[PATCH] EDAC: drivers for Radisys 82600
Alan Cox [Thu, 19 Jan 2006 01:44:12 +0000 (17:44 -0800)]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

drivers/edac/r82600_edac.c [new file with mode: 0644]

diff --git a/drivers/edac/r82600_edac.c b/drivers/edac/r82600_edac.c
new file mode 100644 (file)
index 0000000..b6399a5
--- /dev/null
@@ -0,0 +1,407 @@
+/*
+ * Radisys 82600 Embedded chipset Memory Controller kernel module
+ * (C) 2005 EADS Astrium
+ * This file may be distributed under the terms of the
+ * GNU General Public License.
+ *
+ * Written by Tim Small <tim@buttersideup.com>, based on work by Thayne
+ * Harbaugh, Dan Hollis <goemon at anime dot net> and others.
+ *
+ * $Id: edac_r82600.c,v 1.1.2.6 2005/10/05 00:43:44 dsp_llnl Exp $
+ *
+ * Written with reference to 82600 High Integration Dual PCI System
+ * Controller Data Book:
+ * http://www.radisys.com/files/support_downloads/007-01277-0002.82600DataBook.pdf
+ * references to this document given in []
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/init.h>
+
+#include <linux/pci.h>
+#include <linux/pci_ids.h>
+
+#include <linux/slab.h>
+
+#include "edac_mc.h"
+
+/* Radisys say "The 82600 integrates a main memory SDRAM controller that
+ * supports up to four banks of memory. The four banks can support a mix of
+ * sizes of 64 bit wide (72 bits with ECC) Synchronous DRAM (SDRAM) DIMMs,
+ * each of which can be any size from 16MB to 512MB. Both registered (control
+ * signals buffered) and unbuffered DIMM types are supported. Mixing of
+ * registered and unbuffered DIMMs as well as mixing of ECC and non-ECC DIMMs
+ * is not allowed. The 82600 SDRAM interface operates at the same frequency as
+ * the CPU bus, 66MHz, 100MHz or 133MHz."
+ */
+
+#define R82600_NR_CSROWS 4
+#define R82600_NR_CHANS  1
+#define R82600_NR_DIMMS  4
+
+#define R82600_BRIDGE_ID  0x8200
+
+/* Radisys 82600 register addresses - device 0 function 0 - PCI bridge */
+#define R82600_DRAMC   0x57    /* Various SDRAM related control bits
+                                * all bits are R/W
+                                *
+                                * 7    SDRAM ISA Hole Enable
+                                * 6    Flash Page Mode Enable
+                                * 5    ECC Enable: 1=ECC 0=noECC
+                                * 4    DRAM DIMM Type: 1=
+                                * 3    BIOS Alias Disable
+                                * 2    SDRAM BIOS Flash Write Enable
+                                * 1:0  SDRAM Refresh Rate: 00=Disabled
+                                *          01=7.8usec (256Mbit SDRAMs)
+                                *          10=15.6us 11=125usec
+                                */
+
+#define R82600_SDRAMC  0x76    /* "SDRAM Control Register"
+                                * More SDRAM related control bits
+                                * all bits are R/W
+                                *
+                                * 15:8 Reserved.
