#include <linux/delay.h>
#include <linux/acpi.h>
#include <linux/kallsyms.h>
+#include <linux/dmi.h>
+#include <linux/pci-aspm.h>
+#include <linux/ioport.h>
+#include <asm/dma.h> /* isa_dma_bridge_buggy */
#include "pci.h"
+/*
+ * This quirk function disables memory decoding and releases memory resources
+ * of the device specified by kernel's boot parameter 'pci=resource_alignment='.
+ * It also rounds up size to specified alignment.
+ * Later on, the kernel will assign page-aligned memory resource back
+ * to the device.
+ */
+static void __devinit quirk_resource_alignment(struct pci_dev *dev)
+{
+ int i;
+ struct resource *r;
+ resource_size_t align, size;
+ u16 command;
+
+ if (!pci_is_reassigndev(dev))
+ return;
+
+ if (dev->hdr_type == PCI_HEADER_TYPE_NORMAL &&
+ (dev->class >> 8) == PCI_CLASS_BRIDGE_HOST) {
+ dev_warn(&dev->dev,
+ "Can't reassign resources to host bridge.\n");
+ return;
+ }
+
+ dev_info(&dev->dev,
+ "Disabling memory decoding and releasing memory resources.\n");
+ pci_read_config_word(dev, PCI_COMMAND, &command);
+ command &= ~PCI_COMMAND_MEMORY;
+ pci_write_config_word(dev, PCI_COMMAND, command);
+
+ align = pci_specified_resource_alignment(dev);
+ for (i=0; i < PCI_BRIDGE_RESOURCES; i++) {
+ r = &dev->resource[i];
+ if (!(r->flags & IORESOURCE_MEM))
+ continue;
+ size = resource_size(r);
+ if (size < align) {
+ size = align;
+ dev_info(&dev->dev,
+ "Rounding up size of resource #%d to %#llx.\n",
+ i, (unsigned long long)size);
+ }
+ r->end = size - 1;
+ r->start = 0;
+ }
+ /* Need to disable bridge's resource window,
+ * to enable the kernel to reassign new resource
+ * window later on.
+ */
+ if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE &&
+ (dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
+ for (i = PCI_BRIDGE_RESOURCES; i < PCI_NUM_RESOURCES; i++) {
+ r = &dev->resource[i];
+ if (!(r->flags & IORESOURCE_MEM))
+ continue;
+ r->end = resource_size(r) - 1;
+ r->start = 0;
+ }
+ pci_disable_bridge_window(dev);
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_resource_alignment);
+
+/*
+ * Decoding should be disabled for a PCI device during BAR sizing to avoid
+ * conflict. But doing so may cause problems on host bridge and perhaps other
+ * key system devices. For devices that need to have mmio decoding always-on,
+ * we need to set the dev->mmio_always_on bit.
+ */
+static void __devinit quirk_mmio_always_on(struct pci_dev *dev)
+{
+ if ((dev->class >> 8) == PCI_CLASS_BRIDGE_HOST)
+ dev->mmio_always_on = 1;
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_ANY_ID, PCI_ANY_ID, quirk_mmio_always_on);
+
/* The Mellanox Tavor device gives false positive parity errors
* Mark this device with a broken_parity_status, to allow
* PCI scanning code to "skip" this now blacklisted device.
while ((d = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, d))) {
pci_read_config_byte(d, 0x82, &dlc);
if (!(dlc & 1<<1)) {
- dev_err(&d->dev, "PIIX3: Enabling Passive Release\n");
+ dev_info(&d->dev, "PIIX3: Enabling Passive Release\n");
dlc |= 1<<1;
pci_write_config_byte(d, 0x82, dlc);
}
This appears to be BIOS not version dependent. So presumably there is a
chipset level fix */
-int isa_dma_bridge_buggy;
-EXPORT_SYMBOL(isa_dma_bridge_buggy);
static void __devinit quirk_isa_dma_hangs(struct pci_dev *dev)
{
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_2, quirk_isa_dma_hangs);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_3, quirk_isa_dma_hangs);
-int pci_pci_problems;
-EXPORT_SYMBOL(pci_pci_problems);
+/*
+ * Intel NM10 "TigerPoint" LPC PM1a_STS.BM_STS must be clear
+ * for some HT machines to use C4 w/o hanging.
+ */
+static void __devinit quirk_tigerpoint_bm_sts(struct pci_dev *dev)
+{
+ u32 pmbase;
+ u16 pm1a;
+
+ pci_read_config_dword(dev, 0x40, &pmbase);
+ pmbase = pmbase & 0xff80;
+ pm1a = inw(pmbase);
+
+ if (pm1a & 0x10) {
+ dev_info(&dev->dev, FW_BUG "TigerPoint LPC.BM_STS cleared\n");
+ outw(0x10, pmbase);
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_TGP_LPC, quirk_tigerpoint_bm_sts);
/*
* Chipsets where PCI->PCI transfers vanish or hang
* VIA Apollo KT133 needs PCI latency patch
* Made according to a windows driver based patch by George E. Breese
* see PCI Latency Adjust on http://www.viahardware.com/download/viatweak.shtm
+ * and http://www.georgebreese.com/net/software/#PCI
* Also see http://www.au-ja.org/review-kt133a-1-en.phtml for
* the info on which Mr Breese based his work.
*
* This happens to include the IDE controllers....
*
* VIA only apply this fix when an SB Live! is present but under
- * both Linux and Windows this isnt enough, and we have seen
+ * both Linux and Windows this isn't enough, and we have seen
* corruption without SB Live! but with things like 3 UDMA IDE
* controllers. So we ignore that bit of the VIA recommendation..
*/
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M);
+/*
+ * Some CS5536 BIOSes (for example, the Soekris NET5501 board w/ comBIOS
+ * ver. 1.33 20070103) don't set the correct ISA PCI region header info.
+ * BAR0 should be 8 bytes; instead, it may be set to something like 8k
+ * (which conflicts w/ BAR1's memory range).
