: add dummy bind/unbind handles

Add dummy .unbind_tcf and .put qdisc class ops for easier verification.
(All other schedulers have it like this.)

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoqlcnic: using too much stack
Dan Carpenter [Mon, 9 Aug 2010 21:49:36 +0000]
qlcnic: using too much stack

qlcnic_pci_info structs are 128 bytes so an array of 8 uses 1024 bytes.
That's a lot if you run with 4K stacks.  I allocated them with kcalloc()
instead.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoqlcnic: clean up qlcnic_init_pci_info()
Dan Carpenter [Mon, 9 Aug 2010 21:47:56 +0000]
qlcnic: clean up qlcnic_init_pci_info()

In the original code we allocated memory conditionally and freed it in
the error handling unconditionally.  It turns out that this function is
only called during initialization and "adapter->npars" and
"adapter->eswitch" are always NULL at the start of the function.  I
removed those checks.

Also since I was cleaning things, I changed the error handling for
qlcnic_get_pci_info() and pulled everything in an indent level.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agophy.c: fix kernel-doc warnings
Randy Dunlap [Mon, 9 Aug 2010 13:41:59 +0000]
phy.c: fix kernel-doc warnings

Fix phy.c kernel-doc notation:

Warning(drivers/net/phy/phy.c:313): No description found for parameter 'ifr'
Warning(drivers/net/phy/phy.c:313): Excess function parameter 'mii_data' description in 'phy_mii_ioctl'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonet/sock.h: add missing kernel-doc notation
Randy Dunlap [Mon, 9 Aug 2010 13:41:07 +0000]
net/sock.h: add missing kernel-doc notation

Add missing kernel-doc notation to struct sock:

Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_pid'
Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_cred'
Warning(include/net/sock.h:324): No description found for parameter 'sk_classid'
Warning(include/net/sock.h:324): Excess struct/union/enum/typedef member 'sk_peercred' description in 'sock'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoetherdevice.h: fix kernel-doc typo
Randy Dunlap [Mon, 9 Aug 2010 13:40:03 +0000]
etherdevice.h: fix kernel-doc typo

Fix etherdevice.h parameter name typo in kernel-doc:

Warning(include/linux/etherdevice.h:138): No description found for parameter 'hwaddr'
Warning(include/linux/etherdevice.h:138): Excess function parameter 'addr' description in 'dev_hw_addr_random'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agofarsync: Fix compile warnings.
David S. Miller [Tue, 10 Aug 2010 07:06:58 +0000]
farsync: Fix compile warnings.

drivers/net/wan/farsync.c: In function 'fst_intr_rx':
drivers/net/wan/farsync.c:1312: warning: cast to pointer from integer of different size
drivers/net/wan/farsync.c: In function 'do_bottom_half_tx':
drivers/net/wan/farsync.c:1407: warning: cast to pointer from integer of different size

The "skb" and "mem" arguments being passed here are DMA addresses
being programmed into the hardware registers, so pass them as the type
that they actually are.  And use the correct printf formatting in
debug logging statements for these things to match the type change.

Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoiwlagn: fix rts cts protection
Johannes Berg [Mon, 9 Aug 2010 17:57:02 +0000]
iwlagn: fix rts cts protection

Currently the driver will try to protect all frames,
which leads to a lot of odd things like sending an
RTS with a zeroed RA before multicast frames, which
is clearly bogus.

In order to fix all of this, we need to take a step
back and see what we need to achieve:
 * we need RTS/CTS protection if requested by
   the AP for the BSS, mac80211 tells us this
 * in that case, CTS-to-self should only be
   enabled when mac80211 tells us
 * additionally, as a hardware workaround, on
   some devices we have to protect aggregated
   frames with RTS

To achieve the first two items, set up the RXON
accordingly and set the protection required flag
in the transmit command when mac80211 requests
protection for the frame.

To achieve the last item, set the rate-control
RTS-requested flag for all stations that we have
aggregation sessions with, and set the protection
required flag when sending aggregated frames (on
those devices where this is required).

Since otherwise bugs can occur, do not allow the
user to override the RTS-for-aggregation setting
from sysfs any more.

Finally, also clean up the way all these flags get
set in the driver and move everything into the
device-specific functions.

Cc: stable@kernel.org [2.6.35]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agocfg80211: fix locking in action frame TX
Johannes Berg [Mon, 9 Aug 2010 13:52:03 +0000]
cfg80211: fix locking in action frame TX

Accesses to "wdev->current_bss" must be
locked with the wdev lock, which action
frame transmission is missing.

