9 years agoASoC: Remove unneeded suspend bias managment from CODEC drivers
Mark Brown [Fri, 7 May 2010 19:30:00 +0000]
ASoC: Remove unneeded suspend bias managment from CODEC drivers

The core will ensure that the device is in either STANDBY or OFF bias
before suspending, restoring the bias in the driver is unneeded. Some
drivers doing slightly more roundabout things have been left alone
for now.

Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: SMDK64XX: Switch to IISv4 CPU driver
Jassi Brar [Tue, 27 Apr 2010 06:57:17 +0000]
ASoC: SMDK64XX: Switch to IISv4 CPU driver

Switch the MACHINE driver to use IISv4 CPU dai.
Remove BROKEN dependency now that we have proper CPU driver available.
Also, disable build for SMDK6400, since the S3C6400 doesn't have IISv4
controller.

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: S3C64XX: IISv4: Add CPU driver
Jassi Brar [Tue, 27 Apr 2010 06:57:11 +0000]
ASoC: S3C64XX: IISv4: Add CPU driver

Add the CPU driver for the IISv4 block found on S3C6410.
For now, the driver is almost a copy of s3c64xx-i2s.c but
it should diverge as more IISv4 specific stuff is added.

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: tpa6130a2: Fix for the custom kcontrol functions
Peter Ujfalusi [Fri, 7 May 2010 11:24:11 +0000]
ASoC: tpa6130a2: Fix for the custom kcontrol functions

Since the functions arre only used for volume register,
change their name, and also fix them to properly
handle the cases, when via soc core the volume is
limited.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoRevert "ASoC: tpa6130a2: Support for limiting gain"
Peter Ujfalusi [Fri, 7 May 2010 11:24:10 +0000]
Revert "ASoC: tpa6130a2: Support for limiting gain"

This reverts commit 6f3991152f20933b77eff30413e893bf1a15e578.

Since core has now support for limiting the volume on controls this
patch is not needed.  Furthermore, this patch actually prevents the core
to set new volume on the TPA.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: core: Support for limiting the volume
Peter Ujfalusi [Fri, 7 May 2010 11:05:49 +0000]
ASoC: core: Support for limiting the volume

Add support for the core to limit the maximum volume on an
existing control.
The function will modify the soc_mixer_control.max value
of the given control.
The new value must be lower than the original one (chip maximum)

If there is a need for limiting a gain on a given control,
than machine drivers can do the following in their
snd_soc_dai_link.init function:

snd_soc_limit_volume(codec, "TPA6140A2 Headphone Playback Volume", 21);

This will modify the original 31 (chip maximum) to 21, so user
space will not be able to set the gain higher than this.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoMerge branch 'topic/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai...
Mark Brown [Fri, 7 May 2010 15:38:26 +0000]
Merge branch 'topic/asoc' of git://git./linux/kernel/git/tiwai/sound-2.6 into for-2.6.35

9 years agoARM: S3C2412: DMA: Remove I2S FIFO address
Jassi Brar [Fri, 7 May 2010 01:21:39 +0000]
ARM: S3C2412: DMA: Remove I2S FIFO address

The S3C DMA API doesn't make use of hw_addr.to/from and also
the FIFO addresses are provided from the I2S drivers. So these
fields are redundant.
This patch removes the hw_addr.to/from fields for I2S and the
inclusion of header, paving way for the header to be moved closer
to the I2S controller drivers.

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoMerge branch 'for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc...
Takashi Iwai [Thu, 6 May 2010 15:06:27 +0000]
Merge branch 'for-2.6.35' of git://git./linux/kernel/git/lrg/asoc-2.6 into topic/asoc

9 years agoASoC: tlv320dac33: Use codec defaults for LOM/LOP and DAC power
Peter Ujfalusi [Thu, 6 May 2010 09:04:25 +0000]
ASoC: tlv320dac33: Use codec defaults for LOM/LOP and DAC power

Do not change the codec defaults for the following registers:
0x40, 0x41: Line output gains, do not use amplification
0x42: LOM/LOP Voltage hold, and selection
0x44: LOM inversion control

It has been found, that the values configured to these registers
can cause amplification, which can make the output of DAC33
distorted.

