media: ov5640: Add Omnivision OV5640 support
[linux-2.6.git] / drivers / tty / mxser.c
1 /*
2  *          mxser.c  -- MOXA Smartio/Industio family multiport serial driver.
3  *
4  *      Copyright (C) 1999-2006  Moxa Technologies (support@moxa.com).
5  *      Copyright (C) 2006-2008  Jiri Slaby <jirislaby@gmail.com>
6  *
7  *      This code is loosely based on the 1.8 moxa driver which is based on
8  *      Linux serial driver, written by Linus Torvalds, Theodore T'so and
9  *      others.
10  *
11  *      This program is free software; you can redistribute it and/or modify
12  *      it under the terms of the GNU General Public License as published by
13  *      the Free Software Foundation; either version 2 of the License, or
14  *      (at your option) any later version.
15  *
16  *      Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox
17  *      <alan@lxorguk.ukuu.org.uk>. The original 1.8 code is available on
18  *      www.moxa.com.
19  *      - Fixed x86_64 cleanness
20  */
21
22 #include <linux/module.h>
23 #include <linux/errno.h>
24 #include <linux/signal.h>
25 #include <linux/sched.h>
26 #include <linux/timer.h>
27 #include <linux/interrupt.h>
28 #include <linux/tty.h>
29 #include <linux/tty_flip.h>
30 #include <linux/serial.h>
31 #include <linux/serial_reg.h>
32 #include <linux/major.h>
33 #include <linux/string.h>
34 #include <linux/fcntl.h>
35 #include <linux/ptrace.h>
36 #include <linux/ioport.h>
37 #include <linux/mm.h>
38 #include <linux/delay.h>
39 #include <linux/pci.h>
40 #include <linux/bitops.h>
41 #include <linux/slab.h>
42 #include <linux/ratelimit.h>
43
44 #include <asm/system.h>
45 #include <asm/io.h>
46 #include <asm/irq.h>
47 #include <asm/uaccess.h>
48
49 #include "mxser.h"
50
51 #define MXSER_VERSION   "2.0.5"         /* 1.14 */
52 #define MXSERMAJOR       174
53
54 #define MXSER_BOARDS            4       /* Max. boards */
55 #define MXSER_PORTS_PER_BOARD   8       /* Max. ports per board */
56 #define MXSER_PORTS             (MXSER_BOARDS * MXSER_PORTS_PER_BOARD)
57 #define MXSER_ISR_PASS_LIMIT    100
58
59 /*CheckIsMoxaMust return value*/
60 #define MOXA_OTHER_UART         0x00
61 #define MOXA_MUST_MU150_HWID    0x01
62 #define MOXA_MUST_MU860_HWID    0x02
63
64 #define WAKEUP_CHARS            256
65
66 #define UART_MCR_AFE            0x20
67 #define UART_LSR_SPECIAL        0x1E
68
69 #define PCI_DEVICE_ID_POS104UL  0x1044
70 #define PCI_DEVICE_ID_CB108     0x1080
71 #define PCI_DEVICE_ID_CP102UF   0x1023
72 #define PCI_DEVICE_ID_CP112UL   0x1120
73 #define PCI_DEVICE_ID_CB114     0x1142
74 #define PCI_DEVICE_ID_CP114UL   0x1143
75 #define PCI_DEVICE_ID_CB134I    0x1341
76 #define PCI_DEVICE_ID_CP138U    0x1380
77
78
79 #define C168_ASIC_ID    1
80 #define C104_ASIC_ID    2
81 #define C102_ASIC_ID    0xB
82 #define CI132_ASIC_ID   4
83 #define CI134_ASIC_ID   3
84 #define CI104J_ASIC_ID  5
85
86 #define MXSER_HIGHBAUD  1
87 #define MXSER_HAS2      2
88
89 /* This is only for PCI */
90 static const struct {
91         int type;
92         int tx_fifo;
93         int rx_fifo;
94         int xmit_fifo_size;
95         int rx_high_water;
96         int rx_trigger;
97         int rx_low_water;
98         long max_baud;
99 } Gpci_uart_info[] = {
100         {MOXA_OTHER_UART, 16, 16, 16, 14, 14, 1, 921600L},
101         {MOXA_MUST_MU150_HWID, 64, 64, 64, 48, 48, 16, 230400L},
102         {MOXA_MUST_MU860_HWID, 128, 128, 128, 96, 96, 32, 921600L}
103 };
104 #define UART_INFO_NUM   ARRAY_SIZE(Gpci_uart_info)
105
106 struct mxser_cardinfo {
107         char *name;
108         unsigned int nports;
109         unsigned int flags;
110 };
111
112 static const struct mxser_cardinfo mxser_cards[] = {
113 /* 0*/  { "C168 series",        8, },
114         { "C104 series",        4, },
115         { "CI-104J series",     4, },
116         { "C168H/PCI series",   8, },
117         { "C104H/PCI series",   4, },
118 /* 5*/  { "C102 series",        4, MXSER_HAS2 },        /* C102-ISA */
119         { "CI-132 series",      4, MXSER_HAS2 },
120         { "CI-134 series",      4, },
121         { "CP-132 series",      2, },
122         { "CP-114 series",      4, },
123 /*10*/  { "CT-114 series",      4, },
124         { "CP-102 series",      2, MXSER_HIGHBAUD },
125         { "CP-104U series",     4, },
126         { "CP-168U series",     8, },
127         { "CP-132U series",     2, },
128 /*15*/  { "CP-134U series",     4, },
129         { "CP-104JU series",    4, },
130         { "Moxa UC7000 Serial", 8, },           /* RC7000 */
131         { "CP-118U series",     8, },
132         { "CP-102UL series",    2, },
133 /*20*/  { "CP-102U series",     2, },
134         { "CP-118EL series",    8, },
135         { "CP-168EL series",    8, },
136         { "CP-104EL series",    4, },
137         { "CB-108 series",      8, },
138 /*25*/  { "CB-114 series",      4, },
139         { "CB-134I series",     4, },
140         { "CP-138U series",     8, },
141         { "POS-104UL series",   4, },
142         { "CP-114UL series",    4, },
143 /*30*/  { "CP-102UF series",    2, },
144         { "CP-112UL series",    2, },
145 };
146
147 /* driver_data correspond to the lines in the structure above
148    see also ISA probe function before you change something */
149 static struct pci_device_id mxser_pcibrds[] = {
150         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C168),   .driver_data = 3 },
151         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C104),   .driver_data = 4 },
152         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132),  .driver_data = 8 },
153         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP114),  .driver_data = 9 },
154         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CT114),  .driver_data = 10 },
155         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102),  .driver_data = 11 },
156         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104U), .driver_data = 12 },
157         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168U), .driver_data = 13 },
158         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132U), .driver_data = 14 },
159         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP134U), .driver_data = 15 },
160         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104JU),.driver_data = 16 },
161         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_RC7000), .driver_data = 17 },
162         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118U), .driver_data = 18 },
163         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102UL),.driver_data = 19 },
164         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102U), .driver_data = 20 },
165         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118EL),.driver_data = 21 },
166         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168EL),.driver_data = 22 },
167         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104EL),.driver_data = 23 },
168         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB108),       .driver_data = 24 },
169         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB114),       .driver_data = 25 },
170         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB134I),      .driver_data = 26 },
171         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP138U),      .driver_data = 27 },
172         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_POS104UL),    .driver_data = 28 },
173         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP114UL),     .driver_data = 29 },
174         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP102UF),     .driver_data = 30 },
175         { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP112UL),     .driver_data = 31 },
176         { }
177 };
178 MODULE_DEVICE_TABLE(pci, mxser_pcibrds);
179
180 static unsigned long ioaddr[MXSER_BOARDS];
181 static int ttymajor = MXSERMAJOR;
182
183 /* Variables for insmod */
184
185 MODULE_AUTHOR("Casper Yang");
186 MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver");
187 module_param_array(ioaddr, ulong, NULL, 0);
188 MODULE_PARM_DESC(ioaddr, "ISA io addresses to look for a moxa board");
189 module_param(ttymajor, int, 0);
190 MODULE_LICENSE("GPL");
191
192 struct mxser_log {
193         int tick;
194         unsigned long rxcnt[MXSER_PORTS];
195         unsigned long txcnt[MXSER_PORTS];
196 };
197
198 struct mxser_mon {
199         unsigned long rxcnt;
200         unsigned long txcnt;
201         unsigned long up_rxcnt;
202         unsigned long up_txcnt;
203         int modem_status;
204         unsigned char hold_reason;
205 };
206
207 struct mxser_mon_ext {
208         unsigned long rx_cnt[32];
209         unsigned long tx_cnt[32];
210         unsigned long up_rxcnt[32];
211         unsigned long up_txcnt[32];
212         int modem_status[32];
213
214         long baudrate[32];
215         int databits[32];
216         int stopbits[32];
217         int parity[32];
218         int flowctrl[32];
219         int fifo[32];
220         int iftype[32];
221 };
222
223 struct mxser_board;
224
225 struct mxser_port {
226         struct tty_port port;
227         struct mxser_board *board;
228
229         unsigned long ioaddr;
230         unsigned long opmode_ioaddr;
231         int max_baud;
232
233         int rx_high_water;
234         int rx_trigger;         /* Rx fifo trigger level */
235         int rx_low_water;
236         int baud_base;          /* max. speed */
237         int type;               /* UART type */
238
239         int x_char;             /* xon/xoff character */
240         int IER;                /* Interrupt Enable Register */
241         int MCR;                /* Modem control register */
242
243         unsigned char stop_rx;
244         unsigned char ldisc_stop_rx;
245
246         int custom_divisor;
247         unsigned char err_shadow;
248
249         struct async_icount icount; /* kernel counters for 4 input interrupts */
250         int timeout;
251
252         int read_status_mask;
253         int ignore_status_mask;
254         int xmit_fifo_size;
255         int xmit_head;
256         int xmit_tail;
257         int xmit_cnt;
258
259         struct ktermios normal_termios;
260
261         struct mxser_mon mon_data;
262
263         spinlock_t slock;
264 };
265
266 struct mxser_board {
267         unsigned int idx;
268         int irq;
269         const struct mxser_cardinfo *info;
270         unsigned long vector;
271         unsigned long vector_mask;
272
273         int chip_flag;
274         int uart_type;
275
276         struct mxser_port ports[MXSER_PORTS_PER_BOARD];
277 };
278
279 struct mxser_mstatus {
280         tcflag_t cflag;
281         int cts;
282         int dsr;
283         int ri;
284         int dcd;
285 };
286
287 static struct mxser_board mxser_boards[MXSER_BOARDS];
288 static struct tty_driver *mxvar_sdriver;
289 static struct mxser_log mxvar_log;
290 static int mxser_set_baud_method[MXSER_PORTS + 1];
291
292 static void mxser_enable_must_enchance_mode(unsigned long baseio)
293 {
294         u8 oldlcr;
295         u8 efr;
296
297         oldlcr = inb(baseio + UART_LCR);
298         outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
299
300         efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
301         efr |= MOXA_MUST_EFR_EFRB_ENABLE;
302
303         outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
304         outb(oldlcr, baseio + UART_LCR);
305 }
306
307 #ifdef  CONFIG_PCI
308 static void mxser_disable_must_enchance_mode(unsigned long baseio)
309 {
310         u8 oldlcr;
311         u8 efr;
312
313         oldlcr = inb(baseio + UART_LCR);
314         outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
315
316         efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
317         efr &= ~MOXA_MUST_EFR_EFRB_ENABLE;
318
319         outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
320         outb(oldlcr, baseio + UART_LCR);
321 }
322 #endif
323
324 static void mxser_set_must_xon1_value(unsigned long baseio, u8 value)
325 {
326         u8 oldlcr;
327         u8 efr;
328
329         oldlcr = inb(baseio + UART_LCR);
330         outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
331
332         efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
333         efr &= ~MOXA_MUST_EFR_BANK_MASK;
334         efr |= MOXA_MUST_EFR_BANK0;
335
336         outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
337         outb(value, baseio + MOXA_MUST_XON1_REGISTER);
338         outb(oldlcr, baseio + UART_LCR);
339 }
340
341 static void mxser_set_must_xoff1_value(unsigned long baseio, u8 value)
342 {
343         u8 oldlcr;
344         u8 efr;
345
346         oldlcr = inb(baseio + UART_LCR);
347         outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
348
349         efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
350         efr &= ~MOXA_MUST_EFR_BANK_MASK;
351         efr |= MOXA_MUST_EFR_BANK0;
352
353         outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
354         outb(value, baseio + MOXA_MUST_XOFF1_REGISTER);
355         outb(oldlcr, baseio + UART_LCR);
356 }
357
358 static void mxser_set_must_fifo_value(struct mxser_port *info)
359 {
360         u8 oldlcr;
361         u8 efr;
362
363         oldlcr = inb(info->ioaddr + UART_LCR);
364         outb(MOXA_MUST_ENTER_ENCHANCE, info->ioaddr + UART_LCR);
365
366         efr = inb(info->ioaddr + MOXA_MUST_EFR_REGISTER);
367         efr &= ~MOXA_MUST_EFR_BANK_MASK;
368         efr |= MOXA_MUST_EFR_BANK1;
369
370         outb(efr, info->ioaddr + MOXA_MUST_EFR_REGISTER);
371         outb((u8)info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTH_REGISTER);
372         outb((u8)info->rx_trigger, info->ioaddr + MOXA_MUST_RBRTI_REGISTER);
373         outb((u8)info->rx_low_water, info->ioaddr + MOXA_MUST_RBRTL_REGISTER);
374         outb(oldlcr, info->ioaddr + UART_LCR);
375 }
376
377 static void mxser_set_must_enum_value(unsigned long baseio, u8 value)
378 {
379         u8 oldlcr;
380         u8 efr;
381
382         oldlcr = inb(baseio + UART_LCR);
383         outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
384
385         efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
386         efr &= ~MOXA_MUST_EFR_BANK_MASK;
387         efr |= MOXA_MUST_EFR_BANK2;
388
389         outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
390         outb(value, baseio + MOXA_MUST_ENUM_REGISTER);
391         outb(oldlcr, baseio + UART_LCR);
392 }
393
394 #ifdef CONFIG_PCI
