10 years agoBlackfin Serial Driver: disable dma rx interrupt only rather than all irqs
Sonic Zhang [Thu, 11 Jun 2009 12:51:33 +0000]
Blackfin Serial Driver: disable dma rx interrupt only rather than all irqs

The UART RX handling code isn't exactly speeding, so don't go disabling
all interrupts when processing the buffer.  Just disable the relevant DMA
interrupt.  This greatly improves latency of the system when utilizing the
UART.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoBlackfin Serial Driver: handle anomaly 05000231
Sonic Zhang [Thu, 11 Jun 2009 12:50:20 +0000]
Blackfin Serial Driver: handle anomaly 05000231

05000231 - UART STB Bit Incorrectly Affects Receiver Setting
For processors affected by this, we cannot safely allow CSTOPB to be set
as the UART will then be unable to properly clock in bytes.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoBlackfin Serial Driver: annotate anomalies 05000215 and 05000099
Sonic Zhang [Thu, 11 Jun 2009 12:45:07 +0000]
Blackfin Serial Driver: annotate anomalies 05000215 and 05000099

Add some comments for how these anomalies are addressed:

05000215 - UART TX Interrupt Masked Erroneously
We always clear ETBEI within last UART TX interrupt to end
a string.  It is always set when starting a new tx transfer.

05000099 - UART Line Status Register (UART_LSR) Bits Are Not Updated at
the Same Time
This anomaly affects driver only in POLL code where multi bits of
UART_LSR are checked. It doesn't affect current bfin_5xx.c driver.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoBlackfin Serial Driver: handle irregular DMA register status in auto start mode
Sonic Zhang [Thu, 11 Jun 2009 12:42:57 +0000]
Blackfin Serial Driver: handle irregular DMA register status in auto start mode

This bug is caused by irregular behavior of DMA register CURR_X_COUNT
and CURR_Y_COUNT when an auto restart uart rx DMA run to last byte in
DMA buffer, trigger the interrupt and stay at this possiton. The status
of current x and y is 0:7 instead of 512:8 or 0:8. The driver doesn't
take care of this case when calculating the position.

URL: http://blackfin.uclinux.org/gf/tracker/5063
Reported-by: Tomasz Motylewski <t.motylewski@bfad.de>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoBlackfin Serial Driver: fix missing new lines when under load
Graf Yang [Thu, 11 Jun 2009 12:42:17 +0000]
Blackfin Serial Driver: fix missing new lines when under load

Add a SSYNC() into bfin_serial_dma_tx_chars() to ensure DMA registers are
written with new data otherwise we might miss a byte or two when the
system is under load.  PIO mode is OK though.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoBlackfin Serial Driver: fix baudrate for early_printk
Robin Getz [Thu, 11 Jun 2009 12:38:57 +0000]
Blackfin Serial Driver: fix baudrate for early_printk

Since we already setup the early console UART in
arch/blackfin/kernel/early_printk.c, and common functions which are
enabled from the .setup will override the proper settings later, don't
fill in these structures.  Otherwise we get mangled baudrate settings when
using early_printk.

Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoBlackfin Serial Driver: fix error while transferring large files
Sonic Zhang [Thu, 11 Jun 2009 12:38:16 +0000]
Blackfin Serial Driver: fix error while transferring large files

Ignore receiving data if new position is in the same line of current
buffer tail and is small.  This should decrease overruns.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoBlackfin SPORT UART: rewrite inline assembly
Mike Frysinger [Thu, 11 Jun 2009 12:37:11 +0000]
Blackfin SPORT UART: rewrite inline assembly

Hopefuly the new version is easier to read, but in the process it declares
proper clobber lists and better constraints so that GCC can do a better
job at allocating free registers.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoBlackfin SPORT UART: fix data misses while using transmit frame sync
Michael Hennerich [Thu, 11 Jun 2009 12:23:42 +0000]
Blackfin SPORT UART: fix data misses while using transmit frame sync

SPORT transmit frame sync (TFS) isn't used as an electrical signal during
normal SPORT UART emulation.  However, it is useful in EIA RS-485
emulation as RS-485 Transceiver Driver Enable DE strobe.

This patch configures:
TFS to be active high in order to drive an DE strobe of
an eventually connected RS-485 Transceiver.

Late frame sync mode (LATFS) gating the entire TX shift cycle.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoBlackfin SPORT UART: fix typo in sport_set_termios prototype
Mike Frysinger [Thu, 11 Jun 2009 12:23:02 +0000]
Blackfin SPORT UART: fix typo in sport_set_termios prototype

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoserial: add support for the TI AR7 internal UART
Florian Fainelli [Thu, 11 Jun 2009 12:21:24 +0000]
serial: add support for the TI AR7 internal UART

This patch adds support for the TI AR7 internal UART.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoicom: fix compile errors when defining ICOM_TRACE
Breno Leitao [Thu, 11 Jun 2009 12:20:09 +0000]
icom: fix compile errors when defining ICOM_TRACE

As it is, defining ICOM_TRACE produces some compile errors, as
"parameter name omitted" and "redefinition of ‘trace’"

This patch removes the wrong trace definition.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoparport_pc: clean up the modified while loops using for
Alan Cox [Thu, 11 Jun 2009 12:08:10 +0000]
parport_pc: clean up the modified while loops using for

And tidy up a few bits coding style detectors missed

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoparport_pc: Coding style
Alan Cox [Thu, 11 Jun 2009 12:07:29 +0000]
parport_pc: Coding style

Michael's patch fixed some of the coding style so the style is now
inconsistent. Sort the rest out

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoparport_pc: Fix subscription bugs
Michael Buesch [Thu, 11 Jun 2009 12:06:31 +0000]
parport_pc: Fix subscription bugs

This patch fixes array subscription bugs in the parport_pc driver.

drivers/parport/parport_pc.c: In function ‘parport_irq_probe’:
drivers/parport/parport_pc.c:1589: warning: array subscript is above array bounds
drivers/parport/parport_pc.c: In function ‘parport_pc_probe_port’:
drivers/parport/parport_pc.c:1579: warning: array subscript is above array bounds