+ */
+static void __devinit quirk_cs5536_vsa(struct pci_dev *dev)
+{
+ if (pci_resource_len(dev, 0) != 8) {
+ struct resource *res = &dev->resource[0];
+ res->end = res->start + 8 - 1;
+ dev_info(&dev->dev, "CS5536 ISA bridge bug detected "
+ "(incorrect header); workaround applied.\n");
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, quirk_cs5536_vsa);
+
static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region,
unsigned size, int nr, const char *name)
{
bus_region.end = res->end;
pcibios_bus_to_resource(dev, res, &bus_region);
- pci_claim_resource(dev, nr);
- dev_info(&dev->dev, "quirk: region %04x-%04x claimed by %s\n", region, region + size - 1, name);
+ if (pci_claim_resource(dev, nr) == 0)
+ dev_info(&dev->dev, "quirk: %pR claimed by %s\n",
+ res, name);
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, quirk_piix4_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_3, quirk_piix4_acpi);
+#define ICH_PMBASE 0x40
+#define ICH_ACPI_CNTL 0x44
+#define ICH4_ACPI_EN 0x10
+#define ICH6_ACPI_EN 0x80
+#define ICH4_GPIOBASE 0x58
+#define ICH4_GPIO_CNTL 0x5c
+#define ICH4_GPIO_EN 0x10
+#define ICH6_GPIOBASE 0x48
+#define ICH6_GPIO_CNTL 0x4c
+#define ICH6_GPIO_EN 0x10
+
/*
* ICH4, ICH4-M, ICH5, ICH5-M ACPI: Three IO regions pointed to by longwords at
* 0x40 (128 bytes of ACPI, GPIO & TCO registers)
static void __devinit quirk_ich4_lpc_acpi(struct pci_dev *dev)
{
u32 region;
+ u8 enable;
- pci_read_config_dword(dev, 0x40, ®ion);
- quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES, "ICH4 ACPI/GPIO/TCO");
+ /*
+ * The check for PCIBIOS_MIN_IO is to ensure we won't create a conflict
+ * with low legacy (and fixed) ports. We don't know the decoding
+ * priority and can't tell whether the legacy device or the one created
+ * here is really at that address. This happens on boards with broken
+ * BIOSes.
+ */
+
+ pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable);
+ if (enable & ICH4_ACPI_EN) {
+ pci_read_config_dword(dev, ICH_PMBASE, ®ion);
+ region &= PCI_BASE_ADDRESS_IO_MASK;
+ if (region >= PCIBIOS_MIN_IO)
+ quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES,
+ "ICH4 ACPI/GPIO/TCO");
+ }
- pci_read_config_dword(dev, 0x58, ®ion);
- quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES+1, "ICH4 GPIO");
+ pci_read_config_byte(dev, ICH4_GPIO_CNTL, &enable);
+ if (enable & ICH4_GPIO_EN) {
+ pci_read_config_dword(dev, ICH4_GPIOBASE, ®ion);
+ region &= PCI_BASE_ADDRESS_IO_MASK;
+ if (region >= PCIBIOS_MIN_IO)
+ quirk_io_region(dev, region, 64,
+ PCI_BRIDGE_RESOURCES + 1, "ICH4 GPIO");
+ }
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_0, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, quirk_ich4_lpc_acpi);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1, quirk_ich4_lpc_acpi);
-static void __devinit quirk_ich6_lpc_acpi(struct pci_dev *dev)
+static void __devinit ich6_lpc_acpi_gpio(struct pci_dev *dev)
{
u32 region;
+ u8 enable;
- pci_read_config_dword(dev, 0x40, ®ion);
- quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES, "ICH6 ACPI/GPIO/TCO");
-
- pci_read_config_dword(dev, 0x48, ®ion);
- quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES+1, "ICH6 GPIO");
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_1, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_4, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_2, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_4, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_7, quirk_ich6_lpc_acpi);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_8, quirk_ich6_lpc_acpi);
+ pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable);
+ if (enable & ICH6_ACPI_EN) {
+ pci_read_config_dword(dev, ICH_PMBASE, ®ion);
+ region &= PCI_BASE_ADDRESS_IO_MASK;
+ if (region >= PCIBIOS_MIN_IO)
+ quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES,
+ "ICH6 ACPI/GPIO/TCO");
+ }
+
+ pci_read_config_byte(dev, ICH6_GPIO_CNTL, &enable);
+ if (enable & ICH6_GPIO_EN) {
+ pci_read_config_dword(dev, ICH6_GPIOBASE, ®ion);
+ region &= PCI_BASE_ADDRESS_IO_MASK;
+ if (region >= PCIBIOS_MIN_IO)
+ quirk_io_region(dev, region, 64,
+ PCI_BRIDGE_RESOURCES + 1, "ICH6 GPIO");
+ }
+}
+
+static void __devinit ich6_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name, int dynsize)
+{
+ u32 val;
+ u32 size, base;
+
+ pci_read_config_dword(dev, reg, &val);
+
+ /* Enabled? */
+ if (!(val & 1))
+ return;
+ base = val & 0xfffc;
+ if (dynsize) {
+ /*
+ * This is not correct. It is 16, 32 or 64 bytes depending on
+ * register D31:F0:ADh bits 5:4.
+ *
+ * But this gets us at least _part_ of it.
+ */
+ size = 16;
+ } else {
+ size = 128;
+ }
+ base &= ~(size-1);
+
+ /* Just print it out for now. We should reserve it after more debugging */
+ dev_info(&dev->dev, "%s PIO at %04x-%04x\n", name, base, base+size-1);
+}
+
+static void __devinit quirk_ich6_lpc(struct pci_dev *dev)
+{
+ /* Shared ACPI/GPIO decode with all ICH6+ */
+ ich6_lpc_acpi_gpio(dev);
+
+ /* ICH6-specific generic IO decode */
+ ich6_lpc_generic_decode(dev, 0x84, "LPC Generic IO decode 1", 0);
+ ich6_lpc_generic_decode(dev, 0x88, "LPC Generic IO decode 2", 1);
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc);
+
+static void __devinit ich7_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name)
+{
+ u32 val;
+ u32 mask, base;
+
+ pci_read_config_dword(dev, reg, &val);
+
+ /* Enabled? */
+ if (!(val & 1))
+ return;
+
+ /*
+ * IO base in bits 15:2, mask in bits 23:18, both
+ * are dword-based
+ */
+ base = val & 0xfffc;
+ mask = (val >> 16) & 0xfc;
+ mask |= 3;
+
+ /* Just print it out for now. We should reserve it after more debugging */
+ dev_info(&dev->dev, "%s PIO at %04x (mask %04x)\n", name, base, mask);
+}
+
+/* ICH7-10 has the same common LPC generic IO decode registers */
+static void __devinit quirk_ich7_lpc(struct pci_dev *dev)
+{
+ /* We share the common ACPI/GPIO decode with ICH6 */
+ ich6_lpc_acpi_gpio(dev);
+
+ /* And have 4 ICH7+ generic decodes */
+ ich7_lpc_generic_decode(dev, 0x84, "ICH7 LPC Generic IO decode 1");
+ ich7_lpc_generic_decode(dev, 0x88, "ICH7 LPC Generic IO decode 2");
+ ich7_lpc_generic_decode(dev, 0x8c, "ICH7 LPC Generic IO decode 3");
+ ich7_lpc_generic_decode(dev, 0x90, "ICH7 LPC Generic IO decode 4");
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_1, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_4, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_2, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_4, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_7, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_8, quirk_ich7_lpc);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH10_1, quirk_ich7_lpc);