395 static void mxser_get_must_hardware_id(unsigned long baseio, u8 *pId)
396 {
397         u8 oldlcr;
398         u8 efr;
399
400         oldlcr = inb(baseio + UART_LCR);
401         outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
402
403         efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
404         efr &= ~MOXA_MUST_EFR_BANK_MASK;
405         efr |= MOXA_MUST_EFR_BANK2;
406
407         outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
408         *pId = inb(baseio + MOXA_MUST_HWID_REGISTER);
409         outb(oldlcr, baseio + UART_LCR);
410 }
411 #endif
412
413 static void SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(unsigned long baseio)
414 {
415         u8 oldlcr;
416         u8 efr;
417
418         oldlcr = inb(baseio + UART_LCR);
419         outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
420
421         efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
422         efr &= ~MOXA_MUST_EFR_SF_MASK;
423
424         outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
425         outb(oldlcr, baseio + UART_LCR);
426 }
427
428 static void mxser_enable_must_tx_software_flow_control(unsigned long baseio)
429 {
430         u8 oldlcr;
431         u8 efr;
432
433         oldlcr = inb(baseio + UART_LCR);
434         outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
435
436         efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
437         efr &= ~MOXA_MUST_EFR_SF_TX_MASK;
438         efr |= MOXA_MUST_EFR_SF_TX1;
439
440         outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
441         outb(oldlcr, baseio + UART_LCR);
442 }
443
444 static void mxser_disable_must_tx_software_flow_control(unsigned long baseio)
445 {
446         u8 oldlcr;
447         u8 efr;
448
449         oldlcr = inb(baseio + UART_LCR);
450         outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
451
452         efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
453         efr &= ~MOXA_MUST_EFR_SF_TX_MASK;
454
455         outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
456         outb(oldlcr, baseio + UART_LCR);
457 }
458
459 static void mxser_enable_must_rx_software_flow_control(unsigned long baseio)
460 {
461         u8 oldlcr;
462         u8 efr;
463
464         oldlcr = inb(baseio + UART_LCR);
465         outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
466
467         efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
468         efr &= ~MOXA_MUST_EFR_SF_RX_MASK;
469         efr |= MOXA_MUST_EFR_SF_RX1;
470
471         outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
472         outb(oldlcr, baseio + UART_LCR);
473 }
474
475 static void mxser_disable_must_rx_software_flow_control(unsigned long baseio)
476 {
477         u8 oldlcr;
478         u8 efr;
479
480         oldlcr = inb(baseio + UART_LCR);
481         outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
482
483         efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
484         efr &= ~MOXA_MUST_EFR_SF_RX_MASK;
485
486         outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
487         outb(oldlcr, baseio + UART_LCR);
488 }
489
490 #ifdef CONFIG_PCI
491 static int __devinit CheckIsMoxaMust(unsigned long io)
492 {
493         u8 oldmcr, hwid;
494         int i;
495
496         outb(0, io + UART_LCR);
497         mxser_disable_must_enchance_mode(io);
498         oldmcr = inb(io + UART_MCR);
499         outb(0, io + UART_MCR);
500         mxser_set_must_xon1_value(io, 0x11);
501         if ((hwid = inb(io + UART_MCR)) != 0) {
502                 outb(oldmcr, io + UART_MCR);
503                 return MOXA_OTHER_UART;
504         }
505
506         mxser_get_must_hardware_id(io, &hwid);
507         for (i = 1; i < UART_INFO_NUM; i++) { /* 0 = OTHER_UART */
508                 if (hwid == Gpci_uart_info[i].type)
509                         return (int)hwid;
510         }
511         return MOXA_OTHER_UART;
512 }
513 #endif
514
515 static void process_txrx_fifo(struct mxser_port *info)
516 {
517         int i;
518
519         if ((info->type == PORT_16450) || (info->type == PORT_8250)) {
520                 info->rx_trigger = 1;
521                 info->rx_high_water = 1;
522                 info->rx_low_water = 1;
523                 info->xmit_fifo_size = 1;
524         } else
525                 for (i = 0; i < UART_INFO_NUM; i++)
526                         if (info->board->chip_flag == Gpci_uart_info[i].type) {
527                                 info->rx_trigger = Gpci_uart_info[i].rx_trigger;
528                                 info->rx_low_water = Gpci_uart_info[i].rx_low_water;
529                                 info->rx_high_water = Gpci_uart_info[i].rx_high_water;
530                                 info->xmit_fifo_size = Gpci_uart_info[i].xmit_fifo_size;
531                                 break;
532                         }
533 }
534
535 static unsigned char mxser_get_msr(int baseaddr, int mode, int port)
536 {
537         static unsigned char mxser_msr[MXSER_PORTS + 1];
538         unsigned char status = 0;
539
540         status = inb(baseaddr + UART_MSR);
541
542         mxser_msr[port] &= 0x0F;
543         mxser_msr[port] |= status;
544         status = mxser_msr[port];
545         if (mode)
546                 mxser_msr[port] = 0;
547
548         return status;
549 }
550
551 static int mxser_carrier_raised(struct tty_port *port)
552 {
553         struct mxser_port *mp = container_of(port, struct mxser_port, port);
554         return (inb(mp->ioaddr + UART_MSR) & UART_MSR_DCD)?1:0;
555 }
556
557 static void mxser_dtr_rts(struct tty_port *port, int on)
558 {
559         struct mxser_port *mp = container_of(port, struct mxser_port, port);
560         unsigned long flags;
561
562         spin_lock_irqsave(&mp->slock, flags);
563         if (on)
564                 outb(inb(mp->ioaddr + UART_MCR) |
565                         UART_MCR_DTR | UART_MCR_RTS, mp->ioaddr + UART_MCR);
566         else
567                 outb(inb(mp->ioaddr + UART_MCR)&~(UART_MCR_DTR | UART_MCR_RTS),
568                         mp->ioaddr + UART_MCR);
569         spin_unlock_irqrestore(&mp->slock, flags);
570 }
571
572 static int mxser_set_baud(struct tty_struct *tty, long newspd)
573 {
574         struct mxser_port *info = tty->driver_data;
575         int quot = 0, baud;
576         unsigned char cval;
577
578         if (!info->ioaddr)
579                 return -1;
580
581         if (newspd > info->max_baud)
582                 return -1;
583
584         if (newspd == 134) {
585                 quot = 2 * info->baud_base / 269;
586                 tty_encode_baud_rate(tty, 134, 134);
587         } else if (newspd) {
588                 quot = info->baud_base / newspd;
589                 if (quot == 0)
590                         quot = 1;
591                 baud = info->baud_base/quot;
592                 tty_encode_baud_rate(tty, baud, baud);
593         } else {
594                 quot = 0;
595         }
596
597         info->timeout = ((info->xmit_fifo_size * HZ * 10 * quot) / info->baud_base);
598         info->timeout += HZ / 50;       /* Add .02 seconds of slop */
599
600         if (quot) {
601                 info->MCR |= UART_MCR_DTR;
602                 outb(info->MCR, info->ioaddr + UART_MCR);
603         } else {
604                 info->MCR &= ~UART_MCR_DTR;
605                 outb(info->MCR, info->ioaddr + UART_MCR);
606                 return 0;
607         }
608
609         cval = inb(info->ioaddr + UART_LCR);
610
611         outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR);    /* set DLAB */
612
613         outb(quot & 0xff, info->ioaddr + UART_DLL);     /* LS of divisor */
614         outb(quot >> 8, info->ioaddr + UART_DLM);       /* MS of divisor */
615         outb(cval, info->ioaddr + UART_LCR);    /* reset DLAB */
616
617 #ifdef BOTHER
618         if (C_BAUD(tty) == BOTHER) {
619                 quot = info->baud_base % newspd;
620                 quot *= 8;
621                 if (quot % newspd > newspd / 2) {
622                         quot /= newspd;
623                         quot++;
624                 } else
625                         quot /= newspd;
626
627                 mxser_set_must_enum_value(info->ioaddr, quot);
628         } else
629 #endif
630                 mxser_set_must_enum_value(info->ioaddr, 0);
631
632         return 0;
633 }
634
635 /*
636  * This routine is called to set the UART divisor registers to match
637  * the specified baud rate for a serial port.
638  */
639 static int mxser_change_speed(struct tty_struct *tty,
640                                         struct ktermios *old_termios)
641 {
642         struct mxser_port *info = tty->driver_data;
643         unsigned cflag, cval, fcr;
644         int ret = 0;
645         unsigned char status;
646
647         cflag = tty->termios->c_cflag;
648         if (!info->ioaddr)
649                 return ret;
650
651         if (mxser_set_baud_method[tty->index] == 0)
652                 mxser_set_baud(tty, tty_get_baud_rate(tty));
653
654         /* byte size and parity */
655         switch (cflag & CSIZE) {
656         case CS5:
657                 cval = 0x00;
658                 break;
659         case CS6:
660                 cval = 0x01;
661                 break;
662         case CS7:
663                 cval = 0x02;
664                 break;
665         case CS8:
666                 cval = 0x03;
667                 break;
668         default:
669                 cval = 0x00;
670                 break;          /* too keep GCC shut... */
671         }
672         if (cflag & CSTOPB)
673                 cval |= 0x04;
674         if (cflag & PARENB)
675                 cval |= UART_LCR_PARITY;
676         if (!(cflag & PARODD))
677                 cval |= UART_LCR_EPAR;
678         if (cflag & CMSPAR)
679                 cval |= UART_LCR_SPAR;
680
681         if ((info->type == PORT_8250) || (info->type == PORT_16450)) {
682                 if (info->board->chip_flag) {
683                         fcr = UART_FCR_ENABLE_FIFO;
684                         fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
685                         mxser_set_must_fifo_value(info);
686                 } else
687                         fcr = 0;
688         } else {
689                 fcr = UART_FCR_ENABLE_FIFO;
690                 if (info->board->chip_flag) {
691                         fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
692                         mxser_set_must_fifo_value(info);
693                 } else {
694                         switch (info->rx_trigger) {
695                         case 1:
696                                 fcr |= UART_FCR_TRIGGER_1;
697                                 break;
698                         case 4:
699                                 fcr |= UART_FCR_TRIGGER_4;
700                                 break;
701                         case 8:
702                                 fcr |= UART_FCR_TRIGGER_8;
703                                 break;
704                         default:
705                                 fcr |= UART_FCR_TRIGGER_14;
706                                 break;
707                         }
708                 }
709         }
710
711         /* CTS flow control flag and modem status interrupts */
712         info->IER &= ~UART_IER_MSI;
713         info->MCR &= ~UART_MCR_AFE;
714         if (cflag & CRTSCTS) {
715                 info->port.flags |= ASYNC_CTS_FLOW;
716                 info->IER |= UART_IER_MSI;
717                 if ((info->type == PORT_16550A) || (info->board->chip_flag)) {
718                         info->MCR |= UART_MCR_AFE;
719                 } else {
720                         status = inb(info->ioaddr + UART_MSR);
721                         if (tty->hw_stopped) {
722                                 if (status & UART_MSR_CTS) {
723                                         tty->hw_stopped = 0;
724                                         if (info->type != PORT_16550A &&
725                                                         !info->board->chip_flag) {
726                                                 outb(info->IER & ~UART_IER_THRI,
727                                                         info->ioaddr +
728                                                         UART_IER);
729                                                 info->IER |= UART_IER_THRI;
730                                                 outb(info->IER, info->ioaddr +
731                                                                 UART_IER);
732                                         }
733                                         tty_wakeup(tty);
734                                 }
735                         } else {
736                                 if (!(status & UART_MSR_CTS)) {
737                                         tty->hw_stopped = 1;
738                                         if ((info->type != PORT_16550A) &&
739                                                         (!info->board->chip_flag)) {
740                                                 info->IER &= ~UART_IER_THRI;
741                                                 outb(info->IER, info->ioaddr +
742                                                                 UART_IER);
743                                         }
744                                 }
745                         }
746                 }
747         } else {
748                 info->port.flags &= ~ASYNC_CTS_FLOW;
749         }
750         outb(info->MCR, info->ioaddr + UART_MCR);
751         if (cflag & CLOCAL) {
752                 info->port.flags &= ~ASYNC_CHECK_CD;
753         } else {
754                 info->port.flags |= ASYNC_CHECK_CD;
755                 info->IER |= UART_IER_MSI;
756         }
757         outb(info->IER, info->ioaddr + UART_IER);
758
759         /*
760          * Set up parity check flag
761          */
762         info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
763         if (I_INPCK(tty))
764                 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
765         if (I_BRKINT(tty) || I_PARMRK(tty))
766                 info->read_status_mask |= UART_LSR_BI;
767
768         info->ignore_status_mask = 0;
769
770         if (I_IGNBRK(tty)) {
771                 info->ignore_status_mask |= UART_LSR_BI;
772                 info->read_status_mask |= UART_LSR_BI;
773                 /*
774                  * If we're ignore parity and break indicators, ignore
775                  * overruns too.  (For real raw support).