The patch also fixes a few other array bugs, which the compiler was
unable to find. Coding style violations are also fixed.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: simplify buffer allocator cleanups
Alan Cox [Thu, 11 Jun 2009 12:05:49 +0000]
tty: simplify buffer allocator cleanups

Having cleaned up the allocators we might as well remove the inline helpers
for some of it

Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: remove buffer special casing
Alan Cox [Thu, 11 Jun 2009 12:04:27 +0000]
tty: remove buffer special casing

Long long ago a 4K kmalloc allocated two pages so the tty layer used the
page allocator, except on some machines where the page size was huge. This was
removed from the core tty layer with the tty buffer re-implementation but not
from tty_audit or the n_tty ldisc.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoicom: fixing a if clause spaghetti
Breno Leitao [Thu, 11 Jun 2009 12:02:59 +0000]
icom: fixing a if clause spaghetti

adapter->version can only be ADAPTER_V2 or ADAPTER_V1. So,
that OR operand in the "if" clause is non-sense and can be removed.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agojsm: correctly support multiple 4/8-port boards
Alexander Y. Fomichev [Thu, 11 Jun 2009 11:56:00 +0000]
jsm: correctly support multiple 4/8-port boards

If there are more then one 4/8-port board jsm_uart_port_init
allocate a line numbers of the second and further boards
from range of previous one.

This patch fixed the problem.

Signed-off-by: Alexander Y. Fomichev <git.user@gmail.com>

[printks fixed to add jsm: ]

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: iuu_phoenix: update version number.
Olivier Bornet [Thu, 11 Jun 2009 11:55:01 +0000]
tty: iuu_phoenix: update version number.

Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: iuu_phoenix: set termios.
Olivier Bornet [Thu, 11 Jun 2009 11:54:20 +0000]
tty: iuu_phoenix: set termios.

set_termios can now be used for setting the parity and the stopbits. This is
needed to use with cards which use a different parity then the parity used at
start (even).

If the iuu_uart_baud function return an error, we will return the old_termios
instead of the new one.

Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>

This was then revamped to use the various helpers, not copy non-hardware
bits any to add mark/space parity and csize reporting

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: iuu_phoenix: Fix stopbit when uart goes on.
Olivier Bornet [Thu, 11 Jun 2009 11:53:24 +0000]
tty: iuu_phoenix: Fix stopbit when uart goes on.

Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: iuu_phoenix: fix locking.
Olivier Bornet [Thu, 11 Jun 2009 11:52:26 +0000]
tty: iuu_phoenix: fix locking.

Bring in the relevant bits of the 0.9 vendor driver.

Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: bring ldisc into CodingStyle
Alan Cox [Thu, 11 Jun 2009 11:51:41 +0000]
tty: bring ldisc into CodingStyle

Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: Move ldisc_flush
Alan Cox [Thu, 11 Jun 2009 11:50:58 +0000]
tty: Move ldisc_flush

We have a tty_ldisc file now so put tty_ldisc_flush in the right place

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: rewrite the ldisc locking
Alan Cox [Thu, 11 Jun 2009 11:50:12 +0000]
tty: rewrite the ldisc locking

There are several pretty much unfixable races in the old ldisc code, especially
with respect to pty behaviour and also to hangup. It's easier to rewrite the
code than simply try and patch it up.

This patch
- splits the ldisc from the tty (so we will be able to refcount it more cleanly
  later)
- introduces a mutex lock for ldisc changing on an active device
- fixes the complete mess that hangup caused
- implements hopefully correct setldisc/close/hangup locking

There are still some problems around pty pairs that have always been there but
at least it is now possible to understand the code and fix further problems.

This fixes the following known bugs
- hang up can leak ldisc references
- hang up may not call open/close on ldisc in a matched way
- pty/tty pairs can deadlock during an ldisc change
- reading the ldisc proc files can cause every ldisc to be loaded

and probably a few other of the mysterious ldisc race reports.

I'm sure it also adds the odd new one.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: Extract various bits of ldisc code
Alan Cox [Thu, 11 Jun 2009 11:48:02 +0000]
tty: Extract various bits of ldisc code

Before trying to tackle the ldisc bugs the code needs to be a good deal
more readable, so do the simple extractions of routines first.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: Fix oops when scanning the polling list for kgdb
Alan Cox [Thu, 11 Jun 2009 11:46:41 +0000]
tty: Fix oops when scanning the polling list for kgdb

Costantino Leandro found a bug in tty_find_polling_driver and provided a
patch that fixed the crash but not the underlying bug. This fixes the
underlying bug where the list walk corrupts the values it is using on a
match but then reuses them if the open fails.

Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agopty: Fix a comment
Alan Cox [Thu, 11 Jun 2009 11:45:53 +0000]
pty: Fix a comment

We fixed the globals, so now fix the comment

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoserial: update maintainers file
Alan Cox [Thu, 11 Jun 2009 11:45:08 +0000]
serial: update maintainers file

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: throttling race fix
Alan Cox [Thu, 11 Jun 2009 11:44:17 +0000]
tty: throttling race fix

The tty throttling code can race due to the lock drops. It takes very high
loads but this has been observed and verified by Rob Duncan.

The basic problem is that on an SMP box we can go

CPU #1 CPU #2
need to throttle ?
suppose we should buffer space cleared
are we throttled
yes ? - unthrottle
call throttle method

This changeet take the termios lock to protect against this. The termios
lock isn't the initial obvious candidate but many implementations of throttle
methods already need to poke around their own termios structures (and nobody
really locks them against a racing change of flow control).

This does mean that anyone who is setting tty->low_latency = 1 and then
calling tty_flip_buffer_push from their unthrottle method is going to end up
collapsing in a pile of locks. However we've removed all the known bogus
users of low_latency = 1 and such use isn't safe anyway for other reasons so
catching it would be an improvement.

Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agox86: fix ktermios-termio conversion
Arnd Bergmann [Thu, 11 Jun 2009 11:42:49 +0000]
x86: fix ktermios-termio conversion

The legacy TCSETA{,W,F} ioctls failed to set the termio->c_line field
on x86. This adds a missing get_user.

The same ioctls also fail to report faulting user pointers, which
we keep ignoring.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years ago8250_pci: add the OXCB950 chip to the 8250 PCI driver.
Andre Przywara [Thu, 11 Jun 2009 11:41:57 +0000]
8250_pci: add the OXCB950 chip to the 8250 PCI driver.

This adds support for the following serial controller chip:
Oxford Semiconductor OXCB950 for PCI Cardbus interface
http://www.transdimension.com/products/serial/OXCB950.html

on this card:
ExSys EX-1370 1 port high-speed serial card for ExpressCard/34 slot

Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoepca: fix test_bit parameters
Jiri Slaby [Thu, 11 Jun 2009 11:41:05 +0000]
epca: fix test_bit parameters

Switch from ASYNC_* to ASYNCB_*, because test_bit expects
bit number, not mask.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agorocket: fix test_bit parameters
Jiri Slaby [Thu, 11 Jun 2009 11:40:17 +0000]
rocket: fix test_bit parameters

Switch from ASYNC_* to ASYNCB_*, because {test,set}_bit expect
bit number, not mask.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoserial: refactor ASYNC_ flags
Jiri Slaby [Thu, 11 Jun 2009 11:39:12 +0000]
serial: refactor ASYNC_ flags

Define ASYNCB_* flags which are bit numbers of the ASYNC_* flags.
This is useful for {test,set,clear}_bit.

Also convert each ASYNC_% to be (1 << ASYNCB_%) and define masks
with the macros, not constants.

Tested with:
#include "PATH_TO_KERNEL/include/linux/serial.h"
static struct {
        unsigned int new, old;
} as[] = {
        { ASYNC_HUP_NOTIFY, 0x0001 },
        { ASYNC_FOURPORT, 0x0002 },
...
{ ASYNC_BOOT_ONLYMCA, 0x00400000 },
        { ASYNC_INTERNAL_FLAGS, 0xFFC00000 }
};
...
        for (a = 0; a < ARRAY_SIZE(as); a++)
                if (as[a].old != as[a].new)
                        printf("%.8x != %.8x\n", as[a].old, as[a].new);

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: Clean up the ACM driver to CodingStyle
Alan Cox [Thu, 11 Jun 2009 11:37:06 +0000]
tty: Clean up the ACM driver to CodingStyle

Or at least most of it. There are further clean ups possible and there are
are also thing checkpatch moans about that would be silly to "fix".

Also note some FIXME points found as the cleanup was done.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: cdc_acm add krefs
Alan Cox [Thu, 11 Jun 2009 11:36:09 +0000]
tty: cdc_acm add krefs

Now we have a port structure begin using the fields and kref counts

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: cyclades, remove unused variables
Jiri Slaby [Thu, 11 Jun 2009 11:35:21 +0000]
tty: cyclades, remove unused variables

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: cyclades, fix nports handling
Jiri Slaby [Thu, 11 Jun 2009 11:34:27 +0000]
tty: cyclades, fix nports handling

Set up ports right after FW load so that we won't allocate maximal
(64) ports when we use few.

Also remove reading of nports in irq context, since we know it from
initialisation now.

This also fixes a tty ports unregistration on some fail paths and for
Ze which registered 64 and unregistered real port count.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: cyclades, remove typedefs
Jiri Slaby [Thu, 11 Jun 2009 11:33:40 +0000]
tty: cyclades, remove typedefs

They are unused anyway.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: cyclades, convert macros to inlines
Jiri Slaby [Thu, 11 Jun 2009 11:31:06 +0000]
tty: cyclades, convert macros to inlines

Remove ugly macros and add inlines instead of them. This improves
readability and type checking a much.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: cyclades, cache HW version
Jiri Slaby [Thu, 11 Jun 2009 11:30:10 +0000]
tty: cyclades, cache HW version

Store HW version locally to not read it all the time in interrupts
and alike.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: cyclades, plx9060 casts cleanup
Jiri Slaby [Thu, 11 Jun 2009 11:29:27 +0000]
tty: cyclades, plx9060 casts cleanup

Remove ugly all-over-the-code casts of ctl_addr to 9060 space.
Add an union to the cyclades_card structure, which contains
a pointer to both 9050 and 9060 spaces.

The 9050 space layout is unknown, so let it still as a void
__iomem pointer.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: synclink_gt add receive pio mode
Paul Fulghum [Thu, 11 Jun 2009 11:28:37 +0000]
tty: synclink_gt add receive pio mode

Add receive programmed IO mode to reduce receive latency
when using low data rates. The receive FIFO trigger
level of 128 bytes used in DMA mode creates excessive latency
when operating at low data rates. PIO mode is selected when user
application requests data in blocks of less than 128 bytes.

Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: Update cdc_acm
Alan Cox [Thu, 11 Jun 2009 11:27:50 +0000]
tty: Update cdc_acm

The CDC ACM driver uses the tty layer correctly so needs conversion. Start by
adding and initializing the port structures.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: Bring the usb tty port structure into more use
Alan Cox [Thu, 11 Jun 2009 11:26:29 +0000]
tty: Bring the usb tty port structure into more use

This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.

Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: Implement a drain delay in the tty port
Alan Cox [Thu, 11 Jun 2009 11:25:25 +0000]
tty: Implement a drain delay in the tty port

We need this for devices that cannot flush and wait, but which do not order
data and modem events. Without it we will hang up before all the data
clears the hardware. Needed for the USB changes.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: Add carrier processing on close to the tty_port core
Alan Cox [Thu, 11 Jun 2009 11:24:17 +0000]
tty: Add carrier processing on close to the tty_port core

Some drivers implement this internally, others miss it out. Push the
behaviour into the core code as that way everyone will do it consistently.

Update the dtr rts method to raise or lower depending upon flags. Having a
single method in this style fits most of the implementations more cleanly than
two funtions.

