drivers/tty/serial/mfd.c

   1 /*
   2  * mfd.c: driver for High Speed UART device of Intel Medfield platform
   3  *
   4  * Refer pxa.c, 8250.c and some other drivers in drivers/serial/
   5  *
   6  * (C) Copyright 2010 Intel Corporation
   7  *
   8  * This program is free software; you can redistribute it and/or
   9  * modify it under the terms of the GNU General Public License
  10  * as published by the Free Software Foundation; version 2
  11  * of the License.
  12  */
  13
  14 /* Notes:
  15  * 1. DMA channel allocation: 0/1 channel are assigned to port 0,
  16  *    2/3 chan to port 1, 4/5 chan to port 3. Even number chans
  17  *    are used for RX, odd chans for TX
  18  *
  19  * 2. In A0 stepping, UART will not support TX half empty flag
  20  *
  21  * 3. The RI/DSR/DCD/DTR are not pinned out, DCD & DSR are always
  22  *    asserted, only when the HW is reset the DDCD and DDSR will
  23  *    be triggered
  24  */
  25
  26 #include <linux/module.h>
  27 #include <linux/init.h>
  28 #include <linux/console.h>
  29 #include <linux/sysrq.h>
  30 #include <linux/slab.h>
  31 #include <linux/serial_reg.h>
  32 #include <linux/circ_buf.h>
  33 #include <linux/delay.h>
  34 #include <linux/interrupt.h>
  35 #include <linux/tty.h>
  36 #include <linux/tty_flip.h>
  37 #include <linux/serial_core.h>
  38 #include <linux/serial_mfd.h>
  39 #include <linux/dma-mapping.h>
  40 #include <linux/pci.h>
  41 #include <linux/io.h>
  42 #include <linux/debugfs.h>
  43
  44 #define  MFD_HSU_A0_STEPPING    1
  45
  46 #define HSU_DMA_BUF_SIZE        2048
  47
  48 #define chan_readl(chan, offset)        readl(chan->reg + offset)
  49 #define chan_writel(chan, offset, val)  writel(val, chan->reg + offset)
  50
  51 #define mfd_readl(obj, offset)          readl(obj->reg + offset)
  52 #define mfd_writel(obj, offset, val)    writel(val, obj->reg + offset)
  53
  54 #define HSU_DMA_TIMEOUT_CHECK_FREQ      (HZ/10)
  55
  56 struct hsu_dma_buffer {
  57         u8              *buf;
  58         dma_addr_t      dma_addr;
  59         u32             dma_size;
  60         u32             ofs;
  61 };
  62
  63 struct hsu_dma_chan {
  64         u32     id;
  65         enum dma_data_direction dirt;
  66         struct uart_hsu_port    *uport;
  67         void __iomem            *reg;
  68         struct timer_list       rx_timer; /* only needed by RX channel */
  69 };
  70
  71 struct uart_hsu_port {
  72         struct uart_port        port;
  73         unsigned char           ier;
  74         unsigned char           lcr;
  75         unsigned char           mcr;
  76         unsigned int            lsr_break_flag;
  77         char                    name[12];
  78         int                     index;
  79         struct device           *dev;
  80
  81         struct hsu_dma_chan     *txc;
  82         struct hsu_dma_chan     *rxc;
  83         struct hsu_dma_buffer   txbuf;
  84         struct hsu_dma_buffer   rxbuf;
  85         int                     use_dma;        /* flag for DMA/PIO */
  86         int                     running;
  87         int                     dma_tx_on;
  88 };
  89
  90 /* Top level data structure of HSU */
  91 struct hsu_port {
  92         void __iomem    *reg;
  93         unsigned long   paddr;
  94         unsigned long   iolen;
  95         u32             irq;
  96
  97         struct uart_hsu_port    port[3];
  98         struct hsu_dma_chan     chans[10];
  99
 100         struct dentry *debugfs;
 101 };
 102
 103 static inline unsigned int serial_in(struct uart_hsu_port *up, int offset)
 104 {
 105         unsigned int val;
 106
 107         if (offset > UART_MSR) {
 108                 offset <<= 2;
 109                 val = readl(up->port.membase + offset);
 110         } else
 111                 val = (unsigned int)readb(up->port.membase + offset);
 112
 113         return val;
 114 }
 115
 116 static inline void serial_out(struct uart_hsu_port *up, int offset, int value)
 117 {
 118         if (offset > UART_MSR) {
 119                 offset <<= 2;
 120                 writel(value, up->port.membase + offset);
 121         } else {
 122                 unsigned char val = value & 0xff;
 123                 writeb(val, up->port.membase + offset);
 124         }
 125 }
 126
 127 #ifdef CONFIG_DEBUG_FS
 128
 129 #define HSU_REGS_BUFSIZE        1024
 130
 131 static int hsu_show_regs_open(struct inode *inode, struct file *file)
 132 {
 133         file->private_data = inode->i_private;
 134         return 0;
 135 }
 136
 137 static ssize_t port_show_regs(struct file *file, char __user *user_buf,
 138                                 size_t count, loff_t *ppos)
 139 {
 140         struct uart_hsu_port *up = file->private_data;
 141         char *buf;
 142         u32 len = 0;
 143         ssize_t ret;
 144
 145         buf = kzalloc(HSU_REGS_BUFSIZE, GFP_KERNEL);
 146         if (!buf)
 147                 return 0;
 148
 149         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 150                         "MFD HSU port[%d] regs:\n", up->index);
 151
 152         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 153                         "=================================\n");
 154         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 155                         "IER: \t\t0x%08x\n", serial_in(up, UART_IER));
 156         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 157                         "IIR: \t\t0x%08x\n", serial_in(up, UART_IIR));
 158         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 159                         "LCR: \t\t0x%08x\n", serial_in(up, UART_LCR));
 160         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 161                         "MCR: \t\t0x%08x\n", serial_in(up, UART_MCR));
 162         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 163                         "LSR: \t\t0x%08x\n", serial_in(up, UART_LSR));
 164         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 165                         "MSR: \t\t0x%08x\n", serial_in(up, UART_MSR));
 166         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 167                         "FOR: \t\t0x%08x\n", serial_in(up, UART_FOR));
 168         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 169                         "PS: \t\t0x%08x\n", serial_in(up, UART_PS));
 170         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 171                         "MUL: \t\t0x%08x\n", serial_in(up, UART_MUL));
 172         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 173                         "DIV: \t\t0x%08x\n", serial_in(up, UART_DIV));
 174
 175         if (len > HSU_REGS_BUFSIZE)
 176                 len = HSU_REGS_BUFSIZE;
 177
 178         ret =  simple_read_from_buffer(user_buf, count, ppos, buf, len);
 179         kfree(buf);
 180         return ret;
 181 }
 182
 183 static ssize_t dma_show_regs(struct file *file, char __user *user_buf,
 184                                 size_t count, loff_t *ppos)
 185 {
 186         struct hsu_dma_chan *chan = file->private_data;
 187         char *buf;
 188         u32 len = 0;
 189         ssize_t ret;
 190
 191         buf = kzalloc(HSU_REGS_BUFSIZE, GFP_KERNEL);
 192         if (!buf)
 193                 return 0;
 194
 195         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 196                         "MFD HSU DMA channel [%d] regs:\n", chan->id);
 197
 198         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 199                         "=================================\n");
 200         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 201                         "CR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_CR));
 202         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 203                         "DCR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_DCR));
 204         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 205                         "BSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_BSR));
 206         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 207                         "MOTSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_MOTSR));
 208         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 209                         "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D0SAR));
 210         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 211                         "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D0TSR));