/*
* VIA ACPI: One IO region pointed to by longword at
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi);
+/*
+ * TI XIO2000a PCIe-PCI Bridge erroneously reports it supports fast back-to-back:
+ * Disable fast back-to-back on the secondary bus segment
+ */
+static void __devinit quirk_xio2000a(struct pci_dev *dev)
+{
+ struct pci_dev *pdev;
+ u16 command;
+
+ dev_warn(&dev->dev, "TI XIO2000a quirk detected; "
+ "secondary bus fast back-to-back transfers disabled\n");
+ list_for_each_entry(pdev, &dev->subordinate->devices, bus_list) {
+ pci_read_config_word(pdev, PCI_COMMAND, &command);
+ if (command & PCI_COMMAND_FAST_BACK)
+ pci_write_config_word(pdev, PCI_COMMAND, command & ~PCI_COMMAND_FAST_BACK);
+ }
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_XIO2000A,
+ quirk_xio2000a);
#ifdef CONFIG_X86_IO_APIC
sis_apic_bug = 1;
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_ANY_ID, quirk_ioapic_rmw);
-
-#define AMD8131_revA0 0x01
-#define AMD8131_revB0 0x11
-#define AMD8131_MISC 0x40
-#define AMD8131_NIOAMODE_BIT 0
-static void quirk_amd_8131_ioapic(struct pci_dev *dev)
-{
- unsigned char tmp;
-
- if (nr_ioapics == 0)
- return;
-
- if (dev->revision == AMD8131_revA0 || dev->revision == AMD8131_revB0) {
- dev_info(&dev->dev, "Fixing up AMD8131 IOAPIC mode\n");
- pci_read_config_byte( dev, AMD8131_MISC, &tmp);
- tmp &= ~(1 << AMD8131_NIOAMODE_BIT);
- pci_write_config_byte( dev, AMD8131_MISC, tmp);
- }
-}
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_ioapic);
-DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_ioapic);
#endif /* CONFIG_X86_IO_APIC */
/*
/*
* Common misconfiguration of the MediaGX/Geode PCI master that will
* reduce PCI bandwidth from 70MB/s to 25MB/s. See the GXM/GXLV/GX1
- * datasheets found at http://www.national.com/ds/GX for info on what
+ * datasheets found at http://www.national.com/analog for info on what
* these bits do. <christer@weinigel.se>
*/
static void quirk_mediagx_master(struct pci_dev *dev)
static void __devinit quirk_amd_ide_mode(struct pci_dev *pdev)
{
- /* set sb600/sb700/sb800 sata to ahci mode */
+ /* set SBX00/Hudson-2 SATA in IDE mode to AHCI mode */
u8 tmp;
pci_read_config_byte(pdev, PCI_CLASS_DEVICE, &tmp);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode);
/*
* Serverworks CSB5 IDE does not fully support native mode
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_ANY_ID, quirk_no_ata_d3);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_ATI, PCI_ANY_ID, quirk_no_ata_d3);
+/* ALi loses some register settings that we cannot then restore */
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, quirk_no_ata_d3);
+/* VIA comes back fine but we need to keep it alive or ACPI GTM failures
+ occur when mode detecting */
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_no_ata_d3);
/* This was originally an Alpha specific thing, but it really fits here.
* The i82375 PCI/EISA bridge appears as non-classified. Fix that.
switch (dev->subsystem_device) {
case 0x1751: /* M2N notebook */
case 0x1821: /* M5N notebook */
+ case 0x1897: /* A6L notebook */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
switch (dev->subsystem_device) {
case 0x12bc: /* HP D330L */
case 0x12bd: /* HP D530 */
+ case 0x006a: /* HP Compaq nx9500 */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82875_HB)
* its on-board VGA controller */
asus_hides_smbus = 1;
}
- else if (dev->device == PCI_DEVICE_ID_INTEL_82845G_IG)
+ else if (dev->device == PCI_DEVICE_ID_INTEL_82801DB_2)
switch(dev->subsystem_device) {
case 0x00b8: /* Compaq Evo D510 CMT */
case 0x00b9: /* Compaq Evo D510 SFF */
+ case 0x00ba: /* Compaq Evo D510 USDT */
+ /* Motherboard doesn't have Host bridge
+ * subvendor/subdevice IDs and on-board VGA
+ * controller is disabled if an AGP card is
+ * inserted, therefore checking USB UHCI
+ * Controller #1 */
asus_hides_smbus = 1;
}
else if (dev->device == PCI_DEVICE_ID_INTEL_82815_CGC)
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82915GM_HB, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG3, asus_hides_smbus_hostbridge);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_IG, asus_hides_smbus_hostbridge);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_2, asus_hides_smbus_hostbridge);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82815_CGC, asus_hides_smbus_hostbridge);
static void asus_hides_smbus_lpc(struct pci_dev *dev)
conf5 &= ~(1 << 24); /* Clear bit 24 */
switch (pdev->device) {
- case PCI_DEVICE_ID_JMICRON_JMB360:
+ case PCI_DEVICE_ID_JMICRON_JMB360: /* SATA single port */
+ case PCI_DEVICE_ID_JMICRON_JMB362: /* SATA dual ports */
+ case PCI_DEVICE_ID_JMICRON_JMB364: /* SATA dual ports */
/* The controller should be in single function ahci mode */
conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */
break;
/* Fall through */
case PCI_DEVICE_ID_JMICRON_JMB361:
case PCI_DEVICE_ID_JMICRON_JMB363:
+ case PCI_DEVICE_ID_JMICRON_JMB369:
/* Enable dual function mode, AHCI on fn 0, IDE fn1 */
/* Set the class codes correctly and then direct IDE 0 */
conf1 |= 0x00C2A1B3; /* Set 0, 1, 4, 5, 7, 8, 13, 15, 17, 22, 23 */
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata);
#endif
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic);
#endif
-int pcie_mch_quirk;
-EXPORT_SYMBOL(pcie_mch_quirk);
-
static void __devinit quirk_pcie_mch(struct pci_dev *pdev)
{
- pcie_mch_quirk = 1;
+ pci_msi_off(pdev);
+ pdev->no_msi = 1;
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260a, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260b, quirk_intel_pcie_pm);
+#ifdef CONFIG_X86_IO_APIC
+/*
+ * Boot interrupts on some chipsets cannot be turned off. For these chipsets,
+ * remap the original interrupt in the linux kernel to the boot interrupt, so
+ * that a PCI device's interrupt handler is installed on the boot interrupt
+ * line instead.
+ */
+static void quirk_reroute_to_boot_interrupts_intel(struct pci_dev *dev)
+{
+ if (noioapicquirk || noioapicreroute)
+ return;
+
+ dev->irq_reroute_variant = INTEL_IRQ_REROUTE_VARIANT;
+ dev_info(&dev->dev, "rerouting interrupts for [%04x:%04x]\n",
+ dev->vendor, dev->device);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel);
+
+/*
+ * On some chipsets we can disable the generation of legacy INTx boot
+ * interrupts.
+ */
+
+/*
+ * IO-APIC1 on 6300ESB generates boot interrupts, see intel order no
+ * 300641-004US, section 5.7.3.
