9 years agoPCI: MSI: Restore read_msi_msg_desc(); add get_cached_msi_msg_desc()
Ben Hutchings [Fri, 23 Jul 2010 13:56:28 +0000]
PCI: MSI: Restore read_msi_msg_desc(); add get_cached_msi_msg_desc()

commit 2ca1af9aa3285c6a5f103ed31ad09f7399fc65d7 "PCI: MSI: Remove
unsafe and unnecessary hardware access" changed read_msi_msg_desc() to
return the last MSI message written instead of reading it from the
device, since it may be called while the device is in a reduced
power state.

However, the pSeries platform code really does need to read messages
from the device, since they are initially written by firmware.
Therefore:
- Restore the previous behaviour of read_msi_msg_desc()
- Add new functions get_cached_msi_msg{,_desc}() which return the
  last MSI message written
- Use the new functions where appropriate

Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: export SMBIOS provided firmware instance and label to sysfs
Narendra K [Mon, 26 Jul 2010 10:56:50 +0000]
PCI: export SMBIOS provided firmware instance and label to sysfs

This patch exports SMBIOS provided firmware instance and label of
onboard PCI devices to sysfs.  New files are:
  /sys/bus/pci/devices/.../label which contains the firmware name for
the device in question, and
  /sys/bus/pci/devices/.../index which contains the firmware device type
instance for the given device.

Signed-off-by: Jordan Hargrave <jordan_hargrave@dell.com>
Signed-off-by: Narendra K <narendra_k@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: Allow read/write access to sysfs I/O port resources
Alex Williamson [Mon, 19 Jul 2010 15:45:34 +0000]
PCI: Allow read/write access to sysfs I/O port resources

PCI sysfs resource files currently only allow mmap'ing.  On x86 this
works fine for memory backed BARs, but doesn't work at all for I/O
port backed BARs.  Add read/write to I/O port PCI sysfs resource
files to allow userspace access to these device regions.

Acked-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agox86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN
Bjorn Helgaas [Fri, 23 Jul 2010 18:53:27 +0000]
x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN

This DMI quirk turns on "pci=use_crs" for the ALiveSATA2-GLAN because
amd_bus.c doesn't handle this system correctly.

The system has a single HyperTransport I/O chain, but has two PCI host
bridges to buses 00 and 80.  amd_bus.c learns the MMIO range associated
with buses 00-ff and that this range is routed to the HT chain hosted at
node 0, link 0:

    bus: [00, ff] on node 0 link 0
    bus: 00 index 1 [mem 0x80000000-0xfcffffffff]

This includes the address space for both bus 00 and bus 80, and amd_bus.c
assumes it's all routed to bus 00.

We find device 80:01.0, which BIOS left in the middle of that space, but
we don't find a bridge from bus 00 to bus 80, so we conclude that 80:01.0
is unreachable from bus 00, and we move it from the original, working,
address to something outside the bus 00 aperture, which does not work:

    pci 0000:80:01.0: reg 10: [mem 0xfebfc000-0xfebfffff 64bit]
    pci 0000:80:01.0: BAR 0: assigned [mem 0xfd00000000-0xfd00003fff 64bit]

The BIOS told us everything we need to know to handle this correctly,
so we're better off if we just pay attention, which lets us leave the
80:01.0 device at the original, working, address:

    ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7f])
    pci_root PNP0A03:00: host bridge window [mem 0x80000000-0xff37ffff]
    ACPI: PCI Root Bridge [PCI1] (domain 0000 [bus 80-ff])
    pci_root PNP0A08:00: host bridge window [mem 0xfebfc000-0xfebfffff]

This was a regression between 2.6.33 and 2.6.34.  In 2.6.33, amd_bus.c
was used only when we found multiple HT chains.  3e3da00c01d050, which
enabled amd_bus.c even on systems with a single HT chain, caused this
failure.

This quirk was written by Graham.  If we ever enable "pci=use_crs" for
machines from 2006 or earlir, this quirk should be removed.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16007

Cc: stable@kernel.org
Reported-by: Graham Ramsey <ramsey.graham@ntlworld.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: remove unused HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_{SIZE|BOUNDARY}
FUJITA Tomonori [Mon, 12 Jul 2010 06:59:11 +0000]
PCI: remove unused HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_{SIZE|BOUNDARY}

In 2.6.34, we transformed the PCI DMA API into the generic device
mode. The PCI DMA API is just the wrapper of the DMA API.

So we don't need HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_SIZE or
HAVE_ARCH_PCI_SET_DMA_SEGMENT_BOUNDARY (which enable architectures to
have the own implementations). Both haven't been used anyway.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: disable mmio during bar sizing
Jacob Pan [Fri, 16 Jul 2010 17:19:22 +0000]
PCI: disable mmio during bar sizing

It is a known issue that mmio decoding shall be disabled while doing PCI
bar sizing. Host bridge and other devices (PCI PIC) shall be excluded for
certain platforms. This patch mainly comes from Mathew Willcox's
patch in http://kerneltrap.org/mailarchive/linux-kernel/2007/9/13/258969.

A new flag bit "mmio_alway_on" is added to pci_dev with the intention that
devices with their mmio decoding cannot be disabled during BAR sizing shall
have this bit set, preferrablly in their quirks.

Without this patch, Intel Moorestown platform graphics unit will be
corrupted during bar sizing activities.

Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: MSI: Remove unsafe and unnecessary hardware access
Ben Hutchings [Thu, 17 Jun 2010 19:16:36 +0000]
PCI: MSI: Remove unsafe and unnecessary hardware access

During suspend on an SMP system, {read,write}_msi_msg_desc() may be
called to mask and unmask interrupts on a device that is already in a
reduced power state.  At this point memory-mapped registers including
MSI-X tables are not accessible, and config space may not be fully
functional either.

While a device is in a reduced power state its interrupts are
effectively masked and its MSI(-X) state will be restored when it is
brought back to D0.  Therefore these functions can simply read and
write msi_desc::msg for devices not in D0.

Further, read_msi_msg_desc() should only ever be used to update a
previously written message, so it can always read msi_desc::msg
and never needs to touch the hardware.

Tested-by: "Michael Chan" <mchan@broadcom.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: Default PCIe ASPM control to on and require !EMBEDDED to disable
Matthew Garrett [Tue, 22 Jun 2010 21:03:03 +0000]
PCI: Default PCIe ASPM control to on and require !EMBEDDED to disable

The CONFIG_PCIEASPM option is confusing and potentially dangerous. ASPM is
a hardware mediated feature rather than one under direct OS control, and
even if the config option is disabled the system firmware may have turned
on ASPM on various bits of hardware. This can cause problems later -
various hardware that claims to support ASPM does a poor job of it and may
hang or cause other difficulties. The kernel is able to recognise this in
many cases and disable the ASPM functionality, but only if CONFIG_PCIEASPM
is enabled.

Given that in its default configuration this option will either leave the
hardware as it was originally or disable hardware functionality that may
cause problems, it should by default y. The only reason to disable it
ought to be to reduce code size, so make it dependent on CONFIG_EMBEDDED.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: lrodriguez@atheros.com
Cc: maximlevitsky@gmail.com
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: kernel oops on access to pci proc file while hot-removal
Kenji Kaneshige [Wed, 23 Jun 2010 07:04:10 +0000]
PCI: kernel oops on access to pci proc file while hot-removal

I encountered the problem that /proc/bus/pci/XX/YY is not removed even
after the corresponding device is hot-removed, if the file is still
being opened. In addtion, accessing this file in this situation causes
kernel panic (see below).

Becasue the pci_proc_detach_device() doesn't call remove_proc_entry()
if struct proc_dir_entry->count > 1, access to /proc/bus/pci/XX/YY
would refer to struct pci_dev that was already freed.

Though I don't know why the check for proc_dir_entry->count was added,
I don't think it is needed. Removing this check fixes the problem.