 212         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 213                         "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D1SAR));
 214         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 215                         "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D1TSR));
 216         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 217                         "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D2SAR));
 218         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 219                         "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D2TSR));
 220         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 221                         "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D3SAR));
 222         len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
 223                         "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D3TSR));
 224
 225         if (len > HSU_REGS_BUFSIZE)
 226                 len = HSU_REGS_BUFSIZE;
 227
 228         ret =  simple_read_from_buffer(user_buf, count, ppos, buf, len);
 229         kfree(buf);
 230         return ret;
 231 }
 232
 233 static const struct file_operations port_regs_ops = {
 234         .owner          = THIS_MODULE,
 235         .open           = hsu_show_regs_open,
 236         .read           = port_show_regs,
 237         .llseek         = default_llseek,
 238 };
 239
 240 static const struct file_operations dma_regs_ops = {
 241         .owner          = THIS_MODULE,
 242         .open           = hsu_show_regs_open,
 243         .read           = dma_show_regs,
 244         .llseek         = default_llseek,
 245 };
 246
 247 static int hsu_debugfs_init(struct hsu_port *hsu)
 248 {
 249         int i;
 250         char name[32];
 251
 252         hsu->debugfs = debugfs_create_dir("hsu", NULL);
 253         if (!hsu->debugfs)
 254                 return -ENOMEM;
 255
 256         for (i = 0; i < 3; i++) {
 257                 snprintf(name, sizeof(name), "port_%d_regs", i);
 258                 debugfs_create_file(name, S_IFREG | S_IRUGO,
 259                         hsu->debugfs, (void *)(&hsu->port[i]), &port_regs_ops);
 260         }
 261
 262         for (i = 0; i < 6; i++) {
 263                 snprintf(name, sizeof(name), "dma_chan_%d_regs", i);
 264                 debugfs_create_file(name, S_IFREG | S_IRUGO,
 265                         hsu->debugfs, (void *)&hsu->chans[i], &dma_regs_ops);
 266         }
 267
 268         return 0;
 269 }
 270
 271 static void hsu_debugfs_remove(struct hsu_port *hsu)
 272 {
 273         if (hsu->debugfs)
 274                 debugfs_remove_recursive(hsu->debugfs);
 275 }
 276
 277 #else
 278 static inline int hsu_debugfs_init(struct hsu_port *hsu)
 279 {
 280         return 0;
 281 }
 282
 283 static inline void hsu_debugfs_remove(struct hsu_port *hsu)
 284 {
 285 }
 286 #endif /* CONFIG_DEBUG_FS */
 287
 288 static void serial_hsu_enable_ms(struct uart_port *port)
 289 {
 290         struct uart_hsu_port *up =
 291                 container_of(port, struct uart_hsu_port, port);
 292
 293         up->ier |= UART_IER_MSI;
 294         serial_out(up, UART_IER, up->ier);
 295 }
 296
 297 void hsu_dma_tx(struct uart_hsu_port *up)
 298 {
 299         struct circ_buf *xmit = &up->port.state->xmit;
 300         struct hsu_dma_buffer *dbuf = &up->txbuf;
 301         int count;
 302
 303         /* test_and_set_bit may be better, but anyway it's in lock protected mode */
 304         if (up->dma_tx_on)
 305                 return;
 306
 307         /* Update the circ buf info */
 308         xmit->tail += dbuf->ofs;
 309         xmit->tail &= UART_XMIT_SIZE - 1;
 310
 311         up->port.icount.tx += dbuf->ofs;
 312         dbuf->ofs = 0;
 313
 314         /* Disable the channel */
 315         chan_writel(up->txc, HSU_CH_CR, 0x0);
 316
 317         if (!uart_circ_empty(xmit) && !uart_tx_stopped(&up->port)) {
 318                 dma_sync_single_for_device(up->port.dev,
 319                                            dbuf->dma_addr,
 320                                            dbuf->dma_size,
 321                                            DMA_TO_DEVICE);
 322
 323                 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
 324                 dbuf->ofs = count;
 325
 326                 /* Reprogram the channel */
 327                 chan_writel(up->txc, HSU_CH_D0SAR, dbuf->dma_addr + xmit->tail);
 328                 chan_writel(up->txc, HSU_CH_D0TSR, count);
 329
 330                 /* Reenable the channel */
 331                 chan_writel(up->txc, HSU_CH_DCR, 0x1
 332                                                  | (0x1 << 8)
 333                                                  | (0x1 << 16)
 334                                                  | (0x1 << 24));
 335                 up->dma_tx_on = 1;
 336                 chan_writel(up->txc, HSU_CH_CR, 0x1);
 337         }
 338
 339         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 340                 uart_write_wakeup(&up->port);
 341 }
 342
 343 /* The buffer is already cache coherent */
 344 void hsu_dma_start_rx_chan(struct hsu_dma_chan *rxc, struct hsu_dma_buffer *dbuf)
 345 {
 346         dbuf->ofs = 0;
 347
 348         chan_writel(rxc, HSU_CH_BSR, 32);
 349         chan_writel(rxc, HSU_CH_MOTSR, 4);
 350
 351         chan_writel(rxc, HSU_CH_D0SAR, dbuf->dma_addr);
 352         chan_writel(rxc, HSU_CH_D0TSR, dbuf->dma_size);
 353         chan_writel(rxc, HSU_CH_DCR, 0x1 | (0x1 << 8)
 354                                          | (0x1 << 16)
 355                                          | (0x1 << 24)  /* timeout bit, see HSU Errata 1 */
 356                                          );
 357         chan_writel(rxc, HSU_CH_CR, 0x3);
 358
 359         mod_timer(&rxc->rx_timer, jiffies + HSU_DMA_TIMEOUT_CHECK_FREQ);
 360 }
 361
 362 /* Protected by spin_lock_irqsave(port->lock) */
 363 static void serial_hsu_start_tx(struct uart_port *port)
 364 {
 365         struct uart_hsu_port *up =
 366                 container_of(port, struct uart_hsu_port, port);
 367
 368         if (up->use_dma) {
 369                 hsu_dma_tx(up);
 370         } else if (!(up->ier & UART_IER_THRI)) {
 371                 up->ier |= UART_IER_THRI;
 372                 serial_out(up, UART_IER, up->ier);
 373         }
 374 }
 375
 376 static void serial_hsu_stop_tx(struct uart_port *port)
 377 {
 378         struct uart_hsu_port *up =
 379                 container_of(port, struct uart_hsu_port, port);
 380         struct hsu_dma_chan *txc = up->txc;
 381
 382         if (up->use_dma)
 383                 chan_writel(txc, HSU_CH_CR, 0x0);
 384         else if (up->ier & UART_IER_THRI) {
 385                 up->ier &= ~UART_IER_THRI;
 386                 serial_out(up, UART_IER, up->ier);
 387         }
 388 }
 389
 390 /* This is always called in spinlock protected mode, so
 391  * modify timeout timer is safe here */
 392 void hsu_dma_rx(struct uart_hsu_port *up, u32 int_sts)
 393 {
 394         struct hsu_dma_buffer *dbuf = &up->rxbuf;
 395         struct hsu_dma_chan *chan = up->rxc;
 396         struct uart_port *port = &up->port;
 397         struct tty_struct *tty = port->state->port.tty;
 398         int count;
 399
 400         if (!tty)
 401                 return;
 402
 403         /*
 404          * First need to know how many is already transferred,
 405          * then check if its a timeout DMA irq, and return
 406          * the trail bytes out, push them up and reenable the
 407          * channel
 408          */
 409
 410         /* Timeout IRQ, need wait some time, see Errata 2 */
 411         if (int_sts & 0xf00)
 412                 udelay(2);
 413
 414         /* Stop the channel */
 415         chan_writel(chan, HSU_CH_CR, 0x0);
 416
 417         count = chan_readl(chan, HSU_CH_D0SAR) - dbuf->dma_addr;
 418         if (!count) {
 419                 /* Restart the channel before we leave */
 420                 chan_writel(chan, HSU_CH_CR, 0x3);
 421                 return;
 422         }
 423         del_timer(&chan->rx_timer);
 424
 425         dma_sync_single_for_cpu(port->dev, dbuf->dma_addr,
 426                         dbuf->dma_size, DMA_FROM_DEVICE);
 427
 428         /*
 429          * Head will only wrap around when we recycle
 430          * the DMA buffer, and when that happens, we
 431          * explicitly set tail to 0. So head will
 432          * always be greater than tail.