776                  */
777                 if (I_IGNPAR(tty)) {
778                         info->ignore_status_mask |=
779                                                 UART_LSR_OE |
780                                                 UART_LSR_PE |
781                                                 UART_LSR_FE;
782                         info->read_status_mask |=
783                                                 UART_LSR_OE |
784                                                 UART_LSR_PE |
785                                                 UART_LSR_FE;
786                 }
787         }
788         if (info->board->chip_flag) {
789                 mxser_set_must_xon1_value(info->ioaddr, START_CHAR(tty));
790                 mxser_set_must_xoff1_value(info->ioaddr, STOP_CHAR(tty));
791                 if (I_IXON(tty)) {
792                         mxser_enable_must_rx_software_flow_control(
793                                         info->ioaddr);
794                 } else {
795                         mxser_disable_must_rx_software_flow_control(
796                                         info->ioaddr);
797                 }
798                 if (I_IXOFF(tty)) {
799                         mxser_enable_must_tx_software_flow_control(
800                                         info->ioaddr);
801                 } else {
802                         mxser_disable_must_tx_software_flow_control(
803                                         info->ioaddr);
804                 }
805         }
806
807
808         outb(fcr, info->ioaddr + UART_FCR);     /* set fcr */
809         outb(cval, info->ioaddr + UART_LCR);
810
811         return ret;
812 }
813
814 static void mxser_check_modem_status(struct tty_struct *tty,
815                                 struct mxser_port *port, int status)
816 {
817         /* update input line counters */
818         if (status & UART_MSR_TERI)
819                 port->icount.rng++;
820         if (status & UART_MSR_DDSR)
821                 port->icount.dsr++;
822         if (status & UART_MSR_DDCD)
823                 port->icount.dcd++;
824         if (status & UART_MSR_DCTS)
825                 port->icount.cts++;
826         port->mon_data.modem_status = status;
827         wake_up_interruptible(&port->port.delta_msr_wait);
828
829         if ((port->port.flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
830                 if (status & UART_MSR_DCD)
831                         wake_up_interruptible(&port->port.open_wait);
832         }
833
834         if (port->port.flags & ASYNC_CTS_FLOW) {
835                 if (tty->hw_stopped) {
836                         if (status & UART_MSR_CTS) {
837                                 tty->hw_stopped = 0;
838
839                                 if ((port->type != PORT_16550A) &&
840                                                 (!port->board->chip_flag)) {
841                                         outb(port->IER & ~UART_IER_THRI,
842                                                 port->ioaddr + UART_IER);
843                                         port->IER |= UART_IER_THRI;
844                                         outb(port->IER, port->ioaddr +
845                                                         UART_IER);
846                                 }
847                                 tty_wakeup(tty);
848                         }
849                 } else {
850                         if (!(status & UART_MSR_CTS)) {
851                                 tty->hw_stopped = 1;
852                                 if (port->type != PORT_16550A &&
853                                                 !port->board->chip_flag) {
854                                         port->IER &= ~UART_IER_THRI;
855                                         outb(port->IER, port->ioaddr +
856                                                         UART_IER);
857                                 }
858                         }
859                 }
860         }
861 }
862
863 static int mxser_activate(struct tty_port *port, struct tty_struct *tty)
864 {
865         struct mxser_port *info = container_of(port, struct mxser_port, port);
866         unsigned long page;
867         unsigned long flags;
868
869         page = __get_free_page(GFP_KERNEL);
870         if (!page)
871                 return -ENOMEM;
872
873         spin_lock_irqsave(&info->slock, flags);
874
875         if (!info->ioaddr || !info->type) {
876                 set_bit(TTY_IO_ERROR, &tty->flags);
877                 free_page(page);
878                 spin_unlock_irqrestore(&info->slock, flags);
879                 return 0;
880         }
881         info->port.xmit_buf = (unsigned char *) page;
882
883         /*
884          * Clear the FIFO buffers and disable them
885          * (they will be reenabled in mxser_change_speed())
886          */
887         if (info->board->chip_flag)
888                 outb((UART_FCR_CLEAR_RCVR |
889                         UART_FCR_CLEAR_XMIT |
890                         MOXA_MUST_FCR_GDA_MODE_ENABLE), info->ioaddr + UART_FCR);
891         else
892                 outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
893                         info->ioaddr + UART_FCR);
894
895         /*
896          * At this point there's no way the LSR could still be 0xFF;
897          * if it is, then bail out, because there's likely no UART
898          * here.
899          */
900         if (inb(info->ioaddr + UART_LSR) == 0xff) {
901                 spin_unlock_irqrestore(&info->slock, flags);
902                 if (capable(CAP_SYS_ADMIN)) {
903                         set_bit(TTY_IO_ERROR, &tty->flags);
904                         return 0;
905                 } else
906                         return -ENODEV;
907         }
908
909         /*
910          * Clear the interrupt registers.
911          */
912         (void) inb(info->ioaddr + UART_LSR);
913         (void) inb(info->ioaddr + UART_RX);
914         (void) inb(info->ioaddr + UART_IIR);
915         (void) inb(info->ioaddr + UART_MSR);
916
917         /*
918          * Now, initialize the UART
919          */
920         outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR);  /* reset DLAB */
921         info->MCR = UART_MCR_DTR | UART_MCR_RTS;
922         outb(info->MCR, info->ioaddr + UART_MCR);
923
924         /*
925          * Finally, enable interrupts
926          */
927         info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI;
928
929         if (info->board->chip_flag)
930                 info->IER |= MOXA_MUST_IER_EGDAI;
931         outb(info->IER, info->ioaddr + UART_IER);       /* enable interrupts */
932
933         /*
934          * And clear the interrupt registers again for luck.
935          */
936         (void) inb(info->ioaddr + UART_LSR);
937         (void) inb(info->ioaddr + UART_RX);
938         (void) inb(info->ioaddr + UART_IIR);
939         (void) inb(info->ioaddr + UART_MSR);
940
941         clear_bit(TTY_IO_ERROR, &tty->flags);
942         info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
943
944         /*
945          * and set the speed of the serial port
946          */
947         mxser_change_speed(tty, NULL);
948         spin_unlock_irqrestore(&info->slock, flags);
949
950         return 0;
951 }
952
953 /*
954  * This routine will shutdown a serial port
955  */
956 static void mxser_shutdown_port(struct tty_port *port)
957 {
958         struct mxser_port *info = container_of(port, struct mxser_port, port);
959         unsigned long flags;
960
961         spin_lock_irqsave(&info->slock, flags);
962
963         /*
964          * clear delta_msr_wait queue to avoid mem leaks: we may free the irq
965          * here so the queue might never be waken up
966          */
967         wake_up_interruptible(&info->port.delta_msr_wait);
968
969         /*
970          * Free the xmit buffer, if necessary
971          */
972         if (info->port.xmit_buf) {
973                 free_page((unsigned long) info->port.xmit_buf);
974                 info->port.xmit_buf = NULL;
975         }
976
977         info->IER = 0;
978         outb(0x00, info->ioaddr + UART_IER);
979
980         /* clear Rx/Tx FIFO's */
981         if (info->board->chip_flag)
982                 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT |
983                                 MOXA_MUST_FCR_GDA_MODE_ENABLE,
984                                 info->ioaddr + UART_FCR);
985         else
986                 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
987                         info->ioaddr + UART_FCR);
988
989         /* read data port to reset things */
990         (void) inb(info->ioaddr + UART_RX);
991
992
993         if (info->board->chip_flag)
994                 SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(info->ioaddr);
995
996         spin_unlock_irqrestore(&info->slock, flags);
997 }
998
999 /*
1000  * This routine is called whenever a serial port is opened.  It
1001  * enables interrupts for a serial port, linking in its async structure into
1002  * the IRQ chain.   It also performs the serial-specific
1003  * initialization for the tty structure.
1004  */
1005 static int mxser_open(struct tty_struct *tty, struct file *filp)
1006 {
1007         struct mxser_port *info;
1008         int line;
1009
1010         line = tty->index;
1011         if (line == MXSER_PORTS)
1012                 return 0;
1013         if (line < 0 || line > MXSER_PORTS)
1014                 return -ENODEV;
1015         info = &mxser_boards[line / MXSER_PORTS_PER_BOARD].ports[line % MXSER_PORTS_PER_BOARD];
1016         if (!info->ioaddr)
1017                 return -ENODEV;
1018
1019         tty->driver_data = info;
1020         return tty_port_open(&info->port, tty, filp);
1021 }
1022
1023 static void mxser_flush_buffer(struct tty_struct *tty)
1024 {
1025         struct mxser_port *info = tty->driver_data;
1026         char fcr;
1027         unsigned long flags;
1028
1029
1030         spin_lock_irqsave(&info->slock, flags);
1031         info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
1032
1033         fcr = inb(info->ioaddr + UART_FCR);
1034         outb((fcr | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
1035                 info->ioaddr + UART_FCR);
1036         outb(fcr, info->ioaddr + UART_FCR);
1037
1038         spin_unlock_irqrestore(&info->slock, flags);
1039
1040         tty_wakeup(tty);
1041 }
1042
1043
1044 static void mxser_close_port(struct tty_port *port)
1045 {
1046         struct mxser_port *info = container_of(port, struct mxser_port, port);
1047         unsigned long timeout;
1048         /*
1049          * At this point we stop accepting input.  To do this, we
1050          * disable the receive line status interrupts, and tell the
1051          * interrupt driver to stop checking the data ready bit in the
1052          * line status register.
1053          */
1054         info->IER &= ~UART_IER_RLSI;
1055         if (info->board->chip_flag)
1056                 info->IER &= ~MOXA_MUST_RECV_ISR;
1057
1058         outb(info->IER, info->ioaddr + UART_IER);
1059         /*
1060          * Before we drop DTR, make sure the UART transmitter
1061          * has completely drained; this is especially
1062          * important if there is a transmit FIFO!
1063          */
1064         timeout = jiffies + HZ;
1065         while (!(inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT)) {
1066                 schedule_timeout_interruptible(5);
1067                 if (time_after(jiffies, timeout))
1068                         break;
1069         }
1070 }
1071
1072 /*
1073  * This routine is called when the serial port gets closed.  First, we
1074  * wait for the last remaining data to be sent.  Then, we unlink its
1075  * async structure from the interrupt chain if necessary, and we free
1076  * that IRQ if nothing is left in the chain.