+                                *
+                                * 7:5  Special SDRAM Mode Select
+                                *
+                                * 4    Force ECC
+                                *
+                                *        1=Drive ECC bits to 0 during
+                                *          write cycles (i.e. ECC test mode)
+                                *
+                                *        0=Normal ECC functioning
+                                *
+                                * 3    Enhanced Paging Enable
+                                *
+                                * 2    CAS# Latency 0=3clks 1=2clks
+                                *
+                                * 1    RAS# to CAS# Delay 0=3 1=2
+                                *
+                                * 0    RAS# Precharge     0=3 1=2
+                                */
+
+#define R82600_EAP     0x80    /* ECC Error Address Pointer Register
+                                *
+                                * 31    Disable Hardware Scrubbing (RW)
+                                *        0=Scrub on corrected read
+                                *        1=Don't scrub on corrected read
+                                *
+                                * 30:12 Error Address Pointer (RO)
+                                *        Upper 19 bits of error address
+                                *
+                                * 11:4  Syndrome Bits (RO)
+                                *
+                                * 3     BSERR# on multibit error (RW)
+                                *        1=enable 0=disable
+                                *
+                                * 2     NMI on Single Bit Eror (RW)
+                                *        1=NMI triggered by SBE n.b. other
+                                *          prerequeists
+                                *        0=NMI not triggered
+                                *
+                                * 1     MBE (R/WC)
+                                *        read 1=MBE at EAP (see above)
+                                *        read 0=no MBE, or SBE occurred first
+                                *        write 1=Clear MBE status (must also
+                                *          clear SBE)
+                                *        write 0=NOP
+                                *
+                                * 1     SBE (R/WC)
+                                *        read 1=SBE at EAP (see above)
+                                *        read 0=no SBE, or MBE occurred first
+                                *        write 1=Clear SBE status (must also
+                                *          clear MBE)
+                                *        write 0=NOP
+                                */
+
+#define R82600_DRBA    0x60    /* + 0x60..0x63 SDRAM Row Boundry Address
+                                *  Registers
+                                *
+                                * 7:0  Address lines 30:24 - upper limit of
+                                * each row [p57]
+                                */
+
+struct r82600_error_info {
+       u32 eapr;
+};
+
+
+static unsigned int disable_hardware_scrub = 0;
+
+
+static void r82600_get_error_info (struct mem_ctl_info *mci,
+               struct r82600_error_info *info)
+{
+       pci_read_config_dword(mci->pdev, R82600_EAP, &info->eapr);
+
+       if (info->eapr & BIT(0))
+               /* Clear error to allow next error to be reported [p.62] */
+               pci_write_bits32(mci->pdev, R82600_EAP,
+                                  ((u32) BIT(0) & (u32) BIT(1)),
+                                  ((u32) BIT(0) & (u32) BIT(1)));
+
+       if (info->eapr & BIT(1))
+               /* Clear error to allow next error to be reported [p.62] */
+               pci_write_bits32(mci->pdev, R82600_EAP,
+                                  ((u32) BIT(0) & (u32) BIT(1)),
+                                  ((u32) BIT(0) & (u32) BIT(1)));
+}
+
+
+static int r82600_process_error_info (struct mem_ctl_info *mci,
+               struct r82600_error_info *info, int handle_errors)
+{
+       int error_found;