Steps to reproduce
------------------
# cd /sys/bus/pci/slots/2/
# PROC_BUS_PCI_FILE=/proc/bus/pci/`awk -F: '{print $2"/"$3}' < address`.0
# sleep 10000 < $PROC_BUS_PCI_FILE &
# echo 0 > power
# while true; do cat $PROC_BUS_PCI_FILE > /dev/null; done

Oops Messages
-------------
BUG: unable to handle kernel NULL pointer dereference at 00000042
IP: [<c05c82d5>] pci_user_read_config_dword+0x65/0xa0
*pdpt = 000000002185e001 *pde = 0000000476a79067
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1c.0/0000:10:00.0/local_cpus
Modules linked in: autofs4 sunrpc cpufreq_ondemand acpi_cpufreq ipv6 dm_mirror dm_region_hash dm_log dm_mod e1000e i2c_i801 i2c_core iTCO_wdt igb sg pcspkr dca iTCO_vendor_support ext4 mbcache jbd2 sd_mod crc_t10dif lpfc mptsas scsi_transport_fc mptscsih mptbase scsi_tgt scsi_transport_sas [last unloaded: microcode]

Pid: 2997, comm: cat Not tainted 2.6.34-kk #32 SB/PRIMEQUEST 1800E
EIP: 0060:[<c05c82d5>] EFLAGS: 00010046 CPU: 19
EIP is at pci_user_read_config_dword+0x65/0xa0
EAX: 00000002 EBX: e44f1800 ECX: e144df14 EDX: 155668c7
ESI: 00000087 EDI: 00000000 EBP: e144df40 ESP: e144df0c
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process cat (pid: 2997, ti=e144c000 task=e26f2570 task.ti=e144c000)
Stack:
 c09ceac0 c0570f72 ffffffff 08c57000 00000000 00001000 e44f1800 c05d2404
<0> e144df40 00001000 00000000 00001000 08c57000 3093ae50 e420cb40 e358d5c0
<0> c05d2300 fffffffb c054984f e144df9c 00008000 08c57000 e358d5c0 00008000
Call Trace:
 [<c0570f72>] ? security_capable+0x22/0x30
 [<c05d2404>] ? proc_bus_pci_read+0x104/0x220
 [<c05d2300>] ? proc_bus_pci_read+0x0/0x220
 [<c054984f>] ? proc_reg_read+0x5f/0x90
 [<c05497f0>] ? proc_reg_read+0x0/0x90
 [<c050694d>] ? vfs_read+0x9d/0x190
 [<c04958f4>] ? audit_syscall_entry+0x204/0x230
 [<c0506a81>] ? sys_read+0x41/0x70
 [<c0402f1f>] ? sysenter_do_call+0x12/0x28
Code: b4 26 00 00 00 00 b8 20 88 b1 c0 c7 44 24 08 ff ff ff ff e8 3e 52 22 00 f6 83 24 04 00 00 20 75 34 8b 43 08 8d 4c 24 08 8b 53 1c <8b> 70 40 89 4c 24 04 89 f9 c7 04 24 04 00 00 00 ff 16 89 c6 f0
EIP: [<c05c82d5>] pci_user_read_config_dword+0x65/0xa0 SS:ESP 0068:e144df0c
CR2: 0000000000000042

Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: pci-sysfs: remove casts from void*
Kulikov Vasiliy [Tue, 29 Jun 2010 10:15:28 +0000]
PCI: pci-sysfs: remove casts from void*

Remove unnesessary casts from void*.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoACPI: Disable ASPM if the platform won't provide _OSC control for PCIe
Matthew Garrett [Tue, 22 Jun 2010 15:25:43 +0000]
ACPI: Disable ASPM if the platform won't provide _OSC control for PCIe

The PCI SIG documentation for the _OSC OS/firmware handshaking interface
states:

"If the _OSC control method is absent from the scope of a host bridge
device, then the operating system must not enable or attempt to use any
features defined in this section for the hierarchy originated by the host
bridge."

The obvious interpretation of this is that the OS should not attempt to use
PCIe hotplug, PME or AER - however, the specification also notes that an
_OSC method is *required* for PCIe hierarchies, and experimental validation
with An Alternative OS indicates that it doesn't use any PCIe functionality
if the _OSC method is missing. That arguably means we shouldn't be using
MSI or extended config space, but right now our problems seem to be limited
to vendors being surprised when ASPM gets enabled on machines when other
OSs refuse to do so. So, for now, let's just disable ASPM if the _OSC
method doesn't exist or refuses to hand over PCIe capability control.

Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI hotplug: make sure child bridges are enabled at hotplug time
Yinghai Lu [Fri, 21 May 2010 21:35:06 +0000]
PCI hotplug: make sure child bridges are enabled at hotplug time

Found one PCIe Module with several bridges built-in where a "cold"
hotadd doesn't work.

If we end up reassigning bridge windows at hotadd time, and have to loop
through assigning new ranges, we won't end up enabling the child bridges
because the first assignment pass already tried to enable them, which
prevents __pci_bridge_assign_resource from updating the windows.

So try to move enabling of child bridges to the end, and only do it
once.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI hotplug: shpchp: Removed check for hotplug of display devices
Praveen Kalamegham [Thu, 20 May 2010 17:15:01 +0000]
PCI hotplug: shpchp: Removed check for hotplug of display devices

Removed check to prevent hotplug of display devices within shpchp.
Originally this was thought to have been required within the PCI
Hotplug specification for some legacy devices.  However there is
no such requirement in the most recent revision. The check prevents
hotplug of not only display devices but also computational GPUs
which require serviceability.

Signed-off-by: Praveen Kalamegham <praveen@nextio.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI hotplug: pciehp: Fixed return value sign for pciehp_unconfigure_device
Praveen Kalamegham [Thu, 20 May 2010 20:32:22 +0000]
PCI hotplug: pciehp: Fixed return value sign for pciehp_unconfigure_device

pciehp_unconfigure_device() should return -EINVAL, not EINVAL.

Signed-off-by: Praveen Kalamegham <praveen@nextio.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: Don't enable aspm before drivers have had a chance to veto it
Matthew Garrett [Wed, 9 Jun 2010 20:05:07 +0000]
PCI: Don't enable aspm before drivers have had a chance to veto it

The aspm code will currently set the configured aspm policy before drivers
have had an opportunity to indicate that their hardware doesn't support it.
Unfortunately, putting some hardware in L0 or L1 can result in the hardware
no longer responding to any requests, even after aspm is disabled. It makes
more sense to leave aspm policy at the BIOS defaults at initial setup time,
reconfiguring it after pci_enable_device() is called. This allows the
driver to blacklist individual devices beforehand.

Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: fix wrong memory address handling in MSI-X
Kenji Kaneshige [Thu, 17 Jun 2010 01:42:44 +0000]
PCI: fix wrong memory address handling in MSI-X

Use resource_size_t for MMIO address instead of unsigned long. Otherwise,
higher 32-bits of MMIO address are cleared unexpectedly in x86-32 PAE.

Acked-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: check return value of pci_enable_device() when enabling bridges
Junchang Wang [Fri, 18 Jun 2010 02:02:33 +0000]
PCI: check return value of pci_enable_device() when enabling bridges

pci_enable_device can fail. In that case, a printed warning would be
more appropriate.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: sparse warning (trivial)
Stephen Hemminger [Tue, 1 Jun 2010 16:00:16 +0000]
PCI: sparse warning (trivial)

Assigning zero where NULL should be used.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agox86/PCI: Add option to not assign BAR's if not already assigned
Mike Habeck [Wed, 12 May 2010 18:14:32 +0000]
x86/PCI: Add option to not assign BAR's if not already assigned

The Linux kernel assigns BARs that a BIOS did not assign, most likely
to handle broken BIOSes that didn't enumerate the devices correctly.
On UV the BIOS purposely doesn't assign I/O BARs for certain devices/
drivers we know don't use them (examples, LSI SAS, Qlogic FC, ...).
We purposely don't assign these I/O BARs because I/O Space is a very
limited resource.  There is only 64k of I/O Space, and in a PCIe
topology that space gets divided up into 4k chucks (this is due to
the fact that a pci-to-pci bridge's I/O decoder is aligned at 4k)...
Thus a system can have at most 16 cards with I/O BARs: (64k / 4k = 16)

SGI needs to scale to >16 devices with I/O BARs.  So by not assigning
I/O BARs on devices we know don't use them, we can do that (iff the
kernel doesn't go and assign these BARs that the BIOS purposely didn't
assign).

This patch will not assign a resource to a device BAR if that BAR was
not assigned by the BIOS, and the kernel cmdline option 'pci=nobar'
was specified.   This patch is closely modeled after the 'pci=norom'
option that currently exists in the tree.

Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: disable MSI on VIA K8M800
Tejun Heo [Sun, 23 May 2010 08:22:55 +0000]
PCI: disable MSI on VIA K8M800

MSI delivery from on-board ahci controller doesn't work on K8M800.  At
this point, it's unclear whether the culprit is with the ahci
controller or the host bridge.  Given the track record and considering
the rather minimal impact of MSI, disabling it seems reasonable.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Rainer Hurtado Navarro <publio.escipion.el.africano@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI quirk: AMD 780: work around wrong vendor ID on APC bridge
Clemens Ladisch [Wed, 26 May 2010 10:21:10 +0000]
PCI quirk: AMD 780: work around wrong vendor ID on APC bridge

In all AMD 780 family northbridges, the vendor ID of the internal
graphics PCI/PCI bridge reads not as AMD but as that of the mainboard
vendor, because the hardware actually returns the value of the subsystem
vendor ID (erratum 18).

We currently have additional quirk entries for Asus and Acer, but it is
likely that we will encounter more systems with other vendor IDs.

Since we do not know in advance all possible vendor IDs, a better way to
find the device is to declare the quirk on the host bridge, whose ID is
always correct, and use that device as a stepping stone to find the PCI/
PCI bridge, if present.

Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: hotplug/shpchp_hpc: add parenthesis in SLOT_REG_RSVDZ_MASK
Dan Carpenter [Wed, 26 May 2010 10:46:39 +0000]
PCI: hotplug/shpchp_hpc: add parenthesis in SLOT_REG_RSVDZ_MASK

The SLOT_REG_RSVDZ_MASK macro is normally used like this:
slot_reg &= ~SLOT_REG_RSVDZ_MASK;
The ~ operator has higher precedence than the | operator from inside the
macro, so it needs parenthesis.

Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI aerdrv: fix annoying warnings
Linus Torvalds [Thu, 27 May 2010 02:21:11 +0000]
PCI aerdrv: fix annoying warnings

Some compiler generates following warnings:

  In function 'aer_isr':
  warning: 'e_src.id' may be used uninitialized in this function
  warning: 'e_src.status' may be used uninitialized in this function

Avoid status flag "int ret" and return constants instead, so that
gcc sees the return value matching "it is initialized" better.

Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agox86/PCI: pci, fix section mismatch
Jiri Slaby [Tue, 15 Jun 2010 13:43:19 +0000]
x86/PCI: pci, fix section mismatch

pcibios_scan_specific_bus calls pci_scan_bus_on_node which is
__devinit. Mark pcibios_scan_specific_bus __devinit as well since
all users are now __init or __devinit.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoPCI: change device runtime PM settings for probe and remove
Alan Stern [Tue, 8 Jun 2010 19:23:51 +0000]
PCI: change device runtime PM settings for probe and remove

This patch (as1388) changes the way the PCI core handles runtime PM
settings when probing or unbinding drivers.  Now the core will make
sure the device is enabled for runtime PM, with a usage count >= 1,
when a driver is probed.  It does the same when calling a driver's
remove method.

If the driver wants to use runtime PM, all it has to do is call
pm_runtime_pu_noidle() near the end of its probe routine (to cancel
the core's usage increment) and pm_runtime_get_noresume() near the
start of its remove routine (to restore the usage count).  It does not
need to mess around with setting the runtime state to enabled,
disabled, active, or suspended.

The patch updates e1000e and r8169, the only PCI drivers that already
use the existing runtime PM interface.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

9 years agoMerge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
Linus Torvalds [Thu, 29 Jul 2010 22:23:28 +0000]
Merge branch 'for-linus' of git://git390.marist.edu/linux-2.6

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] etr: fix clock synchronization race
  [S390] Fix IRQ tracing in case of PER

9 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog
Linus Torvalds [Thu, 29 Jul 2010 22:21:44 +0000]
Merge git://git./linux/kernel/git/wim/linux-2.6-watchdog

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  watchdog: update MAINTAINERS entry

9 years agoMerge branch 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
Linus Torvalds [Thu, 29 Jul 2010 22:21:07 +0000]
Merge branch 'fix/hda' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Add a PC-beep workaround for ASUS P5-V
  ALSA: hda - Assume PC-beep as default for Realtek
  ALSA: hda - Don't register beep input device when no beep is available
  ALSA: hda - Fix pin-detection of Nvidia HDMI

9 years agoCRED: Fix __task_cred()'s lockdep check and banner comment
David Howells [Thu, 29 Jul 2010 11:45:55 +0000]
CRED: Fix __task_cred()'s lockdep check and banner comment

Fix __task_cred()'s lockdep check by removing the following validation
condition:

lockdep_tasklist_lock_is_held()

as commit_creds() does not take the tasklist_lock, and nor do most of the
functions that call it, so this check is pointless and it can prevent
detection of the RCU lock not being held if the tasklist_lock is held.

Instead, add the following validation condition:

task->exit_state >= 0

to permit the access if the target task is dead and therefore unable to change
its own credentials.

Fix __task_cred()'s comment to:

 (1) discard the bit that says that the caller must prevent the target task
     from being deleted.  That shouldn't need saying.

 (2) Add a comment indicating the result of __task_cred() should not be passed
     directly to get_cred(), but rather than get_task_cred() should be used
     instead.

Also put a note into the documentation to enforce this point there too.

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

9 years agoCRED: Fix get_task_cred() and task_state() to not resurrect dead credentials
David Howells [Thu, 29 Jul 2010 11:45:49 +0000]
CRED: Fix get_task_cred() and task_state() to not resurrect dead credentials

It's possible for get_task_cred() as it currently stands to 'corrupt' a set of
credentials by incrementing their usage count after their replacement by the
task being accessed.

What happens is that get_task_cred() can race with commit_creds():

TASK_1 TASK_2 RCU_CLEANER
-->get_task_cred(TASK_2)
rcu_read_lock()
__cred = __task_cred(TASK_2)
-->commit_creds()
old_cred = TASK_2->real_cred
TASK_2->real_cred = ...
put_cred(old_cred)
  call_rcu(old_cred)
[__cred->usage == 0]
get_cred(__cred)
[__cred->usage == 1]
rcu_read_unlock()
-->put_cred_rcu()
[__cred->usage == 1]
panic()

However, since a tasks credentials are generally not changed very often, we can
reasonably make use of a loop involving reading the creds pointer and using
atomic_inc_not_zero() to attempt to increment it if it hasn't already hit zero.

If successful, we can safely return the credentials in the knowledge that, even
if the task we're accessing has released them, they haven't gone to the RCU
cleanup code.

We then change task_state() in procfs to use get_task_cred() rather than
calling get_cred() on the result of __task_cred(), as that suffers from the
same problem.

Without this change, a BUG_ON in __put_cred() or in put_cred_rcu() can be
tripped when it is noticed that the usage count is not zero as it ought to be,
for example:

kernel BUG at kernel/cred.c:168!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/kernel/mm/ksm/run
CPU 0
Pid: 2436, comm: master Not tainted 2.6.33.3-85.fc13.x86_64 #1 0HR330/OptiPlex
745
RIP: 0010:[<ffffffff81069881>]  [<ffffffff81069881>] __put_cred+0xc/0x45
RSP: 0018:ffff88019e7e9eb8  EFLAGS: 00010202
RAX: 0000000000000001 RBX: ffff880161514480 RCX: 00000000ffffffff
RDX: 00000000ffffffff RSI: ffff880140c690c0 RDI: ffff880140c690c0
RBP: ffff88019e7e9eb8 R08: 00000000000000d0 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000040 R12: ffff880140c690c0
R13: ffff88019e77aea0 R14: 00007fff336b0a5c R15: 0000000000000001
FS:  00007f12f50d97c0(0000) GS:ffff880007400000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8f461bc000 CR3: 00000001b26ce000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process master (pid: 2436, threadinfo ffff88019e7e8000, task ffff88019e77aea0)
Stack:
 ffff88019e7e9ec8 ffffffff810698cd ffff88019e7e9ef8 ffffffff81069b45
<0> ffff880161514180 ffff880161514480 ffff880161514180 0000000000000000
<0> ffff88019e7e9f28 ffffffff8106aace 0000000000000001 0000000000000246
Call Trace:
 [<ffffffff810698cd>] put_cred+0x13/0x15
 [<ffffffff81069b45>] commit_creds+0x16b/0x175
 [<ffffffff8106aace>] set_current_groups+0x47/0x4e
 [<ffffffff8106ac89>] sys_setgroups+0xf6/0x105
 [<ffffffff81009b02>] system_call_fastpath+0x16/0x1b
Code: 48 8d 71 ff e8 7e 4e 15 00 85 c0 78 0b 8b 75 ec 48 89 df e8 ef 4a 15 00
48 83 c4 18 5b c9 c3 55 8b 07 8b 07 48 89 e5 85 c0 74 04 <0f> 0b eb fe 65 48 8b
04 25 00 cc 00 00 48 3b b8 58 04 00 00 75
RIP  [<ffffffff81069881>] __put_cred+0xc/0x45
 RSP <ffff88019e7e9eb8>
---[ end trace df391256a100ebdd ]---

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

9 years agowatchdog: update MAINTAINERS entry
Wim Van Sebroeck [Thu, 29 Jul 2010 18:02:51 +0000]
watchdog: update MAINTAINERS entry

Add Mailing-list and website to watchdog MAINTAINERS entry.

Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

9 years agoALSA: hda - Add a PC-beep workaround for ASUS P5-V
Takashi Iwai [Thu, 29 Jul 2010 13:30:02 +0000]
ALSA: hda - Add a PC-beep workaround for ASUS P5-V

ASUS P5-V provides a SSID that unexpectedly matches with the value
compilant with Realtek's specification.  Thus the driver interprets
it badly, resulting in non-working PC beep.

This patch adds a white-list for such a case; a white-list of known
devices with working PC beep.

Signed-off-by: Takashi Iwai <tiwai@suse.de>

9 years agoMerge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel...
Linus Torvalds [Thu, 29 Jul 2010 03:01:26 +0000]
Merge branch 'for_linus' of git://git./linux/kernel/git/jwessel/linux-2.6-kgdb

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
  x86,kgdb: Fix hw breakpoint regression

9 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
Linus Torvalds [Thu, 29 Jul 2010 03:00:42 +0000]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] ibmvscsi: Fix oops when an interrupt is pending during probe
  [SCSI] zfcp: Update status read mempool
  [SCSI] zfcp: Do not wait for SBALs on stopped queue
  [SCSI] zfcp: Fix check whether unchained ct_els is possible
  [SCSI] ipr: fix resource path display and formatting

9 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
Linus Torvalds [Thu, 29 Jul 2010 02:59:55 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/lrg/voltage-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
  regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
  wm8350-regulator: fix wm8350_register_regulator error handling
  ab3100: fix off-by-one value range checking for voltage selector

9 years agoecryptfs: Bugfix for error related to ecryptfs_hash_buckets
Andre Osterhues [Tue, 13 Jul 2010 20:59:17 +0000]
ecryptfs: Bugfix for error related to ecryptfs_hash_buckets

The function ecryptfs_uid_hash wrongly assumes that the
second parameter to hash_long() is the number of hash
buckets instead of the number of hash bits.
This patch fixes that and renames the variable
ecryptfs_hash_buckets to ecryptfs_hash_bits to make it
clearer.

Fixes: CVE-2010-2492

Signed-off-by: Andre Osterhues <aosterhues@escrypt.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

9 years agox86,kgdb: Fix hw breakpoint regression
Jason Wessel [Thu, 29 Jul 2010 00:10:30 +0000]
x86,kgdb: Fix hw breakpoint regression

HW breakpoints events stopped working correctly with kgdb
as a result of commit: 018cbffe6819f6f8db20a0a3acd9bab9bfd667e4
(Merge commit 'v2.6.33' into perf/core).

The regression occurred because the behavior changed for setting
NOTIFY_STOP as the return value to the die notifier if the breakpoint
was known to the HW breakpoint API.  Because kgdb is using the HW
breakpoint API to register HW breakpoints slots, it must also now
implement the overflow_handler call back else kgdb does not get to see
the events from the die notifier.

The kgdb_ll_trap function will be changed to be general purpose code
which can allow an easy way to implement the hw_breakpoint API
overflow call back.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>

9 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph...
Linus Torvalds [Wed, 28 Jul 2010 18:10:53 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: use complete_all and wake_up_all
  ceph: Correct obvious typo of Kconfig variable "CRYPTO_AES"
  ceph: fix dentry lease release
  ceph: fix leak of dentry in ceph_init_dentry() error path
  ceph: fix pg_mapping leak on pg_temp updates
  ceph: fix d_release dop for snapdir, snapped dentries
  ceph: avoid dcache readdir for snapdir

9 years agoGFS2: Use kmalloc when possible for ->readdir()
Steven Whitehouse [Wed, 28 Jul 2010 16:56:23 +0000]
GFS2: Use kmalloc when possible for ->readdir()

If we don't need a huge amount of memory in ->readdir() then
we can use kmalloc rather than vmalloc to allocate it. This
should cut down on the greater overheads associated with
vmalloc for smaller directories.

We may be able to eliminate vmalloc entirely at some stage,
but this is easy to do right away.

Also using GFP_NOFS to avoid any issues wrt to deleting inodes
while under a glock, and suggestion from Linus to factor out
the alloc/dealloc.

I've given this a test with a variety of different sized
directories and it seems to work ok.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

9 years agoALSA: hda - Assume PC-beep as default for Realtek
Takashi Iwai [Wed, 28 Jul 2010 15:43:36 +0000]
ALSA: hda - Assume PC-beep as default for Realtek

Enable PC-beep as default for hardwares that aren't compliant with the
SSID value Realtek requires.  In such a case, better to enable the beep
to avoid a regression.

Signed-off-by: Takashi Iwai <tiwai@suse.de>

9 years agoALSA: hda - Don't register beep input device when no beep is available
Takashi Iwai [Wed, 28 Jul 2010 15:37:16 +0000]
ALSA: hda - Don't register beep input device when no beep is available

We check now the availability of PC beep and skip the build of beep
mixers, but the driver still registers the input device.  This should
be checked as well.

Signed-off-by: Takashi Iwai <tiwai@suse.de>

9 years agodavinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
Sekhar Nori [Mon, 12 Jul 2010 12:26:21 +0000]
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high

Per the da850/omap-l138 Beta EVM SOM schematic, the DEFDCDC2 and
DEFDCDC3 lines are tied high. This leads to a 3.3V IO and 1.2V CVDD
voltage.

Pass the right platform data to the TPS6507x driver so it can operate
on the DEFDCDC{2,3}_HIGH register to read and change voltage levels.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoregulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
Anuj Aggarwal [Mon, 12 Jul 2010 12:24:06 +0000]
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register

Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

In TPS6507x, depending on the status of DEFDCDC{2,3} pin either
DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or
programmed to change the output voltage.

The current driver assumes DEFDCDC{2,3} pins are always tied low
and thus operates only on DEFDCDC{2,3}_LOW register. This need
not always be the case (as is found on OMAP-L138 EVM).

Unfortunately, software cannot read the status of DEFDCDC{2,3} pins.
So, this information is passed through platform data depending on
how the board is wired.

Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoALSA: hda - Fix pin-detection of Nvidia HDMI
Takashi Iwai [Wed, 28 Jul 2010 12:21:55 +0000]
ALSA: hda - Fix pin-detection of Nvidia HDMI

The behavior of Nvidia HDMI codec regarding the pin-detection unsol events
is based on the old HD-audio spec, i.e. PD bit indicates only the update
and doesn't show the current state.  Since the current code assumes the
new behavior, the pin-detection doesn't work relialby with these h/w.

This patch adds a flag for indicating the old spec, and fixes the issue
by checking the pin-detection explicitly for such hardware.

Tested-by: Wei Ni <wni@nvidia.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

9 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh...
Linus Torvalds [Tue, 27 Jul 2010 21:32:59 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/ericvh/v9fs

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: Pass the correct end of buffer to p9stat_read

9 years agogpio: fix spurious printk when freeing a gpio
Jon Povey [Tue, 27 Jul 2010 20:18:06 +0000]
gpio: fix spurious printk when freeing a gpio

When freeing a gpio that has not been exported, gpio_unexport() prints a
debug message when it should just fall through silently.

Example spurious message:

gpio_unexport: gpio0 status -22

Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
Cc: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

9 years agoedac: mpc85xx: fix coldplug/hotplug module autoloading
Anton Vorontsov [Tue, 27 Jul 2010 20:18:05 +0000]
edac: mpc85xx: fix coldplug/hotplug module autoloading

The MPC85xx EDAC driver is missing module device aliases, so the driver
won't load automatically on boot.  This patch fixes the issue by adding
proper MODULE_DEVICE_TABLE() macros.

Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Dave Jiang <djiang@mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

9 years agodrivers/rtc/rtc-rx8581.c: fix setdatetime
Rudolf Marek [Tue, 27 Jul 2010 20:18:02 +0000]
drivers/rtc/rtc-rx8581.c: fix setdatetime

Fix the logic while writing new date/time to the chip.  The driver
incorrectly wrote back register values to different registers and even
with wrong mask.  The patch adds clearing of the VLF register, which
should be cleared if all date/time values are set.

Signed-off-by: Rudolf Marek <rudolf.marek@sysgo.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Martyn Welch <martyn.welch@gefanuc.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

9 years agodynamic debug: move ddebug_remove_module() down into free_module()
Jason Baron [Tue, 27 Jul 2010 20:18:01 +0000]
dynamic debug: move ddebug_remove_module() down into free_module()

The command

echo "file ec.c +p" >/sys/kernel/debug/dynamic_debug/control

causes an oops.

Move the call to ddebug_remove_module() down into free_module().  In this
way it should be called from all error paths.  Currently, we are missing
the remove if the module init routine fails.

Signed-off-by: Jason Baron <jbaron@redhat.com>
Reported-by: Thomas Renninger <trenn@suse.de>
Tested-by: Thomas Renninger <trenn@suse.de>
Cc: <stable@kernel.org> [2.6.32+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

9 years agoceph: use complete_all and wake_up_all
Yehuda Sadeh [Tue, 27 Jul 2010 20:11:08 +0000]
ceph: use complete_all and wake_up_all

This fixes an issue triggered by running concurrent syncs. One of the syncs
would go through while the other would just hang indefinitely. In any case, we
never actually want to wake a single waiter, so the *_all functions should
be used.

Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>

9 years ago9p: Pass the correct end of buffer to p9stat_read
Latchesar Ionkov [Mon, 19 Jul 2010 20:40:03 +0000]
9p: Pass the correct end of buffer to p9stat_read

Pass the correct end of the buffer to p9stat_read.

Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>

9 years ago[S390] etr: fix clock synchronization race
Martin Schwidefsky [Tue, 27 Jul 2010 17:29:38 +0000]
[S390] etr: fix clock synchronization race

The etr events switch-to-local and sync-check disable the synchronous clock
and schedule a work queue that tries to get the clock back into sync.
If another switch-to-local or sync-check event occurs while the work queue
function etr_work_fn still runs the eacr.es bit and the clock_sync_word can
become inconsistent because check_sync_clock only uses the clock_sync_word
to determine if the clock is in sync or not. The second pass of the
etr_work_fn will reset the eacr.es bit but will leave the clock_sync_word
intact. Fix this race by moving the reset of the eacr.es bit into the
switch-to-local and sync-check functions and by checking the eacr.es bit
as well to decide if the clock needs to be synced.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

9 years ago[S390] Fix IRQ tracing in case of PER
Heiko Carstens [Tue, 27 Jul 2010 17:29:37 +0000]
[S390] Fix IRQ tracing in case of PER

In case user space is single stepped (PER) the program check handler
claims too early that IRQs are enabled on the return path.
Subsequent checks will notice that the IRQ mask in the PSW and
what lockdep thinks the IRQ mask should be do not correlate and
therefore will print a warning to the console and disable lockdep.

Fix this by doing all the work within the correct context.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

9 years ago[SCSI] ibmvscsi: Fix oops when an interrupt is pending during probe
Anton Blanchard [Tue, 13 Jul 2010 04:59:29 +0000]
[SCSI] ibmvscsi: Fix oops when an interrupt is pending during probe

A driver needs to be ready to take an interrupt as soon as it registers
an interrupt handler. I noticed the following oops when testing kdump:

ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
ibmvscsi 30000002: SRP_VERSION: 16.a
ibmvscsi 30000002: SRP_VERSION: 16.a
Unable to handle kernel paging request for data at address 0x00000000
...
pc: c000000004085e34: .tasklet_action+0xf4/0x1dc
...
c000000004086fe4 .__do_softirq+0x16c/0x2c0
c00000000403138c .call_do_softirq+0x14/0x24
c00000000400ee14 .do_softirq+0xa0/0x104
c00000000408690c .irq_exit+0x70/0xd0
c00000000400f190 .do_IRQ+0x214/0x2a8
c000000004004804 hardware_interrupt_entry+0x1c/0x98
--- Exception: 501 (Hardware Interrupt) at c00000000400c544 .raw_local_irq_restore+0x48/0x54
c00000000465d2a8 ._raw_spin_unlock_irqrestore+0x74/0xa0
c0000000040e7f00 .__setup_irq+0x2ec/0x3f0
c0000000040e8198 .request_threaded_irq+0x194/0x22c
c00000000446d854 .rpavscsi_init_crq_queue+0x284/0x3f0
c00000000446c764 .ibmvscsi_probe+0x688/0x710
c00000000402903c .vio_bus_probe+0x37c/0x3e4
c000000004403f10 .driver_probe_device+0xec/0x1b8
c000000004404088 .__driver_attach+0xac/0xf4
c000000004403184 .bus_for_each_dev+0x98/0x104
c000000004403c98 .driver_attach+0x40/0x60
c0000000044026f0 .bus_add_driver+0x154/0x324
c0000000044045d0 .driver_register+0xe8/0x1ac
c00000000402b2a8 .vio_register_driver+0x54/0x74
c000000004933ea4 .ibmvscsi_module_init+0x80/0xc0
c000000004009834 .do_one_initcall+0x98/0x1d8
c0000000049005b4 .kernel_init+0x27c/0x33c
c000000004031550 .kernel_thread+0x54/0x70

srp_task needs to be setup before request_irq. The patch below fixes the oops.

Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

9 years agoMerge branch 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/perf
Linus Torvalds [Tue, 27 Jul 2010 16:23:39 +0000]
Merge branch 'urgent' of git://git./linux/kernel/git/paulus/perf

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/perf:
  perf, powerpc: Use perf_sample_data_init() for the FSL code

9 years agoMerge git://git.infradead.org/users/cbou/battery-2.6.35
Linus Torvalds [Tue, 27 Jul 2010 16:22:55 +0000]
Merge git://git.infradead.org/users/cbou/battery-2.6.35

* git://git.infradead.org/users/cbou/battery-2.6.35:
  ds2782_battery: Rename get_current to fix build failure / name conflict

9 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Tue, 27 Jul 2010 16:21:00 +0000]
Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  s2io: fixing DBG_PRINT() macro
  ath9k: fix dma direction for map/unmap in ath_rx_tasklet
  net: dev_forward_skb should call nf_reset
  net sched: fix race in mirred device removal
  tun: avoid BUG, dump packet on GSO errors
  bonding: set device in RLB ARP packet handler
  wimax/i2400m: Add PID & VID for Intel WiMAX 6250
  ipv6: Don't add routes to ipv6 disabled interfaces.
  net: Fix skb_copy_expand() handling of ->csum_start
  net: Fix corruption of skb csum field in pskb_expand_head() of net/core/skbuff.c
  macvtap: Limit packet queue length
  ixgbe/igb: catch invalid VF settings
  bnx2x: Advance a module version
  bnx2x: Protect statistics ramrod and sequence number
  bnx2x: Protect a SM state change
  wireless: use netif_rx_ni in ieee80211_send_layer2_update

9 years agoperf, powerpc: Use perf_sample_data_init() for the FSL code
Peter Zijlstra [Fri, 9 Jul 2010 08:21:21 +0000]
perf, powerpc: Use perf_sample_data_init() for the FSL code

We should use perf_sample_data_init() to initialize struct
perf_sample_data.  As explained in the description of commit dc1d628a
("perf: Provide generic perf_sample_data initialization"), it is
possible for userspace to get the kernel to dereference data.raw,
so if it is not initialized, that means that unprivileged userspace
can possibly oops the kernel.  Using perf_sample_data_init makes sure
it gets initialized to NULL.