+ */
+#define INTEL_6300_IOAPIC_ABAR 0x40
+#define INTEL_6300_DISABLE_BOOT_IRQ (1<<14)
+
+static void quirk_disable_intel_boot_interrupt(struct pci_dev *dev)
+{
+ u16 pci_config_word;
+
+ if (noioapicquirk)
+ return;
+
+ pci_read_config_word(dev, INTEL_6300_IOAPIC_ABAR, &pci_config_word);
+ pci_config_word |= INTEL_6300_DISABLE_BOOT_IRQ;
+ pci_write_config_word(dev, INTEL_6300_IOAPIC_ABAR, pci_config_word);
+
+ dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
+ dev->vendor, dev->device);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, quirk_disable_intel_boot_interrupt);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, quirk_disable_intel_boot_interrupt);
+
+/*
+ * disable boot interrupts on HT-1000
+ */
+#define BC_HT1000_FEATURE_REG 0x64
+#define BC_HT1000_PIC_REGS_ENABLE (1<<0)
+#define BC_HT1000_MAP_IDX 0xC00
+#define BC_HT1000_MAP_DATA 0xC01
+
+static void quirk_disable_broadcom_boot_interrupt(struct pci_dev *dev)
+{
+ u32 pci_config_dword;
+ u8 irq;
+
+ if (noioapicquirk)
+ return;
+
+ pci_read_config_dword(dev, BC_HT1000_FEATURE_REG, &pci_config_dword);
+ pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword |
+ BC_HT1000_PIC_REGS_ENABLE);
+
+ for (irq = 0x10; irq < 0x10 + 32; irq++) {
+ outb(irq, BC_HT1000_MAP_IDX);
+ outb(0x00, BC_HT1000_MAP_DATA);
+ }
+
+ pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword);
+
+ dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
+ dev->vendor, dev->device);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt);
+
+/*
+ * disable boot interrupts on AMD and ATI chipsets
+ */
+/*
+ * NOIOAMODE needs to be disabled to disable "boot interrupts". For AMD 8131
+ * rev. A0 and B0, NOIOAMODE needs to be disabled anyway to fix IO-APIC mode
+ * (due to an erratum).
+ */
+#define AMD_813X_MISC 0x40
+#define AMD_813X_NOIOAMODE (1<<0)
+#define AMD_813X_REV_B1 0x12
+#define AMD_813X_REV_B2 0x13
+
+static void quirk_disable_amd_813x_boot_interrupt(struct pci_dev *dev)
+{
+ u32 pci_config_dword;
+
+ if (noioapicquirk)
+ return;
+ if ((dev->revision == AMD_813X_REV_B1) ||
+ (dev->revision == AMD_813X_REV_B2))
+ return;
+
+ pci_read_config_dword(dev, AMD_813X_MISC, &pci_config_dword);
+ pci_config_dword &= ~AMD_813X_NOIOAMODE;
+ pci_write_config_dword(dev, AMD_813X_MISC, pci_config_dword);
+
+ dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
+ dev->vendor, dev->device);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt);
+
+#define AMD_8111_PCI_IRQ_ROUTING 0x56
+
+static void quirk_disable_amd_8111_boot_interrupt(struct pci_dev *dev)
+{
+ u16 pci_config_word;
+
+ if (noioapicquirk)
+ return;
+
+ pci_read_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, &pci_config_word);
+ if (!pci_config_word) {
+ dev_info(&dev->dev, "boot interrupts on device [%04x:%04x] "
+ "already disabled\n", dev->vendor, dev->device);
+ return;
+ }
+ pci_write_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, 0);
+ dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n",
+ dev->vendor, dev->device);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt);
+#endif /* CONFIG_X86_IO_APIC */
+
/*
* Toshiba TC86C001 IDE controller reports the standard 8-byte BAR0 size
* but the PIO transfers won't work if BAR0 falls at the odd 8 bytes.
* of parallel ports and <S> is the number of serial ports.
*/
switch (dev->device) {
+ case PCI_DEVICE_ID_NETMOS_9835:
+ /* Well, this rule doesn't hold for the following 9835 device */
+ if (dev->subsystem_vendor == PCI_VENDOR_ID_IBM &&
+ dev->subsystem_device == 0x0299)
+ return;
case PCI_DEVICE_ID_NETMOS_9735:
case PCI_DEVICE_ID_NETMOS_9745:
- case PCI_DEVICE_ID_NETMOS_9835:
case PCI_DEVICE_ID_NETMOS_9845:
case PCI_DEVICE_ID_NETMOS_9855:
if ((dev->class >> 8) == PCI_CLASS_COMMUNICATION_SERIAL &&
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, quirk_e100_interrupt);
+/*
+ * The 82575 and 82598 may experience data corruption issues when transitioning
+ * out of L0S. To prevent this we need to disable L0S on the pci-e link
+ */
+static void __devinit quirk_disable_aspm_l0s(struct pci_dev *dev)
+{
+ dev_info(&dev->dev, "Disabling L0s\n");
+ pci_disable_link_state(dev, PCIE_LINK_STATE_L0S);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a7, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a9, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10b6, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c6, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c7, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c8, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10d6, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10db, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10dd, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10e1, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10ec, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f1, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f4, quirk_disable_aspm_l0s);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1508, quirk_disable_aspm_l0s);
+
static void __devinit fixup_rev1_53c810(struct pci_dev* dev)
{
/* rev 1 ncr53c810 chips don't set the class at all which means
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810);
-static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end)
-{
- while (f < end) {
- if ((f->vendor == dev->vendor || f->vendor == (u16) PCI_ANY_ID) &&
- (f->device == dev->device || f->device == (u16) PCI_ANY_ID)) {
-#ifdef DEBUG
- dev_dbg(&dev->dev, "calling ");
- print_fn_descriptor_symbol("%s\n", f->hook);
-#endif
- f->hook(dev);
- }
- f++;
- }
-}
-
-extern struct pci_fixup __start_pci_fixups_early[];
-extern struct pci_fixup __end_pci_fixups_early[];
-extern struct pci_fixup __start_pci_fixups_header[];
-extern struct pci_fixup __end_pci_fixups_header[];
-extern struct pci_fixup __start_pci_fixups_final[];
-extern struct pci_fixup __end_pci_fixups_final[];
-extern struct pci_fixup __start_pci_fixups_enable[];
-extern struct pci_fixup __end_pci_fixups_enable[];
-extern struct pci_fixup __start_pci_fixups_resume[];
-extern struct pci_fixup __end_pci_fixups_resume[];
-extern struct pci_fixup __start_pci_fixups_resume_early[];
-extern struct pci_fixup __end_pci_fixups_resume_early[];
-extern struct pci_fixup __start_pci_fixups_suspend[];
-extern struct pci_fixup __end_pci_fixups_suspend[];
-
-
-void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev)
-{
- struct pci_fixup *start, *end;
-
- switch(pass) {
- case pci_fixup_early:
- start = __start_pci_fixups_early;
- end = __end_pci_fixups_early;
- break;
-
- case pci_fixup_header:
- start = __start_pci_fixups_header;
- end = __end_pci_fixups_header;
- break;
-
- case pci_fixup_final:
- start = __start_pci_fixups_final;
- end = __end_pci_fixups_final;
- break;
-
- case pci_fixup_enable:
- start = __start_pci_fixups_enable;
- end = __end_pci_fixups_enable;
- break;
-
- case pci_fixup_resume:
- start = __start_pci_fixups_resume;
- end = __end_pci_fixups_resume;
- break;
-
- case pci_fixup_resume_early:
- start = __start_pci_fixups_resume_early;
- end = __end_pci_fixups_resume_early;
- break;
-
- case pci_fixup_suspend:
- start = __start_pci_fixups_suspend;
- end = __end_pci_fixups_suspend;
- break;
-
- default:
- /* stupid compiler warning, you would think with an enum... */
- return;
- }
- pci_do_fixups(dev, start, end);
-}
-EXPORT_SYMBOL(pci_fixup_device);
-
/* Enable 1k I/O space granularity on the Intel P64H2 */
static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev)
{
/*
* Disable PCI Bus Parking and PCI Master read caching on CX700
* which causes unspecified timing errors with a VT6212L on the PCI
- * bus leading to USB2.0 packet loss. The defaults are that these
- * features are turned off but some BIOSes turn them on.