1077  */
1078 static void mxser_close(struct tty_struct *tty, struct file *filp)
1079 {
1080         struct mxser_port *info = tty->driver_data;
1081         struct tty_port *port = &info->port;
1082
1083         if (tty->index == MXSER_PORTS || info == NULL)
1084                 return;
1085         if (tty_port_close_start(port, tty, filp) == 0)
1086                 return;
1087         mutex_lock(&port->mutex);
1088         mxser_close_port(port);
1089         mxser_flush_buffer(tty);
1090         mxser_shutdown_port(port);
1091         clear_bit(ASYNCB_INITIALIZED, &port->flags);
1092         mutex_unlock(&port->mutex);
1093         /* Right now the tty_port set is done outside of the close_end helper
1094            as we don't yet have everyone using refcounts */     
1095         tty_port_close_end(port, tty);
1096         tty_port_tty_set(port, NULL);
1097 }
1098
1099 static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int count)
1100 {
1101         int c, total = 0;
1102         struct mxser_port *info = tty->driver_data;
1103         unsigned long flags;
1104
1105         if (!info->port.xmit_buf)
1106                 return 0;
1107
1108         while (1) {
1109                 c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
1110                                           SERIAL_XMIT_SIZE - info->xmit_head));
1111                 if (c <= 0)
1112                         break;
1113
1114                 memcpy(info->port.xmit_buf + info->xmit_head, buf, c);
1115                 spin_lock_irqsave(&info->slock, flags);
1116                 info->xmit_head = (info->xmit_head + c) &
1117                                   (SERIAL_XMIT_SIZE - 1);
1118                 info->xmit_cnt += c;
1119                 spin_unlock_irqrestore(&info->slock, flags);
1120
1121                 buf += c;
1122                 count -= c;
1123                 total += c;
1124         }
1125
1126         if (info->xmit_cnt && !tty->stopped) {
1127                 if (!tty->hw_stopped ||
1128                                 (info->type == PORT_16550A) ||
1129                                 (info->board->chip_flag)) {
1130                         spin_lock_irqsave(&info->slock, flags);
1131                         outb(info->IER & ~UART_IER_THRI, info->ioaddr +
1132                                         UART_IER);
1133                         info->IER |= UART_IER_THRI;
1134                         outb(info->IER, info->ioaddr + UART_IER);
1135                         spin_unlock_irqrestore(&info->slock, flags);
1136                 }
1137         }
1138         return total;
1139 }
1140
1141 static int mxser_put_char(struct tty_struct *tty, unsigned char ch)
1142 {
1143         struct mxser_port *info = tty->driver_data;
1144         unsigned long flags;
1145
1146         if (!info->port.xmit_buf)
1147                 return 0;
1148
1149         if (info->xmit_cnt >= SERIAL_XMIT_SIZE - 1)
1150                 return 0;
1151
1152         spin_lock_irqsave(&info->slock, flags);
1153         info->port.xmit_buf[info->xmit_head++] = ch;
1154         info->xmit_head &= SERIAL_XMIT_SIZE - 1;
1155         info->xmit_cnt++;
1156         spin_unlock_irqrestore(&info->slock, flags);
1157         if (!tty->stopped) {
1158                 if (!tty->hw_stopped ||
1159                                 (info->type == PORT_16550A) ||
1160                                 info->board->chip_flag) {
1161                         spin_lock_irqsave(&info->slock, flags);
1162                         outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1163                         info->IER |= UART_IER_THRI;
1164                         outb(info->IER, info->ioaddr + UART_IER);
1165                         spin_unlock_irqrestore(&info->slock, flags);
1166                 }
1167         }
1168         return 1;
1169 }
1170
1171
1172 static void mxser_flush_chars(struct tty_struct *tty)
1173 {
1174         struct mxser_port *info = tty->driver_data;
1175         unsigned long flags;
1176
1177         if (info->xmit_cnt <= 0 || tty->stopped || !info->port.xmit_buf ||
1178                         (tty->hw_stopped && info->type != PORT_16550A &&
1179                          !info->board->chip_flag))
1180                 return;
1181
1182         spin_lock_irqsave(&info->slock, flags);
1183
1184         outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1185         info->IER |= UART_IER_THRI;
1186         outb(info->IER, info->ioaddr + UART_IER);
1187
1188         spin_unlock_irqrestore(&info->slock, flags);
1189 }
1190
1191 static int mxser_write_room(struct tty_struct *tty)
1192 {
1193         struct mxser_port *info = tty->driver_data;
1194         int ret;
1195
1196         ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
1197         return ret < 0 ? 0 : ret;
1198 }
1199
1200 static int mxser_chars_in_buffer(struct tty_struct *tty)
1201 {
1202         struct mxser_port *info = tty->driver_data;
1203         return info->xmit_cnt;
1204 }
1205
1206 /*
1207  * ------------------------------------------------------------
1208  * friends of mxser_ioctl()
1209  * ------------------------------------------------------------
1210  */
1211 static int mxser_get_serial_info(struct tty_struct *tty,
1212                 struct serial_struct __user *retinfo)
1213 {
1214         struct mxser_port *info = tty->driver_data;
1215         struct serial_struct tmp = {
1216                 .type = info->type,
1217                 .line = tty->index,
1218                 .port = info->ioaddr,
1219                 .irq = info->board->irq,
1220                 .flags = info->port.flags,
1221                 .baud_base = info->baud_base,
1222                 .close_delay = info->port.close_delay,
1223                 .closing_wait = info->port.closing_wait,
1224                 .custom_divisor = info->custom_divisor,
1225                 .hub6 = 0
1226         };
1227         if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
1228                 return -EFAULT;
1229         return 0;
1230 }
1231
1232 static int mxser_set_serial_info(struct tty_struct *tty,
1233                 struct serial_struct __user *new_info)
1234 {
1235         struct mxser_port *info = tty->driver_data;
1236         struct tty_port *port = &info->port;
1237         struct serial_struct new_serial;
1238         speed_t baud;
1239         unsigned long sl_flags;
1240         unsigned int flags;
1241         int retval = 0;
1242
1243         if (!new_info || !info->ioaddr)
1244                 return -ENODEV;
1245         if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
1246                 return -EFAULT;
1247
1248         if (new_serial.irq != info->board->irq ||
1249                         new_serial.port != info->ioaddr)
1250                 return -EINVAL;
1251
1252         flags = port->flags & ASYNC_SPD_MASK;
1253
1254         if (!capable(CAP_SYS_ADMIN)) {
1255                 if ((new_serial.baud_base != info->baud_base) ||
1256                                 (new_serial.close_delay != info->port.close_delay) ||
1257                                 ((new_serial.flags & ~ASYNC_USR_MASK) != (info->port.flags & ~ASYNC_USR_MASK)))
1258                         return -EPERM;
1259                 info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) |
1260                                 (new_serial.flags & ASYNC_USR_MASK));
1261         } else {
1262                 /*
1263                  * OK, past this point, all the error checking has been done.
1264                  * At this point, we start making changes.....
1265                  */
1266                 port->flags = ((port->flags & ~ASYNC_FLAGS) |
1267                                 (new_serial.flags & ASYNC_FLAGS));
1268                 port->close_delay = new_serial.close_delay * HZ / 100;
1269                 port->closing_wait = new_serial.closing_wait * HZ / 100;
1270                 tty->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
1271                 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST &&
1272                                 (new_serial.baud_base != info->baud_base ||
1273                                 new_serial.custom_divisor !=
1274                                 info->custom_divisor)) {
1275                         if (new_serial.custom_divisor == 0)
1276                                 return -EINVAL;
1277                         baud = new_serial.baud_base / new_serial.custom_divisor;
1278                         tty_encode_baud_rate(tty, baud, baud);
1279                 }
1280         }
1281
1282         info->type = new_serial.type;
1283
1284         process_txrx_fifo(info);
1285
1286         if (test_bit(ASYNCB_INITIALIZED, &port->flags)) {
1287                 if (flags != (port->flags & ASYNC_SPD_MASK)) {
1288                         spin_lock_irqsave(&info->slock, sl_flags);
1289                         mxser_change_speed(tty, NULL);
1290                         spin_unlock_irqrestore(&info->slock, sl_flags);
1291                 }
1292         } else {
1293                 retval = mxser_activate(port, tty);
1294                 if (retval == 0)
1295                         set_bit(ASYNCB_INITIALIZED, &port->flags);
1296         }
1297         return retval;
1298 }
1299
1300 /*
1301  * mxser_get_lsr_info - get line status register info
1302  *
1303  * Purpose: Let user call ioctl() to get info when the UART physically
1304  *          is emptied.  On bus types like RS485, the transmitter must
1305  *          release the bus after transmitting. This must be done when
1306  *          the transmit shift register is empty, not be done when the
1307  *          transmit holding register is empty.  This functionality
1308  *          allows an RS485 driver to be written in user space.
1309  */
1310 static int mxser_get_lsr_info(struct mxser_port *info,
1311                 unsigned int __user *value)
1312 {
1313         unsigned char status;
1314         unsigned int result;
1315         unsigned long flags;
1316
1317         spin_lock_irqsave(&info->slock, flags);
1318         status = inb(info->ioaddr + UART_LSR);
1319         spin_unlock_irqrestore(&info->slock, flags);
1320         result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
1321         return put_user(result, value);
1322 }
1323
1324 static int mxser_tiocmget(struct tty_struct *tty)
1325 {
1326         struct mxser_port *info = tty->driver_data;
1327         unsigned char control, status;
1328         unsigned long flags;
1329
1330
1331         if (tty->index == MXSER_PORTS)
1332                 return -ENOIOCTLCMD;
1333         if (test_bit(TTY_IO_ERROR, &tty->flags))
1334                 return -EIO;
1335
1336         control = info->MCR;
1337
1338         spin_lock_irqsave(&info->slock, flags);
1339         status = inb(info->ioaddr + UART_MSR);
1340         if (status & UART_MSR_ANY_DELTA)
1341                 mxser_check_modem_status(tty, info, status);
1342         spin_unlock_irqrestore(&info->slock, flags);
1343         return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) |
1344                     ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) |
1345                     ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) |
1346                     ((status & UART_MSR_RI) ? TIOCM_RNG : 0) |
1347                     ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) |
1348                     ((status & UART_MSR_CTS) ? TIOCM_CTS : 0);
1349 }
1350
1351 static int mxser_tiocmset(struct tty_struct *tty,
1352                 unsigned int set, unsigned int clear)
1353 {
1354         struct mxser_port *info = tty->driver_data;
1355         unsigned long flags;
1356
1357
1358         if (tty->index == MXSER_PORTS)
1359                 return -ENOIOCTLCMD;
1360         if (test_bit(TTY_IO_ERROR, &tty->flags))
1361                 return -EIO;
1362
1363         spin_lock_irqsave(&info->slock, flags);
1364
1365         if (set & TIOCM_RTS)
1366                 info->MCR |= UART_MCR_RTS;
1367         if (set & TIOCM_DTR)
1368                 info->MCR |= UART_MCR_DTR;
1369
1370         if (clear & TIOCM_RTS)
1371                 info->MCR &= ~UART_MCR_RTS;
1372         if (clear & TIOCM_DTR)
1373                 info->MCR &= ~UART_MCR_DTR;
1374
1375         outb(info->MCR, info->ioaddr + UART_MCR);
1376         spin_unlock_irqrestore(&info->slock, flags);
1377         return 0;
1378 }
1379
1380 static int __init mxser_program_mode(int port)
1381 {
1382         int id, i, j, n;
1383
1384         outb(0, port);
1385         outb(0, port);
1386         outb(0, port);
1387         (void)inb(port);
1388         (void)inb(port);
1389         outb(0, port);
1390         (void)inb(port);
1391
1392         id = inb(port + 1) & 0x1F;
1393         if ((id != C168_ASIC_ID) &&
1394                         (id != C104_ASIC_ID) &&
1395                         (id != C102_ASIC_ID) &&
1396                         (id != CI132_ASIC_ID) &&
1397                         (id != CI134_ASIC_ID) &&
1398                         (id != CI104J_ASIC_ID))
1399                 return -1;
1400         for (i = 0, j = 0; i < 4; i++) {
1401                 n = inb(port + 2);
1402                 if (n == 'M') {
1403                         j = 1;
1404                 } else if ((j == 1) && (n == 1)) {
1405                         j = 2;
1406                         break;
1407                 } else
1408                         j = 0;
1409         }
1410         if (j != 2)
1411                 id = -2;
1412         return id;
1413 }
1414
1415 static void __init mxser_normal_mode(int port)
1416 {
1417         int i, n;
1418
1419         outb(0xA5, port + 1);
1420         outb(0x80, port + 3);
1421         outb(12, port + 0);     /* 9600 bps */
1422         outb(0, port + 1);
1423         outb(0x03, port + 3);   /* 8 data bits */
1424         outb(0x13, port + 4);   /* loop back mode */
1425         for (i = 0; i < 16; i++) {
1426                 n = inb(port + 5);
1427                 if ((n & 0x61) == 0x60)
1428                         break;
1429                 if ((n & 1) == 1)
1430                         (void)inb(port);
1431         }
1432         outb(0x00, port + 4);
1433 }
1434
1435 #define CHIP_SK         0x01    /* Serial Data Clock  in Eprom */
1436 #define CHIP_DO         0x02    /* Serial Data Output in Eprom */
1437 #define CHIP_CS         0x04    /* Serial Chip Select in Eprom */
1438 #define CHIP_DI         0x08    /* Serial Data Input  in Eprom */
1439 #define EN_CCMD         0x000   /* Chip's command register     */
1440 #define EN0_RSARLO      0x008   /* Remote start address reg 0  */
1441 #define EN0_RSARHI      0x009   /* Remote start address reg 1  */
1442 #define EN0_RCNTLO      0x00A   /* Remote byte count reg WR    */
1443 #define EN0_RCNTHI      0x00B   /* Remote byte count reg WR    */
1444 #define EN0_DCFG        0x00E   /* Data configuration reg WR   */
1445 #define EN0_PORT        0x010   /* Rcv missed frame error counter RD */
1446 #define ENC_PAGE0       0x000   /* Select page 0 of chip registers   */
1447 #define ENC_PAGE3       0x0C0   /* Select page 3 of chip registers   */
1448 static int __init mxser_read_register(int port, unsigned short *regs)
1449 {
1450         int i, k, value, id;
1451         unsigned int j;
1452
1453         id = mxser_program_mode(port);
1454         if (id < 0)
1455                 return id;
1456         for (i = 0; i < 14; i++) {
1457                 k = (i & 0x3F) | 0x180;
1458                 for (j = 0x100; j > 0; j >>= 1) {
1459                         outb(CHIP_CS, port);
1460                         if (k & j) {
1461                                 outb(CHIP_CS | CHIP_DO, port);
1462                                 outb(CHIP_CS | CHIP_DO | CHIP_SK, port);        /* A? bit of read */
1463                         } else {
1464                                 outb(CHIP_CS, port);
1465                                 outb(CHIP_CS | CHIP_SK, port);  /* A? bit of read */
1466                         }
1467                 }
1468                 (void)inb(port);
1469                 value = 0;