This conversion should have been included in commit dc1d628a, but it
got missed.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

9 years agowm8350-regulator: fix wm8350_register_regulator error handling
Axel Lin [Mon, 26 Jul 2010 02:41:58 +0000]
wm8350-regulator: fix wm8350_register_regulator error handling

In the case of platform_device_add() fail, we should call
platform_device_put() instead of platform_device_del()

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoab3100: fix off-by-one value range checking for voltage selector
Axel Lin [Mon, 26 Jul 2010 07:34:14 +0000]
ab3100: fix off-by-one value range checking for voltage selector

We use voltage selector as an array index for typ_voltages.
Thus the valid range for voltage selector should be 0..voltages_len-1.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoMerge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Mon, 26 Jul 2010 23:02:07 +0000]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Do not try to disable hpet if it hasn't been initialized before
  x86, i8259: Only register sysdev if we have a real 8259 PIC

9 years agos2io: fixing DBG_PRINT() macro
Breno Leitao [Mon, 26 Jul 2010 22:37:30 +0000]
s2io: fixing DBG_PRINT() macro

Patch 9e39f7c5b311a306977c5471f9e2ce4c456aa038 changed the
DBG_PRINT() macro and the if clause was wrongly changed. It means
that currently all the DBG_PRINT are being printed, flooding the
kernel log buffer with things like:

s2io: eth6: Next block at: c0000000b9c90000
s2io: eth6: In Neterion Tx routine

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

9 years agoMerge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
Linus Torvalds [Mon, 26 Jul 2010 22:35:53 +0000]
Merge branch 'fixes' of git://git./linux/kernel/git/davej/cpufreq

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] powernow-k8: Limit Pstate transition latency check
  [CPUFREQ] Fix PCC driver error path
  [CPUFREQ] fix double freeing in error path of pcc-cpufreq
  [CPUFREQ] pcc driver should check for pcch method before calling _OSC
  [CPUFREQ] fix memory leak in cpufreq_add_dev
  [CPUFREQ] revert "[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)"

9 years agoMerge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
Linus Torvalds [Mon, 26 Jul 2010 22:35:04 +0000]
Merge branch 'upstream' of git://git.linux-mips.org/upstream-linus

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Set io_map_base for several PCI bridges lacking it
  MIPS: Alchemy: Define eth platform devices in the correct order
  MIPS: BCM63xx: Prevent second enet registration on BCM6338
  MIPS: Quit using undefined behavior of ADDU in 64-bit atomic operations.
  MIPS: N32: Define getdents64.
  MIPS: MTX-1: Fix PCI on the MeshCube and related boards
  MIPS: Make init_vdso a subsys_initcall.
  MIPS: "Fix" useless 'init_vdso successfully' message.
  MIPS: PowerTV: Move register setup to before reading registers.
  SOUND: Au1000: Fix section mismatch
  VIDEO: Au1100fb: Fix section mismatch
  VIDEO: PMAGB-B: Fix section mismatch
  VIDEO: PMAG-BA: Fix section mismatch
  NET: declance: Fix section mismatches
  VIDEO. gbefb: Fix section mismatches.

9 years agodrm/i915: make sure we shut off the panel in eDP configs
Jesse Barnes [Mon, 26 Jul 2010 20:51:22 +0000]
drm/i915: make sure we shut off the panel in eDP configs

Fix error from the last pull request.  Making sure we shut the panel off
is more correct and saves power.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

9 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Mon, 26 Jul 2010 20:26:09 +0000]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

9 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6
Linus Torvalds [Mon, 26 Jul 2010 20:07:25 +0000]
Merge git://git./linux/kernel/git/gregkh/driver-core-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  sysfs: allow creating symlinks from untagged to tagged directories
  sysfs: sysfs_delete_link handle symlinks from untagged to tagged directories.
  sysfs: Don't allow the creation of symlinks we can't remove

9 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
Linus Torvalds [Mon, 26 Jul 2010 20:06:39 +0000]
Merge git://git./linux/kernel/git/gregkh/usb-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: musb: tusb6010: fix compile error with n8x0_defconfig
  USB: FTDI: Add support for the RT System VX-7 radio programming cable
  USB: add quirk for Broadcom BT dongle
  USB: usb-storage: fix initializations of urb fields
  USB: xhci: Set Mult field in endpoint context correctly.
  USB: sisusbvga: Fix for USB 3.0
  USB: adds Artisman USB dongle to list of quirky devices
  USB: xhci: Set EP0 dequeue ptr after reset of configured device.
  USB: Fix USB3.0 Port Speed Downgrade after port reset
  USB: xHCI: Fix another bug in link TRB activation change.
  USB: option: Add support for AMOI Skypephone S2
  USB: New PIDs for Qualcomm gobi 2000 (qcserial)
  USB: ftdi_sio: support for Signalyzer tools based on FTDI chips
  USB: s3c2410_udc: be aware of connected gadget driver
  USB: Expose vendor-specific ACM channel on Nokia 5230
  USB: Add PID for Sierra 250U to drivers/usb/serial/sierra.c
  USB: option: add support for 1da5:4518

9 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
Linus Torvalds [Mon, 26 Jul 2010 20:06:25 +0000]
Merge git://git./linux/kernel/git/gregkh/tty-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: fix rs485 for atmel_serial on avr32

9 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt...
Linus Torvalds [Mon, 26 Jul 2010 20:04:25 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/anholt/drm-intel

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: add pipe A force quirks to i915 driver
  drm/i915: Fix panel fitting regression since 734b4157
  drm/i915: fix deadlock in fb teardown
  drm/i915: don't free non-existent compressed llb on ILK+
  agp/intel: Use the correct mask to detect i830 aperture size.
  drm/i915: disable FBC when more than one pipe is active
  drm/i915: Use the correct scanout alignment for fbcon.
  drm/i915: make sure eDP panel is turned on
  drm/i915: add PANEL_UNLOCK_REGS definition
  drm/i915: Make G4X-style PLL search more permissive
  drm/i915: Clear any existing dither mode prior to enabling spatial dithering
  drm/i915: handle shared framebuffers when flipping
  drm/i915: Explosion following OOM in do_execbuffer.
  gpu/drm/i915: Add a blacklist to omit modeset on LID open

9 years ago[CPUFREQ] powernow-k8: Limit Pstate transition latency check
Borislav Petkov [Thu, 8 Jul 2010 15:55:30 +0000]
[CPUFREQ] powernow-k8: Limit Pstate transition latency check

The Pstate transition latency check was added for broken F10h BIOSen
which wrongly contain a value of 0 for transition and bus master
latency. Fam11h and later, however, (will) have similar transition
latency so extend that behavior for them too.

Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>

9 years ago[CPUFREQ] Fix PCC driver error path
Matthew Garrett [Thu, 15 Jul 2010 15:44:00 +0000]
[CPUFREQ] Fix PCC driver error path

The PCC cpufreq driver unmaps the mailbox address range if any CPUs fail to
initialise, but doesn't do anything to remove the registered CPUs from the
cpufreq core resulting in failures further down the line. We're better off
simply returning a failure - the cpufreq core will unregister us cleanly if
we end up with no successfully registered CPUs. Tidy up the failure path
and also add a sanity check to ensure that the firmware gives us a realistic
frequency - the core deals badly with that being set to 0.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Signed-off-by: Dave Jones <davej@redhat.com>

9 years ago[CPUFREQ] fix double freeing in error path of pcc-cpufreq
Daniel J Blueman [Fri, 23 Jul 2010 22:06:52 +0000]
[CPUFREQ] fix double freeing in error path of pcc-cpufreq

Prevent double freeing on error path.

Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>

9 years ago[CPUFREQ] pcc driver should check for pcch method before calling _OSC
Matthew Garrett [Tue, 20 Jul 2010 17:52:00 +0000]
[CPUFREQ] pcc driver should check for pcch method before calling _OSC

The pcc specification documents an _OSC method that's incompatible with the
one defined as part of the ACPI spec. This shouldn't be a problem as both
are supposed to be guarded with a UUID. Unfortunately approximately nobody
(including HP, who wrote this spec) properly check the UUID on entry to the
_OSC call. Right now this could result in surprising behaviour if the pcc
driver performs an _OSC call on a machine that doesn't implement the pcc
specification. Check whether the PCCH method exists first in order to reduce
this probability.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Signed-off-by: Dave Jones <davej@redhat.com>

9 years ago[CPUFREQ] fix memory leak in cpufreq_add_dev
Xiaotian Feng [Tue, 20 Jul 2010 12:11:02 +0000]
[CPUFREQ] fix memory leak in cpufreq_add_dev

We didn't free policy->related_cpus in error path err_unlock_policy.
This is catched by following kmemleak report:

unreferenced object 0xffff88022a0b96d0 (size 512):
  comm "modprobe", pid 886, jiffies 4294689177 (age 780.694s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff8111ebe5>] create_object+0x186/0x281
    [<ffffffff814fad4f>] kmemleak_alloc+0x60/0xa7
    [<ffffffff8111127a>] kmem_cache_alloc_node_notrace+0x120/0x142
    [<ffffffff81262e4f>] alloc_cpumask_var_node+0x2c/0xd7
    [<ffffffff81262f0b>] alloc_cpumask_var+0x11/0x13
    [<ffffffff81262f1c>] zalloc_cpumask_var+0xf/0x11
    [<ffffffff8140fac0>] cpufreq_add_dev+0x11f/0x547
    [<ffffffff81334bda>] sysdev_driver_register+0xc2/0x11d
    [<ffffffff8140e334>] cpufreq_register_driver+0xcb/0x1b8
    [<ffffffffa032e040>] 0xffffffffa032e040
    [<ffffffff810021ba>] do_one_initcall+0x5e/0x15c
    [<ffffffff81087f94>] sys_init_module+0xa6/0x1e6
    [<ffffffff81009bc2>] system_call_fastpath+0x16/0x1b
    [<ffffffffffffffff>] 0xffffffffffffffff

Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>

9 years ago[CPUFREQ] revert "[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second...
Andrej Gelenberg [Fri, 14 May 2010 22:15:58 +0000]
[CPUFREQ] revert "[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)"

395913d0b1db37092ea3d9d69b832183b1dd84c5 ("[CPUFREQ] remove rwsem lock
from CPUFREQ_GOV_STOP call (second call site)") is not needed, because
there is no rwsem lock in cpufreq_ondemand and cpufreq_conservative
anymore.  Lock should not be released until the work done.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=1594

Signed-off-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Dave Jones <davej@redhat.com>

9 years agosysfs: allow creating symlinks from untagged to tagged directories
Eric W. Biederman [Wed, 21 Jul 2010 05:12:01 +0000]
sysfs: allow creating symlinks from untagged to tagged directories

Supporting symlinks from untagged to tagged directories is reasonable,
and needed to support CONFIG_SYSFS_DEPRECATED.  So don't fail a prior
allowing that case to work.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agosysfs: sysfs_delete_link handle symlinks from untagged to tagged directories.
Eric W. Biederman [Wed, 21 Jul 2010 05:10:58 +0000]
sysfs: sysfs_delete_link handle symlinks from untagged to tagged directories.

This happens for network devices when SYSFS_DEPRECATED is enabled.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agosysfs: Don't allow the creation of symlinks we can't remove
Eric W. Biederman [Thu, 8 Jul 2010 16:31:24 +0000]
sysfs: Don't allow the creation of symlinks we can't remove

Recently my tagged sysfs support revealed a flaw in the device core
that a few rare drivers are running into such that we don't always put
network devices in a class subdirectory named net/.

Since we are not creating the class directory the network devices wind
up in a non-tagged directory, but the symlinks to the network devices
from /sys/class/net are in a tagged directory.  All of which works
until we go to remove or rename the symlink.  When we remove or rename
a symlink we look in the namespace of the target of the symlink.
Since the target of the symlink is in a non-tagged sysfs directory we
don't have a namespace to look in, and we fail to remove the symlink.

Detect this problem up front and simply don't create symlinks we won't
be able to remove later.  This prevents symlink leakage and fails in
a much clearer and more understandable way.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: musb: tusb6010: fix compile error with n8x0_defconfig
Felipe Balbi [Mon, 5 Jul 2010 09:12:01 +0000]
USB: musb: tusb6010: fix compile error with n8x0_defconfig

Drop the unnecessary empty stubs in tusb6010.c and avoid
a compile error when building kernel for n8x0.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: FTDI: Add support for the RT System VX-7 radio programming cable
Corey Minyard [Wed, 21 Jul 2010 13:39:22 +0000]
USB: FTDI: Add support for the RT System VX-7 radio programming cable

RT Systems has put out bunch of ham radio cables based on the FT232RL
chip.  Each cable type has a unique PID, this adds one for the Yaesu VX-7
radios.

Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: add quirk for Broadcom BT dongle
Oliver Neukum [Wed, 14 Jul 2010 16:26:22 +0000]
USB: add quirk for Broadcom BT dongle

This device needs to be reset when resuming

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: usb-storage: fix initializations of urb fields
Bob Copeland [Mon, 12 Jul 2010 15:18:18 +0000]
USB: usb-storage: fix initializations of urb fields

Commit 0ede76fcec5415ef82a423a95120286895822e2d, "USB: remove uses of
URB_NO_SETUP_DMA_MAP" introduced a regression by inadvertantly removing
initialization of the transfer flags.  This caused initialization
failures in the ums-karma driver.  Fix the regression by zeroing it.

While at it, as Alan Stern points out, the initializers for
actual_length and status are handled by the core and error_count
only matters for isochronous urbs, so they don't need to be set here.
Remove them.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: xhci: Set Mult field in endpoint context correctly.
Sarah Sharp [Sat, 10 Jul 2010 13:48:01 +0000]
USB: xhci: Set Mult field in endpoint context correctly.

The bmAttributes field of the SuperSpeed Endpoint Companion Descriptor has
different meanings, depending on the endpoint type.  If the endpoint is
isochronous, the bmAttributes field is the maximum number of packets
within a service interval that this endpoint supports.  If the endpoint is
bulk, it's the number of stream IDs this endpoint supports.

Only set the Mult field of the xHCI endpoint context using the
bmAttributes field if the endpoint is isochronous, and the device is a
SuperSpeed device.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: sisusbvga: Fix for USB 3.0
Oliver Neukum [Fri, 16 Jul 2010 15:36:26 +0000]
USB: sisusbvga: Fix for USB 3.0

Super speed is also fast enough to let sisusbvga operate.
Therefor expand the checks.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: adds Artisman USB dongle to list of quirky devices
Paul Mortier [Fri, 9 Jul 2010 12:18:50 +0000]
USB: adds Artisman USB dongle to list of quirky devices

When an attempt is made to read the interface strings of the Artisman
Watchdog USB dongle (idVendor:idProduct 04b4:0526) an error is written
to the dmesg log (uhci_result_common: failed with status 440000) and the
dongle resets itself, resulting in a disconnect/reconnect loop.

Adding the dongle to the list of devices in quirks.c, with the same
quirk Alan Stern's previous patch for the Saitek Cyborg Gold 3D
joystick, stops the device from resetting and allows it to be used with
no problems.

Signed-off-by: Paul Mortier <mortier@btinternet.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: xhci: Set EP0 dequeue ptr after reset of configured device.
Sarah Sharp [Fri, 9 Jul 2010 15:08:54 +0000]
USB: xhci: Set EP0 dequeue ptr after reset of configured device.

When a configured device is reset, the control endpoint's ring is reused.
If control transfers to the device were issued before the device is reset,
the dequeue pointer will be somewhere in the middle of the ring.  If the
device is then issued an address with the set address command, the xHCI
driver must provide a valid input context for control endpoint zero.

The original code would give the hardware the original input context,
which had a dequeue pointer set to the top of the ring.  This would cause
the host to re-execute any control transfers until it reached the ring's
enqueue pointer.  When issuing a set address command for a device that has
just been configured and then reset, use the control endpoint's enqueue
pointer as the hardware's dequeue pointer.

Assumption:  All control transfers will be completed or cancelled before
the set address command is issued to the device.  If there are any
outstanding control transfers, this code will not work.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: Fix USB3.0 Port Speed Downgrade after port reset
Sarah Sharp [Fri, 9 Jul 2010 15:08:48 +0000]
USB: Fix USB3.0 Port Speed Downgrade after port reset

Without this fix, a USB 3.0 port is downgraded to full speed after a port
reset of a configured device.  The USB 3.0 terminations will be disabled
permanently, and USB 3.0 devices will always enumerate as full speed
devices, until the host controller is unplugged (if it is an ExpressCard)
or the computer is rebooted.

Fajun Chen traced this traced the speed downgrade issue to the port reset
and the interpretation of port status in USB hub driver code.  The hub
code was not testing for the port being a SuperSpeed port, and it fell
through to the else case of Full Speed.