The codec reset values are considered safe in all environmnts.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tpa6130a2: Support for limiting gain
Peter Ujfalusi [Thu, 6 May 2010 07:37:18 +0000]
ASoC: tpa6130a2: Support for limiting gain

Add support for platform dependent gain limiting on the
tpa6130a2 (and tpa6140a2) Headset amplifier.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320aic3x: Add platform data and reset gpio handling
Jarkko Nikula [Wed, 5 May 2010 10:02:03 +0000]
ASoC: tlv320aic3x: Add platform data and reset gpio handling

Handle the reset GPIO within the codec driver in order to follow
the startup protocol for the tlv320aic3x codecs.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: omap: Add basic audio support for Nokia RX-51/N900
Jarkko Nikula [Wed, 5 May 2010 08:14:22 +0000]
ASoC: omap: Add basic audio support for Nokia RX-51/N900

This patch adds support for integrated stereo speakers and digital
microphone found on Nokia RX-51 hardware. This is a cut down version based
on Maemo kernel sources and earlier patchset by Eduardo Valentin et al.

http://mailman.alsa-project.org/pipermail/alsa-devel/2009-October/022033.html

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: S3C: I2S: Move set_sysclk to common code
Jassi Brar [Tue, 27 Apr 2010 06:57:05 +0000]
ASoC: S3C: I2S: Move set_sysclk to common code

Now that we can specify feature of a particular controller, we can
avoid multiple copies of same code by defining the CDCLKCON bit
feature in controller specific code and detecting that flag in the
code common to all controllers.

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: S3C: I2Sv2: New field for controller feature
Jassi Brar [Tue, 27 Apr 2010 06:56:56 +0000]
ASoC: S3C: I2Sv2: New field for controller feature

In order to make s3c-i2s-v2.c manage controllers with minor
quirks and variation in features, we define a per-block flag
that indicates the availability/lack of a particular feature
to the s3c-i2s-v2.c

While adding support for new SoCs' I2S, check for the blocks
of older SoCs that have similar feature and set the flag for
that feature.

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: S3C64XX: I2S: Use s3c2412 defines
Jassi Brar [Tue, 27 Apr 2010 06:56:51 +0000]
ASoC: S3C64XX: I2S: Use s3c2412 defines

Now that the fields are defined for s3c2412, use them and avoid having
multiple copies of same defines.

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: S3C: I2Sv2: Unify i2s_get_clock callback
Jassi Brar [Tue, 27 Apr 2010 06:56:45 +0000]
ASoC: S3C: I2Sv2: Unify i2s_get_clock callback

Now that we have two callbacks s3c2412_i2s_get_clock & s3c64xx_i2s_get_clock
doing exactly the same thing, we can define one generic s3c_i2sv2_get_clock
and discard other two copies. Also, switch the users to make calls to the
newly defined and generic s3c_i2sv2_get_clock

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: S3C: I2Sv2: Discard redundant field iis_clk
Jassi Brar [Tue, 27 Apr 2010 06:56:39 +0000]
ASoC: S3C: I2Sv2: Discard redundant field iis_clk

No need to keep redundant field iis_clk in s3c_i2sv2_info.
iis_cclk and iis_pclk is all we need.

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: S3C2412: I2S: Return correct source clock
Jassi Brar [Tue, 27 Apr 2010 06:56:34 +0000]
ASoC: S3C2412: I2S: Return correct source clock

Until now, s3c2412_get_iisclk would return NULL since iis_clk was never
initialized.
Return appropriate pointer as per the selection made for source clock.

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: S3C2412: I2S: Debug IMS field
Jassi Brar [Tue, 27 Apr 2010 06:56:27 +0000]
ASoC: S3C2412: I2S: Debug IMS field

The IMS field of s3c2412/13 is essentially the same as that of s3c64xx.
That is, the IISMOD[11] bit decides Master/Slave mode and IISMOD[10] bit
selects source clock for signal generation.
For that reason, remove improper defines for IISMOD[11:10] field mask
and define two 1bit fields that can be set independent of each other.
As a consequence, corresponding fields for PLAT_S3C64XX too get to use
these new defines.

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: SAMSUNG: I2S: Add bit definitions
Jassi Brar [Tue, 27 Apr 2010 06:56:03 +0000]
ASoC: SAMSUNG: I2S: Add bit definitions

Define more bit definitions in the order of mainline
support for the SoC.

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: S3C: I2Sv2: Move defines closer to driver
Jassi Brar [Tue, 27 Apr 2010 06:55:21 +0000]
ASoC: S3C: I2Sv2: Move defines closer to driver

The header for I2Sv2
   linux/arch/arm/plat-s3c/include/plat/regs-s3c2412-iis.h
contains only controller specific definitions and nothing
SoC specific. So, it could be moved to sound/soc/s3c24xx/

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: Add debug output tracing all cache register writes
Mark Brown [Mon, 3 May 2010 15:25:52 +0000]
ASoC: Add debug output tracing all cache register writes

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tpa6130a2: TLV mapping for tpa6140a2
Peter Ujfalusi [Tue, 4 May 2010 08:08:18 +0000]
ASoC: tpa6130a2: TLV mapping for tpa6140a2

Both tpa6130a2, and tpa6140a2 is supported by the
same driver, but the gain dB scaling is different on
the amplifiers.

Provide different mixer control for the chips with correct
TLV mapping.