1470                 for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) {
1471                         outb(CHIP_CS, port);
1472                         outb(CHIP_CS | CHIP_SK, port);
1473                         if (inb(port) & CHIP_DI)
1474                                 value |= j;
1475                 }
1476                 regs[i] = value;
1477                 outb(0, port);
1478         }
1479         mxser_normal_mode(port);
1480         return id;
1481 }
1482
1483 static int mxser_ioctl_special(unsigned int cmd, void __user *argp)
1484 {
1485         struct mxser_port *ip;
1486         struct tty_port *port;
1487         struct tty_struct *tty;
1488         int result, status;
1489         unsigned int i, j;
1490         int ret = 0;
1491
1492         switch (cmd) {
1493         case MOXA_GET_MAJOR:
1494                 printk_ratelimited(KERN_WARNING "mxser: '%s' uses deprecated ioctl "
1495                                         "%x (GET_MAJOR), fix your userspace\n",
1496                                         current->comm, cmd);
1497                 return put_user(ttymajor, (int __user *)argp);
1498
1499         case MOXA_CHKPORTENABLE:
1500                 result = 0;
1501                 for (i = 0; i < MXSER_BOARDS; i++)
1502                         for (j = 0; j < MXSER_PORTS_PER_BOARD; j++)
1503                                 if (mxser_boards[i].ports[j].ioaddr)
1504                                         result |= (1 << i);
1505                 return put_user(result, (unsigned long __user *)argp);
1506         case MOXA_GETDATACOUNT:
1507                 /* The receive side is locked by port->slock but it isn't
1508                    clear that an exact snapshot is worth copying here */
1509                 if (copy_to_user(argp, &mxvar_log, sizeof(mxvar_log)))
1510                         ret = -EFAULT;
1511                 return ret;
1512         case MOXA_GETMSTATUS: {
1513                 struct mxser_mstatus ms, __user *msu = argp;
1514                 for (i = 0; i < MXSER_BOARDS; i++)
1515                         for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) {
1516                                 ip = &mxser_boards[i].ports[j];
1517                                 port = &ip->port;
1518                                 memset(&ms, 0, sizeof(ms));
1519
1520                                 mutex_lock(&port->mutex);
1521                                 if (!ip->ioaddr)
1522                                         goto copy;
1523                                 
1524                                 tty = tty_port_tty_get(port);
1525
1526                                 if (!tty || !tty->termios)
1527                                         ms.cflag = ip->normal_termios.c_cflag;
1528                                 else
1529                                         ms.cflag = tty->termios->c_cflag;
1530                                 tty_kref_put(tty);
1531                                 spin_lock_irq(&ip->slock);
1532                                 status = inb(ip->ioaddr + UART_MSR);
1533                                 spin_unlock_irq(&ip->slock);
1534                                 if (status & UART_MSR_DCD)
1535                                         ms.dcd = 1;
1536                                 if (status & UART_MSR_DSR)
1537                                         ms.dsr = 1;
1538                                 if (status & UART_MSR_CTS)
1539                                         ms.cts = 1;
1540                         copy:
1541                                 mutex_unlock(&port->mutex);
1542                                 if (copy_to_user(msu, &ms, sizeof(ms)))
1543                                         return -EFAULT;
1544                                 msu++;
1545                         }
1546                 return 0;
1547         }
1548         case MOXA_ASPP_MON_EXT: {
1549                 struct mxser_mon_ext *me; /* it's 2k, stack unfriendly */
1550                 unsigned int cflag, iflag, p;
1551                 u8 opmode;
1552
1553                 me = kzalloc(sizeof(*me), GFP_KERNEL);
1554                 if (!me)
1555                         return -ENOMEM;
1556
1557                 for (i = 0, p = 0; i < MXSER_BOARDS; i++) {
1558                         for (j = 0; j < MXSER_PORTS_PER_BOARD; j++, p++) {
1559                                 if (p >= ARRAY_SIZE(me->rx_cnt)) {
1560                                         i = MXSER_BOARDS;
1561                                         break;
1562                                 }
1563                                 ip = &mxser_boards[i].ports[j];
1564                                 port = &ip->port;
1565
1566                                 mutex_lock(&port->mutex);
1567                                 if (!ip->ioaddr) {
1568                                         mutex_unlock(&port->mutex);
1569                                         continue;
1570                                 }
1571
1572                                 spin_lock_irq(&ip->slock);
1573                                 status = mxser_get_msr(ip->ioaddr, 0, p);
1574
1575                                 if (status & UART_MSR_TERI)
1576                                         ip->icount.rng++;
1577                                 if (status & UART_MSR_DDSR)
1578                                         ip->icount.dsr++;
1579                                 if (status & UART_MSR_DDCD)
1580                                         ip->icount.dcd++;
1581                                 if (status & UART_MSR_DCTS)
1582                                         ip->icount.cts++;
1583
1584                                 ip->mon_data.modem_status = status;
1585                                 me->rx_cnt[p] = ip->mon_data.rxcnt;
1586                                 me->tx_cnt[p] = ip->mon_data.txcnt;
1587                                 me->up_rxcnt[p] = ip->mon_data.up_rxcnt;
1588                                 me->up_txcnt[p] = ip->mon_data.up_txcnt;
1589                                 me->modem_status[p] =
1590                                         ip->mon_data.modem_status;
1591                                 spin_unlock_irq(&ip->slock);
1592
1593                                 tty = tty_port_tty_get(&ip->port);
1594
1595                                 if (!tty || !tty->termios) {
1596                                         cflag = ip->normal_termios.c_cflag;
1597                                         iflag = ip->normal_termios.c_iflag;
1598                                         me->baudrate[p] = tty_termios_baud_rate(&ip->normal_termios);
1599                                 } else {
1600                                         cflag = tty->termios->c_cflag;
1601                                         iflag = tty->termios->c_iflag;
1602                                         me->baudrate[p] = tty_get_baud_rate(tty);
1603                                 }
1604                                 tty_kref_put(tty);
1605
1606                                 me->databits[p] = cflag & CSIZE;
1607                                 me->stopbits[p] = cflag & CSTOPB;
1608                                 me->parity[p] = cflag & (PARENB | PARODD |
1609                                                 CMSPAR);
1610
1611                                 if (cflag & CRTSCTS)
1612                                         me->flowctrl[p] |= 0x03;
1613
1614                                 if (iflag & (IXON | IXOFF))
1615                                         me->flowctrl[p] |= 0x0C;
1616
1617                                 if (ip->type == PORT_16550A)
1618                                         me->fifo[p] = 1;
1619
1620                                 opmode = inb(ip->opmode_ioaddr)>>((p % 4) * 2);
1621                                 opmode &= OP_MODE_MASK;
1622                                 me->iftype[p] = opmode;
1623                                 mutex_unlock(&port->mutex);
1624                         }
1625                 }
1626                 if (copy_to_user(argp, me, sizeof(*me)))
1627                         ret = -EFAULT;
1628                 kfree(me);
1629                 return ret;
1630         }
1631         default:
1632                 return -ENOIOCTLCMD;
1633         }
1634         return 0;
1635 }
1636
1637 static int mxser_cflags_changed(struct mxser_port *info, unsigned long arg,
1638                 struct async_icount *cprev)
1639 {
1640         struct async_icount cnow;
1641         unsigned long flags;
1642         int ret;
1643
1644         spin_lock_irqsave(&info->slock, flags);
1645         cnow = info->icount;    /* atomic copy */
1646         spin_unlock_irqrestore(&info->slock, flags);
1647
1648         ret =   ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) ||
1649                 ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) ||
1650                 ((arg & TIOCM_CD)  && (cnow.dcd != cprev->dcd)) ||
1651                 ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts));
1652
1653         *cprev = cnow;
1654
1655         return ret;
1656 }
1657
1658 static int mxser_ioctl(struct tty_struct *tty,
1659                 unsigned int cmd, unsigned long arg)
1660 {
1661         struct mxser_port *info = tty->driver_data;
1662         struct tty_port *port = &info->port;
1663         struct async_icount cnow;
1664         unsigned long flags;
1665         void __user *argp = (void __user *)arg;
1666         int retval;
1667
1668         if (tty->index == MXSER_PORTS)
1669                 return mxser_ioctl_special(cmd, argp);
1670
1671         if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE) {
1672                 int p;
1673                 unsigned long opmode;
1674                 static unsigned char ModeMask[] = { 0xfc, 0xf3, 0xcf, 0x3f };
1675                 int shiftbit;
1676                 unsigned char val, mask;
1677
1678                 p = tty->index % 4;
1679                 if (cmd == MOXA_SET_OP_MODE) {
1680                         if (get_user(opmode, (int __user *) argp))
1681                                 return -EFAULT;
1682                         if (opmode != RS232_MODE &&
1683                                         opmode != RS485_2WIRE_MODE &&
1684                                         opmode != RS422_MODE &&
1685                                         opmode != RS485_4WIRE_MODE)
1686                                 return -EFAULT;
1687                         mask = ModeMask[p];
1688                         shiftbit = p * 2;
1689                         spin_lock_irq(&info->slock);
1690                         val = inb(info->opmode_ioaddr);
1691                         val &= mask;
1692                         val |= (opmode << shiftbit);
1693                         outb(val, info->opmode_ioaddr);
1694                         spin_unlock_irq(&info->slock);
1695                 } else {
1696                         shiftbit = p * 2;
1697                         spin_lock_irq(&info->slock);
1698                         opmode = inb(info->opmode_ioaddr) >> shiftbit;
1699                         spin_unlock_irq(&info->slock);
1700                         opmode &= OP_MODE_MASK;
1701                         if (put_user(opmode, (int __user *)argp))
1702                                 return -EFAULT;
1703                 }
1704                 return 0;
1705         }
1706
1707         if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT &&
1708                         test_bit(TTY_IO_ERROR, &tty->flags))
1709                 return -EIO;
1710
1711         switch (cmd) {
1712         case TIOCGSERIAL:
1713                 mutex_lock(&port->mutex);
1714                 retval = mxser_get_serial_info(tty, argp);
1715                 mutex_unlock(&port->mutex);
1716                 return retval;
1717         case TIOCSSERIAL:
1718                 mutex_lock(&port->mutex);
1719                 retval = mxser_set_serial_info(tty, argp);
1720                 mutex_unlock(&port->mutex);
1721                 return retval;
1722         case TIOCSERGETLSR:     /* Get line status register */
1723                 return  mxser_get_lsr_info(info, argp);
1724                 /*
1725                  * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
1726                  * - mask passed in arg for lines of interest
1727                  *   (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
1728                  * Caller should use TIOCGICOUNT to see which one it was
1729                  */
1730         case TIOCMIWAIT:
1731                 spin_lock_irqsave(&info->slock, flags);
1732                 cnow = info->icount;    /* note the counters on entry */
1733                 spin_unlock_irqrestore(&info->slock, flags);
1734
1735                 return wait_event_interruptible(info->port.delta_msr_wait,
1736                                 mxser_cflags_changed(info, arg, &cnow));
1737         case MOXA_HighSpeedOn:
1738                 return put_user(info->baud_base != 115200 ? 1 : 0, (int __user *)argp);
1739         case MOXA_SDS_RSTICOUNTER:
1740                 spin_lock_irq(&info->slock);
1741                 info->mon_data.rxcnt = 0;
1742                 info->mon_data.txcnt = 0;
1743                 spin_unlock_irq(&info->slock);
1744                 return 0;
1745
1746         case MOXA_ASPP_OQUEUE:{
1747                 int len, lsr;
1748
1749                 len = mxser_chars_in_buffer(tty);
1750                 spin_lock_irq(&info->slock);
1751                 lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_THRE;
1752                 spin_unlock_irq(&info->slock);
1753                 len += (lsr ? 0 : 1);
1754
1755                 return put_user(len, (int __user *)argp);
1756         }
1757         case MOXA_ASPP_MON: {
1758                 int mcr, status;
1759
1760                 spin_lock_irq(&info->slock);
1761                 status = mxser_get_msr(info->ioaddr, 1, tty->index);
1762                 mxser_check_modem_status(tty, info, status);
1763
1764                 mcr = inb(info->ioaddr + UART_MCR);
1765                 spin_unlock_irq(&info->slock);
1766
1767                 if (mcr & MOXA_MUST_MCR_XON_FLAG)
1768                         info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFHOLD;
1769                 else
1770                         info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFHOLD;
1771
1772                 if (mcr & MOXA_MUST_MCR_TX_XON)
1773                         info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFXENT;
1774                 else
1775                         info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT;
1776
1777                 if (tty->hw_stopped)
1778                         info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD;
1779                 else
1780                         info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD;
1781
1782                 if (copy_to_user(argp, &info->mon_data,
1783                                 sizeof(struct mxser_mon)))
1784                         return -EFAULT;
1785
1786                 return 0;
1787         }
1788         case MOXA_ASPP_LSTATUS: {
1789                 if (put_user(info->err_shadow, (unsigned char __user *)argp))
1790                         return -EFAULT;
1791
1792                 info->err_shadow = 0;
1793                 return 0;
1794         }
1795         case MOXA_SET_BAUD_METHOD: {
1796                 int method;
1797
1798                 if (get_user(method, (int __user *)argp))
1799                         return -EFAULT;
1800                 mxser_set_baud_method[tty->index] = method;
1801                 return put_user(method, (int __user *)argp);
1802         }
1803         default:
1804                 return -ENOIOCTLCMD;
1805         }
1806         return 0;
1807 }
1808
1809         /*
1810          * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
1811          * Return: write counters to the user passed counter struct
1812          * NB: both 1->0 and 0->1 transitions are counted except for
1813          *     RI where only 0->1 is counted.