+ * bus leading to USB2.0 packet loss.
+ *
+ * This quirk is only enabled if a second (on the external PCI bus)
+ * VT6212L is found -- the CX700 core itself also contains a USB
+ * host controller with the same PCI ID as the VT6212L.
*/
+ /* Count VT6212L instances */
+ struct pci_dev *p = pci_get_device(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_8235_USB_2, NULL);
uint8_t b;
+
+ /* p should contain the first (internal) VT6212L -- see if we have
+ an external one by searching again */
+ p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235_USB_2, p);
+ if (!p)
+ return;
+ pci_dev_put(p);
+
if (pci_read_config_byte(dev, 0x76, &b) == 0) {
if (b & 0x40) {
/* Turn off PCI Bus Parking */
}
}
}
-DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_VIA, 0x324e, quirk_via_cx700_pci_parking_caching);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0x324e, quirk_via_cx700_pci_parking_caching);
/*
* For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the
static void __devinit quirk_brcm_570x_limit_vpd(struct pci_dev *dev)
{
/*
- * Only disable the VPD capability for 5706, 5708, 5708S and 5709 rev. A
+ * Only disable the VPD capability for 5706, 5706S, 5708,
+ * 5708S and 5709 rev. A
*/
if ((dev->device == PCI_DEVICE_ID_NX2_5706) ||
+ (dev->device == PCI_DEVICE_ID_NX2_5706S) ||
(dev->device == PCI_DEVICE_ID_NX2_5708) ||
(dev->device == PCI_DEVICE_ID_NX2_5708S) ||
((dev->device == PCI_DEVICE_ID_NX2_5709) &&
}
}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_BROADCOM,
- PCI_DEVICE_ID_NX2_5706,
- quirk_brcm_570x_limit_vpd);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_BROADCOM,
- PCI_DEVICE_ID_NX2_5706S,
- quirk_brcm_570x_limit_vpd);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_BROADCOM,
- PCI_DEVICE_ID_NX2_5708,
- quirk_brcm_570x_limit_vpd);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_BROADCOM,
- PCI_DEVICE_ID_NX2_5708S,
- quirk_brcm_570x_limit_vpd);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_BROADCOM,
- PCI_DEVICE_ID_NX2_5709,
- quirk_brcm_570x_limit_vpd);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_BROADCOM,
- PCI_DEVICE_ID_NX2_5709S,
- quirk_brcm_570x_limit_vpd);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5706,
+ quirk_brcm_570x_limit_vpd);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5706S,
+ quirk_brcm_570x_limit_vpd);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5708,
+ quirk_brcm_570x_limit_vpd);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5708S,
+ quirk_brcm_570x_limit_vpd);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5709,
+ quirk_brcm_570x_limit_vpd);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM,
+ PCI_DEVICE_ID_NX2_5709S,
+ quirk_brcm_570x_limit_vpd);
+
+/* Originally in EDAC sources for i82875P:
+ * Intel tells BIOS developers to hide device 6 which
+ * configures the overflow device access containing
+ * the DRBs - this is where we expose device 6.
+ * http://www.x86-secret.com/articles/tweak/pat/patsecrets-2.htm
+ */
+static void __devinit quirk_unhide_mch_dev6(struct pci_dev *dev)
+{
+ u8 reg;
+
+ if (pci_read_config_byte(dev, 0xF4, ®) == 0 && !(reg & 0x02)) {
+ dev_info(&dev->dev, "Enabling MCH 'Overflow' Device\n");
+ pci_write_config_byte(dev, 0xF4, reg | 0x02);
+ }
+}
+
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB,
+ quirk_unhide_mch_dev6);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB,
+ quirk_unhide_mch_dev6);
+
+#ifdef CONFIG_TILE
+/*
+ * The Tilera TILEmpower platform needs to set the link speed
+ * to 2.5GT(Giga-Transfers)/s (Gen 1). The default link speed
+ * setting is 5GT/s (Gen 2). 0x98 is the Link Control2 PCIe
+ * capability register of the PEX8624 PCIe switch. The switch
+ * supports link speed auto negotiation, but falsely sets
+ * the link speed to 5GT/s.
+ */
+static void __devinit quirk_tile_plx_gen1(struct pci_dev *dev)
+{
+ if (tile_plx_gen1) {
+ pci_write_config_dword(dev, 0x98, 0x1);
+ mdelay(50);
+ }
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8624, quirk_tile_plx_gen1);
+#endif /* CONFIG_TILE */
#ifdef CONFIG_PCI_MSI
/* Some chipsets do not support MSI. We cannot easily rely on setting
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS480, quirk_disable_all_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3336, quirk_disable_all_msi);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3351, quirk_disable_all_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3364, quirk_disable_all_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8380_0, quirk_disable_all_msi);
/* Disable MSI on chipsets that are known to not support it */
static void __devinit quirk_disable_msi(struct pci_dev *dev)
}
}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0xa238, quirk_disable_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x5a3f, quirk_disable_msi);
+
+/*
+ * The APC bridge device in AMD 780 family northbridges has some random
+ * OEM subsystem ID in its vendor ID register (erratum 18), so instead
+ * we use the possible vendor/device IDs of the host bridge for the
+ * declared quirk, and search for the APC bridge by slot number.
+ */
+static void __devinit quirk_amd_780_apc_msi(struct pci_dev *host_bridge)
+{
+ struct pci_dev *apc_bridge;
+
+ apc_bridge = pci_get_slot(host_bridge->bus, PCI_DEVFN(1, 0));
+ if (apc_bridge) {
+ if (apc_bridge->device == 0x9602)
+ quirk_disable_msi(apc_bridge);
+ pci_dev_put(apc_bridge);
+ }
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9600, quirk_amd_780_apc_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9601, quirk_amd_780_apc_msi);
/* Go through the list of Hypertransport capabilities and
* return 1 if a HT MSI capability is found and enabled */
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE,
quirk_msi_ht_cap);
-
/* The nVidia CK804 chipset may have 2 HT MSI mappings.