User space will see:
"TPA6130A2 Headphone Playback Volume" in case of 6130
"TPA6140A2 Headphone Playback Volume" in case of 6140

The way machine drivers are using this amplifier remained
the same.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320dac33: Support for turning off the codec
Peter Ujfalusi [Fri, 30 Apr 2010 11:59:36 +0000]
ASoC: tlv320dac33: Support for turning off the codec

Let the codec to hit OFF instead of STANDBY, when there is no activity.
When the codec is off, than the associated regulator can be also turned
off (if the number of users on the regulator is 0).

After initialization, the codec remains in power off, it is only turned
on for reading the ID registers (also testing the regulators).

The codec power is enabled, when the codec is moving from BIAS_OFF
to BIAS_STANDBY.
The codec is turned off, when it hits BIAS_OFF.

There are few scenarios, which has to be taken care::
1. Analog bypass caused BIAS_OFF -> BIAS_ON
   We need to power on the codec, and do the chip init, but we does not
   need to execute the playback related configuration
2. Playback caused  BIAS_OFF -> BIAS_ON
   We need to power on the codec, and do the chip init, and also we need
   to execute the playback related configuration.
3. Playback start, while Analog bypass is on (BIAS_ON -> BIAS_ON)
   We need to execute the playback related configuration. The codec is
   already on.
4. Analog bypass enable, while playback (BIAS_ON -> BIAS_ON)
   Nothing need to be done.
5. Playback start withing soc power down timeout (BIAS_ON -> BIAS_ON)
   We need to execute the playback related configuration. The codec is
   still on.

Since the power up, and the codec init is optimized, the added overhead
in stream start is minimal.

Withing this patch, the hard_power function is now only doing what it
supposed to: only handle the powers, and GPIO reset line.
The codec initialization and state restore has been moved out.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320dac33: Manage a pointer for snd_pcm_substream in private structure
Peter Ujfalusi [Fri, 30 Apr 2010 11:59:35 +0000]
ASoC: tlv320dac33: Manage a pointer for snd_pcm_substream in private structure

As a preparation for supporting codec to be turned off,
when we are in BIAS_STANDBY.

The substream must be easily available in other places than
pcm_* callbacks.

Manage a pointer in _startup, and _shutdown for this.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320dac33: Revised module loading, and DAC33 ID read
Peter Ujfalusi [Fri, 30 Apr 2010 11:59:34 +0000]
ASoC: tlv320dac33: Revised module loading, and DAC33 ID read

Optimize the way how tlv320dac33 is powered uppon module and
soc initialization.
Also read the DAC33 ID registers, and update the reg_cache
to reflect it.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320dac33: Optimize power up, and restore
Peter Ujfalusi [Fri, 30 Apr 2010 11:59:33 +0000]
ASoC: tlv320dac33: Optimize power up, and restore

On power up we only need to initialize the codec, and
restore only registers, which are not in either in DAPM
nor in the playback start sequence.
These are mostly gain related registers.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: TWL4030: Remove OUTL/R outputs
Peter Ujfalusi [Thu, 29 Apr 2010 07:58:09 +0000]
ASoC: TWL4030: Remove OUTL/R outputs

OUTL/R are leftovers from the original driver, and they
are no longer needed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: TWL4030: AIF/APLL fix in DAPM domain
Peter Ujfalusi [Thu, 29 Apr 2010 07:58:08 +0000]
ASoC: TWL4030: AIF/APLL fix in DAPM domain

This patch orders the APLL and AIF power sequence in
case of HiFi (audio in TWL4030 terms) playback/capture.

We also need to make sure that the AIF is running during
playback/capture, when there is no valid DAPM route
available. For this purpose I introduce these virtual
widgets:
/* To have complete playback route all the time */
DAPM_OUTPUT("Virtual HiFi OUT") /* Will keep AIF/APLL enabled */

/* To have complete capture route all the time */
DAPM_INPUT("Virtual HiFi IN") /* Will keep AIF/APLL enabled */

/* To have complete playback route for the voice module */
DAPM_OUTPUT("Virtual Voice OUT") /* Will keep APLL enabled */

The DAPM_SUPPLY widgets for APLL and AIF are placed in a way,
that during any audio activity the needed configuration of AIF
and APLL will be enabled (playback, capture, analog loopback,
digital loopback, and voice activity).

The apll reference counting code has been lifted,
and modified from Liam Girdwood's earlier patch.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: Add WM9090 amplifier driver
Mark Brown [Wed, 28 Apr 2010 17:36:10 +0000]
ASoC: Add WM9090 amplifier driver

The WM9090 is a high performance low power audio subsystem, including
headphone and class D speaker drivers.