1814          */
1815
1816 static int mxser_get_icount(struct tty_struct *tty,
1817                 struct serial_icounter_struct *icount)
1818
1819 {
1820         struct mxser_port *info = tty->driver_data;
1821         struct async_icount cnow;
1822         unsigned long flags;
1823
1824         spin_lock_irqsave(&info->slock, flags);
1825         cnow = info->icount;
1826         spin_unlock_irqrestore(&info->slock, flags);
1827
1828         icount->frame = cnow.frame;
1829         icount->brk = cnow.brk;
1830         icount->overrun = cnow.overrun;
1831         icount->buf_overrun = cnow.buf_overrun;
1832         icount->parity = cnow.parity;
1833         icount->rx = cnow.rx;
1834         icount->tx = cnow.tx;
1835         icount->cts = cnow.cts;
1836         icount->dsr = cnow.dsr;
1837         icount->rng = cnow.rng;
1838         icount->dcd = cnow.dcd;
1839         return 0;
1840 }
1841
1842 static void mxser_stoprx(struct tty_struct *tty)
1843 {
1844         struct mxser_port *info = tty->driver_data;
1845
1846         info->ldisc_stop_rx = 1;
1847         if (I_IXOFF(tty)) {
1848                 if (info->board->chip_flag) {
1849                         info->IER &= ~MOXA_MUST_RECV_ISR;
1850                         outb(info->IER, info->ioaddr + UART_IER);
1851                 } else {
1852                         info->x_char = STOP_CHAR(tty);
1853                         outb(0, info->ioaddr + UART_IER);
1854                         info->IER |= UART_IER_THRI;
1855                         outb(info->IER, info->ioaddr + UART_IER);
1856                 }
1857         }
1858
1859         if (tty->termios->c_cflag & CRTSCTS) {
1860                 info->MCR &= ~UART_MCR_RTS;
1861                 outb(info->MCR, info->ioaddr + UART_MCR);
1862         }
1863 }
1864
1865 /*
1866  * This routine is called by the upper-layer tty layer to signal that
1867  * incoming characters should be throttled.
1868  */
1869 static void mxser_throttle(struct tty_struct *tty)
1870 {
1871         mxser_stoprx(tty);
1872 }
1873
1874 static void mxser_unthrottle(struct tty_struct *tty)
1875 {
1876         struct mxser_port *info = tty->driver_data;
1877
1878         /* startrx */
1879         info->ldisc_stop_rx = 0;
1880         if (I_IXOFF(tty)) {
1881                 if (info->x_char)
1882                         info->x_char = 0;
1883                 else {
1884                         if (info->board->chip_flag) {
1885                                 info->IER |= MOXA_MUST_RECV_ISR;
1886                                 outb(info->IER, info->ioaddr + UART_IER);
1887                         } else {
1888                                 info->x_char = START_CHAR(tty);
1889                                 outb(0, info->ioaddr + UART_IER);
1890                                 info->IER |= UART_IER_THRI;
1891                                 outb(info->IER, info->ioaddr + UART_IER);
1892                         }
1893                 }
1894         }
1895
1896         if (tty->termios->c_cflag & CRTSCTS) {
1897                 info->MCR |= UART_MCR_RTS;
1898                 outb(info->MCR, info->ioaddr + UART_MCR);
1899         }
1900 }
1901
1902 /*
1903  * mxser_stop() and mxser_start()
1904  *
1905  * This routines are called before setting or resetting tty->stopped.
1906  * They enable or disable transmitter interrupts, as necessary.
1907  */
1908 static void mxser_stop(struct tty_struct *tty)
1909 {
1910         struct mxser_port *info = tty->driver_data;
1911         unsigned long flags;
1912
1913         spin_lock_irqsave(&info->slock, flags);
1914         if (info->IER & UART_IER_THRI) {
1915                 info->IER &= ~UART_IER_THRI;
1916                 outb(info->IER, info->ioaddr + UART_IER);
1917         }
1918         spin_unlock_irqrestore(&info->slock, flags);
1919 }
1920
1921 static void mxser_start(struct tty_struct *tty)
1922 {
1923         struct mxser_port *info = tty->driver_data;
1924         unsigned long flags;
1925
1926         spin_lock_irqsave(&info->slock, flags);
1927         if (info->xmit_cnt && info->port.xmit_buf) {
1928                 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1929                 info->IER |= UART_IER_THRI;
1930                 outb(info->IER, info->ioaddr + UART_IER);
1931         }
1932         spin_unlock_irqrestore(&info->slock, flags);
1933 }
1934
1935 static void mxser_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
1936 {
1937         struct mxser_port *info = tty->driver_data;
1938         unsigned long flags;
1939
1940         spin_lock_irqsave(&info->slock, flags);
1941         mxser_change_speed(tty, old_termios);
1942         spin_unlock_irqrestore(&info->slock, flags);
1943
1944         if ((old_termios->c_cflag & CRTSCTS) &&
1945                         !(tty->termios->c_cflag & CRTSCTS)) {
1946                 tty->hw_stopped = 0;
1947                 mxser_start(tty);
1948         }
1949
1950         /* Handle sw stopped */
1951         if ((old_termios->c_iflag & IXON) &&
1952                         !(tty->termios->c_iflag & IXON)) {
1953                 tty->stopped = 0;
1954
1955                 if (info->board->chip_flag) {
1956                         spin_lock_irqsave(&info->slock, flags);
1957                         mxser_disable_must_rx_software_flow_control(
1958                                         info->ioaddr);
1959                         spin_unlock_irqrestore(&info->slock, flags);
1960                 }
1961
1962                 mxser_start(tty);
1963         }
1964 }
1965
1966 /*
1967  * mxser_wait_until_sent() --- wait until the transmitter is empty
1968  */
1969 static void mxser_wait_until_sent(struct tty_struct *tty, int timeout)
1970 {
1971         struct mxser_port *info = tty->driver_data;
1972         unsigned long orig_jiffies, char_time;
1973         unsigned long flags;
1974         int lsr;
1975
1976         if (info->type == PORT_UNKNOWN)
1977                 return;
1978
1979         if (info->xmit_fifo_size == 0)
1980                 return;         /* Just in case.... */
1981
1982         orig_jiffies = jiffies;
1983         /*
1984          * Set the check interval to be 1/5 of the estimated time to
1985          * send a single character, and make it at least 1.  The check
1986          * interval should also be less than the timeout.
1987          *
1988          * Note: we have to use pretty tight timings here to satisfy
1989          * the NIST-PCTS.
1990          */
1991         char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size;
1992         char_time = char_time / 5;
1993         if (char_time == 0)
1994                 char_time = 1;
1995         if (timeout && timeout < char_time)
1996                 char_time = timeout;
1997         /*
1998          * If the transmitter hasn't cleared in twice the approximate
1999          * amount of time to send the entire FIFO, it probably won't
2000          * ever clear.  This assumes the UART isn't doing flow
2001          * control, which is currently the case.  Hence, if it ever
2002          * takes longer than info->timeout, this is probably due to a
2003          * UART bug of some kind.  So, we clamp the timeout parameter at
2004          * 2*info->timeout.
2005          */
2006         if (!timeout || timeout > 2 * info->timeout)
2007                 timeout = 2 * info->timeout;
2008 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
2009         printk(KERN_DEBUG "In rs_wait_until_sent(%d) check=%lu...",
2010                 timeout, char_time);
2011         printk("jiff=%lu...", jiffies);
2012 #endif
2013         spin_lock_irqsave(&info->slock, flags);
2014         while (!((lsr = inb(info->ioaddr + UART_LSR)) & UART_LSR_TEMT)) {
2015 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
2016                 printk("lsr = %d (jiff=%lu)...", lsr, jiffies);
2017 #endif
2018                 spin_unlock_irqrestore(&info->slock, flags);
2019                 schedule_timeout_interruptible(char_time);
2020                 spin_lock_irqsave(&info->slock, flags);
2021                 if (signal_pending(current))
2022                         break;
2023                 if (timeout && time_after(jiffies, orig_jiffies + timeout))
2024                         break;
2025         }
2026         spin_unlock_irqrestore(&info->slock, flags);
2027         set_current_state(TASK_RUNNING);
2028
2029 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
2030         printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies);
2031 #endif
2032 }
2033
2034 /*
2035  * This routine is called by tty_hangup() when a hangup is signaled.
2036  */
2037 static void mxser_hangup(struct tty_struct *tty)
2038 {
2039         struct mxser_port *info = tty->driver_data;
2040
2041         mxser_flush_buffer(tty);
2042         tty_port_hangup(&info->port);
2043 }
2044
2045 /*
2046  * mxser_rs_break() --- routine which turns the break handling on or off
2047  */
2048 static int mxser_rs_break(struct tty_struct *tty, int break_state)
2049 {
2050         struct mxser_port *info = tty->driver_data;
2051         unsigned long flags;
2052
2053         spin_lock_irqsave(&info->slock, flags);
2054         if (break_state == -1)
2055                 outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC,
2056                         info->ioaddr + UART_LCR);
2057         else
2058                 outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC,
2059                         info->ioaddr + UART_LCR);
2060         spin_unlock_irqrestore(&info->slock, flags);
2061         return 0;
2062 }
2063
2064 static void mxser_receive_chars(struct tty_struct *tty,
2065                                 struct mxser_port *port, int *status)
2066 {
2067         unsigned char ch, gdl;
2068         int ignored = 0;
2069         int cnt = 0;
2070         int recv_room;
2071         int max = 256;
2072
2073         recv_room = tty->receive_room;
2074         if (recv_room == 0 && !port->ldisc_stop_rx)
2075                 mxser_stoprx(tty);
2076         if (port->board->chip_flag != MOXA_OTHER_UART) {
2077
2078                 if (*status & UART_LSR_SPECIAL)
2079                         goto intr_old;
2080                 if (port->board->chip_flag == MOXA_MUST_MU860_HWID &&
2081                                 (*status & MOXA_MUST_LSR_RERR))
2082                         goto intr_old;
2083                 if (*status & MOXA_MUST_LSR_RERR)
2084                         goto intr_old;
2085
2086                 gdl = inb(port->ioaddr + MOXA_MUST_GDL_REGISTER);
2087
2088                 if (port->board->chip_flag == MOXA_MUST_MU150_HWID)
2089                         gdl &= MOXA_MUST_GDL_MASK;
2090                 if (gdl >= recv_room) {
2091                         if (!port->ldisc_stop_rx)
2092                                 mxser_stoprx(tty);
2093                 }
2094                 while (gdl--) {
2095                         ch = inb(port->ioaddr + UART_RX);
2096                         tty_insert_flip_char(tty, ch, 0);
2097                         cnt++;
2098                 }
2099                 goto end_intr;
2100         }
2101 intr_old:
2102
2103         do {
2104                 if (max-- < 0)
2105                         break;
2106
2107                 ch = inb(port->ioaddr + UART_RX);
2108                 if (port->board->chip_flag && (*status & UART_LSR_OE))
2109                         outb(0x23, port->ioaddr + UART_FCR);
2110                 *status &= port->read_status_mask;
2111                 if (*status & port->ignore_status_mask) {
2112                         if (++ignored > 100)
2113                                 break;
2114                 } else {
2115                         char flag = 0;
2116                         if (*status & UART_LSR_SPECIAL) {
2117                                 if (*status & UART_LSR_BI) {
2118                                         flag = TTY_BREAK;
2119                                         port->icount.brk++;
2120
2121                                         if (port->port.flags & ASYNC_SAK)
2122                                                 do_SAK(tty);
2123                                 } else if (*status & UART_LSR_PE) {
2124                                         flag = TTY_PARITY;
2125                                         port->icount.parity++;
2126                                 } else if (*status & UART_LSR_FE) {
2127                                         flag = TTY_FRAME;
2128                                         port->icount.frame++;
2129                                 } else if (*status & UART_LSR_OE) {
2130                                         flag = TTY_OVERRUN;
2131                                         port->icount.overrun++;
2132                                 } else
2133                                         flag = TTY_BREAK;
2134                         }
2135                         tty_insert_flip_char(tty, ch, flag);
2136                         cnt++;
2137                         if (cnt >= recv_room) {
2138                                 if (!port->ldisc_stop_rx)
2139                                         mxser_stoprx(tty);
2140                                 break;
2141                         }
2142
2143                 }
2144
2145                 if (port->board->chip_flag)
2146                         break;
2147
2148                 *status = inb(port->ioaddr + UART_LSR);
2149         } while (*status & UART_LSR_DR);
2150
2151 end_intr:
2152         mxvar_log.rxcnt[tty->index] += cnt;
2153         port->mon_data.rxcnt += cnt;
2154         port->mon_data.up_rxcnt += cnt;
2155
2156         /*
2157          * We are called from an interrupt context with &port->slock
2158          * being held. Drop it temporarily in order to prevent
2159          * recursive locking.