 433          */
 434         tty_insert_flip_string(tty, dbuf->buf, count);
 435         port->icount.rx += count;
 436
 437         dma_sync_single_for_device(up->port.dev, dbuf->dma_addr,
 438                         dbuf->dma_size, DMA_FROM_DEVICE);
 439
 440         /* Reprogram the channel */
 441         chan_writel(chan, HSU_CH_D0SAR, dbuf->dma_addr);
 442         chan_writel(chan, HSU_CH_D0TSR, dbuf->dma_size);
 443         chan_writel(chan, HSU_CH_DCR, 0x1
 444                                          | (0x1 << 8)
 445                                          | (0x1 << 16)
 446                                          | (0x1 << 24)  /* timeout bit, see HSU Errata 1 */
 447                                          );
 448         tty_flip_buffer_push(tty);
 449
 450         chan_writel(chan, HSU_CH_CR, 0x3);
 451         chan->rx_timer.expires = jiffies + HSU_DMA_TIMEOUT_CHECK_FREQ;
 452         add_timer(&chan->rx_timer);
 453
 454 }
 455
 456 static void serial_hsu_stop_rx(struct uart_port *port)
 457 {
 458         struct uart_hsu_port *up =
 459                 container_of(port, struct uart_hsu_port, port);
 460         struct hsu_dma_chan *chan = up->rxc;
 461
 462         if (up->use_dma)
 463                 chan_writel(chan, HSU_CH_CR, 0x2);
 464         else {
 465                 up->ier &= ~UART_IER_RLSI;
 466                 up->port.read_status_mask &= ~UART_LSR_DR;
 467                 serial_out(up, UART_IER, up->ier);
 468         }
 469 }
 470
 471 static inline void receive_chars(struct uart_hsu_port *up, int *status)
 472 {
 473         struct tty_struct *tty = up->port.state->port.tty;
 474         unsigned int ch, flag;
 475         unsigned int max_count = 256;
 476
 477         if (!tty)
 478                 return;
 479
 480         do {
 481                 ch = serial_in(up, UART_RX);
 482                 flag = TTY_NORMAL;
 483                 up->port.icount.rx++;
 484
 485                 if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
 486                                        UART_LSR_FE | UART_LSR_OE))) {
 487
 488                         dev_warn(up->dev, "We really rush into ERR/BI case"
 489                                 "status = 0x%02x", *status);
 490                         /* For statistics only */
 491                         if (*status & UART_LSR_BI) {
 492                                 *status &= ~(UART_LSR_FE | UART_LSR_PE);
 493                                 up->port.icount.brk++;
 494                                 /*
 495                                  * We do the SysRQ and SAK checking
 496                                  * here because otherwise the break
 497                                  * may get masked by ignore_status_mask
 498                                  * or read_status_mask.
 499                                  */
 500                                 if (uart_handle_break(&up->port))
 501                                         goto ignore_char;
 502                         } else if (*status & UART_LSR_PE)
 503                                 up->port.icount.parity++;
 504                         else if (*status & UART_LSR_FE)
 505                                 up->port.icount.frame++;
 506                         if (*status & UART_LSR_OE)
 507                                 up->port.icount.overrun++;
 508
 509                         /* Mask off conditions which should be ignored. */
 510                         *status &= up->port.read_status_mask;
 511
 512 #ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE
 513                         if (up->port.cons &&
 514                                 up->port.cons->index == up->port.line) {
 515                                 /* Recover the break flag from console xmit */
 516                                 *status |= up->lsr_break_flag;
 517                                 up->lsr_break_flag = 0;
 518                         }
 519 #endif
 520                         if (*status & UART_LSR_BI) {
 521                                 flag = TTY_BREAK;
 522                         } else if (*status & UART_LSR_PE)
 523                                 flag = TTY_PARITY;
 524                         else if (*status & UART_LSR_FE)
 525                                 flag = TTY_FRAME;
 526                 }
 527
 528                 if (uart_handle_sysrq_char(&up->port, ch))
 529                         goto ignore_char;
 530
 531                 uart_insert_char(&up->port, *status, UART_LSR_OE, ch, flag);
 532         ignore_char:
 533                 *status = serial_in(up, UART_LSR);
 534         } while ((*status & UART_LSR_DR) && max_count--);
 535         tty_flip_buffer_push(tty);
 536 }
 537
 538 static void transmit_chars(struct uart_hsu_port *up)
 539 {
 540         struct circ_buf *xmit = &up->port.state->xmit;
 541         int count;
 542
 543         if (up->port.x_char) {
 544                 serial_out(up, UART_TX, up->port.x_char);
 545                 up->port.icount.tx++;
 546                 up->port.x_char = 0;
 547                 return;
 548         }
 549         if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
 550                 serial_hsu_stop_tx(&up->port);
 551                 return;
 552         }
 553
 554 #ifndef MFD_HSU_A0_STEPPING
 555         count = up->port.fifosize / 2;
 556 #else
 557         /*
 558          * A0 only supports fully empty IRQ, and the first char written
 559          * into it won't clear the EMPT bit, so we may need be cautious
 560          * by useing a shorter buffer
 561          */
 562         count = up->port.fifosize - 4;
 563 #endif
 564         do {
 565                 serial_out(up, UART_TX, xmit->buf[xmit->tail]);
 566                 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 567
 568                 up->port.icount.tx++;
 569                 if (uart_circ_empty(xmit))
 570                         break;
 571         } while (--count > 0);
 572
 573         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 574                 uart_write_wakeup(&up->port);
 575
 576         if (uart_circ_empty(xmit))
 577                 serial_hsu_stop_tx(&up->port);
 578 }
 579
 580 static inline void check_modem_status(struct uart_hsu_port *up)
 581 {
 582         int status;
 583
 584         status = serial_in(up, UART_MSR);
 585
 586         if ((status & UART_MSR_ANY_DELTA) == 0)
 587                 return;
 588
 589         if (status & UART_MSR_TERI)
 590                 up->port.icount.rng++;
 591         if (status & UART_MSR_DDSR)
 592                 up->port.icount.dsr++;
 593         /* We may only get DDCD when HW init and reset */
 594         if (status & UART_MSR_DDCD)
 595                 uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
 596         /* Will start/stop_tx accordingly */
 597         if (status & UART_MSR_DCTS)
 598                 uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
 599
 600         wake_up_interruptible(&up->port.state->port.delta_msr_wait);
 601 }
 602
 603 /*
 604  * This handles the interrupt from one port.