Note that this driver is a standalone CODEC driver and so is only
immediately suitable for use with the WM9090 as a standalone sound card
taking line inputs, or with a DAC with no software control.  The pending
ASoC multi-CODEC support will expand the range of systems that can use
the driver, or system-specific adaptations can be made.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320dac33 - disable regulators at i2c remove()
Liam Girdwood [Fri, 26 Mar 2010 20:05:54 +0000]
ASoC: tlv320dac33 - disable regulators at i2c remove()

Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: zoom2 - update DAPM pins
Liam Girdwood [Mon, 22 Mar 2010 19:35:06 +0000]
ASoC: zoom2 - update DAPM pins

Remove bogus twl4030 pins

Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: pandora - update DAPM pins
Liam Girdwood [Mon, 22 Mar 2010 19:30:54 +0000]
ASoC: pandora - update DAPM pins

Remove bogus TWL4030 pins.

Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: Remove redundant WM8960 SYSCLKSEL clkdiv option
Mark Brown [Tue, 27 Apr 2010 19:01:56 +0000]
ASoC: Remove redundant WM8960 SYSCLKSEL clkdiv option

The SYSCLK source is automatically managed when configuring the PLL.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoMerge branch 'for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc...
Takashi Iwai [Tue, 27 Apr 2010 13:35:59 +0000]
Merge branch 'for-2.6.35' of git://git./linux/kernel/git/lrg/asoc-2.6 into topic/asoc

9 years agoASoC: tlv320aic3x: Add basic regulator support
Jarkko Nikula [Mon, 26 Apr 2010 12:49:14 +0000]
ASoC: tlv320aic3x: Add basic regulator support

This patch adds the TLV320AIC3x supplies and enables all of them for the
entire lifetime of the device.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320aic3x: Change bias management semantics
Jarkko Nikula [Mon, 26 Apr 2010 12:49:13 +0000]
ASoC: tlv320aic3x: Change bias management semantics

Move PLL enable from BIAS_ON state to BIAS_PREPARE to be pair with
BIAS_STANDBY where PLL is disabled. Remove also old comments about power
control.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320aic3x: Remove needless power off from aic3x_set_bias_level
Jarkko Nikula [Mon, 26 Apr 2010 12:49:12 +0000]
ASoC: tlv320aic3x: Remove needless power off from aic3x_set_bias_level

These ADC, DAC and output pin power off commands are needless in
aic3x_set_bias_level since they are not enabled in aic3x_init and they are
defined in aic3x_dapm_widgets so the ASoC DAPM will take care of them
anyway.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320aic3x: Remove unused version string
Jarkko Nikula [Mon, 26 Apr 2010 12:49:11 +0000]
ASoC: tlv320aic3x: Remove unused version string

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: UDA134X: Add UDA1345 CODEC support
Vladimir Zapolskiy [Mon, 26 Apr 2010 10:56:57 +0000]
ASoC: UDA134X: Add UDA1345 CODEC support

This patch adds support for Philips UDA1345 CODEC. The CODEC has only
volume control, de-emphasis, mute, DC filtering and power control features.

Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: Warn on low WM8994 AIFCLK
Mark Brown [Sun, 25 Apr 2010 11:20:30 +0000]
ASoC: Warn on low WM8994 AIFCLK

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: Correct inversion of speaker mixer PCM switch
Mark Brown [Fri, 23 Apr 2010 16:39:23 +0000]
ASoC: Correct inversion of speaker mixer PCM switch

Reported-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320dac33: FIFO caused delay reporting
Peter Ujfalusi [Fri, 23 Apr 2010 07:10:01 +0000]
ASoC: tlv320dac33: FIFO caused delay reporting

Delay reporting for the three implemented DAC33 FIFO modes.
DAC33 has FIFO depth status register(s), but it can not be used, since
inside of pcm_pointer we can not send I2C commands.
Timestamp based estimation need to be used. The method of calculating
the delay depends on the active FIFO mode.

Bypass mode: FIFO is bypassed, report 0 as delay

Mode1: nSample fill mode. In this mode I need to use two timestamp
ts1: taken when the interrupt has been received
ts2: taken before writing to nSample register.

Interrupts are coming when DAC33 FIFO depth goes under alarm threshold.

Phase1: when we received the alarm threshold, but our workqueue has
        not been executed (safeguard phase). Just count the played out
        samples since ts1 and subtract it from the alarm threshold
        value.
Phase2: During nSample burst (after writing to nSample register), count
        the played out samples since ts1, count the samples received
        since ts2 (in a burst). Estimate the FIFO depth using these and
        alarm threshold value.
Phase3: Draining phase (after the burst read), count the played out
        samples since ts1. Estimate the FIFO depth using the nSample
        configuration and the alarm threshold value.

Mode7: Threshold based fill mode. In this mode one timestamp is enough.
ts1: taken when the interrupt has been received

Interrupts are coming when DAC33 FIFO depth reaches upper threshold.