We need this in place before we tackle the USB side

Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: cyclades, remove spurious check in ISR
Jiri Slaby [Thu, 11 Jun 2009 11:22:27 +0000]
tty: cyclades, remove spurious check in ISR

No need to check if dev_id is NULL, it never is.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty: cyclades, don't kill FW
Jiri Slaby [Thu, 11 Jun 2009 11:21:30 +0000]
tty: cyclades, don't kill FW

Don't reset the PLX chip after FW load, which effectively kills
the FW, so that user had to boot manually.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agotty:cyclades, load firmware even on Ze
Jiri Slaby [Thu, 11 Jun 2009 11:20:38 +0000]
tty:cyclades, load firmware even on Ze

Ze needs firmware to be loaded as well as Zo. Move cyz_load_fw one
level upper to achieve that.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoLinux 2.6.30
Linus Torvalds [Wed, 10 Jun 2009 03:05:27 +0000]
Linux 2.6.30

10 years agochar: mxser, fix ISA board lookup
Peter Botha [Wed, 10 Jun 2009 00:16:32 +0000]
char: mxser, fix ISA board lookup

There's a bug in the mxser kernel module that still appears in the
2.6.29.4 kernel.

mxser_get_ISA_conf takes a ioaddress as its first argument, by passing the
not of the ioaddr, you're effectively passing 0 which means it won't be
able to talk to an ISA card.  I have tested this, and removing the !
fixes the problem.

Cc: "Peter Botha" <peterb@goldcircle.co.za>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agojbd: fix race in buffer processing in commit code
Jan Kara [Tue, 9 Jun 2009 23:26:26 +0000]
jbd: fix race in buffer processing in commit code

In commit code, we scan buffers attached to a transaction.  During this
scan, we sometimes have to drop j_list_lock and then we recheck whether
the journal buffer head didn't get freed by journal_try_to_free_buffers().
 But checking for buffer_jbd(bh) isn't enough because a new journal head
could get attached to our buffer head.  So add a check whether the journal
head remained the same and whether it's still at the same transaction and
list.

This is a nasty bug and can cause problems like memory corruption (use after
free) or trigger various assertions in JBD code (observed).

Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoautofs4: remove hashed check in validate_wait()
Ian Kent [Tue, 9 Jun 2009 23:26:24 +0000]
autofs4: remove hashed check in validate_wait()

The recent ->lookup() deadlock correction required the directory inode
mutex to be dropped while waiting for expire completion.  We were
concerned about side effects from this change and one has been identified.

I saw several error messages.

They cause autofs to become quite confused and don't really point to the
actual problem.

Things like:

handle_packet_missing_direct:1376: can't find map entry for (43,1827932)

which is usually totally fatal (although in this case it wouldn't be
except that I treat is as such because it normally is).

do_mount_direct: direct trigger not valid or already mounted
/test/nested/g3c/s1/ss1

which is recoverable, however if this problem is at play it can cause
autofs to become quite confused as to the dependencies in the mount tree
because mount triggers end up mounted multiple times.  It's hard to
accurately check for this over mounting case and automount shouldn't need
to if the kernel module is doing its job.

There was one other message, similar in consequence of this last one but I
can't locate a log example just now.

When checking if a mount has already completed prior to adding a new mount
request to the wait queue we check if the dentry is hashed and, if so, if
it is a mount point.  But, if a mount successfully completed while we
slept on the wait queue mutex the dentry must exist for the mount to have
completed so the test is not really needed.

Mounts can also be done on top of a global root dentry, so for the above
case, where a mount request completes and the wait queue entry has already
been removed, the hashed test returning false can cause an incorrect
callback to the daemon.  Also, d_mountpoint() is not sufficient to check
if a mount has completed for the multi-mount case when we don't have a
real mount at the base of the tree.

Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoshm: fix unused warnings on nommu
Mike Frysinger [Tue, 9 Jun 2009 23:26:23 +0000]
shm: fix unused warnings on nommu

The massive nommu update (8feae131) resulted in these warnings:
ipc/shm.c: In function `sys_shmdt':
ipc/shm.c:974: warning: unused variable `size'
ipc/shm.c:972: warning: unused variable `next'

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus
Linus Torvalds [Tue, 9 Jun 2009 15:48:32 +0000]
Merge git://git./linux/kernel/git/rusty/linux-2.6-for-linus

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  kvm: fix kvm reboot crash when MAXSMP is used
  cpumask: alloc zeroed cpumask for static cpumask_var_ts
  cpumask: introduce zalloc_cpumask_var

10 years agoMerge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
Linus Torvalds [Tue, 9 Jun 2009 15:47:43 +0000]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  bsg: setting rq->bio to NULL

10 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Tue, 9 Jun 2009 15:47:27 +0000]
Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  cls_cgroup: Fix oops when user send improperly 'tc filter add' request
  r8169: fix crash when large packets are received

10 years agoMerge branch 'for-linus' of git://neil.brown.name/md
Linus Torvalds [Tue, 9 Jun 2009 15:41:22 +0000]
Merge branch 'for-linus' of git://neil.brown.name/md

* 'for-linus' of git://neil.brown.name/md:
  md/raid5: fix bug in reshape code when chunk_size decreases.
  md/raid5 - avoid deadlocks in get_active_stripe during reshape
  md/raid5: use conf->raid_disks in preference to mddev->raid_disk

10 years agobsg: setting rq->bio to NULL
FUJITA Tomonori [Tue, 9 Jun 2009 13:17:37 +0000]
bsg: setting rq->bio to NULL

Due to commit 1cd96c242a829d52f7a5ae98f554ca9775429685 ("block: WARN
in __blk_put_request() for potential bio leak"), BSG SMP requests get
the false warnings:

WARNING: at block/blk-core.c:1068 __blk_put_request+0x52/0xc0()

This sets rq->bio to NULL to avoid that false warnings.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