Cc: stable@kernel.org [2.6.33+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agolibertas: fix build break by including linux/sched.h
John W. Linville [Mon, 9 Aug 2010 19:14:21 +0000]
libertas: fix build break by including linux/sched.h

CC [M] drivers/net/wireless/libertas/cfg.o
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_scan_worker’:
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: ‘TASK_NORMAL’ undeclared (first use in this function)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: (Each undeclared identifier is reported only once
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: for each function it appears in.)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_cfg_connect’:
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘signal_pending’
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘schedule_timeout’

Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agoRevert "p54pci: Add PCI ID for SMC2802W"
John W. Linville [Mon, 9 Aug 2010 16:04:56 +0000]
Revert "p54pci: Add PCI ID for SMC2802W"

This reverts commit 5f7aebd845a9d2ed42f36b7333579ec3534b4713.

Apparently, that PCI ID data was incorrectly taken from the subsystem
information.  The actual ID matches another already known ID.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agoigbvf.txt: Add igbvf Documentation
Jeff Kirsher [Sun, 8 Aug 2010 15:54:31 +0000]
igbvf.txt: Add igbvf Documentation

Adds documentation for the igbvf (igb virtual function driver).

  v2:
   - Removed trailing white space
   - Removed Ethtool version info

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoigb.txt: Add igb documentation
Jeff Kirsher [Sun, 8 Aug 2010 15:54:11 +0000]
igb.txt: Add igb documentation

Add documentation for the igb networking driver.

  v2:
   - Removed trailing white space
   - Removed Ethtool version info
   - Removed LRO kernel version info

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoe100/e1000*/igb*/ixgb*: Add missing read memory barrier
Jeff Kirsher [Sun, 8 Aug 2010 16:02:31 +0000]
e100/e1000*/igb*/ixgb*: Add missing read memory barrier

Based on patches from Sonny Rao and Milton Miller...

Combined the patches to fix up clean_tx_irq and clean_rx_irq.

The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.

In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.

The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.

This bug was found during stress testing and adding this barrier has
been shown to fix it.  The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().

This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.

Previously Submitted to e1000-devel only for ixgbe

http://marc.info/?l=e1000-devel&m=126593062701537&w=3

We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.

CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoixgbe: fix build error with FCOE_CONFIG without DCB_CONFIG
John Fastabend [Sun, 8 Aug 2010 15:46:15 +0000]
ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIG

Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause
a build error.  This resolves the build error by wrapping
the fcoe.up in CONFIG_IXGBE_DCB ifdefs.

Also frames were being priority VLAN tagged even without DCB
enabled.  This fixes this so that 8021Q priority tags are
only added with DCB actually enabled.

Reported-by: divya <dipraksh@linux.vnet.ibm.com>
Reported-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonetxen: protect tx timeout recovery by rtnl lock
Amit Kumar Salecha [Sun, 8 Aug 2010 06:05:23 +0000]
netxen: protect tx timeout recovery by rtnl lock

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoisdn: gigaset: use after free
Dan Carpenter [Thu, 5 Aug 2010 22:21:26 +0000]
isdn: gigaset: use after free

I moved the kfree(cb) below the dereferences.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoisdn: gigaset: add missing unlock
Dan Carpenter [Thu, 5 Aug 2010 22:23:23 +0000]
isdn: gigaset: add missing unlock

We should unlock here.  This is the only place where we return from the
function with the lock held.  The caller isn't expecting it.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agosolos-pci: Fix race condition in tasklet RX handling
David Woodhouse [Sun, 8 Aug 2010 06:02:59 +0000]
solos-pci: Fix race condition in tasklet RX handling

We were seeing faults in the solos-pci receive tasklet when packets
arrived for a VCC which was currently being closed:

[18842.727906] EIP: [<e082f490>] br2684_push+0x19/0x234 [br2684] SS:ESP 0068:dfb89d14

[18845.090712] [<c13ecff3>] ? do_page_fault+0x0/0x2e1
[18845.120042] [<e082f490>] ? br2684_push+0x19/0x234 [br2684]
[18845.153530] [<e084fa13>] solos_bh+0x28b/0x7c8 [solos_pci]
[18845.186488] [<e084f711>] ? solos_irq+0x2d/0x51 [solos_pci]
[18845.219960] [<c100387b>] ? handle_irq+0x3b/0x48
[18845.247732] [<c10265cb>] ? irq_exit+0x34/0x57
[18845.274437] [<c1025720>] tasklet_action+0x42/0x69
[18845.303247] [<c102643f>] __do_softirq+0x8e/0x129
[18845.331540] [<c10264ff>] do_softirq+0x25/0x2a
[18845.358274] [<c102664c>] _local_bh_enable_ip+0x5e/0x6a
[18845.389677] [<c102666d>] local_bh_enable+0xb/0xe
[18845.417944] [<e08490a8>] ppp_unregister_channel+0x32/0xbb [ppp_generic]
[18845.458193] [<e08731ad>] pppox_unbind_sock+0x18/0x1f [pppox]

This patch uses an RCU-inspired approach to fix it. In the RX tasklet's
find_vcc() function we first refuse to use a VCC which already has the
ATM_VF_READY bit cleared. And in the VCC close function, we synchronise
with the tasklet to ensure that it can't still be using the VCC before
we continue and allow the VCC to be destroyed.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Nathan Williams <nathan@traverse.com.au>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agopkt_sched: Fix sch_sfq vs tcf_bind_filter oops
Jarek Poplawski [Fri, 6 Aug 2010 00:22:35 +0000]
pkt_sched: Fix sch_sfq vs tcf_bind_filter oops

Since there was added ->tcf_chain() method without ->bind_tcf() to
sch_sfq class options, there is oops when a filter is added with
the classid parameter.