Phase1: Draining phase (after the burst), counting the played out
        samples since ts1, and subtract it from the upper threshold
        value.
Phase2: During burst operation. Using the pre calculated time needed to
        play out samples from the buffer during the drain period (from
        upper to lower threshold), move the time window to cover the
        estimated time from the burst start to the current time.
        Calculate the samples played out since lower threshold and also
        the samples received during the same time.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320dac33: Calculate the interface speed during bursts
Peter Ujfalusi [Fri, 23 Apr 2010 07:10:00 +0000]
ASoC: tlv320dac33: Calculate the interface speed during bursts

When the DAC33 FIFO is in use the dai interface is running in
much higher speed than the sampling frequency.
Calculate the rate based on the internal base frequency and
the bclk divider.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320dac33: Change magic numbers used in Mode7
Peter Ujfalusi [Fri, 23 Apr 2010 07:09:59 +0000]
ASoC: tlv320dac33: Change magic numbers used in Mode7

Upper and Lower threshold values are used as magic
numbers. Replace them with defines for later use.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320dac33: Skip calculations in FIFO Bypass mode
Peter Ujfalusi [Fri, 23 Apr 2010 07:09:58 +0000]
ASoC: tlv320dac33: Skip calculations in FIFO Bypass mode

There is no need for calculations for FIFO bypass mode.
Just in case set the nsample maximum limit, which
has been done in the calculation phase.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: tlv320dac33: Fix for early interrupt in FIFO Mode1
Peter Ujfalusi [Fri, 23 Apr 2010 07:09:57 +0000]
ASoC: tlv320dac33: Fix for early interrupt in FIFO Mode1

Alarm threshold interrupt is triggered right after the
playback start.
This interrupt is recieved during the first burst period,
and caused the state machine to write additional nSample
command, which has to be avoided.
To fix this issue move the DAC33 interrupt unmasking
after we configured the PREFILL register with a small
delay.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: Allow reporting of NULL jacks
Mark Brown [Mon, 29 Mar 2010 19:31:14 +0000]
ASoC: Allow reporting of NULL jacks

Follow the core jack implementation and allow reporting on the status
of NULL jacks, avoiding the need to check in detection implementations.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: ad193x: fix typo, delete redundant space
Barry Song [Wed, 21 Apr 2010 09:36:49 +0000]
ASoC: ad193x: fix typo, delete redundant space

Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: ad193x: fix wrong register setting in ad193x_set_dai_fmt
Barry Song [Wed, 21 Apr 2010 09:36:48 +0000]
ASoC: ad193x: fix wrong register setting in ad193x_set_dai_fmt

Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: Allow unspecified source when stopping WM8994 FLLs
Mark Brown [Wed, 21 Apr 2010 17:29:01 +0000]
ASoC: Allow unspecified source when stopping WM8994 FLLs

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: Tone down debugging for WM8994 class W
Mark Brown [Tue, 20 Apr 2010 04:57:08 +0000]
ASoC: Tone down debugging for WM8994 class W

It's a little verbose during path changes.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: Set full range of WM8994 FLL Fratio values
Mark Brown [Tue, 20 Apr 2010 04:36:11 +0000]
ASoC: Set full range of WM8994 FLL Fratio values

Use all the available Fratio values when configuring the WM8994 FLL, not
just 0 and 3, following more complete characterisation of the device
performance.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: Support FLL input clock selection on WM8994
Mark Brown [Tue, 20 Apr 2010 03:56:18 +0000]
ASoC: Support FLL input clock selection on WM8994

The WM8994 FLL can be clocked from one of four inputs, the two MCLKs and
the LRCLK and BCLK of the AIF associated with the FLL. Allow all four
inputs to be used rather than defaulting to MCLK1.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: da7210: Fencepost error in reg cache read
Phil Carmody [Wed, 14 Apr 2010 14:03:13 +0000]
ASoC: da7210: Fencepost error in reg cache read

An index equal to the array size may not be accessed.

Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: missing conversions to snd_soc_codec_*_drvdata()
Takashi Iwai [Tue, 20 Apr 2010 06:20:31 +0000]
ASoC: missing conversions to snd_soc_codec_*_drvdata()

Conversions to snd_soc_codec_{get|set}_drvdata() were missing in some files
in the previous commit.

Signed-off-by: Takashi Iwai <tiwai@suse.de>

9 years agoASoC: Add indirection for CODEC private data
Mark Brown [Wed, 14 Apr 2010 06:35:19 +0000]
ASoC: Add indirection for CODEC private data

One of the features of the multi CODEC work is that it embeds a struct
device in the CODEC to provide diagnostics via a sysfs class rather than
via the device tree, at which point it's much better to use the struct
device private data rather than having two places to store it. Provide
an accessor function to allow this change to be made more easily, and
update all the CODEC drivers are updated.