 605  */
 606 static irqreturn_t port_irq(int irq, void *dev_id)
 607 {
 608         struct uart_hsu_port *up = dev_id;
 609         unsigned int iir, lsr;
 610         unsigned long flags;
 611
 612         if (unlikely(!up->running))
 613                 return IRQ_NONE;
 614
 615         spin_lock_irqsave(&up->port.lock, flags);
 616         if (up->use_dma) {
 617                 lsr = serial_in(up, UART_LSR);
 618                 if (unlikely(lsr & (UART_LSR_BI | UART_LSR_PE |
 619                                        UART_LSR_FE | UART_LSR_OE)))
 620                         dev_warn(up->dev,
 621                                 "Got lsr irq while using DMA, lsr = 0x%2x\n",
 622                                 lsr);
 623                 check_modem_status(up);
 624                 spin_unlock_irqrestore(&up->port.lock, flags);
 625                 return IRQ_HANDLED;
 626         }
 627
 628         iir = serial_in(up, UART_IIR);
 629         if (iir & UART_IIR_NO_INT) {
 630                 spin_unlock_irqrestore(&up->port.lock, flags);
 631                 return IRQ_NONE;
 632         }
 633
 634         lsr = serial_in(up, UART_LSR);
 635         if (lsr & UART_LSR_DR)
 636                 receive_chars(up, &lsr);
 637         check_modem_status(up);
 638
 639         /* lsr will be renewed during the receive_chars */
 640         if (lsr & UART_LSR_THRE)
 641                 transmit_chars(up);
 642
 643         spin_unlock_irqrestore(&up->port.lock, flags);
 644         return IRQ_HANDLED;
 645 }
 646
 647 static inline void dma_chan_irq(struct hsu_dma_chan *chan)
 648 {
 649         struct uart_hsu_port *up = chan->uport;
 650         unsigned long flags;
 651         u32 int_sts;
 652
 653         spin_lock_irqsave(&up->port.lock, flags);
 654
 655         if (!up->use_dma || !up->running)
 656                 goto exit;
 657
 658         /*
 659          * No matter what situation, need read clear the IRQ status
 660          * There is a bug, see Errata 5, HSD 2900918
 661          */
 662         int_sts = chan_readl(chan, HSU_CH_SR);
 663
 664         /* Rx channel */
 665         if (chan->dirt == DMA_FROM_DEVICE)
 666                 hsu_dma_rx(up, int_sts);
 667
 668         /* Tx channel */
 669         if (chan->dirt == DMA_TO_DEVICE) {
 670                 chan_writel(chan, HSU_CH_CR, 0x0);
 671                 up->dma_tx_on = 0;
 672                 hsu_dma_tx(up);
 673         }
 674
 675 exit:
 676         spin_unlock_irqrestore(&up->port.lock, flags);
 677         return;
 678 }
 679
 680 static irqreturn_t dma_irq(int irq, void *dev_id)
 681 {
 682         struct hsu_port *hsu = dev_id;
 683         u32 int_sts, i;
 684
 685         int_sts = mfd_readl(hsu, HSU_GBL_DMAISR);
 686
 687         /* Currently we only have 6 channels may be used */
 688         for (i = 0; i < 6; i++) {
 689                 if (int_sts & 0x1)
 690                         dma_chan_irq(&hsu->chans[i]);
 691                 int_sts >>= 1;
 692         }
 693
 694         return IRQ_HANDLED;
 695 }
 696
 697 static unsigned int serial_hsu_tx_empty(struct uart_port *port)
 698 {
 699         struct uart_hsu_port *up =
 700                 container_of(port, struct uart_hsu_port, port);
 701         unsigned long flags;
 702         unsigned int ret;
 703
 704         spin_lock_irqsave(&up->port.lock, flags);
 705         ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
 706         spin_unlock_irqrestore(&up->port.lock, flags);
 707
 708         return ret;
 709 }
 710
 711 static unsigned int serial_hsu_get_mctrl(struct uart_port *port)
 712 {
 713         struct uart_hsu_port *up =
 714                 container_of(port, struct uart_hsu_port, port);
 715         unsigned char status;
 716         unsigned int ret;
 717
 718         status = serial_in(up, UART_MSR);
 719
 720         ret = 0;
 721         if (status & UART_MSR_DCD)
 722                 ret |= TIOCM_CAR;
 723         if (status & UART_MSR_RI)
 724                 ret |= TIOCM_RNG;
 725         if (status & UART_MSR_DSR)
 726                 ret |= TIOCM_DSR;
 727         if (status & UART_MSR_CTS)
 728                 ret |= TIOCM_CTS;
 729         return ret;
 730 }
 731
 732 static void serial_hsu_set_mctrl(struct uart_port *port, unsigned int mctrl)
 733 {
 734         struct uart_hsu_port *up =
 735                 container_of(port, struct uart_hsu_port, port);
 736         unsigned char mcr = 0;
 737
 738         if (mctrl & TIOCM_RTS)
 739                 mcr |= UART_MCR_RTS;
 740         if (mctrl & TIOCM_DTR)
 741                 mcr |= UART_MCR_DTR;
 742         if (mctrl & TIOCM_OUT1)
 743                 mcr |= UART_MCR_OUT1;
 744         if (mctrl & TIOCM_OUT2)
 745                 mcr |= UART_MCR_OUT2;
 746         if (mctrl & TIOCM_LOOP)
 747                 mcr |= UART_MCR_LOOP;
 748
 749         mcr |= up->mcr;
 750
 751         serial_out(up, UART_MCR, mcr);
 752 }
 753
 754 static void serial_hsu_break_ctl(struct uart_port *port, int break_state)
 755 {
 756         struct uart_hsu_port *up =
 757                 container_of(port, struct uart_hsu_port, port);
 758         unsigned long flags;
 759
 760         spin_lock_irqsave(&up->port.lock, flags);
 761         if (break_state == -1)
 762                 up->lcr |= UART_LCR_SBC;
 763         else
 764                 up->lcr &= ~UART_LCR_SBC;
 765         serial_out(up, UART_LCR, up->lcr);
 766         spin_unlock_irqrestore(&up->port.lock, flags);
 767 }
 768
 769 /*
 770  * What special to do:
 771  * 1. chose the 64B fifo mode
 772  * 2. make sure not to select half empty mode for A0 stepping
 773  * 3. start dma or pio depends on configuration
 774  * 4. we only allocate dma memory when needed
 775  */
 776 static int serial_hsu_startup(struct uart_port *port)
 777 {
 778         struct uart_hsu_port *up =
 779                 container_of(port, struct uart_hsu_port, port);
 780         unsigned long flags;
 781
 782         /*
 783          * Clear the FIFO buffers and disable them.