The following patch adds SuperSpeed mapping from the port status, and
fixes the speed downgrade issue.

Reported-by: Fajun Chen <fajun.chen@seagate.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: xHCI: Fix another bug in link TRB activation change.
Sarah Sharp [Fri, 9 Jul 2010 15:08:38 +0000]
USB: xHCI: Fix another bug in link TRB activation change.

Commit 6c12db90f19727c76990e7f4801c67a148b30111 also seems to have
introduced a bug that is triggered when the command ring is about to wrap.
The inc_enq() function will not have moved the enqueue pointer past the
link TRB.  It is supposed to be moved past the link TRB in prepare_ring(),
which should be called before a TD is enqueued.  However, the
queue_command() function never calls the prepare_ring() function because
prepare_ring() is only supposed to be used for endpoint rings.  That means
the enqueue pointer will not be moved past the link TRB, and will get
overwritten.

The fix is to make queue_command() call prepare_ring() with a fake
endpoint status (set to running).  Then the enqueue pointer will get moved
past the link TRB.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: option: Add support for AMOI Skypephone S2
Dennis Jansen [Fri, 9 Jul 2010 20:03:53 +0000]
USB: option: Add support for AMOI Skypephone S2

usbserial: Add AMOI Skypephone S2 support.

This patch adds support for the AMOI Skypephone S2 to the usbserial module.

Tested-by: Dennis Jansen <Dennis.Jansen@web.de>
Signed-off-by: Dennis Jansen <Dennis.Jansen@web.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: New PIDs for Qualcomm gobi 2000 (qcserial)
Andrew Bird [Thu, 1 Jul 2010 19:50:07 +0000]
USB: New PIDs for Qualcomm gobi 2000 (qcserial)

Adds support for the Generic Qualcomm Gobi 2000 WWAN UMTS/CDMA modem

Signed-off-by: Andrew Bird <ajb@spheresytems.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: ftdi_sio: support for Signalyzer tools based on FTDI chips
Colin Leitner [Thu, 1 Jul 2010 08:49:55 +0000]
USB: ftdi_sio: support for Signalyzer tools based on FTDI chips

ftdi_sio: support for Signalyzer tools based on FTDI chips

This patch adds support for the Xverve Signalyzers.

Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: s3c2410_udc: be aware of connected gadget driver
Vladimir Zapolskiy [Tue, 29 Jun 2010 19:36:26 +0000]
USB: s3c2410_udc: be aware of connected gadget driver

To escape from data abort in interrupt handler, it is required to
check for a connected gadget before delivering control requests.

The change fixes the following panic, which occurs with no loaded
gadget driver and input USB_REQ_GET_DESCRIPTOR request:

Kernel panic - not syncing: Fatal exception in interrupt
[<c0025874>] (unwind_backtrace+0x0/0xd8) from [<c0253f14>] (panic+0x40/0x110)
[<c0253f14>] (panic+0x40/0x110) from [<c002470c>] (die+0x154/0x180)
[<c002470c>] (die+0x154/0x180) from [<c0026448>] (__do_kernel_fault+0x64/0x74)
[<c0026448>] (__do_kernel_fault+0x64/0x74) from [<c0026610>] (do_page_fault+0x1b8/0x1cc)
[<c0026610>] (do_page_fault+0x1b8/0x1cc) from [<c00202d4>] (do_DataAbort+0x34/0x94)
[<c00202d4>] (do_DataAbort+0x34/0x94) from [<c0020a60>] (__dabt_svc+0x40/0x60)
Exception stack(0xc0327ea8 to 0xc0327ef0)
7ea0:                   bf0026b0 c0327ef0 c0327ee4 00000000 bf002590 00000093
7ec0: 00000001 bf0026b0 bf002990 00000000 00000008 0000143d 00003f00 c0327ef0
7ee0: bf001364 bf001360 20000093 ffffffff
[<c0020a60>] (__dabt_svc+0x40/0x60) from [<bf001360>] (s3c2410_udc_irq+0x5b8/0x778 [s3c2410_udc])
[<bf001360>] (s3c2410_udc_irq+0x5b8/0x778 [s3c2410_udc]) from [<c0058aa0>] (handle_IRQ_event+0x3c/0x104)
[<c0058aa0>] (handle_IRQ_event+0x3c/0x104) from [<c005a428>] (handle_edge_irq+0x12c/0x164)
[<c005a428>] (handle_edge_irq+0x12c/0x164) from [<c0020068>] (asm_do_IRQ+0x68/0x88)
[<c0020068>] (asm_do_IRQ+0x68/0x88) from [<c0020aa4>] (__irq_svc+0x24/0xa0)

Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: Expose vendor-specific ACM channel on Nokia 5230
Przemo Firszt [Mon, 28 Jun 2010 20:29:34 +0000]
USB: Expose vendor-specific ACM channel on Nokia 5230

Nokia S60 phones expose two ACM channels. The first is
a modem, the second is 'vendor-specific' but is treated
as a serial device at the S60 end, so we want to expose
it on Linux too.

Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: Add PID for Sierra 250U to drivers/usb/serial/sierra.c
august huber [Mon, 28 Jun 2010 18:46:05 +0000]
USB: Add PID for Sierra 250U to drivers/usb/serial/sierra.c

Add VID/PID for Sierra Wireless 250U USB dongle to sierra.c
Allows use of 3G radio only

Signed-off-by: August Huber <gus@pbx.org>
Cc: Elina Pasheva <epasheva@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoUSB: option: add support for 1da5:4518
Ă–mer Sezgin Ugurlu [Mon, 28 Jun 2010 16:01:58 +0000]
USB: option: add support for 1da5:4518

Signed-off-by: Omer Sezgin Ugurlu <omer.ugurlu@a-kent.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agodrm/i915: add pipe A force quirks to i915 driver
Jesse Barnes [Mon, 19 Jul 2010 20:53:12 +0000]
drm/i915: add pipe A force quirks to i915 driver

Ported over from the old UMS list.  Unfortunately they're still
necessary especially on older laptop platforms.

Fixes https://bugs.freedesktop.org/show_bug.cgi?id=22126.

Tested-by: Xavier <shiningxc@gmail.com>
Tested-by: Diego Escalante Urrelo <diegoe@gnome.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>

9 years agodrm/i915: Fix panel fitting regression since 734b4157
Chris Wilson [Sat, 17 Jul 2010 11:43:20 +0000]
drm/i915: Fix panel fitting regression since 734b4157

The crtc mode fixup is run after the encoders adjust the mode to fit on
their output, so don't reset the mode!

Fixes:

  Bug 29057 - display corruption under 800x600 on netbook
              (1024x600) with 'Full Aspect' scaling
  https://bugs.freedesktop.org/show_bug.cgi?id=29057

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Xun Fang <xunx.fang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

9 years agoserial: fix rs485 for atmel_serial on avr32
Peter Huewe [Tue, 29 Jun 2010 17:35:39 +0000]
serial: fix rs485 for atmel_serial on avr32

This patch fixes a build failure [1-4] in the atmel_serial code introduced by
patch the patch ARM: 6092/1: atmel_serial: support for RS485
communications (e8faff7330a3501eafc9bfe5f4f15af444be29f5)

The build failure was caused by missing struct field and missing defines
for the avr32 board - the patch fixes this.

[1] http://kisskb.ellerman.id.au/kisskb/buildresult/2575242/ - first failure in linux-next, may 11th
[2] http://kisskb.ellerman.id.au/kisskb/buildresult/2816418/ - still exists as of today
[3] http://kisskb.ellerman.id.au/kisskb/buildresult/2617511/ - first failure in Linus' tree - May 20th - did really no one notice this?!
[4] http://kisskb.ellerman.id.au/kisskb/buildresult/2813956/ - still exists in Linus' tree as of today

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9 years agoath9k: fix dma direction for map/unmap in ath_rx_tasklet
Ming Lei [Fri, 14 May 2010 13:15:38 +0000]
ath9k: fix dma direction for map/unmap in ath_rx_tasklet

For edma, we should use DMA_BIDIRECTIONAL, or else use
DMA_FROM_DEVICE.

This is found to address "BUG at arch/x86/mm/physaddr.c:5"
as described here:

http://lkml.org/lkml/2010/7/14/21

Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>