2160          */
2161         spin_unlock(&port->slock);
2162         tty_flip_buffer_push(tty);
2163         spin_lock(&port->slock);
2164 }
2165
2166 static void mxser_transmit_chars(struct tty_struct *tty, struct mxser_port *port)
2167 {
2168         int count, cnt;
2169
2170         if (port->x_char) {
2171                 outb(port->x_char, port->ioaddr + UART_TX);
2172                 port->x_char = 0;
2173                 mxvar_log.txcnt[tty->index]++;
2174                 port->mon_data.txcnt++;
2175                 port->mon_data.up_txcnt++;
2176                 port->icount.tx++;
2177                 return;
2178         }
2179
2180         if (port->port.xmit_buf == NULL)
2181                 return;
2182
2183         if (port->xmit_cnt <= 0 || tty->stopped ||
2184                         (tty->hw_stopped &&
2185                         (port->type != PORT_16550A) &&
2186                         (!port->board->chip_flag))) {
2187                 port->IER &= ~UART_IER_THRI;
2188                 outb(port->IER, port->ioaddr + UART_IER);
2189                 return;
2190         }
2191
2192         cnt = port->xmit_cnt;
2193         count = port->xmit_fifo_size;
2194         do {
2195                 outb(port->port.xmit_buf[port->xmit_tail++],
2196                         port->ioaddr + UART_TX);
2197                 port->xmit_tail = port->xmit_tail & (SERIAL_XMIT_SIZE - 1);
2198                 if (--port->xmit_cnt <= 0)
2199                         break;
2200         } while (--count > 0);
2201         mxvar_log.txcnt[tty->index] += (cnt - port->xmit_cnt);
2202
2203         port->mon_data.txcnt += (cnt - port->xmit_cnt);
2204         port->mon_data.up_txcnt += (cnt - port->xmit_cnt);
2205         port->icount.tx += (cnt - port->xmit_cnt);
2206
2207         if (port->xmit_cnt < WAKEUP_CHARS)
2208                 tty_wakeup(tty);
2209
2210         if (port->xmit_cnt <= 0) {
2211                 port->IER &= ~UART_IER_THRI;
2212                 outb(port->IER, port->ioaddr + UART_IER);
2213         }
2214 }
2215
2216 /*
2217  * This is the serial driver's generic interrupt routine
2218  */
2219 static irqreturn_t mxser_interrupt(int irq, void *dev_id)
2220 {
2221         int status, iir, i;
2222         struct mxser_board *brd = NULL;
2223         struct mxser_port *port;
2224         int max, irqbits, bits, msr;
2225         unsigned int int_cnt, pass_counter = 0;
2226         int handled = IRQ_NONE;
2227         struct tty_struct *tty;
2228
2229         for (i = 0; i < MXSER_BOARDS; i++)
2230                 if (dev_id == &mxser_boards[i]) {
2231                         brd = dev_id;
2232                         break;
2233                 }
2234
2235         if (i == MXSER_BOARDS)
2236                 goto irq_stop;
2237         if (brd == NULL)
2238                 goto irq_stop;
2239         max = brd->info->nports;
2240         while (pass_counter++ < MXSER_ISR_PASS_LIMIT) {
2241                 irqbits = inb(brd->vector) & brd->vector_mask;
2242                 if (irqbits == brd->vector_mask)
2243                         break;
2244
2245                 handled = IRQ_HANDLED;
2246                 for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) {
2247                         if (irqbits == brd->vector_mask)
2248                                 break;
2249                         if (bits & irqbits)
2250                                 continue;
2251                         port = &brd->ports[i];
2252
2253                         int_cnt = 0;
2254                         spin_lock(&port->slock);
2255                         do {
2256                                 iir = inb(port->ioaddr + UART_IIR);
2257                                 if (iir & UART_IIR_NO_INT)
2258                                         break;
2259                                 iir &= MOXA_MUST_IIR_MASK;
2260                                 tty = tty_port_tty_get(&port->port);
2261                                 if (!tty ||
2262                                                 (port->port.flags & ASYNC_CLOSING) ||
2263                                                 !(port->port.flags &
2264                                                         ASYNC_INITIALIZED)) {
2265                                         status = inb(port->ioaddr + UART_LSR);
2266                                         outb(0x27, port->ioaddr + UART_FCR);
2267                                         inb(port->ioaddr + UART_MSR);
2268                                         tty_kref_put(tty);
2269                                         break;
2270                                 }
2271
2272                                 status = inb(port->ioaddr + UART_LSR);
2273
2274                                 if (status & UART_LSR_PE)
2275                                         port->err_shadow |= NPPI_NOTIFY_PARITY;
2276                                 if (status & UART_LSR_FE)
2277                                         port->err_shadow |= NPPI_NOTIFY_FRAMING;
2278                                 if (status & UART_LSR_OE)
2279                                         port->err_shadow |=
2280                                                 NPPI_NOTIFY_HW_OVERRUN;
2281                                 if (status & UART_LSR_BI)
2282                                         port->err_shadow |= NPPI_NOTIFY_BREAK;
2283
2284                                 if (port->board->chip_flag) {
2285                                         if (iir == MOXA_MUST_IIR_GDA ||
2286                                             iir == MOXA_MUST_IIR_RDA ||
2287                                             iir == MOXA_MUST_IIR_RTO ||
2288                                             iir == MOXA_MUST_IIR_LSR)
2289                                                 mxser_receive_chars(tty, port,
2290                                                                 &status);
2291
2292                                 } else {
2293                                         status &= port->read_status_mask;
2294                                         if (status & UART_LSR_DR)
2295                                                 mxser_receive_chars(tty, port,
2296                                                                 &status);
2297                                 }
2298                                 msr = inb(port->ioaddr + UART_MSR);
2299                                 if (msr & UART_MSR_ANY_DELTA)
2300                                         mxser_check_modem_status(tty, port, msr);
2301
2302                                 if (port->board->chip_flag) {
2303                                         if (iir == 0x02 && (status &
2304                                                                 UART_LSR_THRE))
2305                                                 mxser_transmit_chars(tty, port);
2306                                 } else {
2307                                         if (status & UART_LSR_THRE)
2308                                                 mxser_transmit_chars(tty, port);
2309                                 }
2310                                 tty_kref_put(tty);
2311                         } while (int_cnt++ < MXSER_ISR_PASS_LIMIT);
2312                         spin_unlock(&port->slock);
2313                 }
2314         }
2315
2316 irq_stop:
2317         return handled;
2318 }
2319
2320 static const struct tty_operations mxser_ops = {
2321         .open = mxser_open,
2322         .close = mxser_close,
2323         .write = mxser_write,
2324         .put_char = mxser_put_char,
2325         .flush_chars = mxser_flush_chars,
2326         .write_room = mxser_write_room,
2327         .chars_in_buffer = mxser_chars_in_buffer,
2328         .flush_buffer = mxser_flush_buffer,
2329         .ioctl = mxser_ioctl,
2330         .throttle = mxser_throttle,
2331         .unthrottle = mxser_unthrottle,
2332         .set_termios = mxser_set_termios,
2333         .stop = mxser_stop,
2334         .start = mxser_start,
2335         .hangup = mxser_hangup,
2336         .break_ctl = mxser_rs_break,
2337         .wait_until_sent = mxser_wait_until_sent,
2338         .tiocmget = mxser_tiocmget,
2339         .tiocmset = mxser_tiocmset,
2340         .get_icount = mxser_get_icount,
2341 };
2342
2343 struct tty_port_operations mxser_port_ops = {
2344         .carrier_raised = mxser_carrier_raised,
2345         .dtr_rts = mxser_dtr_rts,
2346         .activate = mxser_activate,
2347         .shutdown = mxser_shutdown_port,
2348 };
2349
2350 /*
2351  * The MOXA Smartio/Industio serial driver boot-time initialization code!
2352  */
2353
2354 static void mxser_release_ISA_res(struct mxser_board *brd)
2355 {
2356         free_irq(brd->irq, brd);
2357         release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
2358         release_region(brd->vector, 1);
2359 }
2360
2361 static int __devinit mxser_initbrd(struct mxser_board *brd,
2362                 struct pci_dev *pdev)
2363 {
2364         struct mxser_port *info;
2365         unsigned int i;
2366         int retval;
2367
2368         printk(KERN_INFO "mxser: max. baud rate = %d bps\n",
2369                         brd->ports[0].max_baud);
2370
2371         for (i = 0; i < brd->info->nports; i++) {
2372                 info = &brd->ports[i];
2373                 tty_port_init(&info->port);
2374                 info->port.ops = &mxser_port_ops;
2375                 info->board = brd;
2376                 info->stop_rx = 0;
2377                 info->ldisc_stop_rx = 0;
2378
2379                 /* Enhance mode enabled here */
2380                 if (brd->chip_flag != MOXA_OTHER_UART)
2381                         mxser_enable_must_enchance_mode(info->ioaddr);
2382
2383                 info->port.flags = ASYNC_SHARE_IRQ;
2384                 info->type = brd->uart_type;
2385
2386                 process_txrx_fifo(info);
2387
2388                 info->custom_divisor = info->baud_base * 16;
2389                 info->port.close_delay = 5 * HZ / 10;
2390                 info->port.closing_wait = 30 * HZ;
2391                 info->normal_termios = mxvar_sdriver->init_termios;
2392                 memset(&info->mon_data, 0, sizeof(struct mxser_mon));
2393                 info->err_shadow = 0;
2394                 spin_lock_init(&info->slock);
2395
2396                 /* before set INT ISR, disable all int */
2397                 outb(inb(info->ioaddr + UART_IER) & 0xf0,
2398                         info->ioaddr + UART_IER);
2399         }
2400
2401         retval = request_irq(brd->irq, mxser_interrupt, IRQF_SHARED, "mxser",
2402                         brd);
2403         if (retval)
2404                 printk(KERN_ERR "Board %s: Request irq failed, IRQ (%d) may "
2405                         "conflict with another device.\n",
2406                         brd->info->name, brd->irq);
2407
2408         return retval;
2409 }
2410
2411 static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd)
2412 {
2413         int id, i, bits;
2414         unsigned short regs[16], irq;
2415         unsigned char scratch, scratch2;
2416
2417         brd->chip_flag = MOXA_OTHER_UART;
2418
2419         id = mxser_read_register(cap, regs);
2420         switch (id) {
2421         case C168_ASIC_ID:
2422                 brd->info = &mxser_cards[0];
2423                 break;
2424         case C104_ASIC_ID:
2425                 brd->info = &mxser_cards[1];
2426                 break;
2427         case CI104J_ASIC_ID:
2428                 brd->info = &mxser_cards[2];
2429                 break;
2430         case C102_ASIC_ID:
2431                 brd->info = &mxser_cards[5];
2432                 break;
2433         case CI132_ASIC_ID:
2434                 brd->info = &mxser_cards[6];
2435                 break;
2436         case CI134_ASIC_ID:
2437                 brd->info = &mxser_cards[7];
2438                 break;
2439         default:
2440                 return 0;
2441         }
2442
2443         irq = 0;
2444         /* some ISA cards have 2 ports, but we want to see them as 4-port (why?)