To ensure use of the accessor the private data structure member is
renamed, meaning that if code developed with older an older core that
still uses private_data is merged it will fail to build.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoMerge branch 'for-2.6.34' into for-2.6.35
Mark Brown [Sat, 17 Apr 2010 01:45:54 +0000]
Merge branch 'for-2.6.34' into for-2.6.35

9 years agoASoC: imx-ssi: do not call hrtimer_disable in trigger function
Sascha Hauer [Wed, 14 Apr 2010 07:17:30 +0000]
ASoC: imx-ssi: do not call hrtimer_disable in trigger function

Doing so causes a deadlock, so just signal the timer to stop
using an atomic variable.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: imx-ssi: increase minimum periods to 4
Sascha Hauer [Wed, 14 Apr 2010 07:17:31 +0000]
ASoC: imx-ssi: increase minimum periods to 4

Currently the notification of elapsed periods is not very exact.
Increase minimum periods to 4 as suggested by Liam Girdwood.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: Zipit Z2 WM8750 ASoC driver
Marek Vasut [Mon, 5 Apr 2010 04:13:38 +0000]
ASoC: Zipit Z2 WM8750 ASoC driver

This patch adds support for sound through the WM8750 codec on Zipit Z2.
Also, this patch incorporates support for detecting headset jack
insertion through the jack detection API.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: Use SNDRV_PCM_RATE_8000_96000 macro for WM8731
Bill Gatliff [Fri, 9 Apr 2010 17:08:08 +0000]
ASoC: Use SNDRV_PCM_RATE_8000_96000 macro for WM8731

Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: WM8750: Convert to new API
Marek Vasut [Thu, 8 Apr 2010 18:48:51 +0000]
ASoC: WM8750: Convert to new API

Register the WM8750 as a SPI or I2C device. This patch mostly shuffles code
around. Hugely inspired by WM8753 which was already converted.

Also, this patch fixes the Jive and Spitz machine.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: imx-ssi: Use a hrtimer in FIQ mode
Sascha Hauer [Thu, 8 Apr 2010 09:31:26 +0000]
ASoC: imx-ssi: Use a hrtimer in FIQ mode

Using a regular timer results in poll times < 1 jiffie with small
buffers, so we loaded the timer with the actual jiffie value. We can
be more accurate using a hrtimer. Also, we have to call
snd_pcm_period_elapsed after playing period_bytes and not
runtime->period_size (which is in samples and not in bytes).

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: imx-pcm-dma-mx2: restart DMA after an error
Sascha Hauer [Thu, 8 Apr 2010 09:31:25 +0000]
ASoC: imx-pcm-dma-mx2: restart DMA after an error

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: imx-ssi: honor IMX_SSI_DMA flag
Sascha Hauer [Thu, 8 Apr 2010 09:31:24 +0000]
ASoC: imx-ssi: honor IMX_SSI_DMA flag

When checking if we are DMA capable we have to check for the
IMX_SSI_DMA flag which is already set from platform_data instead
of setting it again when we want to do DMA.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@Slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: wm2000: remove unused #include <linux/version.h>
Huang Weiyi [Thu, 8 Apr 2010 11:50:08 +0000]
ASoC: wm2000: remove unused #include <linux/version.h>

Remove unused #include <linux/version.h>('s) in
  sound/soc/codecs/wm2000.c

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoMerge branch 'for-2.6.34' into for-2.6.35
Mark Brown [Mon, 5 Apr 2010 18:19:32 +0000]
Merge branch 'for-2.6.34' into for-2.6.35

Conflicts due to context changes next to the backported DMA data change:
include/sound/soc.h

9 years agoASoC: Implement interrupt based WM8994 microphone detection
Mark Brown [Mon, 29 Mar 2010 19:57:12 +0000]
ASoC: Implement interrupt based WM8994 microphone detection

Support interrupt based microphone bias detection. The WM8994 has two
microphone bias supplies, with detection supported on both. Detection
using GPIOs together with the standard GPIO based jack framework is
already supported via the platform data for the WM8994 core driver.

Note that as well as the microphone bias itself the system clock and
whichever AIF clock is supplying the system clock will need to be
enabled for detection to function.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agogpiolib: Implement gpio_to_irq for WM8994 GPIO controller
Mark Brown [Fri, 2 Apr 2010 13:51:59 +0000]
gpiolib: Implement gpio_to_irq for WM8994 GPIO controller

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agomfd: Add WM8994 interrupt controller support
Mark Brown [Fri, 26 Mar 2010 16:49:15 +0000]
mfd: Add WM8994 interrupt controller support

The WM8994 has an interrupt controller which supports interrupts for
both CODEC and GPIO portions of the chip. Support this using genirq,
while allowing for systems that do not have an interrupt hooked up.