Fixes commit 7d2681a6ff4f9ab5e48d02550b4c6338f1638998
netdev thread: null pointer at cls_api.c

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Reported-by: Franchoze Eric <franchoze@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonet: disable preemption before call smp_processor_id()
Changli Gao [Sun, 8 Aug 2010 03:35:43 +0000]
net: disable preemption before call smp_processor_id()

Although netif_rx() isn't expected to be called in process context with
preemption enabled, it'd better handle this case. And this is why get_cpu()
is used in the non-RPS #ifdef branch. If tree RCU is selected,
rcu_read_lock() won't disable preemption, so preempt_disable() should be
called explictly.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agotcp: no md5sig option size check bug
Dmitry Popov [Sun, 8 Aug 2010 03:24:28 +0000]
tcp: no md5sig option size check bug

tcp_parse_md5sig_option doesn't check md5sig option (TCPOPT_MD5SIG)
length, but tcp_v[46]_inbound_md5_hash assume that it's at least 16
bytes long.

Signed-off-by: Dmitry Popov <dp@highloadlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Fri, 6 Aug 2010 20:30:43 +0000]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

9 years agoiwlwifi: fix locking assertions
Johannes Berg [Fri, 6 Aug 2010 14:17:53 +0000]
iwlwifi: fix locking assertions

spin_is_locked() can return zero on some (UP?)
configurations because locks don't exist, and
that causes an endless amount of warnings. Use
lockdep_assert_held() instead, which has two
advantages:
 1) it verifies the current task is holding
    the lock or mutex
 2) it compiles away completely when lockdep
    is not enabled

Cc: stable@kernel.org [2.6.34+, maybe only parts of patch]
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agoiwlwifi: fix TX tracer
Johannes Berg [Fri, 6 Aug 2010 14:00:48 +0000]
iwlwifi: fix TX tracer

The TX tracing code copies with the wrong length,
which will typically copy too little data. Fix
this by using the correct length variable.

Cc: stable@kernel.org [2.6.32+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agoisdn: fix information leak
Dan Carpenter [Wed, 4 Aug 2010 23:38:06 +0000]
isdn: fix information leak

The main motivation of this patch changing strcpy() to strlcpy().
We strcpy() to copy a 48 byte buffers into a 49 byte buffers.  So at
best the last byte has leaked information, or maybe there is an
overflow?  Anyway, this patch closes the information leaks by zeroing
the memory and the calls to strlcpy() prevent overflows.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agonet: Fix napi_gro_frags vs netpoll path
Jarek Poplawski [Thu, 5 Aug 2010 01:19:11 +0000]
net: Fix napi_gro_frags vs netpoll path

The netpoll_rx_on() check in __napi_gro_receive() skips part of the
"common" GRO_NORMAL path, especially "pull:" in dev_gro_receive(),
where at least eth header should be copied for entirely paged skbs.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agousbnet: remove noisy and hardly useful printk
Christian Samsel [Wed, 4 Aug 2010 22:14:36 +0000]
usbnet: remove noisy and hardly useful printk

With turned on hspa modem (Dell 5530 internal card) and activated usb auto
suspend, my system gets up 100 "usbnet_resume has delayed data" per
minute. I didnt noticed any pathological behaviour, so just drop
this message. if any objections, please at least change it to _DEBUG.

Signed-off-by: Christian Samsel <christian.samsel@rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agortl8180: avoid potential NULL deref in rtl8180_beacon_work
John W. Linville [Thu, 5 Aug 2010 17:46:27 +0000]
rtl8180: avoid potential NULL deref in rtl8180_beacon_work

ieee80211_beacon_get can return NULL...

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org

9 years agoath9k: Remove myself from the MAINTAINERS list
Sujith [Fri, 30 Jul 2010 06:31:17 +0000]
ath9k: Remove myself from the MAINTAINERS list

So long.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

9 years agolibertas: scan before assocation if no BSSID was given
Dan Williams [Wed, 4 Aug 2010 05:43:47 +0000]
libertas: scan before assocation if no BSSID was given

Fix this leftover TODO from the cfg80211 conversion by doing a scan
if cfg80211 didn't pass in the BSSID for us.  Since the scan code
uses so much of the cfg80211_scan_request structure to build up the
firmware command, we just fake one when the scan request is triggered
internally.  But we need to make sure that internal 'fake' cfg82011
scan request does not get back to cfg82011 via cfg80211_scan_done().

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>