 784          * (they will be reenabled in set_termios())
 785          */
 786         serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
 787         serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
 788                         UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
 789         serial_out(up, UART_FCR, 0);
 790
 791         /* Clear the interrupt registers. */
 792         (void) serial_in(up, UART_LSR);
 793         (void) serial_in(up, UART_RX);
 794         (void) serial_in(up, UART_IIR);
 795         (void) serial_in(up, UART_MSR);
 796
 797         /* Now, initialize the UART, default is 8n1 */
 798         serial_out(up, UART_LCR, UART_LCR_WLEN8);
 799
 800         spin_lock_irqsave(&up->port.lock, flags);
 801
 802         up->port.mctrl |= TIOCM_OUT2;
 803         serial_hsu_set_mctrl(&up->port, up->port.mctrl);
 804
 805         /*
 806          * Finally, enable interrupts.  Note: Modem status interrupts
 807          * are set via set_termios(), which will be occurring imminently
 808          * anyway, so we don't enable them here.
 809          */
 810         if (!up->use_dma)
 811                 up->ier = UART_IER_RLSI | UART_IER_RDI | UART_IER_RTOIE;
 812         else
 813                 up->ier = 0;
 814         serial_out(up, UART_IER, up->ier);
 815
 816         spin_unlock_irqrestore(&up->port.lock, flags);
 817
 818         /* DMA init */
 819         if (up->use_dma) {
 820                 struct hsu_dma_buffer *dbuf;
 821                 struct circ_buf *xmit = &port->state->xmit;
 822
 823                 up->dma_tx_on = 0;
 824
 825                 /* First allocate the RX buffer */
 826                 dbuf = &up->rxbuf;
 827                 dbuf->buf = kzalloc(HSU_DMA_BUF_SIZE, GFP_KERNEL);
 828                 if (!dbuf->buf) {
 829                         up->use_dma = 0;
 830                         goto exit;
 831                 }
 832                 dbuf->dma_addr = dma_map_single(port->dev,
 833                                                 dbuf->buf,
 834                                                 HSU_DMA_BUF_SIZE,
 835                                                 DMA_FROM_DEVICE);
 836                 dbuf->dma_size = HSU_DMA_BUF_SIZE;
 837
 838                 /* Start the RX channel right now */
 839                 hsu_dma_start_rx_chan(up->rxc, dbuf);
 840
 841                 /* Next init the TX DMA */
 842                 dbuf = &up->txbuf;
 843                 dbuf->buf = xmit->buf;
 844                 dbuf->dma_addr = dma_map_single(port->dev,
 845                                                dbuf->buf,
 846                                                UART_XMIT_SIZE,
 847                                                DMA_TO_DEVICE);
 848                 dbuf->dma_size = UART_XMIT_SIZE;
 849
 850                 /* This should not be changed all around */
 851                 chan_writel(up->txc, HSU_CH_BSR, 32);
 852                 chan_writel(up->txc, HSU_CH_MOTSR, 4);
 853                 dbuf->ofs = 0;
 854         }
 855
 856 exit:
 857          /* And clear the interrupt registers again for luck. */
 858         (void) serial_in(up, UART_LSR);
 859         (void) serial_in(up, UART_RX);
 860         (void) serial_in(up, UART_IIR);
 861         (void) serial_in(up, UART_MSR);
 862
 863         up->running = 1;
 864         return 0;
 865 }
 866
 867 static void serial_hsu_shutdown(struct uart_port *port)
 868 {
 869         struct uart_hsu_port *up =
 870                 container_of(port, struct uart_hsu_port, port);
 871         unsigned long flags;
 872
 873         del_timer_sync(&up->rxc->rx_timer);
 874
 875         /* Disable interrupts from this port */
 876         up->ier = 0;
 877         serial_out(up, UART_IER, 0);
 878         up->running = 0;
 879
 880         spin_lock_irqsave(&up->port.lock, flags);
 881         up->port.mctrl &= ~TIOCM_OUT2;
 882         serial_hsu_set_mctrl(&up->port, up->port.mctrl);
 883         spin_unlock_irqrestore(&up->port.lock, flags);
 884
 885         /* Disable break condition and FIFOs */
 886         serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC);
 887         serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
 888                                   UART_FCR_CLEAR_RCVR |
 889                                   UART_FCR_CLEAR_XMIT);
 890         serial_out(up, UART_FCR, 0);
 891 }
 892
 893 static void
 894 serial_hsu_set_termios(struct uart_port *port, struct ktermios *termios,
 895                        struct ktermios *old)
 896 {
 897         struct uart_hsu_port *up =
 898                         container_of(port, struct uart_hsu_port, port);
 899         struct tty_struct *tty = port->state->port.tty;
 900         unsigned char cval, fcr = 0;
 901         unsigned long flags;
 902         unsigned int baud, quot;
 903         u32 ps, mul;
 904
 905         switch (termios->c_cflag & CSIZE) {
 906         case CS5:
 907                 cval = UART_LCR_WLEN5;
 908                 break;
 909         case CS6:
 910                 cval = UART_LCR_WLEN6;
 911                 break;
 912         case CS7:
 913                 cval = UART_LCR_WLEN7;
 914                 break;
 915         default:
 916         case CS8:
 917                 cval = UART_LCR_WLEN8;
 918                 break;
 919         }
 920
 921         /* CMSPAR isn't supported by this driver */
 922         if (tty)
 923                 tty->termios->c_cflag &= ~CMSPAR;
 924
 925         if (termios->c_cflag & CSTOPB)
 926                 cval |= UART_LCR_STOP;
 927         if (termios->c_cflag & PARENB)
 928                 cval |= UART_LCR_PARITY;
 929         if (!(termios->c_cflag & PARODD))
 930                 cval |= UART_LCR_EPAR;
 931
 932         /*
 933          * The base clk is 50Mhz, and the baud rate come from:
 934          *      baud = 50M * MUL / (DIV * PS * DLAB)
 935          *
 936          * For those basic low baud rate we can get the direct
 937          * scalar from 2746800, like 115200 = 2746800/24. For those
 938          * higher baud rate, we handle them case by case, mainly by
 939          * adjusting the MUL/PS registers, and DIV register is kept
 940          * as default value 0x3d09 to make things simple
 941          */
 942         baud = uart_get_baud_rate(port, termios, old, 0, 4000000);
 943
 944         quot = 1;
 945         ps = 0x10;
 946         mul = 0x3600;
 947         switch (baud) {
 948         case 3500000:
 949                 mul = 0x3345;
 950                 ps = 0xC;
 951                 break;
 952         case 1843200:
 953                 mul = 0x2400;
 954                 break;
 955         case 3000000:
 956         case 2500000:
 957         case 2000000:
 958         case 1500000:
 959         case 1000000:
 960         case 500000:
 961                 /* mul/ps/quot = 0x9C4/0x10/0x1 will make a 500000 bps */
 962                 mul = baud / 500000 * 0x9C4;
 963                 break;
 964         default:
 965                 /* Use uart_get_divisor to get quot for other baud rates */
 966                 quot = 0;
 967         }
 968
 969         if (!quot)
 970                 quot = uart_get_divisor(port, baud);
 971
 972         if ((up->port.uartclk / quot) < (2400 * 16))
 973                 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_1B;
 974         else if ((up->port.uartclk / quot) < (230400 * 16))
 975                 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_16B;
 976         else
 977                 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_32B;
 978
 979         fcr |= UART_FCR_HSU_64B_FIFO;
 980 #ifdef MFD_HSU_A0_STEPPING
 981         /* A0 doesn't support half empty IRQ */
 982         fcr |= UART_FCR_FULL_EMPT_TXI;
 983 #endif
 984
 985         /*
 986          * Ok, we're now changing the port state.  Do it with
 987          * interrupts disabled.