2445            Flag-hack checks if configuration should be read as 2-port here. */
2446         if (brd->info->nports == 2 || (brd->info->flags & MXSER_HAS2)) {
2447                 irq = regs[9] & 0xF000;
2448                 irq = irq | (irq >> 4);
2449                 if (irq != (regs[9] & 0xFF00))
2450                         goto err_irqconflict;
2451         } else if (brd->info->nports == 4) {
2452                 irq = regs[9] & 0xF000;
2453                 irq = irq | (irq >> 4);
2454                 irq = irq | (irq >> 8);
2455                 if (irq != regs[9])
2456                         goto err_irqconflict;
2457         } else if (brd->info->nports == 8) {
2458                 irq = regs[9] & 0xF000;
2459                 irq = irq | (irq >> 4);
2460                 irq = irq | (irq >> 8);
2461                 if ((irq != regs[9]) || (irq != regs[10]))
2462                         goto err_irqconflict;
2463         }
2464
2465         if (!irq) {
2466                 printk(KERN_ERR "mxser: interrupt number unset\n");
2467                 return -EIO;
2468         }
2469         brd->irq = ((int)(irq & 0xF000) >> 12);
2470         for (i = 0; i < 8; i++)
2471                 brd->ports[i].ioaddr = (int) regs[i + 1] & 0xFFF8;
2472         if ((regs[12] & 0x80) == 0) {
2473                 printk(KERN_ERR "mxser: invalid interrupt vector\n");
2474                 return -EIO;
2475         }
2476         brd->vector = (int)regs[11];    /* interrupt vector */
2477         if (id == 1)
2478                 brd->vector_mask = 0x00FF;
2479         else
2480                 brd->vector_mask = 0x000F;
2481         for (i = 7, bits = 0x0100; i >= 0; i--, bits <<= 1) {
2482                 if (regs[12] & bits) {
2483                         brd->ports[i].baud_base = 921600;
2484                         brd->ports[i].max_baud = 921600;
2485                 } else {
2486                         brd->ports[i].baud_base = 115200;
2487                         brd->ports[i].max_baud = 115200;
2488                 }
2489         }
2490         scratch2 = inb(cap + UART_LCR) & (~UART_LCR_DLAB);
2491         outb(scratch2 | UART_LCR_DLAB, cap + UART_LCR);
2492         outb(0, cap + UART_EFR);        /* EFR is the same as FCR */
2493         outb(scratch2, cap + UART_LCR);
2494         outb(UART_FCR_ENABLE_FIFO, cap + UART_FCR);
2495         scratch = inb(cap + UART_IIR);
2496
2497         if (scratch & 0xC0)
2498                 brd->uart_type = PORT_16550A;
2499         else
2500                 brd->uart_type = PORT_16450;
2501         if (!request_region(brd->ports[0].ioaddr, 8 * brd->info->nports,
2502                         "mxser(IO)")) {
2503                 printk(KERN_ERR "mxser: can't request ports I/O region: "
2504                                 "0x%.8lx-0x%.8lx\n",
2505                                 brd->ports[0].ioaddr, brd->ports[0].ioaddr +
2506                                 8 * brd->info->nports - 1);
2507                 return -EIO;
2508         }
2509         if (!request_region(brd->vector, 1, "mxser(vector)")) {
2510                 release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
2511                 printk(KERN_ERR "mxser: can't request interrupt vector region: "
2512                                 "0x%.8lx-0x%.8lx\n",
2513                                 brd->ports[0].ioaddr, brd->ports[0].ioaddr +
2514                                 8 * brd->info->nports - 1);
2515                 return -EIO;
2516         }
2517         return brd->info->nports;
2518
2519 err_irqconflict:
2520         printk(KERN_ERR "mxser: invalid interrupt number\n");
2521         return -EIO;
2522 }
2523
2524 static int __devinit mxser_probe(struct pci_dev *pdev,
2525                 const struct pci_device_id *ent)
2526 {
2527 #ifdef CONFIG_PCI
2528         struct mxser_board *brd;
2529         unsigned int i, j;
2530         unsigned long ioaddress;
2531         int retval = -EINVAL;
2532
2533         for (i = 0; i < MXSER_BOARDS; i++)
2534                 if (mxser_boards[i].info == NULL)
2535                         break;
2536
2537         if (i >= MXSER_BOARDS) {
2538                 dev_err(&pdev->dev, "too many boards found (maximum %d), board "
2539                                 "not configured\n", MXSER_BOARDS);
2540                 goto err;
2541         }
2542
2543         brd = &mxser_boards[i];
2544         brd->idx = i * MXSER_PORTS_PER_BOARD;
2545         dev_info(&pdev->dev, "found MOXA %s board (BusNo=%d, DevNo=%d)\n",
2546                 mxser_cards[ent->driver_data].name,
2547                 pdev->bus->number, PCI_SLOT(pdev->devfn));
2548
2549         retval = pci_enable_device(pdev);
2550         if (retval) {
2551                 dev_err(&pdev->dev, "PCI enable failed\n");
2552                 goto err;
2553         }
2554
2555         /* io address */
2556         ioaddress = pci_resource_start(pdev, 2);
2557         retval = pci_request_region(pdev, 2, "mxser(IO)");
2558         if (retval)
2559                 goto err_dis;
2560
2561         brd->info = &mxser_cards[ent->driver_data];
2562         for (i = 0; i < brd->info->nports; i++)
2563                 brd->ports[i].ioaddr = ioaddress + 8 * i;
2564
2565         /* vector */
2566         ioaddress = pci_resource_start(pdev, 3);
2567         retval = pci_request_region(pdev, 3, "mxser(vector)");
2568         if (retval)
2569                 goto err_zero;
2570         brd->vector = ioaddress;
2571
2572         /* irq */
2573         brd->irq = pdev->irq;
2574
2575         brd->chip_flag = CheckIsMoxaMust(brd->ports[0].ioaddr);
2576         brd->uart_type = PORT_16550A;
2577         brd->vector_mask = 0;
2578
2579         for (i = 0; i < brd->info->nports; i++) {
2580                 for (j = 0; j < UART_INFO_NUM; j++) {
2581                         if (Gpci_uart_info[j].type == brd->chip_flag) {
2582                                 brd->ports[i].max_baud =
2583                                         Gpci_uart_info[j].max_baud;
2584
2585                                 /* exception....CP-102 */
2586                                 if (brd->info->flags & MXSER_HIGHBAUD)
2587                                         brd->ports[i].max_baud = 921600;
2588                                 break;
2589                         }
2590                 }
2591         }
2592
2593         if (brd->chip_flag == MOXA_MUST_MU860_HWID) {
2594                 for (i = 0; i < brd->info->nports; i++) {
2595                         if (i < 4)
2596                                 brd->ports[i].opmode_ioaddr = ioaddress + 4;
2597                         else
2598                                 brd->ports[i].opmode_ioaddr = ioaddress + 0x0c;
2599                 }
2600                 outb(0, ioaddress + 4); /* default set to RS232 mode */
2601                 outb(0, ioaddress + 0x0c);      /* default set to RS232 mode */
2602         }
2603
2604         for (i = 0; i < brd->info->nports; i++) {
2605                 brd->vector_mask |= (1 << i);
2606                 brd->ports[i].baud_base = 921600;
2607         }
2608
2609         /* mxser_initbrd will hook ISR. */
2610         retval = mxser_initbrd(brd, pdev);
2611         if (retval)
2612                 goto err_rel3;
2613
2614         for (i = 0; i < brd->info->nports; i++)
2615                 tty_register_device(mxvar_sdriver, brd->idx + i, &pdev->dev);
2616
2617         pci_set_drvdata(pdev, brd);
2618
2619         return 0;
2620 err_rel3:
2621         pci_release_region(pdev, 3);
2622 err_zero:
2623         brd->info = NULL;
2624         pci_release_region(pdev, 2);
2625 err_dis:
2626         pci_disable_device(pdev);
2627 err:
2628         return retval;
2629 #else
2630         return -ENODEV;
2631 #endif
2632 }
2633
2634 static void __devexit mxser_remove(struct pci_dev *pdev)
2635 {
2636 #ifdef CONFIG_PCI
2637         struct mxser_board *brd = pci_get_drvdata(pdev);
2638         unsigned int i;
2639
2640         for (i = 0; i < brd->info->nports; i++)
2641                 tty_unregister_device(mxvar_sdriver, brd->idx + i);
2642
2643         free_irq(pdev->irq, brd);
2644         pci_release_region(pdev, 2);
2645         pci_release_region(pdev, 3);
2646         pci_disable_device(pdev);
2647         brd->info = NULL;
2648 #endif
2649 }
2650
2651 static struct pci_driver mxser_driver = {
2652         .name = "mxser",
2653         .id_table = mxser_pcibrds,
2654         .probe = mxser_probe,
2655         .remove = __devexit_p(mxser_remove)
2656 };
2657
2658 static int __init mxser_module_init(void)
2659 {
2660         struct mxser_board *brd;
2661         unsigned int b, i, m;
2662         int retval;
2663
2664         mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1);
2665         if (!mxvar_sdriver)
2666                 return -ENOMEM;
2667
2668         printk(KERN_INFO "MOXA Smartio/Industio family driver version %s\n",
2669                 MXSER_VERSION);
2670
2671         /* Initialize the tty_driver structure */
2672         mxvar_sdriver->owner = THIS_MODULE;
2673         mxvar_sdriver->magic = TTY_DRIVER_MAGIC;
2674         mxvar_sdriver->name = "ttyMI";
2675         mxvar_sdriver->major = ttymajor;
2676         mxvar_sdriver->minor_start = 0;
2677         mxvar_sdriver->num = MXSER_PORTS + 1;
2678         mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL;
2679         mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL;
2680         mxvar_sdriver->init_termios = tty_std_termios;
2681         mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL;
2682         mxvar_sdriver->flags = TTY_DRIVER_REAL_RAW|TTY_DRIVER_DYNAMIC_DEV;
2683         tty_set_operations(mxvar_sdriver, &mxser_ops);
2684
2685         retval = tty_register_driver(mxvar_sdriver);
2686         if (retval) {
2687                 printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family "
2688                                 "tty driver !\n");
2689                 goto err_put;
2690         }
2691
2692         /* Start finding ISA boards here */
2693         for (m = 0, b = 0; b < MXSER_BOARDS; b++) {
2694                 if (!ioaddr[b])
2695                         continue;
2696
2697                 brd = &mxser_boards[m];
2698                 retval = mxser_get_ISA_conf(ioaddr[b], brd);
2699                 if (retval <= 0) {
2700                         brd->info = NULL;
2701                         continue;
2702                 }
2703
2704                 printk(KERN_INFO "mxser: found MOXA %s board (CAP=0x%lx)\n",
2705                                 brd->info->name, ioaddr[b]);
2706
2707                 /* mxser_initbrd will hook ISR. */
2708                 if (mxser_initbrd(brd, NULL) < 0) {
2709                         brd->info = NULL;
2710                         continue;
2711                 }
2712
2713                 brd->idx = m * MXSER_PORTS_PER_BOARD;
2714                 for (i = 0; i < brd->info->nports; i++)
2715                         tty_register_device(mxvar_sdriver, brd->idx + i, NULL);
2716
2717                 m++;
2718         }
2719
2720         retval = pci_register_driver(&mxser_driver);
2721         if (retval) {
2722                 printk(KERN_ERR "mxser: can't register pci driver\n");
2723                 if (!m) {
2724                         retval = -ENODEV;
2725                         goto err_unr;
2726                 } /* else: we have some ISA cards under control */
2727         }
2728
2729         return 0;
2730 err_unr:
2731         tty_unregister_driver(mxvar_sdriver);
2732 err_put:
2733         put_tty_driver(mxvar_sdriver);
2734         return retval;
2735 }
2736
2737 static void __exit mxser_module_exit(void)
2738 {
2739         unsigned int i, j;
2740
2741         pci_unregister_driver(&mxser_driver);
2742
2743         for (i = 0; i < MXSER_BOARDS; i++) /* ISA remains */
2744                 if (mxser_boards[i].info != NULL)
2745                         for (j = 0; j < mxser_boards[i].info->nports; j++)
2746                                 tty_unregister_device(mxvar_sdriver,
2747                                                 mxser_boards[i].idx + j);
2748         tty_unregister_driver(mxvar_sdriver);
2749         put_tty_driver(mxvar_sdriver);
2750
2751         for (i = 0; i < MXSER_BOARDS; i++)
2752                 if (mxser_boards[i].info != NULL)
2753                         mxser_release_ISA_res(&mxser_boards[i]);
2754 }
2755
2756 module_init(mxser_module_init);
2757 module_exit(mxser_module_exit);