+       u32 eapaddr, page;
+       u32 syndrome;
+
+       error_found = 0;
+
+       /* bits 30:12 store the upper 19 bits of the 32 bit error address */
+       eapaddr = ((info->eapr >> 12) & 0x7FFF) << 13;
+       /* Syndrome in bits 11:4 [p.62]       */
+       syndrome = (info->eapr >> 4) & 0xFF;
+
+       /* the R82600 reports at less than page *
+        * granularity (upper 19 bits only)     */
+       page = eapaddr >> PAGE_SHIFT;
+
+       if (info->eapr & BIT(0)) {      /* CE? */
+               error_found = 1;
+
+               if (handle_errors)
+                       edac_mc_handle_ce(
+                           mci, page, 0,       /* not avail */
+                           syndrome,
+                           edac_mc_find_csrow_by_page(mci, page),
+                           0,  /* channel */
+                           mci->ctl_name);
+       }
+
+       if (info->eapr & BIT(1)) {      /* UE? */
+               error_found = 1;
+
+               if (handle_errors)
+                       /* 82600 doesn't give enough info */
+                       edac_mc_handle_ue(mci, page, 0,
+                           edac_mc_find_csrow_by_page(mci, page),
+                           mci->ctl_name);
+       }
+
+       return error_found;
+}
+
+static void r82600_check(struct mem_ctl_info *mci)
+{
+       struct r82600_error_info info;
+
+       debugf1("MC%d: " __FILE__ ": %s()\n", mci->mc_idx, __func__);
+       r82600_get_error_info(mci, &info);
+       r82600_process_error_info(mci, &info, 1);
+}
+
+static int r82600_probe1(struct pci_dev *pdev, int dev_idx)
+{
+       int rc = -ENODEV;
+       int index;
+       struct mem_ctl_info *mci = NULL;
+       u8 dramcr;
+       u32 ecc_on;
+       u32 reg_sdram;
+       u32 eapr;
+       u32 scrub_disabled;
+       u32 sdram_refresh_rate;
+       u32 row_high_limit_last = 0;
+       u32 eap_init_bits;
+
+       debugf0("MC: " __FILE__ ": %s()\n", __func__);
+
+
+       pci_read_config_byte(pdev, R82600_DRAMC, &dramcr);
+       pci_read_config_dword(pdev, R82600_EAP, &eapr);
+
+       ecc_on = dramcr & BIT(5);
+       reg_sdram = dramcr & BIT(4);
+       scrub_disabled = eapr & BIT(31);
+       sdram_refresh_rate = dramcr & (BIT(0) | BIT(1));
+
+       debugf2("MC: " __FILE__ ": %s(): sdram refresh rate = %#0x\n",
+               __func__, sdram_refresh_rate);
+
+       debugf2("MC: " __FILE__ ": %s(): DRAMC register = %#0x\n", __func__,
+               dramcr);
+
+       mci = edac_mc_alloc(0, R82600_NR_CSROWS, R82600_NR_CHANS);
+
+       if (mci == NULL) {
+               rc = -ENOMEM;
+               goto fail;
+       }
+
+       debugf0("MC: " __FILE__ ": %s(): mci = %p\n", __func__, mci);
+
+       mci->pdev = pdev;
+       mci->mtype_cap = MEM_FLAG_RDDR | MEM_FLAG_DDR;
+
+       mci->edac_ctl_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;
+       /* FIXME try to work out if the chip leads have been                 *
+        * used for COM2 instead on this board? [MA6?]       MAYBE:          */
+
+       /* On the R82600, the pins for memory bits 72:65 - i.e. the   *
+        * EC bits are shared with the pins for COM2 (!), so if COM2  *
+        * is enabled, we assume COM2 is wired up, and thus no EDAC   *
+        * is possible.                                               */
+       mci->edac_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;
+       if (ecc_on) {
+               if (scrub_disabled)
+                       debugf3("MC: " __FILE__ ": %s(): mci = %p - "
+                               "Scrubbing disabled! EAP: %#0x\n", __func__,
+                               mci, eapr);
+       } else
+               mci->edac_cap = EDAC_FLAG_NONE;
+
+       mci->mod_name = BS_MOD_STR;
+       mci->mod_ver = "$Revision: 1.1.2.6 $";
+       mci->ctl_name = "R82600";
+       mci->edac_check = r82600_check;
+       mci->ctl_page_to_phys = NULL;
+
+       for (index = 0; index < mci->nr_csrows; index++) {
+               struct csrow_info *csrow = &mci->csrows[index];
+               u8 drbar;       /* sDram Row Boundry Address Register */
+               u32 row_high_limit;
+               u32 row_base;
+
+               /* find the DRAM Chip Select Base address and mask */