* MSI are supported if the MSI capability set in any of these mappings.
*/
PCI_DEVICE_ID_SERVERWORKS_HT1000_PXB,
ht_enable_msi_mapping);
-static void __devinit nv_msi_ht_cap_quirk(struct pci_dev *dev)
-{
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE,
+ ht_enable_msi_mapping);
+
+/* The P5N32-SLI motherboards from Asus have a problem with msi
+ * for the MCP55 NIC. It is not yet determined whether the msi problem
+ * also affects other devices. As for now, turn off msi for this device.
+ */
+static void __devinit nvenet_msi_disable(struct pci_dev *dev)
+{
+ const char *board_name = dmi_get_system_info(DMI_BOARD_NAME);
+
+ if (board_name &&
+ (strstr(board_name, "P5N32-SLI PREMIUM") ||
+ strstr(board_name, "P5N32-E SLI"))) {
+ dev_info(&dev->dev,
+ "Disabling msi for MCP55 NIC on P5N32-SLI\n");
+ dev->no_msi = 1;
+ }
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA,
+ PCI_DEVICE_ID_NVIDIA_NVENET_15,
+ nvenet_msi_disable);
+
+/*
+ * Some versions of the MCP55 bridge from nvidia have a legacy irq routing
+ * config register. This register controls the routing of legacy interrupts
+ * from devices that route through the MCP55. If this register is misprogramed
+ * interrupts are only sent to the bsp, unlike conventional systems where the
+ * irq is broadxast to all online cpus. Not having this register set
+ * properly prevents kdump from booting up properly, so lets make sure that
+ * we have it set correctly.
+ * Note this is an undocumented register.
+ */
+static void __devinit nvbridge_check_legacy_irq_routing(struct pci_dev *dev)
+{
+ u32 cfg;
+
+ if (!pci_find_capability(dev, PCI_CAP_ID_HT))
+ return;
+
+ pci_read_config_dword(dev, 0x74, &cfg);
+
+ if (cfg & ((1 << 2) | (1 << 15))) {
+ printk(KERN_INFO "Rewriting irq routing register on MCP55\n");
+ cfg &= ~((1 << 2) | (1 << 15));
+ pci_write_config_dword(dev, 0x74, cfg);
+ }
+}
+
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA,
+ PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V0,
+ nvbridge_check_legacy_irq_routing);
+
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA,
+ PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V4,
+ nvbridge_check_legacy_irq_routing);
+
+static int __devinit ht_check_msi_mapping(struct pci_dev *dev)
+{
+ int pos, ttl = 48;
+ int found = 0;
+
+ /* check if there is HT MSI cap or enabled on this device */
+ pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING);
+ while (pos && ttl--) {
+ u8 flags;
+
+ if (found < 1)
+ found = 1;
+ if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS,
+ &flags) == 0) {
+ if (flags & HT_MSI_FLAGS_ENABLE) {
+ if (found < 2) {
+ found = 2;
+ break;
+ }
+ }
+ }
+ pos = pci_find_next_ht_capability(dev, pos,
+ HT_CAPTYPE_MSI_MAPPING);
+ }
+
+ return found;
+}
+
+static int __devinit host_bridge_with_leaf(struct pci_dev *host_bridge)
+{
+ struct pci_dev *dev;
+ int pos;
+ int i, dev_no;
+ int found = 0;
+
+ dev_no = host_bridge->devfn >> 3;
+ for (i = dev_no + 1; i < 0x20; i++) {
+ dev = pci_get_slot(host_bridge->bus, PCI_DEVFN(i, 0));
+ if (!dev)
+ continue;
+
+ /* found next host bridge ?*/
+ pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE);
+ if (pos != 0) {
+ pci_dev_put(dev);
+ break;
+ }
+
+ if (ht_check_msi_mapping(dev)) {
+ found = 1;
+ pci_dev_put(dev);
+ break;
+ }
+ pci_dev_put(dev);
+ }
+
+ return found;
+}
+
+#define PCI_HT_CAP_SLAVE_CTRL0 4 /* link control */
+#define PCI_HT_CAP_SLAVE_CTRL1 8 /* link control to */
+
+static int __devinit is_end_of_ht_chain(struct pci_dev *dev)
+{
+ int pos, ctrl_off;
+ int end = 0;
+ u16 flags, ctrl;
+
+ pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE);
+
+ if (!pos)
+ goto out;
+
+ pci_read_config_word(dev, pos + PCI_CAP_FLAGS, &flags);
+
+ ctrl_off = ((flags >> 10) & 1) ?
+ PCI_HT_CAP_SLAVE_CTRL0 : PCI_HT_CAP_SLAVE_CTRL1;
+ pci_read_config_word(dev, pos + ctrl_off, &ctrl);
+
+ if (ctrl & (1 << 6))
+ end = 1;
+
+out:
+ return end;
+}
+
+static void __devinit nv_ht_enable_msi_mapping(struct pci_dev *dev)
+{
struct pci_dev *host_bridge;
+ int pos;
+ int i, dev_no;
+ int found = 0;
+
+ dev_no = dev->devfn >> 3;
+ for (i = dev_no; i >= 0; i--) {
+ host_bridge = pci_get_slot(dev->bus, PCI_DEVFN(i, 0));
+ if (!host_bridge)
+ continue;
+
+ pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE);
+ if (pos != 0) {
+ found = 1;
+ break;
+ }
+ pci_dev_put(host_bridge);
+ }
+
+ if (!found)
+ return;
+
+ /* don't enable end_device/host_bridge with leaf directly here */
+ if (host_bridge == dev && is_end_of_ht_chain(host_bridge) &&
+ host_bridge_with_leaf(host_bridge))
+ goto out;
+
+ /* root did that ! */
+ if (msi_ht_cap_enabled(host_bridge))
+ goto out;
+
+ ht_enable_msi_mapping(dev);
+
+out:
+ pci_dev_put(host_bridge);
+}
+
+static void __devinit ht_disable_msi_mapping(struct pci_dev *dev)
+{
int pos, ttl = 48;
+ pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING);
+ while (pos && ttl--) {
+ u8 flags;
+
+ if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS,
+ &flags) == 0) {
+ dev_info(&dev->dev, "Disabling HT MSI Mapping\n");
+
+ pci_write_config_byte(dev, pos + HT_MSI_FLAGS,
+ flags & ~HT_MSI_FLAGS_ENABLE);
+ }
+ pos = pci_find_next_ht_capability(dev, pos,
+ HT_CAPTYPE_MSI_MAPPING);
+ }
+}
+
+static void __devinit __nv_msi_ht_cap_quirk(struct pci_dev *dev, int all)
+{
+ struct pci_dev *host_bridge;
+ int pos;
+ int found;
+
+ if (!pci_msi_enabled())
+ return;
+
+ /* check if there is HT MSI cap or enabled on this device */
+ found = ht_check_msi_mapping(dev);
+
+ /* no HT MSI CAP */
+ if (found == 0)
+ return;
+
/*
* HT MSI mapping should be disabled on devices that are below
* a non-Hypertransport host bridge. Locate the host bridge...
pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE);
if (pos != 0) {
/* Host bridge is to HT */
- ht_enable_msi_mapping(dev);
+ if (found == 1) {
+ /* it is not enabled, try to enable it */
+ if (all)
+ ht_enable_msi_mapping(dev);
+ else
+ nv_ht_enable_msi_mapping(dev);
+ }
return;
}
+ /* HT MSI is not enabled */
+ if (found == 1)
+ return;
+
/* Host bridge is not to HT, disable HT MSI mapping on this device */
- pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING);
- while (pos && ttl--) {
- u8 flags;
+ ht_disable_msi_mapping(dev);
+}
- if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS,
- &flags) == 0) {
- dev_info(&dev->dev, "Disabling HT MSI mapping");
- pci_write_config_byte(dev, pos + HT_MSI_FLAGS,
- flags & ~HT_MSI_FLAGS_ENABLE);
- }
- pos = pci_find_next_ht_capability(dev, pos,
- HT_CAPTYPE_MSI_MAPPING);
- }
+static void __devinit nv_msi_ht_cap_quirk_all(struct pci_dev *dev)
+{
+ return __nv_msi_ht_cap_quirk(dev, 1);
}
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk);
+
+static void __devinit nv_msi_ht_cap_quirk_leaf(struct pci_dev *dev)
+{
+ return __nv_msi_ht_cap_quirk(dev, 0);
+}
+
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf);
+
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all);
static void __devinit quirk_msi_intx_disable_bug(struct pci_dev *dev)
{
quirk_msi_intx_disable_bug);
#endif /* CONFIG_PCI_MSI */
+
+/* Allow manual resource allocation for PCI hotplug bridges
+ * via pci=hpmemsize=nnM and pci=hpiosize=nnM parameters. For
+ * some PCI-PCI hotplug bridges, like PLX 6254 (former HINT HB6),
+ * kernel fails to allocate resources when hotplug device is
+ * inserted and PCI bus is rescanned.
+ */
+static void __devinit quirk_hotplug_bridge(struct pci_dev *dev)
+{
+ dev->is_hotplug_bridge = 1;
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_HINT, 0x0020, quirk_hotplug_bridge);
+
+/*
+ * This is a quirk for the Ricoh MMC controller found as a part of
+ * some mulifunction chips.
+
+ * This is very similar and based on the ricoh_mmc driver written by
+ * Philip Langdale. Thank you for these magic sequences.
+ *
+ * These chips implement the four main memory card controllers (SD, MMC, MS, xD)
+ * and one or both of cardbus or firewire.
+ *
+ * It happens that they implement SD and MMC
+ * support as separate controllers (and PCI functions). The linux SDHCI
+ * driver supports MMC cards but the chip detects MMC cards in hardware
+ * and directs them to the MMC controller - so the SDHCI driver never sees
+ * them.
+ *
+ * To get around this, we must disable the useless MMC controller.
+ * At that point, the SDHCI controller will start seeing them
+ * It seems to be the case that the relevant PCI registers to deactivate the
+ * MMC controller live on PCI function 0, which might be the cardbus controller
+ * or the firewire controller, depending on the particular chip in question
+ *
+ * This has to be done early, because as soon as we disable the MMC controller
+ * other pci functions shift up one level, e.g. function #2 becomes function
+ * #1, and this will confuse the pci core.
+ */
+
+#ifdef CONFIG_MMC_RICOH_MMC
+static void ricoh_mmc_fixup_rl5c476(struct pci_dev *dev)
+{
+ /* disable via cardbus interface */
+ u8 write_enable;
+ u8 write_target;
+ u8 disable;
+
+ /* disable must be done via function #0 */
+ if (PCI_FUNC(dev->devfn))
+ return;
+
+ pci_read_config_byte(dev, 0xB7, &disable);
+ if (disable & 0x02)
+ return;
+
+ pci_read_config_byte(dev, 0x8E, &write_enable);
+ pci_write_config_byte(dev, 0x8E, 0xAA);
+ pci_read_config_byte(dev, 0x8D, &write_target);
+ pci_write_config_byte(dev, 0x8D, 0xB7);
+ pci_write_config_byte(dev, 0xB7, disable | 0x02);
+ pci_write_config_byte(dev, 0x8E, write_enable);
+ pci_write_config_byte(dev, 0x8D, write_target);
+
+ dev_notice(&dev->dev, "proprietary Ricoh MMC controller disabled (via cardbus function)\n");
+ dev_notice(&dev->dev, "MMC cards are now supported by standard SDHCI controller\n");
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476);
+
+static void ricoh_mmc_fixup_r5c832(struct pci_dev *dev)
+{
+ /* disable via firewire interface */
+ u8 write_enable;
+ u8 disable;
+
+ /* disable must be done via function #0 */
+ if (PCI_FUNC(dev->devfn))
+ return;
+
+ pci_read_config_byte(dev, 0xCB, &disable);
+
+ if (disable & 0x02)
+ return;
+
+ pci_read_config_byte(dev, 0xCA, &write_enable);
+ pci_write_config_byte(dev, 0xCA, 0x57);
+ pci_write_config_byte(dev, 0xCB, disable | 0x02);
+ pci_write_config_byte(dev, 0xCA, write_enable);
+
+ dev_notice(&dev->dev, "proprietary Ricoh MMC controller disabled (via firewire function)\n");
+ dev_notice(&dev->dev, "MMC cards are now supported by standard SDHCI controller\n");
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832);
+#endif /*CONFIG_MMC_RICOH_MMC*/
+
+#if defined(CONFIG_DMAR) || defined(CONFIG_INTR_REMAP)
+#define VTUNCERRMSK_REG 0x1ac
+#define VTD_MSK_SPEC_ERRORS (1 << 31)
+/*
+ * This is a quirk for masking vt-d spec defined errors to platform error
+ * handling logic. With out this, platforms using Intel 7500, 5500 chipsets
+ * (and the derivative chipsets like X58 etc) seem to generate NMI/SMI (based
+ * on the RAS config settings of the platform) when a vt-d fault happens.
+ * The resulting SMI caused the system to hang.
+ *
+ * VT-d spec related errors are already handled by the VT-d OS code, so no
+ * need to report the same error through other channels.