 988          */
 989         spin_lock_irqsave(&up->port.lock, flags);
 990
 991         /* Update the per-port timeout */
 992         uart_update_timeout(port, termios->c_cflag, baud);
 993
 994         up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
 995         if (termios->c_iflag & INPCK)
 996                 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
 997         if (termios->c_iflag & (BRKINT | PARMRK))
 998                 up->port.read_status_mask |= UART_LSR_BI;
 999
1000         /* Characters to ignore */
1001         up->port.ignore_status_mask = 0;
1002         if (termios->c_iflag & IGNPAR)
1003                 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
1004         if (termios->c_iflag & IGNBRK) {
1005                 up->port.ignore_status_mask |= UART_LSR_BI;
1006                 /*
1007                  * If we're ignoring parity and break indicators,
1008                  * ignore overruns too (for real raw support).
1009                  */
1010                 if (termios->c_iflag & IGNPAR)
1011                         up->port.ignore_status_mask |= UART_LSR_OE;
1012         }
1013
1014         /* Ignore all characters if CREAD is not set */
1015         if ((termios->c_cflag & CREAD) == 0)
1016                 up->port.ignore_status_mask |= UART_LSR_DR;
1017
1018         /*
1019          * CTS flow control flag and modem status interrupts, disable
1020          * MSI by default
1021          */
1022         up->ier &= ~UART_IER_MSI;
1023         if (UART_ENABLE_MS(&up->port, termios->c_cflag))
1024                 up->ier |= UART_IER_MSI;
1025
1026         serial_out(up, UART_IER, up->ier);
1027
1028         if (termios->c_cflag & CRTSCTS)
1029                 up->mcr |= UART_MCR_AFE | UART_MCR_RTS;
1030         else
1031                 up->mcr &= ~UART_MCR_AFE;
1032
1033         serial_out(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */
1034         serial_out(up, UART_DLL, quot & 0xff);          /* LS of divisor */
1035         serial_out(up, UART_DLM, quot >> 8);            /* MS of divisor */
1036         serial_out(up, UART_LCR, cval);                 /* reset DLAB */
1037         serial_out(up, UART_MUL, mul);                  /* set MUL */
1038         serial_out(up, UART_PS, ps);                    /* set PS */
1039         up->lcr = cval;                                 /* Save LCR */
1040         serial_hsu_set_mctrl(&up->port, up->port.mctrl);
1041         serial_out(up, UART_FCR, fcr);
1042         spin_unlock_irqrestore(&up->port.lock, flags);
1043 }
1044
1045 static void
1046 serial_hsu_pm(struct uart_port *port, unsigned int state,
1047               unsigned int oldstate)
1048 {
1049 }
1050
1051 static void serial_hsu_release_port(struct uart_port *port)
1052 {
1053 }
1054
1055 static int serial_hsu_request_port(struct uart_port *port)
1056 {
1057         return 0;
1058 }
1059
1060 static void serial_hsu_config_port(struct uart_port *port, int flags)
1061 {
1062         struct uart_hsu_port *up =
1063                 container_of(port, struct uart_hsu_port, port);
1064         up->port.type = PORT_MFD;
1065 }
1066
1067 static int
1068 serial_hsu_verify_port(struct uart_port *port, struct serial_struct *ser)
1069 {
1070         /* We don't want the core code to modify any port params */
1071         return -EINVAL;
1072 }
1073
1074 static const char *
1075 serial_hsu_type(struct uart_port *port)
1076 {
1077         struct uart_hsu_port *up =
1078                 container_of(port, struct uart_hsu_port, port);
1079         return up->name;
1080 }
1081
1082 /* Mainly for uart console use */
1083 static struct uart_hsu_port *serial_hsu_ports[3];
1084 static struct uart_driver serial_hsu_reg;
1085
1086 #ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE
1087
1088 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
1089
1090 /* Wait for transmitter & holding register to empty */
1091 static inline void wait_for_xmitr(struct uart_hsu_port *up)
1092 {
1093         unsigned int status, tmout = 1000;
1094
1095         /* Wait up to 1ms for the character to be sent. */
1096         do {
1097                 status = serial_in(up, UART_LSR);
1098
1099                 if (status & UART_LSR_BI)
1100                         up->lsr_break_flag = UART_LSR_BI;
1101
1102                 if (--tmout == 0)
1103                         break;
1104                 udelay(1);
1105         } while (!(status & BOTH_EMPTY));
1106
1107         /* Wait up to 1s for flow control if necessary */
1108         if (up->port.flags & UPF_CONS_FLOW) {
1109                 tmout = 1000000;
1110                 while (--tmout &&
1111                        ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
1112                         udelay(1);
1113         }
1114 }
1115
1116 static void serial_hsu_console_putchar(struct uart_port *port, int ch)
1117 {
1118         struct uart_hsu_port *up =
1119                 container_of(port, struct uart_hsu_port, port);
1120
1121         wait_for_xmitr(up);
1122         serial_out(up, UART_TX, ch);
1123 }
1124
1125 /*
1126  * Print a string to the serial port trying not to disturb
1127  * any possible real use of the port...