Wrapper functions are provided for the IRQ request and free to simplify
the code in consumer drivers when handling cases where IRQs are not
set up.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

9 years agoALSA: ASoC: move dma_data from snd_soc_dai to snd_soc_pcm_stream
Daniel Mack [Mon, 22 Mar 2010 09:11:15 +0000]
ALSA: ASoC: move dma_data from snd_soc_dai to snd_soc_pcm_stream

This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.

All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.

[Note that this is a backported version for 2.6.34.
 Upstream commit is fd23b7dee]

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: Only do WM8994 bias off transition from standby
Mark Brown [Tue, 30 Mar 2010 13:29:14 +0000]
ASoC: Only do WM8994 bias off transition from standby

Otherwise we may try to power down multiple times when the using
idle bias off and the driver is removed.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: Don't use DCS_DATAPATH_BUSY for WM hubs devices
Mark Brown [Mon, 29 Mar 2010 16:18:41 +0000]
ASoC: Don't use DCS_DATAPATH_BUSY for WM hubs devices

The DCS_DATAPATH_BUSY bit used to monitor the completion of DC servo
operations has been deprecated and with some more recente revisions
may perform incorrectly, especially when only analogue bypass paths
are in use. Switch to using readback from the DC servo command
register instead, which is supported for all devices. Without this
unacceptably long timeouts may be observed in some circumstances.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: Don't do runtime wm_hubs DC servo updates if using offset correction
Mark Brown [Mon, 29 Mar 2010 15:34:42 +0000]
ASoC: Don't do runtime wm_hubs DC servo updates if using offset correction

If we need to offset correct the DC servo then don't use runtime
recalibration since that is likely to introduce further offsets
which will be evident on powerdown.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: Support second DC servo readback method for wm_hubs
Mark Brown [Mon, 29 Mar 2010 16:09:45 +0000]
ASoC: Support second DC servo readback method for wm_hubs

More recent Wolfson hubs devices add the ability to read back the DC
servo calibration information from the register used to write offsets,
and later still ones remove the old readback registers. Add support
for the new scheme, and use it for WM8994 device revisions that
support it.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: Avoid wraparound in wm_hubs DC servo correction
Mark Brown [Mon, 29 Mar 2010 14:24:40 +0000]
ASoC: Avoid wraparound in wm_hubs DC servo correction

If the correction wraps around then a substantial offset would be
introduced.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: OMAP: Fix capture pointer handling for OMAP1510 to work correctly with recent...
Janusz Krzysztofik [Sun, 28 Mar 2010 20:29:29 +0000]
ASoC: OMAP: Fix capture pointer handling for OMAP1510 to work correctly with recent ALSA PCM code

With recent (2.6.34) chnages in PCM handling, capture stopped working on my
OMAP1510 based Amstrad Delta videophone.

Using 2.6.34-rc2, I was able to correct the problem in 3 different ways:

1. reverting commit 7b3a177b0d4f92b3431b8dca777313a07533a710,
2. enabling additional jiffies check with
echo 4 >/proc/asound/card0/pcm0c0/xrun_debug
3. applying the patch below.

Since I wasn't able to reproduce the problem on my i686 PC, I guess the
problem is probably machine specific.

The patch reuses the method for software emulation of missing hardware
pointer, already implemented for playback on OMAP1510. It's possible that
event if a hardware pointer is available for capture on this machine, its
behaviour may be not compatible with what upper layer expects.

If you think the problem may be more general and should be solved differently,
on a higher level, I can try to work more on it if you give me a hint.

If the patch gets accepted, I suggest it goes as a fix in the current release
cycle.

Created and tested against linux-2.6.34-rc2.

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agomfd: update gfp/slab.h includes
Tejun Heo [Mon, 29 Mar 2010 17:52:40 +0000]
mfd: update gfp/slab.h includes

Implicit slab.h inclusion via percpu.h is about to go away.  Make sure
gfp.h or slab.h is included as necessary.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoMerge branch 'for-2.6.34' into for-2.6.35
Mark Brown [Mon, 29 Mar 2010 20:03:20 +0000]
Merge branch 'for-2.6.34' into for-2.6.35

9 years agoASoC: ad193x: move codec register/unregister to bus probe/remove
Barry Song [Mon, 29 Mar 2010 03:16:00 +0000]
ASoC: ad193x: move codec register/unregister to bus probe/remove

The way i've factored out the bus probe and removal functions so
that there's no code in the individual I2C and SPI functions means
that the register() and unregister() functions could just be squashed
into the bus_probe() and bus_remove() functions.

Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: Fix passing platform_data to ac97 bus users and fix a leak
Graham Gower [Thu, 25 Mar 2010 00:22:12 +0000]
ASoC: Fix passing platform_data to ac97 bus users and fix a leak

[The issue is an attempt to write the pdata without the AC97 device
allocated when using ac97.c - also added a comment in soc-core.c for the
special case for ac97. -- broonie]

Signed-off-by: Graham Gower <graham.gower@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoMerge branch 'topic/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai...
Mark Brown [Mon, 29 Mar 2010 20:00:04 +0000]
Merge branch 'topic/asoc' of git://git./linux/kernel/git/tiwai/sound-2.6 into for-2.6.35

9 years agoASoC: update gfp/slab.h includes
Tejun Heo [Mon, 29 Mar 2010 17:52:29 +0000]
ASoC: update gfp/slab.h includes

Implicit slab.h inclusion via percpu.h is about to go away.  Make sure
gfp.h or slab.h is included as necessary.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

9 years agoASoC: Fix file permission of soc/codecs/twl6040.c
Takashi Iwai [Mon, 29 Mar 2010 07:31:57 +0000]
ASoC: Fix file permission of soc/codecs/twl6040.c

Signed-off-by: Takashi Iwai <tiwai@suse.de>

9 years agoASoC: TWL6040: use of kzalloc/kfree requires the include of slab.h
Stephen Rothwell [Mon, 29 Mar 2010 06:55:51 +0000]
ASoC: TWL6040: use of kzalloc/kfree requires the include of slab.h

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

9 years agoASoC: update for removeal of slab.h from percpu.h
Stephen Rothwell [Mon, 29 Mar 2010 04:32:18 +0000]
ASoC: update for removeal of slab.h from percpu.h

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

9 years agoASoC: fsi: Add FSI2 device support
Kuninori Morimoto [Thu, 25 Mar 2010 10:15:53 +0000]
ASoC: fsi: Add FSI2 device support

ARM-SHMOBILE series have FIFO-buffered serial interface 2 (FSI2)
device which is advanced version of FSI.
This patch add simple support for it.

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: fsi: Add FIFO size calculate
Kuninori Morimoto [Thu, 25 Mar 2010 10:15:51 +0000]
ASoC: fsi: Add FIFO size calculate

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: wm8994: playback => capture
Dan Carpenter [Wed, 24 Mar 2010 11:58:34 +0000]
ASoC: wm8994: playback => capture

Sparse caught that initialize "playback" two times instead of
initializing "capture".

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: fsi: IRQ related process had be united
Kuninori Morimoto [Tue, 23 Mar 2010 02:47:54 +0000]
ASoC: fsi: IRQ related process had be united

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: fsi: ensures process inside master lock
Kuninori Morimoto [Wed, 24 Mar 2010 06:27:24 +0000]
ASoC: fsi: ensures process inside master lock

Bit operation for fsi_master should be done inside master lock.
But soft-reset/interrupt operation were outside of it.
This patch modify this problem.
It still allow to INT_ST outside-operation on fsi_interrupt,
but it is not problem.
Because this register doesn't need the bit operation.

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: ak4642: Add enhanced sampling rate
Kuninori Morimoto [Tue, 23 Mar 2010 07:27:38 +0000]
ASoC: ak4642: Add enhanced sampling rate

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: ak4642: Add set_fmt function for snd_soc_dai_ops
Kuninori Morimoto [Mon, 15 Mar 2010 09:10:50 +0000]
ASoC: ak4642: Add set_fmt function for snd_soc_dai_ops

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: ak4642: Add pll select support
Kuninori Morimoto [Tue, 23 Mar 2010 07:27:28 +0000]
ASoC: ak4642: Add pll select support

Current ak4642 was not able to select pll.
This patch add support it.
It still expect PLL base input pin is MCKI.
see Table 5 "setting of PLL Mode" of datasheet

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

9 years agoASoC: Implement WM8994 DAI tristate support
Mark Brown [Mon, 22 Mar 2010 22:05:10 +0000]
ASoC: Implement WM8994 DAI tristate support

This also adds the first DAI operation for AIF3 so fill out the ID and
the ops for that too.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoMerge branch 'for-2.6.34' into for-2.6.35
Mark Brown [Mon, 22 Mar 2010 17:23:46 +0000]
Merge branch 'for-2.6.34' into for-2.6.35

9 years agoASoC: Allow WM8903 mic detect disable and don't force bias on
Mark Brown [Mon, 22 Mar 2010 16:37:01 +0000]
ASoC: Allow WM8903 mic detect disable and don't force bias on

Don't force enable the microphone bias on WM8903 when doing jack
detection, and don't force enable microphone bias. This allows
platforms to only enable microphone detection when a jack has been
inserted.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

9 years agoASoC: Allow disabling of WM835x jack detection
Mark Brown [Mon, 22 Mar 2010 15:30:30 +0000]
ASoC: Allow disabling of WM835x jack detection

If no report is specified then disable detection. Note that we don't
disable the slow clock, though the power consumption from it should
be negligable. That should be reference counted, ideally through DAPM.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>