+ */
+static void vtd_mask_spec_errors(struct pci_dev *dev)
+{
+ u32 word;
+
+ pci_read_config_dword(dev, VTUNCERRMSK_REG, &word);
+ pci_write_config_dword(dev, VTUNCERRMSK_REG, word | VTD_MSK_SPEC_ERRORS);
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x342e, vtd_mask_spec_errors);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x3c28, vtd_mask_spec_errors);
+#endif
+
+static void __devinit fixup_ti816x_class(struct pci_dev* dev)
+{
+ /* TI 816x devices do not have class code set when in PCIe boot mode */
+ if (dev->class == PCI_CLASS_NOT_DEFINED) {
+ dev_info(&dev->dev, "Setting PCI class for 816x PCIe device\n");
+ dev->class = PCI_CLASS_MULTIMEDIA_VIDEO;
+ }
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_TI, 0xb800, fixup_ti816x_class);
+
+static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f,
+ struct pci_fixup *end)
+{
+ while (f < end) {
+ if ((f->vendor == dev->vendor || f->vendor == (u16) PCI_ANY_ID) &&
+ (f->device == dev->device || f->device == (u16) PCI_ANY_ID)) {
+ dev_dbg(&dev->dev, "calling %pF\n", f->hook);
+ f->hook(dev);
+ }
+ f++;
+ }
+}
+
+extern struct pci_fixup __start_pci_fixups_early[];
+extern struct pci_fixup __end_pci_fixups_early[];
+extern struct pci_fixup __start_pci_fixups_header[];
+extern struct pci_fixup __end_pci_fixups_header[];
+extern struct pci_fixup __start_pci_fixups_final[];
+extern struct pci_fixup __end_pci_fixups_final[];
+extern struct pci_fixup __start_pci_fixups_enable[];
+extern struct pci_fixup __end_pci_fixups_enable[];
+extern struct pci_fixup __start_pci_fixups_resume[];
+extern struct pci_fixup __end_pci_fixups_resume[];
+extern struct pci_fixup __start_pci_fixups_resume_early[];
+extern struct pci_fixup __end_pci_fixups_resume_early[];
+extern struct pci_fixup __start_pci_fixups_suspend[];
+extern struct pci_fixup __end_pci_fixups_suspend[];
+
+
+void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev)
+{
+ struct pci_fixup *start, *end;
+
+ switch(pass) {
+ case pci_fixup_early:
+ start = __start_pci_fixups_early;
+ end = __end_pci_fixups_early;
+ break;
+
+ case pci_fixup_header:
+ start = __start_pci_fixups_header;
+ end = __end_pci_fixups_header;
+ break;
+
+ case pci_fixup_final:
+ start = __start_pci_fixups_final;
+ end = __end_pci_fixups_final;
+ break;
+
+ case pci_fixup_enable:
+ start = __start_pci_fixups_enable;
+ end = __end_pci_fixups_enable;
+ break;
+
+ case pci_fixup_resume:
+ start = __start_pci_fixups_resume;
+ end = __end_pci_fixups_resume;
+ break;
+
+ case pci_fixup_resume_early:
+ start = __start_pci_fixups_resume_early;
+ end = __end_pci_fixups_resume_early;
+ break;
+
+ case pci_fixup_suspend:
+ start = __start_pci_fixups_suspend;
+ end = __end_pci_fixups_suspend;
+ break;
+
+ default:
+ /* stupid compiler warning, you would think with an enum... */
+ return;
+ }
+ pci_do_fixups(dev, start, end);
+}
+EXPORT_SYMBOL(pci_fixup_device);
+
+static int __init pci_apply_final_quirks(void)
+{
+ struct pci_dev *dev = NULL;
+ u8 cls = 0;
+ u8 tmp;
+
+ if (pci_cache_line_size)
+ printk(KERN_DEBUG "PCI: CLS %u bytes\n",
+ pci_cache_line_size << 2);
+
+ for_each_pci_dev(dev) {
+ pci_fixup_device(pci_fixup_final, dev);
+ /*
+ * If arch hasn't set it explicitly yet, use the CLS
+ * value shared by all PCI devices. If there's a
+ * mismatch, fall back to the default value.
+ */
+ if (!pci_cache_line_size) {
+ pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, &tmp);
+ if (!cls)
+ cls = tmp;
+ if (!tmp || cls == tmp)
+ continue;
+
+ printk(KERN_DEBUG "PCI: CLS mismatch (%u != %u), "
+ "using %u bytes\n", cls << 2, tmp << 2,
+ pci_dfl_cache_line_size << 2);
+ pci_cache_line_size = pci_dfl_cache_line_size;
+ }
+ }
+ if (!pci_cache_line_size) {
+ printk(KERN_DEBUG "PCI: CLS %u bytes, default %u\n",
+ cls << 2, pci_dfl_cache_line_size << 2);
+ pci_cache_line_size = cls ? cls : pci_dfl_cache_line_size;
+ }
+
+ return 0;
+}
+
+fs_initcall_sync(pci_apply_final_quirks);
+
+/*
+ * Followings are device-specific reset methods which can be used to
+ * reset a single function if other methods (e.g. FLR, PM D0->D3) are
+ * not available.
+ */
+static int reset_intel_generic_dev(struct pci_dev *dev, int probe)
+{
+ int pos;
+
+ /* only implement PCI_CLASS_SERIAL_USB at present */
+ if (dev->class == PCI_CLASS_SERIAL_USB) {
+ pos = pci_find_capability(dev, PCI_CAP_ID_VNDR);
+ if (!pos)
+ return -ENOTTY;
+
+ if (probe)
+ return 0;
+
+ pci_write_config_byte(dev, pos + 0x4, 1);
+ msleep(100);
+
+ return 0;
+ } else {
+ return -ENOTTY;
+ }
+}
+
+static int reset_intel_82599_sfp_virtfn(struct pci_dev *dev, int probe)
+{
+ int pos;
+
+ pos = pci_find_capability(dev, PCI_CAP_ID_EXP);
+ if (!pos)
+ return -ENOTTY;
+
+ if (probe)
+ return 0;
+
+ pci_write_config_word(dev, pos + PCI_EXP_DEVCTL,
+ PCI_EXP_DEVCTL_BCR_FLR);
+ msleep(100);
+
+ return 0;
+}
+
+#define PCI_DEVICE_ID_INTEL_82599_SFP_VF 0x10ed
+
+static const struct pci_dev_reset_methods pci_dev_reset_methods[] = {
+ { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82599_SFP_VF,
+ reset_intel_82599_sfp_virtfn },
+ { PCI_VENDOR_ID_INTEL, PCI_ANY_ID,
+ reset_intel_generic_dev },
+ { 0 }
+};
+
+int pci_dev_specific_reset(struct pci_dev *dev, int probe)
+{
+ const struct pci_dev_reset_methods *i;
+
+ for (i = pci_dev_reset_methods; i->reset; i++) {
+ if ((i->vendor == dev->vendor ||
+ i->vendor == (u16)PCI_ANY_ID) &&
+ (i->device == dev->device ||
+ i->device == (u16)PCI_ANY_ID))
+ return i->reset(dev, probe);
+ }
+
+ return -ENOTTY;
+}
Code Review / linux-2.6.git / blobdiff