10 years agokvm: fix kvm reboot crash when MAXSMP is used
Avi Kivity [Sat, 6 Jun 2009 21:52:35 +0000]
kvm: fix kvm reboot crash when MAXSMP is used

one system was found there is crash during reboot then kvm/MAXSMP
Sending all processes the KILL signal...                              done
Please stand by while rebooting the system...
[ 1721.856538] md: stopping all md devices.
[ 1722.852139] kvm: exiting hardware virtualization
[ 1722.854601] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 1722.872219] IP: [<ffffffff8102c6b6>] hardware_disable+0x4c/0xb4
[ 1722.877955] PGD 0
[ 1722.880042] Oops: 0000 [#1] SMP
[ 1722.892548] last sysfs file: /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/host0/target0:2:0/0:2:0:0/vendor
[ 1722.900977] CPU 9
[ 1722.912606] Modules linked in:
[ 1722.914226] Pid: 0, comm: swapper Not tainted 2.6.30-rc7-tip-01843-g2305324-dirty #299 ...
[ 1722.932589] RIP: 0010:[<ffffffff8102c6b6>]  [<ffffffff8102c6b6>] hardware_disable+0x4c/0xb4
[ 1722.942709] RSP: 0018:ffffc900010b6ed8  EFLAGS: 00010046
[ 1722.956121] RAX: 0000000000000000 RBX: ffffc9000e253140 RCX: 0000000000000009
[ 1722.972202] RDX: 000000000000b020 RSI: ffffc900010c3220 RDI: ffffffffffffd790
[ 1722.977399] RBP: ffffc900010b6f08 R08: 0000000000000000 R09: 0000000000000000
[ 1722.995149] R10: 00000000000004b8 R11: 966912b6c78fddbd R12: 0000000000000009
[ 1723.011551] R13: 000000000000b020 R14: 0000000000000009 R15: 0000000000000000
[ 1723.019898] FS:  0000000000000000(0000) GS:ffffc900010b3000(0000) knlGS:0000000000000000
[ 1723.034389] CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
[ 1723.041164] CR2: 0000000000000000 CR3: 0000000001001000 CR4: 00000000000006e0
[ 1723.056192] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1723.072546] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 1723.080562] Process swapper (pid: 0, threadinfo ffff88107e464000, task ffff88047e5a2550)
[ 1723.096144] Stack:
[ 1723.099071]  0000000000000046 ffffc9000e253168 966912b6c78fddbd ffffc9000e253140
[ 1723.115471]  ffff880c7d4304d0 ffffc9000e253168 ffffc900010b6f28 ffffffff81011022
[ 1723.132428]  ffffc900010b6f48 966912b6c78fddbd ffffc900010b6f48 ffffffff8100b83b
[ 1723.141973] Call Trace:
[ 1723.142981]  <IRQ> <0> [<ffffffff81011022>] kvm_arch_hardware_disable+0x26/0x3c
[ 1723.158153]  [<ffffffff8100b83b>] hardware_disable+0x3f/0x55
[ 1723.172168]  [<ffffffff810b95f6>] generic_smp_call_function_interrupt+0x76/0x13c
[ 1723.178836]  [<ffffffff8104cbea>] smp_call_function_interrupt+0x3a/0x5e
[ 1723.194689]  [<ffffffff81035bf3>] call_function_interrupt+0x13/0x20
[ 1723.199750]  <EOI> <0> [<ffffffff814ad3b4>] ? acpi_idle_enter_c1+0xd3/0xf4
[ 1723.217508]  [<ffffffff814ad3ae>] ? acpi_idle_enter_c1+0xcd/0xf4
[ 1723.232172]  [<ffffffff814ad4bc>] ? acpi_idle_enter_bm+0xe7/0x2ce
[ 1723.235141]  [<ffffffff81a8d93f>] ? __atomic_notifier_call_chain+0x0/0xac
[ 1723.253381]  [<ffffffff818c3dff>] ? menu_select+0x58/0xd2
[ 1723.258179]  [<ffffffff818c2c9d>] ? cpuidle_idle_call+0xa4/0xf3
[ 1723.272828]  [<ffffffff81034085>] ? cpu_idle+0xb8/0x101
[ 1723.277085]  [<ffffffff81a80163>] ? start_secondary+0x1bc/0x1d7
[ 1723.293708] Code: b0 00 00 65 48 8b 04 25 28 00 00 00 48 89 45 e0 31 c0 48 8b 04 cd 30 ee 27 82 49 89 cc 49 89 d5 48 8b 04 10 48 8d b8 90 d7 ff ff <48> 8b 87 70 28 00 00 48 8d 98 90 d7 ff ff eb 16 e8 e9 fe ff ff
[ 1723.335524] RIP  [<ffffffff8102c6b6>] hardware_disable+0x4c/0xb4
[ 1723.342076]  RSP <ffffc900010b6ed8>
[ 1723.352021] CR2: 0000000000000000
[ 1723.354348] ---[ end trace e2aec53dae150aa1 ]---

it turns out that we need clear cpus_hardware_enabled in that case.

Reported-and-tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

10 years agocpumask: alloc zeroed cpumask for static cpumask_var_ts
Yinghai Lu [Sat, 6 Jun 2009 21:51:36 +0000]
cpumask: alloc zeroed cpumask for static cpumask_var_ts

These are defined as static cpumask_var_t so if MAXSMP is not used,
they are cleared already.  Avoid surprises when MAXSMP is enabled.

Signed-off-by: Yinghai Lu <yinghai.lu@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

10 years agocpumask: introduce zalloc_cpumask_var
Yinghai Lu [Sat, 6 Jun 2009 21:50:36 +0000]
cpumask: introduce zalloc_cpumask_var

So can get cpumask_var with cpumask_clear

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

10 years agocls_cgroup: Fix oops when user send improperly 'tc filter add' request
Minoru Usui [Tue, 9 Jun 2009 11:03:09 +0000]
cls_cgroup: Fix oops when user send improperly 'tc filter add' request

I found a bug in cls_cgroup_change() in cls_cgroup.c.
cls_cgroup_change() expected tca[TCA_OPTIONS] was set from user space properly,
but tc in iproute2-2.6.29-1 (which I used) didn't set it.