1128  *
1129  *      The console_lock must be held when we get here.
1130  */
1131 static void
1132 serial_hsu_console_write(struct console *co, const char *s, unsigned int count)
1133 {
1134         struct uart_hsu_port *up = serial_hsu_ports[co->index];
1135         unsigned long flags;
1136         unsigned int ier;
1137         int locked = 1;
1138
1139         local_irq_save(flags);
1140         if (up->port.sysrq)
1141                 locked = 0;
1142         else if (oops_in_progress) {
1143                 locked = spin_trylock(&up->port.lock);
1144         } else
1145                 spin_lock(&up->port.lock);
1146
1147         /* First save the IER then disable the interrupts */
1148         ier = serial_in(up, UART_IER);
1149         serial_out(up, UART_IER, 0);
1150
1151         uart_console_write(&up->port, s, count, serial_hsu_console_putchar);
1152
1153         /*
1154          * Finally, wait for transmitter to become empty
1155          * and restore the IER
1156          */
1157         wait_for_xmitr(up);
1158         serial_out(up, UART_IER, ier);
1159
1160         if (locked)
1161                 spin_unlock(&up->port.lock);
1162         local_irq_restore(flags);
1163 }
1164
1165 static struct console serial_hsu_console;
1166
1167 static int __init
1168 serial_hsu_console_setup(struct console *co, char *options)
1169 {
1170         struct uart_hsu_port *up;
1171         int baud = 115200;
1172         int bits = 8;
1173         int parity = 'n';
1174         int flow = 'n';
1175         int ret;
1176
1177         if (co->index == -1 || co->index >= serial_hsu_reg.nr)
1178                 co->index = 0;
1179         up = serial_hsu_ports[co->index];
1180         if (!up)
1181                 return -ENODEV;
1182
1183         if (options)
1184                 uart_parse_options(options, &baud, &parity, &bits, &flow);
1185
1186         ret = uart_set_options(&up->port, co, baud, parity, bits, flow);
1187
1188         return ret;
1189 }
1190
1191 static struct console serial_hsu_console = {
1192         .name           = "ttyMFD",
1193         .write          = serial_hsu_console_write,
1194         .device         = uart_console_device,
1195         .setup          = serial_hsu_console_setup,
1196         .flags          = CON_PRINTBUFFER,
1197         .index          = 2,
1198         .data           = &serial_hsu_reg,
1199 };
1200 #endif
1201
1202 struct uart_ops serial_hsu_pops = {
1203         .tx_empty       = serial_hsu_tx_empty,
1204         .set_mctrl      = serial_hsu_set_mctrl,
1205         .get_mctrl      = serial_hsu_get_mctrl,
1206         .stop_tx        = serial_hsu_stop_tx,
1207         .start_tx       = serial_hsu_start_tx,
1208         .stop_rx        = serial_hsu_stop_rx,
1209         .enable_ms      = serial_hsu_enable_ms,
1210         .break_ctl      = serial_hsu_break_ctl,
1211         .startup        = serial_hsu_startup,
1212         .shutdown       = serial_hsu_shutdown,
1213         .set_termios    = serial_hsu_set_termios,
1214         .pm             = serial_hsu_pm,
1215         .type           = serial_hsu_type,
1216         .release_port   = serial_hsu_release_port,
1217         .request_port   = serial_hsu_request_port,
1218         .config_port    = serial_hsu_config_port,
1219         .verify_port    = serial_hsu_verify_port,
1220 };
1221
1222 static struct uart_driver serial_hsu_reg = {
1223         .owner          = THIS_MODULE,
1224         .driver_name    = "MFD serial",
1225         .dev_name       = "ttyMFD",
1226         .major          = TTY_MAJOR,
1227         .minor          = 128,
1228         .nr             = 3,
1229 };
1230
1231 #ifdef CONFIG_PM
1232 static int serial_hsu_suspend(struct pci_dev *pdev, pm_message_t state)
1233 {
1234         void *priv = pci_get_drvdata(pdev);
1235         struct uart_hsu_port *up;
1236
1237         /* Make sure this is not the internal dma controller */
1238         if (priv && (pdev->device != 0x081E)) {
1239                 up = priv;
1240                 uart_suspend_port(&serial_hsu_reg, &up->port);
1241         }
1242
1243         pci_save_state(pdev);
1244         pci_set_power_state(pdev, pci_choose_state(pdev, state));
1245         return 0;
1246 }
1247
1248 static int serial_hsu_resume(struct pci_dev *pdev)
1249 {
1250         void *priv = pci_get_drvdata(pdev);
1251         struct uart_hsu_port *up;
1252         int ret;
1253
1254         pci_set_power_state(pdev, PCI_D0);
1255         pci_restore_state(pdev);
1256
1257         ret = pci_enable_device(pdev);
1258         if (ret)
1259                 dev_warn(&pdev->dev,
1260                         "HSU: can't re-enable device, try to continue\n");
1261
1262         if (priv && (pdev->device != 0x081E)) {
1263                 up = priv;
1264                 uart_resume_port(&serial_hsu_reg, &up->port);
1265         }
1266         return 0;
1267 }
1268 #else
1269 #define serial_hsu_suspend      NULL
1270 #define serial_hsu_resume       NULL
1271 #endif
1272
1273 /* temp global pointer before we settle down on using one or four PCI dev */
1274 static struct hsu_port *phsu;
1275
1276 static int serial_hsu_probe(struct pci_dev *pdev,
1277                                 const struct pci_device_id *ent)
1278 {
1279         struct uart_hsu_port *uport;
1280         int index, ret;
1281
1282         printk(KERN_INFO "HSU: found PCI Serial controller(ID: %04x:%04x)\n",
1283                 pdev->vendor, pdev->device);
1284
1285         switch (pdev->device) {
1286         case 0x081B:
1287                 index = 0;
1288                 break;
1289         case 0x081C:
1290                 index = 1;
1291                 break;
1292         case 0x081D:
1293                 index = 2;
1294                 break;
1295         case 0x081E:
1296                 /* internal DMA controller */
1297                 index = 3;
1298                 break;
1299         default:
1300                 dev_err(&pdev->dev, "HSU: out of index!");
1301                 return -ENODEV;
1302         }
1303
1304         ret = pci_enable_device(pdev);
1305         if (ret)
1306                 return ret;
1307
1308         if (index == 3) {
1309                 /* DMA controller */
1310                 ret = request_irq(pdev->irq, dma_irq, 0, "hsu_dma", phsu);
1311                 if (ret) {
1312                         dev_err(&pdev->dev, "can not get IRQ\n");
1313                         goto err_disable;
1314                 }
1315                 pci_set_drvdata(pdev, phsu);
1316         } else {
1317                 /* UART port 0~2 */
1318                 uport = &phsu->port[index];
1319                 uport->port.irq = pdev->irq;
1320                 uport->port.dev = &pdev->dev;
1321                 uport->dev = &pdev->dev;
1322