+               pci_read_config_byte(mci->pdev, R82600_DRBA + index, &drbar);
+
+               debugf1("MC%d: " __FILE__ ": %s() Row=%d DRBA = %#0x\n",
+                       mci->mc_idx, __func__, index, drbar);
+
+               row_high_limit = ((u32) drbar << 24);
+/*             row_high_limit = ((u32)drbar << 24) | 0xffffffUL; */
+
+               debugf1("MC%d: " __FILE__ ": %s() Row=%d, "
+                       "Boundry Address=%#0x, Last = %#0x \n",
+                       mci->mc_idx, __func__, index, row_high_limit,
+                       row_high_limit_last);
+
+               /* Empty row [p.57] */
+               if (row_high_limit == row_high_limit_last)
+                       continue;
+
+               row_base = row_high_limit_last;
+
+               csrow->first_page = row_base >> PAGE_SHIFT;
+               csrow->last_page = (row_high_limit >> PAGE_SHIFT) - 1;
+               csrow->nr_pages = csrow->last_page - csrow->first_page + 1;
+               /* Error address is top 19 bits - so granularity is      *
+                * 14 bits                                               */
+               csrow->grain = 1 << 14;
+               csrow->mtype = reg_sdram ? MEM_RDDR : MEM_DDR;
+               /* FIXME - check that this is unknowable with this chipset */
+               csrow->dtype = DEV_UNKNOWN;
+
+               /* Mode is global on 82600 */
+               csrow->edac_mode = ecc_on ? EDAC_SECDED : EDAC_NONE;
+               row_high_limit_last = row_high_limit;
+       }
+
+       /* clear counters */
+       /* FIXME should we? */
+
+       if (edac_mc_add_mc(mci)) {
+               debugf3("MC: " __FILE__
+                       ": %s(): failed edac_mc_add_mc()\n", __func__);
+               goto fail;
+       }
+
+       /* get this far and it's successful */
+
+       /* Clear error flags to allow next error to be reported [p.62] */
+       /* Test systems seem to always have the UE flag raised on boot */
+
+       eap_init_bits = BIT(0) & BIT(1);
+       if (disable_hardware_scrub) {
+               eap_init_bits |= BIT(31);
+               debugf3("MC: " __FILE__ ": %s(): Disabling Hardware Scrub "
+                       "(scrub on error)\n", __func__);
+       }
+
+       pci_write_bits32(mci->pdev, R82600_EAP, eap_init_bits,
+                        eap_init_bits);
+
+       debugf3("MC: " __FILE__ ": %s(): success\n", __func__);
+       return 0;
+
+fail:
+       if (mci)
+               edac_mc_free(mci);
+
+       return rc;
+}
+
+/* returns count (>= 0), or negative on error */
+static int __devinit r82600_init_one(struct pci_dev *pdev,
+                                    const struct pci_device_id *ent)
+{
+       debugf0("MC: " __FILE__ ": %s()\n", __func__);
+
+       /* don't need to call pci_device_enable() */
+       return r82600_probe1(pdev, ent->driver_data);
+}
+
+
+static void __devexit r82600_remove_one(struct pci_dev *pdev)
+{
+       struct mem_ctl_info *mci;
+
+       debugf0(__FILE__ ": %s()\n", __func__);
+
+       if (((mci = edac_mc_find_mci_by_pdev(pdev)) != NULL) &&
+           !edac_mc_del_mc(mci))
+               edac_mc_free(mci);
+}
+
+
+static const struct pci_device_id r82600_pci_tbl[] __devinitdata = {
+       {PCI_DEVICE(PCI_VENDOR_ID_RADISYS, R82600_BRIDGE_ID)},
+       {0,}                    /* 0 terminated list. */
+};
+
+MODULE_DEVICE_TABLE(pci, r82600_pci_tbl);
+
+
+static struct pci_driver r82600_driver = {
+       .name = BS_MOD_STR,
+       .probe = r82600_init_one,
+       .remove = __devexit_p(r82600_remove_one),
+       .id_table = r82600_pci_tbl,
+};
+
+
+int __init r82600_init(void)
+{
+       return pci_register_driver(&r82600_driver);
+}
+
+
+static void __exit r82600_exit(void)
+{
+       pci_unregister_driver(&r82600_driver);
+}
+
+
+module_init(r82600_init);
+module_exit(r82600_exit);
+
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Tim Small <tim@buttersideup.com> - WPAD Ltd. "
+             "on behalf of EADS Astrium");
+MODULE_DESCRIPTION("MC support for Radisys 82600 memory controllers");
+
+module_param(disable_hardware_scrub, bool, 0644);
+MODULE_PARM_DESC(disable_hardware_scrub,
+                "If set, disable the chipset's automatic scrub for CEs");