In the current source code of tc in git, it set tca[TCA_OPTIONS].

  git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/iproute2.git

If we always use a newest iproute2 in git when we use cls_cgroup,
we don't face this oops probably.
But I think, kernel shouldn't panic regardless of use program's behaviour.

Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agor8169: fix crash when large packets are received
Eric Dumazet [Tue, 9 Jun 2009 11:01:02 +0000]
r8169: fix crash when large packets are received

Michael Tokarev reported receiving a large packet could crash
a machine with RTL8169 NIC.
( original thread at http://lkml.org/lkml/2009/6/8/192 )

Problem is this driver tells that NIC frames up to 16383 bytes
can be received but provides skb to rx ring allocated with
smaller sizes (1536 bytes in case standard 1500 bytes MTU is used)

When a frame larger than what was allocated by driver is received,
dma transfert can occurs past the end of buffer and corrupt
kernel memory.

Fix is to tell to NIC what is the maximum size a frame can be.

This bug is very old, (before git introduction, linux-2.6.10), and
should be backported to stable versions.

Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

10 years agomd/raid5: fix bug in reshape code when chunk_size decreases.
NeilBrown [Tue, 9 Jun 2009 06:32:22 +0000]
md/raid5: fix bug in reshape code when chunk_size decreases.

Now that we support changing the chunksize, we calculate
"reshape_sectors" to be the max of number of sectors in old
and new chunk size.
However there is one please where we still use 'chunksize'
rather than 'reshape_sectors'.
This causes a reshape that reduces the size of chunks to freeze.

Signed-off-by: NeilBrown <neilb@suse.de>

10 years agomd/raid5 - avoid deadlocks in get_active_stripe during reshape
NeilBrown [Tue, 9 Jun 2009 04:39:59 +0000]
md/raid5 - avoid deadlocks in get_active_stripe during reshape

md has functionality to 'quiesce' and array so that all pending
IO completed and no new IO starts.  This is used to achieve a
stable state before making internal changes.

Currently this quiescing applies equally to normal IO, resync
IO, and reshape IO.
However there is a problem with applying it to reshape IO.
Reshape can have multiple 'stripe_heads' that must be active together.
If the quiesce come between allocating the first and the last of
such a collection, then we deadlock, as the last will not be allocated
until the quiesce is lifted, the quiesce will not be lifted until the
first (which has been allocated) gets used, and that first cannot be
used until the last is allocated.

It is not necessary to inhibit reshape IO when a quiesce is
requested.  Those places in the code that require a full quiesce will
ensure the reshape thread is not running at all.

So allow reshape requests to get access to new stripe_heads without
being blocked by a 'quiesce'.

This only affects in-place reshapes (i.e. where the array does not
grow or shrink) and these are only newly supported.  So this patch is
not needed in earlier kernels.

Signed-off-by: NeilBrown <neilb@suse.de>

10 years agomd/raid5: use conf->raid_disks in preference to mddev->raid_disk
NeilBrown [Tue, 9 Jun 2009 04:30:31 +0000]
md/raid5: use conf->raid_disks in preference to mddev->raid_disk

mddev->raid_disks can be changed and any time by a request from
user-space.  It is a suggestion as to what number of raid_disks is
desired.

conf->raid_disks can only be changed by the raid5 module with suitable
locks in place.  It is a statement as to the current number of
raid_disks.

There are two places where the latter should be used, but the former
is used.  This can lead to a crash when reshaping an array.

This patch changes to mddev-> to conf->

Signed-off-by: NeilBrown <neilb@suse.de>

10 years agoasync: Fix lack of boot-time console due to insufficient synchronization
Linus Torvalds [Mon, 8 Jun 2009 19:31:53 +0000]
async: Fix lack of boot-time console due to insufficient synchronization

Our async work synchronization was broken by "async: make sure
independent async domains can't accidentally entangle" (commit
d5a877e8dd409d8c702986d06485c374b705d340), because it would report
the wrong lowest active async ID when there was both running and
pending async work.

This caused things like no being able to read the root filesystem,
resulting in missing console devices and inability to run 'init',
causing a boot-time panic.

This fixes it by properly returning the lowest pending async ID: if
there is any running async work, that will have a lower ID than any
pending work, and we should _not_ look at the pending work list.

There were alternative patches from Jaswinder and James, but this one
also cleans up the code by removing the pointless 'ret' variable and
the unnecesary testing for an empty list around 'for_each_entry()' (if
the list is empty, the for_each_entry() thing just won't execute).

Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=13474
Reported-and-tested-by: Chris Clayton <chris2553@googlemail.com>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoMerge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
Linus Torvalds [Mon, 8 Jun 2009 16:22:53 +0000]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Outline udelay and fix a few issues.
  MIPS: ioctl.h: Fix headers_check warnings
  MIPS: Cobalt: PCI bus is always required to obtain the board ID
  MIPS: Kconfig: Remove "Support for" from Cavium system type
  MIPS: Sibyte: Honor CONFIG_CMDLINE
  SSB: BCM47xx: Export ssb_watchdog_timer_set

10 years agopata_netcell: Fix typo
Alan Cox [Mon, 8 Jun 2009 11:31:00 +0000]
pata_netcell: Fix typo

The previous patch submission had a I typo I didn't catch but Bartlomiej
noted. Guess this proves the point about any patch being risky late in an rc

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoMerge branch 'kvm-updates/2.6.30' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Linus Torvalds [Mon, 8 Jun 2009 16:05:48 +0000]
Merge branch 'kvm-updates/2.6.30' of git://git./virt/kvm/kvm

* 'kvm-updates/2.6.30' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: Explicity initialize cpus_hardware_enabled

10 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6
Linus Torvalds [Mon, 8 Jun 2009 16:04:55 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/bart/ide-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  pdc202xx_old: fix resetproc() method
  pdc202xx_old: fix 'pdc20246_dma_ops'

10 years agoMIPS: Outline udelay and fix a few issues.
Ralf Baechle [Sat, 28 Feb 2009 09:44:28 +0000]
MIPS: Outline udelay and fix a few issues.