1323                 ret = request_irq(pdev->irq, port_irq, 0, uport->name, uport);
1324                 if (ret) {
1325                         dev_err(&pdev->dev, "can not get IRQ\n");
1326                         goto err_disable;
1327                 }
1328                 uart_add_one_port(&serial_hsu_reg, &uport->port);
1329
1330 #ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE
1331                 if (index == 2) {
1332                         register_console(&serial_hsu_console);
1333                         uport->port.cons = &serial_hsu_console;
1334                 }
1335 #endif
1336                 pci_set_drvdata(pdev, uport);
1337         }
1338
1339         return 0;
1340
1341 err_disable:
1342         pci_disable_device(pdev);
1343         return ret;
1344 }
1345
1346 static void hsu_dma_rx_timeout(unsigned long data)
1347 {
1348         struct hsu_dma_chan *chan = (void *)data;
1349         struct uart_hsu_port *up = chan->uport;
1350         struct hsu_dma_buffer *dbuf = &up->rxbuf;
1351         int count = 0;
1352         unsigned long flags;
1353
1354         spin_lock_irqsave(&up->port.lock, flags);
1355
1356         count = chan_readl(chan, HSU_CH_D0SAR) - dbuf->dma_addr;
1357
1358         if (!count) {
1359                 mod_timer(&chan->rx_timer, jiffies + HSU_DMA_TIMEOUT_CHECK_FREQ);
1360                 goto exit;
1361         }
1362
1363         hsu_dma_rx(up, 0);
1364 exit:
1365         spin_unlock_irqrestore(&up->port.lock, flags);
1366 }
1367
1368 static void hsu_global_init(void)
1369 {
1370         struct hsu_port *hsu;
1371         struct uart_hsu_port *uport;
1372         struct hsu_dma_chan *dchan;
1373         int i, ret;
1374
1375         hsu = kzalloc(sizeof(struct hsu_port), GFP_KERNEL);
1376         if (!hsu)
1377                 return;
1378
1379         /* Get basic io resource and map it */
1380         hsu->paddr = 0xffa28000;
1381         hsu->iolen = 0x1000;
1382
1383         if (!(request_mem_region(hsu->paddr, hsu->iolen, "HSU global")))
1384                 pr_warning("HSU: error in request mem region\n");
1385
1386         hsu->reg = ioremap_nocache((unsigned long)hsu->paddr, hsu->iolen);
1387         if (!hsu->reg) {
1388                 pr_err("HSU: error in ioremap\n");
1389                 ret = -ENOMEM;
1390                 goto err_free_region;
1391         }
1392
1393         /* Initialise the 3 UART ports */
1394         uport = hsu->port;
1395         for (i = 0; i < 3; i++) {
1396                 uport->port.type = PORT_MFD;
1397                 uport->port.iotype = UPIO_MEM;
1398                 uport->port.mapbase = (resource_size_t)hsu->paddr
1399                                         + HSU_PORT_REG_OFFSET
1400                                         + i * HSU_PORT_REG_LENGTH;
1401                 uport->port.membase = hsu->reg + HSU_PORT_REG_OFFSET
1402                                         + i * HSU_PORT_REG_LENGTH;
1403
1404                 sprintf(uport->name, "hsu_port%d", i);
1405                 uport->port.fifosize = 64;
1406                 uport->port.ops = &serial_hsu_pops;
1407                 uport->port.line = i;
1408                 uport->port.flags = UPF_IOREMAP;
1409                 /* set the scalable maxim support rate to 2746800 bps */
1410                 uport->port.uartclk = 115200 * 24 * 16;
1411
1412                 uport->running = 0;
1413                 uport->txc = &hsu->chans[i * 2];
1414                 uport->rxc = &hsu->chans[i * 2 + 1];
1415
1416                 serial_hsu_ports[i] = uport;
1417                 uport->index = i;
1418                 uport++;
1419         }
1420
1421         /* Initialise 6 dma channels */
1422         dchan = hsu->chans;
1423         for (i = 0; i < 6; i++) {
1424                 dchan->id = i;
1425                 dchan->dirt = (i & 0x1) ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
1426                 dchan->uport = &hsu->port[i/2];
1427                 dchan->reg = hsu->reg + HSU_DMA_CHANS_REG_OFFSET +
1428                                 i * HSU_DMA_CHANS_REG_LENGTH;
1429
1430                 /* Work around for RX */
1431                 if (dchan->dirt == DMA_FROM_DEVICE) {
1432                         init_timer(&dchan->rx_timer);
1433                         dchan->rx_timer.function = hsu_dma_rx_timeout;
1434                         dchan->rx_timer.data = (unsigned long)dchan;
1435                 }
1436                 dchan++;
1437         }
1438
1439         phsu = hsu;
1440         hsu_debugfs_init(hsu);
1441         return;
1442
1443 err_free_region:
1444         release_mem_region(hsu->paddr, hsu->iolen);
1445         kfree(hsu);
1446         return;
1447 }
1448
1449 static void serial_hsu_remove(struct pci_dev *pdev)
1450 {
1451         void *priv = pci_get_drvdata(pdev);
1452         struct uart_hsu_port *up;
1453
1454         if (!priv)
1455                 return;
1456
1457         /* For port 0/1/2, priv is the address of uart_hsu_port */
1458         if (pdev->device != 0x081E) {
1459                 up = priv;
1460                 uart_remove_one_port(&serial_hsu_reg, &up->port);
1461         }
1462
1463         pci_set_drvdata(pdev, NULL);
1464         free_irq(pdev->irq, priv);
1465         pci_disable_device(pdev);
1466 }
1467
1468 /* First 3 are UART ports, and the 4th is the DMA */
1469 static const struct pci_device_id pci_ids[] __devinitdata = {
1470         { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081B) },
1471         { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081C) },
1472         { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081D) },
1473         { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081E) },
1474         {},
1475 };
1476
1477 static struct pci_driver hsu_pci_driver = {
1478         .name =         "HSU serial",
1479         .id_table =     pci_ids,
1480         .probe =        serial_hsu_probe,
1481         .remove =       __devexit_p(serial_hsu_remove),
1482         .suspend =      serial_hsu_suspend,
1483         .resume =       serial_hsu_resume,
1484 };
1485
1486 static int __init hsu_pci_init(void)
1487 {
1488         int ret;
1489
1490         hsu_global_init();
1491
1492         ret = uart_register_driver(&serial_hsu_reg);
1493         if (ret)
1494                 return ret;
1495
1496         return pci_register_driver(&hsu_pci_driver);
1497 }
1498
1499 static void __exit hsu_pci_exit(void)
1500 {
1501         pci_unregister_driver(&hsu_pci_driver);
1502         uart_unregister_driver(&serial_hsu_reg);
1503
1504         hsu_debugfs_remove(phsu);
1505
1506         kfree(phsu);
1507 }
1508
1509 module_init(hsu_pci_init);
1510 module_exit(hsu_pci_exit);
1511
1512 MODULE_LICENSE("GPL v2");
1513 MODULE_ALIAS("platform:medfield-hsu");