Outlining fixes the issue were on certain CPUs such as the R10000 family
the delay loop would need an extra cycle if it overlaps a cacheline
boundary.

The rewrite also fixes build errors with GCC 4.4 which was changed in
way incompatible with the kernel's inline assembly.

Relying on pure C for computation of the delay value removes the need for
explicit.  The price we pay is a slight slowdown of the computation - to
be fixed on another day.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

10 years agoMIPS: ioctl.h: Fix headers_check warnings
Jaswinder Singh Rajput [Thu, 4 Jun 2009 12:35:49 +0000]
MIPS: ioctl.h: Fix headers_check warnings

Make ioctl.h compatible with asm-generic/ioctl.h and userspace

fix the following 'make headers_check' warning:

  usr/include/asm-mips/ioctl.h:64: extern's make no sense in userspace

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

10 years agoMIPS: Cobalt: PCI bus is always required to obtain the board ID
Yoichi Yuasa [Tue, 2 Jun 2009 14:17:07 +0000]
MIPS: Cobalt: PCI bus is always required to obtain the board ID

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

10 years agoMIPS: Kconfig: Remove "Support for" from Cavium system type
Yoichi Yuasa [Tue, 2 Jun 2009 14:15:10 +0000]
MIPS: Kconfig: Remove "Support for" from Cavium system type

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

10 years agoMIPS: Sibyte: Honor CONFIG_CMDLINE
Ralf Baechle [Tue, 2 Jun 2009 18:05:28 +0000]
MIPS: Sibyte: Honor CONFIG_CMDLINE

Original patch by Imre Kaloz <kaloz@openwrt.org>.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

10 years agoSSB: BCM47xx: Export ssb_watchdog_timer_set
Matthieu Castet [Fri, 22 May 2009 20:25:04 +0000]
SSB: BCM47xx: Export ssb_watchdog_timer_set

this patch export ssb_watchdog_timer_set to allow to use it in a Linux
watchdog driver.

Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by : Michael Buesch <mb@bu3sch.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

10 years agoMerge master.kernel.org:/home/rmk/linux-2.6-arm
Linus Torvalds [Mon, 8 Jun 2009 15:29:31 +0000]
Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5543/1: arm: serial amba: add missing declaration in serial.h
  [ARM] pxa: fix pxa27x_udc default pullup GPIO
  [ARM] pxa/imote2: fix UCAM sensor board ADC model number
  mx[23]: don't put clock lookups in __initdata
  fix oops when using console=ttymxcN with N > 0
  [ARM] ARMv7 errata: only apply fixes when running on applicable CPU
  [ARM] 5534/1: kmalloc must return a cache line aligned buffer

10 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
Linus Torvalds [Mon, 8 Jun 2009 14:53:59 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/drzeus/mmc

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  sdhci-of: Fix the wrong accessor to HOSTVER register
  mvsdio: fix config failure with some high speed SDHC cards
  mvsdio: ignore high speed timing requests from the core
  mmc/omap: Use disable_irq_nosync() from within irq handlers.
  sdhci-of: Add fsl,esdhc as a valid compatible to bind against
  mvsdio: allow automatic loading when modular
  mxcmmc: Fix missing return value checking in DMA setup code.
  mxcmmc : Reset the SDHC hardware if software timeout occurs.
  omap_hsmmc: Trivial fix for a typo in comment
  mxcmmc: decrease minimum frequency to make MMC cards work

10 years agoKVM: Explicity initialize cpus_hardware_enabled
Avi Kivity [Sat, 6 Jun 2009 09:34:39 +0000]
KVM: Explicity initialize cpus_hardware_enabled

Under CONFIG_MAXSMP, cpus_hardware_enabled is allocated from the heap and
not statically initialized.  This causes a crash on reboot when kvm thinks
vmx is enabled on random nonexistent cpus and accesses nonexistent percpu
lists.

Fix by explicitly clearing the variable.

Cc: stable@kernel.org
Reported-and-tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Avi Kivity <avi@redhat.com>

10 years ago[ARM] 5543/1: arm: serial amba: add missing declaration in serial.h
Alessandro Rubini [Sat, 6 Jun 2009 09:17:57 +0000]
[ARM] 5543/1: arm: serial amba: add missing declaration in serial.h

This header is sometimes included in the uncompress stage to get
register values, but no <linux/amba/bus.h> can be included there.
So declare "struct amba_device" here before using it in a prototype.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

10 years agopdc202xx_old: fix resetproc() method
Sergei Shtylyov [Sun, 7 Jun 2009 11:52:50 +0000]
pdc202xx_old: fix resetproc() method

pdc202xx_reset() calls pdc202xx_reset_host() twice, for both channels, while
that function actually twiddles the single, shared software reset bit -- the
net effect is a duplicated reset and horrendous 4 second delay happening not
only on a channel reset but also when dma_lost_irq() and dma_clear() methods
are called.  Fold pdc202xx_reset_host() into pdc202xx_reset(), fix printk(),
and move it before the actual reset...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

10 years agopdc202xx_old: fix 'pdc20246_dma_ops'
Sergei Shtylyov [Sun, 7 Jun 2009 11:52:50 +0000]
pdc202xx_old: fix 'pdc20246_dma_ops'

Commit ac95beedf8bc97b24f9540d4da9952f07221c023 (ide: add struct ide_port_ops
(take 2)) erroneously converted the driver's dma_timeout() and dma_lost_irq()
methods to call the driver's resetproc() method regardless of whether it was
defined for this specific controller while it hadn't been defined and hence
called for PDC20246. So the dma_clear() method, the successor of dma_timeout(),
shouldn't exist and the dma_lost_irq() method should be standard for PDC20246.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

10 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes...
Linus Torvalds [Sat, 6 Jun 2009 21:33:54 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  x86/pci: fix mmconfig detection with 32bit near 4g
  PCI: use fixed-up device class when configuring device

10 years agointegrity: fix IMA inode leak
Hugh Dickins [Sat, 6 Jun 2009 20:18:09 +0000]
integrity: fix IMA inode leak

CONFIG_IMA=y inode activity leaks iint_cache and radix_tree_node objects
until the system runs out of memory.  Nowhere is calling ima_inode_free()
a.k.a. ima_iint_delete().  Fix that by calling it from destroy_inode().

Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
Linus Torvalds [Sat, 6 Jun 2009 19:18:14 +0000]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  ext3/4 with synchronous writes gets wedged by Postfix
  Fix nobh_truncate_page() to not pass stack garbage to get_block()

10 years agoMerge branch 'upstream-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarz...
Linus Torvalds [Sat, 6 Jun 2009 19:17:03 +0000]
Merge branch 'upstream-linus2' of git://git./linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] pata_ali: Use IGN_SIMPLEX

10 years agoext3/4 with synchronous writes gets wedged by Postfix
Al Viro [Wed, 13 May 2009 18:13:40 +0000]
ext3/4 with synchronous writes gets wedged by Postfix

OK, that's probably the easiest way to do that, as much as I don't like it...
Since iget() et.al. will not accept I_FREEING (will wait to go away
and restart), and since we'd better have serialization between new/free
on fs data structures anyway, we can afford simply skipping I_FREEING
et.al. in insert_inode_locked().

We do that from new_inode, so it won't race with free_inode in any interesting
ways and it won't race with iget (of any origin; nfsd or in case of fs
corruption a lookup) since both still will wait for I_LOCK.

Reviewed-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Jan Kara <jack@suse.cz>
Tested-by: David Watson <dbwatson@ukfsn.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

10 years agoFix nobh_truncate_page() to not pass stack garbage to get_block()
Theodore Ts'o [Tue, 12 May 2009 11:37:56 +0000]
Fix nobh_truncate_page() to not pass stack garbage to get_block()

The nobh_truncate_page() function is used by ext2, exofs, and jfs.  Of
these three, only ext2 and jfs's get_block() function pays attention
to bh->b_size --- which is normally always the filesystem blocksize
except when the get_block() function is called by either
mpage_readpage(), mpage_readpages(), or the direct I/O routines in
fs/direct_io.c.

Unfortunately, nobh_truncate_page() does not initialize map_bh before
calling the filesystem-supplied get_block() function.  So ext2 and jfs
will try to calculate the number of blocks to map by taking stack
garbage and shifting it left by inode->i_blkbits.  This should be
*mostly* harmless (except the filesystem will do some unnneeded work)
unless the stack garbage is less than filesystem's blocksize, in which
case maxblocks will be zero, and the attempt to find out whether or
not the filesystem has a hole at a given logical block will fail, and
the page cache entry might not get zero'ed out.

Also if the stack garbage in in map_bh->state happens to have the
BH_Mapped bit set, there could be an attempt to call readpage() on a
non-existent page, which could cause nobh_truncate_page() to return an
error when it should not.

Fix this by initializing map_bh->state and map_bh->size.

Fortunately, it's probably fairly unlikely that ext2 and jfs users
mount with nobh these days.

Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

10 years ago[libata] pata_ali: Use IGN_SIMPLEX
Alan Cox [Wed, 13 May 2009 14:02:27 +0000]
[libata] pata_ali: Use IGN_SIMPLEX

Some ALi devices report simplex if they have been disabled and re-enabled, and
restoring the byte does not work. Ignore it - the needed supporting logic is
already present for the SATA ULi ports.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

10 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable
Linus Torvalds [Fri, 5 Jun 2009 18:54:28 +0000]
Merge git://git./linux/kernel/git/mason/btrfs-unstable

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: Fix oops and use after free during space balancing
  Btrfs: set device->total_disk_bytes when adding new device

10 years agomtd: davinci nand: update clock naming
Kevin Hilman [Fri, 5 Jun 2009 17:48:08 +0000]
mtd: davinci nand: update clock naming

DaVinci clock support has been updated in mainline.
Update clock names accordingly.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

10 years agoMerge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzi...
Linus Torvalds [Fri, 5 Jun 2009 18:53:44 +0000]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ata_piix: Add HP Compaq nc6000 to the broken poweroff list
  ahci: add warning messages for hp laptops with broken suspend
  pata_efar: fix PIO2 underclocking
  pata_legacy: wait for async probing

10 years agoata_piix: Add HP Compaq nc6000 to the broken poweroff list
Ville Syrjala [Mon, 18 May 2009 22:37:44 +0000]
ata_piix: Add HP Compaq nc6000 to the broken poweroff list

HP Compaq nc6000 suffers from the double disk spindown issue.
Add it to the broken poweroff DMI list.

Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

10 years agoahci: add warning messages for hp laptops with broken suspend
Tejun Heo [Sat, 30 May 2009 11:50:12 +0000]
ahci: add warning messages for hp laptops with broken suspend

Harddisks on HP dv[4-6] and HDX18 fail to come online after resume on
earlier BIOSen.  Fortunately, HP recently released BIOS updates for
all machines to fix the issue.  Detect old BIOSen, warn the user to
update BIOS on boot and suspend attempts and fail suspend.

Kudos to all the bug reporters.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: kernel.org@epperson.homelinux.net
Cc: emisca@gmail.com
Cc: Gadi Cohen <dragon@wastelands.net>
Cc: Paul Swanson <paul@procursa.com>
Cc: s@ourada.org
Cc: Trevor Davenport <trevor.davenport@gmail.com>
Cc: corruptor1972 <steven_tierney@yahoo.co.uk>
Cc: Victoria Wilson <mail@vwilson.co.uk>
Cc: khiraly <khiraly.list@gmail.com>
Cc: Sean <wollombi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

10 years agopata_efar: fix PIO2 underclocking
Sergei Shtylyov [Mon, 1 Jun 2009 19:42:10 +0000]
pata_efar: fix PIO2 underclocking

Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the PIIX/ICH drivers do.
Also, fix/rephrase some comments while at it.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>